Git Repo - linux.git/log

drm/exynos/mixer: fix MIXER shadow registry synchronisation code

MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
  ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
  ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:

[   25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[   25.677888] ------------[ cut here ]------------
[   25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[   25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[   25.693778] Modules linked in:
[   25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[   25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[   25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[   25.716470] LR is at lock_is_held_type+0x44/0x64

v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync

Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

scsi: ibmvscsi: Fix empty event pool access during host removal

The event pool used for queueing commands is destroyed fairly early in the
ibmvscsi_remove() code path. Since, this happens prior to the call so
scsi_remove_host() it is possible for further calls to queuecommand to be
processed which manifest as a panic due to a NULL pointer dereference as
seen here:

PANIC: "Unable to handle kernel paging request for data at address
0x00000000"

Context process backtrace:

DSISR: 0000000042000000 ????Syscall Result: 0000000000000000
4 [c000000002cb3820] memcpy_power7 at c000000000064204
[Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4
5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable)
6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi]
7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod]
8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod]
9 [c000000002cb3be0] __blk_run_queue at c000000000429860
10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec
11 [c000000002cb3c40] process_one_work at c0000000000dac30
12 [c000000002cb3cd0] worker_thread at c0000000000db110
13 [c000000002cb3d80] kthread at c0000000000e3378
14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c

The kernel buffer log is overfilled with this log:

[11261.952732] ibmvscsi: found no event struct in pool!

This patch reorders the operations during host teardown. Start by calling
the SRP transport and Scsi_Host remove functions to flush any outstanding
work and set the host offline. LLDD teardown follows including destruction
of the event pool, freeing the Command Response Queue (CRQ), and unmapping
any persistent buffers. The event pool destruction is protected by the
scsi_host lock, and the pool is purged prior of any requests for which we
never received a response. Finally, move the removal of the scsi host from
our global list to the end so that the host is easily locatable for
debugging purposes during teardown.

Cc: <stable@vger.kernel.org> # v2.6.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ibmvscsi: Protect ibmvscsi_head from concurrent modificaiton

For each ibmvscsi host created during a probe or destroyed during a remove
we either add or remove that host to/from the global ibmvscsi_head
list. This runs the risk of concurrent modification.

This patch adds a simple spinlock around the list modification calls to
prevent concurrent updates as is done similarly in the ibmvfc driver and
ipr driver.

Fixes: 32d6e4b6e4ea ("scsi: ibmvscsi: add vscsi hosts to global list_head")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

blkcg: Fix kernel-doc warnings

Avoid that the following warnings are reported when building with W=1:

block/blk-cgroup.c:1755: warning: Function parameter or member 'q' not described in 'blkcg_schedule_throttle'
block/blk-cgroup.c:1755: warning: Function parameter or member 'use_memdelay' not described in 'blkcg_schedule_throttle'
block/blk-cgroup.c:1779: warning: Function parameter or member 'blkg' not described in 'blkcg_add_delay'
block/blk-cgroup.c:1779: warning: Function parameter or member 'now' not described in 'blkcg_add_delay'
block/blk-cgroup.c:1779: warning: Function parameter or member 'delta' not described in 'blkcg_add_delay'

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

blk-iolatency: #include "blk.h"

This patch avoids that the following warning is reported when building
with W=1:

block/blk-iolatency.c:734:5: warning: no previous prototype for 'blk_iolatency_init' [-Wmissing-prototypes]

Cc: Josef Bacik <jbacik@fb.com>
Fixes: d70675121546 ("block: introduce blk-iolatency io controller") # v4.19
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: Unexport blk_mq_add_to_requeue_list()

This function is not used outside the block layer core. Hence unexport it.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: add BLK_MQ_POLL_CLASSIC for hybrid poll and return EINVAL for unexpected value

For q->poll_nsec == -1, means doing classic poll, not hybrid poll.
We introduce a new flag BLK_MQ_POLL_CLASSIC to replace -1, which
may make code much easier to read.

Additionally, since val is an int obtained with kstrtoint(), val can be
a negative value other than -1, so return -EINVAL for that case.

Thanks to Damien Le Moal for some good suggestion.

Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

perf annotate: Enable annotation of BPF programs

In symbol__disassemble(), DSO_BINARY_TYPE__BPF_PROG_INFO dso calls into
a new function symbol__disassemble_bpf(), where annotation line
information is filled based on the bpf_prog_info and btf data saved in
given perf_env.

symbol__disassemble_bpf() uses binutils's libopcodes to disassemble bpf
programs.

Committer testing:

After fixing this:

  -               u64 *addrs = (u64 *)(info_linear->info.jited_ksyms);
  +               u64 *addrs = (u64 *)(uintptr_t)(info_linear->info.jited_ksyms);

Detected when crossbuilding to a 32-bit arch.

And making all this dependent on HAVE_LIBBFD_SUPPORT and
HAVE_LIBBPF_SUPPORT:

1) Have a BPF program running, one that has BTF info, etc, I used
   the tools/perf/examples/bpf/augmented_raw_syscalls.c put in place
   by 'perf trace'.

  # grep -B1 augmented_raw ~/.perfconfig
  [trace]
add_events = /home/acme/git/perf/tools/perf/examples/bpf/augmented_raw_syscalls.c
  #
  # perf trace -e *mmsg
  dnf/6245 sendmmsg(20, 0x7f5485a88030, 2, MSG_NOSIGNAL) = 2
  NetworkManager/10055 sendmmsg(22<socket:[1056822]>, 0x7f8126ad1bb0, 2, MSG_NOSIGNAL) = 2

2) Then do a 'perf record' system wide for a while:

  # perf record -a
  ^C[ perf record: Woken up 68 times to write data ]
  [ perf record: Captured and wrote 19.427 MB perf.data (366891 samples) ]
  #

3) Check that we captured BPF and BTF info in the perf.data file:

  # perf report --header-only | grep 'b[pt]f'
  # event : name = cycles:ppp, , id = { 294789, 294790, 294791, 294792, 294793, 294794, 294795, 294796 }, size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|CPU|PERIOD, read_format = ID, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1, ksymbol = 1, bpf_event = 1
  # bpf_prog_info of id 13
  # bpf_prog_info of id 14
  # bpf_prog_info of id 15
  # bpf_prog_info of id 16
  # bpf_prog_info of id 17
  # bpf_prog_info of id 18
  # bpf_prog_info of id 21
  # bpf_prog_info of id 22
  # bpf_prog_info of id 41
  # bpf_prog_info of id 42
  # btf info of id 2
  #

4) Check which programs got recorded:

   # perf report | grep bpf_prog | head
     0.16%  exe              bpf_prog_819967866022f1e1_sys_enter      [k] bpf_prog_819967866022f1e1_sys_enter
     0.14%  exe              bpf_prog_c1bd85c092d6e4aa_sys_exit       [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
     0.08%  fuse-overlayfs   bpf_prog_819967866022f1e1_sys_enter      [k] bpf_prog_819967866022f1e1_sys_enter
     0.07%  fuse-overlayfs   bpf_prog_c1bd85c092d6e4aa_sys_exit       [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
     0.01%  clang-4.0        bpf_prog_c1bd85c092d6e4aa_sys_exit       [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
     0.01%  clang-4.0        bpf_prog_819967866022f1e1_sys_enter      [k] bpf_prog_819967866022f1e1_sys_enter
     0.00%  clang            bpf_prog_c1bd85c092d6e4aa_sys_exit       [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
     0.00%  runc             bpf_prog_819967866022f1e1_sys_enter      [k] bpf_prog_819967866022f1e1_sys_enter
     0.00%  clang            bpf_prog_819967866022f1e1_sys_enter      [k] bpf_prog_819967866022f1e1_sys_enter
     0.00%  sh               bpf_prog_c1bd85c092d6e4aa_sys_exit       [k] bpf_prog_c1bd85c092d6e4aa_sys_exit
  #

  This was with the default --sort order for 'perf report', which is:

    --sort comm,dso,symbol

  If we just look for the symbol, for instance:

   # perf report --sort symbol | grep bpf_prog | head
     0.26%  [k] bpf_prog_819967866022f1e1_sys_enter                -      -
     0.24%  [k] bpf_prog_c1bd85c092d6e4aa_sys_exit                 -      -
   #

  or the DSO:

   # perf report --sort dso | grep bpf_prog | head
     0.26%  bpf_prog_819967866022f1e1_sys_enter
     0.24%  bpf_prog_c1bd85c092d6e4aa_sys_exit
  #

We'll see the two BPF programs that augmented_raw_syscalls.o puts in
place,  one attached to the raw_syscalls:sys_enter and another to the
raw_syscalls:sys_exit tracepoints, as expected.

Now we can finally do, from the command line, annotation for one of
those two symbols, with the original BPF program source coude intermixed
with the disassembled JITed code:

  # perf annotate --stdio2 bpf_prog_819967866022f1e1_sys_enter

  Samples: 950  of event 'cycles:ppp', 4000 Hz, Event count (approx.): 553756947, [percent: local period]
  bpf_prog_819967866022f1e1_sys_enter() bpf_prog_819967866022f1e1_sys_enter
  Percent      int sys_enter(struct syscall_enter_args *args)
   53.41         push   %rbp

    0.63         mov    %rsp,%rbp
    0.31         sub    $0x170,%rsp
    1.93         sub    $0x28,%rbp
    7.02         mov    %rbx,0x0(%rbp)
    3.20         mov    %r13,0x8(%rbp)
    1.07         mov    %r14,0x10(%rbp)
    0.61         mov    %r15,0x18(%rbp)
    0.11         xor    %eax,%eax
    1.29         mov    %rax,0x20(%rbp)
    0.11         mov    %rdi,%rbx
                return bpf_get_current_pid_tgid();
    2.02       → callq  *ffffffffda6776d9
    2.76         mov    %eax,-0x148(%rbp)
                 mov    %rbp,%rsi
               int sys_enter(struct syscall_enter_args *args)
                 add    $0xfffffffffffffeb8,%rsi
                return bpf_map_lookup_elem(pids, &pid) != NULL;
                 movabs $0xffff975ac2607800,%rdi

    1.26       → callq  *ffffffffda6789e9
                 cmp    $0x0,%rax
    2.43       → je     0
                 add    $0x38,%rax
    0.21         xor    %r13d,%r13d
                if (pid_filter__has(&pids_filtered, getpid()))
    0.81         cmp    $0x0,%rax
               → jne    0
                 mov    %rbp,%rdi
                probe_read(&augmented_args.args, sizeof(augmented_args.args), args);
    2.22         add    $0xfffffffffffffeb8,%rdi
    0.11         mov    $0x40,%esi
    0.32         mov    %rbx,%rdx
    2.74       → callq  *ffffffffda658409
                syscall = bpf_map_lookup_elem(&syscalls, &augmented_args.args.syscall_nr);
    0.22         mov    %rbp,%rsi
    1.69         add    $0xfffffffffffffec0,%rsi
                syscall = bpf_map_lookup_elem(&syscalls, &augmented_args.args.syscall_nr);
                 movabs $0xffff975bfcd36000,%rdi

                 add    $0xd0,%rdi
    0.21         mov    0x0(%rsi),%eax
    0.93         cmp    $0x200,%rax
               → jae    0
    0.10         shl    $0x3,%rax

    0.11         add    %rdi,%rax
    0.11       → jmp    0
                 xor    %eax,%eax
                if (syscall == NULL || !syscall->enabled)
    1.07         cmp    $0x0,%rax
               → je     0
                if (syscall == NULL || !syscall->enabled)
    6.57         movzbq 0x0(%rax),%rdi

                if (syscall == NULL || !syscall->enabled)
                 cmp    $0x0,%rdi
    0.95       → je     0
                 mov    $0x40,%r8d
                switch (augmented_args.args.syscall_nr) {
                 mov    -0x140(%rbp),%rdi
                switch (augmented_args.args.syscall_nr) {
                 cmp    $0x2,%rdi
               → je     0
                 cmp    $0x101,%rdi
               → je     0
                 cmp    $0x15,%rdi
               → jne    0
                case SYS_OPEN: filename_arg = (const void *)args->args[0];
                 mov    0x10(%rbx),%rdx
               → jmp    0
                case SYS_OPENAT: filename_arg = (const void *)args->args[1];
                 mov    0x18(%rbx),%rdx
                if (filename_arg != NULL) {
                 cmp    $0x0,%rdx
               → je     0
                 xor    %edi,%edi
                augmented_args.filename.reserved = 0;
                 mov    %edi,-0x104(%rbp)
                augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
                 mov    %rbp,%rdi
                 add    $0xffffffffffffff00,%rdi
                augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
                 mov    $0x100,%esi
               → callq  *ffffffffda658499
                 mov    $0x148,%r8d
                augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
                 mov    %eax,-0x108(%rbp)
                augmented_args.filename.size = probe_read_str(&augmented_args.filename.value,
                 mov    %rax,%rdi
                 shl    $0x20,%rdi

                 shr    $0x20,%rdi

                if (augmented_args.filename.size < sizeof(augmented_args.filename.value)) {
                 cmp    $0xff,%rdi
               → ja     0
                len -= sizeof(augmented_args.filename.value) - augmented_args.filename.size;
                 add    $0x48,%rax
                len &= sizeof(augmented_args.filename.value) - 1;
                 and    $0xff,%rax
                 mov    %rax,%r8
                 mov    %rbp,%rcx
                return perf_event_output(args, &__augmented_syscalls__, BPF_F_CURRENT_CPU, &augmented_args, len);
                 add    $0xfffffffffffffeb8,%rcx
                 mov    %rbx,%rdi
                 movabs $0xffff975fbd72d800,%rsi

                 mov    $0xffffffff,%edx
               → callq  *ffffffffda658ad9
                 mov    %rax,%r13
               }
                 mov    %r13,%rax
    0.72         mov    0x0(%rbp),%rbx
                 mov    0x8(%rbp),%r13
    1.16         mov    0x10(%rbp),%r14
    0.10         mov    0x18(%rbp),%r15
    0.42         add    $0x28,%rbp
    0.54         leaveq
    0.54       ← retq
  #

Please see 'man perf-config' to see how to control what should be seen,
via ~/.perfconfig [annotate] section, for instance, one can suppress the
source code and see just the disassembly, etc.

Alternatively, use the TUI bu just using 'perf annotate', press
'/bpf_prog' to see the bpf symbols, press enter and do the interactive
annotation, which allows for dumping to a file after selecting the
the various output tunables, for instance, the above without source code
intermixed, plus showing all the instruction offsets:

  # perf annotate bpf_prog_819967866022f1e1_sys_enter

Then press: 's' to hide the source code + 'O' twice to show all
instruction offsets, then 'P' to print to the
bpf_prog_819967866022f1e1_sys_enter.annotation file, which will have:

  # cat bpf_prog_819967866022f1e1_sys_enter.annotation
  bpf_prog_819967866022f1e1_sys_enter() bpf_prog_819967866022f1e1_sys_enter
  Event: cycles:ppp

   53.41    0:   push   %rbp

    0.63    1:   mov    %rsp,%rbp
    0.31    4:   sub    $0x170,%rsp
    1.93    b:   sub    $0x28,%rbp
    7.02    f:   mov    %rbx,0x0(%rbp)
    3.20   13:   mov    %r13,0x8(%rbp)
    1.07   17:   mov    %r14,0x10(%rbp)
    0.61   1b:   mov    %r15,0x18(%rbp)
    0.11   1f:   xor    %eax,%eax
    1.29   21:   mov    %rax,0x20(%rbp)
    0.11   25:   mov    %rdi,%rbx
    2.02   28: → callq  *ffffffffda6776d9
    2.76   2d:   mov    %eax,-0x148(%rbp)
           33:   mov    %rbp,%rsi
           36:   add    $0xfffffffffffffeb8,%rsi
           3d:   movabs $0xffff975ac2607800,%rdi

    1.26   47: → callq  *ffffffffda6789e9
           4c:   cmp    $0x0,%rax
    2.43   50: → je     0
           52:   add    $0x38,%rax
    0.21   56:   xor    %r13d,%r13d
    0.81   59:   cmp    $0x0,%rax
           5d: → jne    0
           63:   mov    %rbp,%rdi
    2.22   66:   add    $0xfffffffffffffeb8,%rdi
    0.11   6d:   mov    $0x40,%esi
    0.32   72:   mov    %rbx,%rdx
    2.74   75: → callq  *ffffffffda658409
    0.22   7a:   mov    %rbp,%rsi
    1.69   7d:   add    $0xfffffffffffffec0,%rsi
           84:   movabs $0xffff975bfcd36000,%rdi

           8e:   add    $0xd0,%rdi
    0.21   95:   mov    0x0(%rsi),%eax
    0.93   98:   cmp    $0x200,%rax
           9f: → jae    0
    0.10   a1:   shl    $0x3,%rax

    0.11   a5:   add    %rdi,%rax
    0.11   a8: → jmp    0
           aa:   xor    %eax,%eax
    1.07   ac:   cmp    $0x0,%rax
           b0: → je     0
    6.57   b6:   movzbq 0x0(%rax),%rdi

           bb:   cmp    $0x0,%rdi
    0.95   bf: → je     0
           c5:   mov    $0x40,%r8d
           cb:   mov    -0x140(%rbp),%rdi
           d2:   cmp    $0x2,%rdi
           d6: → je     0
           d8:   cmp    $0x101,%rdi
           df: → je     0
           e1:   cmp    $0x15,%rdi
           e5: → jne    0
           e7:   mov    0x10(%rbx),%rdx
           eb: → jmp    0
           ed:   mov    0x18(%rbx),%rdx
           f1:   cmp    $0x0,%rdx
           f5: → je     0
           f7:   xor    %edi,%edi
           f9:   mov    %edi,-0x104(%rbp)
           ff:   mov    %rbp,%rdi
          102:   add    $0xffffffffffffff00,%rdi
          109:   mov    $0x100,%esi
          10e: → callq  *ffffffffda658499
          113:   mov    $0x148,%r8d
          119:   mov    %eax,-0x108(%rbp)
          11f:   mov    %rax,%rdi
          122:   shl    $0x20,%rdi

          126:   shr    $0x20,%rdi

          12a:   cmp    $0xff,%rdi
          131: → ja     0
          133:   add    $0x48,%rax
          137:   and    $0xff,%rax
          13d:   mov    %rax,%r8
          140:   mov    %rbp,%rcx
          143:   add    $0xfffffffffffffeb8,%rcx
          14a:   mov    %rbx,%rdi
          14d:   movabs $0xffff975fbd72d800,%rsi

          157:   mov    $0xffffffff,%edx
          15c: → callq  *ffffffffda658ad9
          161:   mov    %rax,%r13
          164:   mov    %r13,%rax
    0.72  167:   mov    0x0(%rbp),%rbx
          16b:   mov    0x8(%rbp),%r13
    1.16  16f:   mov    0x10(%rbp),%r14
    0.10  173:   mov    0x18(%rbp),%r15
    0.42  177:   add    $0x28,%rbp
    0.54  17b:   leaveq
    0.54  17c: ← retq

Another cool way to test all this is to symple use 'perf top' look for
those symbols, go there and press enter, annotate it live :-)

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf build: Check what binutils's 'disassembler()' signature to use

Commit 003ca0fd2286 ("Refactor disassembler selection") in the binutils
repo, which changed the disassembler() function signature, so we must
use the feature test introduced in fb982666e380 ("tools/bpftool: fix
bpftool build with bintutils >= 2.9") to deal with that.

Committer testing:

After adding the missing function call to test-all.c, and:

  FEATURE_CHECK_LDFLAGS-disassembler-four-args = -bfd -lopcodes

And the fallbacks for cases where we need -liberty and sometimes -lz to
tools/perf/Makefile.config, we get:

  $ make -C tools/perf O=/tmp/build/perf install-bin
  make: Entering directory '/home/acme/git/perf/tools/perf'
    BUILD:   Doing 'make -j8' parallel build

  Auto-detecting system features:
  ...                         dwarf: [ on  ]
  ...            dwarf_getlocations: [ on  ]
  ...                         glibc: [ on  ]
  ...                          gtk2: [ on  ]
  ...                      libaudit: [ on  ]
  ...                        libbfd: [ on  ]
  ...                        libelf: [ on  ]
  ...                       libnuma: [ on  ]
  ...        numa_num_possible_cpus: [ on  ]
  ...                       libperl: [ on  ]
  ...                     libpython: [ on  ]
  ...                      libslang: [ on  ]
  ...                     libcrypto: [ on  ]
  ...                     libunwind: [ on  ]
  ...            libdw-dwarf-unwind: [ on  ]
  ...                          zlib: [ on  ]
  ...                          lzma: [ on  ]
  ...                     get_cpuid: [ on  ]
  ...                           bpf: [ on  ]
  ...                        libaio: [ on  ]
  ...        disassembler-four-args: [ on  ]
    CC       /tmp/build/perf/jvmti/libjvmti.o
    CC       /tmp/build/perf/builtin-bench.o
  <SNIP>
  $
  $

The feature detection test-all.bin gets successfully built and linked:

  $ ls -la /tmp/build/perf/feature/test-all.bin
  -rwxrwxr-x. 1 acme acme 2680352 Mar 19 11:07 /tmp/build/perf/feature/test-all.bin
  $ nm /tmp/build/perf/feature/test-all.bin  | grep -w disassembler
  0000000000061f90 T disassembler
  $

Time to move on to the patches that make use of this disassembler()
routine in binutils's libopcodes.

Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com
[ split from a larger patch, added missing FEATURE_CHECK_LDFLAGS-disassembler-four-args ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

scsi: hisi_sas: Add softreset in hisi_sas_I_T_nexus_reset()

We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.

In commit ffb1c820b8b6 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.

We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.

Fixes: ffb1c820b8b6 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

irqchip/gic-v3-its: Fix comparison logic in lpi_range_cmp

The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.

Fixes: 880cb3cddd16 (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Merge tag 'arc-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc

Pull ARC updates from Vineet Gupta:

- unaligned access support for HS cores

- Removed extra memory barrier around spinlock code

- HSDK platform updates: enable dmac, reset

- some more boot logging updates

- misc minor fixes

* tag 'arc-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  arch: arc: Kconfig: pedantic formatting
  ARCv2: spinlock: remove the extra smp_mb before lock, after unlock
  ARC: unaligned: relax the check for gcc supporting -mno-unaligned-access
  ARC: boot log: cut down on verbosity
  ARCv2: boot log: refurbish HS core/release identification
  arc: hsdk_defconfig: Enable CONFIG_BLK_DEV_RAM
  ARC: u-boot args: check that magic number is correct
  ARC: perf: bpok condition only exists for ARCompact
  ARCv2: Add explcit unaligned access support (and ability to disable too)
  ARCv2: lib: introduce memcpy optimized for unaligned access
  ARC: [plat-hsdk]: Enable AXI DW DMAC support
  ARC: [plat-hsdk]: Add reset controller handle to manage USB reset
  ARC: DTB: [scripted] fix node name and address spelling

arm64: remove obsolete selection of MULTI_IRQ_HANDLER

The arm64 config selects MULTI_IRQ_HANDLER, which was renamed to
GENERIC_IRQ_MULTI_HANDLER by commit 4c301f9b6a94 ("ARM: Convert
to GENERIC_IRQ_MULTI_HANDLER"). The 'new' option is already
selected, so just remove the obsolete entry.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

rbd: drop wait_for_latest_osdmap()

Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>

libceph: wait for latest osdmap in ceph_monc_blacklist_add()

Because map updates are distributed lazily, an OSD may not know about
the new blacklist for quite some time after "osd blacklist add" command
is completed. This makes it possible for a blacklisted but still alive
client to overwrite a post-blacklist update, resulting in data
corruption.

Waiting for latest osdmap in ceph_monc_blacklist_add() and thus using
the post-blacklist epoch for all post-blacklist requests ensures that
all such requests "wait" for the blacklist to come into force on their
respective OSDs.

Cc: stable@vger.kernel.org
Fixes: 6305a3b41515 ("libceph: support for blacklisting clients")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>

powerpc/mm: Only define MAX_PHYSMEM_BITS in SPARSEMEM configurations

MAX_PHYSMEM_BITS only needs to be defined if CONFIG_SPARSEMEM is
enabled, and that was the case before commit 4ffe713b7587
("powerpc/mm: Increase the max addressable memory to 2PB").

On 32-bit systems, where CONFIG_SPARSEMEM is not enabled, we now
define it as 46.  That is larger than the real number of physical
address bits, and breaks calculations in zsmalloc:

  mm/zsmalloc.c:130:49: warning: right shift count is negative
    MAX(32, (ZS_MAX_PAGES_PER_ZSPAGE << PAGE_SHIFT >> OBJ_INDEX_BITS))
                                                   ^~
  ...
  mm/zsmalloc.c:253:21: error: variably modified 'size_class' at file scope
    struct size_class *size_class[ZS_SIZE_CLASSES];
                       ^~~~~~~~~~

Fixes: 4ffe713b7587 ("powerpc/mm: Increase the max addressable memory to 2PB")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

drm/vmwgfx: Don't double-free the mode stored in par->set_mode

When calling vmw_fb_set_par(), the mode stored in par->set_mode gets free'd
twice. The first free is in vmw_fb_kms_detach(), the second is near the
end of vmw_fb_set_par() under the name of 'old_mode'. The mode-setting code
only works correctly if the mode doesn't actually change. Removing
'old_mode' in favor of using par->set_mode directly fixes the problem.

Cc: <stable@vger.kernel.org>
Fixes: a278724aa23c ("drm/vmwgfx: Implement fbdev on kms v2")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>

drm/vmwgfx: Return 0 when gmrid::get_node runs out of ID's

If it's not a system error and get_node implementation accommodate the
buffer object then it should return 0 with memm::mm_node set to NULL.

v2: Test for id != -ENOMEM instead of id == -ENOSPC.

Cc: <stable@vger.kernel.org>
Fixes: 4eb085e42fde ("drm/vmwgfx: Convert to new IDA API")
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>

PM / Domains: Avoid a potential deadlock

Lockdep warns that prepare_lock and genpd->mlock can cause a deadlock
the deadlock scenario is like following:
First thread is probing cs2000
cs2000_probe()
  clk_register()
    __clk_core_init()
      clk_prepare_lock()                            ----> acquires prepare_lock
        cs2000_recalc_rate()
          i2c_smbus_read_byte_data()
            rcar_i2c_master_xfer()
              dma_request_chan()
                rcar_dmac_of_xlate()
                  rcar_dmac_alloc_chan_resources()
                    pm_runtime_get_sync()
                      __pm_runtime_resume()
                        rpm_resume()
                          rpm_callback()
                            genpd_runtime_resume()   ----> acquires genpd->mlock

Second thread is attaching any device to the same PM domain
genpd_add_device()
  genpd_lock()                                       ----> acquires genpd->mlock
    cpg_mssr_attach_dev()
      of_clk_get_from_provider()
        __of_clk_get_from_provider()
          __clk_create_clk()
            clk_prepare_lock()                       ----> acquires prepare_lock

Since currently no PM provider access genpd's critical section
in .attach_dev, and .detach_dev callbacks, so there is no need to protect
these two callbacks with genpd->mlock.
This patch avoids a potential deadlock by moving out .attach_dev and .detach_dev
from genpd->mlock, so that genpd->mlock won't be held when prepare_lock is acquired
in .attach_dev and .detach_dev

Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPI / utils: Drop reference in test for device presence

When commit 8661423eea1a ("ACPI / utils: Add new acpi_dev_present
helper") introduced acpi_dev_present(), it missed the fact that
bus_find_device() took a reference on the device found by it and
the callers of acpi_dev_present() don't drop that reference.

Drop the reference on the device in acpi_dev_present().

Fixes: 8661423eea1a ("ACPI / utils: Add new acpi_dev_present helper")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

perf bpf: Process PERF_BPF_EVENT_PROG_LOAD for annotation

This patch adds processing of PERF_BPF_EVENT_PROG_LOAD, which sets
proper DSO type/id/etc of memory regions mapped to BPF programs to
DSO_BINARY_TYPE__BPF_PROG_INFO.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-14-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf symbols: Introduce DSO_BINARY_TYPE__BPF_PROG_INFO

Introduce a new dso type DSO_BINARY_TYPE__BPF_PROG_INFO for BPF programs. In
symbol__disassemble(), DSO_BINARY_TYPE__BPF_PROG_INFO dso will call into a new
function symbol__disassemble_bpf() in an upcoming patch, where annotation line
information is filled based bpf_prog_info and btf saved in given perf_env.

Committer notes:

Removed the unnamed union with 'bpf_prog' and 'cache' in 'struct dso',
to fix this bug when exiting 'perf top':

  # perf top
  perf: Segmentation fault
  -------- backtrace --------
  perf[0x5a785a]
  /lib64/libc.so.6(+0x385bf)[0x7fd68443c5bf]
  perf(rb_first+0x2b)[0x4d6eeb]
  perf(dso__delete+0xb7)[0x4dffb7]
  perf[0x4f9e37]
  perf(perf_session__delete+0x64)[0x504df4]
  perf(cmd_top+0x1957)[0x454467]
  perf[0x4aad18]
  perf(main+0x61c)[0x42ec7c]
  /lib64/libc.so.6(__libc_start_main+0xf2)[0x7fd684428412]
  perf(_start+0x2d)[0x42eead]
  #
  # addr2line -fe ~/bin/perf 0x4dffb7
  dso_cache__free
  /home/acme/git/perf/tools/perf/util/dso.c:713

That is trying to access the dso->data.cache, and that is not used with
BPF programs, so we end up accessing what is in bpf_prog.first_member,
b00m.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-13-songliubraving@fb.com
[ split from a larger patch ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf feature detection: Add -lopcodes to feature-libbfd

Both libbfd and libopcodes are distributed with binutil-dev/devel. When
libbfd is present, it is OK to assume that libopcodes also present. This
has been a safe assumption for bpftool.

This patch adds -lopcodes to perf/Makefile.config. libopcodes will be
used in the next commit for BPF annotation.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-12-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf top: Add option --no-bpf-event

This patch adds option --no-bpf-event to 'perf top', which is the same
as the option of 'perf record'.

The following patches will use this option.

Committer testing:

  # perf top -vv 2> /tmp/perf_event_attr.out
  # cat  /tmp/perf_event_attr.out
  ------------------------------------------------------------
  perf_event_attr:
    size                             112
    { sample_period, sample_freq }   4000
    sample_type                      IP|TID|TIME|CPU|PERIOD
    read_format                      ID
    disabled                         1
    inherit                          1
    mmap                             1
    comm                             1
    freq                             1
    task                             1
    precise_ip                       3
    sample_id_all                    1
    exclude_guest                    1
    mmap2                            1
    comm_exec                        1
    ksymbol                          1
    bpf_event                        1
  ------------------------------------------------------------
  #

After this patch:

  # perf top --no-bpf-event -vv 2> /tmp/perf_event_attr.out
  # cat  /tmp/perf_event_attr.out
  ------------------------------------------------------------
  perf_event_attr:
    size                             112
    { sample_period, sample_freq }   4000
    sample_type                      IP|TID|TIME|CPU|PERIOD
    read_format                      ID
    disabled                         1
    inherit                          1
    mmap                             1
    comm                             1
    freq                             1
    task                             1
    precise_ip                       3
    sample_id_all                    1
    exclude_guest                    1
    mmap2                            1
    comm_exec                        1
    ksymbol                          1
  ------------------------------------------------------------
  #

Signed-off-by: Song Liu <songliubraving@fb.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-11-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf bpf: Save BTF information as headers to perf.data

This patch enables 'perf record' to save BTF information as headers to
perf.data.

A new header type HEADER_BPF_BTF is introduced for this data.

Committer testing:

As root, being on the kernel sources top level directory, run:

    # perf trace -e tools/perf/examples/bpf/augmented_raw_syscalls.c -e *msg

Just to compile and load a BPF program that attaches to the
raw_syscalls:sys_{enter,exit} tracepoints to trace the syscalls ending
in "msg" (recvmsg, sendmsg, recvmmsg, sendmmsg, etc).

Make sure you have a recent enough clang, say version 9, to get the
BTF ELF sections needed for this testing:

  # clang --version | head -1
  clang version 9.0.0 (https://git.llvm.org/git/clang.git/ 7906282d3afec5dfdc2b27943fd6c0309086c507) (https://git.llvm.org/git/llvm.git/ a1b5de1ff8ae8bc79dc8e86e1f82565229bd0500)
  # readelf -SW tools/perf/examples/bpf/augmented_raw_syscalls.o | grep BTF
    [22] .BTF              PROGBITS        0000000000000000 000ede 000b0e 00      0   0  1
    [23] .BTF.ext          PROGBITS        0000000000000000 0019ec 0002a0 00      0   0  1
    [24] .rel.BTF.ext      REL             0000000000000000 002fa8 000270 10     30  23  8

Then do a systemwide perf record session for a few seconds:

  # perf record -a sleep 2s

Then look at:

  # perf report --header-only | grep b[pt]f
  # event : name = cycles:ppp, , id = { 1116204, 1116205, 1116206, 1116207, 1116208, 1116209, 1116210, 1116211 }, size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|PERIOD, read_format = ID, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, enable_on_exec = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1, ksymbol = 1, bpf_event = 1
  # bpf_prog_info of id 13
  # bpf_prog_info of id 14
  # bpf_prog_info of id 15
  # bpf_prog_info of id 16
  # bpf_prog_info of id 17
  # bpf_prog_info of id 18
  # bpf_prog_info of id 21
  # bpf_prog_info of id 22
  # bpf_prog_info of id 51
  # bpf_prog_info of id 52
  # btf info of id 8
  #

We need to show more info about these BPF and BTF entries , but that can
be done later.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-10-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf bpf: Save BTF in a rbtree in perf_env

BTF contains information necessary to annotate BPF programs. This patch
saves BTF for BPF programs loaded in the system.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-9-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf bpf: Save bpf_prog_info information as headers to perf.data

This patch enables perf-record to save bpf_prog_info information as
headers to perf.data. A new header type HEADER_BPF_PROG_INFO is
introduced for this data.

Committer testing:

As root, being on the kernel sources top level directory, run:

  # perf trace -e tools/perf/examples/bpf/augmented_raw_syscalls.c -e *msg

Just to compile and load a BPF program that attaches to the
raw_syscalls:sys_{enter,exit} tracepoints to trace the syscalls ending
in "msg" (recvmsg, sendmsg, recvmmsg, sendmmsg, etc).

Then do a systemwide perf record session for a few seconds:

  # perf record -a sleep 2s

Then look at:

  # perf report --header-only | grep -i bpf
  # bpf_prog_info of id 13
  # bpf_prog_info of id 14
  # bpf_prog_info of id 15
  # bpf_prog_info of id 16
  # bpf_prog_info of id 17
  # bpf_prog_info of id 18
  # bpf_prog_info of id 21
  # bpf_prog_info of id 22
  # bpf_prog_info of id 208
  # bpf_prog_info of id 209
  #

We need to show more info about these programs, like bpftool does for
the ones running on the system, i.e. 'perf record/perf report' become a
way of saving the BPF state in a machine to then analyse on another,
together with all the other information that is already saved in the
perf.data header:

  # perf report --header-only
  # ========
  # captured on    : Tue Mar 12 11:42:13 2019
  # header version : 1
  # data offset    : 296
  # data size      : 16294184
  # feat offset    : 16294480
  # hostname : quaco
  # os release : 5.0.0+
  # perf version : 5.0.gd783c8
  # arch : x86_64
  # nrcpus online : 8
  # nrcpus avail : 8
  # cpudesc : Intel(R) Core(TM) i7-8650U CPU @ 1.90GHz
  # cpuid : GenuineIntel,6,142,10
  # total memory : 24555720 kB
  # cmdline : /home/acme/bin/perf (deleted) record -a
  # event : name = cycles:ppp, , id = { 3190123, 3190124, 3190125, 3190126, 3190127, 3190128, 3190129, 3190130 }, size = 112, { sample_period, sample_freq } = 4000, sample_type = IP|TID|TIME|CPU|PERIOD, read_format = ID, disabled = 1, inherit = 1, mmap = 1, comm = 1, freq = 1, task = 1, precise_ip = 3, sample_id_all = 1, exclude_guest = 1, mmap2 = 1, comm_exec = 1
  # CPU_TOPOLOGY info available, use -I to display
  # NUMA_TOPOLOGY info available, use -I to display
  # pmu mappings: intel_pt = 8, software = 1, power = 11, uprobe = 7, uncore_imc = 12, cpu = 4, cstate_core = 18, uncore_cbox_2 = 15, breakpoint = 5, uncore_cbox_0 = 13, tracepoint = 2, cstate_pkg = 19, uncore_arb = 17, kprobe = 6, i915 = 10, msr = 9, uncore_cbox_3 = 16, uncore_cbox_1 = 14
  # CACHE info available, use -I to display
  # time of first sample : 116392.441701
  # time of last sample : 116400.932584
  # sample duration :   8490.883 ms
  # MEM_TOPOLOGY info available, use -I to display
  # bpf_prog_info of id 13
  # bpf_prog_info of id 14
  # bpf_prog_info of id 15
  # bpf_prog_info of id 16
  # bpf_prog_info of id 17
  # bpf_prog_info of id 18
  # bpf_prog_info of id 21
  # bpf_prog_info of id 22
  # bpf_prog_info of id 208
  # bpf_prog_info of id 209
  # missing features: TRACING_DATA BRANCH_STACK GROUP_DESC AUXTRACE STAT CLOCKID DIR_FORMAT
  # ========
  #

Committer notes:

We can't use the libbpf unconditionally, as the build may have been with
NO_LIBBPF, when we end up with linking errors, so provide dummy
{process,write}_bpf_prog_info() wrapped by HAVE_LIBBPF_SUPPORT for that
case.

Printing are not affected by this, so can continue as is.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-8-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf bpf: Save bpf_prog_info in a rbtree in perf_env

bpf_prog_info contains information necessary to annotate bpf programs.

This patch saves bpf_prog_info for bpf programs loaded in the system.

Some big picture of the next few patches:

To fully annotate BPF programs with source code mapping, 4 different
informations are needed:

    1) PERF_RECORD_KSYMBOL
    2) PERF_RECORD_BPF_EVENT
    3) bpf_prog_info
    4) btf

Before this set, 1) and 2) in the list are already saved to perf.data
file. For BPF programs that are already loaded before perf run, 1) and 2)
are synthesized by perf_event__synthesize_bpf_events(). For short living
BPF programs, 1) and 2) are generated by kernel.

This set handles 3) and 4) from the list. Again, it is necessary to handle
existing BPF program and short living program separately.

This patch handles 3) for exising BPF programs while synthesizing 1) and
2) in perf_event__synthesize_bpf_events(). These data are stored in
perf_env. The next patch saves these data from perf_env to perf.data as
headers.

Similarly, the two patches after the next saves 4) of existing BPF
programs to perf_env and perf.data.

Another patch later will handle 3) and 4) for short living BPF programs
by monitoring 1) and 2) in a dedicate thread.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-7-songliubraving@fb.com
[ set env->bpf_progs.infos_cnt to zero in perf_env__purge_bpf() as noted by jolsa ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf bpf: Make synthesize_bpf_events() receive perf_session pointer instead of perf_tool

This patch changes the arguments of perf_event__synthesize_bpf_events()
to include perf_session* instead of perf_tool*. perf_session will be
used in the next patch.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: kernel-team@fb.com
Link: http://lkml.kernel.org/r/20190312053051.2690567-6-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf bpf: Synthesize bpf events with bpf_program__get_prog_info_linear()

With bpf_program__get_prog_info_linear, we can simplify the logic that
synthesizes bpf events.

This patch doesn't change the behavior of the code.

Commiter notes:

Needed this (for all four variables), suggested by Song, to overcome
build failure on debian experimental cross building to MIPS 32-bit:

  -               u8 (*prog_tags)[BPF_TAG_SIZE] = (void *)(info->prog_tags);
  +               u8 (*prog_tags)[BPF_TAG_SIZE] = (void *)(uintptr_t)(info->prog_tags);

  util/bpf-event.c: In function 'perf_event__synthesize_one_bpf_prog':
  util/bpf-event.c:143:35: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
     u8 (*prog_tags)[BPF_TAG_SIZE] = (void *)(info->prog_tags);
                                     ^
  util/bpf-event.c:144:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
     __u32 *prog_lens = (__u32 *)(info->jited_func_lens);
                        ^
  util/bpf-event.c:145:23: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
     __u64 *prog_addrs = (__u64 *)(info->jited_ksyms);
                         ^
  util/bpf-event.c:146:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
     void *func_infos = (void *)(info->func_info);
                        ^
  cc1: all warnings being treated as errors

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: kernel-team@fb.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-5-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

bpftool: use bpf_program__get_prog_info_linear() in prog.c:do_dump()

This patches uses bpf_program__get_prog_info_linear() to simplify the
logic in prog.c do_dump().

Committer testing:

Before:

  # bpftool prog dump xlated id 208 > /tmp/dump.xlated.before
  # bpftool prog dump jited id 208 > /tmp/dump.jited.before
  # bpftool map dump id 107 > /tmp/map.dump.before

After:

  # ~acme/git/perf/tools/bpf/bpftool/bpftool map dump id 107 > /tmp/map.dump.after
  # ~acme/git/perf/tools/bpf/bpftool/bpftool prog dump xlated id 208 > /tmp/dump.xlated.after
  # ~acme/git/perf/tools/bpf/bpftool/bpftool prog dump jited id 208 > /tmp/dump.jited.after
  # diff -u /tmp/dump.xlated.before /tmp/dump.xlated.after
  # diff -u /tmp/dump.jited.before /tmp/dump.jited.after
  # diff -u /tmp/map.dump.before /tmp/map.dump.after
  # ~acme/git/perf/tools/bpf/bpftool/bpftool prog dump xlated id 208
     0: (bf) r6 = r1
     1: (85) call bpf_get_current_pid_tgid#80800
     2: (63) *(u32 *)(r10 -328) = r0
     3: (bf) r2 = r10
     4: (07) r2 += -328
     5: (18) r1 = map[id:107]
     7: (85) call __htab_map_lookup_elem#85680
     8: (15) if r0 == 0x0 goto pc+1
     9: (07) r0 += 56
    10: (b7) r7 = 0
    11: (55) if r0 != 0x0 goto pc+52
    12: (bf) r1 = r10
    13: (07) r1 += -328
    14: (b7) r2 = 64
    15: (bf) r3 = r6
    16: (85) call bpf_probe_read#-46848
    17: (bf) r2 = r10
    18: (07) r2 += -320
    19: (18) r1 = map[id:106]
    21: (07) r1 += 208
    22: (61) r0 = *(u32 *)(r2 +0)
    23: (35) if r0 >= 0x200 goto pc+3
    24: (67) r0 <<= 3
    25: (0f) r0 += r1
    26: (05) goto pc+1
    27: (b7) r0 = 0
    28: (15) if r0 == 0x0 goto pc+35
    29: (71) r1 = *(u8 *)(r0 +0)
    30: (15) if r1 == 0x0 goto pc+33
    31: (b7) r5 = 64
    32: (79) r1 = *(u64 *)(r10 -320)
    33: (15) if r1 == 0x2 goto pc+2
    34: (15) if r1 == 0x101 goto pc+3
    35: (55) if r1 != 0x15 goto pc+19
    36: (79) r3 = *(u64 *)(r6 +16)
    37: (05) goto pc+1
    38: (79) r3 = *(u64 *)(r6 +24)
    39: (15) if r3 == 0x0 goto pc+15
    40: (b7) r1 = 0
    41: (63) *(u32 *)(r10 -260) = r1
    42: (bf) r1 = r10
    43: (07) r1 += -256
    44: (b7) r2 = 256
    45: (85) call bpf_probe_read_str#-46704
    46: (b7) r5 = 328
    47: (63) *(u32 *)(r10 -264) = r0
    48: (bf) r1 = r0
    49: (67) r1 <<= 32
    50: (77) r1 >>= 32
    51: (25) if r1 > 0xff goto pc+3
    52: (07) r0 += 72
    53: (57) r0 &= 255
    54: (bf) r5 = r0
    55: (bf) r4 = r10
    56: (07) r4 += -328
    57: (bf) r1 = r6
    58: (18) r2 = map[id:105]
    60: (18) r3 = 0xffffffff
    62: (85) call bpf_perf_event_output_tp#-45104
    63: (bf) r7 = r0
    64: (bf) r0 = r7
    65: (95) exit
  #

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: kernel-team@fb.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-4-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

tools lib bpf: Introduce bpf_program__get_prog_info_linear()

Currently, bpf_prog_info includes 9 arrays. The user has the option to
fetch any combination of these arrays. However, this requires a lot of
handling.

This work becomes more tricky when we need to store bpf_prog_info to a
file, because these arrays are allocated independently.

This patch introduces 'struct bpf_prog_info_linear', which stores arrays
of bpf_prog_info in continuous memory.

Helper functions are introduced to unify the work to get different sets
of bpf_prog_info. Specifically, bpf_program__get_prog_info_linear()
allows the user to select which arrays to fetch, and handles details for
the user.

Please see the comments right before 'enum bpf_prog_info_array' for more
details and examples.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lkml.kernel.org/r/ce92c091-e80d-a0c1-4aa0-987706c42b20@iogearbox.net
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: kernel-team@fb.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-3-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf record: Replace option --bpf-event with --no-bpf-event

Currently, monitoring of BPF programs through bpf_event is off by
default for 'perf record'.

To turn it on, the user need to use option "--bpf-event". As BPF gets
wider adoption in different subsystems, this option becomes
inconvenient.

This patch makes bpf_event on by default, and adds option "--no-bpf-event"
to turn it off. Since option --bpf-event is not released yet, it is safe
to remove it.

Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: kernel-team@fb.com
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Link: http://lkml.kernel.org/r/20190312053051.2690567-2-songliubraving@fb.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tests: Fix a memory leak in test__perf_evsel__tp_sched_test()

  =================================================================
  ==20875==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 1160 byte(s) in 1 object(s) allocated from:
      #0 0x7f1b6fc84138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x55bd50005599 in zalloc util/util.h:23
      #2 0x55bd500068f5 in perf_evsel__newtp_idx util/evsel.c:327
      #3 0x55bd4ff810fc in perf_evsel__newtp /home/work/linux/tools/perf/util/evsel.h:216
      #4 0x55bd4ff81608 in test__perf_evsel__tp_sched_test tests/evsel-tp-sched.c:69
      #5 0x55bd4ff528e6 in run_test tests/builtin-test.c:358
      #6 0x55bd4ff52baf in test_and_print tests/builtin-test.c:388
      #7 0x55bd4ff543fe in __cmd_test tests/builtin-test.c:583
      #8 0x55bd4ff5572f in cmd_test tests/builtin-test.c:722
      #9 0x55bd4ffc4087 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #10 0x55bd4ffc45c6 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #11 0x55bd4ffc49ca in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #12 0x55bd4ffc5138 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #13 0x7f1b6e34809a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

  Indirect leak of 19 byte(s) in 1 object(s) allocated from:
      #0 0x7f1b6fc83f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30)
      #1 0x7f1b6e3ac30f in vasprintf (/lib/x86_64-linux-gnu/libc.so.6+0x8830f)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 6a6cd11d4e57 ("perf test: Add test for the sched tracepoint format fields")
Link: http://lkml.kernel.org/r/20190316080556.3075-17-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tests: Fix memory leak by expr__find_other() in test__expr()

  =================================================================
  ==7506==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 13 byte(s) in 3 object(s) allocated from:
      #0 0x7f03339d6070 in __interceptor_strdup (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x3b070)
      #1 0x5625e53aaef0 in expr__find_other util/expr.y:221
      #2 0x5625e51bcd3f in test__expr tests/expr.c:52
      #3 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #4 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #5 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #6 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #7 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #8 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #9 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #10 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #11 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 075167363f8b ("perf tools: Add a simple expression parser for JSON")
Link: http://lkml.kernel.org/r/20190316080556.3075-16-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tests: Fix a memory leak of cpu_map object in the openat_syscall_event_on_all_cpus test

  =================================================================
  ==7497==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 40 byte(s) in 1 object(s) allocated from:
      #0 0x7f0333a88f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30)
      #1 0x5625e5326213 in cpu_map__trim_new util/cpumap.c:45
      #2 0x5625e5326703 in cpu_map__read util/cpumap.c:103
      #3 0x5625e53267ef in cpu_map__read_all_cpu_map util/cpumap.c:120
      #4 0x5625e5326915 in cpu_map__new util/cpumap.c:135
      #5 0x5625e517b355 in test__openat_syscall_event_on_all_cpus tests/openat-syscall-all-cpus.c:36
      #6 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #7 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #8 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #9 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #10 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #11 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #12 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #13 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #14 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: f30a79b012e5 ("perf tools: Add reference counting for cpu_map object")
Link: http://lkml.kernel.org/r/20190316080556.3075-15-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf evsel: Free evsel->counts in perf_evsel__exit()

Using gcc's ASan, Changbin reports:

  =================================================================
  ==7494==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 48 byte(s) in 1 object(s) allocated from:
      #0 0x7f0333a89138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x5625e5330a5e in zalloc util/util.h:23
      #2 0x5625e5330a9b in perf_counts__new util/counts.c:10
      #3 0x5625e5330ca0 in perf_evsel__alloc_counts util/counts.c:47
      #4 0x5625e520d8e5 in __perf_evsel__read_on_cpu util/evsel.c:1505
      #5 0x5625e517a985 in perf_evsel__read_on_cpu /home/work/linux/tools/perf/util/evsel.h:347
      #6 0x5625e517ad1a in test__openat_syscall_event tests/openat-syscall.c:47
      #7 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #8 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #9 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #10 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #11 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #12 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #13 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #14 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #15 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

  Indirect leak of 72 byte(s) in 1 object(s) allocated from:
      #0 0x7f0333a89138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x5625e532560d in zalloc util/util.h:23
      #2 0x5625e532566b in xyarray__new util/xyarray.c:10
      #3 0x5625e5330aba in perf_counts__new util/counts.c:15
      #4 0x5625e5330ca0 in perf_evsel__alloc_counts util/counts.c:47
      #5 0x5625e520d8e5 in __perf_evsel__read_on_cpu util/evsel.c:1505
      #6 0x5625e517a985 in perf_evsel__read_on_cpu /home/work/linux/tools/perf/util/evsel.h:347
      #7 0x5625e517ad1a in test__openat_syscall_event tests/openat-syscall.c:47
      #8 0x5625e51528e6 in run_test tests/builtin-test.c:358
      #9 0x5625e5152baf in test_and_print tests/builtin-test.c:388
      #10 0x5625e51543fe in __cmd_test tests/builtin-test.c:583
      #11 0x5625e515572f in cmd_test tests/builtin-test.c:722
      #12 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #13 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #14 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #15 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #16 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

His patch took care of evsel->prev_raw_counts, but the above backtraces
are about evsel->counts, so fix that instead.

Reported-by: Changbin Du <changbin.du@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lkml.kernel.org/n/tip-hd1x13g59f0nuhe4anxhsmfp@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf top: Fix global-buffer-overflow issue

The array str[] should have six elements.

  =================================================================
  ==4322==ERROR: AddressSanitizer: global-buffer-overflow on address 0x56463844e300 at pc 0x564637e7ad0d bp 0x7f30c8c89d10 sp 0x7f30c8c89d00
  READ of size 8 at 0x56463844e300 thread T9
      #0 0x564637e7ad0c in __ordered_events__flush util/ordered-events.c:316
      #1 0x564637e7b0e4 in ordered_events__flush util/ordered-events.c:338
      #2 0x564637c6a57d in process_thread /home/changbin/work/linux/tools/perf/builtin-top.c:1073
      #3 0x7f30d173a163 in start_thread (/lib/x86_64-linux-gnu/libpthread.so.0+0x8163)
      #4 0x7f30cfffbdee in __clone (/lib/x86_64-linux-gnu/libc.so.6+0x11adee)

  0x56463844e300 is located 32 bytes to the left of global variable 'flags' defined in 'util/trace-event-parse.c:229:26' (0x56463844e320) of size 192
  0x56463844e300 is located 0 bytes to the right of global variable 'str' defined in 'util/ordered-events.c:268:28' (0x56463844e2e0) of size 32
  SUMMARY: AddressSanitizer: global-buffer-overflow util/ordered-events.c:316 in __ordered_events__flush
  Shadow bytes around the buggy address:
    0x0ac947081c10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081c20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081c30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081c40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081c50: 00 00 00 00 00 00 00 00 f9 f9 f9 f9 00 00 00 00
  =>0x0ac947081c60:[f9]f9 f9 f9 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081c70: 00 00 00 00 00 00 00 00 00 00 00 00 f9 f9 f9 f9
    0x0ac947081c80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081c90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081ca0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
    0x0ac947081cb0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  Shadow byte legend (one shadow byte represents 8 application bytes):
    Addressable:           00
    Partially addressable: 01 02 03 04 05 06 07
    Heap left redzone:       fa
    Freed heap region:       fd
    Stack left redzone:      f1
    Stack mid redzone:       f2
    Stack right redzone:     f3
    Stack after return:      f5
    Stack use after scope:   f8
    Global redzone:          f9
    Global init order:       f6
    Poisoned by user:        f7
    Container overflow:      fc
    Array cookie:            ac
    Intra object redzone:    bb
    ASan internal:           fe
    Left alloca redzone:     ca
    Right alloca redzone:    cb
  Thread T9 created by T0 here:
      #0 0x7f30d179de5f in __interceptor_pthread_create (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x4ae5f)
      #1 0x564637c6b954 in __cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1253
      #2 0x564637c7173c in cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1642
      #3 0x564637d85038 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #4 0x564637d85577 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #5 0x564637d8597b in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #6 0x564637d860e9 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #7 0x7f30cff0509a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Fixes: 16c66bc167cc ("perf top: Add processing thread")
Fixes: 68ca5d07de20 ("perf ordered_events: Add ordered_events__flush_time interface")
Link: http://lkml.kernel.org/r/20190316080556.3075-13-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf maps: Purge all maps from the 'names' tree

Add function __maps__purge_names() to purge all maps from the names
tree. We need to cleanup the names tree in maps__exit().

Detected with gcc's ASan.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 1e6285699b30 ("perf symbols: Fix slowness due to -ffunction-section")
Link: http://lkml.kernel.org/r/20190316080556.3075-12-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf map: Remove map from 'names' tree in __maps__remove()

There are two trees for each map inserted by maps__insert(), so remove
it from the 'names' tree in __maps__remove().

Detected with gcc's ASan.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 1e6285699b30 ("perf symbols: Fix slowness due to -ffunction-section")
Link: http://lkml.kernel.org/r/20190316080556.3075-11-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf hist: Add missing map__put() in error case

We need to map__put() before returning from failure of
sample__resolve_callchain().

Detected with gcc's ASan.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 9c68ae98c6f7 ("perf callchain: Reference count maps")
Link: http://lkml.kernel.org/r/20190316080556.3075-10-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf top: Fix error handling in cmd_top()

We should go to the cleanup path, to avoid leaks, detected using gcc's
ASan.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20190316080556.3075-9-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf top: Delete the evlist before perf_session, fixing heap-use-after-free issue

The evlist should be destroyed before the perf session.

Detected with gcc's ASan:

  =================================================================
  ==27350==ERROR: AddressSanitizer: heap-use-after-free on address 0x62b000002e38 at pc 0x5611da276999 bp 0x7ffce8f1d1a0 sp 0x7ffce8f1d190
  WRITE of size 8 at 0x62b000002e38 thread T0
      #0 0x5611da276998 in __list_del /home/work/linux/tools/include/linux/list.h:89
      #1 0x5611da276d4a in __list_del_entry /home/work/linux/tools/include/linux/list.h:102
      #2 0x5611da276e77 in list_del_init /home/work/linux/tools/include/linux/list.h:145
      #3 0x5611da2781cd in thread__put util/thread.c:130
      #4 0x5611da2cc0a8 in __thread__zput util/thread.h:68
      #5 0x5611da2d2dcb in hist_entry__delete util/hist.c:1148
      #6 0x5611da2cdf91 in hists__delete_entry util/hist.c:337
      #7 0x5611da2ce19e in hists__delete_entries util/hist.c:365
      #8 0x5611da2db2ab in hists__delete_all_entries util/hist.c:2639
      #9 0x5611da2db325 in hists_evsel__exit util/hist.c:2651
      #10 0x5611da1c5352 in perf_evsel__exit util/evsel.c:1304
      #11 0x5611da1c5390 in perf_evsel__delete util/evsel.c:1309
      #12 0x5611da1b35f0 in perf_evlist__purge util/evlist.c:124
      #13 0x5611da1b38e2 in perf_evlist__delete util/evlist.c:148
      #14 0x5611da069781 in cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1645
      #15 0x5611da17d038 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #16 0x5611da17d577 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #17 0x5611da17d97b in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #18 0x5611da17e0e9 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #19 0x7fdcc970f09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)
      #20 0x5611d9ff35c9 in _start (/home/work/linux/tools/perf/perf+0x3e95c9)

  0x62b000002e38 is located 11320 bytes inside of 27448-byte region [0x62b000000200,0x62b000006d38)
  freed by thread T0 here:
      #0 0x7fdccb04ab70 in free (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedb70)
      #1 0x5611da260df4 in perf_session__delete util/session.c:201
      #2 0x5611da063de5 in __cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1300
      #3 0x5611da06973c in cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1642
      #4 0x5611da17d038 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #5 0x5611da17d577 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #6 0x5611da17d97b in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #7 0x5611da17e0e9 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #8 0x7fdcc970f09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

  previously allocated by thread T0 here:
      #0 0x7fdccb04b138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138)
      #1 0x5611da26010c in zalloc util/util.h:23
      #2 0x5611da260824 in perf_session__new util/session.c:118
      #3 0x5611da0633a6 in __cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1192
      #4 0x5611da06973c in cmd_top /home/changbin/work/linux/tools/perf/builtin-top.c:1642
      #5 0x5611da17d038 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #6 0x5611da17d577 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #7 0x5611da17d97b in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #8 0x5611da17e0e9 in main /home/changbin/work/linux/tools/perf/perf.c:520
      #9 0x7fdcc970f09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

  SUMMARY: AddressSanitizer: heap-use-after-free /home/work/linux/tools/include/linux/list.h:89 in __list_del
  Shadow bytes around the buggy address:
    0x0c567fff8570: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff8580: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff8590: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff85a0: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff85b0: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
  =>0x0c567fff85c0: fd fd fd fd fd fd fd[fd]fd fd fd fd fd fd fd fd
    0x0c567fff85d0: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff85e0: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff85f0: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff8600: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
    0x0c567fff8610: fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd fd
  Shadow byte legend (one shadow byte represents 8 application bytes):
    Addressable:           00
    Partially addressable: 01 02 03 04 05 06 07
    Heap left redzone:       fa
    Freed heap region:       fd
    Stack left redzone:      f1
    Stack mid redzone:       f2
    Stack right redzone:     f3
    Stack after return:      f5
    Stack use after scope:   f8
    Global redzone:          f9
    Global init order:       f6
    Poisoned by user:        f7
    Container overflow:      fc
    Array cookie:            ac
    Intra object redzone:    bb
    ASan internal:           fe
    Left alloca redzone:     ca
    Right alloca redzone:    cb
  ==27350==ABORTING

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20190316080556.3075-8-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf build-id: Fix memory leak in print_sdt_events()

Detected with gcc's ASan:

  Direct leak of 4356 byte(s) in 120 object(s) allocated from:
      #0 0x7ff1a2b5a070 in __interceptor_strdup (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x3b070)
      #1 0x55719aef4814 in build_id_cache__origname util/build-id.c:215
      #2 0x55719af649b6 in print_sdt_events util/parse-events.c:2339
      #3 0x55719af66272 in print_events util/parse-events.c:2542
      #4 0x55719ad1ecaa in cmd_list /home/changbin/work/linux/tools/perf/builtin-list.c:58
      #5 0x55719aec745d in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
      #6 0x55719aec7d1a in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
      #7 0x55719aec8184 in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
      #8 0x55719aeca41a in main /home/changbin/work/linux/tools/perf/perf.c:520
      #9 0x7ff1a07ae09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 40218daea1db ("perf list: Show SDT and pre-cached events")
Link: http://lkml.kernel.org/r/20190316080556.3075-7-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf config: Fix a memory leak in collect_config()

Detected with gcc's ASan:

  Direct leak of 66 byte(s) in 5 object(s) allocated from:
      #0 0x7ff3b1f32070 in __interceptor_strdup (/usr/lib/x86_64-linux-gnu/libasan.so.5+0x3b070)
      #1 0x560c8761034d in collect_config util/config.c:597
      #2 0x560c8760d9cb in get_value util/config.c:169
      #3 0x560c8760dfd7 in perf_parse_file util/config.c:285
      #4 0x560c8760e0d2 in perf_config_from_file util/config.c:476
      #5 0x560c876108fd in perf_config_set__init util/config.c:661
      #6 0x560c87610c72 in perf_config_set__new util/config.c:709
      #7 0x560c87610d2f in perf_config__init util/config.c:718
      #8 0x560c87610e5d in perf_config util/config.c:730
      #9 0x560c875ddea0 in main /home/changbin/work/linux/tools/perf/perf.c:442
      #10 0x7ff3afb8609a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Fixes: 20105ca1240c ("perf config: Introduce perf_config_set class")
Link: http://lkml.kernel.org/r/20190316080556.3075-6-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf config: Fix an error in the config template documentation

The option 'sort-order' should be 'sort_order'.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 893c5c798be9 ("perf config: Show default report configuration in example and docs")
Link: http://lkml.kernel.org/r/20190316080556.3075-5-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tools: Fix errors under optimization level '-Og'

Optimization level '-Og' offers a reasonable level of optimization while
maintaining fast compilation and a good debugging experience. This patch
tries to make it work.

  $ make DEBUG=1 EXTRA_CFLAGS='-Og'
  bench/epoll-ctl.c: In function ‘do_threads’:
  bench/epoll-ctl.c:274:9: error: ‘ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
    return ret;
           ^~~
  ...

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20190316080556.3075-4-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf list: Don't forget to drop the reference to the allocated thread_map

Detected via gcc's ASan:

  Direct leak of 2048 byte(s) in 64 object(s) allocated from:
    6     #0 0x7f606512e370 in __interceptor_realloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee370)
    7     #1 0x556b0f1d7ddd in thread_map__realloc util/thread_map.c:43
    8     #2 0x556b0f1d84c7 in thread_map__new_by_tid util/thread_map.c:85
    9     #3 0x556b0f0e045e in is_event_supported util/parse-events.c:2250
   10     #4 0x556b0f0e1aa1 in print_hwcache_events util/parse-events.c:2382
   11     #5 0x556b0f0e3231 in print_events util/parse-events.c:2514
   12     #6 0x556b0ee0a66e in cmd_list /home/changbin/work/linux/tools/perf/builtin-list.c:58
   13     #7 0x556b0f01e0ae in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302
   14     #8 0x556b0f01e859 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354
   15     #9 0x556b0f01edc8 in run_argv /home/changbin/work/linux/tools/perf/perf.c:398
   16     #10 0x556b0f01f71f in main /home/changbin/work/linux/tools/perf/perf.c:520
   17     #11 0x7f6062ccf09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a)

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fixes: 89896051f8da ("perf tools: Do not put a variable sized type not at the end of a struct")
Link: http://lkml.kernel.org/r/20190316080556.3075-3-changbin.du@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf tools: Add doc about how to build perf with Asan and UBSan

AddressSanitizer (or ASan) and UndefinedBehaviorSanitizer (or UBSan) are
very useful tools to detect program bugs:

- AddressSanitizer (or ASan) is a GCC feature that detects memory
   corruption bugs such as buffer overflows and memory leaks.

- UndefinedBehaviorSanitizer (or UBSan) is a fast undefined behavior
   detector supported by GCC. UBSan detects undefined behaviors of programs
   at runtime.

This patch adds a document about how to use them on perf. Later patches will fix
some of the issues disclosed by them.

Signed-off-by: Changbin Du <changbin.du@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20190316080556.3075-2-changbin.du@gmail.com
[ Make some changes based on comments made by Jiri Olsa ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf vendor events: Remove P8 HW events which are not supported

This patch is to remove following hardware events from JSON file which
are not supported on POWER8.

  pm_co_disp_fail
  pm_co_tm_sc_footprint
  pm_iside_disp
  pm_iside_disp_fail
  pm_iside_disp_fail_other
  pm_iside_mru_touch
  pm_l2_castout_mod
  pm_l2_castout_shr
  pm_l2_dc_inv
  pm_l2_disp_all_l2miss
  pm_l2_grp_guess_correct
  pm_l2_grp_guess_wrong
  pm_l2_ic_inv
  pm_l2_inst
  pm_l2_inst_miss
  pm_l2_ld
  pm_l2_ld_disp
  pm_l2_ld_hit
  pm_l2_ld_miss
  pm_l2_loc_guess_correct
  pm_l2_loc_guess_wrong
  pm_l2_rcld_disp
  pm_l2_rcld_disp_fail_addr
  pm_l2_rcld_disp_fail_other
  pm_l2_rcst_disp
  pm_l2_rcst_disp_fail_addr
  pm_l2_rcst_disp_fail_other
  pm_l2_rc_st_done
  pm_l2_rty_ld
  pm_l2_sn_m_rd_done
  pm_l2_sn_m_wr_done
  pm_l2_sn_sx_i_done
  pm_l2_st_disp
  pm_l2_st_hit
  pm_l2_sys_guess_correct
  pm_l2_sys_guess_wrong
  pm_l2_sys_pump
  pm_l3_ci_hit
  pm_l3_ci_miss
  pm_l3_cinj
  pm_l3_co
  pm_l3_co_lco
  pm_l3_grp_guess_correct
  pm_l3_grp_guess_wrong_high
  pm_l3_grp_guess_wrong_low
  pm_l3_hit
  pm_l3_l2_co_hit
  pm_l3_l2_co_miss
  pm_l3_lat_ci_hit
  pm_l3_lat_ci_miss
  pm_l3_ld_hit
  pm_l3_ld_miss
  pm_l3_loc_guess_correct
  pm_l3_loc_guess_wrong
  pm_l3_miss
  pm_l3_p0_co_l31
  pm_l3_p0_co_mem
  pm_l3_p0_co_rty
  pm_l3_p0_grp_pump
  pm_l3_p0_lco_data
  pm_l3_p0_lco_no_data
  pm_l3_p0_lco_rty
  pm_l3_p0_node_pump
  pm_l3_p0_pf_rty
  pm_l3_p0_sn_hit
  pm_l3_p0_sn_inv
  pm_l3_p0_sn_miss
  pm_l3_p0_sys_pump
  pm_l3_p1_co_l31
  pm_l3_p1_co_mem
  pm_l3_p1_co_rty
  pm_l3_p1_grp_pump
  pm_l3_p1_lco_data
  pm_l3_p1_lco_no_data
  pm_l3_p1_lco_rty
  pm_l3_p1_node_pump
  pm_l3_p1_pf_rty
  pm_l3_p1_sn_hit
  pm_l3_p1_sn_inv
  pm_l3_p1_sn_miss
  pm_l3_p1_sys_pump
  pm_l3_pf_hit_l3
  pm_l3_sys_guess_correct
  pm_l3_sys_guess_wrong
  pm_l3_trans_pf
  pm_l3_wi0_busy
  pm_l3_wi_usage
  pm_non_tm_rst_sc
  pm_rd_clearing_sc
  pm_rd_forming_sc
  pm_rd_hit_pf
  pm_snp_tm_hit_m
  pm_snp_tm_hit_t
  pm_st_caused_fail
  pm_tm_cam_overflow
  pm_tm_cap_overflow
  pm_tm_fav_caused_fail
  pm_tm_ld_caused_fail
  pm_tm_ld_conf
  pm_tm_rst_sc
  pm_tm_sc_co
  pm_tm_st_caused_fail
  pm_tm_st_conf

Signed-off-by: Mamatha Inamdar <mamatha4@linux.vnet.ibm.com>
Acked-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Fixes: 2a81fa3bb5ed ("perf vendor events: Add power8 PMU events")
Link: http://lkml.kernel.org/r/154953186583.11022.14819560028300370163.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf stat: Improve scaling

The multiplexing scaling in perf stat mysteriously adds 0.5 to the
value. This dates back to the original perf tool. Other scaling code
doesn't use that strange convention. Remove the extra 0.5.

Before:

$ perf stat -e 'cycles,cycles,cycles,cycles,cycles,cycles' grep -rq foo

Performance counter stats for 'grep -rq foo':

         6,403,580      cycles                                                        (81.62%)
         6,404,341      cycles                                                        (81.64%)
         6,402,983      cycles                                                        (81.62%)
         6,399,941      cycles                                                        (81.63%)
         6,399,451      cycles                                                        (81.62%)
         6,436,105      cycles                                                        (91.87%)

       0.005843799 seconds time elapsed

       0.002905000 seconds user
       0.002902000 seconds sys

After:

$ perf stat -e 'cycles,cycles,cycles,cycles,cycles,cycles' grep -rq foo

Performance counter stats for 'grep -rq foo':

         6,422,704      cycles                                                        (81.68%)
         6,401,842      cycles                                                        (81.68%)
         6,398,432      cycles                                                        (81.68%)
         6,397,098      cycles                                                        (81.68%)
         6,396,074      cycles                                                        (81.67%)
         6,434,980      cycles                                                        (91.62%)

       0.005884437 seconds time elapsed

       0.003580000 seconds user
       0.002356000 seconds sys

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-10-andi@firstfloor.org
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf stat: Fix --no-scale

The -c option to enable multiplex scaling has been useless for quite
some time because scaling is default.

It's only useful as --no-scale to disable scaling. But the non scaling
code path has bitrotted and doesn't print anything because perf output
code relies on value run/ena information.

Also even when we don't want to scale a value it's still useful to show
its multiplex percentage.

This patch:
  - Fixes help and documentation to show --no-scale instead of -c
  - Removes -c, only keeps the long option because -c doesn't support negatives.
  - Enables running/enabled even with --no-scale
  - And fixes some other problems in the no-scale output.

Before:

  $ perf stat --no-scale -e cycles true

   Performance counter stats for 'true':

       <not counted>      cycles

         0.000984154 seconds time elapsed

After:

  $ ./perf stat --no-scale -e cycles true

   Performance counter stats for 'true':

             706,070      cycles

         0.001219821 seconds time elapsed

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
LPU-Reference: 20190314225002.30108-9-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-xggjvwcdaj2aqy8ib3i4b1g6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf script: Support relative time

When comparing time stamps in 'perf script' traces it can be annoying to
work with the full perf time stamps.

Add a --reltime option that displays time stamps relative to the trace
start to make it easier to read the traces.

Note: not currently supported for --time. Report an error in this
case.

Before:

  % perf script
      swapper 0 [000] 245402.891216:    1 cycles:ppp: ffffffffa0068814 native_write_msr+0x4 ([kernel.kallsyms])
      swapper 0 [000] 245402.891223:    1 cycles:ppp: ffffffffa0068814 native_write_msr+0x4 ([kernel.kallsyms])
      swapper 0 [000] 245402.891227:    5 cycles:ppp: ffffffffa0068814 native_write_msr+0x4 ([kernel.kallsyms])
      swapper 0 [000] 245402.891231:   41 cycles:ppp: ffffffffa0068816 native_write_msr+0x6 ([kernel.kallsyms])
      swapper 0 [000] 245402.891235:  355 cycles:ppp: ffffffffa000dd51 intel_bts_enable_local+0x21 ([kernel.kallsyms])
      swapper 0 [000] 245402.891239: 3084 cycles:ppp: ffffffffa0a0150a end_repeat_nmi+0x48 ([kernel.kallsyms])

After:

  % perf script --reltime

      swapper 0 [000]     0.000000:    1 cycles:ppp: ffffffffa0068814 native_write_msr+0x4 ([kernel.kallsyms])
      swapper 0 [000]     0.000006:    1 cycles:ppp: ffffffffa0068814 native_write_msr+0x4 ([kernel.kallsyms])
      swapper 0 [000]     0.000010:    5 cycles:ppp: ffffffffa0068814 native_write_msr+0x4 ([kernel.kallsyms])
      swapper 0 [000]     0.000014:   41 cycles:ppp: ffffffffa0068816 native_write_msr+0x6 ([kernel.kallsyms])
      swapper 0 [000]     0.000018:  355 cycles:ppp: ffffffffa000dd51 intel_bts_enable_local+0x21 ([kernel.kallsyms])
      swapper 0 [000]     0.000022: 3084 cycles:ppp: ffffffffa0a0150a end_repeat_nmi+0x48 ([kernel.kallsyms])

Committer notes:

Do not use 'time' as the name of a variable, as this breaks the build on
older glibcs:

  cc1: warnings being treated as errors
  builtin-script.c: In function 'perf_sample__fprintf_start':
  builtin-script.c:691: warning: declaration of 'time' shadows a global declaration
  /usr/include/time.h:187: warning: shadowed declaration is here

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-8-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-bpahyi6pr9r399mvihu65fvc@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf report: Indicate JITed code better in report

Print [TID] tid %d instead of the crypted /tmp/perf-%d.map default.

% cat >loop.java
  public class loop {
          public static void main(String[] args)
          {
                  for (;;);
          }
  }
  ^D
  % javac loop.java
  % perf record java loop
  ^C

Before:

  % perf report --stdio
  ...
      56.09%  java     perf-34724.map      [.] 0x00007fd5bd021896
      19.12%  java     perf-34724.map      [.] 0x00007fd5bd021887
       9.79%  java     perf-34724.map      [.] 0x00007fd5bd021783
       8.97%  java     perf-34724.map      [.] 0x00007fd5bd02175b

After:

  % perf report --stdio
  ...
      56.09%  java     [JIT] tid 34724     [.] 0x00007fd5bd021896
      19.12%  java     [JIT] tid 34724     [.] 0x00007fd5bd021887
       9.79%  java     [JIT] tid 34724     [.] 0x00007fd5bd021783
       8.97%  java     [JIT] tid 34724     [.] 0x00007fd5bd02175b

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
LPU-Reference: 20190314225002.30108-7-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-r17l6py9g0sezb7mi1f286gt@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf report: Show all sort keys in help output

Show all the supported sort keys in the command line help output, so
that it's not needed to refer to the manpage.

Before:

  % perf report -h
  ...
       -s, --sort <key[,key2...]>
                            sort by key(s): pid, comm, dso, symbol, parent, cpu, srcline, ... Please refer the man page for the complete list.

After:

  % perf report -h
  ...
      -s, --sort <key[,key2...]>
                            sort by key(s): overhead overhead_sys overhead_us overhead_guest_sys overhead_guest_us overhead_children sample period pid comm dso symbol parent cpu ...

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-5-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-9r3uz2ch4izoi1uln3f889co@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf record: Clarify help for --switch-output

The help description for --switch-output looks like there are multiple
comma separated fields. But it's actually a choice of different options.
Make it clear and less confusing.

Before:

  % perf record -h
  ...
          --switch-output[=<signal,size,time>]
                            Switch output when receive SIGUSR2 or cross size,time threshold

After:

  % perf record -h
  ...

          --switch-output[=<signal or size[BKMG] or time[smhd]>]
                            Switch output when receiving SIGUSR2 (signal) or cross a size or time threshold

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-4-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-9yecyuha04nyg8toyd1b2pgi@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

drm/amdgpu: fix invalid use of change_bit

We only need to clear the bit in a 32bit integer.

This fixes a crah on ARM64 and PPC64LE caused by
"drm/amdgpu: update the vm invalidation engine layout V2"

Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: revert "cleanup setting bulk_movable"

This reverts commit 8466cc61da89d33441e0d7a98de1ba98697cd465.

It can trigger a reference counter bug in TTM. Need to investigate further, but
for now revert the offending change.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

scsi: qla2xxx: Fix NULL pointer crash due to stale CPUID

This patch fixes crash due to NULL pointer derefrence because CPU pointer
is not set and used by driver.  Instead, driver is passes CPU as tag via
ha->isp_ops->{lun_reset|target_reset}

[   30.160780] qla2xxx [0000:a0:00.1]-8038:9: Cable is unplugged...
[   69.984045] qla2xxx [0000:a0:00.0]-8009:8: DEVICE RESET ISSUED nexus=8:0:0 cmd=00000000b0d62f46.
[   69.992849] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[   70.000680] PGD 0 P4D 0
[   70.003232] Oops: 0000 [#1] SMP PTI
[   70.006727] CPU: 2 PID: 6714 Comm: sg_reset Kdump: loaded Not tainted 4.18.0-67.el8.x86_64 #1
[   70.015258] Hardware name: NEC Express5800/T110j [N8100-2758Y]/MX32-PH0-NJ, BIOS F11 02/13/2019
[   70.024016] RIP: 0010:blk_mq_rq_cpu+0x9/0x10
[   70.028315] Code: 01 58 01 00 00 48 83 c0 28 48 3d 80 02 00 00 75 ab c3 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48
8b 47 08 <8b> 40 40 c3 0f 1f 00 0f 1f 44 00 00 48 83 ec 10 48 c7 c6 20 6e 7c
[   70.047087] RSP: 0018:ffff99a481487d58 EFLAGS: 00010246
[   70.052322] RAX: 0000000000000000 RBX: ffffffffc041b08b RCX: 0000000000000000
[   70.059466] RDX: 0000000000000000 RSI: ffff8d10b6b16898 RDI: ffff8d10b341e400
[   70.066615] RBP: ffffffffc03a6bd0 R08: 0000000000000415 R09: 0000000000aaaaaa
[   70.073765] R10: 0000000000000001 R11: 0000000000000001 R12: ffff8d10b341e528
[   70.080914] R13: ffff8d10aadefc00 R14: ffff8d0f64efa998 R15: ffff8d0f64efa000
[   70.088083] FS:  00007f90a201e540(0000) GS:ffff8d10b6b00000(0000) knlGS:0000000000000000
[   70.096188] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   70.101959] CR2: 0000000000000040 CR3: 0000000268886005 CR4: 00000000003606e0
[   70.109127] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   70.116277] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   70.123425] Call Trace:
[   70.125896]  __qla2xxx_eh_generic_reset+0xb1/0x220 [qla2xxx]
[   70.131572]  scsi_ioctl_reset+0x1f5/0x2a0
[   70.135600]  scsi_ioctl+0x18e/0x397
[   70.139099]  ? sd_ioctl+0x7c/0x100 [sd_mod]
[   70.143287]  blkdev_ioctl+0x32b/0x9f0
[   70.146954]  ? __check_object_size+0xa3/0x181
[   70.151323]  block_ioctl+0x39/0x40
[   70.154735]  do_vfs_ioctl+0xa4/0x630
[   70.158322]  ? syscall_trace_enter+0x1d3/0x2c0
[   70.162769]  ksys_ioctl+0x60/0x90
[   70.166104]  __x64_sys_ioctl+0x16/0x20
[   70.169859]  do_syscall_64+0x5b/0x1b0
[   70.173532]  entry_SYSCALL_64_after_hwframe+0x65/0xca
[   70.178587] RIP: 0033:0x7f90a1b3445b
[   70.182183] Code: 0f 1e fa 48 8b 05 2d aa 2c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00
00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d fd a9 2c 00 f7 d8 64 89 01 48
[   70.200956] RSP: 002b:00007fffdca88b68 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[   70.208535] RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f90a1b3445b
[   70.215684] RDX: 00007fffdca88b84 RSI: 0000000000002284 RDI: 0000000000000003
[   70.222833] RBP: 00007fffdca88ca8 R08: 00007fffdca88b84 R09: 0000000000000000
[   70.229981] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffdca88b84
[   70.237131] R13: 0000000000000000 R14: 000055ab09b0bd28 R15: 0000000000000000
[   70.244284] Modules linked in: nft_chain_route_ipv4 xt_CHECKSUM nft_chain_nat_ipv4 ipt_MASQUERADE nf_nat_ipv4 nf_nat nf_conntrack_ipv4
nf_defrag_ipv4 xt_conntrack nf_conntrack libcrc32c ipt_REJECT nf_reject_ipv4 nft_counter nft_compat tun bridge stp llc nf_tables nfnetli
nk devlink sunrpc vfat fat intel_rapl intel_pmc_core x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm wmi_bmof iTCO_wdt iTCO_
vendor_support irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ipmi_ssif intel_cstate intel_uncore intel_rapl_perf ipmi_si jo
ydev pcspkr ipmi_devintf sg wmi ipmi_msghandler video acpi_power_meter acpi_pad mei_me i2c_i801 mei ip_tables ext4 mbcache jbd2 sr_mod cd
rom sd_mod qla2xxx ast i2c_algo_bit drm_kms_helper nvme_fc syscopyarea sysfillrect uas sysimgblt fb_sys_fops nvme_fabrics ttm
[   70.314805]  usb_storage nvme_core crc32c_intel scsi_transport_fc ahci drm libahci tg3 libata megaraid_sas pinctrl_cannonlake pinctrl_
intel
[   70.327335] CR2: 0000000000000040

Fixes: 9cf2bab630765 ("block: kill request ->cpu member")
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Fix FC-AL connection target discovery

Commit 7f147f9bfd44 ("scsi: qla2xxx: Fix N2N target discovery with Local
loop") fixed N2N target discovery for local loop. However, same code is
used for FC-AL discovery as well. Added check to make sure we are bypassing
area and domain check only in N2N topology for target discovery.

Fixes: 7f147f9bfd44 ("scsi: qla2xxx: Fix N2N target discovery with Local loop")
Cc: stable@vger.kernel.org # 5.0+
Signed-off-by: Quinn Tran <qtran@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Merge tag 'tag-chrome-platform-fixes-for-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome platform fixes from Benson Leung:
"Two fixes:

   - Fix locking and close a potential race condition in the new
     wilco_ec driver.

   - Fix a warning in cros_ec_debugfs on systems that do not support
     console logging, such as the Asus C201"

* tag 'tag-chrome-platform-fixes-for-v5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: cros_ec_debugfs: cancel/schedule logging work only if supported
  platform/chrome: Fix locking pattern in wilco_ec_mailbox()

scsi: core: Avoid that a kernel warning appears during system resume

Since scsi_device_quiesce() skips SCSI devices that have another state than
RUNNING, OFFLINE or TRANSPORT_OFFLINE, scsi_device_resume() should not
complain about SCSI devices that have been skipped. Hence this patch. This
patch avoids that the following warning appears during resume:

WARNING: CPU: 3 PID: 1039 at blk_clear_pm_only+0x2a/0x30
CPU: 3 PID: 1039 Comm: kworker/u8:49 Not tainted 5.0.0+ #1
Hardware name: LENOVO 4180F42/4180F42, BIOS 83ET75WW (1.45 ) 05/10/2013
Workqueue: events_unbound async_run_entry_fn
RIP: 0010:blk_clear_pm_only+0x2a/0x30
Call Trace:
? scsi_device_resume+0x28/0x50
? scsi_dev_type_resume+0x2b/0x80
? async_run_entry_fn+0x2c/0xd0
? process_one_work+0x1f0/0x3f0
? worker_thread+0x28/0x3c0
? process_one_work+0x3f0/0x3f0
? kthread+0x10c/0x130
? __kthread_create_on_node+0x150/0x150
? ret_from_fork+0x1f/0x30

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Martin Steigerwald <martin@lichtvoll.de>
Cc: <stable@vger.kernel.org>
Reported-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Tested-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: Also call destroy_rcu_head() for passthrough requests

cmd->rcu is initialized by scsi_initialize_rq(). For passthrough
requests, blk_get_request() calls scsi_initialize_rq(). For filesystem
requests, scsi_init_command() calls scsi_initialize_rq(). Make sure
that destroy_rcu_head() is called for passthrough requests.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

platform/chrome: cros_ec_debugfs: cancel/schedule logging work only if supported

The following traceback was reported on ASUS C201, which does not support
console logging.

------------[ cut here ]------------
WARNING: CPU: 2 PID: 361 at kernel/workqueue.c:3030 __flush_work+0x38/0x154
Modules linked in: snd_soc_hdmi_codec cros_ec_debugfs cros_ec_sysfs uvcvideo dw_hdmi_cec dw_hdmi_i2s_audio videobuf2_vmalloc cfg80211 gpio_charger rk_crypto rfkill videobuf2_memops videobuf2_v4l2 des_generic videobuf2_common ofpart m25p80 spi_nor tpm_i2c_infineon sbs_battery mtd tpm joydev cros_ec_dev coreboot_table evdev mousedev ip_tables x_tables [last unloaded: brcmutil]
CPU: 2 PID: 361 Comm: systemd-sleep Not tainted 5.1.0-rc1-1-ARCH+ #1
Hardware name: Rockchip (Device Tree)
[<c020e4b0>] (unwind_backtrace) from [<c020ac18>] (show_stack+0x10/0x14)
[<c020ac18>] (show_stack) from [<c07a3e04>] (dump_stack+0x7c/0x9c)
[<c07a3e04>] (dump_stack) from [<c0222748>] (__warn+0xd0/0xec)
[<c0222748>] (__warn) from [<c022279c>] (warn_slowpath_null+0x38/0x44)
[<c022279c>] (warn_slowpath_null) from [<c02365d0>] (__flush_work+0x38/0x154)
[<c02365d0>] (__flush_work) from [<c023786c>] (__cancel_work_timer+0x114/0x1a4)
[<c023786c>] (__cancel_work_timer) from [<bf33233c>] (cros_ec_debugfs_suspend+0x14/0x1c [cros_ec_debugfs])
[<bf33233c>] (cros_ec_debugfs_suspend [cros_ec_debugfs]) from [<c056a888>] (dpm_run_callback+0x64/0xcc)
[<c056a888>] (dpm_run_callback) from [<c056ad2c>] (__device_suspend+0x174/0x3a8)
[<c056ad2c>] (__device_suspend) from [<c056b9e0>] (dpm_suspend+0x174/0x1e0)
[<c056b9e0>] (dpm_suspend) from [<c026b3e0>] (suspend_devices_and_enter+0x6c/0x50c)
[<c026b3e0>] (suspend_devices_and_enter) from [<c026ba8c>] (pm_suspend+0x20c/0x274)
[<c026ba8c>] (pm_suspend) from [<c026a628>] (state_store+0x54/0x88)
[<c026a628>] (state_store) from [<c03cd2d0>] (kernfs_fop_write+0x114/0x180)
[<c03cd2d0>] (kernfs_fop_write) from [<c035d48c>] (__vfs_write+0x1c/0x154)
[<c035d48c>] (__vfs_write) from [<c035f9e8>] (vfs_write+0xb8/0x198)
[<c035f9e8>] (vfs_write) from [<c035fbc0>] (ksys_write+0x3c/0x74)
[<c035fbc0>] (ksys_write) from [<c0201000>] (ret_fast_syscall+0x0/0x4c)
Exception stack(0xe9365fa8 to 0xe9365ff0)
5fa0: 00000004 beef8b28 00000004 beef8b28 00000004 00000000
5fc0: 00000004 beef8b28 02319170 00000004 beef8b28 00000004 b6f3d900 beef8b74
5fe0: 0000006c beef8a98 b6c0adac b6c66534
---[ end trace f4ee5df14e8ea0ec ]---

If console logging is not supported, the work structure is never
initialized, resulting in the traceback. Calling cancel/schedule functions
conditionally fixes the problem.

While at it, also fix error handling in the probe function.

Reported-by: Urja Rannikko <urjaman@gmail.com>
Cc: Urja Rannikko <urjaman@gmail.com>
Fixes: 6fce0a2cf5a05 ("mfd / platform: cros_ec: Move debugfs attributes to its own driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benson Leung <bleung@chromium.org>

Merge tag 'mips_fixes_5.1_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

Pull MIPS fixes from Paul Burton:
"A small batch of MIPS fixes for 5.1:

   - An interrupt masking fix for Loongson-based Lemote 2F systems
     (fixing a regression from v3.19)

   - A relocation fix for configurations in which the devicetree is
     stored in an ELF section (fixing a regression from v4.7)

   - Fix jump labels for MIPSr6 kernels where they previously could
     inadvertently place a control transfer instruction in a forbidden
     slot & take unexpected exceptions (fixing MIPSr6 support added in
     v4.0)

   - Extend an existing USB power workaround for the Netgear WNDR3400 to
     v2 boards in addition to the v3 ones that already used it

   - Remove the custom MIPS32 definition of __kernel_fsid_t to make it
     consistent with MIPS64 & every other architecture, in particular
     resolving issues for code which tries to print the val field whose
     type previously differed (though had identical memory layout)"

* tag 'mips_fixes_5.1_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: Remove custom MIPS32 __kernel_fsid_t type
  mips: bcm47xx: Enable USB power on Netgear WNDR3400v2
  MIPS: Fix kernel crash for R6 in jump label branch function
  MIPS: Ensure ELF appended dtb is relocated
  mips: loongson64: lemote-2f: Add IRQF_NO_SUSPEND to "cascade" irqaction.

tools/power turbostat: return the exit status of a command

turbostat failed to return a non-zero exit status even though the
supplied command (turbostat <command>) failed. Currently when turbostat
forks a command it returns zero instead of the actual exit status of the
command. Modify the code to return the exit status.

Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

drivers: base: swnode: Make two functions static

Fix sparse warning:

drivers/base/swnode.c:475:22: warning: symbol 'software_node_get_parent' was not declared. Should it be static?
drivers/base/swnode.c:484:22: warning: symbol 'software_node_get_next_child' was not declared. Should it be static?

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

blk-mq: remove unused 'nr_expired' from blk_mq_hw_ctx

There is no usage of 'nr_expired'.

The 'nr_expired' was introduced by commit 1d9bd5161ba3 ("blk-mq: replace
timeout synchronization with a RCU and generation based scheme"). Its usage
was removed since commit 12f5b9314545 ("blk-mq: Remove generation
seqeunce").

Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

perf record: Allow to limit number of reported perf.data files

When doing long term recording and waiting for some event to snapshot
on, we often only care about the last minute or so.

The --switch-output command line option supports rotating the perf.data
file when the size exceeds a threshold. But the disk would still be
filled with unnecessary old files.

Add a new option to only keep a number of rotated files, so that the
disk space usage can be limited.

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-3-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-y5u2lik0ragt4vlktz6qc9ks@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf list: Filter metrics too

When a filter is specified on the command line, filter the metrics too.

Before:

  % perf list foo
  List of pre-defined events (to be used in -e):

  Metric Groups:

  DSB:
    DSB_Coverage
         [Fraction of Uops delivered by the DSB (aka Decoded Icache; or Uop Cache)]
  ... more metrics ...

After:

% perf list foo

  List of pre-defined events (to be used in -e):

  Metric Groups:

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20190314225002.30108-1-andi@firstfloor.org
Link: https://lkml.kernel.org/n/tip-1y8oi2s8c4jhjtykgs5zvda1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

arm64: kpti: Whitelist HiSilicon Taishan v110 CPUs

HiSilicon Taishan v110 CPUs didn't implement CSV3 field of the
ID_AA64PFR0_EL1 and are not susceptible to Meltdown, so whitelist
the MIDR in kpti_safe_list[] table.

Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: Add MIDR encoding for HiSilicon Taishan CPUs

Adding the MIDR encodings for HiSilicon Taishan v110 CPUs,
which is used in Kunpeng ARM64 server SoCs. TSV110 is the
abbreviation of Taishan v110.

Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64/stacktrace: Export save_stack_trace_regs()

The ARM64 implements the save_stack_trace_regs function, but it is
unusable for any diagnostic tooling compiled as a kernel module due
the missing EXPORT_SYMBOL_GPL for the function. Export
save_stack_trace_regs() to align with other architectures such as
s390, openrisc, and powerpc. This is similar to the ARM64 export of
save_stack_trace_tsk() added in git commit e27c7fa015d6.

Signed-off-by: William Cohen <wcohen@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: apply workaround on A64FX v1r0

Fujitsu erratum 010001 applies to A64FX v0r0 and v1r0, and we try to
handle either by masking MIDR with MIDR_FUJITSU_ERRATUM_010001_MASK
before comparing it to MIDR_FUJITSU_ERRATUM_010001.

Unfortunately, MIDR_FUJITSU_ERRATUM_010001 is constructed incorrectly
using MIDR_VARIANT(), which is intended to extract the variant field
from MIDR_EL1, rather than generate the field in-place. This results in
MIDR_FUJITSU_ERRATUM_010001 being all-ones, and we only match A64FX
v0r0.

This patch uses MIDR_CPU_VAR_REV() to generate an in-place mask for the
variant field, ensuring the we match both v0r0 and v1r0.

Fixes: 3e32131abc311a5c ("arm64: Add workaround for Fujitsu A64FX erratum 010001")
Reported-by: "Okamoto, Takayuki" <tokamoto@jp.fujitsu.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: fixed the patch author]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: kprobes: Use arch_populate_kprobe_blacklist()

Use arch_populate_kprobe_blacklist() instead of
arch_within_kprobe_blacklist() so that we can see the full
blacklisted symbols under the debugfs.

Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[catalin.marinas@arm.com: Add arch_populate_kprobe_blacklist() comment]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: kprobes: Move exception_text check in blacklist

Move exception/irqentry text address check in blacklist,
since those are symbol based rejection.

If we prohibit probing on the symbols in exception_text,
those should be blacklisted.

Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: kprobes: Remove unneeded RODATA check

Remove unneeded RODATA check from arch_prepare_kprobe().

Since check_kprobe_address_safe() already ensured that
the probe address is in kernel text, we don't need to
check whether the address in RODATA or not. That must
be always false.

Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

arm64: kprobes: Move extable address check into arch_prepare_kprobe()

Move extable address check into arch_prepare_kprobe() from
arch_within_kprobe_blacklist().
The blacklist is exposed via debugfs as a list of symbols.
The extable entries are smaller, so must be filtered out
by arch_prepare_kprobe().

Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

x86/mm: Don't leak kernel addresses

Since commit:

  ad67b74d2469d9b8 ("printk: hash addresses printed with %p")

at boot "____ptrval____" is printed instead of actual addresses:

    found SMP MP-table at [mem 0x000f5cc0-0x000f5ccf] mapped at [(____ptrval____)]

Instead of changing the print to "%px", and leaking a kernel addresses,
just remove the print completely, like in:

  071929dbdd865f77 ("arm64: Stop printing the virtual memory layout").

Signed-off-by: Matteo Croce <mcroce@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/fair: Skip LLC NOHZ logic for asymmetric systems

The LLC NOHZ condition will become true as soon as >=2 CPUs in a
single LLC domain are busy. On big.LITTLE systems, this translates to
two or more CPUs of a "cluster" (big or LITTLE) being busy.

Issuing a NOHZ kick in these conditions isn't desired for asymmetric
systems, as if the busy CPUs can provide enough compute capacity to
the running tasks, then we can leave the NOHZ CPUs in peace.

Skip the LLC NOHZ condition for asymmetric systems, and rely on
nr_running & capacity checks to trigger NOHZ kicks when the system
actually needs them.

Suggested-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dietmar.Eggemann@arm.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: vincent.guittot@linaro.org
Link: https://lkml.kernel.org/r/20190211175946.4961-4-valentin.schneider@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/fair: Tune down misfit NOHZ kicks

In this commit:

3b1baa6496e6 ("sched/fair: Add 'group_misfit_task' load-balance type")

we set rq->misfit_task_load whenever the current running task has a
utilization greater than 80% of rq->cpu_capacity. A non-zero value in
this field enables misfit load balancing.

However, if the task being looked at is already running on a CPU of
highest capacity, there's nothing more we can do for it. We can
currently spot this in update_sd_pick_busiest(), which prevents us
from selecting a sched_group of group_type == group_misfit_task as the
busiest group, but we don't do any of that in nohz_balancer_kick().

This means that we could repeatedly kick NOHZ CPUs when there's no
improvements in terms of load balance to be done.

Introduce a check_misfit_status() helper that returns true iff there
is a CPU in the system that could give more CPU capacity to a rq's
misfit task - IOW, there exists a CPU of higher capacity_orig or the
rq's CPU is severely pressured by rt/IRQ.

Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dietmar.Eggemann@arm.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: morten.rasmussen@arm.com
Cc: vincent.guittot@linaro.org
Link: https://lkml.kernel.org/r/20190211175946.4961-3-valentin.schneider@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/fair: Comment some nohz_balancer_kick() kick conditions

We now have a comment explaining the first sched_domain based NOHZ kick,
so might as well comment them all.

While at it, unwrap a line that fits under 80 characters.

Co-authored-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dietmar.Eggemann@arm.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: morten.rasmussen@arm.com
Cc: vincent.guittot@linaro.org
Link: https://lkml.kernel.org/r/20190211175946.4961-2-valentin.schneider@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/core: Fix buffer overflow in cgroup2 property cpu.max

Add limit into sscanf format string for on-stack buffer.

Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 0d5936344f30 ("sched: Implement interface for cgroup unified hierarchy")
Link: https://lkml.kernel.org/r/155189230232.2620.13120481613524200065.stgit@buzz
Signed-off-by: Ingo Molnar <mingo@kernel.org>

sched/cpufreq: Fix 32-bit math overflow

Vincent Wang reported that get_next_freq() has a mult overflow bug on
32-bit platforms in the IOWAIT boost case, since in that case {util,max}
are in freq units instead of capacity units.

Solve this by moving the IOWAIT boost to capacity units. And since this
means @max is constant; simplify the code.

Reported-by: Vincent Wang <vincent.wang@unisoc.com>
Tested-by: Vincent Wang <vincent.wang@unisoc.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190305083202.GU32494@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>

fanotify: Allow copying of file handle to userspace

When file handle is embedded inside fanotify_event and usercopy checks
are enabled, we get a warning like:

Bad or missing usercopy whitelist? Kernel memory exposure attempt detected
from SLAB object 'fanotify_event' (offset 40, size 8)!
WARNING: CPU: 1 PID: 7649 at mm/usercopy.c:78 usercopy_warn+0xeb/0x110
mm/usercopy.c:78

Annotate handling in fanotify_event properly to mark copying it to
userspace is fine.

Reported-by: syzbot+2c49971e251e36216d1f@syzkaller.appspotmail.com
Fixes: a8b13aa20afb ("fanotify: enable FAN_REPORT_FID init flag")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>

ALSA: hda - Enforces runtime_resume after S3 and S4 for each codec

Recently we found the audio jack detection stop working after suspend
on many machines with Realtek codec. Sometimes the audio selection
dialogue didn't show up after users plugged headhphone/headset into
the headset jack, sometimes after uses plugged headphone/headset, then
click the sound icon on the upper-right corner of gnome-desktop, it
also showed the speaker rather than the headphone.

The root cause is that before suspend, the codec already call the
runtime_suspend since this codec is not used by any apps, then in
resume, it will not call runtime_resume for this codec. But for some
realtek codec (so far, alc236, alc255 and alc891) with the specific
BIOS, if it doesn't run runtime_resume after suspend, all codec
functions including jack detection stop working anymore.

This problem existed for a long time, but it was not exposed, that is
because when problem happens, if users play sound or open
sound-setting to check audio device, this will trigger calling to
runtime_resume (via snd_hda_power_up), then the codec starts working
again before users notice this problem.

Since we don't know how many codec and BIOS combinations have this
problem, to fix it, let the driver call runtime_resume for all codecs
in pm_resume, maybe for some codecs, this is not needed, but it is
harmless. After a codec is runtime resumed, if it is not used by any
apps, it will be runtime suspended soon and furthermore we don't run
suspend frequently, this change will not add much power consumption.

Fixes: cc72da7d4d06 ("ALSA: hda - Use standard runtime PM for codec power-save control")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: hda - Don't trigger jackpoll_work in azx_resume

The commit 3baffc4a84d7 (ALSA: hda/intel: Refactoring PM code) changed
the behaviour of azx_resume(), it triggers the jackpoll_work after
applying this commit.

This change introduced a new issue, all codecs are runtime active
after S3, and will not call runtime_suspend() automatically.

The root cause is the jackpoll_work calls snd_hda_power_up/down_pm,
and it calls up_pm before snd_hdac_enter_pm is called, while calls
the down_pm in the middle of enter_pm and leave_pm is called. This
makes the dev->power.usage_count unbalanced after S3.

To fix it, let azx_resume() don't trigger jackpoll_work as before
it did.

Fixes: 3baffc4a84d7 ("ALSA: hda/intel: Refactoring PM code")
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

drm/i915: Sanity check mmap length against object size

We assumed that vm_mmap() would reject an attempt to mmap past the end of
the filp (our object), but we were wrong.

Applications that tried to use the mmap beyond the end of the object
would be greeted by a SIGBUS. After this patch, those applications will
be told about the error on creating the mmap, rather than at a random
moment on later access.

Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Testcase: igt/gem_mmap/bad-size
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190314075829.16838-1-chris@chris-wilson.co.uk
(cherry picked from commit 794a11cb67201ad1bb61af510bb8460280feb3f3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Fix off-by-one in reporting hanging process

ffs() is 1-indexed, but we want to use it as an index into an array, so
use __ffs() instead.

Fixes: eb8d0f5af4ec ("drm/i915: Remove GPU reset dependence on struct_mutex")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190315163933.19352-1-chris@chris-wilson.co.uk
(cherry picked from commit 9073e5b26743b8b675cc44a9c0c8f8c3d584e1c0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/bios: assume eDP is present on port A when there is no VBT

We rely on VBT DDI port info for eDP detection on GEN9 platforms and
above. This breaks GEN9 platforms which don't have VBT because port A
eDP now defaults to false. Fix this by defaulting to true when VBT is
missing.

Fixes: a98d9c1d7e9b ("drm/i915/ddi: Rely on VBT DDI port info for eDP detection")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190306200618.17405-1-thomas.preston@codethink.co.uk
(cherry picked from commit 2131bc0ced6088648e47f126566c3da58b07e4ef)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

scsi: iscsi: flush running unbind operations when removing a session

In some cases, the iscsi_remove_session() function is called while an
unbind_work operation is still running.  This may cause a situation where
sysfs objects are removed in an incorrect order, triggering a kernel
warning.

[  605.249442] ------------[ cut here ]------------
[  605.259180] sysfs group 'power' not found for kobject 'target2:0:0'
[  605.321371] WARNING: CPU: 1 PID: 26794 at fs/sysfs/group.c:235 sysfs_remove_group+0x76/0x80
[  605.341266] Modules linked in: dm_service_time target_core_user target_core_pscsi target_core_file target_core_iblock iscsi_target_mod target_core_mod nls_utf8 isofs ppdev bochs_drm nfit ttm libnvdimm drm_kms_helper syscopyarea sysfillrect sysimgblt joydev pcspkr fb_sys_fops drm i2c_piix4 sg parport_pc parport xfs libcrc32c dm_multipath sr_mod sd_mod cdrom ata_generic 8021q garp mrp ata_piix stp crct10dif_pclmul crc32_pclmul llc libata crc32c_intel virtio_net net_failover ghash_clmulni_intel serio_raw failover sunrpc dm_mirror dm_region_hash dm_log dm_mod be2iscsi bnx2i cnic uio cxgb4i cxgb4 libcxgbi libcxgb qla4xxx iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi
[  605.627479] CPU: 1 PID: 26794 Comm: kworker/u32:2 Not tainted 4.18.0-60.el8.x86_64 #1
[  605.721401] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20180724_192412-buildhw-07.phx2.fedoraproject.org-1.fc29 04/01/2014
[  605.823651] Workqueue: scsi_wq_2 __iscsi_unbind_session [scsi_transport_iscsi]
[  605.830940] RIP: 0010:sysfs_remove_group+0x76/0x80
[  605.922907] Code: 48 89 df 5b 5d 41 5c e9 38 c4 ff ff 48 89 df e8 e0 bf ff ff eb cb 49 8b 14 24 48 8b 75 00 48 c7 c7 38 73 cb a7 e8 24 77 d7 ff <0f> 0b 5b 5d 41 5c c3 0f 1f 00 0f 1f 44 00 00 41 56 41 55 41 54 55
[  606.122304] RSP: 0018:ffffbadcc8d1bda8 EFLAGS: 00010286
[  606.218492] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[  606.326381] RDX: ffff98bdfe85eb40 RSI: ffff98bdfe856818 RDI: ffff98bdfe856818
[  606.514498] RBP: ffffffffa7ab73e0 R08: 0000000000000268 R09: 0000000000000007
[  606.529469] R10: 0000000000000000 R11: ffffffffa860d9ad R12: ffff98bdf978e838
[  606.630535] R13: ffff98bdc2cd4010 R14: ffff98bdc2cd3ff0 R15: ffff98bdc2cd4000
[  606.824707] FS:  0000000000000000(0000) GS:ffff98bdfe840000(0000) knlGS:0000000000000000
[  607.018333] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  607.117844] CR2: 00007f84b78ac024 CR3: 000000002c00a003 CR4: 00000000003606e0
[  607.117844] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  607.420926] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  607.524236] Call Trace:
[  607.530591]  device_del+0x56/0x350
[  607.624393]  ? ata_tlink_match+0x30/0x30 [libata]
[  607.727805]  ? attribute_container_device_trigger+0xb4/0xf0
[  607.829911]  scsi_target_reap_ref_release+0x39/0x50
[  607.928572]  scsi_remove_target+0x1a2/0x1d0
[  608.017350]  __iscsi_unbind_session+0xb3/0x160 [scsi_transport_iscsi]
[  608.117435]  process_one_work+0x1a7/0x360
[  608.132917]  worker_thread+0x30/0x390
[  608.222900]  ? pwq_unbound_release_workfn+0xd0/0xd0
[  608.323989]  kthread+0x112/0x130
[  608.418318]  ? kthread_bind+0x30/0x30
[  608.513821]  ret_from_fork+0x35/0x40
[  608.613909] ---[ end trace 0b98c310c8a6138c ]---

Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

rbd: set io_min, io_opt and discard_granularity to alloc_size

Now that we have alloc_size that controls our discard behavior, it
doesn't make sense to have these set to object (set) size. alloc_size
defaults to 64k, but because discard_granularity is likely 4M, only
ranges that are equal to or bigger than 4M can be considered during
fstrim. A smaller io_min is also more likely to be met, resulting in
fewer deferred writes on bluestore OSDs.

Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>

platform/chrome: Fix locking pattern in wilco_ec_mailbox()

Before, ec->data_buffer could be written to from multiple
contexts at the same time. Since the ec is shared data,
it needs to be inside the mutex as well.

Fixes: 7b3d4f44abf0 ("platform/chrome: Add new driver for Wilco EC")
Signed-off-by: Nick Crews <ncrews@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>

Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma

Pull rdma fixes from Jason Gunthorpe:
"Several driver bug fixes post in the last three weeks

   - first part of a race condition fix in mlx4 with CATAS errors

   - bad interaction with FW causing resource leaks in the mlx5 DCT flow

   - bad reporting of link speed/width in new mlx5 devices

   - user triggable OOPS in i40iw"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  i40iw: Avoid panic when handling the inetdev event
  IB/mlx5: Fix mapping of link-mode to IB width and speed
  IB/mlx5: Use mlx5 core to create/destroy a DEVX DCT
  net/mlx5: Fix DCT creation bad flow
  IB/mlx4: Fix race condition between catas error reset and aliasguid flows

block: add BIO_NO_PAGE_REF flag

If bio_iov_iter_get_pages() is called on an iov_iter that is flagged
with NO_REF, then we don't need to add a page reference for the pages
that we add.

Add BIO_NO_PAGE_REF to track this in the bio, so IO completion knows
not to drop a reference to these pages.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

iov_iter: add ITER_BVEC_FLAG_NO_REF flag

For ITER_BVEC, if we're holding on to kernel pages, the caller
doesn't need to grab a reference to the bvec pages, and drop that
same reference on IO completion. This is essentially safe for any
ITER_BVEC, but some use cases end up reusing pages and uncondtionally
dropping a page reference on completion. And example of that is
sendfile(2), that ends up being a splice_in + splice_out on the
pipe pages.

Add a flag that tells us it's fine to not grab a page reference
to the bvec pages, since that caller knows not to drop a reference
when it's done with the pages.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_uring: mark me as the maintainer

And io_uring as maintained in general.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_uring: retry bulk slab allocs as single allocs

I've seen cases where bulk alloc fails, since the bulk alloc API
is all-or-nothing - either we get the number we ask for, or it
returns 0 as number of entries.

If we fail a batch bulk alloc, retry a "normal" kmem_cache_alloc()
and just use that instead of failing with -EAGAIN.

While in there, ensure we use GFP_KERNEL. That was an oversight in
the original code, when we switched away from GFP_ATOMIC.

Signed-off-by: Jens Axboe <axboe@kernel.dk>

selinux: fix NULL dereference in policydb_destroy()

The conversion to kvmalloc() forgot to account for the possibility that
p->type_attr_map_array might be null in policydb_destroy().

Fix this by destroying its contents only if it is not NULL.

Also make sure ebitmap_init() is called on all entries before
policydb_destroy() can be called. Right now this is a no-op, because
both kvcalloc() and ebitmap_init() just zero out the whole struct, but
let's rather not rely on a specific implementation.

Reported-by: syzbot+a57b2aff60832666fc28@syzkaller.appspotmail.com
Fixes: acdf52d97f82 ("selinux: convert to kvmalloc")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>

udf: Propagate errors from udf_truncate_extents()

Make udf_truncate_extents() properly propagate errors to its callers and
let udf_setsize() handle the error properly as well. This lets userspace
know in case there's some error when truncating blocks.

Signed-off-by: Jan Kara <jack@suse.cz>