thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()
Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.
Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.
Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:
3.3.6.4. Gating and reset
Make sure that the reset signal has been released before the release of
module clock gating;
This fixes the issue and removes some LoC at the same time.
That change was causing a regression in the generic-adc-thermal-probed
bootrr test as reported in the kernelci-results list [1].
A proper rework will take longer, so revert it for now.
Stephan Gerhold [Wed, 7 Jun 2023 10:47:49 +0000 (12:47 +0200)]
thermal/drivers/qcom/tsens-v0_1: Add MSM8909 data
The MSM8909 SoC has 5 thermal sensors in a TSENS v0.1 block. Like
MDM9607 it uses a non-standard default slope value of 3000 [1] and needs
per-sensor "correction factors" to workaround issues with the factory
calibration [2].
Stephan Gerhold [Wed, 7 Jun 2023 10:47:47 +0000 (12:47 +0200)]
dt-bindings: thermal: qcom-tsens: Drop redundant compatibles
Since the SoC compatibles must be followed by the IP version compatible
(e.g. compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";) it is
redundant to list all the SoC compatibles again in the if statement.
It will already match the IP-version compatible.
The list has already become inconsistent since for example
"qcom,msm8939-tsens" is covered by the if statement but is not listed
there explicitly like the other SoCs.
Simplify this by dropping the redundant SoC compatibles. ipq8064 and
msm8960 are still needed because they do not have an IP-version
compatible.
According to the msm-3.18 vendor kernel from Qualcomm, mdm9607 needs
"correction factors" to adjust for additional offsets observed after the
factory calibration values in the fuses [1, 2].
The fixed offsets should be applied unless there is a special
calibration mode value that indicates that no offsets are needed [3].
Note that the new calibration mode values are called differently in this
patch compared to the vendor kernel:
- TSENS_TWO_POINT_CALIB_N_WA -> ONE_PT_CALIB2_NO_OFFSET
- TSENS_TWO_POINT_CALIB_N_OFFSET_WA -> TWO_PT_CALIB_NO_OFFSET
This is because close inspection of the calibration function [3] reveals
that TSENS_TWO_POINT_CALIB_N_WA is actually a "one point" calibration
because the if statements skip all "point2" related code for it.
According to the msm-3.18 vendor kernel from Qualcomm [1], mdm9607 uses
a non-standard slope value of 3000 (instead of 3200) for all sensors.
Fill it properly similar to the 8939 code added recently.
Stephan Gerhold [Wed, 7 Jun 2023 10:47:44 +0000 (12:47 +0200)]
thermal/drivers/qcom/tsens: Drop unused legacy structs
The old single-cell parsing code was removed for MSM8939, MDM9607 and
MSM8976 but for some reason the structs defining the bit positions etc
were kept around (unused). Drop them now.
Cc: Dmitry Baryshkov <[email protected]> Fixes: 51d78b8b1beb ("thermal/drivers/tsens: Drop single-cell code for mdm9607") Fixes: dfadb4599ab0 ("thermal/drivers/tsens: Drop single-cell code for msm8939") Fixes: 3a908971f7cb ("thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956") Reviewed-by: Konrad Dybcio <[email protected]> Signed-off-by: Stephan Gerhold <[email protected]> Reviewed-by: Dmitry Baryshkov <[email protected]> Signed-off-by: Daniel Lezcano <[email protected]> Link: https://lore.kernel.org/r/[email protected]
Thierry Reding [Fri, 9 Jun 2023 12:44:08 +0000 (14:44 +0200)]
thermal: Allow selecting the bang-bang governor as default
For many setups the bang-bang governor is exactly what we want. Many
ARM SoC-based devices use fans to cool down the entire SoC and that
works well only with the bang-bang governor because it uses the
hysteresis in order to let the fan run for a while to cool the SoC
down below the trip point before switching it off again.
The step-wise governor will behave strangely in these situations. It
doesn't use the hysteresis, so it can lead to situations where the fan
is turned on for only a very brief period and then is switched back off,
only to get switched back on again very quickly because the SoC hasn't
cooled down very much.
Thomas Gleixner [Mon, 26 Jun 2023 09:05:49 +0000 (11:05 +0200)]
Merge tag 'irqchip-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A number of Loogson/Loogarch fixes
- Allow the core code to retrigger an interrupt that has
fired while the same interrupt is being handled on another
CPU, papering over a GICv3 architecture issue
- Work around an integration problem on ASR8601, where the CPU
numbering isn't representable in the GIC implementation...
- Add some missing interrupt to the STM32 irqchip
- A bunch of warning squashing triggered by W=1 builds
Thomas Gleixner [Mon, 26 Jun 2023 09:04:01 +0000 (11:04 +0200)]
Merge tag 'timers-v6.5-rc1' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clockevent/source updates from Daniel Lezcano:
- Fix memory leak on Cadence TTC at probe time (Feng Mingxi)
- Use the pm_sleep_ptr macro for the Ingenic driver (Paul Cercueil)
- Relocate the PMW timer Loongson from the mips arch directory to the
drivers/clocksource (Keguang Zhang)
- Use the same function names instead of using aliases and move data
defined in the header to the driver directly as this one is the only
user of the header file and remove this one on i.MX GPT (Uwe
Kleine-König)
- Convert Broadcom Kona family timer bindings to DT schema (Michael
Kelley)
- Add DT bindings for Ralink SoCs timer (Sergio Paracuellos)
Linus Torvalds [Sun, 25 Jun 2023 22:36:01 +0000 (15:36 -0700)]
Merge tag 'i2c-for-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Nothing fancy. Two driver and one DT binding fix"
* tag 'i2c-for-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx-lpi2c: fix type char overflow issue when calculating the clock cycle
i2c: qup: Add missing unwind goto in qup_i2c_probe()
dt-bindings: i2c: opencores: Add missing type for "regstep"
Linus Torvalds [Sun, 25 Jun 2023 17:13:17 +0000 (10:13 -0700)]
Merge tag 'perf_urgent_for_v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Drop the __weak attribute from a function prototype as it otherwise
leads to the function getting replaced by a dummy stub
- Fix the umask value setup of the frontend event as former is
different on two Intel cores
* tag 'perf_urgent_for_v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Fix the FRONTEND encoding on GNR and MTL
perf/core: Drop __weak attribute from arch_perf_update_userpage() prototype
Linus Torvalds [Sun, 25 Jun 2023 16:47:04 +0000 (09:47 -0700)]
Merge tag 'x86_urgent_for_v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Do not use set_pgd() when updating the KASLR trampoline pgd entry
because that updates the user PGD too on KPTI builds, resulting in
memory corruption
- Prevent a panic in the IO-APIC setup code due to conflicting command
line parameters
* tag 'x86_urgent_for_v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Fix kernel panic when booting with intremap=off and x2apic_phys
x86/mm: Avoid using set_pgd() outside of real PGD pages
Linus Torvalds [Fri, 23 Jun 2023 23:33:26 +0000 (16:33 -0700)]
Merge tag 'drm-fixes-2023-06-23' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Very quiet last week, just two misc fixes, one dp-mst and one qaic:
qaic:
- dma-buf import fix
dp-mst:
- fix NULL ptr deref"
[ It turns out it was a quiet week because Alex Deucher hadn't sent in
his pending AMD changes. So they are coming next - Linus ]
* tag 'drm-fixes-2023-06-23' of git://anongit.freedesktop.org/drm/drm:
drm: use mgr->dev in drm_dbg_kms in drm_dp_add_payload_part2
accel/qaic: Call DRM helper function to destroy prime GEM
Linus Torvalds [Fri, 23 Jun 2023 23:21:59 +0000 (16:21 -0700)]
Merge tag 'arm-fixes-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"The final bug fixes for Qualcomm and Rockchips came in, all of them
for devicetree files:
- Devices on Qualcomm SC7180/SC7280 that are cache coherent are now
marked so correctly to fix a regression after a change in kernel
behavior
- Rockchips has a few minor changes for correctness of regulator and
cache properties, as well as fixes for incorrect behavior of the
RK3568 PCI controller and reset pins on two boards"
* tag 'arm-fixes-6.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: qcom: sc7280: Mark SCM as dma-coherent for chrome devices
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for trogdor
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for IDP
dt-bindings: firmware: qcom,scm: Document that SCM can be dma-coherent
arm64: dts: rockchip: Fix rk356x PCIe register and range mappings
arm64: dts: rockchip: fix button reset pin for nanopi r5c
arm64: dts: rockchip: fix nEXTRST on SOQuartz
arm64: dts: rockchip: add missing cache properties
arm64: dts: rockchip: fix USB regulator on ROCK64
Linus Torvalds [Fri, 23 Jun 2023 23:09:53 +0000 (16:09 -0700)]
Merge tag 'for-6.4-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"Unfortunately the recent u32 overflow fix was not complete, there was
one conversion left, assertion not triggered by my tests but caught by
Qu's fstests case.
The "cleanup for later" has been promoted to a proper fix and wraps
all uses of the stripe left shift so the diffstat has grown but leaves
no potentially problematic uses.
We should have done it that way before, sorry"
* tag 'for-6.4-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix remaining u32 overflows when left shifting stripe_nr
Linus Torvalds [Fri, 23 Jun 2023 22:43:01 +0000 (15:43 -0700)]
Merge tag 'sound-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Three oneliner fixes: one for a thinko in SOF SoundWire code and two
HD-audio quirks for ASUS laptops. All device-specific and should be
safe to apply"
* tag 'sound-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirk for ASUS ROG GV601V
ALSA: hda/realtek: Add quirk for ASUS ROG G634Z
ASoC: intel: sof_sdw: Fixup typo in device link checking
Arnd Bergmann [Fri, 23 Jun 2023 20:13:22 +0000 (22:13 +0200)]
Merge tag 'qcom-arm64-fixes-for-6.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
One last Qualcomm ARM64 DeviceTree fix for v6.4
Changes related to cache management for DMA memory caused WiFi to stop
work on SC7180 and SC7280 based products, using TF-A. These changes
marks the relevant device dma-coherent to correct the behavior.
* tag 'qcom-arm64-fixes-for-6.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sc7280: Mark SCM as dma-coherent for chrome devices
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for trogdor
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for IDP
dt-bindings: firmware: qcom,scm: Document that SCM can be dma-coherent
Linus Torvalds [Fri, 23 Jun 2023 19:08:14 +0000 (12:08 -0700)]
workqueue: clean up WORK_* constant types, clarify masking
Dave Airlie reports that gcc-13.1.1 has started complaining about some
of the workqueue code in 32-bit arm builds:
kernel/workqueue.c: In function ‘get_work_pwq’:
kernel/workqueue.c:713:24: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
713 | return (void *)(data & WORK_STRUCT_WQ_DATA_MASK);
| ^
[ ... a couple of other cases ... ]
and while it's not immediately clear exactly why gcc started complaining
about it now, I suspect it's some C23-induced enum type handlign fixup in
gcc-13 is the cause.
Whatever the reason for starting to complain, the code and data types
are indeed disgusting enough that the complaint is warranted.
The wq code ends up creating various "helper constants" (like that
WORK_STRUCT_WQ_DATA_MASK) using an enum type, which is all kinds of
confused. The mask needs to be 'unsigned long', not some unspecified
enum type.
To make matters worse, the actual "mask and cast to a pointer" is
repeated a couple of times, and the cast isn't even always done to the
right pointer, but - as the error case above - to a 'void *' with then
the compiler finishing the job.
That's now how we roll in the kernel.
So create the masks using the proper types rather than some ambiguous
enumeration, and use a nice helper that actually does the type
conversion in one well-defined place.
Incidentally, this magically makes clang generate better code. That,
admittedly, is really just a sign of clang having been seriously
confused before, and cleaning up the typing unconfuses the compiler too.
* arm64/for-next/perf:
docs: perf: Fix warning from 'make htmldocs' in hisi-pmu.rst
docs: perf: Add new description for HiSilicon UC PMU
drivers/perf: hisi: Add support for HiSilicon UC PMU driver
drivers/perf: hisi: Add support for HiSilicon H60PA and PAv3 PMU driver
perf: arm_cspmu: Add missing MODULE_DEVICE_TABLE
perf/arm-cmn: Add sysfs identifier
perf/arm-cmn: Revamp model detection
perf/arm_dmc620: Add cpumask
dt-bindings: perf: fsl-imx-ddr: Add i.MX93 compatible
drivers/perf: imx_ddr: Add support for NXP i.MX9 SoC DDRC PMU driver
perf/arm_cspmu: Decouple APMT dependency
perf/arm_cspmu: Clean up ACPI dependency
ACPI/APMT: Don't register invalid resource
perf/arm_cspmu: Fix event attribute type
perf: arm_cspmu: Set irq affinitiy only if overflow interrupt is used
drivers/perf: hisi: Don't migrate perf to the CPU going to teardown
drivers/perf: apple_m1: Force 63bit counters for M2 CPUs
perf/arm-cmn: Fix DTC reset
perf: qcom_l2_pmu: Make l2_cache_pmu_probe_cluster() more robust
perf/arm-cci: Slightly optimize cci_pmu_sync_counters()
* for-next/kpti:
: Simplify KPTI trampoline exit code
arm64: entry: Simplify tramp_alias macro and tramp_exit routine
arm64: entry: Preserve/restore X29 even for compat tasks
* for-next/missing-proto-warn:
: Address -Wmissing-prototype warnings
arm64: add alt_cb_patch_nops prototype
arm64: move early_brk64 prototype to header
arm64: signal: include asm/exception.h
arm64: kaslr: add kaslr_early_init() declaration
arm64: flush: include linux/libnvdimm.h
arm64: module-plts: inline linux/moduleloader.h
arm64: hide unused is_valid_bugaddr()
arm64: efi: add efi_handle_corrupted_x18 prototype
arm64: cpuidle: fix #ifdef for acpi functions
arm64: kvm: add prototypes for functions called in asm
arm64: spectre: provide prototypes for internal functions
arm64: move cpu_suspend_set_dbg_restorer() prototype to header
arm64: avoid prototype warnings for syscalls
arm64: add scs_patch_vmlinux prototype
arm64: xor-neon: mark xor_arm64_neon_*() static
* for-next/iss2-decode:
: Add decode of ISS2 to data abort reports
arm64/esr: Add decode of ISS2 to data abort reporting
arm64/esr: Use GENMASK() for the ISS mask
* for-next/kselftest:
: Various arm64 kselftest improvements
kselftest/arm64: Log signal code and address for unexpected signals
kselftest/arm64: Add a smoke test for ptracing hardware break/watch points
* for-next/misc:
: Miscellaneous patches
arm64: alternatives: make clean_dcache_range_nopatch() noinstr-safe
arm64: hibernate: remove WARN_ON in save_processor_state
arm64/fpsimd: Exit streaming mode when flushing tasks
arm64: mm: fix VA-range sanity check
arm64/mm: remove now-superfluous ISBs from TTBR writes
arm64: consolidate rox page protection logic
arm64: set __exception_irq_entry with __irq_entry as a default
arm64: syscall: unmask DAIF for tracing status
arm64: lockdep: enable checks for held locks when returning to userspace
arm64/cpucaps: increase string width to properly format cpucaps.h
arm64/cpufeature: Use helper for ECV CNTPOFF cpufeature
* for-next/feat_mops:
: Support for ARMv8.8 memcpy instructions in userspace
kselftest/arm64: add MOPS to hwcap test
arm64: mops: allow disabling MOPS from the kernel command line
arm64: mops: detect and enable FEAT_MOPS
arm64: mops: handle single stepping after MOPS exception
arm64: mops: handle MOPS exceptions
KVM: arm64: hide MOPS from guests
arm64: mops: don't disable host MOPS instructions from EL2
arm64: mops: document boot requirements for MOPS
KVM: arm64: switch HCRX_EL2 between host and guest
arm64: cpufeature: detect FEAT_HCX
KVM: arm64: initialize HCRX_EL2
* for-next/module-alloc:
: Make the arm64 module allocation code more robust (clean-up, VA range expansion)
arm64: module: rework module VA range selection
arm64: module: mandate MODULE_PLTS
arm64: module: move module randomization to module.c
arm64: kaslr: split kaslr/module initialization
arm64: kasan: remove !KASAN_VMALLOC remnants
arm64: module: remove old !KASAN_VMALLOC logic
* for-next/sysreg: (21 commits)
: More sysreg conversions to automatic generation
arm64/sysreg: Convert TRBIDR_EL1 register to automatic generation
arm64/sysreg: Convert TRBTRG_EL1 register to automatic generation
arm64/sysreg: Convert TRBMAR_EL1 register to automatic generation
arm64/sysreg: Convert TRBSR_EL1 register to automatic generation
arm64/sysreg: Convert TRBBASER_EL1 register to automatic generation
arm64/sysreg: Convert TRBPTR_EL1 register to automatic generation
arm64/sysreg: Convert TRBLIMITR_EL1 register to automatic generation
arm64/sysreg: Rename TRBIDR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBTRG_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBMAR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBSR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBBASER_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBPTR_EL1 fields per auto-gen tools format
arm64/sysreg: Rename TRBLIMITR_EL1 fields per auto-gen tools format
arm64/sysreg: Convert OSECCR_EL1 to automatic generation
arm64/sysreg: Convert OSDTRTX_EL1 to automatic generation
arm64/sysreg: Convert OSDTRRX_EL1 to automatic generation
arm64/sysreg: Convert OSLAR_EL1 to automatic generation
arm64/sysreg: Standardise naming of bitfield constants in OSL[AS]R_EL1
arm64/sysreg: Convert MDSCR_EL1 to automatic register generation
...
* for-next/cpucap:
: arm64 cpucap clean-up
arm64: cpufeature: fold cpus_set_cap() into update_cpu_capabilities()
arm64: cpufeature: use cpucap naming
arm64: alternatives: use cpucap naming
arm64: standardise cpucap bitmap names
* for-next/acpi:
: Various arm64-related ACPI patches
ACPI: bus: Consolidate all arm specific initialisation into acpi_arm_init()
* for-next/kdump:
: Simplify the crashkernel reservation behaviour of crashkernel=X,high on arm64
arm64: add kdump.rst into index.rst
Documentation: add kdump.rst to present crashkernel reservation on arm64
arm64: kdump: simplify the reservation behaviour of crashkernel=,high
* for-next/acpi-doc:
: Update ACPI documentation for Arm systems
Documentation/arm64: Update ACPI tables from BBR
Documentation/arm64: Update references in arm-acpi
Documentation/arm64: Update ARM and arch reference
* for-next/tpidr2-fix:
: Fix the TPIDR2_EL0 register restoring on sigreturn
kselftest/arm64: Add a test case for TPIDR2 restore
arm64/signal: Restore TPIDR2 register rather than memory state
Mark Brown [Thu, 22 Jun 2023 13:39:46 +0000 (14:39 +0100)]
kselftest/arm64: Add a test case for TPIDR2 restore
Due to the fact that TPIDR2 is intended to be managed by libc we don't
currently test modifying it via the signal context since that might
disrupt libc's usage of it and cause instability. We can however test the
opposite case with less risk, modifying TPIDR2 in a signal handler and
making sure that the original value is restored after returning from the
signal handler. Add a test which does this.
Mark Brown [Thu, 22 Jun 2023 13:39:45 +0000 (14:39 +0100)]
arm64/signal: Restore TPIDR2 register rather than memory state
Currently when restoring the TPIDR2 signal context we set the new value
from the signal frame in the thread data structure but not the register,
following the pattern for the rest of the data we are restoring. This does
not work in the case of TPIDR2, the register always has the value for the
current task. This means that either we return to userspace and ignore the
new value or we context switch and save the register value on top of the
newly restored value.
Load the value from the signal context into the register instead.
Yu Kuai [Wed, 21 Jun 2023 16:01:11 +0000 (00:01 +0800)]
scsi/sg: don't grab scsi host module reference
In order to prevent request_queue to be freed before cleaning up
blktrace debugfs entries, commit db59133e9279 ("scsi: sg: fix blktrace
debugfs entries leakage") use scsi_device_get(), however,
scsi_device_get() will also grab scsi module reference and scsi module
can't be removed.
It's reported that blktests can't unload scsi_debug after block/001:
Fix this problem by grabbing request_queue reference directly, so that
scsi host module can still be unloaded while request_queue will be
pinged by sg device.
Pavel Begunkov [Fri, 23 Jun 2023 11:23:31 +0000 (12:23 +0100)]
io_uring: merge conditional unlock flush helpers
There is no reason not to use __io_cq_unlock_post_flush for intermediate
aux CQE flushing, all ->task_complete should apply there, i.e. if set it
should be the submitter task. Combine them, get rid of of
__io_cq_unlock_post() and rename the left function.
This place was also taking a couple percents of CPU according to
profiles for max throughput net benchmarks due to multishot recv
flooding it with completions.
Pavel Begunkov [Fri, 23 Jun 2023 11:23:27 +0000 (12:23 +0100)]
io_uring: kill io_cq_unlock()
We're abusing ->completion_lock helpers. io_cq_unlock() neither
locking conditionally nor doing CQE flushing, which means that callers
must have some side reason of taking the lock and should do it directly.
Open code io_cq_unlock() into io_cqring_overflow_kill() and clean it up.
Pavel Begunkov [Fri, 23 Jun 2023 11:23:26 +0000 (12:23 +0100)]
io_uring: remove IOU_F_TWQ_FORCE_NORMAL
Extract a function for non-local task_work_add, and use it directly from
io_move_task_work_from_local(). Now we don't use IOU_F_TWQ_FORCE_NORMAL
and it can be killed.
As a small positive side effect we don't grab task->io_uring in
io_req_normal_work_add anymore, which is not needed for
io_req_local_work_add().
Pavel Begunkov [Fri, 23 Jun 2023 11:23:25 +0000 (12:23 +0100)]
io_uring: don't batch task put on reqs free
We're trying to batch io_put_task() in io_free_batch_list(), but
considering that the hot path is a simple inc, it's most cerainly and
probably faster to just do io_put_task() instead of task tracking.
We don't care about io_put_task_remote() as it's only for IOPOLL
where polling/waiting is done by not the submitter task.
Pavel Begunkov [Fri, 23 Jun 2023 11:23:22 +0000 (12:23 +0100)]
io_uring: remove io_free_req_tw
Request completion is a very hot path in general, but there are 3 places
that can be doing it: io_free_batch_list(), io_req_complete_post() and
io_free_req_tw().
io_free_req_tw() is used rather marginally and we don't care about it.
Killing it can help to clean up and optimise the left two, do that by
replacing it with io_req_task_complete().
There are two things to consider:
1) io_free_req() is called when all refs are put, so we need to reinit
references. The easiest way to do that is to clear REQ_F_REFCOUNT.
2) We also don't need a cqe from it, so silence it with REQ_F_CQE_SKIP.
The goto label "fail_runtime" and "fail" will disable qup->pclk,
but here qup->pclk failed to obtain, in order to be consistent,
change the direct return to goto label "fail_dma".
clocksource/drivers/cadence-ttc: Fix memory leak in ttc_timer_probe
Smatch reports:
drivers/clocksource/timer-cadence-ttc.c:529 ttc_timer_probe()
warn: 'timer_baseaddr' from of_iomap() not released on lines: 498,508,516.
timer_baseaddr may have the problem of not being released after use,
I replaced it with the devm_of_iomap() function and added the clk_put()
function to cleanup the "clk_ce" and "clk_cs".
Michael Kelley [Mon, 19 Jun 2023 19:02:40 +0000 (12:02 -0700)]
clocksource/drivers/hyper-v: Rework clocksource and sched clock setup
Current code assigns either the Hyper-V TSC page or MSR-based ref counter
as the sched clock. This may be sub-optimal in two cases. First, if there
is hardware support to ensure consistent TSC frequency across live
migrations and Hyper-V is using that support, the raw TSC is a faster
source of time than the Hyper-V TSC page. Second, the MSR-based ref
counter is relatively slow because reads require a trap to the hypervisor.
As such, it should never be used as the sched clock. The native sched
clock based on the raw TSC or jiffies is much better.
Rework the sched clock setup so it is set to the TSC page only if
Hyper-V indicates that the TSC may have inconsistent frequency across
live migrations. Also, remove the code that sets the sched clock to
the MSR-based ref counter. In the cases where it is not set, the sched
clock will then be the native sched clock.
As part of the rework, always enable both the TSC page clocksource and
the MSR-based ref counter clocksource. Set the ratings so the TSC page
clocksource is preferred. While the MSR-based ref counter clocksource
is unlikely to ever be the default, having it available for manual
selection is convenient for development purposes.
Linus Torvalds [Fri, 23 Jun 2023 00:59:51 +0000 (17:59 -0700)]
Merge tag 'net-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ipsec, bpf, mptcp and netfilter.
Current release - regressions:
- netfilter: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain
- eth: mlx5e:
- fix scheduling of IPsec ASO query while in atomic
- free IRQ rmap and notifier on kernel shutdown
Current release - new code bugs:
- phy: manual remove LEDs to ensure correct ordering
Previous releases - regressions:
- mptcp: fix possible divide by zero in recvmsg()
- dsa: revert "net: phy: dp83867: perform soft reset and retain
established link"
Previous releases - always broken:
- sched: netem: acquire qdisc lock in netem_change()
- bpf:
- fix verifier id tracking of scalars on spill
- fix NULL dereference on exceptions
- accept function names that contain dots
- netfilter: disallow element updates of bound anonymous sets
- mptcp: ensure listener is unhashed before updating the sk status
- xfrm:
- add missed call to delete offloaded policies
- fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
- selftests: fixes for FIPS mode
- dsa: mt7530: fix multiple CPU ports, BPDU and LLDP handling
- eth: sfc: use budget for TX completions
Misc:
- wifi: iwlwifi: add support for SO-F device with PCI id 0x7AF0"
* tag 'net-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
revert "net: align SO_RCVMARK required privileges with SO_MARK"
net: wwan: iosm: Convert single instance struct member to flexible array
sch_netem: acquire qdisc lock in netem_change()
selftests: forwarding: Fix race condition in mirror installation
wifi: mac80211: report all unusable beacon frames
mptcp: ensure listener is unhashed before updating the sk status
mptcp: drop legacy code around RX EOF
mptcp: consolidate fallback and non fallback state machine
mptcp: fix possible list corruption on passive MPJ
mptcp: fix possible divide by zero in recvmsg()
mptcp: handle correctly disconnect() failures
bpf: Force kprobe multi expected_attach_type for kprobe_multi link
bpf/btf: Accept function names that contain dots
Revert "net: phy: dp83867: perform soft reset and retain established link"
net: mdio: fix the wrong parameters
netfilter: nf_tables: Fix for deleting base chains with payload
netfilter: nfnetlink_osf: fix module autoload
netfilter: nf_tables: drop module reference after updating chain
netfilter: nf_tables: disallow timeout for anonymous sets
netfilter: nf_tables: disallow updates of anonymous sets
...
Linus Torvalds [Fri, 23 Jun 2023 00:38:11 +0000 (17:38 -0700)]
Merge tag 'platform-drivers-x86-v6.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fix from Hans de Goede:
"One small fix for an AMD PMF driver issue which is causing issues for
users of just released AMD laptop models"
* tag 'platform-drivers-x86-v6.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/amd/pmf: Register notify handler only if SPS is enabled
Linus Torvalds [Fri, 23 Jun 2023 00:32:34 +0000 (17:32 -0700)]
Merge tag 'io_uring-6.4-2023-06-21' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
"A fix for a race condition with poll removal and linked timeouts, and
then a few followup fixes/tweaks for the msg_control patch from last
week.
Not super important, particularly the sparse fixup, as it was broken
before that recent commit. But let's get it sorted for real for this
release, rather than just have it broken a bit differently"
* tag 'io_uring-6.4-2023-06-21' of git://git.kernel.dk/linux:
io_uring/net: use the correct msghdr union member in io_sendmsg_copy_hdr
io_uring/net: disable partial retries for recvmsg with cmsg
io_uring/net: clear msg_controllen on partial sendmsg retry
io_uring/poll: serialize poll linked timer start with poll removal
Linus Torvalds [Fri, 23 Jun 2023 00:27:16 +0000 (17:27 -0700)]
Merge tag 'cgroup-for-6.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"It's late but here are two bug fixes. Both fix problems which can be
severe but are very confined in scope. The risk to most use cases
should be minimal.
- Fix for an old bug which triggers if a cgroup subsystem is
remounted to a different hierarchy while someone is reading its
cgroup.procs/tasks file. The risk is pretty low given how seldom
cgroup subsystems are moved across hierarchies.
- We moved cpus_read_lock() outside of cgroup internal locks a while
ago but forgot to update the legacy_freezer leading to lockdep
triggers. Fixed"
* tag 'cgroup-for-6.4-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Do not corrupt task iteration when rebinding subsystem
cgroup,freezer: hold cpu_hotplug_lock before freezer_mutex in freezer_css_{online,offline}()
Douglas Anderson [Fri, 16 Jun 2023 15:14:41 +0000 (08:14 -0700)]
arm64: dts: qcom: sc7280: Mark SCM as dma-coherent for chrome devices
Just like for sc7180 devices using the Chrome bootflow (AKA trogdor
and IDP), sc7280 devices using the Chrome bootflow also need their
firmware marked dma-coherent. On sc7280 this wasn't causing WiFi to
fail to startup, since WiFi works differently there. However, on
sc7280 devices we were still getting the message at bootup after
commit 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""):
Douglas Anderson [Fri, 16 Jun 2023 15:14:40 +0000 (08:14 -0700)]
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for trogdor
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable.
Specifically, you can see in Trogdor's TF-A code [1] in
qti_sip_mem_assign() that we call qti_mmap_add_dynamic_region() with
MT_RO_DATA. This translates down to MT_MEMORY instead of
MT_NON_CACHEABLE or MT_DEVICE. Apparently Qualcomm's normal TZ
implementation maps the memory as non-cacheable.
Let's add the "dma-coherent" attribute to the SCM for trogdor.
Adding "dma-coherent" like this fixes WiFi on sc7180-trogdor
devices. WiFi was broken as of commit 7bd6680b47fa ("Revert "Revert
"arm64: dma: Drop cache invalidation from
arch_dma_prep_coherent()"""). Specifically at bootup we'd get:
From discussion on the mailing lists [2] and over IRC [3], it was
determined that we should always have been tagging the SCM as
dma-coherent on trogdor but that the old "invalidate" happened to make
things work most of the time. Tagging it properly like this is a much
more robust solution.
Douglas Anderson [Fri, 16 Jun 2023 15:14:39 +0000 (08:14 -0700)]
arm64: dts: qcom: sc7180: Mark SCM as dma-coherent for IDP
sc7180-idp is, for most intents and purposes, a trogdor device.
Specifically, sc7180-idp is designed to run the same style of firmware
as trogdor devices. This can be seen from the fact that IDP has the
same "Reserved memory changes" in its device tree that trogdor has.
Recently it was realized that we need to mark SCM as dma-coherent to
match what trogdor's style of firmware (based on TF-A) does [1]. That
means we need this dma-coherent tag on IDP as well.
Without this, on newer versions of Linux, specifically those with
commit 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""), WiFi will fail to
work. At bootup you'll see:
Douglas Anderson [Fri, 16 Jun 2023 15:14:38 +0000 (08:14 -0700)]
dt-bindings: firmware: qcom,scm: Document that SCM can be dma-coherent
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable. Specifically,
you can see in Trogdor's TF-A code [1] in qti_sip_mem_assign() that we
call qti_mmap_add_dynamic_region() with MT_RO_DATA. This translates
down to MT_MEMORY instead of MT_NON_CACHEABLE or MT_DEVICE.
Let's allow devices like trogdor to be described properly by allowing
"dma-coherent" in the SCM node.
Gavin Shan [Thu, 15 Jun 2023 05:42:59 +0000 (15:42 +1000)]
KVM: Avoid illegal stage2 mapping on invalid memory slot
We run into guest hang in edk2 firmware when KSM is kept as running on
the host. The edk2 firmware is waiting for status 0x80 from QEMU's pflash
device (TYPE_PFLASH_CFI01) during the operation of sector erasing or
buffered write. The status is returned by reading the memory region of
the pflash device and the read request should have been forwarded to QEMU
and emulated by it. Unfortunately, the read request is covered by an
illegal stage2 mapping when the guest hang issue occurs. The read request
is completed with QEMU bypassed and wrong status is fetched. The edk2
firmware runs into an infinite loop with the wrong status.
The illegal stage2 mapping is populated due to same page sharing by KSM
at (C) even the associated memory slot has been marked as invalid at (B)
when the memory slot is requested to be deleted. It's notable that the
active and inactive memory slots can't be swapped when we're in the middle
of kvm_mmu_notifier_change_pte() because kvm->mn_active_invalidate_count
is elevated, and kvm_swap_active_memslots() will busy loop until it reaches
to zero again. Besides, the swapping from the active to the inactive memory
slots is also avoided by holding &kvm->srcu in __kvm_handle_hva_range(),
corresponding to synchronize_srcu_expedited() in kvm_swap_active_memslots().
Fix the issue by skipping the invalid memory slot at (C) to avoid the
illegal stage2 mapping so that the read request for the pflash's status
is forwarded to QEMU and emulated by it. In this way, the correct pflash's
status can be returned from QEMU to break the infinite loop in the edk2
firmware.
We tried a git-bisect and the first problematic commit is cd4c71835228 ("
KVM: arm64: Convert to the gfn-based MMU notifier callbacks"). With this,
clean_dcache_guest_page() is called after the memory slots are iterated
in kvm_mmu_notifier_change_pte(). clean_dcache_guest_page() is called
before the iteration on the memory slots before this commit. This change
literally enlarges the racy window between kvm_mmu_notifier_change_pte()
and memory slot removal so that we're able to reproduce the issue in a
practical test case. However, the issue exists since commit d5d8184d35c9
("KVM: ARM: Memory virtualization setup").
block: don't return -EINVAL for not found names in devt_from_devname
When we didn't find a device and didn't guess it might be a partition,
it might still show up later, so don't disable rootwait for it by
returning -EINVAL.
Qu Wenruo [Thu, 22 Jun 2023 06:42:40 +0000 (14:42 +0800)]
btrfs: fix remaining u32 overflows when left shifting stripe_nr
There was regression caused by a97699d1d610 ("btrfs: replace
map_lookup->stripe_len by BTRFS_STRIPE_LEN") and supposedly fixed by a7299a18a179 ("btrfs: fix u32 overflows when left shifting stripe_nr").
To avoid code churn the fix was open coding the type casts but
unfortunately missed one which was still possible to hit [1].
The missing place was assignment of bioc->full_stripe_logical inside
btrfs_map_block().
Fix it by adding a helper that does the safe calculation of the offset
and use it everywhere even though it may not be strictly necessary due
to already using u64 types. This replaces all remaining
"<< BTRFS_STRIPE_LEN_SHIFT" calls.
Ming Lei [Thu, 22 Jun 2023 08:42:49 +0000 (16:42 +0800)]
block: make sure local irq is disabled when calling __blkcg_rstat_flush
When __blkcg_rstat_flush() is called from cgroup_rstat_flush*() code
path, interrupt is always disabled.
When we start to flush blkcg per-cpu stats list in __blkg_release()
for avoiding to leak blkcg_gq's reference in commit 20cb1c2fb756
("blk-cgroup: Flush stats before releasing blkcg_gq"), local irq
isn't disabled yet, then lockdep warning may be triggered because
the dependent cgroup locks may be acquired from irq(soft irq) handler.
Sandeep Dhavale [Wed, 21 Jun 2023 22:08:47 +0000 (15:08 -0700)]
erofs: Fix detection of atomic context
Current check for atomic context is not sufficient as
z_erofs_decompressqueue_endio can be called under rcu lock
from blk_mq_flush_plug_list(). See the stacktrace [1]
In such case we should hand off the decompression work for async
processing rather than trying to do sync decompression in current
context. Patch fixes the detection by checking for
rcu_read_lock_any_held() and while at it use more appropriate
!in_task() check than in_atomic().
Background: Historically erofs would always schedule a kworker for
decompression which would incur the scheduling cost regardless of
the context. But z_erofs_decompressqueue_endio() may not always
be in atomic context and we could actually benefit from doing the
decompression in z_erofs_decompressqueue_endio() if we are in
thread context, for example when running with dm-verity.
This optimization was later added in patch [2] which has shown
improvement in performance benchmarks.
Niklas Schnelle [Fri, 2 Jun 2023 14:09:27 +0000 (16:09 +0200)]
s390/defconfigs: set CONFIG_NET_TC_SKB_EXT=y
As made explicit by commit 03a283cdc8c8 ("net/mlx5: Kconfig: Make tc
offload depend on tc skb extension") tc skb extension is required for
offloading tc as well as bridges on switchdev capable ConnectX devices.
Paolo Abeni [Thu, 22 Jun 2023 12:39:06 +0000 (14:39 +0200)]
Merge tag 'nf-23-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
This is v3, including a crash fix for patch 01/14.
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix UDP segmentation with IPVS tunneled traffic, from Terin Stock.
2) Fix chain binding transaction logic, add a bound flag to rule
transactions. Remove incorrect logic in nft_data_hold() and
nft_data_release().
3) Add a NFT_TRANS_PREPARE_ERROR deactivate state to deal with releasing
the set/chain as a follow up to 1240eb93f061 ("netfilter: nf_tables:
incorrect error path handling with NFT_MSG_NEWRULE")
4) Drop map element references from preparation phase instead of
set destroy path, otherwise bogus EBUSY with transactions such as:
flush chain ip x y
delete chain ip x w
where chain ip x y contains jump/goto from set elements.
5) Pipapo set type does not regard generation mask from the walk
iteration.
6) Fix reference count underflow in set element reference to
stateful object.
7) Several patches to tighten the nf_tables API:
- disallow set element updates of bound anonymous set
- disallow unbound anonymous set/chain at the end of transaction.
- disallow updates of anonymous set.
- disallow timeout configuration for anonymous sets.
8) Fix module reference leak in chain updates.
9) Fix nfnetlink_osf module autoload.
10) Fix deletion of basechain when NFTA_CHAIN_HOOK is specified as
in iptables-nft.
This Netfilter batch is larger than usual at this stage, I am aware we
are fairly late in the -rc cycle, if you prefer to route them through
net-next, please let me know.
netfilter pull request 23-06-21
* tag 'nf-23-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: Fix for deleting base chains with payload
netfilter: nfnetlink_osf: fix module autoload
netfilter: nf_tables: drop module reference after updating chain
netfilter: nf_tables: disallow timeout for anonymous sets
netfilter: nf_tables: disallow updates of anonymous sets
netfilter: nf_tables: reject unbound chain set before commit phase
netfilter: nf_tables: reject unbound anonymous set before commit phase
netfilter: nf_tables: disallow element updates of bound anonymous sets
netfilter: nf_tables: fix underflow in object reference counter
netfilter: nft_set_pipapo: .walk does not deal with generations
netfilter: nf_tables: drop map element references from preparation phase
netfilter: nf_tables: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain
netfilter: nf_tables: fix chain binding transaction logic
ipvs: align inner_mac_header for encapsulation
====================
Thomas Richter [Thu, 15 Jun 2023 11:31:58 +0000 (13:31 +0200)]
s390/cpum_cf: rework PER_CPU_DEFINE of struct cpu_cf_events
Struct cpu_cf_events is a large data structure and is statically defined
for each possible CPU. Rework this and replace it by dynamically
allocated data structures created when a perf_event_open() system call
is invoked or an access via character device /dev/hwctr takes place.
It is replaced by an array of pointers to all possible CPUs and
reference counting. The array of pointers is allocated when the first
event is created. For each online CPU an event is installed on, a struct
cpu_cf_events is allocated and a pointer to struct cpu_cf_events is
stored in the array:
With this approach the large data structure is only allocated when
an event is actually installed and used.
Also implement proper reference counting for allocation and removal.
During interrupt processing make sure the pointer to cpu_cf_events
is valid. The interrupt handler is shared and might be called when
no event is active.
This requires checking for a valid pointer to struct cpu_cf_events.
When the pointer to the per-cpu cpu_cf_events is NULL, simply return.
revert "net: align SO_RCVMARK required privileges with SO_MARK"
This reverts commit 1f86123b9749 ("net: align SO_RCVMARK required
privileges with SO_MARK") because the reasoning in the commit message
is not really correct:
SO_RCVMARK is used for 'reading' incoming skb mark (via cmsg), as such
it is more equivalent to 'getsockopt(SO_MARK)' which has no priv check
and retrieves the socket mark, rather than 'setsockopt(SO_MARK) which
sets the socket mark and does require privs.
Additionally incoming skb->mark may already be visible if
sysctl_fwmark_reflect and/or sysctl_tcp_fwmark_accept are enabled.
Furthermore, it is easier to block the getsockopt via bpf
(either cgroup setsockopt hook, or via syscall filters)
then to unblock it if it requires CAP_NET_RAW/ADMIN.
On Android the socket mark is (among other things) used to store
the network identifier a socket is bound to. Setting it is privileged,
but retrieving it is not. We'd like unprivileged userspace to be able
to read the network id of incoming packets (where mark is set via
iptables [to be moved to bpf])...
An alternative would be to add another sysctl to control whether
setting SO_RCVMARK is privilged or not.
(or even a MASK of which bits in the mark can be exposed)
But this seems like over-engineering...
Note: This is a non-trivial revert, due to later merged commit e42c7beee71d
("bpf: net: Consider has_current_bpf_ctx() when testing capable() in sk_setsockopt()")
which changed both 'ns_capable' into 'sockopt_ns_capable' calls.
Danielle Ratson [Tue, 20 Jun 2023 12:45:15 +0000 (14:45 +0200)]
selftests: forwarding: Fix race condition in mirror installation
When mirroring to a gretap in hardware the device expects to be
programmed with the egress port and all the encapsulating headers. This
requires the driver to resolve the path the packet will take in the
software data path and program the device accordingly.
If the path cannot be resolved (in this case because of an unresolved
neighbor), then mirror installation fails until the path is resolved.
This results in a race that causes the test to sometimes fail.
Fix this by setting the neighbor's state to permanent in a couple of
tests, so that it is always valid.
Benjamin Berg [Wed, 21 Jun 2023 12:05:44 +0000 (14:05 +0200)]
wifi: mac80211: report all unusable beacon frames
Properly check for RX_DROP_UNUSABLE now that the new drop reason
infrastructure is used. Without this change, the comparison will always
be false as a more specific reason is given in the lower bits of result.
Jakub Kicinski [Thu, 22 Jun 2023 05:44:59 +0000 (22:44 -0700)]
Merge branch 'mptcp-fixes-for-6-4'
Matthieu Baerts says:
====================
mptcp: fixes for 6.4
Patch 1 correctly handles disconnect() failures that can happen in some
specific cases: now the socket state is set as unconnected as expected.
That fixes an issue introduced in v6.2.
Patch 2 fixes a divide by zero bug in mptcp_recvmsg() with a fix similar
to a recent one from Eric Dumazet for TCP introducing sk_wait_pending
flag. It should address an issue present in MPTCP from almost the
beginning, from v5.9.
Patch 3 fixes a possible list corruption on passive MPJ even if the race
seems very unlikely, better be safe than sorry. The possible issue is
present from v5.17.
Patch 4 consolidates fallback and non fallback state machines to avoid
leaking some MPTCP sockets. The fix is likely needed for versions from
v5.11.
Patch 5 drops code that is no longer used after the introduction of
patch 4/6. This is not really a fix but this patch can probably land in
the -net tree as well not to leave unused code.
Patch 6 ensures listeners are unhashed before updating their sk status
to avoid possible deadlocks when diag info are going to be retrieved
with a lock. Even if it should not be visible with the way we are
currently getting diag info, the issue is present from v5.17.
====================
Paolo Abeni [Tue, 20 Jun 2023 16:24:23 +0000 (18:24 +0200)]
mptcp: ensure listener is unhashed before updating the sk status
The MPTCP protocol access the listener subflow in a lockless
manner in a couple of places (poll, diag). That works only if
the msk itself leaves the listener status only after that the
subflow itself has been closed/disconnected. Otherwise we risk
deadlock in diag, as reported by Christoph.
Address the issue ensuring that the first subflow (the listener
one) is always disconnected before updating the msk socket status.
Paolo Abeni [Tue, 20 Jun 2023 16:24:22 +0000 (18:24 +0200)]
mptcp: drop legacy code around RX EOF
Thanks to the previous patch -- "mptcp: consolidate fallback and non
fallback state machine" -- we can finally drop the "temporary hack"
used to detect rx eof.
Paolo Abeni [Tue, 20 Jun 2023 16:24:21 +0000 (18:24 +0200)]
mptcp: consolidate fallback and non fallback state machine
An orphaned msk releases the used resources via the worker,
when the latter first see the msk in CLOSED status.
If the msk status transitions to TCP_CLOSE in the release callback
invoked by the worker's final release_sock(), such instance of the
workqueue will not take any action.
Additionally the MPTCP code prevents scheduling the worker once the
socket reaches the CLOSE status: such msk resources will be leaked.
The only code path that can trigger the above scenario is the
__mptcp_check_send_data_fin() in fallback mode.
Address the issue removing the special handling of fallback socket
in __mptcp_check_send_data_fin(), consolidating the state machine
for fallback and non fallback socket.
Since non-fallback sockets do not send and do not receive data_fin,
the mptcp code can update the msk internal status to match the next
step in the SM every time data fin (ack) should be generated or
received.
As a consequence we can remove a bunch of checks for fallback from
the fastpath.
Paolo Abeni [Tue, 20 Jun 2023 16:24:20 +0000 (18:24 +0200)]
mptcp: fix possible list corruption on passive MPJ
At passive MPJ time, if the msk socket lock is held by the user,
the new subflow is appended to the msk->join_list under the msk
data lock.
In mptcp_release_cb()/__mptcp_flush_join_list(), the subflows in
that list are moved from the join_list into the conn_list under the
msk socket lock.
Append and removal could race, possibly corrupting such list.
Address the issue splicing the join list into a temporary one while
still under the msk data lock.
Found by code inspection, the race itself should be almost impossible
to trigger in practice.
mptcp_recvmsg is allowed to release the msk socket lock when
blocking, and before re-acquiring it another thread could have
switched the sock to TCP_LISTEN status - with a prior
connect(AF_UNSPEC) - also clearing icsk_ack.rcv_mss.
Address the issue preventing the disconnect if some other process is
concurrently performing a blocking syscall on the same socket, alike
commit 4faeee0cf8a5 ("tcp: deny tcp_disconnect() when threads are waiting").
projects / linux.git / log