Resulting in DMCUB re-entering IPS after a disable and keeping the allow
high.
[How]
Long term we need to split commit/allow into two registers or use shared
DRAM state, but short term we can reduce the repro rate by ensuring that
the disallow went through by bounding the expected worst case scenario.
Alvin Lee [Tue, 12 Dec 2023 17:17:31 +0000 (12:17 -0500)]
drm/amd/display: For FPO and SubVP/DRR configs program vmin/max sel
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank in FPO / SubVP
/ DRR cases will not have any effect and we could hit underflow /
corruption.
[Why]
If bandwidth allocation feature is enabled, connection manager wont
limit the dp tunnel bandwidth. So, need to do display mode validation
for streams on dpia links to avoid oversubscription of dp tunnel
bandwidth.
[How]
- To read non reduced link rate and lane count and update
reported link capability.
- To calculate the bandwidth required for streams of dpia links
per host router and validate against the allocated bandwidth for
the host router.
drm/amd/display: Switch DMCUB notify idle command to NO_WAIT
[Why]
Race condition between notification of driver idle and the command being
processed. We could theoretically enter idle between the submission and
the wait for idle that occurs after.
[How]
Switch the notification to NO_WAIT to avoid the RPTR access.
Relja Vojvodic [Wed, 13 Dec 2023 15:31:06 +0000 (10:31 -0500)]
drm/amd/display: Add log end specifier
[Why]
Some debug tools, sometimes wrap around to multiple lines which causes
issues with the DPM test script while it is looking for the logs. Need a
way to tell when the log is finished.
Alvin Lee [Wed, 13 Dec 2023 14:46:50 +0000 (09:46 -0500)]
drm/amd/display: Assign stream status for FPO + Vactive cases
A new check was added to ensure FPO is not enabled when the FPO pipe has
0 planes. This requires the stream status to check the plane count, but
the stream status was not assigned for FPO + Vactive cases which leads
to FPO not be enabled always.
Felix Kuehling [Mon, 18 Dec 2023 21:17:23 +0000 (16:17 -0500)]
drm/amdgpu: Let KFD sync with VM fences
Change the rules for amdgpu_sync_resv to let KFD synchronize with VM
fences on page table reservations. This fixes intermittent memory
corruption after evictions when using amdgpu_vm_handle_moved to update
page tables for VM mappings managed through render nodes.
Wayne Lin [Mon, 4 Dec 2023 02:09:33 +0000 (10:09 +0800)]
drm/amd/display: pbn_div need be updated for hotplug event
link_rate sometime will be changed when DP MST connector hotplug, so
pbn_div also need be updated; otherwise, it will mismatch with
link_rate, causes no output in external monitor.
Camille Cho [Thu, 16 Nov 2023 08:19:25 +0000 (16:19 +0800)]
drm/amd/display: Correctly restore user_level
[Why]
BL1_PWM_USER_LEVEL is meant for the user brightness level setting from
OS. However, we update it along with other ABM levels to the real PWM
value which could be ABMed.
[How]
Driver to cache and restore the user brightness level setting so that
DMUB can retrieve the last user setting in ABM config initialization.
drm/amd/display: Fix minor issues in BW Allocation Phase2
[Why]
Fix minor issues in BW Allocation Phase2.
[How]
- In set_usb4_req_bw_req(), link->dpia_bw_alloc_config.response_ready
flag should be reset before writing DPCD REQUEST_BW.
- Fix the granularity for value of 2 in get_bw_granularity().
- Removed bandwidth allocation support display fw boot option as
the fw would read feature enable status from bios.
- Clean up DPIA_EST_BW_CHANGED and DPIA_BW_REQ_SUCCESS cases in
dpia_handle_bw_alloc_response().
- Removed allocate_usb4_bw and deallocate_usb4_bw.
- Optimized loop in get_lowest_dpia_index().
- Updated link_dp_dpia_allocate_usb4_bandwidth_for_stream() and
set_usb4_req_bw_req() to always issue request bw.
Josip Pavic [Mon, 11 Dec 2023 22:50:19 +0000 (17:50 -0500)]
drm/amd/display: Add null pointer guards where needed
[Why]
Some functions whose output is typically checked for null are not being
checked for null at several call sites, causing some static analysis
tools to throw an error.
[How]
Add null pointer guards around functions that typically have them at
other call sites.
Relja Vojvodic [Mon, 11 Dec 2023 23:00:14 +0000 (18:00 -0500)]
drm/amd/display: Add more mechanisms for tests
[Why]
More information is desired for the test tools.
[How]
Refactored get_subvp_visual_confirm_color and
get_mclk_switch_visual_confirm_color to support the new method of
storing the p_state type, which was changed so that it could also be
saved and output by the DPM log. Ensured that the p_state type is kept
updated by looping through the pipes within commit_planes_for_stream.
Alvin Lee [Mon, 11 Dec 2023 19:46:14 +0000 (14:46 -0500)]
drm/amd/display: Don't allow FPO if no planes
In DCN32/321 FPO uses per-pipe P-State force. If there is no plane, then
then HUBP is power gated, in which case any programming in HUBP has no
effect and the pipe is always asserting P-State allow. This is contrary
to what we want to happen for FPO (FW should moderate the P-State
assertion), so block FPO if there's no plane for the FPO pipe.
Colin Ian King [Tue, 19 Dec 2023 14:19:30 +0000 (14:19 +0000)]
drm/amd/display: remove redundant initialization of variable remainder
Variable remainder is being initialized with a value that is never read,
the assignment is redundant and can be removed. Also add a newline
after the declaration to clean up the coding style.
ZhenGuo Yin [Tue, 19 Dec 2023 06:39:42 +0000 (14:39 +0800)]
drm/amdgpu: re-create idle bo's PTE during VM state machine reset
Idle bo's PTE needs to be re-created when resetting VM state machine.
Set idle bo's vm_bo as moved to mark it as invalid.
Fixes: 55bf196f60df ("drm/amdgpu: reset VM when an error is detected") Signed-off-by: ZhenGuo Yin <[email protected]> Reviewed-by: Christian König <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
YiPeng Chai [Tue, 12 Dec 2023 09:23:23 +0000 (17:23 +0800)]
drm/amdgpu: Add umc page retirement for umc v12_0
Add umc page retirement for umc v12_0.
V2:
1. Changed umc page retirement check condition
to call umc_v12_0_is_uncorrectable_error.
2. Use memset to clear the contents of the umc
error address structure.
Aric Cyr [Mon, 11 Dec 2023 02:20:56 +0000 (21:20 -0500)]
drm/amd/display: 3.2.265
This DC patchset brings improvements in multiple areas. In summary, we highlight:
- change static screen wait frame_count for ips
- Fix hang/underflow when transitioning to ODM4:1
- Only clear symclk otg flag for HDMI
- Fix lightup regression with DP2 single display configs
- Refactor phantom resource allocation
- Refactor dc_state interface
- Wake DMCUB before executing GPINT commands
- Wake DMCUB before sending a command
- Refactor DMCUB enter/exit idle interface
- enable dcn35 idle power optimization
- fix usb-c connector_type
- add debug option for ExtendedVBlank DLG adjust
- Set test_pattern_changed update flag on pipe enable
- dereference variable before checking for zero
- get dprefclk ss info from integration info table
- skip error logging when DMUB is inactive from S3
- make flip_timestamp_in_us a 64-bit variable
- Add case for dcn35 to support usb4 dmub hpd event
- Add function for dumping clk registers
- Unify optimize_required flags and VRR adjustments
- Revert using channel_width as 2 for vram table 3.0
- remove HPO PG in driver side
- do not send commands to DMUB if DMUB is inactive from S3
Ilya Bakoulin [Fri, 8 Dec 2023 17:19:33 +0000 (12:19 -0500)]
drm/amd/display: Fix hang/underflow when transitioning to ODM4:1
[Why]
Under some circumstances, disabling an OPTC and attempting to reclaim
its OPP(s) for a different OPTC could cause a hang/underflow due to OPPs
not being properly disconnected from the disabled OPTC.
[How]
Ensure that all OPPs are unassigned from an OPTC when it gets disabled.
Alvin Lee [Fri, 8 Dec 2023 16:56:56 +0000 (11:56 -0500)]
drm/amd/display: Only clear symclk otg flag for HDMI
[Description]
There is a corner case where the symclk otg flag is cleared
when disabling the phantom pipe for subvp (because the phantom
and main pipe share the same link). This is undesired because
we need the maintain the correct symclk otg flag state for
the main pipe.
For now only clear the flag only for HDMI signal type, since
it's only set for HDMI signal type (phantom is virtual). The
ideal solution is to not clear it if the stream is phantom but
currently there's a bug that doesn't allow us to do this. Once
this issue is fixed the proper fix can be implemented.
Dillon Varone [Wed, 13 Dec 2023 20:04:42 +0000 (15:04 -0500)]
drm/amd/display: Create dc_state after resource initialization
[WHY&HOW]
After refactoring dc_state, it is always constructed at the time of its
creation. Construction can only happen after dc resources are initialized, so
move creation to be after this.
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Dillon Varone [Fri, 17 Nov 2023 21:37:50 +0000 (16:37 -0500)]
drm/amd/display: Refactor dc_state interface
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
drm/amd/display: Wake DMCUB before sending a command
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
For functions that execute within a DC context or DC lock we can
wrap the direct calls to dm_execute_dmub_cmd/list with code that
exits idle power optimizations and reallows once we're done with
the command submission on success.
For DM direct submissions the DM will need to manage the enter/exit
sequencing manually.
We cannot invoke a DMCUB command directly within the DM execution
helper or we can deadlock.
[Why]
We can hang in place trying to send commands when the DMCUB isn't
powered on.
[How]
We need to exit out of the idle state prior to sending a command,
but the process that performs the exit also invokes a command itself.
Fixing this issue involves the following:
1. Using a software state to track whether or not we need to start
the process to exit idle or notify idle.
It's possible for the hardware to have exited an idle state without
driver knowledge, but entering one is always restricted to a driver
allow - which makes the SW state vs HW state mismatch issue purely one
of optimization, which should seldomly be hit, if at all.
2. Refactor any instances of exit/notify idle to use a single wrapper
that maintains this SW state.
This works simialr to dc_allow_idle_optimizations, but works at the
DMCUB level and makes sure the state is marked prior to any notify/exit
idle so we don't enter an infinite loop.
3. Make sure we exit out of idle prior to sending any commands or
waiting for DMCUB idle.
This patch takes care of 1/2. A future patch will take care of wrapping
DMCUB command submission with calls to this new interface.
Allen Pan [Thu, 7 Dec 2023 22:26:10 +0000 (17:26 -0500)]
drm/amd/display: fix usb-c connector_type
[why]
BIOS switches to use USB-C connector type 0x18, but VBIOS's
objectInfo table not supported yet. driver needs to patch it
based on enc_cap from system integration info table.
George Shen [Tue, 5 Dec 2023 23:34:47 +0000 (18:34 -0500)]
drm/amd/display: Set test_pattern_changed update flag on pipe enable
[Why]
In certain cases, ODM pipe split can occur while stream already has test
pattern enabled. The new pipe used in the ODM combine config must be
configured to output the test pattern in this case.
[How]
If the stream is configured to output test pattern, then set the
test_pattern_changed update flag for the new pipe when it gets enabled.
Charlene Liu [Wed, 6 Dec 2023 22:14:48 +0000 (17:14 -0500)]
drm/amd/display: get dprefclk ss info from integration info table
[why & how]
we have two SSC_En:
we get ssc_info from dce_info for MPLL_SSC_EN.
we used to call VBIOS cmdtbl's smu_info's SS persentage for DPRECLK SS info,
is used for DP AUDIO and VBIOS' smu_info table was from systemIntegrationInfoTable.
since dcn35 VBIOS removed smu_info, driver need to use integrationInfotable directly.
Xiaogang Chen [Fri, 15 Dec 2023 23:14:07 +0000 (17:14 -0600)]
drm/amdkfd: Use partial hmm page walk during buffer validation in SVM
SVM uses hmm page walk to valid buffer before map to gpu vm. After have partial
migration/mapping do validation on same vm range as migration/map do instead of
whole svm range that can be very large. This change is expected to improve svm
code performance.
Josip Pavic [Tue, 5 Dec 2023 17:01:05 +0000 (12:01 -0500)]
drm/amd/display: make flip_timestamp_in_us a 64-bit variable
[Why]
This variable currently overflows after about 71 minutes. This doesn't
cause any known functional issues but it does make debugging more
difficult.
Wayne Lin [Tue, 5 Dec 2023 06:55:31 +0000 (14:55 +0800)]
drm/amd/display: Add case for dcn35 to support usb4 dmub hpd event
[Why & how]
Refactor dc_is_dmub_outbox_supported() a bit and add case for dcn35 to
register dmub outbox notification irq to handle usb4 relevant hpd event.
Hamza Mahfooz [Fri, 15 Dec 2023 15:37:39 +0000 (10:37 -0500)]
drm/amd/display: disable FPO and SubVP for older DMUB versions on DCN32x
There have recently been changes that break backwards compatibility,
that were introduced into DMUB firmware (for DCN32x) concerning FPO and
SubVP. So, since those are just power optimization features, we can just
disable them unless the user is using a new enough version of DMUB
firmware.
drm/amd/display: Add a new DC debug mask for PSR-SU
Some issues have been raised that appear to be tied to PSR-SU.
To allow users to confirm they're tied to PSR-SU without turning off
PSR entirely introduce a new debug mask:
Aric Cyr [Thu, 30 Nov 2023 23:54:48 +0000 (18:54 -0500)]
drm/amd/display: Unify optimize_required flags and VRR adjustments
[why]
There is only a single call to dc_post_update_surfaces_to_stream so
there is no need to have two flags to control it. Unifying this to a
single flag allows dc_stream_adjust_vmin_vmax to skip actual
programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Alvin Lee [Mon, 4 Dec 2023 20:19:34 +0000 (15:19 -0500)]
drm/amd/display: Revert " drm/amd/display: Use channel_width = 2 for vram table 3.0"
[Description]
Revert commit fec05adc40c2 ("drm/amd/display: Use channel_width = 2 for vram table 3.0")
Because the issue is being fixed from VBIOS side.
James Zhu [Fri, 8 Dec 2023 22:41:25 +0000 (17:41 -0500)]
drm/amdgpu: increase hmm range get pages timeout
When application tries to allocate all system memory and cause memory
to swap out. Needs more time for hmm_range_fault to validate the
remaining page for allocation. To be safe, increase timeout value to
1 second for 64MB range.
Philip Yang [Thu, 14 Dec 2023 14:42:03 +0000 (09:42 -0500)]
drm/amdkfd: svm range always mapped flag not working on APU
On gfx943 APU there is no VRAM and page migration, queue CWSR area, svm
range with always mapped flag, is not mapped to GPU correctly. This
works fine if retry fault on CWSR area can be recovered, but could cause
deadlock if there is another retry fault recover waiting for CWSR to
finish.
Fix this by mapping svm range with always mapped flag to GPU with ACCESS
attribute if XNACK ON.
There is side effect, because all GPUs have ACCESS attribute by default
on new svm range with XNACK on, the CWSR area will be mapped to all GPUs
after this change. This side effect will be fixed with Thunk change to
set CWSR svm range with ACCESS_IN_PLACE attribute on the GPU that user
queue is created.
Jonathan Kim [Thu, 14 Dec 2023 03:08:03 +0000 (22:08 -0500)]
drm/amdkfd: only flush mes process context if mes support is there
Fix up on mes process context flush to prevent non-mes devices from
spamming error messages or running into undefined behaviour during
process termination.
Fixes: bd33bb1409b4 ("drm/amdkfd: fix mes set shader debugger process management") Signed-off-by: Jonathan Kim <[email protected]> Reviewed-by: Eric Huang <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Zhipeng Lu [Thu, 14 Dec 2023 16:59:38 +0000 (00:59 +0800)]
drm/amd/pm: fix a double-free in amdgpu_parse_extended_power_table
The amdgpu_free_extended_power_table is called in every error-handling
paths of amdgpu_parse_extended_power_table. However, after the following
call chain of returning:
amdgpu_parse_extended_power_table
|-> kv_dpm_init / si_dpm_init
(the only two caller of amdgpu_parse_extended_power_table)
|-> kv_dpm_sw_init / si_dpm_sw_init
(the only caller of kv_dpm_init / si_dpm_init, accordingly)
|-> kv_dpm_fini / si_dpm_fini
(goto dpm_failed in xx_dpm_sw_init)
|-> amdgpu_free_extended_power_table
As above, the amdgpu_free_extended_power_table is called twice in this
returning chain and thus a double-free is triggered. Similarily, the
last kfree in amdgpu_parse_extended_power_table also cause a double free
with amdgpu_free_extended_power_table in kv_dpm_fini.
Fixes: 84176663e70d ("drm/amd/pm: create a new holder for those APIs used only by legacy ASICs(si/kv)") Signed-off-by: Zhipeng Lu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Zhipeng Lu [Thu, 14 Dec 2023 16:58:42 +0000 (00:58 +0800)]
gpu/drm/radeon: fix two memleaks in radeon_vm_init
When radeon_bo_create and radeon_vm_clear_bo fail, the vm->page_tables
allocated before need to be freed. However, neither radeon_vm_init
itself nor its caller have done such deallocation.
Fixes: 6d2f2944e95e ("drm/radeon: use normal BOs for the page tables v4") Signed-off-by: Zhipeng Lu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Zhipeng Lu [Thu, 14 Dec 2023 16:24:58 +0000 (00:24 +0800)]
drivers/amd/pm: fix a use-after-free in kv_parse_power_table
When ps allocated by kzalloc equals to NULL, kv_parse_power_table
frees adev->pm.dpm.ps that allocated before. However, after the control
flow goes through the following call chains:
The adev->pm.dpm.ps is used in the for loop of kv_dpm_fini after its
first free in kv_parse_power_table and causes a use-after-free bug.
Fixes: a2e73f56fa62 ("drm/amdgpu: Add support for CIK parts") Signed-off-by: Zhipeng Lu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Zhipeng Lu [Thu, 14 Dec 2023 15:24:11 +0000 (23:24 +0800)]
drm/amd/pm: fix a double-free in si_dpm_init
When the allocation of
adev->pm.dpm.dyn_state.vddc_dependency_on_dispclk.entries fails,
amdgpu_free_extended_power_table is called to free some fields of adev.
However, when the control flow returns to si_dpm_sw_init, it goes to
label dpm_failed and calls si_dpm_fini, which calls
amdgpu_free_extended_power_table again and free those fields again. Thus
a double-free is triggered.
Fixes: 841686df9f7d ("drm/amdgpu: add SI DPM support (v4)") Signed-off-by: Zhipeng Lu <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Alex Deucher [Mon, 27 Nov 2023 22:26:29 +0000 (17:26 -0500)]
drm/amdgpu/debugfs: fix error code when smc register accessors are NULL
Should be -EOPNOTSUPP.
Fixes: 5104fdf50d32 ("drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL") Reviewed-by: Christian König <[email protected]> Signed-off-by: Alex Deucher <[email protected]>
Melissa Wen [Thu, 16 Nov 2023 19:58:11 +0000 (18:58 -0100)]
drm/amd/display: add plane CTM support
Map the plane CTM driver-specific property to DC plane, instead of DC
stream. The remaining steps to program DPP block are already implemented
on DC shared-code.
v3:
- fix comment about plane and CRTC CTMs priorities (Harry)
Plane CTM for pre-blending color space conversion. Only enable
driver-specific plane CTM property on drivers that support both pre- and
post-blending gamut remap matrix, i.e., DCN3+ family. Otherwise it
conflits with DRM CRTC CTM property.
Wang, Beyond [Tue, 12 Dec 2023 13:03:04 +0000 (21:03 +0800)]
drm/amdgpu: fix ftrace event amdgpu_bo_move always move on same heap
Issue: during evict or validate happened on amdgpu_bo, the 'from' and
'to' is always same in ftrace event of amdgpu_bo_move
where calling the 'trace_amdgpu_bo_move', the comment says move_notify
is called before move happens, but actually it is called after move
happens, here the new_mem is same as bo->resource
Fix: move trace_amdgpu_bo_move from move_notify to amdgpu_bo_move
Joshua Ashton [Thu, 16 Nov 2023 19:58:07 +0000 (18:58 -0100)]
drm/amd/display: add plane blend LUT and TF support
Map plane blend properties to DPP blend gamma. Plane blend is a
post-3D LUT curve that linearizes color space for blending. It may be
defined by a user-blob LUT and/or predefined transfer function. As
hardcoded curve (ROM) is not supported on blend gamma, we use AMD color
module to fill parameters when setting non-linear TF with empty LUT.
Joshua Ashton [Thu, 16 Nov 2023 19:58:06 +0000 (18:58 -0100)]
drm/amd/display: handle empty LUTs in __set_input_tf
Unlike degamma, blend gamma doesn't support hardcoded curve
(predefined/ROM), but we can use AMD color module to fill blend gamma
parameters when we have non-linear plane gamma TF without plane gamma
LUT. The regular degamma path doesn't hit this.
Melissa Wen [Thu, 16 Nov 2023 19:58:05 +0000 (18:58 -0100)]
drm/amd/display: add plane 3D LUT support
Wire up DC 3D LUT to DM plane color management (pre-blending). On AMD
display HW, 3D LUT comes after a shaper curve and we always have to
program a shaper curve to delinearize or normalize the color space
before applying a 3D LUT (since we have a reduced number of LUT
entries).
In this version, the default values of 3D LUT for size and bit_depth are
17x17x17 and 12-bit, but we already provide here a more generic
mechanisms to program other supported values (9x9x9 size and 10-bit).
v2:
- started with plane 3D LUT instead of CRTC 3D LUT support
v4:
- lut3d_size is the max dimension size instead of # of entries
Woody Suwalski [Tue, 12 Dec 2023 23:31:34 +0000 (18:31 -0500)]
drm/radeon: Prevent multiple debug error lines on suspend
Fix to avoid multiple debug error lines printed on every suspend by Radeon driver's debugfs.
radeon_debugfs_init() calls debugfs_create_file() for every ring.
This results in printing multiple error lines to the screen and dmesg similar to this:
[ 92.378726] debugfs: File 'radeon_ring_gfx' in directory '0000:00:01.0' already present!
[ 92.378732] debugfs: File 'radeon_ring_cp1' in directory '0000:00:01.0' already present!
[ 92.378734] debugfs: File 'radeon_ring_cp2' in directory '0000:00:01.0' already present!
[ 92.378737] debugfs: File 'radeon_ring_dma1' in directory '0000:00:01.0' already present!
[ 92.378739] debugfs: File 'radeon_ring_dma2' in directory '0000:00:01.0' already present!
[ 92.380775] debugfs: File 'radeon_ring_uvd' in directory '0000:00:01.0' already present!
[ 92.406620] debugfs: File 'radeon_ring_vce1' in directory '0000:00:01.0' already present!
[ 92.406624] debugfs: File 'radeon_ring_vce2' in directory '0000:00:01.0' already present!
Patch v1: The fix was to run lookup() for the file before trying to (re)create that debug file.
Patch v2: Call the radeon_debugfs_init() only once when radeon ring is initialized (as suggested
by Christian K. - thanks)
Melissa Wen [Thu, 16 Nov 2023 19:58:04 +0000 (18:58 -0100)]
drm/amd/display: add plane shaper TF support
Enable usage of predefined transfer func in addition to shaper 1D LUT.
That means we can save some complexity by just setting a predefined
curve, instead of programming a custom curve when preparing color space
for applying 3D LUT.
Melissa Wen [Thu, 16 Nov 2023 19:58:03 +0000 (18:58 -0100)]
drm/amd/display: add plane shaper LUT support
Map DC shaper LUT to DM plane color management. Shaper LUT can be used
to delinearize and/or normalize the color space for computational
efficiency and achiving specific visual styles. If a plane degamma is
apply to linearize the color space, a custom shaper 1D LUT can be used
just before applying 3D LUT.
v2:
- use DPP color caps to verify plane 3D LUT support
- add debug message if shaper LUT programming fails
v4:
- remove helper to check 3D LUT color caps (Harry)
- update desc of lut3d-setup helper from MPC to DPP
v5:
- remove color_mgmt_changed check that prevents color updates (Joshua)
Melissa Wen [Thu, 16 Nov 2023 19:58:00 +0000 (18:58 -0100)]
drm/amd/display: reject atomic commit if setting both plane and CRTC degamma
DC only has pre-blending degamma caps (plane/DPP) that is currently in
use for CRTC/post-blending degamma, so that we don't have HW caps to
perform plane and CRTC degamma at the same time. Reject atomic updates
when serspace sets both plane and CRTC degamma properties.
Joshua Ashton [Thu, 16 Nov 2023 19:57:59 +0000 (18:57 -0100)]
drm/amd/display: add plane degamma TF and LUT support
Set DC plane with user degamma LUT or predefined TF from driver-specific
plane color properties. If plane and CRTC degamma are set in the same
time, plane degamma has priority. That means, we only set CRTC degamma
if we don't have plane degamma LUT or TF to configure. We return -EINVAL
if we don't have plane degamma settings, so we can continue and check
CRTC degamma.
Christian König [Fri, 8 Dec 2023 12:43:09 +0000 (13:43 +0100)]
drm/amdgpu: fix tear down order in amdgpu_vm_pt_free
When freeing PD/PT with shadows it can happen that the shadow
destruction races with detaching the PD/PT from the VM causing a NULL
pointer dereference in the invalidation code.
Fix this by detaching the the PD/PT from the VM first and then
freeing the shadow instead.
Melissa Wen [Thu, 16 Nov 2023 19:57:58 +0000 (18:57 -0100)]
drm/amd/display: decouple steps for mapping CRTC degamma to DC plane
The next patch adds pre-blending degamma to AMD color mgmt pipeline, but
pre-blending degamma caps (DPP) is currently in use to provide DRM CRTC
atomic degamma or implict degamma on legacy gamma. Detach degamma usage
regarging CRTC color properties to manage plane and CRTC color
correction combinations.
projects / linux.git / log