Johannes Berg [Wed, 24 Aug 2022 10:37:32 +0000 (12:37 +0200)]
wifi: mac80211: allow link address A2 in TXQ dequeue
In ieee80211_tx_dequeue() we currently allow a control port
frame to be transmitted on a non-authorized port only if the
A2 matches the local interface address, but if that's an MLD
and the peer is a legacy peer, we need to allow link address
here. Fix that.
Johannes Berg [Wed, 24 Aug 2022 10:30:16 +0000 (12:30 +0200)]
wifi: mac80211: fix control port frame addressing
For an AP interface, when userspace specifieds the link ID to
transmit the control port frame on (in particular for the
initial 4-way-HS), due to the logic in ieee80211_build_hdr()
for a frame transmitted from/to an MLD, we currently build a
header with
A1 = DA = MLD address of the peer MLD
A2 = local link address (!)
A3 = SA = local MLD address
This clearly makes no sense, and leads to two problems:
- if the frame were encrypted (not true for the initial
4-way-HS) the AAD would be calculated incorrectly
- if iTXQs are used, the frame is dropped by logic in
ieee80211_tx_dequeue()
Fix the addressing, which fixes the first bullet, and the
second bullet for peer MLDs, I'll fix the second one for
non-MLD peers separately.
Johannes Berg [Fri, 19 Aug 2022 12:58:42 +0000 (14:58 +0200)]
wifi: mac80211_hwsim: fix link change handling
The code for determining which links to update in wmediumd
or virtio was wrong, fix it to remove the deflink only if
there were no old links, and also add the deflink if there
are no other new links.
Fixes: c204d9df0202 ("wifi: mac80211_hwsim: handle links for wmediumd/virtio") Signed-off-by: Johannes Berg <[email protected]>
For AP/non-AP the EHT MCS/NSS subfield size differs, the
4-octet subfield is only used for 20 MHz-only non-AP STA.
Pass an argument around everywhere to be able to parse it
properly.
Johannes Berg [Tue, 16 Aug 2022 09:22:46 +0000 (11:22 +0200)]
wifi: mac80211_hwsim: split iftype data into AP/non-AP
The next patch will require splitting the data here into
AP and non-AP because for EHT, the format of the MCS/NSS
support (struct ieee80211_eht_mcs_nss_supp) is different,
for AP the only_20mhz cannot be used.
Draft P802.11be_D2.1, section 35.3.17 states that the EML Capabilities
Field shouldn't be included in case the device doesn't have support for
EMLSR or EMLMR.
Fixes: 81151ce462e5 ("wifi: mac80211: support MLO authentication/association with one link") Signed-off-by: Mordechay Goodstein <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
Johannes Berg [Wed, 17 Aug 2022 19:57:19 +0000 (21:57 +0200)]
wifi: mac80211: use link ID for MLO in queued frames
When queuing frames to an interface store the link ID we
determined (which possibly came from the driver in the
RX status in the first place) in the RX status, and use
it in the MLME code to send probe responses, beacons and
CSA frames to the right link.
wifi: mac80211: add link information in ieee80211_rx_status
In MLO, when the address translation from link to MLD is done
in fw/hw, it is necessary to be able to have some information
on the link on which the frame has been received. Extend the
rx API to include link_id and a valid flag in ieee80211_rx_status.
Also make chanes to mac80211 rx APIs to make use of the reported
link_id after sanity checks.
wifi: cfg80211: Add link_id parameter to various key operations for MLO
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
wifi: cfg80211: Prevent cfg80211_wext_siwencodeext() on MLD
Currently, MLO support is not added for WEXT code and WEXT handlers are
prevented on MLDs. Prevent WEXT handler cfg80211_wext_siwencodeext()
also on MLD which is missed in commit 7b0a0e3c3a88 ("wifi: cfg80211: do
some rework towards MLO link APIs")
Shaul Triebitz [Mon, 1 Aug 2022 11:12:29 +0000 (14:12 +0300)]
wifi: cfg80211: get correct AP link chandef
When checking for channel regulatory validity, use the
AP link chandef (and not mesh's chandef).
Fixes: 7b0a0e3c3a88 ("wifi: cfg80211: do some rework towards MLO link APIs") Signed-off-by: Shaul Triebitz <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
Ilan Peer [Wed, 3 Aug 2022 15:02:56 +0000 (18:02 +0300)]
wifi: cfg80211: Update RNR parsing to align with Draft P802.11be_D2.0
Based on changes in the specification the TBTT information in
the RNR can include MLD information, so update the parsing to
allow extracting the short SSID information in such a case.
Johannes Berg [Sat, 23 Jul 2022 20:08:49 +0000 (22:08 +0200)]
wifi: mac80211: accept STA changes without link changes
If there's no link ID, then check that there are no changes to
the link, and if so accept them, unless a new link is created.
While at it, reject creating a new link without an address.
This fixes authorizing an MLD (peer) that has no link 0.
Richard Gobert [Tue, 23 Aug 2022 07:10:49 +0000 (09:10 +0200)]
net: gro: skb_gro_header helper function
Introduce a simple helper function to replace a common pattern.
When accessing the GRO header, we fetch the pointer from frag0,
then test its validity and fetch it from the skb when necessary.
This leads to the pattern
skb_gro_header_fast -> skb_gro_header_hard -> skb_gro_header_slow
recurring many times throughout GRO code.
This patch replaces these patterns with a single inlined function
call, improving code readability.
====================
Add a second bind table hashed by port and address
Currently, there is one bind hashtable (bhash) that hashes by port only.
This patchset adds a second bind table (bhash2) that hashes by port and
address.
The motivation for adding bhash2 is to expedite bind requests in situations
where the port has many sockets in its bhash table entry (eg a large number
of sockets bound to different addresses on the same port), which makes checking
bind conflicts costly especially given that we acquire the table entry spinlock
while doing so, which can cause softirq cpu lockups and can prevent new tcp
connections.
We ran into this problem at Meta where the traffic team binds a large number
of IPs to port 443 and the bind() call took a significant amount of time
which led to cpu softirq lockups, which caused packet drops and other failures
on the machine.
When experimentally testing this on a local server for ~24k sockets bound to
the port, the results seen were:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds
ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
The additions to the initial bhash2 submission [0] are:
* Updating bhash2 in the cases where a socket's rcv saddr changes after it has
* been bound
* Adding locks for bhash2 hashbuckets
Joanne Koong [Mon, 22 Aug 2022 18:10:23 +0000 (11:10 -0700)]
selftests/net: Add sk_bind_sendto_listen and sk_connect_zero_addr
This patch adds 2 new tests: sk_bind_sendto_listen and
sk_connect_zero_addr.
The sk_bind_sendto_listen test exercises the path where a socket's
rcv saddr changes after it has been added to the binding tables,
and then a listen() on the socket is invoked. The listen() should
succeed.
The sk_bind_sendto_listen test is copied over from one of syzbot's
tests: https://syzkaller.appspot.com/x/repro.c?x=1673a38df00000
The sk_connect_zero_addr test exercises the path where the socket was
never previously added to the binding tables and it gets assigned a
saddr upon a connect() to address 0.
Joanne Koong [Mon, 22 Aug 2022 18:10:22 +0000 (11:10 -0700)]
selftests/net: Add test for timing a bind request to a port with a populated bhash entry
This test populates the bhash table for a given port with
MAX_THREADS * MAX_CONNECTIONS sockets, and then times how long
a bind request on the port takes.
When populating the bhash table, we create the sockets and then bind
the sockets to the same address and port (SO_REUSEADDR and SO_REUSEPORT
are set). When timing how long a bind on the port takes, we bind on a
different address without SO_REUSEPORT set. We do not set SO_REUSEPORT
because we are interested in the case where the bind request does not
go through the tb->fastreuseport path, which is fragile (eg
tb->fastreuseport path does not work if binding with a different uid).
To run the script:
Usage: ./bind_bhash.sh [-6 | -4] [-p port] [-a address]
6: use ipv6
4: use ipv4
port: Port number
address: ip address
Without any arguments, ./bind_bhash.sh defaults to ipv6 using ip address
"2001:0db8:0:f101::1" on port 443.
On my local machine, I see:
ipv4:
before - 0.002317 seconds
with bhash2 - 0.000020 seconds
ipv6:
before - 0.002431 seconds
with bhash2 - 0.000021 seconds
Joanne Koong [Mon, 22 Aug 2022 18:10:21 +0000 (11:10 -0700)]
net: Add a bhash2 table hashed by port and address
The current bind hashtable (bhash) is hashed by port only.
In the socket bind path, we have to check for bind conflicts by
traversing the specified port's inet_bind_bucket while holding the
hashbucket's spinlock (see inet_csk_get_port() and
inet_csk_bind_conflict()). In instances where there are tons of
sockets hashed to the same port at different addresses, the bind
conflict check is time-intensive and can cause softirq cpu lockups,
as well as stops new tcp connections since __inet_inherit_port()
also contests for the spinlock.
This patch adds a second bind table, bhash2, that hashes by
port and sk->sk_rcv_saddr (ipv4) and sk->sk_v6_rcv_saddr (ipv6).
Searching the bhash2 table leads to significantly faster conflict
resolution and less time holding the hashbucket spinlock.
Please note a few things:
* There can be the case where the a socket's address changes after it
has been bound. There are two cases where this happens:
1) The case where there is a bind() call on INADDR_ANY (ipv4) or
IPV6_ADDR_ANY (ipv6) and then a connect() call. The kernel will
assign the socket an address when it handles the connect()
2) In inet_sk_reselect_saddr(), which is called when rebuilding the
sk header and a few pre-conditions are met (eg rerouting fails).
In these two cases, we need to update the bhash2 table by removing the
entry for the old address, and add a new entry reflecting the updated
address.
* The bhash2 table must have its own lock, even though concurrent
accesses on the same port are protected by the bhash lock. Bhash2 must
have its own lock to protect against cases where sockets on different
ports hash to different bhash hashbuckets but to the same bhash2
hashbucket.
This brings up a few stipulations:
1) When acquiring both the bhash and the bhash2 lock, the bhash2 lock
will always be acquired after the bhash lock and released before the
bhash lock is released.
2) There are no nested bhash2 hashbucket locks. A bhash2 lock is always
acquired+released before another bhash2 lock is acquired+released.
* The bhash table cannot be superseded by the bhash2 table because for
bind requests on INADDR_ANY (ipv4) or IPV6_ADDR_ANY (ipv6), every socket
bound to that port must be checked for a potential conflict. The bhash
table is the only source of port->socket associations.
1) Fix crash with malformed ebtables blob which do not provide all
entry points, from Florian Westphal.
2) Fix possible TCP connection clogging up with default 5-days
timeout in conntrack, from Florian.
3) Fix crash in nf_tables tproxy with unsupported chains, also from Florian.
4) Do not allow to update implicit chains.
5) Make table handle allocation per-netns to fix data race.
6) Do not truncated payload length and offset, and checksum offset.
Instead report EINVAl.
7) Enable chain stats update via static key iff no error occurs.
8) Restrict osf expression to ip, ip6 and inet families.
9) Restrict tunnel expression to netdev family.
10) Fix crash when trying to bind again an already bound chain.
11) Flowtable garbage collector might leave behind pending work to
delete entries. This patch comes with a previous preparation patch
as dependency.
12) Allow net.netfilter.nf_conntrack_frag6_high_thresh to be lowered,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_defrag_ipv6: allow nf_conntrack_frag6_high_thresh increases
netfilter: flowtable: fix stuck flows on cleanup due to pending work
netfilter: flowtable: add function to invoke garbage collection immediately
netfilter: nf_tables: disallow binding to already bound chain
netfilter: nft_tunnel: restrict it to netdev family
netfilter: nft_osf: restrict osf to ipv4, ipv6 and inet families
netfilter: nf_tables: do not leave chain stats enabled on error
netfilter: nft_payload: do not truncate csum_offset and csum_type
netfilter: nft_payload: report ERANGE for too long offset and length
netfilter: nf_tables: make table handle allocation per-netns friendly
netfilter: nf_tables: disallow updates of implicit chain
netfilter: nft_tproxy: restrict to prerouting hook
netfilter: conntrack: work around exceeded receive window
netfilter: ebtables: reject blobs that don't provide all entry points
====================
Randy Dunlap [Wed, 24 Aug 2022 02:42:16 +0000 (19:42 -0700)]
net: ethernet: ti: davinci_mdio: fix build for mdio bitbang uses
davinci_mdio.c uses mdio bitbang APIs, so it should select
MDIO_BITBANG to prevent build errors.
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_remove':
drivers/net/ethernet/ti/davinci_mdio.c:649: undefined reference to `free_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:545: undefined reference to `alloc_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_read':
drivers/net/ethernet/ti/davinci_mdio.c:236: undefined reference to `mdiobb_read'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_write':
drivers/net/ethernet/ti/davinci_mdio.c:253: undefined reference to `mdiobb_write'
i40e: Fix incorrect address type for IPv6 flow rules
It was not possible to create 1-tuple flow director
rule for IPv6 flow type. It was caused by incorrectly
checking for source IP address when validating user provided
destination IP address.
Fix this by changing ip6src to correct ip6dst address
in destination IP address validation for IPv6 flow type.
Fixes: efca91e89b67 ("i40e: Add flow director support for IPv6") Signed-off-by: Sylwester Dziedziuch <[email protected]> Tested-by: Gurucharan <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]>
Jacob Keller [Tue, 2 Aug 2022 00:24:19 +0000 (17:24 -0700)]
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
The ixgbe_ptp_start_cyclecounter is intended to be called whenever the
cyclecounter parameters need to be changed.
Since commit a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x
devices"), this function has cleared the SYSTIME registers and reset the
TSAUXC DISABLE_SYSTIME bit.
While these need to be cleared during ixgbe_ptp_reset, it is wrong to clear
them during ixgbe_ptp_start_cyclecounter. This function may be called
during both reset and link status change. When link changes, the SYSTIME
counter is still operating normally, but the cyclecounter should be updated
to account for the possibly changed parameters.
Clearing SYSTIME when link changes causes the timecounter to jump because
the cycle counter now reads zero.
Extract the SYSTIME initialization out to a new function and call this
during ixgbe_ptp_reset. This prevents the timecounter adjustment and avoids
an unnecessary reset of the current time.
This also restores the original SYSTIME clearing that occurred during
ixgbe_ptp_reset before the commit above.
Linus Torvalds [Wed, 24 Aug 2022 17:43:34 +0000 (10:43 -0700)]
Merge tag 'trace-v6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
- Fix build warning for when MODULES and FTRACE_WITH_DIRECT_CALLS are
not set. A warning happens with ops_references_rec() defined but not
used.
* tag 'trace-v6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix build warning for ops_references_rec() not used
Allow to configure port split options using the devlink port split
interface. Support port splitting only for port 0, as the FW has
a predefined set of available port split options for the whole device.
Add ice_devlink_port_options_print() function to print the table with
all available FW port split options. It will be printed after each port
split and unsplit command.
Add documentation for devlink port split interface usage for the ice
driver.
Jacob Keller [Thu, 11 Aug 2022 13:05:34 +0000 (15:05 +0200)]
ice: Add additional flags to ice_nvm_write_activate
The ice_nvm_write_activate function is used to issue AdminQ command
0x0707 which sends a request to firmware to activate a flash bank. For
basic operations, this command takes an 8bit flag value which defines
the flags to control the activation process. There are some additional
flags that are stored in a second 8bit flag field.
We can simplify the interface by using a u16 cmd_flags variable. Split
this over the two bytes of flag storage in the structure.
Implement support for Get/Set Port Options admin queue commands
(0x06EA/0x06EB). These firmware commands allow the driver to change port
specific options and will be used in the next patch.
Marcin Szycik [Fri, 29 Jul 2022 11:03:37 +0000 (13:03 +0200)]
ice: Add support for ip TTL & ToS offload
Add support for parsing TTL and ToS (Hop Limit and Traffic Class) tc fields
and matching on those fields in filters. Incomplete part of implementation
was already in place (getting enc_ip and enc_tos from flow_match_ip and
writing them to filter header).
Note: matching on ipv6 ip_ttl, enc_ttl and enc_tos is currently not
supported by the DDP package.
David S. Miller [Wed, 24 Aug 2022 12:46:59 +0000 (13:46 +0100)]
Merge branch 'sysctl-data-races'
Kuniyuki Iwashima says:
====================
net: sysctl: Fix data-races around net.core.XXX
This series fixes data-races around all knobs in net_core_table and
netns_core_table except for bpf stuff.
These knobs are skipped:
- 4 bpf knobs
- netdev_rss_key: Written only once by net_get_random_once() and
read-only knob
- rps_sock_flow_entries: Protected with sock_flow_mutex
- flow_limit_cpu_bitmap: Protected with flow_limit_update_mutex
- flow_limit_table_len: Protected with flow_limit_update_mutex
- default_qdisc: Protected with qdisc_mod_lock
- warnings: Unused
- high_order_alloc_disable: Protected with static_key_mutex
- skb_defer_max: Already using READ_ONCE()
- sysctl_txrehash: Already using READ_ONCE()
Note 5th patch fixes net.core.message_cost and net.core.message_burst,
and lib/ratelimit.c does not have an explicit maintainer.
Changes:
v3:
* Fix build failures of CONFIG_SYSCTL=n case in 13th & 14th patches
While reading gro_normal_batch, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 323ebb61e32b ("net: use listified RX for handling GRO_NORMAL skbs") Signed-off-by: Kuniyuki Iwashima <[email protected]> Acked-by: Edward Cree <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: Fix data-races around sysctl_devconf_inherit_init_net.
While reading sysctl_devconf_inherit_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 856c395cfa63 ("net: introduce a knob to control whether to inherit devconf config") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
While reading sysctl_fb_tunnels_only_for_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 79134e6ce2c9 ("net: do not create fallback tunnels for non-default namespaces") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
While reading netdev_budget_usecs, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 7acf8a1e8a28 ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
While reading sysctl_max_skb_frags, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 5f74f82ea34c ("net:Add sysctl_max_skb_frags") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
While reading netdev_budget, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 51b0bdedb8e7 ("[NET]: Separate two usages of netdev_max_backlog.") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: Fix a data-race around sysctl_tstamp_allow_data.
While reading sysctl_tstamp_allow_data, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: b245be1f4db1 ("net-timestamp: no-payload only sysctl") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
While reading rs->interval and rs->burst, they can be changed
concurrently via sysctl (e.g. net_ratelimit_state). Thus, we
need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: Fix data-races around weight_p and dev_weight_[rt]x_bias.
While reading weight_p, it can be changed concurrently. Thus, we need
to add READ_ONCE() to its reader.
Also, dev_[rt]x_weight can be read/written at the same time. So, we
need to use READ_ONCE() and WRITE_ONCE() for its access. Moreover, to
use the same weight_p while changing dev_[rt]x_weight, we add a mutex
in proc_do_dev_weight().
Fixes: 3d48b53fb2ae ("net: dev_weight: TX/RX orthogonality") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Wed, 24 Aug 2022 12:24:10 +0000 (13:24 +0100)]
Merge branch 'r8169-next'
Heiner Kallweit says:
====================
r8169: remove support for few unused chip versions
There's a number of chip versions that apparently never made it to the
mass market. Detection of these chip versions has been disabled for
few kernel versions now and nobody complained. Therefore remove
support for these chip versions.
====================
David S. Miller [Wed, 24 Aug 2022 12:19:39 +0000 (13:19 +0100)]
Merge tag 'mlx5-updates-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2022-08-22
Roi Dayan Says:
===============
Add support for SF tunnel offload
Mlx5 driver only supports VF tunnel offload.
To add support for SF tunnel offload the driver needs to:
1. Add send-to-vport metadata matching rules like done for VFs.
2. Set an indirect table for SF vport, same as VF vport.
info smaller sub functions for better maintainability.
rules from esw init phase to representor load phase.
SFs could be created after esw initialized and thus the send-to-vport
meta rules would not be created for those SFs.
By moving the creation of the rules to representor load phase
we ensure creating the rules also for SFs created later.
===============
Lama Kayal Says:
================
Make flow steering API loosely coupled from mlx5e_priv, in a manner to
introduce more readable and maintainable modules.
Make TC's private, let mlx5e_flow_steering struct be dynamically allocated,
and introduce its API to maintain the code via setters and getters
instead of publicly exposing it.
Introduce flow steering debug macros to provide an elegant finish to the
decoupled flow steering API, where errors related to flow steering shall
be reported via them.
All flow steering related files will drop any coupling to mlx5e_priv,
instead they will get the relevant members as input. Among these,
fs_tt_redirect, fs_tc, and arfs.
================
Jerry Ray [Mon, 22 Aug 2022 21:39:32 +0000 (16:39 -0500)]
micrel: ksz8851: fixes struct pointer issue
Issue found during code review. This bug has no impact as long as the
ks8851_net structure is the first element of the ks8851_net_spi structure.
As long as the offset to the ks8851_net struct is zero, the container_of()
macro is subtracting 0 and therefore no damage done. But if the
ks8851_net_spi struct is ever modified such that the ks8851_net struct
within it is no longer the first element of the struct, then the bug would
manifest itself and cause problems.
struct ks8851_net is contained within ks8851_net_spi.
ks is contained within kss.
kss is the priv_data of the netdev structure.
Oleksandr Mazur [Mon, 22 Aug 2022 18:03:15 +0000 (21:03 +0300)]
net: marvell: prestera: implement br_port_locked flag offloading
Both <port> br_port_locked and <lag> interfaces's flag
offloading is supported. No new ABI is being added,
rather existing (port_param_set) API call gets extended.
Signed-off-by: Oleksandr Mazur <[email protected]>
V2:
add missing receipents (linux-kernel, netdev) Signed-off-by: David S. Miller <[email protected]>
Csókás Bence [Mon, 22 Aug 2022 08:10:52 +0000 (10:10 +0200)]
fec: Restart PPS after link state change
On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.
Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`
David S. Miller [Wed, 24 Aug 2022 08:52:04 +0000 (09:52 +0100)]
Merge branch 'j7200-support'
Siddharth Vadapalli says:
====================
J7200: CPSW5G: Add support for QSGMII mode to am65-cpsw driver
Add support for QSGMII mode to am65-cpsw driver.
Change log:
v4-> v5:
1. Move ti,j7200-cpswxg-nuss compatible to the line above the
ti,j721e-cpsw-nuss compatible.
2. Add allOf and move if-then statements within it to allow future if-then
statements to be added easily.
v3 -> v4:
1. Update bindings to disallow ports based on compatible, instead of
adding a new if/then statement for the new compatible.
2. Add Else-If condition for RMII mode in the set of supported interfaces.
Support for RMII mode is already present in the driver and I had
missed out adding a condition for RMII mode in the previous patches.
v2 -> v3:
1. In ti,k3-am654-cpsw-nuss.yaml, restrict if/then statement to port
nodes.
v1 -> v2:
1. Add new compatible for CPSW5G in ti,k3-am654-cpsw-nuss.yaml and extend
properties for new compatible.
2. Add extra_modes member to struct am65_cpsw_pdata to be used for QSGMII
mode by new compatible.
3. Add check for phylink supported modes to ensure that only one phy mode
is advertised as supported.
4. Check if extra_modes supports QSGMII mode in am65_cpsw_nuss_mac_config()
for register write.
5. Add check for assigning port->sgmii_base only when extra_modes is valid.
net: ethernet: ti: am65-cpsw: Move phy_set_mode_ext() to correct location
In TI's J7200 SoC CPSW5G ports, each of the 4 ports can be configured
as a QSGMII main or QSGMII-SUB port. This configuration is performed
by phy-gmii-sel driver on invoking the phy_set_mode_ext() function.
It is necessary for the QSGMII main port to be configured before any of
the QSGMII-SUB interfaces are brought up. Currently, the QSGMII-SUB
interfaces come up before the QSGMII main port is configured.
Fix this by moving the call to phy_set_mode_ext() from
am65_cpsw_nuss_ndo_slave_open() to am65_cpsw_nuss_init_slave_ports(),
thereby ensuring that the QSGMII main port is configured before any of
the QSGMII-SUB ports are brought up.
dt-bindings: net: ti: k3-am654-cpsw-nuss: Update bindings for J7200 CPSW5G
Update bindings for TI K3 J7200 SoC which contains 5 ports (4 external
ports) CPSW5G module and add compatible for it.
Changes made:
- Add new compatible ti,j7200-cpswxg-nuss for CPSW5G.
- Extend pattern properties for new compatible.
- Change maximum number of CPSW ports to 4 for new compatible.
Yang Yingliang [Mon, 22 Aug 2022 02:53:46 +0000 (10:53 +0800)]
net: neigh: don't call kfree_skb() under spin_lock_irqsave()
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So add all skb to
a tmp list, then free them after spin_unlock_irqrestore() at
once.
Fixes: 66ba215cb513 ("neigh: fix possible DoS due to net iface start/stop loop") Suggested-by: Denis V. Lunev <[email protected]> Signed-off-by: Yang Yingliang <[email protected]> Reviewed-by: Nikolay Aleksandrov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Menglong Dong [Sun, 21 Aug 2022 05:18:58 +0000 (13:18 +0800)]
net: skb: prevent the split of kfree_skb_reason() by gcc
Sometimes, gcc will optimize the function by spliting it to two or
more functions. In this case, kfree_skb_reason() is splited to
kfree_skb_reason and kfree_skb_reason.part.0. However, the
function/tracepoint trace_kfree_skb() in it needs the return address
of kfree_skb_reason().
This split makes the call chains becomes:
kfree_skb_reason() -> kfree_skb_reason.part.0 -> trace_kfree_skb()
which makes the return address that passed to trace_kfree_skb() be
kfree_skb().
Therefore, introduce '__fix_address', which is the combination of
'__noclone' and 'noinline', and apply it to kfree_skb_reason() to
prevent to from being splited or made inline.
(Is it better to simply apply '__noclone oninline' to kfree_skb_reason?
I'm thinking maybe other functions have the same problems)
Meanwhile, wrap 'skb_unref()' with 'unlikely()', as the compiler thinks
it is likely return true and splits kfree_skb_reason().
Currently, net.netfilter.nf_conntrack_frag6_high_thresh can only be lowered.
I found this issue while investigating a probable kernel issue
causing flakes in tools/testing/selftests/net/ip_defrag.sh
In particular, these sysctl changes were ignored:
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000 >/dev/null 2>&1
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_low_thresh=7000000 >/dev/null 2>&1
This change is inline with commit 836196239298 ("net/ipfrag: let ip[6]frag_high_thresh
in ns be higher than in init_net")
Fixes: 8db3d41569bb ("netfilter: nf_defrag_ipv6: use net_generic infra") Signed-off-by: Eric Dumazet <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
netfilter: flowtable: fix stuck flows on cleanup due to pending work
To clear the flow table on flow table free, the following sequence
normally happens in order:
1) gc_step work is stopped to disable any further stats/del requests.
2) All flow table entries are set to teardown state.
3) Run gc_step which will queue HW del work for each flow table entry.
4) Waiting for the above del work to finish (flush).
5) Run gc_step again, deleting all entries from the flow table.
6) Flow table is freed.
But if a flow table entry already has pending HW stats or HW add work
step 3 will not queue HW del work (it will be skipped), step 4 will wait
for the pending add/stats to finish, and step 5 will queue HW del work
which might execute after freeing of the flow table.
To fix the above, this patch flushes the pending work, then it sets the
teardown flag to all flows in the flowtable and it forces a garbage
collector run to queue work to remove the flows from hardware, then it
flushes this new pending work and (finally) it forces another garbage
collector run to remove the entry from the software flowtable.
Linus Torvalds [Wed, 24 Aug 2022 02:33:28 +0000 (19:33 -0700)]
Merge tag 'cgroup-for-6.0-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- The psi data structure was changed to be allocated dynamically but
it wasn't being cleared leading to it reporting garbage values and
triggering spurious oom kills.
- A deadlock involving cpuset and cpu hotplug.
- When a controller is moved across cgroup hierarchies,
css->rstat_css_node didn't get RCU drained properly from the previous
list.
* tag 'cgroup-for-6.0-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Fix race condition at rebind_subsystems()
cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock
sched/psi: Remove redundant cgroup_psi() when !CONFIG_CGROUPS
sched/psi: Remove unused parameter nbytes of psi_trigger_create()
sched/psi: Zero the memory of struct psi_group
Linus Torvalds [Wed, 24 Aug 2022 02:26:48 +0000 (19:26 -0700)]
Merge tag 'audit-pr-20220823' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A single fix for a potential double-free on a fsnotify error path"
* tag 'audit-pr-20220823' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix potential double free on error path from fsnotify_add_inode_mark
Linus Torvalds [Wed, 24 Aug 2022 02:17:26 +0000 (19:17 -0700)]
Merge tag 'fs.fixes.v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping
Pull file_remove_privs() fix from Christian Brauner:
"As part of Stefan's and Jens' work to add async buffered write
support to xfs we refactored file_remove_privs() and added
__file_remove_privs() to avoid calling __remove_privs() when
IOCB_NOWAIT is passed.
While debugging a recent performance regression report I found that
during review we missed that commit faf99b563558 ("fs: add
__remove_file_privs() with flags parameter") accidently changed
behavior when dentry_needs_remove_privs() returns zero.
Before the commit it would still call inode_has_no_xattr() setting
the S_NOSEC bit and thereby avoiding even calling into
dentry_needs_remove_privs() the next time this function is called.
After that commit inode_has_no_xattr() would only be called if
__remove_privs() had to be called.
Restore the old behavior. This is likely the cause of the performance
regression"
* tag 'fs.fixes.v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
fs: __file_remove_privs(): restore call to inode_has_no_xattr()
Jakub Kicinski [Wed, 24 Aug 2022 00:50:26 +0000 (17:50 -0700)]
Merge tag 'mlx5-fixes-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-08-22
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Unlock on error in mlx5_sriov_enable()
net/mlx5e: Fix use after free in mlx5e_fs_init()
net/mlx5e: kTLS, Use _safe() iterator in mlx5e_tls_priv_tx_list_cleanup()
net/mlx5: unlock on error path in esw_vfs_changed_event_handler()
net/mlx5e: Fix wrong tc flag used when set hw-tc-offload off
net/mlx5e: TC, Add missing policer validation
net/mlx5e: Fix wrong application of the LRO state
net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
net/mlx5: Fix cmd error logging for manage pages cmd
net/mlx5: Disable irq when locking lag_lock
net/mlx5: Eswitch, Fix forwarding decision to uplink
net/mlx5: LAG, fix logic over MLX5_LAG_FLAG_NDEVS_READY
net/mlx5e: Properly disable vlan strip on non-UL reps
====================
this small series is supposed to fix the issues around AF_XDP usage with
reduced queue count on interface. Due to the XDP rings setup, some
configurations can result in sockets not seeing traffic flowing. More
about this in description of patch 2.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: xsk: use Rx ring's XDP ring when picking NAPI context
ice: xsk: prohibit usage of non-balanced queue id
====================
The patches add the below feature support for both TJA1100 and
TJA1101 PHYs cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.
====================
TJA110x REF_CLK can be configured as interface reference clock
intput or output when the RMII mode enabled. This patch add the
property to make the REF_CLK can be configurable.
====================
mlxsw: Introduce modular system support by minimal driver
Vadim Pasternak writes:
This patchset adds line cards support in mlxsw_minimal, which is used
for monitoring purposes on BMC systems. The BMC is connected to the
ASIC over I2C bus, unlike the host CPU that is connected to the ASIC
via PCI bus.
The BMC system needs to be notified whenever line cards become active
or inactive, so that, for example, netdevs will be registered /
unregistered by mlxsw_minimal. However, traps cannot be generated
towards the BMC over the I2C bus. To overcome that, the I2C bus driver
(i.e., mlxsw_i2c) registers an handler for an IRQ that is fired upon
specific system wide changes, like line card activation and
deactivation.
The generated event is handled by mlxsw_core, which checks whether
anything changed in the state of available line cards. If a line card
becomes active or inactive, interested parties such as mlxsw_minimal
are notified via their registered line card event callback.
Patch set overview:
Patches #1 is preparations.
Patches #2-#3 extend mlxsw_core with an infrastructure to handle the
previously mentioned system events.
Patch #4 extends the I2C bus driver to register an handler for the IRQ
fired upon specific system wide changes.
Patches #5-#8 gradually add line cards support in mlxsw_minimal by
dynamically registering / unregistering netdevs for ports found on
line cards, whenever a line card becomes active / inactive.
====================
projects / linux.git / log