Linus Torvalds [Sun, 8 Jan 2017 19:22:00 +0000 (11:22 -0800)]
Merge tag 'staging-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some staging and IIO driver fixes for 4.10-rc3.
Most of these are minor IIO fixes of reported issues, along with one
network driver fix to resolve an issue. And a MAINTAINERS update with
a new mailing list. All of these, except the MAINTAINERS file update,
have been in linux-next with no reported issues (the MAINTAINERS patch
happened on Friday...)"
* tag 'staging-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
MAINTAINERS: add greybus subsystem mailing list
staging: octeon: Call SET_NETDEV_DEV()
iio: accel: st_accel: fix LIS3LV02 reading and scaling
iio: common: st_sensors: fix channel data parsing
iio: max44000: correct value in illuminance_integration_time_available
iio: adc: TI_AM335X_ADC should depend on HAS_DMA
iio: bmi160: Fix time needed to sleep after command execution
iio: 104-quad-8: Fix active level mismatch for the preset enable option
iio: 104-quad-8: Fix off-by-one errors when addressing IOR
iio: 104-quad-8: Fix index control configuration
Jacob Keller [Fri, 18 Nov 2016 17:45:39 +0000 (09:45 -0800)]
fm10k: remove FM10K_FLAG_DEBUG_STATS
The debug statistics were removed due to complications with the ethtool
statistics API which are not possible to resolve without a new
statistics interface. The flag was left behind, but we no longer need
it.
Jacob Keller [Fri, 18 Nov 2016 17:45:38 +0000 (09:45 -0800)]
fm10k: report the receive timestamp in FM10K_CB(skb)->tstamp
This was accidentally removed when we defeatured the full 1588 Clock
support. We need to report the Rx descriptor timestamp value so that
applications built on top of the IES API can function properly.
Additionally, remove the FM10K_FLAG_RX_TS_ENABLED, as it is not used now
that 1588 functionality has been removed.
Scott Peterson [Thu, 3 Nov 2016 23:09:41 +0000 (16:09 -0700)]
fm10k: Limit dma sync of RX buffers to actual packet size
On packet RX, we perform a dma sync for cpu before passing the
packet up. Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.
Ngai-Mint Kwan [Wed, 2 Nov 2016 23:44:47 +0000 (16:44 -0700)]
fm10k: do not clear global mailbox interrupt bits
Partially revert commit 5e93cbadd3e9 ("fm10k: Reset mailbox global
interrupts", 2016-06-07)
The register bits related to this commit are now solely being handled by
the IES API. Recent changes in the IES API will allow an automatic
recovery from improper handling of these bits.
Ngai-Mint Kwan [Wed, 2 Nov 2016 23:44:46 +0000 (16:44 -0700)]
fm10k: request reset when mbx->state changes
Multiple IES API resets can cause a race condition where the mailbox
interrupt request bits can be cleared before being handled. This can
leave certain mailbox messages from the PF to be untreated and the PF
will enter in some inactive state. If this situation occurs, the IES API
will initiate a mailbox version reset which, then, trigger a mailbox
state change. Once this mailbox transition occurs (from OPEN to CONNECT
state), a request for reset will be returned.
This ensures that PF will undergo a reset whenever IES API encounters an
unknown global mailbox interrupt event or whenever the IES API
terminates.
Michael Chan [Fri, 6 Jan 2017 21:18:53 +0000 (16:18 -0500)]
tg3: Fix race condition in tg3_get_stats64().
The driver's ndo_get_stats64() method is not always called under RTNL.
So it can race with driver close or ethtool reconfigurations. Fix the
race condition by taking tp->lock spinlock in tg3_free_consistent()
when freeing the tp->hw_stats memory block. tg3_get_stats64() is
already taking tp->lock.
Ivan Vecera [Fri, 6 Jan 2017 20:59:30 +0000 (21:59 +0100)]
be2net: fix unicast list filling
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Johannes Weiner [Sat, 7 Jan 2017 00:21:43 +0000 (19:21 -0500)]
mm: workingset: fix use-after-free in shadow node shrinker
Several people report seeing warnings about inconsistent radix tree
nodes followed by crashes in the workingset code, which all looked like
use-after-free access from the shadow node shrinker.
Dave Jones managed to reproduce the issue with a debug patch applied,
which confirmed that the radix tree shrinking indeed frees shadow nodes
while they are still linked to the shadow LRU:
This is the WARN_ON_ONCE(!list_empty(&node->private_list)) placed in the
inlined radix_tree_shrink().
The problem is with 14b468791fa9 ("mm: workingset: move shadow entry
tracking to radix tree exceptional tracking"), which passes an update
callback into the radix tree to link and unlink shadow leaf nodes when
tree entries change, but forgot to pass the callback when reclaiming a
shadow node.
While the reclaimed shadow node itself is unlinked by the shrinker, its
deletion from the tree can cause the left-most leaf node in the tree to
be shrunk. If that happens to be a shadow node as well, we don't unlink
it from the LRU as we should.
Consider this tree, where the s are shadow entries:
root->rnode
|
[0 n]
| |
[s ] [sssss]
Now the shadow node shrinker reclaims the rightmost leaf node through
the shadow node LRU:
root->rnode
|
[0 ]
|
[s ]
Because the parent of the deleted node is the first level below the
root and has only one child in the left-most slot, the intermediate
level is shrunk and the node containing the single shadow is put in
its place:
root->rnode
|
[s ]
The shrinker again sees a single left-most slot in a first level node
and thus decides to store the shadow in root->rnode directly and free
the node - which is a leaf node on the shadow node LRU.
root->rnode
|
s
Without the update callback, the freed node remains on the shadow LRU,
where it causes later shrinker runs to crash.
Pass the node updater callback into __radix_tree_delete_node() in case
the deletion causes the left-most branch in the tree to collapse too.
Also add warnings when linked nodes are freed right away, rather than
wait for the use-after-free when the list is scanned much later.
David S. Miller [Sun, 8 Jan 2017 02:03:51 +0000 (21:03 -0500)]
Merge branch 'netcp-next'
Murali Karicheri says:
====================
netcp: enhancements and minor fixes
This series is for net-next. This propagates enhancements and minor
bug fixes from internal version of the driver to keep the upstream
in sync. Please review and apply if this looks good.
Tested on all of K2HK/E/L boards with nfs rootfs.
Test logs below
K2HK-EVM: http://pastebin.ubuntu.com/23754106/
k2L-EVM: http://pastebin.ubuntu.com/23754143/
K2E-EVM: http://pastebin.ubuntu.com/23754159/
History:
v1 - dropped 1/10 amd 2/10 of v0 based on comments from Rob as
it needs more work before submission
v0 - Initial version
====================
net: netcp: ale: add proper ale entry mask bits for netcp switch ALE
For NetCP NU Switch ALE, some of the mask bits are different than
defaults used in the driver. Add a new macro DEFINE_ALE_FIELD1 that use
a configurable mask bits and use it in the driver. These bits are set to
correct values by using the new variables added to cpsw_ale structure
and re-used in the macros. The parameter nu_switch_ale is configured by
the caller driver to indicate the ALE is for that switch and is used in
the ALE driver to do customization as needed.
net: netcp: ale: use ale_status to size the ale table
ALE h/w on newer version of NetCP (K2E/L/G) does provide a ALE_STATUS
register for the size of the ALE Table implemented in h/w. Currently
for example we set ALE Table size to 1024 for NetCP ALE on
K2E even though the ALE Status/Documentation shows it has 8192 entries.
So take advantage of this register to read the size of ALE table supported
and use that value in the driver for the newer version of NetCP ALE.
For NetCP lite, ALE Table size is much less (64) and indicated by a size
of zero in ALE_STATUS. So use that as a default for now. While at it,
also fix the ale table size on 10G switch to 2048 per User guide
http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
net: netcp: ale: update to support unknown vlan controls for NU switch
In NU Ethernet switch used on some of the Keystone SoCs, there is
separate UNKNOWNVLAN register for membership, unreg mcast flood, reg
mcast flood and force untag egress bits in ALE. So control for these
fields require different address offset, shift and size of field.
As this ALE has the same version number as ALE in CPSW found on other
SoCs, customization based on version number is not possible. So
use a configuration parameter, nu_switch_ale, to identify the ALE
ALE found in NU Switch. Different treatment is needed for NU Switch
ALE due to difference in the ale table bits, separate unknown vlan
registers etc. The register information available in ale_controls,
needs to be updated to support the netcp NU switch h/w. So it is not
constant array any more since it needs to be updated based
on ALE type. The header of the file is also updated to indicate it
supports N port switch ALE, not just 3 port. The version mask is
3 bits in NU Switch ALE vs 8 bits on other ALE types.
While at it, change the debug print to info print so that ALE
version gets displayed in boot log.
net: netcp: use hw capability to remove FCS word from rx packets
Some of the newer Ethernet switch hw (such as that on k2e/l/g) can
strip the Etherenet FCS from packet at the port 0 egress of the switch.
So use this capability instead of doing it in software.
net: netcp: ethss: get phy-handle only if link interface is MAC-to-PHY
Currently to parse phy-handle, driver doesn't check if the interface is
MAC to PHY. This patch add this check for all MAC to PHY interface types
supported by the driver.
Previously the network statistics were stored in 32 bit variable
which can cause some stats to roll over after several minutes of
high traffic. This implements 64 bit storage so larger numbers
can be stored.
The psdata is populated with command data by netcp modules
to the tail of the buffer and set_words() copy the same
to the front of the psdata. So remove the redundant memmov
function call.
net: netcp: extract eflag from desc for rx_hook handling
Extract the eflag bits from the received desc and pass it down
the rx_hook chain to be available for netcp modules. Also the
psdata and epib data has to be inspected by the netcp modules.
So the desc can be freed only after returning from the rx_hook.
So move knav_pool_desc_put() after the rx_hook processing.
Hugh Dickins [Sat, 7 Jan 2017 23:37:31 +0000 (15:37 -0800)]
mm: stop leaking PageTables
4.10-rc loadtest (even on x86, and even without THPCache) fails with
"fork: Cannot allocate memory" or some such; and /proc/meminfo shows
PageTables growing.
Commit 953c66c2b22a ("mm: THP page cache support for ppc64") that got
merged in rc1 removed the freeing of an unused preallocated pagetable
after do_fault_around() has called map_pages().
This is usually a good optimization, so that the followup doesn't have
to reallocate one; but it's not sufficient to shift the freeing into
alloc_set_pte(), since there are failure cases (most commonly
VM_FAULT_RETRY) which never reach finish_fault().
Check and free it at the outer level in do_fault(), then we don't need
to worry in alloc_set_pte(), and can restore that to how it was (I
cannot find any reason to pte_free() under lock as it was doing).
And fix a separate pagetable leak, or crash, introduced by the same
change, that could only show up on some ppc64: why does do_set_pmd()'s
failure case attempt to withdraw a pagetable when it never deposited
one, at the same time overwriting (so leaking) the vmf->prealloc_pte?
Residue of an earlier implementation, perhaps? Delete it.
David S. Miller [Sun, 8 Jan 2017 01:48:16 +0000 (20:48 -0500)]
Merge branch 'cpsw-cpdma-DDR'
Grygorii Strashko says:
====================
net: ethernet: ti: cpsw: support placing CPDMA descriptors into DDR
This series intended to add support for placing CPDMA descriptors into
DDR by introducing new module parameter "descs_pool_size" to specify
size of descriptor's pool. The "descs_pool_size" defines total number
of CPDMA CPPI descriptors to be used for both ingress/egress packets
processing. If not specified - the default value 256 will be used
which will allow to place descriptor's pool into the internal CPPI
RAM.
In addition, added ability to re-split CPDMA pool of descriptors
between RX and TX path via ethtool '-G' command wich will allow to
configure and fix number of descriptors used by RX and TX path, which,
then, will be split between RX/TX channels proportionally depending on
number of RX/TX channels and its weight.
This allows significantly to reduce UDP packets drop rate for
bandwidth >301 Mbits/sec (am57x).
Before enabling this feature, the am437x SoC has to be fixed as it's
proved that it's not working when CPDMA descriptors placed in DDR.
So, the patch 1 fixes this issue.
====================
Even if no_bd_ram property is described in TI CPSW bindings the support for
it has never been introduced in CPSW driver, so there are no real users of
it. Hence, remove no_bd_ram property from documentation and DT files.
net: ethernet: ti: cpsw: add support for ringparam configuration
The CPDMA uses one pool of descriptors for both RX and TX which by default
split between all channels proportionally depending on total number of
CPDMA channels and number of TX and RX channels. As result, more
descriptors will be consumed by TX path if there are more TX channels and
there is no way now to dedicate more descriptors for RX path.
So, add the ability to re-split CPDMA pool of descriptors between RX and TX
path via ethtool '-G' command wich will allow to configure and fix number
of descriptors used by RX and TX path, which, then, will be split between
RX/TX channels proportionally depending on RX/TX channels number and
weight. ethtool '-G' command will accept only number of RX entries and rest
of descriptors will be arranged for TX automatically.
Command:
ethtool -G <devname> rx <number of descriptors>
defaults and limitations:
- minimum number of rx descriptors is 10% of total number of descriptors in
CPDMA pool
- maximum number of rx descriptors is 90% of total number of descriptors in
CPDMA pool
- by default, descriptors will be split equally between RX/TX path
- any values passed in "tx" parameter will be ignored
net: ethernet: ti: cpsw: add support for descs pool size configuration
The CPSW CPDMA can process buffer descriptors placed as in internal
CPPI RAM as in DDR. This patch adds support in CPSW and CPDMA for
descs_pool_size mudule parameter, which defines total number of CPDMA CPPI
descriptors to be used for both ingress/egress packets processing:
- memory size, required for CPDMA descriptor pool, is calculated basing
on number of descriptors specified by user in descs_pool_size and
CPDMA descriptor size and allocated from coherent memory (CMA area);
- CPDMA descriptor pool will be allocated in DDR if pool memory size >
internal CPPI RAM or use internal CPPI RAM otherwise;
- if descs_pool_size not specified in DT - the default value 256 will
be used which will allow to place CPDMA descriptors pool into the
internal CPPI RAM (current default behaviour);
- CPDMA will ignore descs_pool_size if descs_pool_size = 0 for
backward comaptiobility with davinci_emac.
descs_pool_size is boot time setting and can't be changed once
CPSW/CPDMA is initialized.
net: ethernet: ti: cpdma: minimize number of parameters in cpdma_desc_pool_create/destroy()
Update cpdma_desc_pool_create/destroy() to accept only one parameter
struct cpdma_ctlr*, as this structure contains all required
information for pool creation/destruction.
The currently processing cpdma descriptor with EOQ flag set may
contain two values in Next Descriptor Pointer field:
- valid pointer: means CPDMA missed addition of new desc in queue;
- null: no more descriptors in queue.
In the later case, it's not required to write to HDP register, but now
CPDMA does it.
Hence, add additional check for Next Descriptor Pointer != null in
cpdma_chan_process() function before writing in HDP register.
net: ethernet: ti: cpdma: am437x: allow descs to be plased in ddr
It's observed that cpsw/cpdma is not working properly when CPPI
descriptors are placed in DDR instead of internal CPPI RAM on am437x
SoC:
- rx/tx silently stops processing packets;
- or - after boot it's working for sometime, but stuck once Network
load is increased (ping is working, but iperf is not).
(The same issue has not been reproduced on am335x and am57xx).
It seems that write to HDP register processed faster by interconnect
than writing of descriptor memory buffer in DDR, which is probably
caused by store buffer / write buffer differences as these functions
are implemented differently across devices. So, to fix this i come up
with two minimal, required changes:
1) all accesses to the channel register HDP/CP/RXFREE registers should
be done using sync IO accessors readl()/writel(), because all previous
memory writes writes have to be completed before starting channel
(write to HDP) or completing desc processing.
2) the change 1 only doesn't work on am437x and additional reading of
desc's field is required right after the new descriptor was filled
with data and before pointer on it will be stored in
prev_desc->hw_next field or HDP register.
In addition, to above changes this patch eliminates all relaxed ordering
I/O accessors in this driver as suggested by David Miller to avoid such
kind of issues in the future, but with one exception - relaxed IO accessors
will still be used to fill desc in cpdma_chan_submit(), which is safe as
there is read barrier at the end of write sequence, and because sync IO
accessors usage here will affect on net performance.
Linus Torvalds [Sat, 7 Jan 2017 17:47:43 +0000 (09:47 -0800)]
Merge branch 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"The asm-prototypes.h file added in the last merge window results in
invalid code with CONFIG_KMEMCHECK=y. The net result is that genksyms
segfaults.
This pull request fixes the header, the genksyms fix is in my kbuild
branch for 4.11"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
asm-prototypes: Clear any CPP defines before declaring the functions
Ivan Vecera [Fri, 6 Jan 2017 19:30:02 +0000 (20:30 +0100)]
be2net: fix accesses to unicast list
Commit 988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
David S. Miller [Sat, 7 Jan 2017 03:18:57 +0000 (22:18 -0500)]
Merge branch 'l2tp-cleanup-socket-lookup-code'
Guillaume Nault says:
====================
l2tp: cleanup socket lookup code in l2tp_ip and l2tp_ip6
First three patches remove redundant tests and add missing "const"
qualifiers.
Fourth patch splits the conditionals found in __l2tp_ip*_bind_lookup(),
to make these functions easier to review. In the process, I found that
some corner cases were still not handled properly. So I've added the
missing tests in this patch too, because they're pretty simple and the
whole "if" statements are modified anyway.
I expect it to be easier to review this way. If not, I can split up
patch #4, post the missing tests separately to -net, and later repost
this series as pure cleanup. Just let me know.
====================
Guillaume Nault [Fri, 6 Jan 2017 19:03:57 +0000 (20:03 +0100)]
l2tp: rework socket comparison in __l2tp_ip*_bind_lookup()
Split conditions, so that each test becomes clearer.
Also, for l2tp_ip, check if "laddr" is 0. This prevents a socket from
binding to the unspecified address when other sockets are already bound
using the same device (if any), connection ID and namespace.
Same thing for l2tp_ip6: add ipv6_addr_any(laddr) and
ipv6_addr_any(raddr) tests to ensure that an IPv6 unspecified address
passed as parameter is properly treated a wildcard.
Xin Long [Fri, 6 Jan 2017 14:18:33 +0000 (22:18 +0800)]
sctp: prepare asoc stream for stream reconf
sctp stream reconf, described in RFC 6525, needs a structure to
save per stream information in assoc, like stream state.
In the future, sctp stream scheduler also needs it to save some
stream scheduler params and queues.
This patchset is to prepare the stream array in assoc for stream
reconf. It defines sctp_stream that includes stream arrays inside
to replace ssnmap.
Note that we use different structures for IN and OUT streams, as
the members in per OUT stream will get more and more different
from per IN stream.
v1->v2:
- put these patches into a smaller group.
v2->v3:
- define sctp_stream to contain stream arrays, and create stream.c
to put stream-related functions.
- merge 3 patches into 1, as new sctp_stream has the same name
with before.
Eric Garver [Fri, 6 Jan 2017 01:22:36 +0000 (20:22 -0500)]
udp: inuse checks can quit early for reuseport
UDP lib inuse checks will walk the entire hash bucket to check if the
portaddr is in use. In the case of reuseport we can stop searching when
we find a matching reuseport.
On a 16-core VM a test program that spawns 16 threads that each bind to
1024 sockets (one per 10ms) takes 1m45s. With this change it takes 11s.
Also add a cond_resched() when the port is not specified.
Linus Torvalds [Fri, 6 Jan 2017 23:38:39 +0000 (15:38 -0800)]
Merge tag 'sound-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing particular stands out, only a few small fixes for USB-audio,
HD-audio and Firewire. The USB-audio fix is the respin of the previous
race fix after a revert due to the regression"
* tag 'sound-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
Revert "ALSA: firewire-lib: change structure member with proper type"
ALSA: usb-audio: test EP_FLAG_RUNNING at urb completion
ALSA: usb-audio: Fix irq/process data synchronization
ALSA: hda - Apply asus-mode8 fixup to ASUS X71SL
ALSA: hda - Fix up GPIO for ASUS ROG Ranger
ALSA: firewire-lib: change structure member with proper type
ALSA: firewire-tascam: Fix to handle error from initialization of stream data
ALSA: fireworks: fix asymmetric API call at unit removal
Linus Torvalds [Fri, 6 Jan 2017 23:35:27 +0000 (15:35 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One fix for a broken driver on Renesas RZ/A1 SoCs with bootloaders
that don't turn all the clks on and another fix for stm32f4 SoCs where
we have multiple drivers attaching to the same DT node"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
David S. Miller [Fri, 6 Jan 2017 21:26:19 +0000 (16:26 -0500)]
Merge tag 'mac80211-for-davem-2017-01-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another single fix, to correctly handle destruction of a
single netlink socket having ownership of multiple objects
(scheduled scan requests and interfaces.)
====================
David Forster [Fri, 6 Jan 2017 10:27:59 +0000 (10:27 +0000)]
vti6: fix device register to report IFLA_INFO_KIND
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
David S. Miller [Fri, 6 Jan 2017 21:05:37 +0000 (16:05 -0500)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-01-06
This series contains updates/fixes to igb and e1000e.
Joe fixes indentation and improper line wrapping in igb.
David Singleton fixes an issue in e1000e where in systemd, where things
are done in parallel and can create a condition where e1000_shutdown is
called after e1000_close, hitting BUG_ON assert in free_msi_irqs.
Cao Jin fixes a code comment on the wakeup status register. Also fixes
a possible NULL pointer dereference by using igb_adapter->io_addr
instead of e1000_hw->hw_addr in igb_configure_tx_ring().
Chris Arges works around a firmware issue, which can cause probe of i210
NIC to fail, so zero the page select register during igb_get_phy_id() to
workaround the issue. Aaron Sierra adds also a check for this issue
during the initialization of PHY parameters to ensure that this same
issue happens after probe.
Todd fixes a possible race condition in close/suspend by extending
the rtnl_lock() to protect the call to netif_device_detach() and
igb_clear_interrupt_scheme(). Also adds i211 to a known i210/i211
workaround.
Hannu Lounento fixes inverted logic on a debug statement.
====================
David Ahern [Fri, 6 Jan 2017 03:32:46 +0000 (19:32 -0800)]
net: ipv4: Simplify rt_fill_info
rt_fill_info has only 1 caller and both of the last 2 args -- nowait
and flags -- are hardcoded to 0. Given that remove them as input arguments
and simplify rt_fill_info accordingly.
The issue comes when there are multiple threads attempting to use
the mailbox facility at the same time.
When DCB operations and interface up/down is run in a loop for every
0.1 sec, we observed mailbox collisions. And out of the two commands
one would fail with the present code, since we don't queue the second
command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at
the head issue the mailbox command, else wait for the existing command
to complete. Usually command takes less than a milli-second to
complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be
very rare since no one runs such abusive script.
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Weilin Chang [Thu, 5 Jan 2017 00:18:50 +0000 (16:18 -0800)]
liquidio: fix wrong information about channels reported to ethtool
Information reported to ethtool about channels is sometimes wrong for PF,
and always wrong for VF. Fix them by getting the information from the
right fields from the right structs.
Mahesh Bandewar [Wed, 4 Jan 2017 23:01:01 +0000 (15:01 -0800)]
ipv6: do not send RTM_DELADDR for tentative addresses
RTM_NEWADDR notification is sent when IFA_F_TENTATIVE is cleared from
the address. So if the address is added and deleted before DAD probes
completes, the RTM_DELADDR will be sent for which there was no
RTM_NEWADDR causing asymmetry in notification. However if the same
logic is used while sending RTM_DELADDR notification, this asymmetry
can be avoided.
amd-xgbe: Fix IRQ processing when running in single IRQ mode
When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
The VF driver is using the wrong struct when sending commands to the NIC
firmware, sometimes causing adverse effects in the firmware. The right
struct is the one that the PF is using, so make the VF use that as well.
Sergei Shtylyov [Wed, 4 Jan 2017 21:29:32 +0000 (00:29 +0300)]
sh_eth: R8A7740 supports packet shecksumming
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740") Signed-off-by: Sergei Shtylyov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Sergei Shtylyov [Wed, 4 Jan 2017 19:18:24 +0000 (22:18 +0300)]
sh_eth: fix EESIPR values for SH77{34|63}
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes: 380af9e390ec ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"") Fixes: f5d12767c8fd ("sh_eth: get SH77{34|63} support out of #ifdef") Signed-off-by: Sergei Shtylyov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Fri, 6 Jan 2017 19:19:03 +0000 (11:19 -0800)]
Merge tag 'vfio-v4.10-rc3' of git://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Add mtty sample driver properly into build system (Alex Williamson)
- Restore type1 mapping performance after mdev (Alex Williamson)
- Fix mdev device race (Alex Williamson)
- Cleanups to the mdev ABI used by vendor drivers (Alex Williamson)
- Build fix for old compilers (Arnd Bergmann)
- Fix sample driver error path (Dan Carpenter)
- Handle pci_iomap() error (Arvind Yadav)
- Fix mdev ioctl return type (Paul Gortmaker)
* tag 'vfio-v4.10-rc3' of git://github.com/awilliam/linux-vfio:
vfio-mdev: fix non-standard ioctl return val causing i386 build fail
vfio-pci: Handle error from pci_iomap
vfio-mdev: fix some error codes in the sample code
vfio-pci: use 32-bit comparisons for register address for gcc-4.5
vfio-mdev: Make mdev_device private and abstract interfaces
vfio-mdev: Make mdev_parent private
vfio-mdev: de-polute the namespace, rename parent_device & parent_ops
vfio-mdev: Fix remove race
vfio/type1: Restore mapping performance with mdev support
vfio-mdev: Fix mtty sample driver building
Linus Torvalds [Fri, 6 Jan 2017 18:53:21 +0000 (10:53 -0800)]
Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb fixes from Konrad Rzeszutek Wilk:
"This has one fix to make i915 work when using Xen SWIOTLB, and a
feature from Geert to aid in debugging of devices that can't do DMA
outside the 32-bit address space.
The feature from Geert is on top of v4.10 merge window commit
(specifically you pulling my previous branch), as his changes were
dependent on the Documentation/ movement patches.
I figured it would just easier than me trying than to cherry-pick the
Documentation patches to satisfy git.
The patches have been soaking since 12/20, albeit I updated the last
patch due to linux-next catching an compiler error and adding an
Tested-and-Reported-by tag"
* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Export swiotlb_max_segment to users
swiotlb: Add swiotlb=noforce debug option
swiotlb: Convert swiotlb_force from int to enum
x86, swiotlb: Simplify pci_swiotlb_detect_override()
Linus Torvalds [Fri, 6 Jan 2017 18:49:36 +0000 (10:49 -0800)]
Merge tag 'iommu-fixes-v4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Three fixes queued up:
- fix an issue with command buffer overflow handling in the AMD IOMMU
driver
- add an additional context entry flush to the Intel VT-d driver to
make sure any old context entry from kdump copying is flushed out
of the cache
- correct the encoding of the PASID table size in the Intel VT-d
driver"
* tag 'iommu-fixes-v4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix the left value check of cmd buffer
iommu/vt-d: Fix pasid table size encoding
iommu/vt-d: Flush old iommu caches for kdump when the device gets context mapped
Linus Torvalds [Fri, 6 Jan 2017 18:40:17 +0000 (10:40 -0800)]
Merge tag 'acpi-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a device enumeration problem related to _ADR matching and an
IOMMU initialization issue related to the DMAR table missing, remove
an excessive function call from the core ACPI code, update an error
message in the ACPI WDAT watchdog driver and add a way to work around
problems with unhandled GPE notifications.
Specifics:
- Fix a device enumeration issue leading to incorrect associations
between ACPI device objects and platform device objects
representing physical devices if the given device object has both
_ADR and _HID (Rafael Wysocki).
- Avoid passing NULL to acpi_put_table() during IOMMU initialization
which triggers a (rightful) warning from ACPICA (Rafael Wysocki).
- Drop an excessive call to acpi_dma_deconfigure() from the core code
that binds ACPI device objects to device objects representing
physical devices (Lorenzo Pieralisi).
- Update an error message in the ACPI WDAT watchdog driver to make it
provide more useful information (Mika Westerberg).
- Add a mechanism to work around issues with unhandled GPE
notifications that occur during system initialization and cannot be
prevented by means of sysfs (Lv Zheng)"
* tag 'acpi-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / DMAR: Avoid passing NULL to acpi_put_table()
ACPI / scan: Prefer devices without _HID/_CID for _ADR matching
ACPI / watchdog: Print out error number when device creation fails
ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding
ACPI: Drop misplaced acpi_dma_deconfigure() call from acpi_bind_one()
Linus Torvalds [Fri, 6 Jan 2017 18:37:50 +0000 (10:37 -0800)]
Merge tag 'pm-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a few issues in the intel_pstate driver, a documetation
issue, a false-positive compiler warning in the generic power domains
framework and two problems in the devfreq subsystem. They also update
the MAINTAINERS entry for devfreq and add a new "compatible" string to
the generic cpufreq-dt driver.
Specifics:
- Fix a few intel_pstate driver issues: add missing locking it two
places, avoid exposing a useless debugfs interface and keep the
attribute values in sysfs in sync (Rafael Wysocki).
- Drop confusing kernel-doc references related to power management
and ACPI from the driver API manual (Rafael Wysocki).
- Make a false-positive compiler warning in the generic power domains
framework go away (Augusto Mecking Caringi).
- Fix two initialization issues in the devfreq subsystem and update
the MAINTAINERS entry for it (Chanwoo Choi).
- Add a new "compatible" string for APM X-Gene 2 to the generic DT
cpufreq driver (Hoan Tran)"
* tag 'pm-4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: dt: Add support for APM X-Gene 2
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
PM / domains: Fix 'may be used uninitialized' build warning
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
So they can figure out what is the optimal number of pages
that can be contingously stitched together without fear of
bounce buffer.
We also expose an mechanism for sub-users of SWIOTLB API, such
as Xen-SWIOTLB to set the max segment value. And lastly
if swiotlb=force is set (which mandates we bounce buffer everything)
we set max_segment so at least we can bounce buffer one 4K page
instead of a giant 512KB one for which we may not have space.
Merge branches 'pm-domains', 'pm-docs' and 'pm-devfreq'
* pm-domains:
PM / domains: Fix 'may be used uninitialized' build warning
* pm-docs:
PM / docs: Drop confusing kernel-doc references from infrastructure.rst
* pm-devfreq:
PM / devfreq: exynos-bus: Fix the wrong return value
PM / devfreq: Fix the bug of devfreq_add_device when governor is NULL
MAINTAINERS: Add myself as reviewer for DEVFREQ subsystem support
* pm-cpufreq:
cpufreq: dt: Add support for APM X-Gene 2
cpufreq: intel_pstate: Always keep all limits settings in sync
cpufreq: intel_pstate: Use locking in intel_cpufreq_verify_policy()
cpufreq: intel_pstate: Use locking in intel_pstate_resume()
cpufreq: intel_pstate: Do not expose PID parameters in passive mode
Todd Fujinaka [Tue, 15 Nov 2016 16:54:26 +0000 (08:54 -0800)]
igb: close/suspend race in netif_device_detach
Similar to ixgbe, when an interface is part of a namespace it is
possible that igb_close() may be called while __igb_shutdown() is
running which ends up in a double free WARN and/or a BUG in
free_msi_irqs().
Extend the rtnl_lock() to protect the call to netif_device_detach() and
igb_clear_interrupt_scheme() in __igb_shutdown() and check for
netif_device_present() to avoid calling igb_clear_interrupt_scheme() a
second time in igb_close().
Also extend the rtnl lock in igb_resume() to netif_device_attach().
igb: re-assign hw address pointer on reset after PCI error
Whenever the igb driver detects the result of a read operation returns
a value composed only by F's (like 0xFFFFFFFF), it will detach the
net_device, clear the hw_addr pointer and warn to the user that adapter's
link is lost - those steps happen on igb_rd32().
In case a PCI error happens on Power architecture, there's a recovery
mechanism called EEH, that will reset the PCI slot and call driver's
handlers to reset the adapter and network functionality as well.
We observed that once hw_addr is NULL after the error is detected on
igb_rd32(), it's never assigned back, so in the process of resetting
the network functionality we got a NULL pointer dereference in both
igb_configure_tx_ring() and igb_configure_rx_ring(). In order to avoid
such bug, this patch re-assigns the hw_addr value in the slot_reset
handler.
Aaron Sierra [Tue, 29 Nov 2016 16:03:56 +0000 (10:03 -0600)]
igb: reset the PHY before reading the PHY ID
Several people have reported firmware leaving the I210/I211 PHY's page
select register set to something other than the default of zero. This
causes the first accesses, PHY_IDx register reads, to access something
else, resulting in device probe failure:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
This problem began for them after a previous patch I submitted was
applied:
I personally experienced this problem after attempting to PXE boot from
I210 devices using this firmware:
Intel(R) Boot Agent GE v1.5.78
Copyright (C) 1997-2014, Intel Corporation
Resetting the PHY before reading from it, ensures the page select
register is in its default state and doesn't make assumptions about
the PHY's register set before the PHY has been probed.
Cao jin [Tue, 8 Nov 2016 07:06:20 +0000 (15:06 +0800)]
igb: use igb_adapter->io_addr instead of e1000_hw->hw_addr
When running as guest, under certain condition, it will oops as following.
writel() in igb_configure_tx_ring() results in oops, because hw->hw_addr
is NULL. While other register access won't oops kernel because they use
wr32/rd32 which have a defense against NULL pointer.
Chris J Arges [Wed, 2 Nov 2016 14:13:42 +0000 (09:13 -0500)]
igb: Workaround for igb i210 firmware issue
Sometimes firmware may not properly initialize I347AT4_PAGE_SELECT causing
the probe of an igb i210 NIC to fail. This patch adds an addition zeroing
of this register during igb_get_phy_id to workaround this issue.
Thanks for Jochen Henneberg for the idea and original patch.
khalidm [Mon, 17 Oct 2016 16:51:08 +0000 (09:51 -0700)]
e1000e: driver trying to free already-free irq
During systemd reboot sequence network driver interface is shutdown
by e1000_close. The PCI driver interface is shut by e1000_shutdown.
The e1000_shutdown checks for netif_running status, if still up it
brings down driver. But it disables msi outside of this if statement,
regardless of netif status. All this is OK when e1000_close happens
after shutdown. However, by default, everything in systemd is done
in parallel. This creates a conditions where e1000_shutdown is called
after e1000_close, therefore hitting BUG_ON assert in free_msi_irqs.
Linus Torvalds [Fri, 6 Jan 2017 07:17:41 +0000 (23:17 -0800)]
Merge tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Just two small fixes for platform drivers x86:
- use brightness_set_blocking for LED-setting callbacks on Fujitsu
laptops
- fix surface3_button build errors"
* tag 'platform-drivers-x86-v4.10-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: fujitsu-laptop: use brightness_set_blocking for LED-setting callbacks
platform/x86: fix surface3_button build errors
Linus Torvalds [Fri, 6 Jan 2017 07:06:06 +0000 (23:06 -0800)]
Merge branch 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two small fixes relating to audit's use of fsnotify.
The first patch plugs a leak and the second fixes some lock
shenanigans. The patches are small and I banged on this for an
afternoon with our testsuite and didn't see anything odd"
* 'stable-4.10' of git://git.infradead.org/users/pcmoore/audit:
audit: Fix sleep in atomic
fsnotify: Remove fsnotify_duplicate_mark()
Linus Torvalds [Thu, 5 Jan 2017 23:06:02 +0000 (15:06 -0800)]
Merge tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a bunch of drm/i915 fixes for v4.10-rc3. It includes GVT-g
fixes.
My new year's resolution is to start using signed tags for pulls. If
that feels like a déjà vu, it's ((new year's) resolution), not (new
(year's resolution))"
[ Taking this directly from Jani because Dave Airlie is only partially
connected right now. - Linus ]
* tag 'drm-intel-fixes-2017-01-05' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Prevent timeline updates whilst performing reset
drm/i915: Silence allocation failure during sg_trim()
drm/i915: Don't clflush before release phys object
drm/i915: Fix oops in overlay due to frontbuffer tracking
drm/i915: Fix oopses in the overlay code due to i915_gem_active stuff
drm/i915: Initialize overlay->last_flip properly
drm/i915: Move the min_pixclk[] handling to the end of readout
drm/i915: Force VDD off on the new power seqeuencer before starting to use it
drm/i915/gvt: fix typo in cfg_space range check
drm/i915/gvt: fix an issue in emulating cfg space PCI_COMMAND
drm/i915/gvt/kvmgt: trival: code cleanup
drm/i915/gvt/kvmgt: prevent double-release of vgpu
drm/i915/gvt/kvmgt: check returned slot for gfn
drm/i915/gvt/kvmgt: dereference the pointer within lock
drm/i915/gvt: reset the GGTT entry when vGPU created
drm/i915/gvt: fix an error in opregion handling
tools: psock_tpacket: block Rx until socket filter has been added and socket has been bound to loopback.
Packets from any/all interfaces may be queued up on the PF_PACKET socket
before it is bound to the loopback interface by psock_tpacket, and
when these are passed up by the kernel, they could interfere
with the Rx tests.
Avoid interference from spurious packet by blocking Rx until the
socket filter has been set up, and the packet has been bound to the
desired (lo) interface. The effective sequence is
socket(PF_PACKET, SOCK_RAW, 0);
set up ring
Invoke SO_ATTACH_FILTER
bind to sll_protocol set to ETH_P_ALL, sll_ifindex for lo
After this sequence, the only packets that will be passed up are
those received on loopback that pass the attached filter.
For TCP sockets, TX timestamps are only captured when the user data
is successfully and fully written to the socket. In many cases,
however, TCP writes can be partial for which no timestamp is
collected.
Collect timestamps whenever any user data is (fully or partially)
copied into the socket. Pass tcp_write_queue_tail to tcp_tx_timestamp
instead of the local skb pointer since it can be set to NULL on
the error path.
Note that tcp_write_queue_tail can be NULL, even if bytes have been
copied to the socket. This is because acknowledgements are being
processed in tcp_sendmsg(), and by the time tcp_tx_timestamp is
called tcp_write_queue_tail can be NULL. For such cases, this patch
does not collect any timestamps (i.e., it is best-effort).
This patch is written with suggestions from Willem de Bruijn and
Eric Dumazet.
Change-log V1 -> V2:
- Use sockc.tsflags instead of sk->sk_tsflags.
- Use the same code path for normal writes and errors.
Alan Stern [Mon, 19 Dec 2016 17:03:41 +0000 (12:03 -0500)]
USB: fix problems with duplicate endpoint addresses
When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
Linus Torvalds [Thu, 5 Jan 2017 18:36:56 +0000 (10:36 -0800)]
Merge tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Three small pin control fixes for the v4.10 series. Very little to say
about them, just driver fixes.
- one fix to the AMD pinctrl ACPI glue
- fix requests on the Meson driver
- fix bitfield widths on Samsungs Exynos 5433"
* tag 'pinctrl-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: samsung: Fix the width of PINCFG_TYPE_DRV bitfields for Exynos5433
pinctrl: meson: fix gpio request disabling other modes
pinctrl/amd: Set the level based on ACPI tables
Peter Rosin [Thu, 22 Dec 2016 07:43:55 +0000 (08:43 +0100)]
usb: ohci-at91: use descriptor-based gpio APIs correctly
The gpiod_get* function family does not want the -gpio suffix.
Use devm_gpiod_get_index_optional instead of devm_gpiod_get_optional.
The descriptor based APIs handle active high/low automatically.
The vbus-gpios are output, request enable while getting the gpio.
Don't try to get any vbus-gpios for ports outside num-ports.
WTF? Big sigh.
Fixes: 054d4b7b577d ("usb: ohci-at91: Use descriptor-based gpio APIs") Signed-off-by: Peter Rosin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Linus Torvalds [Thu, 5 Jan 2017 18:32:16 +0000 (10:32 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather large set of bugfixes, as we just returned from the
Christmas break. Most of these are relatively unimportant fixes for
regressions introduced during the merge window, and about half of the
changes are for mach-omap2.
A couple of patches are just cleanups and dead code removal that I
would not normally have considered for merging after -rc2, but I
decided to take them along with the fixes this time.
Notable fixes include:
- removing the skeleton.dtsi include broke a number of machines, and
we have to put empty /chosen nodes back to be able to pass kernel
command lines as before
- enabling Samsung platforms no longer hardwires CONFIG_HZ to 200, as
it had been for no good reason for a long time"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
drivers: psci: annotate timer on stack to silence odebug messages
ARM64: defconfig: enable DRM_MESON as module
ARM64: dts: meson-gx: Add Graphic Controller nodes
ARM64: dts: meson-gxl: fix GPIO include
ARM: dts: imx6: Disable "weim" node in the dtsi files
ARM: dts: qcom: apq8064: Add missing scm clock
ARM: davinci: da8xx: Fix sleeping function called from invalid context
ARM: davinci: Make __clk_{enable,disable} functions public
ARM: davinci: da850: don't add emac clock to lookup table twice
ARM: davinci: da850: fix infinite loop in clk_set_rate()
ARM: i.MX: remove map_io callback
ARM: dts: vf610-zii-dev-rev-b: Add missing newline
ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
ARM: dts: imx31: fix AVIC base address
ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
arm64: dts: vexpress: Support GICC_DIR operations
ARM: dts: vexpress: Support GICC_DIR operations
firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares
arm64: dts: msm8996: Add required memory carveouts
...
Linus Torvalds [Thu, 5 Jan 2017 18:29:40 +0000 (10:29 -0800)]
Merge tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes and cleanups from Juergen Gross:
- small fixes for xenbus driver
- one fix for xen dom0 boot on huge system
- small cleanups
* tag 'for-linus-4.10-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen: ARM: Zero reserved fields of xatp before making hypervisor call
xen: events: Replace BUG() with BUG_ON()
xen: remove stale xs_input_avail() from header
xen: return xenstore command failures via response instead of rc
xen: xenbus driver must not accept invalid transaction ids
xen/evtchn: use rb_entry()
xen/setup: Don't relocate p2m over existing one
usb: hub: Move hub_port_disable() to fix warning if PM is disabled
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
projects / linux.git / log