With some gcc versions, we get a warning about the eicon driver,
and that currently shows up as the only remaining warning in one
of the build bots:
In file included from ../drivers/isdn/hardware/eicon/message.c:30:0:
eicon/message.c: In function 'mixer_notify_update':
eicon/platform.h:333:18: warning: array subscript is above array bounds [-Warray-bounds]
The code is easily changed to open-code the unusual PUT_WORD() line
causing this to avoid the warning.
this is a pull request of 4 patches for net-next/master.
The first patch by Oliver Hartkopp adds a netlink API to configure the
interface termination of a CAN card. The next two patches are by me and
add a netlink API to query and configure CAN interfaces that only
support fixed bitrates. The last patch by Colin Ian King simplifies the
return path in the softing_cs driver's softingcs_probe() function.
====================
David S. Miller [Fri, 27 Jan 2017 15:39:10 +0000 (10:39 -0500)]
Merge branch 'gtp-fixes'
Andreas Schultz says:
====================
various gtp fixes
I'm sorry for the compile error mess up in the last version.
It's no excuse for not test compiling, but the hunks got lost in
a rebase.
This is the part of the previous "simple gtp improvements" series
that Pablo indicated should go into net.
The addition of the module alias fixes genl family autoloading,
clearing the DF bit fixes a protocol violation in regard to the
specification and the netns comparison fixes a corner case of
cross netns recv.
v2->v3: fix compiler error introduced in rebase
====================
Andreas Schultz [Fri, 27 Jan 2017 09:40:58 +0000 (10:40 +0100)]
gtp: fix cross netns recv on gtp socket
The use of the passed through netlink src_net to check for a
cross netns operation was wrong. Using the GTP socket and the
GTP netdevice is always correct (even if the netdev has been
moved to new netns after link creation).
Andreas Schultz [Fri, 27 Jan 2017 09:40:57 +0000 (10:40 +0100)]
gtp: clear DF bit on GTP packet tx
3GPP TS 29.281 and 3GPP TS 29.060 imply that GTP-U packets should be
sent with the DF bit cleared. For example 3GPP TS 29.060, Release 8,
Section 13.2.2:
> Backbone router: Any router in the backbone may fragment the GTP
> packet if needed, according to IPv4.
Pablo Neira [Thu, 26 Jan 2017 21:56:21 +0000 (22:56 +0100)]
tcp: don't annotate mark on control socket from tcp_v6_send_response()
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5f8 ("tcp: fix mark propagation with fwmark_reflect enabled") Suggested-by: Eric Dumazet <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Felix Jia [Thu, 26 Jan 2017 03:59:17 +0000 (16:59 +1300)]
net/ipv6: allow sysctl to change link-local address generation mode
The address generation mode for IPv6 link-local can only be configured
by netlink messages. This patch adds the ability to change the address
generation mode via sysctl.
v1 -> v2
Removed the rtnl lock and switch to use RCU lock to iterate through
the netdev list.
v2 -> v3
Removed the addrgenmode variable from the idev structure and use the
systcl storage for the flag.
Simplifed the logic for sysctl handling by removing the supported
for all operation.
Added support for more types of tunnel interfaces for link-local
address generation.
Florian Fainelli [Thu, 26 Jan 2017 22:44:17 +0000 (14:44 -0800)]
net: Fix ndo_setup_tc comment
Commit 16e5cc647173 ("net: rework setup_tc ndo op to consume
general tc operand") changed the ndo_setup_tc() signature, but did not
update the comments in netdevice.h, so do that now.
Linus Torvalds [Fri, 27 Jan 2017 02:04:56 +0000 (18:04 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc6-part-two' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"This is the main request for rc6, since really the one earlier was the
rc5 one :-)
The main thing are the nouveau specific race fixes for the connector
locking bug we fixed in -next and reverted here as it has quite large
prereqs. These two fixes should solve the problem at that level and we
can fix it properly in 4.11
Otherwise i915 has a bunch of changes, one ABI change for GVT related
stuff, some VC4 leak fixes, one core fence fix and some AMD changes,
oh and one ast hang avoidance fix.
Hoping it calms down around now"
* tag 'drm-fixes-for-v4.10-rc6-part-two' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/nouveau: Handle fbcon suspend/resume in seperate worker
drm/nouveau: Don't enabling polling twice on runtime resume
drm/ast: Fixed system hanged if disable P2A
Revert "drm/radeon: always apply pci shutdown callbacks"
drm/i915: reinstate call to trace_i915_vma_bind
drm/i915: Move atomic state free from out of fence release
drm/i915: Check for NULL atomic state in intel_crtc_disable_noatomic()
drm/i915: Fix calculation of rotated x and y offsets for planar formats
drm/i915: Don't init hpd polling for vlv and chv from runtime_suspend()
drm/i915: Don't leak edid in intel_crt_detect_ddc()
drm/i915: Release temporary load-detect state upon switching
drm/i915: prevent crash with .disable_display parameter
drm/i915: Avoid drm_atomic_state_put(NULL) in intel_display_resume
MAINTAINERS: update new mail list for intel gvt driver
drm/i915/gvt: Fix kmem_cache_create() name
drm/i915/gvt/kvmgt: mdev ABI is available_instances, not available_instance
drm/amdgpu: fix unload driver issue for virtual display
drm/amdgpu: check ring being ready before using
drm/vc4: Return -EINVAL on the overflow checks failing.
drm/vc4: Fix an integer overflow in temporary allocation layout.
...
Dave Airlie [Fri, 27 Jan 2017 01:29:44 +0000 (11:29 +1000)]
Merge tag 'drm-intel-fixes-2017-01-26' of git://anongit.freedesktop.org/git/drm-intel into drm-fixes
More fixes than I'd like at this stage, but I think the holidays and
conferences have delayed finding and fixing the stuff a bit. Almost all
of them have Fixes: tags, so it's not just random fixes, we can point
fingers at the commits that broke stuff.
There's an ABI fix to GVT from Alex, before we go on an release a kernel
with the wrong attribute name.
* tag 'drm-intel-fixes-2017-01-26' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: reinstate call to trace_i915_vma_bind
drm/i915: Move atomic state free from out of fence release
drm/i915: Check for NULL atomic state in intel_crtc_disable_noatomic()
drm/i915: Fix calculation of rotated x and y offsets for planar formats
drm/i915: Don't init hpd polling for vlv and chv from runtime_suspend()
drm/i915: Don't leak edid in intel_crt_detect_ddc()
drm/i915: Release temporary load-detect state upon switching
drm/i915: prevent crash with .disable_display parameter
drm/i915: Avoid drm_atomic_state_put(NULL) in intel_display_resume
MAINTAINERS: update new mail list for intel gvt driver
drm/i915/gvt: Fix kmem_cache_create() name
drm/i915/gvt/kvmgt: mdev ABI is available_instances, not available_instance
drm/i915/gvt: Fix relocation of shadow bb
drm/i915/gvt: Enable the shadow batch buffer
Linus Torvalds [Fri, 27 Jan 2017 01:27:00 +0000 (17:27 -0800)]
Merge tag 'acpi-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two regressions introduced recently, one by reverting the
problematic commit and one by fixing up locking in the ACPICA core.
Specifics:
- Revert a recent change that added an ACPI video blacklist entry for
HP Pavilion dv6 as it turned to introduce backlight handling
regressions on some systems (Hans de Goede).
- Fix locking in the ACPICA core to avoid deadlocks related to table
loading that were exposed by a recent change in that area (Lv
Zheng)"
* tag 'acpi-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / video: Add force_native quirk for HP Pavilion dv6"
ACPICA: Tables: Fix hidden logic related to acpi_tb_install_standard_table()
Linus Torvalds [Fri, 27 Jan 2017 01:14:17 +0000 (17:14 -0800)]
Merge tag 'pm-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two regressions introduced recently, one by reverting the
problematic commit and one by fixing up the behavior in an overlooked
case.
Specifics:
- Revert the recent change that caused suspend-to-idle to be used as
the default suspend method on systems where it is indicated to be
efficient by the ACPI tables, as that turned out to be premature
and introduced suspend regressions on some systems with missing
power management support in device drivers (Rafael Wysocki).
- Fix up the intel_pstate driver to take changes of the global limits
via sysfs correctly when the performance policy is used which has
been broken by a recent change in it (Srinivas Pandruvada)"
* tag 'pm-4.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix sysfs limits enforcement for performance policy
Revert "PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag"
Lyude Paul [Thu, 12 Jan 2017 02:25:24 +0000 (21:25 -0500)]
drm/nouveau: Handle fbcon suspend/resume in seperate worker
Resuming from RPM can happen while already holding
dev->mode_config.mutex. This means we can't actually handle fbcon in
any RPM resume workers, since restoring fbcon requires grabbing
dev->mode_config.mutex again. So move the fbcon suspend/resume code into
it's own worker, and rely on that instead to avoid deadlocking.
This fixes more deadlocks for runtime suspending the GPU on the ThinkPad
W541. Reproduction recipe:
- Get a machine with both optimus and a nvidia card with connectors
attached to it
- Wait for the nvidia GPU to suspend
- Attempt to manually reprobe any of the connectors on the nvidia GPU
using sysfs
- *deadlock*
[airlied: use READ_ONCE to address Hans's comment]
Lyude Paul [Thu, 12 Jan 2017 02:25:23 +0000 (21:25 -0500)]
drm/nouveau: Don't enabling polling twice on runtime resume
As it turns out, on cards that actually have CRTCs on them we're already
calling drm_kms_helper_poll_enable(drm_dev) from
nouveau_display_resume() before we call it in
nouveau_pmops_runtime_resume(). This leads us to accidentally trying to
enable polling twice, which results in a potential deadlock between the
RPM locks and drm_dev->mode_config.mutex if we end up trying to enable
polling the second time while output_poll_execute is running and holding
the mode_config lock. As such, make sure we only enable polling in
nouveau_pmops_runtime_resume() if we need to.
Y.C. Chen [Thu, 26 Jan 2017 01:45:40 +0000 (09:45 +0800)]
drm/ast: Fixed system hanged if disable P2A
The original ast driver will access some BMC configuration through P2A bridge
that can be disabled since AST2300 and after.
It will cause system hanged if P2A bridge is disabled.
Here is the update to fix it.
Dave Airlie [Fri, 27 Jan 2017 00:33:39 +0000 (10:33 +1000)]
Merge tag 'drm-vc4-fixes-2017-01-23' of https://github.com/anholt/linux into drm-fixes
This pull request brings in a few little error checking fixes and one
slow memory leak fix.
* tag 'drm-vc4-fixes-2017-01-23' of https://github.com/anholt/linux:
drm/vc4: Return -EINVAL on the overflow checks failing.
drm/vc4: Fix an integer overflow in temporary allocation layout.
drm/vc4: fix a bounds check
drm/vc4: Fix memory leak of the CRTC state.
Dave Airlie [Fri, 27 Jan 2017 00:17:43 +0000 (10:17 +1000)]
Merge branch 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a few small fixes.
* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon: always apply pci shutdown callbacks"
drm/amdgpu: fix unload driver issue for virtual display
drm/amdgpu: check ring being ready before using
Dave Airlie [Fri, 27 Jan 2017 00:16:56 +0000 (10:16 +1000)]
Merge tag 'drm-misc-fixes-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Single fence fix.
* tag 'drm-misc-fixes-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc:
drm/fence: fix memory overwrite when setting out_fence fd
Omar Sandoval [Thu, 26 Jan 2017 01:06:39 +0000 (17:06 -0800)]
Btrfs: disable xattr operations on subvolume directories
When you snapshot a subvolume containing a subvolume, you get a
placeholder directory where the subvolume would be. These directory
inodes have ->i_ops set to btrfs_dir_ro_inode_operations. Previously,
these i_ops didn't include the xattr operation callbacks. The conversion
to xattr_handlers missed this case, leading to bogus attempts to set
xattrs on these inodes. This manifested itself as failures when running
delayed inodes.
To fix this, clear IOP_XATTR in ->i_opflags on these inodes.
Omar Sandoval [Thu, 26 Jan 2017 01:06:38 +0000 (17:06 -0800)]
Btrfs: remove old tree_root case in btrfs_read_locked_inode()
As Jeff explained in c2951f32d36c ("btrfs: remove old tree_root dirent
processing in btrfs_real_readdir()"), supporting this old format is no
longer necessary since the Btrfs magic number has been updated since we
changed to the current format. There are other places where we still
handle this old format, but since this is part of a fix that is going to
stable, I'm only removing this one for now.
Kazuya Mizuguchi [Thu, 26 Jan 2017 13:29:27 +0000 (14:29 +0100)]
ravb: unmap descriptors when freeing rings
"swiotlb buffer is full" errors occur after repeated initialisation of a
device - f.e. suspend/resume or ip link set up/down. This is because memory
mapped using dma_map_single() in ravb_ring_format() and ravb_start_xmit()
is not released. Resolve this problem by unmapping descriptors when
freeing rings.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Kazuya Mizuguchi <[email protected]>
[simon: reworked] Signed-off-by: Simon Horman <[email protected]> Acked-by: Sergei Shtylyov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
This happens when the loopback device is set down and a ipv6 fib route
dump is requested.
ip6_null_entry is the root of all ipv6 fib tables making it integrated
into the table and hence passed to the ipv6 route dump code. The
null_entry route uses the loopback device for dst.dev but may not have
rt6i_idev set because of the order in which initializations are done --
ip6_route_net_init is run before addrconf_init has initialized the
loopback device. Fixing the initialization order is a much bigger problem
with no obvious solution thus far.
The BUG is triggered when the loopback is set down and the netif_running
check added by a1a22c1206 fails. The fill_node descends to checking
rt->rt6i_idev for ignore_routes_with_linkdown and since rt6i_idev is
NULL it faults.
The null_entry route should not be processed in a dump request. Catch
and ignore. This check is done in rt6_dump_route as it is the highest
place in the callchain with knowledge of both the route and the network
namespace.
Fixes: a1a22c1206("net: ipv6: Keep nexthop of multipath route on admin down") Signed-off-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David Ahern [Thu, 26 Jan 2017 22:08:36 +0000 (14:08 -0800)]
net: ipv6: remove skb_reserve in getroute
Remove skb_reserve and skb_reset_mac_header from inet6_rtm_getroute. The
allocated skb is not passed through the routing engine (like it is for
IPv4) and has not since the beginning of git time.
This patch series extracts the 4 patches of the larger: net: dsa: Support for
pdata in dsa2 while we wait for feedback from Greg KH on the device references.
Changes in v2:
- rebased properly after the multi-MDIO bus support added to mv88e6xxx
====================
Florian Fainelli [Thu, 26 Jan 2017 18:45:54 +0000 (10:45 -0800)]
net: dsa: Move ports assignment closer to error checking
Move the assignment of ports in _dsa_register_switch() closer to where
it is checked, no functional change. Re-order declarations to be
preserve the inverted christmas tree style.
Florian Fainelli [Thu, 26 Jan 2017 18:45:52 +0000 (10:45 -0800)]
net: dsa: Make most functions take a dsa_port argument
In preparation for allowing platform data, and therefore no valid
device_node pointer, make most DSA functions takes a pointer to a
dsa_port structure whenever possible. While at it, introduce a
dsa_port_is_valid() helper function which checks whether port->dn is
NULL or not at the moment.
Florian Fainelli [Thu, 26 Jan 2017 18:45:51 +0000 (10:45 -0800)]
net: dsa: Pass device pointer to dsa_register_switch
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
David S. Miller [Thu, 26 Jan 2017 19:31:08 +0000 (14:31 -0500)]
Merge tag 'batadv-next-for-davem-20170126' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- ignore self-generated loop detect MAC addresses in translation table,
by Simon Wunderlich
- install uapi batman_adv.h header, by Sven Eckelmann
- bump copyright years, by Sven Eckelmann
- Remove an unused variable in translation table code, by Sven Eckelmann
- Handle NET_XMIT_CN like NET_XMIT_SUCCESS (revised according to Davids
suggestion), and a follow up code clean up, by Gao Feng (2 patches)
====================
Arnd Bergmann [Wed, 25 Jan 2017 22:15:53 +0000 (23:15 +0100)]
ISDN: eicon: reduce stack size of sig_ind function
I noticed that this function uses a lot of kernel stack when the
"latent entropy" plugin is enabled:
drivers/isdn/hardware/eicon/message.c: In function 'sig_ind':
drivers/isdn/hardware/eicon/message.c:6113:1: error: the frame size of 1168 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
We currently don't warn about this, as we raise the warning limit
to 2048 bytes in mainline, but I'd like to lower that limit again
in the future, and this function can easily be changed to be more
efficient and avoid that warning, by making some of its local
variables 'const'.
The following patchset contains a large batch with Netfilter fixes for
your net tree, they are:
1) Two patches to solve conntrack garbage collector cpu hogging, one to
remove GC_MAX_EVICTS and another to look at the ratio (scanned entries
vs. evicted entries) to make a decision on whether to reduce or not
the scanning interval. From Florian Westphal.
2) Two patches to fix incorrect set element counting if NLM_F_EXCL is
is not set. Moreover, don't decrenent set->nelems from abort patch
if -ENFILE which leaks a spare slot in the set. This includes a
patch to deconstify the set walk callback to update set->ndeact.
3) Two fixes for the fwmark_reflect sysctl feature: Propagate mark to
reply packets both from nf_reject and local stack, from Pau Espin Pedrol.
4) Fix incorrect handling of loopback traffic in rpfilter and nf_tables
fib expression, from Liping Zhang.
5) Fix oops on stateful objects netlink dump, when no filter is specified.
Also from Liping Zhang.
6) Fix a build error if proc is not available in ipt_CLUSTERIP, related
to fix that was applied in the previous batch for net. From Arnd Bergmann.
7) Fix lack of string validation in table, chain, set and stateful
object names in nf_tables, from Liping Zhang. Moreover, restrict
maximum log prefix length to 127 bytes, otherwise explicitly bail
out.
8) Two patches to fix spelling and typos in nf_tables uapi header file
and Kconfig, patches from Alexander Alemayhu and William Breathitt Gray.
====================
Darrick J. Wong [Thu, 26 Jan 2017 17:50:30 +0000 (09:50 -0800)]
xfs: fix bmv_count confusion w/ shared extents
In a bmapx call, bmv_count is the total size of the array, including the
zeroth element that userspace uses to supply the search key. The output
array starts at offset 1 so that we can set up the user for the next
invocation. Since we now can split an extent into multiple bmap records
due to shared/unshared status, we have to be careful that we don't
overflow the output array.
In the original patch f86f403794b ("xfs: teach get_bmapx about shared
extents and the CoW fork") I used cur_ext (the output index) to check
for overflows, albeit with an off-by-one error. Since nexleft no longer
describes the number of unfilled slots in the output, we can rip all
that out and use cur_ext for the overflow check directly.
Failure to do this causes heap corruption in bmapx callers such as
xfs_io and xfs_scrub. xfs/328 can reproduce this problem.
Linus Torvalds [Thu, 26 Jan 2017 17:08:49 +0000 (09:08 -0800)]
Merge tag 'pinctrl-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"A bunch of pin control fixes for v4.10 that didn't get sent off until
now, sorry for the delay.
It's only driver fixes:
- A bunch of fixes to the Intel drivers: broxton, baytrail. Bugs
related to register offsets, IRQ, debounce functionality.
- Fix a conflict amongst UART settings on the meson.
- Fix the ethernet setting on the Uniphier.
- A compilation warning squelched"
* tag 'pinctrl-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix Ethernet (RMII) pin-mux setting for LD20
pinctrl: meson: fix uart_ao_b for GXBB and GXL/GXM
pinctrl: amd: avoid maybe-uninitalized warning
pinctrl: baytrail: Do not add all GPIOs to IRQ domain
pinctrl: baytrail: Rectify debounce support
pinctrl: intel: Set pin direction properly
pinctrl: broxton: Use correct PADCFGLOCK offset
Bart Van Assche [Wed, 25 Jan 2017 21:43:56 +0000 (13:43 -0800)]
Revert "sd: remove __data_len hack for WRITE SAME"
This patch reverts commit f80de881d8df and avoids that sending a
WRITE SAME command to the iSCSI initiator triggers the following:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000014
TARGET_CORE[iSCSI]: Expected Transfer Length: 260096 does not match SCSI CDB Length: 512 for SAM Opcode: 0x41
IP: iscsi_tcp_segment_done+0x20b/0x310 [libiscsi_tcp]
Linus Torvalds [Thu, 26 Jan 2017 16:55:33 +0000 (08:55 -0800)]
Merge tag 'drm-fixes-for-v4.10-rc6-revert-one' of git://people.freedesktop.org/~airlied/linux
Pull drm revert from Dave Airlie:
"Revert one patch missing some prereqs.
One of the connector fixes was missing some prereqs, we have an
alternate driver fix that should work that I'll send tomorrow.
Today is a holiday here so quickly smashing this out"
Daniel Vetter explains:
"I pushed a locking change to fix a nouveau rpm issue to -fixes that
needed the connector_list rework. And that's only in -next, but I
missed that. Dave has the revert in a pull, and he'll follow-up with
the hack nouveau patch for 4.10, and then we'll reapply the proper fix
again for -next and revert the hacks. A bit a mess, but should be
sorted soon"
* tag 'drm-fixes-for-v4.10-rc6-revert-one' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/probe-helpers: Drop locking from poll_enable"
Parav Pandit [Thu, 19 Jan 2017 15:55:08 +0000 (09:55 -0600)]
nvmet-rdma: Fix missing dma sync to nvme data structures
This patch performs dma sync operations on nvme_command
and nvme_completion.
nvme_command is synced
(a) on receiving of the recv queue completion for cpu access.
(b) before posting recv wqe back to rdma adapter for device access.
nvme_completion is synced
(a) on receiving of the recv queue completion of associated
nvme_command for cpu access.
(b) before posting send wqe to rdma adapter for device access.
This patch is generated for git://git.infradead.org/nvme-fabrics.git
Branch: nvmf-4.10
Sagi Grimberg [Sun, 1 Jan 2017 11:18:26 +0000 (13:18 +0200)]
nvmet: Call fatal_error from keep-alive timout expiration
We only need to call delete_ctrl once, so given that both
keep-alive timeout and any other fatal error can trigger it,
just make sure we only call delete_ctrl once.
Sagi Grimberg [Sun, 27 Nov 2016 20:29:17 +0000 (22:29 +0200)]
nvmet: delete controllers deletion upon subsystem release
No reason for them to be kept around if we are
deleting the subsystem, so instead of passively
wait for the host to disconnect, actively delete
the controllers.
Gao Feng [Mon, 21 Nov 2016 15:00:32 +0000 (23:00 +0800)]
batman-adv: Treat NET_XMIT_CN as transmit successfully
The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packet is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So batman-adv should handle NET_XMIT_CN also as NET_XMIT_SUCCESS.
Sven Eckelmann [Sun, 11 Dec 2016 12:16:07 +0000 (13:16 +0100)]
uapi: install batman_adv.h header
09748a22f4ab ("batman-adv: add generic netlink family for batman-adv")
introduced the new batman_adv.h which describes the netlink attributes and
commands of batman-adv. But the Kbuild entry to install the header was not
added.
All currently known tools ship their own copy of batman_adv.h but it should
be installed anyway to later be able to migrate to the system batman_adv.h.
Simon Wunderlich [Thu, 24 Nov 2016 15:11:01 +0000 (16:11 +0100)]
batman-adv: don't add loop detect macs to TT
The bridge loop avoidance (BLA) feature of batman-adv sends packets to
probe for Mesh/LAN packet loops. Those packets are not sent by real
clients and should therefore not be added to the translation table (TT).
Darrick J. Wong [Thu, 26 Jan 2017 04:24:57 +0000 (20:24 -0800)]
xfs: clear _XBF_PAGES from buffers when readahead page
If we try to allocate memory pages to back an xfs_buf that we're trying
to read, it's possible that we'll be so short on memory that the page
allocation fails. For a blocking read we'll just wait, but for
readahead we simply dump all the pages we've collected so far.
Unfortunately, after dumping the pages we neglect to clear the
_XBF_PAGES state, which means that the subsequent call to xfs_buf_free
thinks that b_pages still points to pages we own. It then double-frees
the b_pages pages.
This results in screaming about negative page refcounts from the memory
manager, which xfs oughtn't be triggering. To reproduce this case,
mount a filesystem where the size of the inodes far outweighs the
availalble memory (a ~500M inode filesystem on a VM with 300MB memory
did the trick here) and run bulkstat in parallel with other memory
eating processes to put a huge load on the system. The "check summary"
phase of xfs_scrub also works for this purpose.
Arnd Bergmann [Wed, 25 Jan 2017 22:29:33 +0000 (23:29 +0100)]
bridge: move maybe_deliver_addr() inside #ifdef
The only caller of this new function is inside of an #ifdef checking
for CONFIG_BRIDGE_IGMP_SNOOPING, so we should move the implementation
there too, in order to avoid this harmless warning:
net/bridge/br_forward.c:177:13: error: 'maybe_deliver_addr' defined but not used [-Werror=unused-function]
Daniel Borkmann [Wed, 25 Jan 2017 23:42:49 +0000 (00:42 +0100)]
bpf: use prefix_len in test_tag when reading fdinfo
We currently used len instead of prefix_len for the strncmp() in
fdinfo on the prog_tag. It still worked as we matched on the correct
output line also with first 8 instead of 10 chars, but lets fix it
properly to use the intended length.
Fixes: 62b64660262a ("bpf: add prog tag test case to bpf selftests") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
I will probably need to use broadcom.ko for PHY connected to interface
of bgmac supported device so I started looking at it willing to
understand it better.
I found AUXCTL part of the driver / lib a bit confusing and hard to read
so I'm trying to clean it up a bit. I hope this patchset makes following
AUXCTL operations much easier making it clear which defines are for
registers and which for values.
There is no functional change in this pachset.
====================
Rafał Miłecki [Wed, 25 Jan 2017 20:00:27 +0000 (21:00 +0100)]
net: phy: bcm-phy-lib: clean up remaining AUXCTL register defines
1) Use 0x%02x format for register number. This follows some other
defines and makes it easier to distinct register from values.
2) Put register define above values and sort the values. It makes
reading header code easier.
3) Use 0x%04x format for all values. It's about consistency with other
values (and most of the header) not a personal preference.
4) Separate define for reading shift value with an extre empty line.
It's user for all AUXCTL registers in a bcm54xx_auxctl_read.
Rafał Miłecki [Wed, 25 Jan 2017 20:00:25 +0000 (21:00 +0100)]
net: phy: broadcom: use auxctl reading helper in BCM54612E code
Starting with commit 5b4e29005123 ("net: phy: broadcom: add
bcm54xx_auxctl_read") we have a reading helper so use it and avoid code
duplication.
It also means we don't need MII_BCM54XX_AUXCTL_SHDWSEL_MISC define as
it's the same as MII_BCM54XX_AUXCTL_SHDWSEL_MISC just for reading needs
(same value shifted by 12 bits).
Jakub Kicinski [Wed, 25 Jan 2017 22:56:36 +0000 (14:56 -0800)]
virtio_net: reject XDP programs using header adjustment
commit 17bedab27231 ("bpf: xdp: Allow head adjustment in XDP prog")
added a new XDP helper to prepend and remove data from a frame.
Make virtio_net reject programs making use of this helper until
proper support is added.
John Fastabend [Thu, 26 Jan 2017 02:22:48 +0000 (18:22 -0800)]
virtio_net: use dev_kfree_skb for small buffer XDP receive
In the small buffer case during driver unload we currently use
put_page instead of dev_kfree_skb. Resolve this by adding a check
for virtnet mode when checking XDP queue type. Also name the
function so that the code reads correctly to match the additional
check.
David S. Miller [Thu, 26 Jan 2017 03:47:31 +0000 (22:47 -0500)]
Merge branch 'r8152-napi-fixes'
Hayes Wang says:
====================
r8152: fix scheduling napi
v3:
simply the argument for patch #3. Replace &tp->napi with napi.
v2:
Add smp_mb__after_atomic() for patch #1.
v1:
Scheduling the napi during the following periods would let it be ignored.
And the events wouldn't be handled until next napi_schedule() is called.
1. after napi_disable and before napi_enable().
2. after all actions of napi function is completed and before calling
napi_complete().
If no next napi_schedule() is called, tx or rx would stop working.
In order to avoid these situations, the followings solutions are applied.
1. prevent start_xmit() from calling napi_schedule() during runtime suspend
or after napi_disable().
2. re-schedule the napi for tx if it is necessary.
3. check if any rx is finished or not after napi_enable().
====================
hayeswang [Thu, 26 Jan 2017 01:38:33 +0000 (09:38 +0800)]
r8152: re-schedule napi for tx
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Florian Fainelli [Wed, 25 Jan 2017 17:10:41 +0000 (09:10 -0800)]
net: dsa: Bring back device detaching in dsa_slave_suspend()
Commit 448b4482c671 ("net: dsa: Add lockdep class to tx queues to avoid
lockdep splat") removed the netif_device_detach() call done in
dsa_slave_suspend() which is necessary, and paired with a corresponding
netif_device_attach(), bring it back.
Fixes: 448b4482c671 ("net: dsa: Add lockdep class to tx queues to avoid lockdep splat") Signed-off-by: Florian Fainelli <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Andrew Lunn [Wed, 25 Jan 2017 14:04:17 +0000 (15:04 +0100)]
net: dsa: Mop up remaining NET_DSA_HWMON references
Previous patches have moved the temperature sensor code into the
Marvell PHYs. A few now dead references to NET_DSA_HWMON were left
behind. Go reap them.
Tomáš Pilař [Wed, 25 Jan 2017 13:48:17 +0000 (13:48 +0000)]
sfc: reduce severity of PIO buffer alloc failures
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
David S. Miller [Wed, 25 Jan 2017 19:42:37 +0000 (14:42 -0500)]
Merge branch 'thunderx-ethtool'
Sunil Goutham says:
====================
thunderx: More ethtool support and BGX configuration changes
These patches adds support to set queue sizes from ethtool and changes
the way serdes lane configuration is done by BGX driver on 81/83xx
platforms.
====================
Sunil Goutham [Wed, 25 Jan 2017 12:06:24 +0000 (17:36 +0530)]
net: thunderx: Leave serdes lane config on 81/83xx to firmware
For DLMs and SLMs on 80/81/83xx, many lane configurations
across different boards are coming up. Also kernel doesn't have
any way to identify board type/info and since firmware does,
just get rid of figuring out lane to serdes config and take
whatever has been programmed by low level firmware.
Sunil Goutham [Wed, 25 Jan 2017 12:06:23 +0000 (17:36 +0530)]
net: thunderx: Support to configure queue sizes from ethtool
Adds support to set Rx/Tx queue sizes from ethtool. Fixes
an issue with retrieving queue size. Also sets SQ's CQ_LIMIT
based on configured Tx queue size such that HW doesn't process
SQEs when there is no sufficient space in CQ.
David S. Miller [Wed, 25 Jan 2017 19:40:25 +0000 (14:40 -0500)]
Merge branch 'phy-truncated-led-names'
Geert Uytterhoeven says:
====================
net: phy: leds: Fix truncated LED trigger names and crashes
I started seeing crashes during s2ram and poweroff on all my ARM boards,
like:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[<c04116d4>] (__list_del_entry_valid) from [<c05e8948>] (led_trigger_unregister+0x34/0xcc)
[<c05e8948>] (led_trigger_unregister) from [<c05336c4>] (phy_led_triggers_unregister+0x28/0x34)
[<c05336c4>] (phy_led_triggers_unregister) from [<c0531d44>] (phy_detach+0x30/0x74)
[<c0531d44>] (phy_detach) from [<c0538bdc>] (sh_eth_close+0x64/0x9c)
[<c0538bdc>] (sh_eth_close) from [<c04d4ce0>] (dpm_run_callback+0x48/0xc8)
or:
list_del corruption. prev->next should be dede6540, but was 2e323931
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:52!
...
[<c02f6d70>] (__list_del_entry_valid) from [<c0425168>] (led_trigger_unregister+0x34/0xcc)
[<c0425168>] (led_trigger_unregister) from [<c03a05a0>] (phy_led_triggers_unregister+0x28/0x34)
[<c03a05a0>] (phy_led_triggers_unregister) from [<c039ec04>] (phy_detach+0x30/0x74)
[<c039ec04>] (phy_detach) from [<c03a4fc0>] (sh_eth_close+0x6c/0xa4)
[<c03a4fc0>] (sh_eth_close) from [<c0483234>] (__dev_close_many+0xac/0xd0)
As the only clue was a kernel message like
sh-eth ee700000.ethernet eth0: No phy led trigger registered for speed(100)
I had to bisected this, leading to commit 4567d686f5c6d955 ("phy:
increase size of MII_BUS_ID_SIZE and bus_id"). Reverting that commit
fixed the issue.
More investigation revealed the crashes are due to the combination of
two things:
- Truncated LED trigger names, leading to duplicate names, and
registration failures,
- Bad error handling in case of registration failures.
Both are fixed by this patch series.
Changes compared to v1:
- Add Reviewed-by,
- New patch "net: phy: leds: Break dependency of phy.h on
phy_led_triggers.h",
- Drop moving the include of <linux/phy_led_triggers.h>, as
<linux/phy.h> no longer includes it,
- #include <linux/phy.h> from <linux/phy_led_triggers.h>.
====================
Commit 4567d686f5c6d955 ("phy: increase size of MII_BUS_ID_SIZE and
bus_id") increased the size of MII bus IDs, but forgot to update the
private definition in <linux/phy_led_triggers.h>.
This may cause:
1. Truncation of LED trigger names,
2. Duplicate LED trigger names,
3. Failures registering LED triggers,
4. Crashes due to bad error handling in the LED trigger failure path.
To fix this, and prevent the definitions going out of sync again in the
future, let the PHY LED trigger code use the existing MII_BUS_ID_SIZE
definition.
Example:
- Before I had triggers "ee700000.etherne:01:100Mbps" and
"ee700000.etherne:01:10Mbps",
- After the increase of MII_BUS_ID_SIZE, both became
"ee700000.ethernet-ffffffff:01:" => FAIL,
- Now, the triggers are "ee700000.ethernet-ffffffff:01:100Mbps" and
"ee700000.ethernet-ffffffff:01:10Mbps", which are unique again.
Fixes: 4567d686f5c6d955 ("phy: increase size of MII_BUS_ID_SIZE and bus_id") Fixes: 2e0bc452f4721520 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Geert Uytterhoeven <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: phy: leds: Break dependency of phy.h on phy_led_triggers.h
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
net: phy: leds: Clear phy_num_led_triggers on failure to avoid crash
phy_attach_direct() ignores errors returned by
phy_led_triggers_register(). I think that's OK, as LED triggers can be
considered a non-critical feature.
However, this causes problems later:
- phy_led_trigger_change_speed() will access the array
phy_device.phy_led_triggers, which has been freed in the error path
of phy_led_triggers_register(), which may lead to a crash.
- phy_led_triggers_unregister() will access the same array, leading to
crashes during s2ram or poweroff, like:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[<c04116d4>] (__list_del_entry_valid) from [<c05e8948>] (led_trigger_unregister+0x34/0xcc)
[<c05e8948>] (led_trigger_unregister) from [<c05336c4>] (phy_led_triggers_unregister+0x28/0x34)
[<c05336c4>] (phy_led_triggers_unregister) from [<c0531d44>] (phy_detach+0x30/0x74)
[<c0531d44>] (phy_detach) from [<c0538bdc>] (sh_eth_close+0x64/0x9c)
[<c0538bdc>] (sh_eth_close) from [<c04d4ce0>] (dpm_run_callback+0x48/0xc8)
or:
list_del corruption. prev->next should be dede6540, but was 2e323931
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:52!
...
[<c02f6d70>] (__list_del_entry_valid) from [<c0425168>] (led_trigger_unregister+0x34/0xcc)
[<c0425168>] (led_trigger_unregister) from [<c03a05a0>] (phy_led_triggers_unregister+0x28/0x34)
[<c03a05a0>] (phy_led_triggers_unregister) from [<c039ec04>] (phy_detach+0x30/0x74)
[<c039ec04>] (phy_detach) from [<c03a4fc0>] (sh_eth_close+0x6c/0xa4)
[<c03a4fc0>] (sh_eth_close) from [<c0483234>] (__dev_close_many+0xac/0xd0)
To fix this, clear phy_device.phy_num_led_triggers in the error path of
phy_led_triggers_register() fails.
Note that the "No phy led trigger registered for speed" message will
still be printed on link speed changes, which is a good cue that
something went wrong with the LED triggers.
Fixes: 2e0bc452f4721520 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Geert Uytterhoeven <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
John Crispin [Wed, 25 Jan 2017 08:20:55 +0000 (09:20 +0100)]
net-next: ethernet: mediatek: change the compatible string
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
John Crispin [Wed, 25 Jan 2017 08:20:54 +0000 (09:20 +0100)]
Documentation: devicetree: change the mediatek ethernet compatible string
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Willy Tarreau [Wed, 25 Jan 2017 13:42:46 +0000 (14:42 +0100)]
net/tcp-fastopen: make connect()'s return case more consistent with non-TFO
Without TFO, any subsequent connect() call after a successful one returns
-1 EISCONN. The last API update ensured that __inet_stream_connect() can
return -1 EINPROGRESS in response to sendmsg() when TFO is in use to
indicate that the connection is now in progress. Unfortunately since this
function is used both for connect() and sendmsg(), it has the undesired
side effect of making connect() now return -1 EINPROGRESS as well after
a successful call, while at the same time poll() returns POLLOUT. This
can confuse some applications which happen to call connect() and to
check for -1 EISCONN to ensure the connection is usable, and for which
EINPROGRESS indicates a need to poll, causing a loop.
This problem was encountered in haproxy where a call to connect() is
precisely used in certain cases to confirm a connection's readiness.
While arguably haproxy's behaviour should be improved here, it seems
important to aim at a more robust behaviour when the goal of the new
API is to make it easier to implement TFO in existing applications.
This patch simply ensures that we preserve the same semantics as in
the non-TFO case on the connect() syscall when using TFO, while still
returning -1 EINPROGRESS on sendmsg(). For this we simply tell
__inet_stream_connect() whether we're doing a regular connect() or in
fact connecting for a sendmsg() call.
David S. Miller [Wed, 25 Jan 2017 19:04:39 +0000 (14:04 -0500)]
Merge branch 'tcp-fastopen-new-API'
Wei Wang says:
====================
net/tcp-fastopen: Add new userspace API support
The patch series is to add support for new userspace API for TCP fastopen
sockets.
In the current code, user has to call sendto()/sendmsg() with special flag
MSG_FASTOPEN for TCP fastopen sockets. This API is quite different from the
normal TCP socket API and can be cumbersome for applications to make use
fastopen sockets.
So this new patch introduces a new way of using TCP fastopen sockets which
is similar to normal TCP sockets with a new sockopt TCP_FASTOPEN_CONNECT.
More details about it is described in the third patch.
(First 2 patches are preparations for the third patch.)
====================
Wei Wang [Mon, 23 Jan 2017 18:59:22 +0000 (10:59 -0800)]
net/tcp-fastopen: Add new API support
This patch adds a new socket option, TCP_FASTOPEN_CONNECT, as an
alternative way to perform Fast Open on the active side (client). Prior
to this patch, a client needs to replace the connect() call with
sendto(MSG_FASTOPEN). This can be cumbersome for applications who want
to use Fast Open: these socket operations are often done in lower layer
libraries used by many other applications. Changing these libraries
and/or the socket call sequences are not trivial. A more convenient
approach is to perform Fast Open by simply enabling a socket option when
the socket is created w/o changing other socket calls sequence:
s = socket()
create a new socket
setsockopt(s, IPPROTO_TCP, TCP_FASTOPEN_CONNECT …);
newly introduced sockopt
If set, new functionality described below will be used.
Return ENOTSUPP if TFO is not supported or not enabled in the
kernel.
connect()
With cookie present, return 0 immediately.
With no cookie, initiate 3WHS with TFO cookie-request option and
return -1 with errno = EINPROGRESS.
write()/sendmsg()
With cookie present, send out SYN with data and return the number of
bytes buffered.
With no cookie, and 3WHS not yet completed, return -1 with errno =
EINPROGRESS.
No MSG_FASTOPEN flag is needed.
read()
Return -1 with errno = EWOULDBLOCK/EAGAIN if connect() is called but
write() is not called yet.
Return -1 with errno = EWOULDBLOCK/EAGAIN if connection is
established but no msg is received yet.
Return number of bytes read if socket is established and there is
msg received.
The new API simplifies life for applications that always perform a write()
immediately after a successful connect(). Such applications can now take
advantage of Fast Open by merely making one new setsockopt() call at the time
of creating the socket. Nothing else about the application's socket call
sequence needs to change.
Wei Wang [Mon, 23 Jan 2017 18:59:21 +0000 (10:59 -0800)]
net: Remove __sk_dst_reset() in tcp_v6_connect()
Remove __sk_dst_reset() in the failure handling because __sk_dst_reset()
will eventually get called when sk is released. No need to handle it in
the protocol specific connect call.
This is also to make the code path consistent with ipv4.
David S. Miller [Wed, 25 Jan 2017 18:27:14 +0000 (13:27 -0500)]
Merge branch 'bnxt_en-rtnl-fixes'
Michael Chan says:
====================
bnxt_en: Fix RTNL lock usage in bnxt_sp_task().
There are 2 function calls from bnxt_sp_task() that have buggy RTNL
usage. These 2 functions take RTNL lock under some conditions, but
some callers (such as open, ethtool) have already taken RTNL. These
3 patches fix the issue by making it clear that callers must take
RTNL. If the caller is bnxt_sp_task() which does not automatically
take RTNL, we add a common scheme for bnxt_sp_task() to call these
functions properly under RTNL.
====================
Michael Chan [Wed, 25 Jan 2017 07:55:09 +0000 (02:55 -0500)]
bnxt_en: Fix RTNL lock usage on bnxt_get_port_module_status().
bnxt_get_port_module_status() calls bnxt_update_link() which expects
RTNL to be held. In bnxt_sp_task() that does not hold RTNL, we need to
call it with a prior call to bnxt_rtnl_lock_sp() and the call needs to
be moved to the end of bnxt_sp_task().
Michael Chan [Wed, 25 Jan 2017 07:55:08 +0000 (02:55 -0500)]
bnxt_en: Fix RTNL lock usage on bnxt_update_link().
bnxt_update_link() is called from multiple code paths. Most callers,
such as open, ethtool, already hold RTNL. Only the caller bnxt_sp_task()
does not. So it is a bug to take RTNL inside bnxt_update_link().
Fix it by removing the RTNL inside bnxt_update_link(). The function
now expects the caller to always hold RTNL.
In bnxt_sp_task(), call bnxt_rtnl_lock_sp() before calling
bnxt_update_link(). We also need to move the call to the end of
bnxt_sp_task() since it will be clearing the BNXT_STATE_IN_SP_TASK bit.
Michael Chan [Wed, 25 Jan 2017 07:55:07 +0000 (02:55 -0500)]
bnxt_en: Fix bnxt_reset() in the slow path task.
In bnxt_sp_task(), we set a bit BNXT_STATE_IN_SP_TASK so that bnxt_close()
will synchronize and wait for bnxt_sp_task() to finish. Some functions
in bnxt_sp_task() require us to clear BNXT_STATE_IN_SP_TASK and then
acquire rtnl_lock() to prevent race conditions.
There are some bugs related to this logic. This patch refactors the code
to have common bnxt_rtnl_lock_sp() and bnxt_rtnl_unlock_sp() to handle
the RTNL and the clearing/setting of the bit. Multiple functions will
need the same logic. We also need to move bnxt_reset() to the end of
bnxt_sp_task(). Functions that clear BNXT_STATE_IN_SP_TASK must be the
last functions to be called in bnxt_sp_task(). The common scheme will
handle the condition properly.
Linus Torvalds [Wed, 25 Jan 2017 18:25:36 +0000 (10:25 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio/vhost fixes from Michael Tsirkin:
- ARM DMA fixes
- vhost vsock bugfix
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vring: Force use of DMA API for ARM-based systems with legacy devices
virtio_mmio: Set DMA masks appropriately
vhost/vsock: handle vhost_vq_init_access() error
David S. Miller [Wed, 25 Jan 2017 18:17:48 +0000 (13:17 -0500)]
Merge branch 'bpf-tracepoints'
Daniel Borkmann says:
====================
BPF tracepoints
This set adds tracepoints to BPF for better introspection and
debugging. The first two patches are prerequisite for the actual
third patch that adds the tracepoints. I think the first two are
small and straight forward enough that they could ideally go via
net-next, but I'm also open to other suggestions on how to route
them in case that's not applicable (it would reduce potential
merge conflicts on BPF side, though). For details, please see
individual patches.
====================
Daniel Borkmann [Wed, 25 Jan 2017 01:28:18 +0000 (02:28 +0100)]
bpf: add initial bpf tracepoints
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
projects / linux.git / log