Paulo Alcantara [Tue, 28 Feb 2023 22:01:54 +0000 (19:01 -0300)]
cifs: improve checking of DFS links over STATUS_OBJECT_NAME_INVALID
Do not map STATUS_OBJECT_NAME_INVALID to -EREMOTE under non-DFS
shares, or 'nodfs' mounts or CONFIG_CIFS_DFS_UPCALL=n builds.
Otherwise, in the slow path, get a referral to figure out whether it
is an actual DFS link.
This could be simply reproduced under a non-DFS share by running the
following
David Howells [Mon, 27 Feb 2023 13:04:54 +0000 (13:04 +0000)]
iov: Fix netfs_extract_user_to_sg()
Fix the loop check in netfs_extract_user_to_sg() for extraction from
user-backed iterators to do the body if npages > 0, not if npages < 0
(which it can never be).
This isn't currently used by cifs, which only ever extracts data from BVEC,
KVEC and XARRAY iterators at this level, user-backed iterators having being
decanted into BVEC iterators at a higher level to accommodate the work
being done in a kernel thread.
Found by smatch:
fs/netfs/iterator.c:139 netfs_extract_user_to_sg() warn: unsigned 'npages' is never less than zero.
David Howells [Mon, 27 Feb 2023 13:04:53 +0000 (13:04 +0000)]
cifs: Fix cifs_write_back_from_locked_folio()
cifs_write_back_from_locked_folio() should return the number of bytes read,
but returns the result of ->async_writev(), which will be 0 on success. As
it happens, this doesn't prevent cifs_writepages_region() from working as
it will then examine and ignore the pages that are no longer dirty rather
than just skipping over them.
Shyam Prasad N [Tue, 27 Dec 2022 14:04:29 +0000 (14:04 +0000)]
cifs: match even the scope id for ipv6 addresses
match_address function matches the scope id for ipv6 addresses,
but cifs_match_ipaddr (which is another function used for comparison)
does not use scope id. Doing so with this change.
Applications need to be able to program the SBI implementation specific
or custom firmware events in addition to the standard firmware events.
Remove a check in the driver that prohibits the programming of the custom
firmware events.
Linus Torvalds [Wed, 1 Mar 2023 19:03:44 +0000 (11:03 -0800)]
Merge tag 'nfsd-6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- Make new GSS Kerberos Kunit tests work on non-x86 platforms
* tag 'nfsd-6.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
SUNRPC: Properly terminate test case arrays
SUNRPC: Let Kunit tests run with some enctypes compiled out
Gerald Schaefer [Mon, 27 Feb 2023 19:03:00 +0000 (20:03 +0100)]
s390/extmem: return correct segment type in __segment_load()
Commit f05f62d04271f ("s390/vmem: get rid of memory segment list")
reshuffled the call to vmem_add_mapping() in __segment_load(), which now
overwrites rc after it was set to contain the segment type code.
As result, __segment_load() will now always return 0 on success, which
corresponds to the segment type code SEG_TYPE_SW, i.e. a writeable
segment. This results in a kernel crash when loading a read-only segment
as dcssblk block device, and trying to write to it.
Instead of reshuffling code again, make sure to return the segment type
on success, and also describe this rather delicate and unexpected logic
in the function comment. Also initialize new segtype variable with
invalid value, to prevent possible future confusion.
Dan Carpenter [Mon, 27 Feb 2023 10:07:09 +0000 (13:07 +0300)]
cpufreq: apple-soc: Fix an IS_ERR() vs NULL check
The of_iomap() function returns NULL if it fails. It never returns
error pointers. Fix the check accordingly.
Fixes: 6286bbb40576 ("cpufreq: apple-soc: Add new driver to control Apple SoC CPU P-states") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Eric Curtin <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
Randy Dunlap [Sun, 26 Feb 2023 05:39:52 +0000 (21:39 -0800)]
thermal: intel: BXT_PMIC: select REGMAP instead of depending on it
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: b474303ffd57 ("thermal: add Intel BXT WhiskeyCove PMIC thermal driver") Signed-off-by: Randy Dunlap <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
ACPI: x86: utils: Add Cezanne to the list for forcing StorageD3Enable
commit 018d6711c26e4 ("ACPI: x86: Add a quirk for Dell Inspiron 14 2-in-1
for StorageD3Enable") introduced a quirk to allow a system with ambiguous
use of _ADR 0 to force StorageD3Enable.
It was reported that several more Dell systems suffered the same symptoms.
As the list is continuing to grow but these are all Cezanne systems,
instead add Cezanne to the CPU list to apply the StorageD3Enable property
and remove the whole list.
It was also reported that an HP system only has StorageD3Enable on the ACPI
device for the first NVME disk, not the second.
Linus Torvalds [Tue, 28 Feb 2023 19:39:09 +0000 (11:39 -0800)]
capability: just use a 'u64' instead of a 'u32[2]' array
Back in 2008 we extended the capability bits from 32 to 64, and we did
it by extending the single 32-bit capability word from one word to an
array of two words. It was then obfuscated by hiding the "2" behind two
macro expansions, with the reasoning being that maybe it gets extended
further some day.
That reasoning may have been valid at the time, but the last thing we
want to do is to extend the capability set any more. And the array of
values not only causes source code oddities (with loops to deal with
it), but also results in worse code generation. It's a lose-lose
situation.
So just change the 'u32[2]' into a 'u64' and be done with it.
We still have to deal with the fact that the user space interface is
designed around an array of these 32-bit values, but that was the case
before too, since the array layouts were different (ie user space
doesn't use an array of 32-bit values for individual capability masks,
but an array of 32-bit slices of multiple masks).
So that marshalling of data is actually simplified too, even if it does
remain somewhat obscure and odd.
This was all triggered by my reaction to the new "cap_isidentical()"
introduced recently. By just using a saner data structure, it went from
Linus Torvalds [Wed, 1 Mar 2023 17:44:22 +0000 (09:44 -0800)]
Merge tag 'sh-for-v6.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
- regression fix in connection with the rtl8169 driver on SuperH boards
that was introduced when the driver was switched to use
devm_clk_get_optional_enabled() to simplify the code (Geert
Uytterhoeven)
- build warning fix to allow the kernel to be built with CONFIG_WERROR
enabled (Michael Karcher)
* tag 'sh-for-v6.3-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: clk: Fix clk_enable() to return 0 on NULL clk
sh: intc: Avoid spurious sizeof-pointer-div warning
Linus Torvalds [Wed, 1 Mar 2023 17:27:00 +0000 (09:27 -0800)]
Merge tag 'loongarch-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Make -mstrict-align configurable
- Add kernel relocation and KASLR support
- Add single kernel image implementation for kdump
- Add hardware breakpoints/watchpoints support
- Add kprobes/kretprobes/kprobes_on_ftrace support
- Add LoongArch support for some selftests.
* tag 'loongarch-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: (23 commits)
selftests/ftrace: Add LoongArch kprobe args string tests support
selftests/seccomp: Add LoongArch selftesting support
tools: Add LoongArch build infrastructure
samples/kprobes: Add LoongArch support
LoongArch: Mark some assembler symbols as non-kprobe-able
LoongArch: Add kprobes on ftrace support
LoongArch: Add kretprobes support
LoongArch: Add kprobes support
LoongArch: Simulate branch and PC* instructions
LoongArch: ptrace: Add hardware single step support
LoongArch: ptrace: Add function argument access API
LoongArch: ptrace: Expose hardware breakpoints to debuggers
LoongArch: Add hardware breakpoints/watchpoints support
LoongArch: kdump: Add crashkernel=YM handling
LoongArch: kdump: Add single kernel image implementation
LoongArch: Add support for kernel address space layout randomization (KASLR)
LoongArch: Add support for kernel relocation
LoongArch: Add la_abs macro implementation
LoongArch: Add JUMP_VIRT_ADDR macro implementation to avoid using la.abs
LoongArch: Use la.pcrel instead of la.abs when it's trivially possible
...
Linus Torvalds [Wed, 1 Mar 2023 17:13:00 +0000 (09:13 -0800)]
Merge tag 'uml-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux
Pull UML updates from Richard Weinberger:
- Add support for rust (yay!)
- Add support for LTO
- Add platform bus support to virtio-pci
- Various virtio fixes
- Coding style, spelling cleanups
* tag 'uml-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/uml/linux: (27 commits)
Documentation: rust: Fix arch support table
uml: vector: Remove unused definitions VECTOR_{WRITE,HEADERS}
um: virt-pci: properly remove PCI device from bus
um: virtio_uml: move device breaking into workqueue
um: virtio_uml: mark device as unregistered when breaking it
um: virtio_uml: free command if adding to virtqueue failed
UML: define RUNTIME_DISCARD_EXIT
virt-pci: add platform bus support
um-virt-pci: Make max delay configurable
um: virt-pci: implement pcibios_get_phb_of_node()
um: Support LTO
um: put power options in a menu
um: Use CFLAGS_vmlinux
um: Prevent building modules incompatible with MODVERSIONS
um: Avoid pcap multiple definition errors
um: Make the definition of cpu_data more compatible
x86: um: vdso: Add '%rcx' and '%r11' to the syscall clobber list
rust: arch/um: Add support for CONFIG_RUST under x86_64 UML
rust: arch/um: Disable FP/SIMD instruction to match x86
rust: arch/um: Use 'pie' relocation mode under UML
...
Linus Torvalds [Wed, 1 Mar 2023 17:06:51 +0000 (09:06 -0800)]
Merge tag 'ubifs-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull jffs2, ubi and ubifs updates from Richard Weinberger:
"JFFS2:
- Fix memory corruption in error path
- Spelling and coding style fixes
UBI:
- Switch to BLK_MQ_F_BLOCKING in ubiblock
- Wire up partent device (for sysfs)
- Multiple UAF bugfixes
- Fix for an infinite loop in WL error path
UBIFS:
- Fix for multiple memory leaks in error paths
- Fixes for wrong space accounting
- Minor cleanups
- Spelling and coding style fixes"
* tag 'ubifs-for-linus-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs: (36 commits)
ubi: block: Fix a possible use-after-free bug in ubiblock_create()
ubifs: make kobj_type structures constant
mtd: ubi: block: wire-up device parent
mtd: ubi: wire-up parent MTD device
ubi: use correct names in function kernel-doc comments
ubi: block: set BLK_MQ_F_BLOCKING
jffs2: Fix list_del corruption if compressors initialized failed
jffs2: Use function instead of macro when initialize compressors
jffs2: fix spelling mistake "neccecary"->"necessary"
ubifs: Fix kernel-doc
ubifs: Fix some kernel-doc comments
UBI: Fastmap: Fix kernel-doc
ubi: ubi_wl_put_peb: Fix infinite loop when wear-leveling work failed
ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
ubi: fastmap: Fix missed fm_anchor PEB in wear-leveling after disabling fastmap
ubifs: ubifs_releasepage: Remove ubifs_assert(0) to valid this process
ubifs: ubifs_writepage: Mark page dirty after writing inode failed
ubifs: dirty_cow_znode: Fix memleak in error handling path
ubifs: Re-statistic cleaned znode count if commit failed
ubi: Fix permission display of the debugfs files
...
Linus Torvalds [Wed, 1 Mar 2023 16:52:49 +0000 (08:52 -0800)]
Merge tag '9p-6.3-for-linus-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p updates from Eric Van Hensbergen:
- some fixes and cleanup setting up for a larger set of performance
patches I've been working on
- a contributed fixes relating to 9p/rdma
- some contributed fixes relating to 9p/xen
* tag '9p-6.3-for-linus-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: fix error reporting in v9fs_dir_release
net/9p: fix bug in client create for .L
9p/rdma: unmap receive dma buffer in rdma_request()/post_recv()
9p/xen: fix connection sequence
9p/xen: fix version parsing
fs/9p: Expand setup of writeback cache to all levels
net/9p: Adjust maximum MSIZE to account for p9 header
Linus Torvalds [Wed, 1 Mar 2023 16:42:27 +0000 (08:42 -0800)]
Merge tag 'exfat-for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat
Pull exfat updates from Namjae Jeon:
- Handle vendor extension and allocation entries as unrecognized benign
secondary entries
- Fix wrong ->i_blocks on devices with non-512 byte sector
- Add the check to avoid returning -EIO from exfat_readdir() at current
position exceeding the directory size
- Fix a bug that reach the end of the directory stream at a position
not aligned with the dentry size
- Redefine DIR_DELETED as 0xFFFFFFF7, the bad cluster number
- Two cleanup fixes and fix cluster leakage in error handling
* tag 'exfat-for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
exfat: fix the newly allocated clusters are not freed in error handling
exfat: don't print error log in normal case
exfat: remove unneeded code from exfat_alloc_cluster()
exfat: handle unreconized benign secondary entries
exfat: fix inode->i_blocks for non-512 byte sector size device
exfat: redefine DIR_DELETED as the bad cluster number
exfat: fix reporting fs error when reading dir beyond EOF
exfat: fix unexpected EOF while reading dir
Jens Axboe [Wed, 1 Mar 2023 14:49:59 +0000 (07:49 -0700)]
Merge tag 'nvme-6.3-2022-03-01' of git://git.infradead.org/nvme into for-6.3/block
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 6.3
- don't access released socket during error recovery (Akinobu Mita)
- bring back auto-removal of deleted namespaces during sequential scan
(Christoph Hellwig)
- fix an error code in nvme_auth_process_dhchap_challenge
(Dan Carpenter)
- show well known discovery name (Daniel Wagner)
- add a missing endianess conversion in effects masking (Keith Busch)"
* tag 'nvme-6.3-2022-03-01' of git://git.infradead.org/nvme:
nvme-fabrics: show well known discovery name
nvme-tcp: don't access released socket during error recovery
nvme-auth: fix an error code in nvme_auth_process_dhchap_challenge()
nvme: bring back auto-removal of deleted namespaces during sequential scan
nvme: fix sparse warning on effects masking
In etdm dai driver, dai_etdm_parse_of() function is used to parse dts
properties to get parameters. There are two for-loops which are
sepearately for all etdm and etdm input only cases. In etdm in only
loop, dai_id is not initialized, so it keeps the value intiliazed in
another loop.
In the patch, add the missing initialization to fix the unexpected
parsing problem.
In etdm dai driver, dai_etdm_parse_of() function is used to parse dts
properties to get parameters. There are two for-loops which are
sepearately for all etdm and etdm input only cases. In etdm in only
loop, dai_id is not initialized, so it keeps the value intiliazed in
another loop.
In the patch, add the missing initialization to fix the unexpected
parsing problem.
Tom Lendacky [Wed, 22 Feb 2023 16:39:39 +0000 (10:39 -0600)]
virt/sev-guest: Return -EIO if certificate buffer is not large enough
Commit
47894e0fa6a5 ("virt/sev-guest: Prevent IV reuse in the SNP guest driver")
changed the behavior associated with the return value when the caller
does not supply a large enough certificate buffer. Prior to the commit a
value of -EIO was returned. Now, 0 is returned. This breaks the
established ABI with the user.
Change the code to detect the buffer size error and return -EIO.
Björn Töpel [Tue, 28 Feb 2023 18:42:10 +0000 (19:42 +0100)]
riscv, lib: Fix Zbb strncmp
The Zbb optimized strncmp has two parts; a fast path that does XLEN/8B
per iteration, and a slow that does one byte per iteration.
The idea is to compare aligned XLEN chunks for most of strings, and do
the remainder tail in the slow path.
The Zbb strncmp has two issues in the fast path:
Incorrect remainder handling (wrong compare): Assume that the string
length is 9. On 64b systems, the fast path should do one iteration,
and one iteration in the slow path. Instead, both were done in the
fast path, which lead to incorrect results. An example:
strncmp("/dev/vda", "/dev/", 5);
Correct by changing "bgt" to "bge".
Missing NULL checks in the second string: This could lead to incorrect
results for:
Linus Torvalds [Wed, 1 Mar 2023 00:08:30 +0000 (16:08 -0800)]
Merge tag 'xfs-6.3-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull moar xfs updates from Darrick Wong:
"This contains a fix for a deadlock in the allocator. It continues the
slow march towards being able to offline AGs, and it refactors the
interface to the xfs allocator to be less indirection happy.
Summary:
- Fix a deadlock in the free space allocator due to the AG-walking
algorithm forgetting to follow AG-order locking rules
- Make the inode allocator prefer existing free inodes instead of
failing to allocate new inode chunks when free space is low
- Set minleft correctly when setting allocator parameters for bmap
changes
- Fix uninitialized variable access in the getfsmap code
- Make a distinction between active and passive per-AG structure
references. For now, active references are taken to perform some
work in an AG on behalf of a high level operation; passive
references are used by lower level code to finish operations
started by other threads. Eventually this will become part of
online shrink
- Split out all the different allocator strategies into separate
functions to move us away from design antipattern of filling out a
huge structure for various differentish things and issuing a single
function multiplexing call
- Various cleanups in the filestreams allocator code, which we might
very well want to deprecate instead of continuing
- Fix a bug with the agi rotor code that was introduced earlier in
this series"
* tag 'xfs-6.3-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (44 commits)
xfs: restore old agirotor behavior
xfs: fix uninitialized variable access
xfs: refactor the filestreams allocator pick functions
xfs: return a referenced perag from filestreams allocator
xfs: pass perag to filestreams tracing
xfs: use for_each_perag_wrap in xfs_filestream_pick_ag
xfs: track an active perag reference in filestreams
xfs: factor out MRU hit case in xfs_filestream_select_ag
xfs: remove xfs_filestream_select_ag() longest extent check
xfs: merge new filestream AG selection into xfs_filestream_select_ag()
xfs: merge filestream AG lookup into xfs_filestream_select_ag()
xfs: move xfs_bmap_btalloc_filestreams() to xfs_filestreams.c
xfs: use xfs_bmap_longest_free_extent() in filestreams
xfs: get rid of notinit from xfs_bmap_longest_free_extent
xfs: factor out filestreams from xfs_bmap_btalloc_nullfb
xfs: convert trim to use for_each_perag_range
xfs: convert xfs_alloc_vextent_iterate_ags() to use perag walker
xfs: move the minimum agno checks into xfs_alloc_vextent_check_args
xfs: fold xfs_alloc_ag_vextent() into callers
xfs: move allocation accounting to xfs_alloc_vextent_set_fsbno()
...
* tag 'i3c/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: stop hardcoding initial speed
i3c: transfer pid from boardinfo to device info
Linus Torvalds [Wed, 1 Mar 2023 00:01:08 +0000 (16:01 -0800)]
Merge tag 'docs-6.3-2' of git://git.lwn.net/linux
Pull Documentation stragglers from Jonathan Corbet:
"A handful of documentation patches that were ready before the merge
window, but which I didn't get merged for the first round:
- A recommendation from Thorsten (also akpm) on use of Link tags to
point out problem reports
- Some front-page formatting tweaks
- Another Spanish translation
- One typo(ish) fix"
* tag 'docs-6.3-2' of git://git.lwn.net/linux:
docs: recommend using Link: whenever using Reported-by:
Documentation: front page: use recommended heading adornments
docs/sp_SP: Add process programming-language translation
docs: locking: refer to the actual existing config names
Jack Chen [Thu, 16 Feb 2023 15:10:57 +0000 (10:10 -0500)]
i3c: master: dw: stop hardcoding initial speed
Bus-speed could be default(12.5MHz) or defined by users in dts.
Dw-i3c-master should not hard-code the initial speed to be
I3C_BUS_TYP_I3C_SCL_RATE (12.5MHz)
And because of Synopsys's I3C controller limit (hcnt/lcnt register
length) and core-clk provided, there is a limit to bus speed, too.
For example, when core-clk is 250 MHz, the bus speed cannot be
lowered below 1MHz.
Tested: tested with an i3c sensor and captured with a logic analyzer.
Jiaxun Yang [Tue, 28 Feb 2023 19:34:59 +0000 (19:34 +0000)]
MIPS: Workaround clang inline compat branch issue
Clang is unable to handle the situation that a chunk of inline
assembly ends with a compat branch instruction and then compiler
generates another control transfer instruction immediately after
this compat branch. The later instruction will end up in forbidden
slot and cause exception.
Workaround by add a option to control the use of compact branch.
Currently it's selected by CC_IS_CLANG and hopefully we can change
it to a version check in future if clang manages to fix it.
mips: dts: ralink: mt7621: add phandle to system controller node for watchdog
To allow to access system controller registers from watchdog driver code
add a phandle in the watchdog 'wdt' node. This avoid using arch dependent
operations in driver code.
Nick Alcock [Tue, 28 Feb 2023 13:02:01 +0000 (13:02 +0000)]
powercap: remove MODULE_LICENSE in non-modules
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Nick Alcock [Fri, 24 Feb 2023 15:07:49 +0000 (15:07 +0000)]
cpufreq: intel_pstate: remove MODULE_LICENSE in non-modules
Since commit 8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
This is a collection of fixes I came up after glancing through an
initial test run with the snappily named Kukui Jacuzzi SKU16 Chromebook
on KernelCI. There are more issues flagged, this is just what I fixed
thus far.
To start capture on Microchip PDMC the enable bits for each supported
microphone need to be set. After this bit is set the PDMC starts to
receive data from microphones and it considers this data as valid data.
Thus if microphones are not ready the PDMC captures anyway data from its
lines. This data is interpreted by the human ear as poc noises.
To avoid this the following software workaround need to be applied when
starting capture:
1/ enable PDMC channel
2/ wait 150ms
3/ execute 16 dummy reads from RHR
4/ clear interrupts
5/ enable interrupts
6/ enable DMA channel
For this workaround to work step 6 need to be executed at the end.
For step 6 was added patch 1/3 from this series. With this, component
DAI driver sets its struct snd_soc_component_driver::start_dma_last = 1
and proper action is taken based on this flag when starting DAI trigger
vs DMA.
This is a collection of fixes I came up after glancing through an
initial test run with the snappily named Kukui Jacuzzi SKU16 Chromebook
on KernelCI. There are more issues flagged, this is just what I fixed
thus far.
This is a collection of fixes I came up after glancing through an
initial test run with the Spherion Chromebook on KernelCI. There are
more issues flagged, this is just what I fixed thus far - the volume
controls on the MT6359 have issues for example, and a lot of controls
aren't marked as Switches like they should be.
Linus Torvalds [Tue, 28 Feb 2023 17:12:47 +0000 (09:12 -0800)]
Merge tag 'pwm/for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This rather small set of changes includes some minor fixes and
improvements.
The AB8500 driver gained support for reading the initial hardware
state and the Synopsys DesignWare driver received some work to prepare
for device tree and platform support"
* tag 'pwm/for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: dwc: Use devm_pwmchip_add()
pwm: dwc: Move memory allocation to own function
pwm: dwc: Change &pci->dev to dev in probe
dt-bindings: pwm: Document Synopsys DesignWare snps,pwm-dw-apb-timers-pwm2
pwm: iqs620a: Replace one remaining instance of regmap_update_bits()
pwm: ab8500: Implement .get_state()
pwm: ab8500: Fix calculation of duty and period
pwm: lp3943: Drop unused i2c include
dt-bindings: pwm: mediatek: Convert pwm-mediatek to DT schema
pwm: stm32-lp: fix the check on arr and cmp registers update
pwm: Move pwm_capture() dummy to restore order
pwm: sifive: Always let the first pwm_apply_state succeed
Linus Torvalds [Tue, 28 Feb 2023 17:05:47 +0000 (09:05 -0800)]
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Improve performance for ext4 by allowing multiple process to perform
direct I/O writes to preallocated blocks by using a shared inode lock
instead of taking an exclusive lock.
In addition, multiple bug fixes and cleanups"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix incorrect options show of original mount_opt and extend mount_opt2
ext4: Fix possible corruption when moving a directory
ext4: init error handle resource before init group descriptors
ext4: fix task hung in ext4_xattr_delete_inode
jbd2: fix data missing when reusing bh which is ready to be checkpointed
ext4: update s_journal_inum if it changes after journal replay
ext4: fail ext4_iget if special inode unallocated
ext4: fix function prototype mismatch for ext4_feat_ktype
ext4: remove unnecessary variable initialization
ext4: fix inode tree inconsistency caused by ENOMEM
ext4: refuse to create ea block when umounted
ext4: optimize ea_inode block expansion
ext4: remove dead code in updating backup sb
ext4: dio take shared inode lock when overwriting preallocated blocks
ext4: don't show commit interval if it is zero
ext4: use ext4_fc_tl_mem in fast-commit replay path
ext4: improve xattr consistency checking and error reporting
Heiko Stuebner [Wed, 8 Feb 2023 22:53:28 +0000 (23:53 +0100)]
RISC-V: improve string-function assembly
Adapt the suggestions for the assembly string functions that Andrew
suggested but that I didn't manage to include into the series that
got applied.
This includes improvements to two comments, removal of unneeded labels
and moving one instruction slightly higher to contradict an
explanatory comment.
Fix warn: iterator used outside loop: 'xfer'. 'xfer' variable contain
invalid value in few conditions. Complete transfer within DATA phase
in successful case and at the end for failed transfer.
Arnd Bergmann [Mon, 27 Feb 2023 08:58:26 +0000 (09:58 +0100)]
ASoC: zl38060 add gpiolib dependency
Without gpiolib, this driver fails to link:
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `chip_gpio_get':
zl38060.c:(.text+0x30): undefined reference to `gpiochip_get_data'
arm-linux-gnueabi-ld: sound/soc/codecs/zl38060.o: in function `zl38_spi_probe':
zl38060.c:(.text+0xa18): undefined reference to `devm_gpiochip_add_data_with_key'
This appears to have been in the driver since the start, but is hard to
hit in randconfig testing since gpiolib is almost always selected by something
else.
Mark Brown [Sat, 25 Feb 2023 21:48:13 +0000 (21:48 +0000)]
ASoC: sam9g20ek: Disable capture unless building with microphone input
Without modification the AT91SAM9G20-EK has no capture support, none of the
inputs of the CODEC are wired to anything to useful and there are no paths
supporting loopback. Since the audio is clocked from the CODEC and the DAPM
inputs are marked as unusable this means that capture will fail to transfer
any data as the ADC path can't be powered up.
Flag this in the device description so apps don't see unusable capture
support, guarded with the existing optional define for mic input.
Mark Brown [Fri, 24 Feb 2023 14:03:58 +0000 (14:03 +0000)]
ASoC: mt8192: Fix range for sidetone positive gain
The Sidetone_Positive_Gain_dB control reports a range of 0..100 as valid
but the put() function rejects anything larger than 24. Fix this.
There are numerous other problems with this control, the name is very non
idiomatic and it should be a TLV, but it's ABI so probably we should leave
those alone.
Mark Brown [Fri, 24 Feb 2023 14:03:55 +0000 (14:03 +0000)]
ASoC: mt8192: Remove spammy log messages
There are a lot of info level log messages in the mt8192 ADDA driver which
are trivially triggerable from userspace, many in normal operation. Remove
these to avoid spamming the console.
Claudiu Beznea [Tue, 28 Feb 2023 11:01:45 +0000 (13:01 +0200)]
ASoC: mchp-pdmc: fix poc noise at capture startup
Microchip PDMC IP doesn't filter microphone noises on startup. By default,
it captures data received from digital microphones after
the MCHP_PDMC_MR.EN bits are set. Thus when enable is set on PDMC side the
digital microphones might not be ready yet and PDMC captures data from then
in this time. This data captured is poc noise. To avoid this the software
workaround is to the following:
1/ enable PDMC channel
2/ wait 150ms (on SAMA7G5-EK setup)
3/ execute 16 dummy reads from RHR
4/ clear interrupts
5/ enable interrupts
6/ enable DMA channel
PDMC can work with different types of microphones, thus different boards
could have different microphones. Depending on microphone type the PDMC
would need to wait longer or shorter period (at startup) than the default
chosen one to filter unwanted noise. Thus add microchip,startup-delay-us
binding to let PDMC users to specify startup delay.
Mark Brown [Sun, 26 Feb 2023 12:49:57 +0000 (12:49 +0000)]
ASoC: mt8183: Fix event generation for I2S DAI operations
ALSA control put() operations should return 0 if the value changed so that
events can be generated appropriately for userspace but the custom control
in the MT8183 I2S DAI driver doesn't do that, fix it.
The HPx Mux enumerations define values 5, 6 and 7 but describe them as
"undefined" and map them to the value 0 on writing. Given the descriptions
and behaviour it seems that these values are invalid and should not be
present in the register, the current behaviour is detected as problematic
by mixer-test:
Mark Brown [Sun, 26 Feb 2023 12:47:57 +0000 (12:47 +0000)]
ASoC: mt6358: Validate Wake on Voice 2 writes
Currently the Wake on Voice 2 control accepts and stores any value written
but it reports that only 0 and 1 are valid values. Reject any out of range
values written by userspace.
Mark Brown [Sun, 26 Feb 2023 12:47:56 +0000 (12:47 +0000)]
ASoC: mt6358: Fix event generation for wake on voice stage 2 switch
ALSA control put() operations should return 0 if the value changed so that
events can be generated appropriately for userspace but the custom control
for wake on voice stage 2 doesn't do this, fix it.
Daniel Wagner [Tue, 21 Feb 2023 16:51:06 +0000 (17:51 +0100)]
nvme-fabrics: show well known discovery name
The kernel always logs the unique subsystem name for a discovery
controller, even in the case user space asked for the well known.
This has lead to confusion as the logs of nvme-cli and the kernel
logs didn't match.
First, nvme-cli connects to the well known discovery controller to
figure out if it supports TP8013. If so then nvme-cli disconnects and
connects to the unique discovery controller. Currently, the kernel show
that user space connected twice to the unique one.
To avoid further confusion, show the well known discovery controller if
user space asked for it:
Akinobu Mita [Sun, 26 Feb 2023 12:42:54 +0000 (21:42 +0900)]
nvme-tcp: don't access released socket during error recovery
While the error recovery work is temporarily failing reconnect attempts,
running the 'nvme list' command causes a kernel NULL pointer dereference
by calling getsockname() with a released socket.
During error recovery work, the nvme tcp socket is released and a new one
created, so it is not safe to access the socket without proper check.
Signed-off-by: Akinobu Mita <[email protected]> Fixes: 02c57a82c008 ("nvme-tcp: print actual source IP address through sysfs "address" attr") Reviewed-by: Martin Belanger <[email protected]> Reviewed-by: Hannes Reinecke <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
Dan Carpenter [Thu, 16 Feb 2023 12:14:49 +0000 (15:14 +0300)]
nvme-auth: fix an error code in nvme_auth_process_dhchap_challenge()
This function was transitioned from returning NVMe status codes to
returning traditional kernel error codes. However, this particular
return now accidentally returns positive error codes like ENOMEM instead
of negative -ENOMEM.
Fixes: b0ef1b11d390 ("nvme-auth: don't use NVMe status codes") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
nvme: bring back auto-removal of deleted namespaces during sequential scan
Bring back the check of the Identify Namespace return value for the
legacy NVMe 1.0-style sequential scanning. While NVMe 1.0 does not
support namespace management, there are "modern" cloud solutions like
Google Cloud Platform that claim the obsolete 1.0 compliance for no
good reason while supporting proprietary sideband namespace management.
Joseph Qi [Tue, 28 Feb 2023 04:54:59 +0000 (12:54 +0800)]
io_uring: fix fget leak when fs don't support nowait buffered read
Heming reported a BUG when using io_uring doing link-cp on ocfs2. [1]
Do the following steps can reproduce this BUG:
mount -t ocfs2 /dev/vdc /mnt/ocfs2
cp testfile /mnt/ocfs2/
./link-cp /mnt/ocfs2/testfile /mnt/ocfs2/testfile.1
umount /mnt/ocfs2
Then umount will fail, and it outputs:
umount: /mnt/ocfs2: target is busy.
While tracing umount, it blames mnt_get_count() not return as expected.
Do a deep investigation for fget()/fput() on related code flow, I've
finally found that fget() leaks since ocfs2 doesn't support nowait
buffered read.
io_issue_sqe
|-io_assign_file // do fget() first
|-io_read
|-io_iter_do_read
|-ocfs2_file_read_iter // return -EOPNOTSUPP
|-kiocb_done
|-io_rw_done
|-__io_complete_rw_common // set REQ_F_REISSUE
|-io_resubmit_prep
|-io_req_prep_async // override req->file, leak happens
This was introduced by commit a196c78b5443 in v5.18. Fix it by don't
re-assign req->file if it has already been assigned.
This happens because ioc_refresh_params() is being called without
a properly initialized ioc->rqos, which is happening later in the callee
side.
ioc_refresh_params() -> ioc_autop_idx() tries to access
ioc->rqos.disk->queue but ioc->rqos.disk is NULL, causing the BUG above.
Create function, called ioc_refresh_params_disk(), that is similar to
ioc_refresh_params() but where the "struct gendisk" could be passed as
an explicit argument. This function will be called when ioc->rqos.disk
is not initialized.
Heiko Carstens [Mon, 27 Feb 2023 17:56:10 +0000 (18:56 +0100)]
s390/smp: perform cpu reset before delegating work to target cpu
Clear CPU state (e.g. all TLB entries, prefetched instructions, etc.)
of the target CPU, however without clearing register contents before
starting any work on it.
This puts the target CPU in a more defined state compared to the
current Stop + Restart sigp orders.
If a machine check interrupt hits while user process is
running __s390_handle_mcck() helper function is called
directly from the interrupt handler and terminates the
current process by calling make_task_dead() routine.
The make_task_dead() is not allowed to be called from
interrupt context which forces the machine check handler
switch to the kernel stack and enable local interrupts
first.
The __s390_handle_mcck() could also be called to service
pending work, but this time from the external interrupts
handler. It is the machine check handler that establishes
the work and schedules the external interrupt, therefore
the machine check interrupt itself should be disabled
while reading out the corresponding variable:
However, local_mcck_disable() does not have effect when
__s390_handle_mcck() is called directly form the machine
check handler, since the machine check interrupt is still
disabled. Therefore, it is not the opening bracket to the
following local_mcck_enable() function.
Simplify the user process termination flow by scheduling
the external interrupt and killing the affected process
from the interrupt context.
Assume a kernel-generated signal is always delivered and
ignore a value returned by do_send_sig_info() funciton.
Heiko Carstens [Fri, 24 Feb 2023 10:02:37 +0000 (11:02 +0100)]
s390/cpum_sf: use READ_ONCE_ALIGNED_128() instead of 128-bit cmpxchg
Use READ_ONCE_ALIGNED_128() to read the previous value in front of a
128-bit cmpxchg loop, instead of (mis-)using a 128-bit cmpxchg operation to
do the same.
Heiko Carstens [Fri, 24 Feb 2023 10:02:36 +0000 (11:02 +0100)]
s390/rwonce: add READ_ONCE_ALIGNED_128() macro
Add an s390 specific READ_ONCE_ALIGNED_128() helper, which can be used for
fast block concurrent (atomic) 128-bit accesses.
The used lpq instruction requires 128-bit alignment. This is also the
reason why the compiler doesn't emit this instruction if __READ_ONCE() is
used for 128-bit accesses.
Ard Biesheuvel [Thu, 23 Feb 2023 20:41:01 +0000 (21:41 +0100)]
arm64: kaslr: don't pretend KASLR is enabled if offset < MIN_KIMG_ALIGN
Our virtual KASLR displacement is a randomly chosen multiple of
2 MiB plus an offset that is equal to the physical placement modulo 2
MiB. This arrangement ensures that we can always use 2 MiB block
mappings (or contiguous PTE mappings for 16k or 64k pages) to map the
kernel.
This means that a KASLR offset of less than 2 MiB is simply the product
of this physical displacement, and no randomization has actually taken
place. Currently, we use 'kaslr_offset() > 0' to decide whether or not
randomization has occurred, and so we misidentify this case.
If the kernel image placement is not randomized, modules are allocated
from a dedicated region below the kernel mapping, which is only used for
modules and not for other vmalloc() or vmap() calls.
When randomization is enabled, the kernel image is vmap()'ed randomly
inside the vmalloc region, and modules are allocated in the vicinity of
this mapping to ensure that relative references are always in range.
However, unlike the dedicated module region below the vmalloc region,
this region is not reserved exclusively for modules, and so ordinary
vmalloc() calls may end up overlapping with it. This should rarely
happen, given that vmalloc allocates bottom up, although it cannot be
ruled out entirely.
The misidentified case results in a placement of the kernel image within
2 MiB of its default address. However, the logic that randomizes the
module region is still invoked, and this could result in the module
region overlapping with the start of the vmalloc region, instead of
using the dedicated region below it. If this happens, a single large
vmalloc() or vmap() call will use up the entire region, and leave no
space for loading modules after that.
Since commit 82046702e288 ("efi/libstub/arm64: Replace 'preferred'
offset with alignment check"), this is much more likely to occur on
systems that boot via EFI but lack an implementation of the EFI RNG
protocol, as in that case, the EFI stub will decide to leave the image
where it found it, and the EFI firmware uses 64k alignment only.
Fix this, by correctly identifying the case where the virtual
displacement is a result of the physical displacement only.
Yuezhang Mo [Fri, 10 Feb 2023 05:33:44 +0000 (13:33 +0800)]
exfat: fix the newly allocated clusters are not freed in error handling
In error handling 'free_cluster', before num_alloc clusters allocated,
p_chain->size will not updated and always 0, thus the newly allocated
clusters are not freed.
Yuezhang Mo [Thu, 9 Feb 2023 09:44:50 +0000 (17:44 +0800)]
exfat: don't print error log in normal case
When allocating a new cluster, exFAT first allocates from the
next cluster of the last cluster of the file. If the last cluster
of the file is the last cluster of the volume, allocate from the
first cluster. This is a normal case, but the following error log
will be printed. It makes users confused, so this commit removes
the error log.
[1960905.181545] exFAT-fs (sdb1): hint_cluster is invalid (262130)
This is because GCC will silently ignore `-falign-functions=N` when
passed `-Os`, resulting in functions not being aligned as we expect.
This is a known issue, and to account for this we modified the kernel to
avoid `-Os` generally. Unfortunately we forgot to account for
CONFIG_CC_OPTIMIZE_FOR_SIZE.
Forbid the use of CALL_OPS with CONFIG_CC_OPTIMIZE_FOR_SIZE=y to prevent
this issue. All exising ftrace features will work as before, though
without the performance benefit of CALL_OPS.
The referenced commit added a wrapper for drm_gem_shmem_get_pages_sgt(),
but in the process it accidentally changed the export type from GPL to
non-GPL. Switch it back to GPL.
drm: omapdrm: Do not use helper unininitialized in omap_fbdev_init()
Clang warns (or errors with CONFIG_WERROR):
../drivers/gpu/drm/omapdrm/omap_fbdev.c:235:6: error: variable 'helper' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (!fbdev)
^~~~~~
../drivers/gpu/drm/omapdrm/omap_fbdev.c:259:26: note: uninitialized use occurs here
drm_fb_helper_unprepare(helper);
^~~~~~
../drivers/gpu/drm/omapdrm/omap_fbdev.c:235:2: note: remove the 'if' if its condition is always false
if (!fbdev)
^~~~~~~~~~~
../drivers/gpu/drm/omapdrm/omap_fbdev.c:228:30: note: initialize the variable 'helper' to silence this warning
struct drm_fb_helper *helper;
^
= NULL
1 error generated.
Return early, as there is nothing for the function to do if memory
cannot be allocated. There is no point in adding another label to just
emit the warning at the end of the function in this case, as memory
allocation failures are already logged.
Herbert Xu [Mon, 27 Feb 2023 08:25:58 +0000 (16:25 +0800)]
crypto: caam - Fix edesc/iv ordering mixup
The attempt to add DMA alignment padding by moving IV to the front
of edesc was completely broken as it didn't change the places where
edesc was freed.
It's also wrong as the IV may still share a cache-line with the
edesc.
Fix this by restoring the original layout and simply reserving
enough memmory so that the IV is on a DMA cache-line by itself.
Michael Ellerman [Tue, 21 Feb 2023 13:03:31 +0000 (00:03 +1100)]
powerpc: Avoid dead code/data elimination when using recordmcount
Although powerpc now has objtool mcount support, it's not enabled in all
configurations due to dependencies.
On those configurations, with some linkers (binutils 2.37 at least),
it's still possible to hit the dreaded "recordmcount bug", eg. errors
such as:
CC kernel/kexec_file.o
Cannot find symbol for section 10: .text.unlikely.
kernel/kexec_file.o: failed
make[1]: *** [scripts/Makefile.build:287 : kernel/kexec_file.o] Error 1
Those errors are much more prevalent when building with
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION, because it places every function
in a separate section.
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION is marked experimental and is not
enabled in any powerpc defconfigs or by major distros. Although it does
have at least some users on 32-bit where kernel size tends to be more
important.
Avoid the build errors by blocking CONFIG_LD_DEAD_CODE_DATA_ELIMINATION
when the build is using recordmcount, rather than objtool. In practice
that means for 64-bit big endian builds, or 64-bit clang builds - both
because they lack CONFIG_MPROFILE_KERNEL.
On 32-bit objtool is always used, so
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION is still available there.
Michael Ellerman [Wed, 22 Feb 2023 06:00:37 +0000 (17:00 +1100)]
powerpc/vmlinux.lds: Add .text.asan/tsan sections
When KASAN/KCSAN are enabled clang generates .text.asan/tsan sections.
Because they are not mentioned in the linker script warnings are
generated, and when orphan handling is set to error that becomes a build
error, eg:
ld.lld: error: vmlinux.a(init/main.o):(.text.tsan.module_ctor) is
being placed in '.text.tsan.module_ctor' ld.lld: error:
vmlinux.a(init/version.o):(.text.tsan.module_ctor) is being placed in
'.text.tsan.module_ctor'
Fix it by adding the sections to our linker script, similar to the
generic change made in 848378812e40 ("vmlinux.lds.h: Handle clang's
module.{c,d}tor sections").
Michael Ellerman [Tue, 21 Feb 2023 10:19:52 +0000 (21:19 +1100)]
powerpc: Drop orphaned VAS MAINTAINERS entry
The MAINTAINERS entry for VAS (Virtual Accelerator Switchboard) no
longer has any maintainers, it just points to linuxppc-dev, since commit 60496069d0ae ("powerpc: Update MAINTAINERS for ibmvnic and VAS").
So just drop the VAS entry, all the paths are already covered by the
main powerpc entry, ie. the output of get_maintainer.pl is unchanged.
Thomas Weißschuh [Mon, 20 Feb 2023 06:46:12 +0000 (06:46 +0000)]
vc_screen: don't clobber return value in vcs_read
Commit 226fae124b2d ("vc_screen: move load of struct vc_data pointer in
vcs_read() to avoid UAF") moved the call to vcs_vc() into the loop.
While doing this it also moved the unconditional assignment of
ret = -ENXIO;
This unconditional assignment was valid outside the loop but within it
it clobbers the actual value of ret.
To avoid this only assign "ret = -ENXIO" when actually needed.
[ Also, the 'goto unlock_out" needs to be just a "break", so that it
does the right thing when it exits on later iterations when partial
success has happened - Linus ]
This fixes three issues on move extents ioctl without auto defrag:
a) In ocfs2_find_victim_alloc_group(), we have to convert bits to block
first in case of global bitmap.
b) In ocfs2_probe_alloc_group(), when finding enough bits in block
group bitmap, we have to back off move_len to start pos as well,
otherwise it may corrupt filesystem.
c) In ocfs2_ioctl_move_extents(), set me_threshold both for non-auto
and auto defrag paths. Otherwise it will set move_max_hop to 0 and
finally cause unexpectedly ENOSPC error.
Currently there are no tools triggering the above issues since
defragfs.ocfs2 enables auto defrag by default. Tested with manually
changing defragfs.ocfs2 to run non auto defrag path.
This bug has the same root cause of 'commit 7f27ec978b0e ("ocfs2: call
ocfs2_journal_access_di() before ocfs2_journal_dirty() in
ocfs2_write_end_nolock()")'. For this bug, jbd2_journal_restart() is
called by ocfs2_split_extent() during defragmenting.
How to fix
For ocfs2_split_extent() can handle journal operations totally by itself.
Caller doesn't need to call journal access/dirty pair, and caller only
needs to call journal start/stop pair. The fix method is to remove
journal access/dirty from __ocfs2_move_extent().
The discussion for this patch:
https://oss.oracle.com/pipermail/ocfs2-devel/2023-February/000647.html
Konrad Dybcio [Fri, 17 Feb 2023 20:35:16 +0000 (21:35 +0100)]
mailmap: map Georgi Djakov's old Linaro address to his current one
Georgi's old email is still picked up by the likes of get_maintainer.pl
and it keeps bouncing every time one submits an interconnect patch. Map
it to his current @kernel.org one.
Naoya Horiguchi [Tue, 21 Feb 2023 08:59:05 +0000 (17:59 +0900)]
mm/hwpoison: convert TTU_IGNORE_HWPOISON to TTU_HWPOISON
After a memory error happens on a clean folio, a process unexpectedly
receives SIGBUS when it accesses the error page. This SIGBUS killing is
pointless and simply degrades the level of RAS of the system, because the
clean folio can be dropped without any data lost on memory error handling
as we do for a clean pagecache.
When memory_failure() is called on a clean folio, try_to_unmap() is called
twice (one from split_huge_page() and one from hwpoison_user_mappings()).
The root cause of the issue is that pte conversion to hwpoisoned entry is
now done in the first call of try_to_unmap() because PageHWPoison is
already set at this point, while it's actually expected to be done in the
second call. This behavior disturbs the error handling operation like
removing pagecache, which results in the malfunction described above.
So convert TTU_IGNORE_HWPOISON into TTU_HWPOISON and set TTU_HWPOISON only
when we really intend to convert pte to hwpoison entry. This can prevent
other callers of try_to_unmap() from accidentally converting to hwpoison
entries.
Mikhail Zaslonko [Tue, 21 Feb 2023 13:16:17 +0000 (14:16 +0100)]
lib/zlib: DFLTCC deflate does not write all available bits for Z_NO_FLUSH
DFLTCC deflate with Z_NO_FLUSH might generate a corrupted stream when the
output buffer is not large enough to fit all the deflate output at once.
The problem takes place on closing the deflate block since flush_pending()
might leave some output bits not written. Similar problem for software
deflate with Z_BLOCK flush option (not supported by kernel zlib deflate)
has been fixed a while ago in userspace zlib but the fix never got to the
kernel.
Now flush_pending() flushes the bit buffer before copying out the byte
buffer, in order to really flush as much as possible.
Currently there are no users of DFLTCC deflate with Z_NO_FLUSH option in
the kernel so the problem remained hidden for a while.
This commit is based on the old zlib commit:
https://github.com/madler/zlib/commit/0b828b4
andrew.yang [Wed, 22 Feb 2023 06:42:20 +0000 (14:42 +0800)]
mm/damon/paddr: fix missing folio_put()
damon_get_folio() would always increase folio _refcount and
folio_isolate_lru() would increase folio _refcount if the folio's lru flag
is set.
If an unevictable folio isolated successfully, there will be two more
_refcount. The one from folio_isolate_lru() will be decreased in
folio_puback_lru(), but the other one from damon_get_folio() will be left
behind. This causes a pin page.
Whatever the case, the _refcount from damon_get_folio() should be
decreased.
Vlastimil Babka [Tue, 28 Feb 2023 01:00:14 +0000 (17:00 -0800)]
mm/mremap: fix dup_anon_vma() in vma_merge() case 4
In case 4, we are shrinking 'prev' (PPPP in the comment) and expanding
'mid' (NNNN). So we need to make sure 'mid' clones the anon_vma from
'prev', if it doesn't have any. After commit 0503ea8f5ba7 ("mm/mmap:
remove __vma_adjust()") we can fail to do that due to wrong parameters for
dup_anon_vma(). The call is a no-op because res == next, adjust == mid
and mid == next. Fix it.
It falls down to do_faccessat without the AT_EACCESS flag, which in turn
results in allocation of new creds in order to modify fsuid/fsgid and
caps. This is a very expensive process single-threaded and most notably
multi-threaded, with numerous structures getting refed and unrefed on
imminent new cred destruction.
Turns out for typical consumers the resulting creds would be identical
and this can be checked upfront, avoiding the hard work.
An access benchmark plugged into will-it-scale running on Cascade Lake
shows:
Linus Torvalds [Tue, 28 Feb 2023 00:18:51 +0000 (16:18 -0800)]
Merge tag 'f2fs-for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, we've got a huge number of patches that improve code
readability along with minor bug fixes, while we've mainly fixed some
critical issues in recently-added per-block age-based extent_cache,
atomic write support, and some folio cases.
Enhancements:
- add sysfs nodes to set last_age_weight and manage
discard_io_aware_gran
- show ipu policy in debugfs
- reduce stack memory cost by using bitfield in struct f2fs_io_info
- introduce trace_f2fs_replace_atomic_write_block
- enhance iostat support and adds flush commands
Bug fixes:
- revert "f2fs: truncate blocks in batch in __complete_revoke_list()"
- fix kernel crash on the atomic write abort flow
- call clear_page_private_reference in .{release,invalid}_folio
- support .migrate_folio for compressed inode
- fix cgroup writeback accounting with fs-layer encryption
- retry to update the inode page given data corruption
- fix kernel crash due to NULL io->bio
- fix some bugs in per-block age-based extent_cache:
- wrong calculation of block age
- update age extent in f2fs_do_zero_range()
- update age extent correctly during truncation"
* tag 'f2fs-for-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (81 commits)
f2fs: drop unnecessary arg for f2fs_ioc_*()
f2fs: Revert "f2fs: truncate blocks in batch in __complete_revoke_list()"
f2fs: synchronize atomic write aborts
f2fs: fix wrong segment count
f2fs: replace si->sbi w/ sbi in stat_show()
f2fs: export ipu policy in debugfs
f2fs: make kobj_type structures constant
f2fs: fix to do sanity check on extent cache correctly
f2fs: add missing description for ipu_policy node
f2fs: fix to set ipu policy
f2fs: fix typos in comments
f2fs: fix kernel crash due to null io->bio
f2fs: use iostat_lat_type directly as a parameter in the iostat_update_and_unbind_ctx()
f2fs: add sysfs nodes to set last_age_weight
f2fs: fix f2fs_show_options to show nogc_merge mount option
f2fs: fix cgroup writeback accounting with fs-layer encryption
f2fs: fix wrong calculation of block age
f2fs: fix to update age extent in f2fs_do_zero_range()
f2fs: fix to update age extent correctly during truncation
f2fs: fix to avoid potential memory corruption in __update_iostat_latency()
...
David Gow [Sat, 25 Feb 2023 01:45:30 +0000 (09:45 +0800)]
kunit: Fix 'hooks.o' build by recursing into kunit
KUnit's 'hooks.o' file need to be built-in whenever KUnit is enabled
(even if CONFIG_KUNIT=m). We'd previously attemtped to do this by
adding 'kunit/hooks.o' to obj-y in lib/Makefile, but this caused hooks.c
to be rebuilt even when it was unchanged.
Instead, always recurse into lib/kunit using obj-y when KUnit is
enabled, and add the hooks there.
Arınç ÜNAL [Tue, 21 Feb 2023 09:24:35 +0000 (12:24 +0300)]
mips: ralink: make SOC_MT7621 select PINCTRL
Currently, out of every Ralink SoC, only the dt-binding of the MT7621 SoC
uses pinctrl. Because of this, PINCTRL is not selected at all. Make
SOC_MT7621 select PINCTRL.
Remove PINCTRL_MT7621, enabling it for the MT7621 SoC will be handled under
the PINCTRL_MT7621 option.
projects / linux.git / log