Linus Torvalds [Wed, 16 Nov 2022 18:40:00 +0000 (10:40 -0800)]
Merge tag 'pinctrl-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Aere is a hopefully final round of pin control fixes. Nothing special,
driver fixes and we caught a potential NULL pointer exception.
- Fix a potential NULL dereference in the core!
- Fix all pin mux routes in the Rockchop PX30 driver
- Fix the UFS pins in the Qualcomm SC8280XP driver
- Fix bias disabling in the Mediatek driver
- Fix debounce time settings in the Mediatek driver"
* tag 'pinctrl-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: Export debounce time tables
pinctrl: mediatek: Fix EINT pins input debounce time configuration
pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
pinctrl: mediatek: common-v2: Fix bias-disable for PULL_PU_PD_RSEL_TYPE
pinctrl: qcom: sc8280xp: Rectify UFS reset pins
pinctrl: rockchip: list all pins in a possible mux route for PX30
Linus Torvalds [Wed, 16 Nov 2022 18:36:13 +0000 (10:36 -0800)]
Merge tag 'platform-drivers-x86-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Surface Pro 9 and Surface Laptop 5 kbd, battery, etc support (this
is just a few hw-id additions)
- A couple of other hw-id / DMI-quirk additions
- A few small bug fixes + 1 build fix
* tag 'platform-drivers-x86-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ideapad-laptop: Add module parameters to match DMI quirk tables
platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops
platform/x86: hp-wmi: Ignore Smart Experience App event
platform/surface: aggregator_registry: Add support for Surface Laptop 5
platform/surface: aggregator_registry: Add support for Surface Pro 9
platform/surface: aggregator: Do not check for repeated unsequenced packets
platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)
platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when virtualized
platform/x86: thinkpad_acpi: Enable s2idle quirk for 21A1 machine type
platform/x86/amd: pmc: Add new ACPI ID AMDI0009
platform/x86/amd: pmc: Remove more CONFIG_DEBUG_FS checks
Anastasia Belova [Wed, 16 Nov 2022 14:10:27 +0000 (17:10 +0300)]
cifs: add check for returning value of SMB2_set_info_init
If the returning value of SMB2_set_info_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0967e5457954 ("cifs: use a compound for setting an xattr") Signed-off-by: Anastasia Belova <[email protected]> Signed-off-by: Steve French <[email protected]>
Davide Tronchin [Wed, 16 Nov 2022 15:59:50 +0000 (16:59 +0100)]
USB: serial: option: add u-blox LARA-L6 modem
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Davide Tronchin [Wed, 16 Nov 2022 15:59:49 +0000 (16:59 +0100)]
USB: serial: option: add u-blox LARA-R6 00B modem
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Davide Tronchin [Wed, 16 Nov 2022 15:59:48 +0000 (16:59 +0100)]
USB: serial: option: remove old LARA-R6 PID
Remove the UBLOX_PRODUCT_R6XX 0x90fa association since LARA-R6 00B final
product uses a new USB composition with different PID. 0x90fa PID used
only by LARA-R6 internal prototypes.
Move 0x90fa PID directly in the option_ids array since used by other
Qualcomm based modem vendors as pointed out in:
Xiongfeng Wang [Mon, 14 Nov 2022 08:31:00 +0000 (16:31 +0800)]
mmc: sdhci-pci: Fix possible memory leak caused by missing pci_dev_put()
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before amd_probe() returns. There is no problem for the 'smbus_dev ==
NULL' branch because pci_dev_put() can also handle the NULL input
parameter case.
The SD card is recognized failed sometimes when resume from suspend.
Because CD# debounce time too long then card present report wrong.
Finally, card is recognized failed.
Yann Gautier [Fri, 28 Oct 2022 07:37:40 +0000 (09:37 +0200)]
mmc: core: properly select voltage range without power cycle
In mmc_select_voltage(), if there is no full power cycle, the voltage
range selected at the end of the function will be on a single range
(e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V),
the mask shift should be reduced by 1.
This issue was triggered by using a specific SD-card (Verbatim Premium
16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes
and there is no power cycle. And the card was failing to switch to
high-speed mode. When adding the range 3.2V/3.3V for this card with the
proposed shift change, the card can switch to high-speed mode.
Jakub Sitnicki [Mon, 14 Nov 2022 19:16:19 +0000 (20:16 +0100)]
l2tp: Serialize access to sk_user_data with sk_callback_lock
sk->sk_user_data has multiple users, which are not compatible with each
other. Writers must synchronize by grabbing the sk->sk_callback_lock.
l2tp currently fails to grab the lock when modifying the underlying tunnel
socket fields. Fix it by adding appropriate locking.
We err on the side of safety and grab the sk_callback_lock also inside the
sk_destruct callback overridden by l2tp, even though there should be no
refs allowing access to the sock at the time when sk_destruct gets called.
v4:
- serialize write to sk_user_data in l2tp sk_destruct
v3:
- switch from sock lock to sk_callback_lock
- document write-protection for sk_user_data
v2:
- update Fixes to point to origin of the bug
- use real names in Reported/Tested-by tags
Vasily Gorbik [Fri, 4 Nov 2022 11:06:47 +0000 (12:06 +0100)]
s390: avoid using global register for current_stack_pointer
Commit 30de14b1884b ("s390: current_stack_pointer shouldn't be a
function") made current_stack_pointer a global register variable like
on many other architectures. Unfortunately on s390 it uncovers old
gcc bug which is fixed only since gcc-9.1 [gcc commit 3ad7fed1cc87
("S/390: Fix PR89775. Stackpointer save/restore instructions removed")]
and backported to gcc-8.4 and later. Due to this bug gcc versions prior
to 8.4 generate broken code which leads to stack corruptions.
Current minimal gcc version required to build the kernel is declared
as 5.1. It is not possible to fix all old gcc versions, so work
around this problem by avoiding using global register variable for
current_stack_pointer.
Fixes: 30de14b1884b ("s390: current_stack_pointer shouldn't be a function") Reviewed-by: Heiko Carstens <[email protected]> Signed-off-by: Vasily Gorbik <[email protected]> Signed-off-by: Alexander Gordeev <[email protected]>
Gerald Schaefer [Thu, 27 Oct 2022 14:19:38 +0000 (16:19 +0200)]
s390/dcssblk: fix deadlock when adding a DCSS
After the rework from commit 1ebe2e5f9d68 ("block: remove
GENHD_FL_EXT_DEVT"), when calling device_add_disk(), dcssblk will end up
in disk_scan_partitions(), and not break out early w/o GENHD_FL_NO_PART.
This will trigger implicit open/release via blkdev_get/put_whole()
later. dcssblk_release() will then deadlock on dcssblk_devices_sem
semaphore, which is already held from dcssblk_add_store() when calling
device_add_disk().
dcssblk does not support partitions (DCSSBLK_MINORS_PER_DISK == 1), and
never scanned partitions before. Therefore restore the previous
behavior, and explicitly disallow partition scanning by setting the
GENHD_FL_NO_PART flag. This will also prevent this deadlock scenario.
Nicholas Piggin [Wed, 16 Nov 2022 04:39:53 +0000 (14:39 +1000)]
powerpc: Fix writable sections being moved into the rodata region
.data.rel.ro* catches .data.rel.root_cpuacct, and the kernel crashes on
a store in css_clear_dir. At least we know read-only data protection is
working...
Yuan Can [Mon, 14 Nov 2022 14:22:25 +0000 (14:22 +0000)]
net: thunderbolt: Fix error handling in tbnet_init()
A problem about insmod thunderbolt-net failed is triggered with following
log given while lsmod does not show thunderbolt_net:
insmod: ERROR: could not insert module thunderbolt-net.ko: File exists
The reason is that tbnet_init() returns tb_register_service_driver()
directly without checking its return value, if tb_register_service_driver()
failed, it returns without removing property directory, resulting the
property directory can never be created later.
Fix by remove property directory when tb_register_service_driver() returns
error.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable") Signed-off-by: Yuan Can <[email protected]> Acked-by: Mika Westerberg <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Guo Jin [Tue, 8 Nov 2022 06:01:26 +0000 (14:01 +0800)]
locking: Fix qspinlock/x86 inline asm error
When compiling linux 6.1.0-rc3 configured with CONFIG_64BIT=y and
CONFIG_PARAVIRT_SPINLOCKS=y on x86_64 using LLVM 11.0, an error:
"<inline asm> error: changed section flags for .spinlock.text,
expected:: 0x6" occurred.
The reason is the .spinlock.text in kernel/locking/qspinlock.o
is used many times, but its flags are omitted in subsequent use.
LLVM 11.0 assembler didn't permit to
leave out flags in subsequent uses of the same sections.
So this patch adds the corresponding flags to avoid above error.
Adrian Hunter [Sat, 12 Nov 2022 15:15:08 +0000 (17:15 +0200)]
perf/x86/intel/pt: Fix sampling using single range output
Deal with errata TGL052, ADL037 and RPL017 "Trace May Contain Incorrect
Data When Configured With Single Range Output Larger Than 4KB" by
disabling single range output whenever larger than 4KB.
Ravi Bangoria [Mon, 14 Nov 2022 04:40:29 +0000 (10:10 +0530)]
perf/x86/amd: Fix crash due to race between amd_pmu_enable_all, perf NMI and throttling
amd_pmu_enable_all() does:
if (!test_bit(idx, cpuc->active_mask))
continue;
amd_pmu_enable_event(cpuc->events[idx]);
A perf NMI of another event can come between these two steps. Perf NMI
handler internally disables and enables _all_ events, including the one
which nmi-intercepted amd_pmu_enable_all() was in process of enabling.
If that unintentionally enabled event has very low sampling period and
causes immediate successive NMI, causing the event to be throttled,
cpuc->events[idx] and cpuc->active_mask gets cleared by x86_pmu_stop().
This will result in amd_pmu_enable_event() getting called with event=NULL
when amd_pmu_enable_all() resumes after handling the NMIs. This causes a
kernel crash:
amd_pmu_disable_all()/amd_pmu_enable_all() calls inside perf NMI handler
were recently added as part of BRS enablement but I'm not sure whether
we really need them. We can just disable BRS in the beginning and enable
it back while returning from NMI. This will solve the issue by not
enabling those events whose active_masks are set but are not yet enabled
in hw pmu.
David S. Miller [Wed, 16 Nov 2022 09:10:29 +0000 (09:10 +0000)]
Merge branch 'microchip-fixes'
Shang XiaoJing says:
====================
net: microchip: Fix potential null-ptr-deref due to create_singlethread_workqueue()
There are some functions call create_singlethread_workqueue() without
checking ret value, and the NULL workqueue_struct pointer may causes
null-ptr-deref. Will be fixed by this patch.
====================
Hans de Goede [Tue, 15 Nov 2022 19:34:00 +0000 (20:34 +0100)]
platform/x86: ideapad-laptop: Add module parameters to match DMI quirk tables
Add module parameters to allow setting the hw_rfkill_switch and
set_fn_lock_led feature flags for testing these on laptops which are not
on the DMI-id based allow lists for these 2 flags.
Arnav Rawat [Fri, 11 Nov 2022 14:32:09 +0000 (14:32 +0000)]
platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops
Commit 3ae86d2d4704 ("platform/x86: ideapad-laptop: Fix Legion 5 Fn lock
LED") uses the WMI event-id for the fn-lock event on some Legion 5 laptops
to manually toggle the fn-lock LED because the EC does not do it itself.
However, the same WMI ID is also sent on some Yoga laptops. Here, setting
the fn-lock state is not valid behavior, and causes the EC to spam
interrupts until the laptop is rebooted.
Add a set_fn_lock_led_list[] DMI-id list and only enable the workaround to
manually set the LED on models on this list.
Maximilian Luz [Tue, 15 Nov 2022 23:14:40 +0000 (00:14 +0100)]
platform/surface: aggregator_registry: Add support for Surface Laptop 5
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal HID devices (including
touchpad and keyboard) on the Surface Laptop 5.
Damien Le Moal [Tue, 25 Oct 2022 04:39:31 +0000 (13:39 +0900)]
zonefs: fix zone report size in __zonefs_io_error()
When an IO error occurs, the function __zonefs_io_error() is used to
issue a zone report to obtain the latest zone information from the
device. This function gets a zone report for all zones used as storage
for a file, which is always 1 zone except for files representing
aggregated conventional zones.
The number of zones of a zone report for a file is calculated in
__zonefs_io_error() by doing a bit-shift of the inode i_zone_size field,
which is equal to or larger than the device zone size. However, this
calculation does not take into account that the last zone of a zoned
device may be smaller than the zone size reported by bdev_zone_sectors()
(which is used to set the bit shift size). As a result, if an error
occurs for an IO targetting such last smaller zone, the zone report will
ask for 0 zones, leading to an invalid zone report.
Fix this by using the fact that all files require a 1 zone report,
except if the inode i_zone_size field indicates a zone size larger than
the device zone size. This exception case corresponds to a mount with
aggregated conventional zones.
A check for this exception is added to the file inode initialization
during mount. If an invalid setup is detected, emit an error and fail
the mount (check contributed by Johannes Thumshirn).
Vladimir Oltean [Mon, 14 Nov 2022 14:35:51 +0000 (16:35 +0200)]
net: dsa: don't leak tagger-owned storage on switch driver unbind
In the initial commit dc452a471dba ("net: dsa: introduce tagger-owned
storage for private and shared data"), we had a call to
tag_ops->disconnect(dst) issued from dsa_tree_free(), which is called at
tree teardown time.
There were problems with connecting to a switch tree as a whole, so this
got reworked to connecting to individual switches within the tree. In
this process, tag_ops->disconnect(ds) was made to be called only from
switch.c (cross-chip notifiers emitted as a result of dynamic tag proto
changes), but the normal driver teardown code path wasn't replaced with
anything.
Solve this problem by adding a function that does the opposite of
dsa_switch_setup_tag_protocol(), which is called from the equivalent
spot in dsa_switch_teardown(). The positioning here also ensures that we
won't have any use-after-free in tagging protocol (*rcv) ops, since the
teardown sequence is as follows:
dsa_tree_teardown
-> dsa_tree_teardown_master
-> dsa_master_teardown
-> unsets master->dsa_ptr, making no further packets match the
ETH_P_XDSA packet type handler
-> dsa_tree_teardown_ports
-> dsa_port_teardown
-> dsa_slave_destroy
-> unregisters DSA net devices, there is even a synchronize_net()
in unregister_netdevice_many()
-> dsa_tree_teardown_switches
-> dsa_switch_teardown
-> dsa_switch_teardown_tag_protocol
-> finally frees the tagger-owned storage
Wei Yongjun [Mon, 14 Nov 2022 11:05:19 +0000 (11:05 +0000)]
net/x25: Fix skb leak in x25_lapb_receive_frame()
x25_lapb_receive_frame() using skb_copy() to get a private copy of
skb, the new skb should be freed in the undersized/fragmented skb
error handling path. Otherwise there is a memory leak.
Liu Jian [Mon, 14 Nov 2022 09:55:49 +0000 (17:55 +0800)]
net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in ag71xx_open()
If ag71xx_hw_enable() fails, call phylink_disconnect_phy() to clean up.
And if phylink_of_phy_connect() fails, nothing needs to be done.
Compile tested only.
Linus Torvalds [Tue, 15 Nov 2022 22:56:23 +0000 (14:56 -0800)]
AMerge tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfx fixes from David Howells:
"Two fixes, affecting the functions that iterates over the pagecache
unmarking or unlocking pages after an op is complete:
- xas_for_each() loops must call xas_retry() first thing and
immediately do a "continue" in the case that the extracted value is
a special value that indicates that the walk raced with a
modification. Fix the unlock and unmark loops to do this.
- The maths in the unlock loop is dodgy as it could, theoretically,
at some point in the future end up with a starting file pointer
that is in the middle of a folio. This will cause a subtraction to
go negative - but the number is unsigned. Fix the maths to use
absolute file positions instead of relative page indices"
* tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix dodgy maths
netfs: Fix missing xas_retry() calls in xarray iteration
Simon Rettberg [Thu, 6 Oct 2022 09:33:14 +0000 (11:33 +0200)]
drm/display: Don't assume dual mode adaptors support i2c sub-addressing
Current dual mode adaptor ("DP++") detection code assumes that all
adaptors support i2c sub-addressing for read operations from the
DP-HDMI adaptor ID buffer. It has been observed that multiple
adaptors do not in fact support this, and always return data starting
at register 0. On affected adaptors, the code fails to read the proper
registers that would identify the device as a type 2 adaptor, and
handles those as type 1, limiting the TMDS clock to 165MHz, even if
the according register would announce a higher TMDS clock.
Fix this by always reading the ID buffer starting from offset 0, and
discarding any bytes before the actual offset of interest.
We tried finding authoritative documentation on whether or not this is
allowed behaviour, but since all the official VESA docs are paywalled,
the best we could come up with was the spec sheet for Texas Instruments'
SNx5DP149 chip family.[1] It explicitly mentions that sub-addressing is
supported for register writes, but *not* for reads (See NOTE in
section 8.5.3). Unless TI openly decided to violate the VESA spec, one
could take that as a hint that sub-addressing is in fact not mandated
by VESA.
The other two adaptors affected used the PS8409(A) and the LT8611,
according to the data returned from their ID buffers.
Linus Torvalds [Tue, 15 Nov 2022 18:30:34 +0000 (10:30 -0800)]
Merge tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Most patches randomly fix error paths or corner cases in fscache mode
reported recently. One fixes an invalid access relating to fragments
on crafted images.
Summary:
- Fix packed_inode invalid access when reading fragments on crafted
images
- Add a missing erofs_put_metabuf() in an error path in fscache mode
- Fix incorrect `count' for unmapped extents in fscache mode
- Fix use-after-free of fsid and domain_id string when remounting
- Fix missing xas_retry() in fscache mode"
* tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix missing xas_retry() in fscache mode
erofs: fix use-after-free of fsid and domain_id string
erofs: get correct count for unmapped range in fscache mode
erofs: put metabuf in error path in fscache mode
erofs: fix general protection fault when reading fragment
Alex Deucher [Fri, 11 Nov 2022 17:50:38 +0000 (12:50 -0500)]
drm/amdgpu: there is no vbios fb on devices with no display hw (v2)
If we enable virtual display functionality on parts with
no display hardware we can end up trying to check for and
reserve the vbios FB area on devices where it doesn't exist.
Check if display hardware is actually present on the hardware
before trying to reserve the memory.
Eric Huang [Mon, 14 Nov 2022 16:43:48 +0000 (11:43 -0500)]
drm/amdkfd: Fix a memory limit issue
It is to resolve a regression, which fails to allocate
VRAM due to no free memory in application, the reason
is we add check of vram_pin_size for memory limit, and
application is pinning the memory for Peerdirect, KFD
should not count it in memory limit. So removing
vram_pin_size will resolve it.
Melissa Wen [Thu, 3 Nov 2022 18:45:00 +0000 (17:45 -0100)]
drm/amd/display: don't enable DRM CRTC degamma property for DCE
DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.
Dillon Varone [Thu, 3 Nov 2022 22:33:38 +0000 (18:33 -0400)]
drm/amd/display: Fix prefetch calculations for dcn32
[Description]
Prefetch calculation loop was not exiting until utilizing all of vstartup if it
failed once. Locals need to be reset on each iteration of the loop.
Roman Li [Thu, 3 Nov 2022 21:33:07 +0000 (17:33 -0400)]
drm/amd/display: Fix optc2_configure warning on dcn314
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
George Shen [Wed, 2 Nov 2022 03:03:03 +0000 (23:03 -0400)]
drm/amd/display: Fix calculation for cursor CAB allocation
[Why]
The cursor size (in memory) is currently incorrectly calculated,
resulting not enough CAB being allocated for static screen cursor
in MALL refresh. This results in cursor image corruption.
[How]
Use cursor pitch instead of cursor width when calculating cursor size.
Update num cache lines calculation to use the result of the cursor size
calculation instead of manually recalculating again.
It turns out this causes logically active but disconnected DP MST
connectors to disappear from the KMS resources list, and Mutter
then assumes the connector is already disabled. Later on Mutter tries
to re-use the same CRTC but fails since on the kernel side it's still
tied to the disconnected DP MST connector.
George Shen [Wed, 2 Nov 2022 19:06:48 +0000 (15:06 -0400)]
drm/amd/display: Support parsing VRAM info v3.0 from VBIOS
[Why]
For DCN3.2 and DCN3.21, VBIOS has switch to using v3.0 of the VRAM
info struct. We should read and override the VRAM info in driver with
values provided by VBIOS to support memory downbin cases.
Stylon Wang [Wed, 26 Oct 2022 13:00:40 +0000 (21:00 +0800)]
drm/amd/display: Fix invalid DPIA AUX reply causing system hang
[Why]
Some DPIA AUX replies have incorrect data length from original request.
This could lead to overwriting of destination buffer if reply length is
larger, which could cause invalid access to stack since many destination
buffers are declared as local variables.
[How]
Check for invalid length from DPIA AUX replies and trigger a retry if
reply length is not the same as original request. A DRM_WARN() dmesg log
is also produced.
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Stylon Wang [Mon, 24 Oct 2022 07:36:16 +0000 (15:36 +0800)]
drm/amd/display: Fix access timeout to DPIA AUX at boot time
[Why]
Since introduction of patch "Query DPIA HPD status.", link detection at
boot could be accessing DPIA AUX, which will not succeed until
DMUB outbox messaging is enabled and results in below dmesg logs:
Dong Chenchen [Thu, 10 Nov 2022 14:33:14 +0000 (22:33 +0800)]
drm/amdgpu: Fix memory leak in amdgpu_cs_pass1
When p->gang_size equals 0, amdgpu_cs_pass1() will return directly
without freeing chunk_array, which will cause a memory leak issue,
this patch fixes it.
Takashi Iwai [Tue, 15 Nov 2022 17:02:35 +0000 (18:02 +0100)]
ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book Pro 360
Samsung Galaxy Book Pro 360 (13" 2021 NP930QBD-ke1US) with codec SSID
144d:c1a6 requires the same workaround for enabling the speaker amp
like other Samsung models with ALC298 codec.
Emil Flink [Tue, 15 Nov 2022 14:45:01 +0000 (15:45 +0100)]
ALSA: hda/realtek: fix speakers for Samsung Galaxy Book Pro
The Samsung Galaxy Book Pro seems to have the same issue as a few
other Samsung laptops, detailed in kernel bug report 207423. Sound from
headphone jack works, but not the built-in speakers.
David Howells [Fri, 4 Nov 2022 15:36:49 +0000 (15:36 +0000)]
netfs: Fix dodgy maths
Fix the dodgy maths in netfs_rreq_unlock_folios(). start_page could be
inside the folio, in which case the calculation of pgpos will be come up
with a negative number (though for the moment rreq->start is rounded down
earlier and folios would have to get merged whilst locked)
Alter how this works to just frame the tracking in terms of absolute file
positions, rather than offsets from the start of the I/O request. This
simplifies the maths and makes it easier to follow.
Fix the issue by using folio_pos() and folio_size() to calculate the end
position of the page.
David Howells [Thu, 3 Nov 2022 16:08:14 +0000 (16:08 +0000)]
netfs: Fix missing xas_retry() calls in xarray iteration
netfslib has a number of places in which it performs iteration of an xarray
whilst being under the RCU read lock. It *should* call xas_retry() as the
first thing inside of the loop and do "continue" if it returns true in case
the xarray walker passed out a special value indicating that the walk needs
to be redone from the root[*].
Fix this by adding the missing retry checks.
[*] I wonder if this should be done inside xas_find(), xas_next_node() and
suchlike, but I'm told that's not an simple change to effect.
This can cause an oops like that below. Note the faulting address - this
is an internal value (|0x2) returned from xarray.
Changes:
========
ver #2)
- Changed an unsigned int to a size_t to reduce the likelihood of an
overflow as per Willy's suggestion.
- Added an additional patch to fix the maths.
Maximilian Luz [Sun, 13 Nov 2022 18:59:51 +0000 (19:59 +0100)]
platform/surface: aggregator_registry: Add support for Surface Pro 9
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal and type-cover HID devices
(including sensors, touchpad, keyboard, and other miscellaneous devices)
on the Surface Pro 9.
This does not include support for a tablet-mode switch yet, as that is
now handled via the POS subsystem (unlike the Surface Pro 8, where it is
handled via the KIP subsystem) and therefore needs further changes.
While we're at it, also add the missing comment for the Surface Pro 8.
Maximilian Luz [Sun, 13 Nov 2022 18:59:50 +0000 (19:59 +0100)]
platform/surface: aggregator: Do not check for repeated unsequenced packets
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Xiongfeng Wang [Fri, 11 Nov 2022 10:07:52 +0000 (18:07 +0800)]
platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before asus_wmi_set_xusb2pr() returns.
Roger Pau Monné [Thu, 10 Nov 2022 16:31:44 +0000 (17:31 +0100)]
platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when virtualized
The current logic in the Intel PMC driver will forcefully attach it
when detecting any CPU on the intel_pmc_core_platform_ids array,
even if the matching ACPI device is not present.
There's no checking in pmc_core_probe() to assert that the PMC device
is present, and hence on virtualized environments the PMC device
probes successfully, even if the underlying registers are not present.
Before commit 21ae43570940 ("platform/x86: intel_pmc_core: Substitute PCI
with CPUID enumeration") the driver would check for the presence of a
specific PCI device, and that prevented the driver from attaching when
running virtualized.
Fix by only forcefully attaching the PMC device when not running
virtualized. Note that virtualized platforms can still get the device
to load if the appropriate ACPI device is present on the tables
provided to the VM.
Make an exception for the Xen initial domain, which does have full
hardware access, and hence can attach to the PMC if present.
Lennard Gäher [Tue, 8 Nov 2022 07:20:23 +0000 (08:20 +0100)]
platform/x86: thinkpad_acpi: Enable s2idle quirk for 21A1 machine type
Previously, the s2idle quirk was only active for the 21A0 machine type
of the P14s Gen2a product. This also enables it for the second 21A1 type,
thus reducing wake-up times from s2idle.
Conor Dooley [Wed, 9 Nov 2022 21:22:18 +0000 (21:22 +0000)]
MAINTAINERS: generify the Microchip RISC-V entry name
These drivers work on our other FPGAs, for example the non-SoC PolarFire
connected to an FU-540 via chiplink. Make the entry a wee bit more
generic to match. While at it, remove the / from the heading so that it
matches other, neighbouring RISC-V entries.
Conor Dooley [Wed, 9 Nov 2022 21:22:17 +0000 (21:22 +0000)]
MAINTAINERS: add entries for misc. RISC-V SoC drivers and devicetrees
Following some discussion both on & off list, I have volunteered to take
over maintaining the miscellaneous RISC-V devicetrees & soc drivers from
Palmer to ease his load.
So far only SiFive and Microchip have stuff in drivers/soc. For the
former, a SiFive entry exists with a dead GitHub repo - so remove that
to avoid confusion since the patches for drivers/soc & devicetrees will
be routed via my tree & other drivers go through their subsystem trees.
The Microchip directory only contains a RISC-V driver for now, but is
likely to contain drivers for other archs in the future. To that end,
change the PolarFire SoC entry to specifically mention the RISC-V driver
& the new directory level entry does not mention an architecture.
Ido Schimmel [Mon, 14 Nov 2022 08:45:09 +0000 (10:45 +0200)]
bridge: switchdev: Fix memory leaks when changing VLAN protocol
The bridge driver can offload VLANs to the underlying hardware either
via switchdev or the 8021q driver. When the former is used, the VLAN is
marked in the bridge driver with the 'BR_VLFLAG_ADDED_BY_SWITCHDEV'
private flag.
To avoid the memory leaks mentioned in the cited commit, the bridge
driver will try to delete a VLAN via the 8021q driver if the VLAN is not
marked with the previously mentioned flag.
When the VLAN protocol of the bridge changes, switchdev drivers are
notified via the 'SWITCHDEV_ATTR_ID_BRIDGE_VLAN_PROTOCOL' attribute, but
the 8021q driver is also called to add the existing VLANs with the new
protocol and delete them with the old protocol.
In case the VLANs were offloaded via switchdev, the above behavior is
both redundant and buggy. Redundant because the VLANs are already
programmed in hardware and drivers that support VLAN protocol change
(currently only mlx5) change the protocol upon the switchdev attribute
notification. Buggy because the 8021q driver is called despite these
VLANs being marked with 'BR_VLFLAG_ADDED_BY_SWITCHDEV'. This leads to
memory leaks [1] when the VLANs are deleted.
Fix by not calling the 8021q driver for VLANs that were already
programmed via switchdev.
====================
net: hns3: This series bugfix for the HNS3 ethernet driver.
This series includes some bugfix for the HNS3 ethernet driver.
Patch 1# fix incorrect hw rss hash type of rx packet. Fixes: 796640778c26 ("net: hns3: support RXD advanced layout") Fixes: 232fc64b6e62 ("net: hns3: Add HW RSS hash information to RX skb") Fixes: ea4858670717 ("net: hns3: handle the BD info on the last BD of the packet")
Patch 2# fix return value check bug of rx copybreak. Fixes: e74a726da2c4 ("net: hns3: refactor hns3_nic_reuse_page()") Fixes: 99f6b5fb5f63 ("net: hns3: use bounce buffer when rx page can not be reused")
Patch 3# net: hns3: fix setting incorrect phy link ksettings
for firmware in resetting process Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs") Fixes: c5ef83cbb1e9 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config") Fixes: 2312e050f42b ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo")
====================
Guangbin Huang [Mon, 14 Nov 2022 08:20:48 +0000 (16:20 +0800)]
net: hns3: fix setting incorrect phy link ksettings for firmware in resetting process
Currently, if driver is in phy-imp(phy controlled by imp firmware) mode, as
driver did not update phy link ksettings after initialization process or
not update advertising when getting phy link ksettings from firmware, it
may set incorrect phy link ksettings for firmware in resetting process.
So fix it.
Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs") Fixes: c5ef83cbb1e9 ("net: hns3: fix for phy_addr error in hclge_mac_mdio_config") Fixes: 2312e050f42b ("net: hns3: Fix for deadlock problem occurring when unregistering ae_algo") Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: Hao Lan <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
Jie Wang [Mon, 14 Nov 2022 08:20:47 +0000 (16:20 +0800)]
net: hns3: fix return value check bug of rx copybreak
The refactoring of rx copybreak modifies the original return logic, which
will make this feature unavailable. So this patch fixes the return logic of
rx copybreak.
Fixes: e74a726da2c4 ("net: hns3: refactor hns3_nic_reuse_page()") Fixes: 99f6b5fb5f63 ("net: hns3: use bounce buffer when rx page can not be reused") Signed-off-by: Jie Wang <[email protected]> Signed-off-by: Hao Lan <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
Jian Shen [Mon, 14 Nov 2022 08:20:46 +0000 (16:20 +0800)]
net: hns3: fix incorrect hw rss hash type of rx packet
Currently, the HNS3 driver reports the rss hash type
of each packet based on the rss hash tuples set. It
always reports PKT_HASH_TYPE_L4, without checking the
type of current packet. It's incorrect.
Fixes it by reporting it base on the packet type.
Fixes: 796640778c26 ("net: hns3: support RXD advanced layout") Fixes: 232fc64b6e62 ("net: hns3: Add HW RSS hash information to RX skb") Fixes: ea4858670717 ("net: hns3: handle the BD info on the last BD of the packet") Signed-off-by: Jian Shen <[email protected]> Signed-off-by: Hao Lan <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
Yuan Can [Mon, 14 Nov 2022 02:56:59 +0000 (02:56 +0000)]
net: ena: Fix error handling in ena_init()
The ena_init() won't destroy workqueue created by
create_singlethread_workqueue() when pci_register_driver() failed.
Call destroy_workqueue() when pci_register_driver() failed to prevent the
resource leak.
Cong Wang [Mon, 14 Nov 2022 00:51:19 +0000 (16:51 -0800)]
kcm: close race conditions on sk_receive_queue
sk->sk_receive_queue is protected by skb queue lock, but for KCM
sockets its RX path takes mux->rx_lock to protect more than just
skb queue. However, kcm_recvmsg() still only grabs the skb queue
lock, so race conditions still exist.
We can teach kcm_recvmsg() to grab mux->rx_lock too but this would
introduce a potential performance regression as struct kcm_mux can
be shared by multiple KCM sockets.
So we have to enforce skb queue lock in requeue_rx_msgs() and handle
skb peek case carefully in kcm_wait_data(). Fortunately,
skb_recv_datagram() already handles it nicely and is widely used by
other sockets, we can just switch to skb_recv_datagram() after
getting rid of the unnecessary sock lock in kcm_recvmsg() and
kcm_splice_read(). Side note: SOCK_DONE is not used by KCM sockets,
so it is safe to get rid of this check too.
I ran the original syzbot reproducer for 30 min without seeing any
issue.
platform/x86/amd: pmc: Remove more CONFIG_DEBUG_FS checks
commit b37fe34c8309 ("platform/x86/amd: pmc: remove CONFIG_DEBUG_FS
checks") removed most CONFIG_DEBUG_FS checks, but there were some
left that were reported to cause compile test failures.
Remove the remaining checks, and also the unnecessary CONFIG_SUSPEND
used in the same place.
Linus Walleij [Tue, 15 Nov 2022 08:11:07 +0000 (09:11 +0100)]
pinctrl: mediatek: Export debounce time tables
The kernel test robot complains that in certain combinations
when building the Mediatek drivers as modules we lack some
debounce table symbols, so export them.
Reported-by: kernel test robot <[email protected]> Fixes: e1ff91f9d230 ("pinctrl: mediatek: Fix EINT pins input debounce time configuration") Cc: AngeloGioacchino Del Regno <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
Yuan Can [Sun, 13 Nov 2022 09:29:29 +0000 (09:29 +0000)]
net: ionic: Fix error handling in ionic_init_module()
A problem about ionic create debugfs failed is triggered with the
following log given:
[ 415.799514] debugfs: Directory 'ionic' with parent '/' already present!
The reason is that ionic_init_module() returns ionic_bus_register_driver()
directly without checking its return value, if ionic_bus_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ionic can never be created later.
Amit Cohen [Fri, 11 Nov 2022 17:03:27 +0000 (18:03 +0100)]
mlxsw: Avoid warnings when not offloaded FDB entry with IPv6 is removed
FDB entries that perform VXLAN encapsulation with an IPv6 underlay hold
a reference on a resource - the KVDL entry where the IPv6 underlay
destination IP is stored. For that, the driver maintains two hash tables:
1. Maps IPv6 to KVDL index
2. Maps {MAC, FID index} to IPv6 address
When a FDB entry is removed, the second table is used to find the relevant
IPv6 address and the first table is used to remove the reference count and
free the index if is not used anymore.
In order for a packet to be forwarded to a single remote VTEP, FDB
entries need to be configured at both the bridge and VXLAN devices' FDB
tables. Both entries are squashed into one {MAC, VLAN/VNI} -> IP entry
in the hardware. Therefore, in case one entry is removed, the entry will
be removed from the hardware and the remaining entry will be unmarked
with 'offload' flag since it is not offloaded anymore.
For example, the two FDB entries should be added to allow packets to be
forwarded via vx10:
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff self static dst 2001:db8:5::1
$ bridge fdb add dev vx10 aa:bb:cc:dd:ee:ff master static vlan 10
When one entry will be removed, the second one will not be offloaded
anymore. When the first entry (in VXLAN FDB) will be removed / will not be
offloaded anymore, the two mappings in IPv6 hash tables will be removed.
In case that the second entry is removed before the first one, unexpected
warnings[1][2] will be shown in user space as a result of removing the
first entry. The issue is that not offloaded entry is removed, the driver
tries to search the relevant entries in the hash tables, does not find them
and therefore warns.
Do not handle removing of not offloaded VXLAN FDB entries, as they were
already removed when the offload flag was removed.
Linus Torvalds [Mon, 14 Nov 2022 20:40:51 +0000 (12:40 -0800)]
Merge tag 'vfio-v6.1-rc6' of https://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Fixes for potential container registration leak for drivers not
implementing a close callback, duplicate container de-registrations,
and a regression in support for bus reset on last device close from
a device set (Anthony DeRossi)
* tag 'vfio-v6.1-rc6' of https://github.com/awilliam/linux-vfio:
vfio/pci: Check the device set open count on reset
vfio: Export the device set open count
vfio: Fix container device registration life cycle
Linus Torvalds [Mon, 14 Nov 2022 20:00:03 +0000 (12:00 -0800)]
Merge tag 'mtd/fixes-for-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
- Placate "$VARIABLE is used uninitialized" warnings
- omap2: Add missing dependency on GPMC
- qcom: Handle ret from parse with codeword_fixup
* tag 'mtd/fixes-for-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: onenand: omap2: add dependency on GPMC
mtd: rawnand: placate "$VARIABLE is used uninitialized" warnings
mtd: rawnand: qcom: handle ret from parse with codeword_fixup
Chris Mason [Mon, 14 Nov 2022 18:19:30 +0000 (10:19 -0800)]
blk-cgroup: properly pin the parent in blkcg_css_online
blkcg_css_online is supposed to pin the blkcg of the parent, but 397c9f46ee4d refactored things and along the way, changed it to pin the
css instead. This results in extra pins, and we end up leaking blkcgs
and cgroups.
Jingbo Xu [Mon, 14 Nov 2022 12:19:43 +0000 (20:19 +0800)]
erofs: fix missing xas_retry() in fscache mode
The xarray iteration only holds the RCU read lock and thus may encounter
XA_RETRY_ENTRY if there's process modifying the xarray concurrently.
This will cause oops when referring to the invalid entry.
Fix this by adding the missing xas_retry(), which will make the
iteration wind back to the root node if XA_RETRY_ENTRY is encountered.
pinctrl: mediatek: Fix EINT pins input debounce time configuration
The External Interrupt Controller (EINTC) on all of the supported
MediaTek SoCs does support input debouncing, but not all of them
index the debounce time values (DBNC_SETTING registers) the same way.
Before this change, in some cases, as an example, requesting a debounce
time of 16 milliseconds would mistakenly set the relative DBNC_SETTING
register to 0x2, resulting in a way shorter debounce time of 500uS.
To fix the aforementioned issue, define three different debounce_time
arrays, reflecting the correct register index for each value and for
each register index variant, and make sure that each SoC pinctrl
driver uses the right one.
projects / linux.git / log