Fabio Estevam [Tue, 3 Mar 2015 13:04:45 +0000 (10:04 -0300)]
of/overlay: Remove unused variable
Commit 3e7f7626fd49a ("of/overlay: Do not generate duplicate nodes") removed
the only use of the 'grandchild' variable, which leads to the following build
warning:
drivers/of/overlay.c: In function 'of_overlay_apply_single_device_node':
drivers/of/overlay.c:89:31: warning: unused variable 'grandchild' [-Wunused-variable]
struct device_node *tchild, *grandchild;
^
Chunyan Zhang [Fri, 16 Jan 2015 10:00:07 +0000 (18:00 +0800)]
Documentation: DT: Renamed of-serial.txt to 8250.txt
The file of-serial.txt was only for 8250 compatible UART implementations,
so renamed it to 8250.txt to avoid confusing other persons.
This is suggested by Arnd, see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-September/291455.html
Peter Hurley [Sun, 1 Mar 2015 17:21:22 +0000 (12:21 -0500)]
of: Fix premature bootconsole disable with 'stdout-path'
Support for devicetree serial consoles via 'stdout-path' causes
bootconsoles to be disabled when the vt dummy console loads, since
there is no preferred console (the preferred console is not added
until the device is probed).
Ensure there is at least a preferred console, even if never matched.
Takashi Sakamoto [Tue, 10 Mar 2015 12:54:35 +0000 (21:54 +0900)]
ALSA: firewire-lib: leave unit reference counting completely
With previous commit, this module managed to leave the counting to each
drivers, but the isochronous resources functionality still increment/decrement
the count.
This commit purge such codes to leave the responsibility to each drivers.
Chris Wilson [Fri, 13 Feb 2015 14:35:59 +0000 (14:35 +0000)]
drm/i915: Prevent TLB error on first execution on SNB
Long ago I found that I was getting sporadic errors when booting SNB,
with the symptom being that the first batch died with IPEHR != *ACTHD,
typically caused by the TLB being invalid. These magically disappeared
if I held the forcewake during the entire ring initialisation sequence.
(It can probably be shortened to a short critical section, but the whole
initialisation is full of register writes and so we would be taking and
releasing forcewake almost continually, and so holding it over the
entire sequence will probably be a net win!)
Note some of the kernels I encounted the issue already had the deferred
forcewake release, so it is still relevant.
I know that there have been a few other reports with similar failure
conditions on SNB, I think such as
References: https://bugs.freedesktop.org/show_bug.cgi?id=80913
v2: Wrap i915_gem_init_hw() with its own security blanket as we take
that path following resume and reset.
Mika Kuoppala [Fri, 27 Feb 2015 16:11:09 +0000 (18:11 +0200)]
drm/i915: Do both mt and gen6 style forcewake reset on ivb probe
commit 05a2fb157e44 ("drm/i915: Consolidate forcewake code")
failed to take into account that we have used to reset both
the gen6 style and the multithreaded style forcewake registers.
This is due to fact that ivb can use either, depending on how the
bios has set up the machine.
Mimic the old semantics before we have determined the correct variety
and reset both before the ecobus probe.
Dave Gordon [Fri, 6 Mar 2015 15:34:26 +0000 (15:34 +0000)]
drm/i915: use in_interrupt() not in_irq() to check context
The kernel in_irq() function tests for hard-IRQ context only, so if a
system is run with the kernel 'threadirqs' option selected, the test in
intel_check_page_flip() generates lots of warnings, because then it gets
called in soft-IRQ context.
We can instead use in_interrupt() which allows for either type of
interrupt, while still detecting and complaining about misuse of the
page flip code if it is ever called from non-interrupt context.
Linus Torvalds [Tue, 10 Mar 2015 01:59:50 +0000 (18:59 -0700)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm/s390 bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: non-LPAR case obsolete during facilities mask init
KVM: s390: include guest facilities in kvm facility test
KVM: s390: fix in memory copy of facility lists
KVM: s390/cpacf: Fix kernel bug under z/VM
KVM: s390/cpacf: Enable key wrapping by default
Linus Torvalds [Tue, 10 Mar 2015 01:55:52 +0000 (18:55 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One performance optimization for page_clear and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix incorrect ASCE after crst_table_downgrade
s390/ftrace: fix crashes when switching tracers / add notrace to cpu_relax()
s390/pci: unify pci_iomap symbol exports
s390/pci: fix [un]map_resources sequence
s390: let the compiler do page clearing
s390/pci: fix possible information leak in mmio syscall
s390/dcss: array index 'i' is used before limits check.
s390/scm_block: fix off by one during cluster reservation
s390/jump label: improve and fix sanity check
s390/jump label: add missing jump_label_apply_nops() call
Chris Wilson [Wed, 25 Feb 2015 13:45:26 +0000 (13:45 +0000)]
drm: Don't assign fbs for universal cursor support to files
The internal framebuffers we create to remap legacy cursor ioctls to
plane operations for the universal plane support shouldn't be linke to
the file like normal userspace framebuffers. This bug goes back to the
original universal cursor plane support introduced in
drm: Support legacy cursor ioctls via universal planes when possible (v4)
The isn't too disastrous since fbs are small, we only create one when the
cursor bo gets changed and ultimately they'll be reaped when the window
server restarts.
Conceptually we'd want to just pass NULL for file_priv when creating it,
but the driver needs the file to lookup the underlying buffer object for
cursor id. Instead let's move the file_priv linking out of
add_framebuffer_internal() into the addfb ioctl implementation, which is
the only place it is needed. And also rename the function for a more
accurate since it only creates the fb, but doesn't add it anywhere.
Linus Torvalds [Tue, 10 Mar 2015 01:44:06 +0000 (18:44 -0700)]
Merge tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull seq-buf/ftrace fixes from Steven Rostedt:
"This includes fixes for seq_buf_bprintf() truncation issue. It also
contains fixes to ftrace when /proc/sys/kernel/ftrace_enabled and
function tracing are started. Doing the following causes some issues:
As well as with function tracing too. Pratyush Anand first reported
this issue to me and supplied a patch. When I tested this on my x86
test box, it caused thousands of backtraces and warnings to appear in
dmesg, which also caused a denial of service (a warning for every
function that was listed). I applied Pratyush's patch but it did not
fix the issue for me. I looked into it and found a slight problem
with trampoline accounting. I fixed it and sent Pratyush a patch, but
he said that it did not fix the issue for him.
I later learned tha Pratyush was using an ARM64 server, and when I
tested on my ARM board, I was able to reproduce the same issue as
Pratyush. After applying his patch, it fixed the problem. The above
test uncovered two different bugs, one in x86 and one in ARM and
ARM64. As this looked like it would affect PowerPC, I tested it on my
PPC64 box. It too broke, but neither the patch that fixed ARM or x86
fixed this box (the changes were all in generic code!). The above
test, uncovered two more bugs that affected PowerPC. Again, the
changes were only done to generic code. It's the way the arch code
expected things to be done that was different between the archs. Some
where more sensitive than others.
The rest of this series fixes the PPC bugs as well"
* tag 'trace-fixes-v4.0-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
seq_buf: Fix seq_buf_bprintf() truncation
seq_buf: Fix seq_buf_vprintf() truncation
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
Linus Torvalds [Tue, 10 Mar 2015 01:00:25 +0000 (18:00 -0700)]
Merge tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of driver specific fixes plus a fix for a regression in the
core where the updates to use sysfs group registration were overly
enthusiastic in eliding properties and removed some that had been
previously present"
* tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix regression due to NULL constraints check
regulator: rk808: Set the enable time for LDOs
regulator: da9210: Mask all interrupt sources to deassert interrupt line
Linus Torvalds [Tue, 10 Mar 2015 00:50:02 +0000 (17:50 -0700)]
Merge tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes to which the usual comments
about them being important if you see them mostly apply (except for
the comment fix). The pl022 one is particularly nasty for anyone
affected by it"
* tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pl022: Fix race in giveback() leading to driver lock-up
spi: dw-mid: avoid potential NULL dereference
spi: img-spfi: Verify max spfi transfer length
spi: fix a typo in comment.
spi: atmel: Fix interrupt setup for PDC transfers
spi: dw: revisit FIFO size detection again
spi: dw-pci: correct number of chip selects
drivers: spi: ti-qspi: wait for busy bit clear before data write/read
Linus Torvalds [Tue, 10 Mar 2015 00:45:34 +0000 (17:45 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"fixes for the TPM driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix call order in tpm-chip.c
tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send
Linus Torvalds [Tue, 10 Mar 2015 00:35:29 +0000 (17:35 -0700)]
Merge tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- Fix regression in with omapdss when using i2c displays
- Fix possible null deref in fbmon
- Check kalloc return value in AMBA CLCD
* tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix regression with display sysfs files
video: fbdev: fix possible null dereference
video: ARM CLCD: Add missing error check for devm_kzalloc
Linus Torvalds [Tue, 10 Mar 2015 00:30:09 +0000 (17:30 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"The cgroup iteration update two years ago and the recent cpuset
restructuring introduced regressions in subset of cpuset
configurations. Three patches to fix them.
All are marked for -stable"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: Fix cpuset sched_relax_domain_level
cpuset: fix a warning when clearing configured masks in old hierarchy
cpuset: initialize effective masks when clone_children is enabled
Linus Torvalds [Tue, 10 Mar 2015 00:00:54 +0000 (17:00 -0700)]
Merge branch 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"One fix patch for a subtle livelock condition which can happen on
PREEMPT_NONE kernels involving two racing cancel_work calls. Whoever
comes in the second has to wait for the previous one to finish. This
was implemented by making the later one block for the same condition
that the former would be (work item completion) and then loop and
retest; unfortunately, depending on the wake up order, the later one
could lock out the former one to finish by busy looping on the cpu.
This is fixed by implementing explicit wait mechanism. Work item
might not belong anywhere at this point and there's remote possibility
of thundering herd problem. I originally tried to use bit_waitqueue
but it didn't work for static work items on modules. It's currently
using single wait queue with filtering wake up function and exclusive
wakeup. If this ever becomes a problem, which is not very likely, we
can try to figure out a way to piggy back on bit_waitqueue"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix hang involving racing cancel[_delayed]_work_sync()'s for PREEMPT_NONE
Heikki Krogerus [Fri, 6 Mar 2015 13:48:38 +0000 (15:48 +0200)]
ACPI / LPSS: provide con_id for the clkdev
Commit 7d78cbefaa (serial: 8250_dw: add ability to handle
the peripheral clock) introduces handling for a second clk
to 8250_dw.c which is the driver also for LPSS UART. The
second clk forces us to provide identifier (con_id) for the
clkdev we create.
This fixes an issue where 8250_dw.c is getting the same
handler for both clocks.
Fixes: 7d78cbefaa (serial: 8250_dw: add ability to handle the peripheral clock) Signed-off-by: Heikki Krogerus <[email protected]> Cc: 3.17+ <[email protected]> # 3.17+ Signed-off-by: Rafael J. Wysocki <[email protected]>
Uwe Kleine-König [Sat, 21 Feb 2015 10:40:25 +0000 (11:40 +0100)]
clk: divider: fix calculation of initial best divider when rounding to closest
Similar to the reasoning for the previous commit
DIV_ROUND_CLOSEST(parent_rate, rate)
might not be the best integer divisor to get a good approximation for
rate from parent_rate (given the metric for CLK_DIVIDER_ROUND_CLOSEST).
For example assume a parent rate of 1000 Hz and a target rate of 700.
Using DIV_ROUND_CLOSEST the suggested divisor gets calculated to 1
resulting in a target rate of 1000 with a delta of 300 to the desired
rate. With choosing 2 as divisor however the resulting rate is 500 which
is nearer to 700.
Uwe Kleine-König [Sat, 21 Feb 2015 10:40:24 +0000 (11:40 +0100)]
clk: divider: fix selection of divider when rounding to closest
It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Uwe Kleine-König [Sat, 21 Feb 2015 10:40:23 +0000 (11:40 +0100)]
clk: divider: fix calculation of maximal parent rate for a given divider
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbea2 (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Jon Paul Maloy [Mon, 9 Mar 2015 20:16:22 +0000 (16:16 -0400)]
tipc: fix bug in link failover handling
In commit c637c1035534867b85b78b453c38c495b58e2c5a
("tipc: resolve race problem at unicast message reception") we
introduced a new mechanism for delivering buffers upwards from link
to socket layer.
That code contains a bug in how we handle the new link input queue
during failover. When a link is reset, some of its users may be blocked
because of congestion, and in order to resolve this, we add any pending
wakeup pseudo messages to the link's input queue, and deliver them to
the socket. This misses the case where the other, remaining link also
may have congested users. Currently, the owner node's reference to the
remaining link's input queue is unconditionally overwritten by the
reset link's input queue. This has the effect that wakeup events from
the remaining link may be unduely delayed (but not lost) for a
potentially long period.
We fix this by adding the pending events from the reset link to the
input queue that is currently referenced by the node, whichever one
it is.
This commit should be applied to both net and net-next.
When an interface is deleted from a net namespace the ifindex in the
corresponding entries in PF_PACKET sockets' mclists becomes stale.
This can create inconsistencies if later an interface with the same ifindex
is moved from a different namespace (not that unlikely since ifindexes are
per-namespace).
In particular we saw problems with dev->promiscuity, resulting
in "promiscuity touches roof, set promiscuity failed. promiscuity
feature of device might be broken" warnings and EOVERFLOW failures of
setsockopt(PACKET_ADD_MEMBERSHIP).
This patch deletes the mclist entries for interfaces that are deleted.
Since this now causes setsockopt(PACKET_DROP_MEMBERSHIP) to fail with
EADDRNOTAVAIL if called after the interface is deleted, also make
packet_mc_drop not fail.
David S. Miller [Mon, 9 Mar 2015 19:41:00 +0000 (15:41 -0400)]
Merge tag 'linux-can-fixes-for-4.0-20150309' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-03-09
this is a pull request for net/master for the 4.0 release cycle, it consists of
6 patches:
A patch by Oliver Hartkopp fixes a long outstanding bug in the infrastructure,
which leads to skb_under_panics when CAN interfaces are used by AF_PACKET
sockets e.g. by dhclient. Stephane Grosjean contributes a patch for the
peak_usb driver which adds a missing initialization. Two patches by Ahmed S.
Darwish fix problems in the kvaser_usb driver. Followed by two patches by
myself, updating the MAINTAINERS file
====================
ftrace: Fix ftrace enable ordering of sysctl ftrace_enabled
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.
That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().
Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.
The problem could be seen by the following commands:
Pratyush Anand [Fri, 6 Mar 2015 18:28:06 +0000 (23:58 +0530)]
ftrace: Fix en(dis)able graph caller when en(dis)abling record via sysctl
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().
Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.
# echo 1 > /proc/sys/kernel/ftrace_enabled
Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.
Further if we execute the following after this:
# echo nop > /sys/kernel/debug/tracing/current_tracer
Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.
On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.
Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.
ftrace: Clear REGS_EN and TRAMP_EN flags on disabling record via sysctl
When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.
ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).
When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.
For example, the following will cause ftrace to crash:
As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.
Ahmed S. Darwish [Thu, 26 Feb 2015 15:22:02 +0000 (10:22 -0500)]
can: kvaser_usb: Read all messages in a bulk-in URB buffer
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Ahmed S. Darwish [Thu, 26 Feb 2015 15:20:11 +0000 (10:20 -0500)]
can: kvaser_usb: Avoid double free on URB submission failures
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
can: peak_usb: fix missing ctrlmode_ init for every dev
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Takashi Iwai [Sun, 8 Mar 2015 17:29:50 +0000 (18:29 +0100)]
ALSA: hda - Fix regression of HD-audio controller fallback modes
The commit [63e51fd708f5: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
When reading from the error queue, msg_name and msg_control are only
populated for some errors. A new exception for empty timestamp skbs
added a false positive on icmp errors without payload.
`traceroute -M udpconn` only displayed gateways that return payload
with the icmp error: the embedded network headers are pulled before
sock_queue_err_skb, leaving an skb with skb->len == 0 otherwise.
Fix this regression by refining when msg_name and msg_control
branches are taken. The solutions for the two fields are independent.
msg_name only makes sense for errors that configure serr->port and
serr->addr_offset. Test the first instead of skb->len. This also fixes
another issue. saddr could hold the wrong data, as serr->addr_offset
is not initialized in some code paths, pointing to the start of the
network header. It is only valid when serr->port is set (non-zero).
msg_control support differs between IPv4 and IPv6. IPv4 only honors
requests for ICMP and timestamps with SOF_TIMESTAMPING_OPT_CMSG. The
skb->len test can simply be removed, because skb->dev is also tested
and never true for empty skbs. IPv6 honors requests for all errors
aside from local errors and timestamps on empty skbs.
In both cases, make the policy more explicit by moving this logic to
a new function that decides whether to process msg_control and that
optionally prepares the necessary fields in skb->cb[]. After this
change, the IPv4 and IPv6 paths are more similar.
The last case is rxrpc. Here, simply refine to only match timestamps.
Fixes: 49ca0d8bfaf3 ("net-timestamp: no-payload option") Reported-by: Jan Niehusmann <[email protected]> Signed-off-by: Willem de Bruijn <[email protected]>
----
Changes
v1->v2
- fix local origin test inversion in ip6_datagram_support_cmsg
- make v4 and v6 code paths more similar by introducing analogous
ipv4_datagram_support_cmsg
- fix compile bug in rxrpc Signed-off-by: David S. Miller <[email protected]>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Linus Torvalds [Sun, 8 Mar 2015 19:47:18 +0000 (12:47 -0700)]
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Linus Torvalds [Sun, 8 Mar 2015 19:25:40 +0000 (12:25 -0700)]
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Linus Torvalds [Sun, 8 Mar 2015 19:15:47 +0000 (12:15 -0700)]
Merge tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while"
* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: make device disabled on stop unconditionally
android: binder: fix binder mmap failures
Linus Torvalds [Sun, 8 Mar 2015 18:51:04 +0000 (11:51 -0700)]
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Al Viro [Tue, 3 Mar 2015 08:39:34 +0000 (08:39 +0000)]
gadgetfs: get rid of flipping ->f_op in ep_config()
Final methods start with get_ready_ep(), which will fail unless we have
->state == STATE_EP_ENABLED. So they'd be failing just fine until that
first write() anyway. Let's do the following:
* get_ready_ep() gets a new argument - true when called from
ep_write_iter(), false otherwise.
* make it quiet when it finds STATE_EP_READY (no printk, that is;
the case won't be impossible after that change).
* when that new argument is true, treat STATE_EP_READY the same
way as STATE_EP_ENABLED (i.e. return zero and do not unlock).
* in ep_write_iter(), after success of get_ready_ep() turn
if (!usb_endpoint_dir_in(&epdata->desc)) {
into
if (epdata->state == STATE_EP_ENABLED &&
!usb_endpoint_dir_in(&epdata->desc)) {
- that logics only applies after config.
* have ep_config() take kernel-side buffer (i.e. use memcpy()
instead of copy_from_user() in there) and in the "let's call ep_io or
ep_aio" (again, in ep_write_iter()) add "... or ep_config() in case it's
not configured yet"
Yun Wu [Fri, 6 Mar 2015 16:37:50 +0000 (16:37 +0000)]
irqchip: gicv3-its: Support safe initialization
It's unsafe to change the configurations of an activated ITS directly
since this will lead to unpredictable results. This patch guarantees
the ITSes being initialized are quiescent.
Yun Wu [Fri, 6 Mar 2015 16:37:48 +0000 (16:37 +0000)]
irqchip: gicv3-its: Add limitation to page order
When required size of Device Table is out of the page allocator's
capability, the whole ITS will fail in probing. This actually is
not the hardware's problem and is mainly a limitation of the kernel
page allocator. This patch will keep ITS going on to the next
initializaion stage with an explicit warning.
Yun Wu [Fri, 6 Mar 2015 16:37:47 +0000 (16:37 +0000)]
irqchip: gicv3-its: Use 64KB page as default granule
The field of page size in register GITS_BASERn might be read-only
if an implementation only supports a single, fixed page size. But
currently the ITS driver will throw out an error when PAGE_SIZE
is less than the minimum size supported by an ITS. So addressing
this problem by using 64KB pages as default granule for all the
ITS base tables.
Yun Wu [Fri, 6 Mar 2015 16:37:46 +0000 (16:37 +0000)]
irqchip: gicv3-its: Zero itt before handling to hardware
Some kind of brain-dead implementations chooses to insert ITEes in
rapid sequence of disabled ITEes, and an un-zeroed ITT will confuse
ITS on judging whether an ITE is really enabled or not. Considering
the implementations are still supported by the GICv3 architecture,
in which ITT is not required to be zeroed before being handled to
hardware, we do the favor in ITS driver.
Vladimir Murzin [Fri, 6 Mar 2015 16:37:45 +0000 (16:37 +0000)]
irqchip: gic-v3: Fix out of bounds access to cpu_logical_map
While playing with KASan support for arm64/arm the following appeared on boot:
==================================================================
BUG: AddressSanitizer: out of bounds access in __asan_load8+0x14/0x1c at addr ffffffc000ad0dc0
Read of size 8 by task swapper/0/1
page:ffffffbdc202b400 count:1 mapcount:0 mapping: (null) index:0x0
flags: 0x400(reserved)
page dumped because: kasan: bad access detected
Address belongs to variable __cpu_logical_map+0x200/0x220
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc6-next-20150129+ #481
Hardware name: FVP Base (DT)
Call trace:
[<ffffffc00008a794>] dump_backtrace+0x0/0x184
[<ffffffc00008a928>] show_stack+0x10/0x1c
[<ffffffc00075e46c>] dump_stack+0xa0/0xf8
[<ffffffc0001df490>] kasan_report_error+0x23c/0x264
[<ffffffc0001e0188>] check_memory_region+0xc0/0xe4
[<ffffffc0001dedf0>] __asan_load8+0x10/0x1c
[<ffffffc000431294>] gic_raise_softirq+0xc4/0x1b4
[<ffffffc000091fc0>] smp_send_reschedule+0x30/0x3c
[<ffffffc0000f0d1c>] try_to_wake_up+0x394/0x434
[<ffffffc0000f0de8>] wake_up_process+0x2c/0x6c
[<ffffffc0000d9570>] wake_up_worker+0x38/0x48
[<ffffffc0000dbb50>] insert_work+0xac/0xec
[<ffffffc0000dbd38>] __queue_work+0x1a8/0x374
[<ffffffc0000dbf60>] queue_work_on+0x5c/0x7c
[<ffffffc0000d8a78>] call_usermodehelper_exec+0x170/0x188
[<ffffffc0004037b8>] kobject_uevent_env+0x650/0x6bc
[<ffffffc000403830>] kobject_uevent+0xc/0x18
[<ffffffc00040292c>] kset_register+0xa8/0xc8
[<ffffffc0004d6c88>] bus_register+0x134/0x2e8
[<ffffffc0004d73b4>] subsys_virtual_register+0x2c/0x5c
[<ffffffc000a76a4c>] wq_sysfs_init+0x14/0x20
[<ffffffc000082a28>] do_one_initcall+0xa8/0x1fc
[<ffffffc000a70db4>] kernel_init_freeable+0x1ec/0x294
[<ffffffc00075aa5c>] kernel_init+0xc/0xec
Memory state around the buggy address: ffffff80003e0820: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffff80003e0830: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffff80003e0840: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
^ ffffff80003e0850: 00 00 fa fa fa fa fa fa 00 00 00 00 00 00 00 00
==================================================================
The reason for that cpumask_next() returns >= nr_cpu_ids if no further cpus
set, but "==" condition is checked only, so we end up with out-of-bounds
access to cpu_logical_map.
Fix is by using the condition check for cpumask_next.
Marc Zyngier [Fri, 6 Mar 2015 16:37:42 +0000 (16:37 +0000)]
irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration
The current PCI/MSI support in the GICv3 ITS doesn't really deal
with systems where different PCI devices end-up using the same
RequesterID (as it would be the case with non-transparent bridges,
for example). It is likely that none of these devices would
actually generate any interrupt, as the ITS is programmed with
the device's own ID, and not that of the bridge.
A solution to this is to iterate over the PCI hierarchy to
discover what the device aliases too. We also use this
to discover the upper bound of the number of MSIs that this
sub-hierarchy can generate.
Marc Zyngier [Fri, 6 Mar 2015 16:37:41 +0000 (16:37 +0000)]
irqchip: gicv3-its: Allocate enough memory for the full range of DeviceID
The ITS table allocator is only allocating a single page per table.
This works fine for most things, but leads to silent lack of
interrupt delivery if we end-up with a device that has an ID that is
out of the range defined by a single page of memory. Even worse, depending
on the page size, behaviour changes, which is not a very good experience.
A solution is actually to allocate memory for the full range of ID that
the ITS supports. A massive waste memory wise, but at least a safe bet.
Vladimir Murzin [Fri, 6 Mar 2015 16:37:40 +0000 (16:37 +0000)]
irqchip: gicv3-its: Fix ITS CPU init
We skip initialisation of ITS in case the device-tree has no
corresponding description, but we are still accessing to ITS bits while
setting CPU interface what leads to the kernel panic:
It happens in gic_rdists_supports_plpis() because gic_rdists is NULL.
The gic_rdists is set to non-NULL only when ITS node is presented in
the device-tree.
Fix this by moving the call to gic_rdists_supports_plpis() inside the
!list_empty(&its_nodes) block, because it is that list that guards the
validity of the rest of the information in this driver.
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
Input: psmouse - disable "palm detection" in the focaltech driver
Apparently, the threshold for large contact area seems to be rather low on
some devices, causing the touchpad to frequently freeze during normal
usage. Because we do now know how we are supposed to use the value in
question, this commit just drops the related code completely.
Input: psmouse - disable changing resolution/rate/scale for FocalTech
These PS/2 commands make some touchpads stop responding, so this commit
adds some dummy functions to replace the generic implementation. Because
scale changes were not encapsulated in a method of struct psmouse yet, this
commit adds a method set_scale to psmouse.
Input: psmouse - ensure that focaltech reports consistent coordinates
We don't know whether x_max or y_max really hold the maximum possible
coordinates, and we don't know for sure whether we correctly interpret the
coordinates sent by the touchpad, so we clamp the reported values to
prevent confusion in userspace code.
Linus Torvalds [Sat, 7 Mar 2015 19:31:17 +0000 (11:31 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"arm64 and generic kernel/module.c (acked by Rusty) fixes for
CONFIG_DEBUG_SET_MODULE_RONX"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
kernel/module.c: Update debug alignment after symtable generation
arm64: Don't use is_module_addr in setting page attributes
It's directly caused by 89d3cf6 [SCSI] libsas: add mutex for SMP task
execution, but shows a deeper cause: expander functions expect to be able to
cast to and treat domain devices as expanders. The correct fix is to only do
expander discover when we know we've got an expander device to avoid wrongly
casting a non-expander device.
Johan Hovold [Wed, 4 Mar 2015 09:39:07 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent maximum timeout
Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.
Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.
Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Johan Hovold [Wed, 4 Mar 2015 09:39:06 +0000 (10:39 +0100)]
TTY: fix tty_wait_until_sent on 64-bit machines
Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.
This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.
The first symptom was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.
Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.
Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.
Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Peter Hurley [Sun, 1 Mar 2015 15:24:28 +0000 (10:24 -0500)]
serial: uapi: Declare all userspace-visible io types
ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.
Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Peter Hurley [Sun, 1 Mar 2015 15:18:16 +0000 (10:18 -0500)]
serial: core: Fix iotype userspace breakage
commit 3ffb1a8193bea ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.
Peter Hurley [Sun, 1 Mar 2015 15:11:05 +0000 (10:11 -0500)]
console: Fix console name size mismatch
commit 6ae9200f2cab7 ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.
But it still misses one point. As John Paul correctly points out, we
do not care about setting date. If somebody ever changes wall
time backwards (by mistake for example), tty timestamps are never
updated until the original wall time passes.
So check the absolute difference of times and if it large than "8
seconds or so", always update the time. That means we will update
immediatelly when changing time. Ergo, CAP_SYS_TIME can foul the
check, but it was always that way.
Thanks John for serving me this so nicely debugged.
Desmond Liu [Fri, 27 Feb 2015 00:35:57 +0000 (16:35 -0800)]
serial: 8250_dw: Fix get_mctrl behaviour
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
The conditional RX-FIFO read seems to cause spurious interrupts and we
see just:
|serial8250: too much work for irq29
The previous behaviour was "default" for decades and Marvell's 88f6282 SoC
might not be the only that relies on it. Therefore the Omap fix is
reverted for now.
Fixes: 0aa525d11859 ("tty: serial: 8250_core: read only RX if there is
something in the FIFO") Reported-By: Nicolas Schichan <[email protected]> Debuged-By: Peter Hurley <[email protected]> Signed-off-by: Sebastian Andrzej Siewior <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
Linus Torvalds [Sat, 7 Mar 2015 00:54:22 +0000 (16:54 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon, imx, msm, and i915 fixes.
The msm, imx and i915 ones are fairly run of the mill.
Radeon had some DP audio and posting reads for irq fixes, along with a
fix for 32-bit kernels with new cards, we were using unsigned long to
represent GPU side memory space, but since that changed size on 32 vs
64 cards with lots of VRAM failed, so the change has no effect on
x86-64, just moves to using uint64_t instead"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/msm: kexec fixes
drm/msm/mdp5: fix cursor blending
drm/msm/mdp5: fix cursor ROI
drm/msm/atomic: Don't leak atomic commit object when commit fails
drm/msm/mdp5: Avoid flushing registers when CRTC is disabled
drm/msm: update generated headers (add 6th lm.base entry)
drm/msm/mdp5: fixup "drm/msm: fix fallout of atomic dpms changes"
drm/ttm: device address space != CPU address space
drm/mm: Support 4 GiB and larger ranges
drm/i915: gen4: work around hang during hibernation
drm/i915: Check for driver readyness before handling an underrun interrupt
drm/radeon: fix interlaced modes on DCE8
drm/radeon: fix DRM_IOCTL_RADEON_CS oops
drm/radeon: do a posting read in cik_set_irq
drm/radeon: do a posting read in si_set_irq
drm/radeon: do a posting read in evergreen_set_irq
drm/radeon: do a posting read in r600_set_irq
drm/radeon: do a posting read in rs600_set_irq
drm/radeon: do a posting read in r100_set_irq
radeon/audio: fix DP audio on DCE6
...
This patch marks baytrail_i2c_acquire() that it might sleep. Also it chages
while-loop to do-while and, though it is matter of taste, gives a chance to
check one more time before report a timeout.
Andy Shevchenko [Tue, 10 Feb 2015 17:06:08 +0000 (19:06 +0200)]
i2c: designware-baytrail: fix sparse warnings
There is no need to export functions that are used as the callbacks in the
struct dw_i2c_dev. Otherwise we get the following warnings:
drivers/i2c/busses/i2c-designware-baytrail.c:63:5: warning: symbol 'baytrail_i2c_acquire' was not declared. Should it be static?
drivers/i2c/busses/i2c-designware-baytrail.c:114:6: warning: symbol 'baytrail_i2c_release' was not declared. Should it be static?
While here, do few indentation fixes, remove i2c_dw_eval_lock_support() from
functions exported to the modules and redundant assignment of local sem
variable.
Andy Shevchenko [Tue, 10 Feb 2015 17:06:07 +0000 (19:06 +0200)]
i2c: designware-baytrail: fix typo in error path
It seems we have same message for different return values in get_sem() and
baytrail_i2c_acquire(). I suspect this is just a typo, so this patch fixes it.
Linus Torvalds [Fri, 6 Mar 2015 21:52:54 +0000 (13:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Outside of misc fixes, Filipe has a few fsync corners and we're
pulling in one more of Josef's fixes from production use here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs:__add_inode_ref: out of bounds memory read when looking for extended ref.
Btrfs: fix data loss in the fast fsync path
Btrfs: remove extra run_delayed_refs in update_cowonly_root
Btrfs: incremental send, don't rename a directory too soon
btrfs: fix lost return value due to variable shadowing
Btrfs: do not ignore errors from btrfs_lookup_xattr in do_setxattr
Btrfs: fix off-by-one logic error in btrfs_realloc_node
Btrfs: add missing inode update when punching hole
Btrfs: abort the transaction if we fail to update the free space cache inode
Btrfs: fix fsync race leading to ordered extent memory leaks
projects / linux.git / log