In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1077614 ("Missing break in switch") Signed-off-by: Gustavo A. R. Silva <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Correct the formula for calculating the RQ page remainder,
which should be in byte granularity. The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.
Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.
VSC8584 supports 4 LEDs while VSC8531 only supports 2. Let's factorize
the documentation for LED mode properties and give the 4 default values
(the first two being shared between VSC8531 and VSC8584).
net: phy: mscc: factorize function for getting LED mode from DT
Microsemi PHYs support different LED modes depending on the variant, so
let's factorize the code so we just have to give the supported modes
while the logic behind getting the mode remains identical.
David S. Miller [Tue, 4 Sep 2018 05:12:02 +0000 (22:12 -0700)]
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
In the previous implement, the query operation for fibre port and copper
port are mixed. This patch refines it by seperating them based on the port
type.
net: hns3: Remove redundant codes of query advertised flow control abilitiy
If the advertised flow control ability has been fetched using
phy_ethtool_ksettings_get() or hclge_get_link_mode() then it is
unnecessary to fetch them again later using hclge_get_flowctrl_adv().
This patch removes it.
Yunsheng Lin [Mon, 3 Sep 2018 10:21:54 +0000 (11:21 +0100)]
net: hns3: Change the dst mac addr of loopback packet
Currently, the dst mac addr of loopback packet is the same as
the host' mac addr, the SSU component may loop back the packet
to host before the packet reaches mac or serdes, which will defect
the purpose of mac or serdes selftest.
This patch changes it by adding 0x1f to the last byte of dst mac
addr.
Yunsheng Lin [Mon, 3 Sep 2018 10:21:53 +0000 (11:21 +0100)]
net: hns3: Only update mac configuation when necessary
Currently only fiber port checks if it is necessay to set the
mac through firmware when link is changed, this patch unify the
checking to allow the copper port do the checking too.
Yunsheng Lin [Mon, 3 Sep 2018 10:21:52 +0000 (11:21 +0100)]
net: hns3: Preserve vlan 0 in hardware table
When netdev is down, the stack will delete the vlan from
hardware including vlan0, which will cause problem when
doing loopback selftest when netdev is down.
This patch fixes it by always preserving vlan 0 in hardware,
because vlan 0 is defalut vlan, which should always be in
hardware.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yunsheng Lin <[email protected]> Signed-off-by: Peng Li <[email protected]> Signed-off-by: Salil Mehta <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Yunsheng Lin [Mon, 3 Sep 2018 10:21:51 +0000 (11:21 +0100)]
net: hns3: Fix ping exited problem when doing lp selftest
When ping is runnig and user executes the loopback selftest, the
ping cmd will stop and exit.
This patch fixes it by using the hns3_nic_net_open/stop to offline
the netdev when doing loopback selftest.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yunsheng Lin <[email protected]> Signed-off-by: Peng Li <[email protected]> Signed-off-by: Salil Mehta <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Yunsheng Lin [Mon, 3 Sep 2018 10:21:50 +0000 (11:21 +0100)]
net: hns3: Fix for loopback selftest failed problem
Tqp and mac need to be enabled when doing loopback selftest,
ae_algo->ops->start/stop is used to do the job, there is a
time window between ae_algo->ops->start/stop and loopback setup,
which will cause selftest failed problem when there is frame
coming in during that time window.
This patch fixes it by enabling the tqp and mac during loopback
setup process.
Fixes: c39c4d98dc65 ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yunsheng Lin <[email protected]> Signed-off-by: Peng Li <[email protected]> Signed-off-by: Salil Mehta <[email protected]> Signed-off-by: David S. Miller <[email protected]>
PF uses hdev->vlan_table to manage the port vlan table. In function
hclge_set_vlan_filter_hw(), it checks whether a vlan id has been used,
by foreach all the vport bits. It should use macro HCLGE_VPORT_NUM,
not VLAN_N_VID as the foreach condition.
Huazhong Tan [Mon, 3 Sep 2018 10:21:47 +0000 (11:21 +0100)]
net: hns3: Fix for multicast failure
When the lower 24 bits of the IPV6 link-local addresses at both
ends are the same, the multicast MAC address for Neigbour Discovery
is the same. The multicast for Neigbour Discovery will fail.
This patch fixes it by including the bonding uplink port in the
multicast group.
Fixes: 46a3df9f9718("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Huazhong Tan <[email protected]> Signed-off-by: Peng Li <[email protected]> Signed-off-by: Salil Mehta <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Yunsheng Lin [Mon, 3 Sep 2018 10:21:46 +0000 (11:21 +0100)]
net: hns3: Fix for vf vlan delete failed problem
There are only 128 entries in vf vlan table, if user has added
more than 128 vlan, fw will ignore it and disable the vf vlan
table. So when user deletes the vlan entry that has not been
set to vf vlan table, fw will return not found result and driver
treat that as error, which will cause vlan delete failed problem.
This patch fixes it by returning ok when fw returns not found
result.
Fixes: 6c251711b37f ("net: hns3: Disable vf vlan filter when vf vlan table is full") Signed-off-by: Yunsheng Lin <[email protected]> Signed-off-by: Peng Li <[email protected]> Signed-off-by: Salil Mehta <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Mon, 3 Sep 2018 08:23:19 +0000 (04:23 -0400)]
bnxt_en: Do not adjust max_cp_rings by the ones used by RDMA.
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea506 ("bnxt_en: Add ULP calls to stop and restart IRQs.") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Mon, 3 Sep 2018 08:23:17 +0000 (04:23 -0400)]
bnxt_en: Fix firmware signaled resource change logic in open.
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b92b ("bnxt_en: Notify firmware about IF state changes.") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Xin Long [Mon, 3 Sep 2018 07:47:11 +0000 (15:47 +0800)]
sctp: not traverse asoc trans list if non-ipv6 trans exists for ipv6_flowlabel
When users set params.spp_address and get a trans, ipv6_flowlabel flag
should be applied into this trans. But even if this one is not an ipv6
trans, it should not go to apply it into all other transes of the asoc
but simply ignore it.
Fixes: 0b0dce7a36fb ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams") Signed-off-by: Xin Long <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Xin Long [Mon, 3 Sep 2018 07:47:10 +0000 (15:47 +0800)]
sctp: fix invalid reference to the index variable of the iterator
Now in sctp_apply_peer_addr_params(), if SPP_IPV6_FLOWLABEL flag is set
and trans is NULL, it would use trans as the index variable to traverse
transport_addr_list, then trans is set as the last transport of it.
Later, if SPP_DSCP flag is set, it would enter into the wrong branch as
trans is actually an invalid reference.
So fix it by using a new index variable to traverse transport_addr_list
for both SPP_DSCP and SPP_IPV6_FLOWLABEL flags process.
Fixes: 0b0dce7a36fb ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams") Reported-by: Julia Lawall <[email protected]> Signed-off-by: Xin Long <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Ivan Mikhaylov [Mon, 3 Sep 2018 07:26:28 +0000 (10:26 +0300)]
net/ibm/emac: wrong emac_calc_base call was used by typo
__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.
Fixes: 45d6e545505fd32edb812f085be7de45b6a5c0af ("net/ibm/emac: add 8192 rx/tx fifo size") Signed-off-by: Ivan Mikhaylov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: sched: null actions array pointer before releasing action
Currently, tcf_action_delete() nulls actions array pointer after putting
and deleting it. However, if tcf_idr_delete_index() returns an error,
pointer to action is not set to null. That results it being released second
time in error handling code of tca_action_gd().
Kasan error:
[ 807.367755] ==================================================================
[ 807.375844] BUG: KASAN: use-after-free in tc_setup_cb_call+0x14e/0x250
[ 807.382763] Read of size 8 at addr ffff88033e636000 by task tc/2732
[ 807.958240] Memory state around the buggy address:
[ 807.963405] ffff88033e635f00: fc fc fc fc fb fb fb fb fb fb fb fc fc fc fc fb
[ 807.971288] ffff88033e635f80: fb fb fb fb fb fb fc fc fc fc fc fc fc fc fc fc
[ 807.979166] >ffff88033e636000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 807.994882] ^
[ 807.998477] ffff88033e636080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 808.006352] ffff88033e636100: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
[ 808.014230] ==================================================================
[ 808.022108] Disabling lock debugging due to kernel taint
Fixes: edfaf94fa705 ("net_sched: improve and refactor tcf_action_put_many()") Signed-off-by: Vlad Buslov <[email protected]> Acked-by: Cong Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
The _IOC_READ flag fits this ioctl request more because this request
actually only writes to, but doesn't read from userspace.
See NOTEs in include/uapi/asm-generic/ioctl.h for more information.
Hangbin Liu [Fri, 31 Aug 2018 08:52:01 +0000 (16:52 +0800)]
ip6_tunnel: respect ttl inherit for ip6tnl
man ip-tunnel ttl section says:
0 is a special value meaning that packets inherit the TTL value.
IPv4 tunnel respect this in ip_tunnel_xmit(), but IPv6 tunnel has not
implement it yet. To make IPv6 behave consistently with IP tunnel,
add ipv6 tunnel inherit support.
mac80211: don't Tx a deauth frame if the AP forbade Tx
If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.
Make sure that we don't send the deauthentication frame in
this case.
In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.
Ilan Peer [Fri, 31 Aug 2018 08:31:10 +0000 (11:31 +0300)]
mac80211: Fix station bandwidth setting after channel switch
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
mac80211: fix a race between restart and CSA flows
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Dreyfuss, Haim [Fri, 31 Aug 2018 08:31:04 +0000 (11:31 +0300)]
mac80211: fix WMM TXOP calculation
In commit 9236c4523e5b ("mac80211: limit wmm params to comply
with ETSI requirements"), we have limited the WMM parameters to
comply with 802.11 and ETSI standard. Mistakenly the TXOP value
was caluclated wrong. Fix it by taking the minimum between
802.11 to ETSI to make sure we are not violating both.
Fixes: e552af058148 ("mac80211: limit wmm params to comply with ETSI requirements") Signed-off-by: Haim Dreyfuss <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
Dan Carpenter [Fri, 31 Aug 2018 08:10:55 +0000 (11:10 +0300)]
cfg80211: fix a type issue in ieee80211_chandef_to_operating_class()
The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we
are truncating away the high bits. I noticed this bug because in commit 9cf0a0b4b64a ("cfg80211: Add support for 60GHz band channels 5 and 6")
we made "freq <= 56160 + 2160 * 6" a valid requency when before it was
only "freq <= 56160 + 2160 * 4" that was valid. It introduces a static
checker warning:
Lorenzo Bianconi [Thu, 30 Aug 2018 23:04:13 +0000 (01:04 +0200)]
mac80211: fix an off-by-one issue in A-MSDU max_subframe computation
Initialize 'n' to 2 in order to take into account also the first
packet in the estimation of max_subframe limit for a given A-MSDU
since frag_tail pointer is NULL when ieee80211_amsdu_aggregate
routine analyzes the second frame.
Fixes: 6e0456b54545 ("mac80211: add A-MSDU tx support") Signed-off-by: Lorenzo Bianconi <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
Merge tag 'dma-mapping-4.19-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few fixes for the fallout of being a little more pedantic about dma
masks"
* tag 'dma-mapping-4.19-2' of git://git.infradead.org/users/hch/dma-mapping:
of/platform: initialise AMBA default DMA masks
sparc: set a default 32-bit dma mask for OF devices
kernel/dma/direct: take DMA offset into account in dma_direct_supported
net/mlx5e: IPoIB, Add ndo stats support for IPoIB netdevices
Expose RX and TX counters by implementing ndo_get_stats64 operation for
both parent devices.
After this change, all the relevant statistics can be retrieved using
ifconfig.
net/mlx5e: IPoIB, Initialize max_opened_tc in mlx5i_init flow
Enhanced ipoib does not initialize max_opened_tc causing wrong ethtool
statistics. As mlx5e_grp_sw_update_stats relies on this variable, without
this change, the TX statistics will not be updated.
Fixes: 05909babce53 ("net/mlx5e: Avoid reset netdev stats on configuration changes") Signed-off-by: Feras Daoud <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]> Signed-off-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Sun, 2 Sep 2018 23:16:24 +0000 (16:16 -0700)]
Merge branch 'Full-phylink-support-for-mv88e6352'
Andrew Lunn says:
====================
Full phylink support for mv88e6352
These two patches implement full phylink support for the mv88e6352
family, when using an SFP connected to its SERDES interface. This adds
interrupt support to the SERDES, so that we get interrupts on link
up/down, and then make calls phydev_link_change().
The first patch is a minor bug fix, which does not seem to affect any
current features, so i'm not submitting it for stable. It is however
required for configuring SERDES interrupts.
====================
Andrew Lunn [Sun, 2 Sep 2018 16:13:15 +0000 (18:13 +0200)]
net: dsa: mv88e6xxx: Add SERDES phydev_link_change for 6352
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Andrew Lunn [Sun, 2 Sep 2018 16:13:14 +0000 (18:13 +0200)]
net: dsa: mv88e6xxx: Fix writing to a PHY page.
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f14 ("net: dsa: mv88e6xxx: describe PHY page and SerDes") Signed-off-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
/usr/include/linux/rds.h:156:18: error: field ‘laddr’ has incomplete type
struct in6_addr laddr;
^~~~~
/usr/include/linux/rds.h:157:18: error: field ‘faddr’ has incomplete type
struct in6_addr faddr;
^~~~~
/usr/include/linux/rds.h:178:18: error: field ‘laddr’ has incomplete type
struct in6_addr laddr;
^~~~~
/usr/include/linux/rds.h:179:18: error: field ‘faddr’ has incomplete type
struct in6_addr faddr;
^~~~~
/usr/include/linux/rds.h:198:18: error: field ‘bound_addr’ has incomplete type
struct in6_addr bound_addr;
^~~~~~~~~~
/usr/include/linux/rds.h:199:18: error: field ‘connected_addr’ has incomplete type
struct in6_addr connected_addr;
^~~~~~~~~~~~~~
/usr/include/linux/rds.h:219:18: error: field ‘local_addr’ has incomplete type
struct in6_addr local_addr;
^~~~~~~~~~
/usr/include/linux/rds.h:221:18: error: field ‘peer_addr’ has incomplete type
struct in6_addr peer_addr;
^~~~~~~~~
/usr/include/linux/rds.h:245:18: error: field ‘src_addr’ has incomplete type
struct in6_addr src_addr;
^~~~~~~~
/usr/include/linux/rds.h:246:18: error: field ‘dst_addr’ has incomplete type
struct in6_addr dst_addr;
^~~~~~~~
Fixes: b7ff8b1036f0 ("rds: Extend RDS API for IPv6 support") Signed-off-by: Vinson Lee <[email protected]> Acked-by: Santosh Shilimkar <[email protected]> Signed-off-by: David S. Miller <[email protected]>
tcp: remove useless add operation when init sysctl_max_tw_buckets
cp_hashinfo.ehash_mask is always an odd number, which is set in function
alloc_large_system_hash(). See bellow,
if (_hash_mask)
*_hash_mask = (1 << log2qty) - 1; <<< always odd number
Hence the local variable 'cnt' is a even number, as a result of that it is
no difference to do the incrementation here.
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix one remaining buggy offset override in sockmap's bpf_msg_pull_data()
when linearizing multiple scatterlist elements, from Tushar.
2) Fix BPF sockmap's misuse of ULP when a collision with another ULP is
found on map update where it would release existing ULP. syzbot found and
triggered this couple of times now, fix from John.
3) Add missing xskmap type to bpftool so it will properly show the type
on map dump, from Prashant.
====================
David S. Miller [Sun, 2 Sep 2018 21:13:31 +0000 (14:13 -0700)]
Merge branch 'mvneta-some-small-improvements'
Jisheng Zhang says:
====================
net: mvneta: some small improvements
patch1 removes the NETIF_F_GRO check ourself, because the net subsystem
will handle it for us.
patch2 enables NETIF_F_RXCSUM by default, since the driver and HW
supports the feature.
patch3 is a small optimization, to reduce smp_processor_id() calling
in mvneta_tx_done_gbe.
since v1:
- based on net-next tree
- remove the fix patches, since they should be based on net branch.
- Add Gregory's Reviewed-by tag
====================
After the patch, the loop looks like(under arm64):
...
bl 0 <_raw_spin_lock>
str w23, [x28,#132]
...
where w23 is loaded so be ready before the loop.
>From another side, mvneta_tx_done_gbe() is called from mvneta_poll()
which is in non-preemptible context, so it's safe to call the
smp_processor_id() function once.
Jisheng Zhang [Fri, 31 Aug 2018 08:09:13 +0000 (16:09 +0800)]
net: mvneta: Don't check NETIF_F_GRO ourself
napi_gro_receive() checks NETIF_F_GRO bit as well, if the bit is not
set, we will go through GRO_NORMAL in napi_skb_finish(), so fall back
to netif_receive_skb_internal(), so we don't need to check NETIF_F_GRO
ourself.
David Ahern [Thu, 30 Aug 2018 21:15:43 +0000 (14:15 -0700)]
net/ipv6: Only update MTU metric if it set
Jan reported a regression after an update to 4.18.5. In this case ipv6
default route is setup by systemd-networkd based on data from an RA. The
RA contains an MTU of 1492 which is used when the route is first inserted
but then systemd-networkd pushes down updates to the default route
without the mtu set.
Prior to the change to fib6_info, metrics such as MTU were held in the
dst_entry and rt6i_pmtu in rt6_info contained an update to the mtu if
any. ip6_mtu would look at rt6i_pmtu first and use it if set. If not,
the value from the metrics is used if it is set and finally falling
back to the idev value.
After the fib6_info change metrics are contained in the fib6_info struct
and there is no equivalent to rt6i_pmtu. To maintain consistency with
the old behavior the new code should only reset the MTU in the metrics
if the route update has it set.
Fixes: d4ead6b34b67 ("net/ipv6: move metrics from dst to rt6_info") Reported-by: Jan Janssen <[email protected]> Signed-off-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Tony Lindgren [Wed, 29 Aug 2018 15:00:24 +0000 (08:00 -0700)]
net: ethernet: cpsw-phy-sel: prefer phandle for phy sel
The cpsw-phy-sel device is not a child of the cpsw interconnect target
module. It lives in the system control module.
Let's fix this issue by trying to use cpsw-phy-sel phandle first if it
exists and if not fall back to current usage of trying to find the
cpsw-phy-sel child. That way the phy sel driver can be a child of the
system control module where it belongs in the device tree.
Without this fix, we cannot have a proper interconnect target module
hierarchy in device tree for things like genpd.
Note that deferred probe is mostly not supported by cpsw and this patch
does not attempt to fix that. In case deferred probe support is needed,
this could be added to cpsw_slave_open() and phy_connect() so they start
handling and returning errors.
For documenting it, looks like the cpsw-phy-sel is used for all cpsw device
tree nodes. It's missing the related binding documentation, so let's also
update the binding documentation accordingly.
Tony Lindgren [Wed, 29 Aug 2018 15:00:23 +0000 (08:00 -0700)]
dt-bindings: net: cpsw: Document cpsw-phy-sel usage but prefer phandle
The current cpsw usage for cpsw-phy-sel is undocumented but is used for
all the boards using cpsw. And cpsw-phy-sel is not really a child of
the cpsw device, it lives in the system control module instead.
Let's document the existing usage, and improve it a bit where we prefer
to use a phandle instead of a child device for it. That way we can
properly describe the hardware in dts files for things like genpd.
Hangbin Liu [Wed, 29 Aug 2018 10:06:10 +0000 (18:06 +0800)]
igmp: fix incorrect unsolicit report count after link down and up
After link down and up, i.e. when call ip_mc_up(), we doesn't init
im->unsolicit_count. So after igmp_timer_expire(), we will not start
timer again and only send one unsolicit report at last.
Fix it by initializing im->unsolicit_count in igmp_group_added(), so
we can respect igmp robustness value.
Fixes: 24803f38a5c0b ("igmp: do not remove igmp souce list info when set link down") Signed-off-by: Hangbin Liu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Hangbin Liu [Wed, 29 Aug 2018 10:06:08 +0000 (18:06 +0800)]
igmp: fix incorrect unsolicit report count when join group
We should not start timer if im->unsolicit_count equal to 0 after decrease.
Or we will send one more unsolicit report message. i.e. 3 instead of 2 by
default.
Fixes: 1da177e4c3f41 ("Linux-2.6.12-rc2") Signed-off-by: Hangbin Liu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
John Fastabend [Fri, 31 Aug 2018 04:25:02 +0000 (21:25 -0700)]
bpf: avoid misuse of psock when TCP_ULP_BPF collides with another ULP
Currently we check sk_user_data is non NULL to determine if the sk
exists in a map. However, this is not sufficient to ensure the psock
or the ULP ops are not in use by another user, such as kcm or TLS. To
avoid this when adding a sock to a map also verify it is of the
correct ULP type. Additionally, when releasing a psock verify that
it is the TCP_ULP_BPF type before releasing the ULP. The error case
where we abort an update due to ULP collision can cause this error
path.
For example,
__sock_map_ctx_update_elem()
[...]
err = tcp_set_ulp_id(sock, TCP_ULP_BPF) <- collides with TLS
if (err) <- so err out here
goto out_free
[...]
out_free:
smap_release_sock() <- calling tcp_cleanup_ulp releases the
TLS ULP incorrectly.
Fixes: 2f857d04601a ("bpf: sockmap, remove STRPARSER map_flags and add multi-map support") Signed-off-by: John Fastabend <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
Tushar Dave [Fri, 31 Aug 2018 21:45:16 +0000 (23:45 +0200)]
bpf: Fix bpf_msg_pull_data()
Helper bpf_msg_pull_data() mistakenly reuses variable 'offset' while
linearizing multiple scatterlist elements. Variable 'offset' is used
to find first starting scatterlist element
i.e. msg->data = sg_virt(&sg[first_sg]) + start - offset"
Use different variable name while linearizing multiple scatterlist
elements so that value contained in variable 'offset' won't get
overwritten.
Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data") Signed-off-by: Tushar Dave <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"First batch of fixes post-merge window:
- A handful of devicetree changes for i.MX2{3,8} to change over to
new panel bindings. The platforms were moved from legacy
framebuffers to DRM and some development board panels hadn't yet
been converted.
- OMAP fixes related to ti-sysc driver conversion fallout, fixing
some register offsets, no_console_suspend fixes, etc.
- Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.
- Fixed 0755->0644 permissions on a newly added file.
- Defconfig changes to make ARM Versatile more useful with QEMU
(helps testing).
- Enable defconfig options for new TI SoC platform that was merged
this window (AM6)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: Enable TI's AM6 SoC platform
ARM: defconfig: Update the ARM Versatile defconfig
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Speculation:
- Make the microcode check more robust
- Make the L1TF memory limit depend on the internal cache physical
address space and not on the CPUID advertised physical address
space, which might be significantly smaller. This avoids disabling
L1TF on machines which utilize the full physical address space.
- Fix the GDT mapping for EFI calls on 32bit PTI
- Fix the MCE nospec implementation to prevent #GP
Fixes and robustness:
- Use the proper operand order for LSL in the VDSO
- Prevent NMI uaccess race against CR3 switching
- Add a lockdep check to verify that text_mutex is held in
text_poke() functions
- Repair the fallout of giving native_restore_fl() a prototype
- Prevent kernel memory dumps based on usermode RIP
- Wipe KASAN shadow stack before rewinding the stack to prevent false
positives
- Move the AMS GOTO enforcement to the actual build stage to allow
user API header extraction without a compiler
- Fix a section mismatch introduced by the on demand VDSO mapping
change
Miscellaneous:
- Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Fix section mismatch warning/error
x86/vdso: Fix lsl operand order
x86/mce: Fix set_mce_nospec() to avoid #GP fault
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
x86/nmi: Fix NMI uaccess race against CR3 switching
x86: Allow generating user-space headers without a compiler
x86/dumpstack: Don't dump kernel memory based on usermode RIP
x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
x86/irqflags: Mark native_restore_fl extern inline
x86/build: Remove jump label quirk for GCC older than 4.5.2
x86/Kconfig: Fix trivial typo
x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
x86/spectre: Add missing family 6 check to microcode check
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"A small set of updates for core code:
- Prevent tracing in functions which are called from trace patching
via stop_machine() to prevent executing half patched function trace
entries.
- Remove old GCC workarounds
- Remove pointless includes of notifier.h"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Remove workaround for unreachable warnings from old GCC
notifier: Remove notifier header file wherever not used
watchdog: Mark watchdog touch functions as notrace
Randy Dunlap [Sun, 2 Sep 2018 04:01:28 +0000 (21:01 -0700)]
x86/pti: Fix section mismatch warning/error
Fix the section mismatch warning in arch/x86/mm/pti.c:
WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.
Linus Walleij [Fri, 31 Aug 2018 14:13:07 +0000 (16:13 +0200)]
of/platform: initialise AMBA default DMA masks
This addresses a v4.19-rc1 regression in the PL111 DRM driver in
drivers/gpu/pl111/*
The driver uses the CMA KMS helpers and will thus at some point call
down to dma_alloc_attrs() to allocate a chunk of contigous DMA memory
for the framebuffer.
It appears that in v4.18, it was OK that this (and other DMA mastering
AMBA devices) left dev->coherent_dma_mask blank (zero).
In v4.19-rc1 the WARN_ON_ONCE(dev && !dev->coherent_dma_mask) in
dma_alloc_attrs() in include/linux/dma-mapping.h is triggered. The
allocation later fails when get_coherent_dma_mask() is called from
__dma_alloc() and __dma_alloc() returns NULL:
drm-clcd-pl111 dev:20: coherent DMA mask is unset
drm-clcd-pl111 dev:20: [drm:drm_fb_helper_fbdev_setup] *ERROR*
Failed to set fbdev configuration
It turns out that in commit 4d8bde883bfb ("OF: Don't set default
coherent DMA mask") the OF core stops setting the default DMA mask on
new devices, especially those lines of the patch:
- if (!dev->coherent_dma_mask)
- dev->coherent_dma_mask = DMA_BIT_MASK(32);
Robin Murphy solved a similar problem in a5516219b102 ("of/platform:
Initialise default DMA masks") by simply assigning dev.coherent_dma_mask
and the dev.dma_mask to point to the same when creating devices from the
device tree, and introducing the same code into the code path creating
AMBA/PrimeCell devices solved my problem, graphics now come up.
The code simply assumes that the device can access all of the system
memory by setting the coherent DMA mask to 0xffffffff when creating a
device from the device tree, which is crude, but seems to be what kernel
v4.18 assumed.
The AMBA PrimeCells do not differ between coherent and streaming DMA so
we can just assign the same to any DMA mask.
Possibly drivers should augment their coherent DMA mask in accordance
with "dma-ranges" from the device tree if more finegranular masking is
needed.
sparc: set a default 32-bit dma mask for OF devices
This keeps the historic default behavior for devices without a DMA mask,
but removes the warning about a lacking DMA mask for doing DMA without
a mask.
net: bgmac: remove set but not used variable 'err'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bgmac.c: In function 'bgmac_dma_alloc':
drivers/net/ethernet/broadcom/bgmac.c:619:6: warning:
variable 'err' set but not used [-Wunused-but-set-variable]
Florian Fainelli [Fri, 31 Aug 2018 19:29:49 +0000 (12:29 -0700)]
net: dsa: b53: Provide sensible defaults
The SRAB driver is the default way to communicate with the integrated
switch on iProc platforms and the MMAP driver is the way to communicate
with the integrated switch on DSL BCM63xx and CM BCM33xx.
YueHaibing [Fri, 31 Aug 2018 12:03:56 +0000 (12:03 +0000)]
liquidio: remove set but not used variable 'irh'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/request_manager.c: In function 'lio_process_iq_request_list':
drivers/net/ethernet/cavium/liquidio/request_manager.c:383:27: warning:
variable 'irh' set but not used [-Wunused-but-set-variable]
Driver displays an error message for each unrecognized dcbx TLV that's
received from the peer or configured on the device. It is observed that
syslog will be flooded with such messages in certain scenarios e.g.,
frequent link-flaps/lldp-transactions. Changing the severity of this
message to verbose level as it's not an error scenario/message.
Arnd Bergmann [Wed, 29 Aug 2018 15:47:19 +0000 (17:47 +0200)]
rds: store socket timestamps as ktime_t
rds is the last in-kernel user of the old do_gettimeofday()
function. Convert it over to ktime_get_real() to make it
work more like the generic socket timestamps, and to let
us kill off do_gettimeofday().
A follow-up patch will have to change the user space interface
to deal better with 32-bit tasks, which may use an incompatible
layout for 'struct timespec'.
Vakul Garg [Wed, 29 Aug 2018 09:56:55 +0000 (15:26 +0530)]
net/tls: Add support for async decryption of tls records
When tls records are decrypted using asynchronous acclerators such as
NXP CAAM engine, the crypto apis return -EINPROGRESS. Presently, on
getting -EINPROGRESS, the tls record processing stops till the time the
crypto accelerator finishes off and returns the result. This incurs a
context switch and is not an efficient way of accessing the crypto
accelerators. Crypto accelerators work efficient when they are queued
with multiple crypto jobs without having to wait for the previous ones
to complete.
The patch submits multiple crypto requests without having to wait for
for previous ones to complete. This has been implemented for records
which are decrypted in zero-copy mode. At the end of recvmsg(), we wait
for all the asynchronous decryption requests to complete.
The references to records which have been sent for async decryption are
dropped. For cases where record decryption is not possible in zero-copy
mode, asynchronous decryption is not used and we wait for decryption
crypto api to complete.
For crypto requests executing in async fashion, the memory for
aead_request, sglists and skb etc is freed from the decryption
completion handler. The decryption completion handler wakesup the
sleeping user context when recvmsg() flags that it has done sending
all the decryption requests and there are no more decryption requests
pending to be completed.
Olof Johansson [Sun, 2 Sep 2018 01:22:19 +0000 (18:22 -0700)]
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
projects / linux.git / log