Merge tag 'iio-fixes-for-5.9a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.9 cycle
Most of the fixes this time are for a long term issue that Lars-Peter
Clausen identified recently.
IIO assumes that any data pushed to the buffer interface (either kfifo
or another in kernel consumer) are naturally aligned. Unfortunately
this isn't true in a number of drivers, mostly by failing to ensure
the buffer used is aligned suitably for an s64 timestamp.
For the ones covered this time we use a structure to enforce this
alignment, with the added need for __aligned(8) to ensure 8 byte
alignment of the timestamp on x86_32 and similar platforms where
it would be 4 byte aligned giving different padded from some other
architectures.
Patches to make this requirement clearer and potentially cause an
error print will follow once we've cleaned up existing cases.
Note that it is a very hard to hit problem and as a result of this
as we only have one bug report despite the problem being present
for many years.
Other fixes:
* cros_ec:
- set gyroscope default frequency. For some older boards not having
this set can lead to a choice that doesn't work.
* counter,microchip-tcb-capture:
- Fix a wrong value check in error check.
* mcp3422
- Fix locking to protect against race condition.
* meson-adc
- Use right device when looking up fuse values for calibration.
* rockchip-adc
- Fix missing Kconfig dependency.
* ti-ads1015:
- Fix reading when CONFIG_PM not set.
* tag 'iio-fixes-for-5.9a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: mcp3422: fix locking scope
iio: adc: meson-saradc: Use the parent device to look up the calib data
iio:adc:max1118 Fix alignment of timestamp and data leak issues
iio:adc:ina2xx Fix timestamp alignment issue.
iio:adc:ti-adc084s021 Fix alignment and data leak issues.
iio:adc:ti-adc081c Fix alignment and data leak issues
iio:magnetometer:ak8975 Fix alignment and data leak issues.
iio:light:ltr501 Fix timestamp alignment issue.
iio:light:max44000 Fix timestamp alignment and prevent data leak.
iio:chemical:ccs811: Fix timestamp alignment and prevent data leak.
iio:proximity:mb1232: Fix timestamp alignment and prevent data leak.
iio:accel:mma7455: Fix timestamp alignment and prevent data leak.
iio:accel:bmc150-accel: Fix timestamp alignment and prevent data leak.
iio:accel:mma8452: Fix timestamp alignment and prevent data leak.
iio: accel: kxsd9: Fix alignment of local buffer.
iio: adc: rockchip_saradc: select IIO_TRIGGERED_BUFFER
iio: adc: ti-ads1015: fix conversion when CONFIG_PM is not set
counter: microchip-tcb-capture: check the correct variable
iio: cros_ec: Set Gyroscope default frequency to 25Hz
Max Staudt [Thu, 27 Aug 2020 15:49:00 +0000 (17:49 +0200)]
affs: fix basic permission bits to actually work
The basic permission bits (protection bits in AmigaOS) have been broken
in Linux' AFFS - it would only set bits, but never delete them.
Also, contrary to the documentation, the Archived bit was not handled.
Let's fix this for good, and set the bits such that Linux and classic
AmigaOS can coexist in the most peaceful manner.
Also, update the documentation to represent the current state of things.
Locking should be held for the entire reading sequence involving setting
the channel, waiting for the channel switch and reading from the
channel.
If not, reading from a channel can result mixing with the reading from
another channel.
iio: adc: meson-saradc: Use the parent device to look up the calib data
On the older-gen 32-bit SoCs the meson-saradc driver is used to read the
SoC temperature. This requires reading calibration data from the eFuse.
Looking up the calibration data nvmem-cell requires the OF device_node
pointer to be available in the struct device which is passed to
devm_nvmem_cell_get(). This however got lost with commit 8cb631ccbb1952
("iio: Remove superfluous of_node assignments") from indio_dev->dev. As
devm_nvmem_cell_get() is called in the initialization phase the
device_node is not yet available because the NVMEM cell is looked up
before iio_device_register() is called (which would then set the
device_node automatically).
Use the parent device to look up the NVMEM cell instead to fix this
issue.
Fixes: 8cb631ccbb1952 ("iio: Remove superfluous of_node assignments") Signed-off-by: Martin Blumenstingl <[email protected]> Signed-off-by: Jonathan Cameron <[email protected]>
Jonathan Cameron [Wed, 22 Jul 2020 15:51:03 +0000 (16:51 +0100)]
iio:adc:max1118 Fix alignment of timestamp and data leak issues
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The explicit alignment of ts is necessary to ensure correct padding
on architectures where s64 is only 4 bytes aligned such as x86_32.
Jonathan Cameron [Wed, 22 Jul 2020 15:51:02 +0000 (16:51 +0100)]
iio:adc:ina2xx Fix timestamp alignment issue.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses a 32 byte array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data with alignment
explicitly requested. This data is allocated with kzalloc so no
data can leak apart from previous readings. The explicit alignment
isn't technically needed here, but it reduced fragility and avoids
cut and paste into drivers where it will be needed.
If we want this in older stables will need manual backport due to
driver reworks.
Jonathan Cameron [Wed, 22 Jul 2020 15:50:57 +0000 (16:50 +0100)]
iio:adc:ti-adc084s021 Fix alignment and data leak issues.
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart from
previous readings.
The force alignment of ts is not strictly necessary in this case
but reduces the fragility of the code.
Jonathan Cameron [Wed, 22 Jul 2020 15:50:56 +0000 (16:50 +0100)]
iio:adc:ti-adc081c Fix alignment and data leak issues
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv().
This data is allocated with kzalloc so no data can leak apart
from previous readings.
The eplicit alignment of ts is necessary to ensure correct padding
on x86_32 where s64 is only aligned to 4 bytes.
Viresh Kumar [Mon, 31 Aug 2020 07:33:06 +0000 (13:03 +0530)]
opp: Don't drop reference for an OPP table that was never parsed
dev_pm_opp_remove_table() should drop a reference to the OPP table only
if the DT OPP table was parsed earlier with a call to
dev_pm_opp_of_add_table() earlier. Else it may end up dropping the
reference to the OPP table, which was added as a result of other calls
like dev_pm_opp_set_clkname(). And would hence result in undesirable
behavior later on when caller would try to free the resource again.
Roger Quadros [Mon, 24 Aug 2020 07:51:26 +0000 (10:51 +0300)]
phy: omap-usb2-phy: disable PHY charger detect
AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs. Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.
This addresses Silicon Errata:
i2075 - "USB2PHY: USB2PHY Charger Detect is Enabled by Default Without VBUS
Presence"
HID: quirks: Set INCREMENT_USAGE_ON_DUPLICATE for all Saitek X52 devices
The Saitek X52 family of joysticks has a pair of axes that were
originally (by the Windows driver) used as mouse pointer controls. The
corresponding usage page is the Game Controls page, which is not
recognized by the generic HID driver, and therefore, both axes get
mapped to ABS_MISC. The quirk makes the second axis get mapped to
ABS_MISC+1, and therefore made available separately.
One Saitek X52 device is already fixed. This patch fixes the other two
known devices with VID/PID 06a3:0255 and 06a3:0762.
Bjørn Mork [Sat, 29 Aug 2020 13:42:50 +0000 (15:42 +0200)]
USB: serial: option: support dynamic Quectel USB compositions
The USB composition, defining the set of exported functions, is dynamic
in newer Quectel modems. Default functions can be disabled and
alternative functions can be enabled instead. The alternatives
includes class functions using interface pairs, which should be
handled by the respective class drivers.
Active interfaces are numbered consecutively, so static
blacklisting based on interface numbers will fail when the
composition changes. An example of such an error, where the
option driver has bound to the CDC ECM data interface,
preventing cdc_ether from handling this function:
Change rules for EC21, EC25, BG96 and EG95 to match vendor specific
serial functions only, to prevent binding to class functions. Require
2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET
network functions.
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: AT-capable port (data).
In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module
exposes 6 TTY ports:
The purpose of each TTY is as follows:
* ttyUSB0: DIAG/QCDM port.
* ttyUSB1: GNSS data.
* ttyUSB2: AT-capable port (control).
* ttyUSB3: QFLOG interface.
* ttyUSB4: DAM interface.
* ttyUSB5: AT-capable port (data).
Tuong Lien [Sat, 29 Aug 2020 19:37:55 +0000 (02:37 +0700)]
tipc: fix using smp_processor_id() in preemptible
The 'this_cpu_ptr()' is used to obtain the AEAD key' TFM on the current
CPU for encryption, however the execution can be preemptible since it's
actually user-space context, so the 'using smp_processor_id() in
preemptible' has been observed.
We fix the issue by using the 'get/put_cpu_ptr()' API which consists of
a 'preempt_disable()' instead.
Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication") Acked-by: Jon Maloy <[email protected]> Signed-off-by: Tuong Lien <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Sun, 30 Aug 2020 22:53:44 +0000 (15:53 -0700)]
Merge branch 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- fix regression in af_alg that affects iwd
- restore polling delay in qat
- fix double free in ingenic on error path
- fix potential build failure in sa2ul due to missing Kconfig dependency
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: af_alg - Work around empty control messages without MSG_MORE
crypto: sa2ul - add Kconfig selects to fix build error
crypto: ingenic - Drop kfree for memory allocated with devm_kzalloc
crypto: qat - add delay before polling mailbox
Paul Cercueil [Thu, 27 Aug 2020 11:44:04 +0000 (13:44 +0200)]
drm/ingenic: Fix driver not probing when IPU port is missing
Even if support for the IPU was compiled in, we may run on a device
(e.g. the Qi LB60) where the IPU is not available, or simply with an old
devicetree without the IPU node. In that case the ingenic-drm refused to
probe.
Fix the driver so that it will probe even if the IPU node is not present
in devicetree (but then IPU support is disabled of course).
Linus Torvalds [Sun, 30 Aug 2020 19:01:23 +0000 (12:01 -0700)]
Merge tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Three interrupt related fixes for X86:
- Move disabling of the local APIC after invoking fixup_irqs() to
ensure that interrupts which are incoming are noted in the IRR and
not ignored.
- Unbreak affinity setting.
The rework of the entry code reused the regular exception entry
code for device interrupts. The vector number is pushed into the
errorcode slot on the stack which is then lifted into an argument
and set to -1 because that's regs->orig_ax which is used in quite
some places to check whether the entry came from a syscall.
But it was overlooked that orig_ax is used in the affinity cleanup
code to validate whether the interrupt has arrived on the new
target. It turned out that this vector check is pointless because
interrupts are never moved from one vector to another on the same
CPU. That check is a historical leftover from the time where x86
supported multi-CPU affinities, but not longer needed with the now
strict single CPU affinity. Famous last words ...
- Add a missing check for an empty cpumask into the matrix allocator.
The affinity change added a warning to catch the case where an
interrupt is moved on the same CPU to a different vector. This
triggers because a condition with an empty cpumask returns an
assignment from the allocator as the allocator uses for_each_cpu()
without checking the cpumask for being empty. The historical
inconsistent for_each_cpu() behaviour of ignoring the cpumask and
unconditionally claiming that CPU0 is in the mask struck again.
Sigh.
plus a new entry into the MAINTAINER file for the HPE/UV platform"
* tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Deal with the sillyness of for_each_cpu() on UP
x86/irq: Unbreak interrupt affinity setting
x86/hotplug: Silence APIC only after all interrupts are migrated
MAINTAINERS: Add entry for HPE Superdome Flex (UV) maintainers
Linus Torvalds [Sun, 30 Aug 2020 18:56:54 +0000 (11:56 -0700)]
Merge tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for interrupt chip drivers:
- Revert the platform driver conversion of interrupt chip drivers as
it turned out to create more problems than it solves.
- Fix a trivial typo in the new module helpers which made probing
reliably fail.
- Small fixes in the STM32 and MIPS Ingenic drivers
- The TI firmware rework which had badly managed dependencies and had
to wait post rc1"
* tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/ingenic: Leave parent IRQ unmasked on suspend
irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers
arm64: dts: k3-am65: Update the RM resource types
arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field
dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml
dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent.
irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml
dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent
firmware: ti_sci: Add support for getting resource with subtype
firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
firmware: ti_sci: Drop the device id to resource type translation
Linus Torvalds [Sun, 30 Aug 2020 18:50:53 +0000 (11:50 -0700)]
Merge tag 'sched-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"A single fix for the scheduler:
- Make is_idle_task() __always_inline to prevent the compiler from
putting it out of line into the wrong section because it's used
inside noinstr sections"
* tag 'sched-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Use __always_inline on is_idle_task()
Linus Torvalds [Sun, 30 Aug 2020 17:56:12 +0000 (10:56 -0700)]
Merge tag 'powerpc-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Revert our removal of PROT_SAO, at least one user expressed an
interest in using it on Power9. Instead don't allow it to be used in
guests unless enabled explicitly at compile time.
- A fix for a crash introduced by a recent change to FP handling.
- Revert a change to our idle code that left Power10 with no idle
support.
- One minor fix for the new scv system call path to set PPR.
- Fix a crash in our "generic" PMU if branch stack events were enabled.
- A fix for the IMC PMU, to correctly identify host kernel samples.
- The ADB_PMU powermac code was found to be incompatible with
VMAP_STACK, so make them incompatible in Kconfig until the code can
be fixed.
- A build fix in drivers/video/fbdev/controlfb.c, and a documentation
fix.
Thanks to Alexey Kardashevskiy, Athira Rajeev, Christophe Leroy,
Giuseppe Sacco, Madhavan Srinivasan, Milton Miller, Nicholas Piggin,
Pratik Rajesh Sampat, Randy Dunlap, Shawn Anastasio, Vaidyanathan
Srinivasan.
* tag 'powerpc-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32s: Disable VMAP stack which CONFIG_ADB_PMU
Revert "powerpc/powernv/idle: Replace CPU feature check with PVR check"
powerpc/perf: Fix reading of MSR[HV/PR] bits in trace-imc
powerpc/perf: Fix crashes with generic_compat_pmu & BHRB
powerpc/64s: Fix crash in load_fp_state() due to fpexc_mode
powerpc/64s: scv entry should set PPR
Documentation/powerpc: fix malformed table in syscall64-abi
video: fbdev: controlfb: Fix build for COMPILE_TEST=y && PPC_PMAC=n
selftests/powerpc: Update PROT_SAO test to skip ISA 3.1
powerpc/64s: Disallow PROT_SAO in LPARs by default
Revert "powerpc/64s: Remove PROT_SAO support"
Linus Torvalds [Sun, 30 Aug 2020 17:51:03 +0000 (10:51 -0700)]
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
Linus Torvalds [Sun, 30 Aug 2020 17:47:23 +0000 (10:47 -0700)]
Merge tag 'edac_urgent_for_v5.9_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
"A fix to properly clear ghes_edac driver state on driver remove so
that a subsequent load can probe the system properly (Shiju Jose)"
* tag 'edac_urgent_for_v5.9_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/ghes: Fix NULL pointer dereference in ghes_edac_register()
Thomas Gleixner [Sun, 30 Aug 2020 17:07:53 +0000 (19:07 +0200)]
genirq/matrix: Deal with the sillyness of for_each_cpu() on UP
Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.
The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027fffff799 ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.
Add a check for the cpumask being empty to prevent this.
Linus Torvalds [Sat, 29 Aug 2020 20:50:56 +0000 (13:50 -0700)]
fsldma: fix very broken 32-bit ppc ioread64 functionality
Commit ef91bb196b0d ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.
That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical. There were no
high bits to mask off to begin with.
But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.
Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all. Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.
This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.
This patch at least makes it not fail the build any more, and makes the
logic superficially sane. Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Linus Torvalds [Sat, 29 Aug 2020 19:51:58 +0000 (12:51 -0700)]
Merge tag 's390-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Disable preemption trace in percpu macros since the lockdep code
itself uses percpu variables now and it causes recursions.
- Fix kernel space 4-level paging broken by recent vmem rework.
* tag 's390-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vmem: fix vmem_add_range for 4-level paging
s390: don't trace preemption in percpu macros
Linus Torvalds [Sat, 29 Aug 2020 19:44:30 +0000 (12:44 -0700)]
Merge tag 'for-linus-5.9-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two fixes for Xen: one needed for ongoing work to support virtio with
Xen, and one for a corner case in IRQ handling with Xen"
* tag 'for-linus-5.9-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
arm/xen: Add misuse warning to virt_to_gfn
xen/xenbus: Fix granting of vmalloc'd memory
XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.
Linus Torvalds [Sat, 29 Aug 2020 19:37:00 +0000 (12:37 -0700)]
Merge tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix tempeerature scale in gsc-hwmon driver
- Fix divide by 0 error in nct7904 driver
- Drop non-existing attribute from pmbus/isl68137 driver
- Fix status check in applesmc driver
* tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gsc-hwmon) Scale temperature to millidegrees
hwmon: (applesmc) check status earlier.
hwmon: (nct7904) Correct divide by 0
hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228
Jens Axboe [Sat, 29 Aug 2020 16:54:11 +0000 (10:54 -0600)]
Merge branch 'nvme-5.9-rc' of git://git.infradead.org/nvme into block-5.9
Pull NVMe fixes from Sagi:
"- instance leak and io boundary fixes from Keith
- fc locking fix from Christophe
- various tcp/rdma reset during traffic fixes from Me
- pci use-after-free fix from Tong
- tcp target null deref fix from Ziye"
* 'nvme-5.9-rc' of git://git.infradead.org/nvme:
nvme-pci: cancel nvme device request before disabling
nvme: only use power of two io boundaries
nvme: fix controller instance leak
nvmet-fc: Fix a missed _irqsave version of spin_lock in 'nvmet_fc_fod_op_done()'
nvme: Fix NULL dereference for pci nvme controllers
nvme-rdma: fix reset hang if controller died in the middle of a reset
nvme-rdma: fix timeout handler
nvme-rdma: serialize controller teardown sequences
nvme-tcp: fix reset hang if controller died in the middle of a reset
nvme-tcp: fix timeout handler
nvme-tcp: serialize controller teardown sequences
nvme: have nvme_wait_freeze_timeout return if it timed out
nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptance
nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pdu
Florian Westphal [Tue, 25 Aug 2020 22:07:18 +0000 (00:07 +0200)]
netfilter: conntrack: do not auto-delete clash entries on reply
Its possible that we have more than one packet with the same ct tuple
simultaneously, e.g. when an application emits n packets on same UDP
socket from multiple threads.
NAT rules might be applied to those packets. With the right set of rules,
n packets will be mapped to m destinations, where at least two packets end
up with the same destination.
When this happens, the existing clash resolution may merge the skb that
is processed after the first has been received with the identical tuple
already in hash table.
However, its possible that this identical tuple is a NAT_CLASH tuple.
In that case the second skb will be sent, but no reply can be received
since the reply that is processed first removes the NAT_CLASH tuple.
Do not auto-delete, this gives a 1 second window for replies to be passed
back to originator.
Packets that are coming later (udp stream case) will not be affected:
they match the original ct entry, not a NAT_CLASH one.
Also prevent NAT_CLASH entries from getting offloaded.
Fixes: 6a757c07e51f ("netfilter: conntrack: allow insertion of clashing entries") Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
sparse: use static inline for __chk_{user,io}_ptr()
__chk_user_ptr() & __chk_io_ptr() are dummy extern functions which
only exist to enforce the typechecking of __user or __iomem pointers
in macros when using sparse.
This typechecking is done by inserting a call to these functions.
But the presence of these calls can inhibit some simplifications
and so influence the result of sparse's analysis of context/locking.
Fix this by changing these calls into static inline calls with
an empty body.
Dan Crawford [Sat, 29 Aug 2020 02:49:46 +0000 (12:49 +1000)]
ALSA: hda - Fix silent audio output and corrupted input on MSI X570-A PRO
Following Christian Lachner's patch for Gigabyte X570-based motherboards,
also patch the MSI X570-A PRO motherboard; the ALC1220 codec requires the
same workaround for Clevo laptops to enforce the DAC/mixer connection
path. Set up a quirk entry for that.
I suspect most if all X570 motherboards will require similar patches.
[ The entries reordered in the SSID order -- tiwai ]
Tong Zhang [Fri, 28 Aug 2020 14:17:08 +0000 (10:17 -0400)]
nvme-pci: cancel nvme device request before disabling
This patch addresses an irq free warning and null pointer dereference
error problem when nvme devices got timeout error during initialization.
This problem happens when nvme_timeout() function is called while
nvme_reset_work() is still in execution. This patch fixed the problem by
setting flag of the problematic request to NVME_REQ_CANCELLED before
calling nvme_dev_disable() to make sure __nvme_submit_sync_cmd() returns
an error code and let nvme_submit_sync_cmd() fail gracefully.
The following is console output.
Keith Busch [Thu, 27 Aug 2020 17:38:57 +0000 (10:38 -0700)]
nvme: only use power of two io boundaries
The kernel requires a power of two for boundaries because that's the
only way it can efficiently split commands that cross them. A
controller, however, may report a non-power of two boundary.
The driver had been rounding the controller's value to one the kernel
can use, but splitting on the wrong boundary provides no benefit on the
device side, and incurs additional submission overhead from non-optimal
splits.
Don't provide any boundary hint if the controller's value can't be used
and log a warning when first scanning a disk's unreported IO boundary.
Since the chunk sector logic has grown, move it to a separate function.
Keith Busch [Wed, 26 Aug 2020 17:53:04 +0000 (10:53 -0700)]
nvme: fix controller instance leak
If the driver has to unbind from the controller for an early failure
before the subsystem has been set up, there won't be a subsystem holding
the controller's instance, so the controller needs to free its own
instance in this case.
nvme-rdma: fix reset hang if controller died in the middle of a reset
If the controller becomes unresponsive in the middle of a reset, we
will hang because we are waiting for the freeze to complete, but that
cannot happen since we have commands that are inflight holding the
q_usage_counter, and we can't blindly fail requests that times out.
So give a timeout and if we cannot wait for queue freeze before
unfreezing, fail and have the error handling take care how to
proceed (either schedule a reconnect of remove the controller).
When a request times out in a LIVE state, we simply trigger error
recovery and let the error recovery handle the request cancellation,
however when a request times out in a non LIVE state, we make sure to
complete it immediately as it might block controller setup or teardown
and prevent forward progress.
However tearing down the entire set of I/O and admin queues causes
freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really
an overkill to what we actually need, which is to just fence controller
teardown that may be running, stop the queue, and cancel the request if
it is not already completed.
Now that we have the controller teardown_lock, we can safely serialize
request cancellation. This addresses a hang caused by calling extra
queue freeze on controller namespaces, causing unfreeze to not complete
correctly.
In the timeout handler we may need to complete a request because the
request that timed out may be an I/O that is a part of a serial sequence
of controller teardown or initialization. In order to complete the
request, we need to fence any other context that may compete with us
and complete the request that is timing out.
In this case, we could have a potential double completion in case
a hard-irq or a different competing context triggered error recovery
and is running inflight request cancellation concurrently with the
timeout handler.
Protect using a ctrl teardown_lock to serialize contexts that may
complete a cancelled request due to error recovery or a reset.
nvme-tcp: fix reset hang if controller died in the middle of a reset
If the controller becomes unresponsive in the middle of a reset, we will
hang because we are waiting for the freeze to complete, but that cannot
happen since we have commands that are inflight holding the
q_usage_counter, and we can't blindly fail requests that times out.
So give a timeout and if we cannot wait for queue freeze before
unfreezing, fail and have the error handling take care how to proceed
(either schedule a reconnect of remove the controller).
When a request times out in a LIVE state, we simply trigger error
recovery and let the error recovery handle the request cancellation,
however when a request times out in a non LIVE state, we make sure to
complete it immediately as it might block controller setup or teardown
and prevent forward progress.
However tearing down the entire set of I/O and admin queues causes
freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really
an overkill to what we actually need, which is to just fence controller
teardown that may be running, stop the queue, and cancel the request if
it is not already completed.
Now that we have the controller teardown_lock, we can safely serialize
request cancellation. This addresses a hang caused by calling extra
queue freeze on controller namespaces, causing unfreeze to not complete
correctly.
Sagi Grimberg [Thu, 6 Aug 2020 01:13:48 +0000 (18:13 -0700)]
nvme-tcp: serialize controller teardown sequences
In the timeout handler we may need to complete a request because the
request that timed out may be an I/O that is a part of a serial sequence
of controller teardown or initialization. In order to complete the
request, we need to fence any other context that may compete with us
and complete the request that is timing out.
In this case, we could have a potential double completion in case
a hard-irq or a different competing context triggered error recovery
and is running inflight request cancellation concurrently with the
timeout handler.
Protect using a ctrl teardown_lock to serialize contexts that may
complete a cancelled request due to error recovery or a reset.
nvme: have nvme_wait_freeze_timeout return if it timed out
Users can detect if the wait has completed or not and take appropriate
actions based on this information (e.g. weather to continue
initialization or rather fail and schedule another initialization
attempt).
Sagi Grimberg [Fri, 14 Aug 2020 18:46:51 +0000 (11:46 -0700)]
nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptance
NVME_CTRL_NEW should never see any I/O, because in order to start
initialization it has to transition to NVME_CTRL_CONNECTING and from
there it will never return to this state.
Ziye Yang [Fri, 21 Aug 2020 16:48:10 +0000 (00:48 +0800)]
nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pdu
When handling commands without in-capsule data, we assign the ttag
assuming we already have the queue commands array allocated (based
on the queue size information in the connect data payload). However
if the connect itself did not send the connect data in-capsule we
have yet to allocate the queue commands,and we will assign a bogus
ttag and suffer a NULL dereference when we receive the corresponding
h2cdata pdu.
Fix this by checking if we already allocated commands before
dereferencing it when handling h2cdata, if we didn't, its for sure a
connect and we should use the preallocated connect command.
Linus Torvalds [Fri, 28 Aug 2020 23:38:29 +0000 (16:38 -0700)]
Merge tag 'block-5.9-2020-08-28' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- nbd timeout fix (Hou)
- device size fix for loop LOOP_CONFIGURE (Martijn)
- MD pull from Song with raid5 stripe size fix (Yufen)
* tag 'block-5.9-2020-08-28' of git://git.kernel.dk/linux-block:
md/raid5: make sure stripe_size as power of two
loop: Set correct device size when using LOOP_CONFIGURE
nbd: restore default timeout when setting it to zero
Linus Torvalds [Fri, 28 Aug 2020 23:23:16 +0000 (16:23 -0700)]
Merge tag 'io_uring-5.9-2020-08-28' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few fixes in here, all based on reports and test cases from folks
using it. Most of it is stable material as well:
- Hashed work cancelation fix (Pavel)
- poll wakeup signalfd fix
- memlock accounting fix
- nonblocking poll retry fix
- ensure we never return -ERESTARTSYS for reads
- ensure offset == -1 is consistent with preadv2() as documented
- IOPOLL -EAGAIN handling fixes
- remove useless task_work bounce for block based -EAGAIN retry"
* tag 'io_uring-5.9-2020-08-28' of git://git.kernel.dk/linux-block:
io_uring: don't bounce block based -EAGAIN retry off task_work
io_uring: fix IOPOLL -EAGAIN retries
io_uring: clear req->result on IOPOLL re-issue
io_uring: make offset == -1 consistent with preadv2/pwritev2
io_uring: ensure read requests go through -ERESTART* transformation
io_uring: don't use poll handler if file can't be nonblocking read/written
io_uring: fix imbalanced sqo_mm accounting
io_uring: revert consumed iov_iter bytes on error
io-wq: fix hang after cancelling pending hashed work
io_uring: don't recurse on tsk->sighand->siglock with signalfd
Linus Torvalds [Fri, 28 Aug 2020 20:23:31 +0000 (13:23 -0700)]
Merge tag 'devprop-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework fix from Rafael Wysocki:
"Prevent the promotion of the secondary firmware node of a device to
the primary one from leaking a pointer (Heikki Krogerus)"
* tag 'devprop-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Fix the secondary firmware node handling in set_primary_fwnode()
Linus Torvalds [Fri, 28 Aug 2020 20:17:14 +0000 (13:17 -0700)]
Merge tag 'acpi-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two recent issues in the ACPI memory mappings management
code and tighten up error handling in the ACPI driver for AMD SoCs
(APD).
Specifics:
- Avoid redundant rounding to the page size in acpi_os_map_iomem() to
address a recently introduced issue with the EFI memory map
permission check on ARM64 (Ard Biesheuvel).
- Fix acpi_release_memory() to wait until the memory mappings
released by it have been really unmapped (Rafael Wysocki).
- Make the ACPI driver for AMD SoCs (APD) check the return value of
acpi_dev_get_property() to avoid failures in the cases when the
device property under inspection is missing (Furquan Shaikh)"
* tag 'acpi-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: OSL: Prevent acpi_release_memory() from returning too early
ACPI: ioremap: avoid redundant rounding to OS page size
ACPI: SoC: APD: Check return value of acpi_dev_get_property()
Linus Torvalds [Fri, 28 Aug 2020 20:12:09 +0000 (13:12 -0700)]
Merge tag 'pm-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix the recently added Tegra194 cpufreq driver and the handling
of devices using runtime PM during system-wide suspend, improve the
intel_pstate driver documentation and clean up the cpufreq core.
Specifics:
- Make the recently added Tegra194 cpufreq driver use
read_cpuid_mpir() instead of cpu_logical_map() to avoid exporting
logical_cpu_map (Sumit Gupta).
- Drop the automatic system wakeup event reporting for devices with
pending runtime-resume requests during system-wide suspend to avoid
spurious aborts of the suspend flow (Rafael Wysocki).
- Fix build warning in the intel_pstate driver documentation and
improve the wording in there (Randy Dunlap).
- Clean up two pieces of code in the cpufreq core (Viresh Kumar)"
* tag 'pm-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Use WARN_ON_ONCE() for invalid relation
cpufreq: No need to verify cpufreq_driver in show_scaling_cur_freq()
PM: sleep: core: Fix the handling of pending runtime resume requests
Documentation: fix pm/intel_pstate build warning and wording
cpufreq: replace cpu_logical_map() with read_cpuid_mpir()
* pm-cpufreq:
cpufreq: Use WARN_ON_ONCE() for invalid relation
cpufreq: No need to verify cpufreq_driver in show_scaling_cur_freq()
Documentation: fix pm/intel_pstate build warning and wording
cpufreq: replace cpu_logical_map() with read_cpuid_mpir()
Linus Torvalds [Fri, 28 Aug 2020 18:37:33 +0000 (11:37 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix kernel build with the integrated LLVM assembler which doesn't see
the -Wa,-march option.
- Fix "make vdso_install" when COMPAT_VDSO is disabled.
- Make KVM more robust if the AT S1E1R instruction triggers an
exception (architecture corner cases).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
KVM: arm64: Set HCR_EL2.PTW to prevent AT taking synchronous exception
KVM: arm64: Survive synchronous exceptions caused by AT instructions
KVM: arm64: Add kvm_extable for vaxorcism code
arm64: vdso32: make vdso32 install conditional
arm64: use a common .arch preamble for inline assembly
Herbert Xu [Fri, 28 Aug 2020 07:11:25 +0000 (17:11 +1000)]
kernel.h: Silence sparse warning in lower_32_bits
I keep getting sparse warnings in crypto such as:
CHECK drivers/crypto/ccree/cc_hash.c
drivers/crypto/ccree/cc_hash.c:49:9: warning: cast truncates bits from constant value (47b5481dbefa4fa4 becomes befa4fa4)
drivers/crypto/ccree/cc_hash.c:49:26: warning: cast truncates bits from constant value (db0c2e0d64f98fa7 becomes 64f98fa7)
[.. many more ..]
This patch removes the warning by adding a mask to keep sparse
happy.
Fabian Frederick [Sun, 23 Aug 2020 18:15:59 +0000 (20:15 +0200)]
selftests: netfilter: exit on invalid parameters
exit script with comments when parameters are wrong during address
addition. No need for a message when trying to change MTU with lower
values: output is self-explanatory.
Use short testing sequence to avoid shellcheck warnings
(suggested by Stefano Brivio).
netfilter: nfnetlink: nfnetlink_unicast() reports EAGAIN instead of ENOBUFS
Frontend callback reports EAGAIN to nfnetlink to retry a command, this
is used to signal that module autoloading is required. Unfortunately,
nlmsg_unicast() reports EAGAIN in case the receiver socket buffer gets
full, so it enters a busy-loop.
This patch updates nfnetlink_unicast() to turn EAGAIN into ENOBUFS and
to use nlmsg_unicast(). Remove the flags field in nfnetlink_unicast()
since this is always MSG_DONTWAIT in the existing code which is exactly
what nlmsg_unicast() passes to netlink_unicast() as parameter.
Fixes: 96518518cc41 ("netfilter: add nftables") Reported-by: Phil Sutter <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
Linus Torvalds [Fri, 28 Aug 2020 17:57:14 +0000 (10:57 -0700)]
Merge tag 'writeback_for_v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull writeback fixes from Jan Kara:
"Fixes for writeback code occasionally skipping writeback of some
inodes or livelocking sync(2)"
* tag 'writeback_for_v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
writeback: Drop I_DIRTY_TIME_EXPIRE
writeback: Fix sync livelock due to b_dirty_time processing
writeback: Avoid skipping inode writeback
writeback: Protect inode->i_io_list with inode->i_lock
Linus Torvalds [Fri, 28 Aug 2020 17:41:00 +0000 (10:41 -0700)]
Merge tag 'gfs2-v5.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 fix from Andreas Gruenbacher:
"Fix a memory leak on filesystem withdraw.
We didn't detect this bug because we have slab merging on by default
(CONFIG_SLAB_MERGE_DEFAULT). Adding 'slub_nomerge' to the kernel
command line exposed the problem"
* tag 'gfs2-v5.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: add some much needed cleanup for log flushes that fail
Linus Torvalds [Fri, 28 Aug 2020 17:33:04 +0000 (10:33 -0700)]
Merge tag 'ceph-for-5.9-rc3' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"We have an inode number handling change, prompted by s390x which is a
64-bit architecture with a 32-bit ino_t, a patch to disallow leases to
avoid potential data integrity issues when CephFS is re-exported via
NFS or CIFS and a fix for the bulk of W=1 compilation warnings"
* tag 'ceph-for-5.9-rc3' of git://github.com/ceph/ceph-client:
ceph: don't allow setlease on cephfs
ceph: fix inode number handling on arches with 32-bit ino_t
libceph: add __maybe_unused to DEFINE_CEPH_FEATURE
Paulo Alcantara [Thu, 27 Aug 2020 14:20:19 +0000 (11:20 -0300)]
cifs: fix check of tcon dfs in smb1
For SMB1, the DFS flag should be checked against tcon->Flags rather
than tcon->share_flags. While at it, add an is_tcon_dfs() helper to
check for DFS capability in a more generic way.
Linus Torvalds [Fri, 28 Aug 2020 17:15:33 +0000 (10:15 -0700)]
Merge tag 'mfd-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- fix double free
- handle devicetree disabled devices gracefully
* tag 'mfd-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: mfd-core: Ensure disabled devices are ignored without error
mfd: core: Fix double-free in mfd_remove_devices_fn()
Linus Torvalds [Fri, 28 Aug 2020 16:46:48 +0000 (09:46 -0700)]
Merge tag 'drm-fixes-2020-08-28' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"As expected a bit of an rc3 uptick, amdgpu and msm are the main ones,
one msm patch was from the merge window, but had dependencies and we
dropped it until the other tree had landed. Otherwise it's a couple of
fixes for core, and etnaviv, and single i915, exynos, omap fixes.
I'm still tracking the Sandybridge gpu relocations issue, if we don't
see much movement I might just queue up the reverts. I'll talk to
Daniel next week once he's back from holidays.
core:
- Take modeset bkl for legacy drivers
dp_mst:
- Allow null crtc in dp_mst
i915:
- Fix command parser desc matching with masks
amdgpu:
- Misc display fixes
- Backlight fixes
- MPO fix for DCN1
- Fixes for Sienna Cichlid
- Fixes for Navy Flounder
- Vega SW CTF fixes
- SMU fix for Raven
- Fix a possible overflow in INFO ioctl
- Gfx10 clockgating fix
exynos:
- Just drop __iommu annotation to fix sparse warning
omap:
- locking state fix"
* tag 'drm-fixes-2020-08-28' of git://anongit.freedesktop.org/drm/drm: (41 commits)
drm/amd/display: Fix memleak in amdgpu_dm_mode_config_init
drm/amdgpu: disable runtime pm for navy_flounder
drm/amd/display: Retry AUX write when fail occurs
drm/amdgpu: Fix buffer overflow in INFO ioctl
drm/amd/powerplay: Fix hardmins not being sent to SMU for RV
drm/amdgpu: use MODE1 reset for navy_flounder by default
drm/amd/pm: correct the thermal alert temperature limit settings
drm/amdgpu: add asd fw check before loading asd
drm/amd/display: Keep current gain when ABM disable immediately
drm/amd/display: Fix passive dongle mistaken as active dongle in EDID emulation
drm/amd/display: Revert HDCP disable sequence change
drm/amd/display: Send DISPLAY_OFF after power down on boot
drm/amdgpu/gfx10: refine mgcg setting
drm/amd/pm: correct Vega20 swctf limit setting
drm/amd/pm: correct Vega12 swctf limit setting
drm/amd/pm: correct Vega10 swctf limit setting
drm/amd/pm: set VCN pg per instances
drm/amd/pm: enable run_btc callback for sienna_cichlid
drivers: gpu: amd: Initialize amdgpu_dm_backlight_caps object to 0 in amdgpu_dm_update_backlight_caps
drm/amd/display: Reject overlay plane configurations in multi-display scenarios
...
James Morse [Fri, 21 Aug 2020 14:07:07 +0000 (15:07 +0100)]
KVM: arm64: Set HCR_EL2.PTW to prevent AT taking synchronous exception
AT instructions do a translation table walk and return the result, or
the fault in PAR_EL1. KVM uses these to find the IPA when the value is
not provided by the CPU in HPFAR_EL1.
If a translation table walk causes an external abort it is taken as an
exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11
"Synchronous faults generated by address translation instructions")
While we previously made KVM resilient to exceptions taken due to AT
instructions, the device access causes mismatched attributes, and may
occur speculatively. Prevent this, by forbidding a walk through memory
described as device at stage2. Now such AT instructions will report a
stage2 fault.
Such a fault will cause KVM to restart the guest. If the AT instructions
always walk the page tables, but guest execution uses the translation cached
in the TLB, the guest can't make forward progress until the TLB entry is
evicted. This isn't a problem, as since commit 5dcd0fdbb492 ("KVM: arm64:
Defer guest entry when an asynchronous exception is pending"), KVM will
return to the host to process IRQs allowing the rest of the system to keep
running.
James Morse [Fri, 21 Aug 2020 14:07:06 +0000 (15:07 +0100)]
KVM: arm64: Survive synchronous exceptions caused by AT instructions
KVM doesn't expect any synchronous exceptions when executing, any such
exception leads to a panic(). AT instructions access the guest page
tables, and can cause a synchronous external abort to be taken.
The arm-arm is unclear on what should happen if the guest has configured
the hardware update of the access-flag, and a memory type in TCR_EL1 that
does not support atomic operations. B2.2.6 "Possible implementation
restrictions on using atomic instructions" from DDI0487F.a lists
synchronous external abort as a possible behaviour of atomic instructions
that target memory that isn't writeback cacheable, but the page table
walker may behave differently.
Make KVM robust to synchronous exceptions caused by AT instructions.
Add a get_user() style helper for AT instructions that returns -EFAULT
if an exception was generated.
While KVM's version of the exception table mixes synchronous and
asynchronous exceptions, only one of these can occur at each location.
Re-enter the guest when the AT instructions take an exception on the
assumption the guest will take the same exception. This isn't guaranteed
to make forward progress, as the AT instructions may always walk the page
tables, but guest execution may use the translation cached in the TLB.
This isn't a problem, as since commit 5dcd0fdbb492 ("KVM: arm64: Defer guest
entry when an asynchronous exception is pending"), KVM will return to the
host to process IRQs allowing the rest of the system to keep running.
James Morse [Fri, 21 Aug 2020 14:07:05 +0000 (15:07 +0100)]
KVM: arm64: Add kvm_extable for vaxorcism code
KVM has a one instruction window where it will allow an SError exception
to be consumed by the hypervisor without treating it as a hypervisor bug.
This is used to consume asynchronous external abort that were caused by
the guest.
As we are about to add another location that survives unexpected exceptions,
generalise this code to make it behave like the host's extable.
KVM's version has to be mapped to EL2 to be accessible on nVHE systems.
The SError vaxorcism code is a one instruction window, so has two entries
in the extable. Because the KVM code is copied for VHE and nVHE, we end up
with four entries, half of which correspond with code that isn't mapped.
zhudi [Wed, 26 Aug 2020 12:01:13 +0000 (20:01 +0800)]
netlink: fix a data race in netlink_rcv_wake()
The data races were reported by KCSAN:
BUG: KCSAN: data-race in netlink_recvmsg / skb_queue_tail
write (marked) to 0xffff8c0986e5a8c8 of 8 bytes by interrupt on cpu 3:
skb_queue_tail+0xcc/0x120
__netlink_sendskb+0x55/0x80
netlink_broadcast_filtered+0x465/0x7e0
nlmsg_notify+0x8f/0x120
rtnl_notify+0x8e/0xb0
__neigh_notify+0xf2/0x120
neigh_update+0x927/0xde0
arp_process+0x8a3/0xf50
arp_rcv+0x27c/0x3b0
__netif_receive_skb_core+0x181c/0x1840
__netif_receive_skb+0x38/0xf0
netif_receive_skb_internal+0x77/0x1c0
napi_gro_receive+0x1bd/0x1f0
e1000_clean_rx_irq+0x538/0xb20 [e1000]
e1000_clean+0x5e4/0x1340 [e1000]
net_rx_action+0x310/0x9d0
__do_softirq+0xe8/0x308
irq_exit+0x109/0x110
do_IRQ+0x7f/0xe0
ret_from_intr+0x0/0x1d
0xffffffffffffffff
read to 0xffff8c0986e5a8c8 of 8 bytes by task 1463 on cpu 0:
netlink_recvmsg+0x40b/0x820
sock_recvmsg+0xc9/0xd0
___sys_recvmsg+0x1a4/0x3b0
__sys_recvmsg+0x86/0x120
__x64_sys_recvmsg+0x52/0x70
do_syscall_64+0xb5/0x360
entry_SYSCALL_64_after_hwframe+0x65/0xca
0xffffffffffffffff
Since the write is under sk_receive_queue->lock but the read
is done as lockless. so fix it by using skb_queue_empty_lockless()
instead of skb_queue_empty() for the read in netlink_rcv_wake()
David S. Miller [Fri, 28 Aug 2020 13:16:48 +0000 (06:16 -0700)]
Merge tag 'mac80211-for-davem-2020-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have:
* fixes for AQL (airtime queue limits)
* reduce packet loss detection false positives
* a small channel number fix for the 6 GHz band
* a fix for 80+80/160 MHz negotiation
* an nl80211 attribute (NL80211_ATTR_HE_6GHZ_CAPABILITY) fix
* add a missing sanity check for the regulatory code
====================
vdso32 should only be installed if CONFIG_COMPAT_VDSO is enabled,
since it's not even supposed to be compiled otherwise, and arm64
builds without a 32bit crosscompiler will fail.
Sean Young [Thu, 13 Aug 2020 09:08:49 +0000 (11:08 +0200)]
media: gpio-ir-tx: spinlock is not needed to disable interrupts
During bit-banging the IR on a gpio pin, we cannot be scheduled or have
anything interrupt us, else the generated signal will be incorrect.
Therefore, we need to disable interrupts on the local cpu. This also
disables preemption.
local_irq_disable() does exactly what we need and does not require a
spinlock.
Sean Young [Sat, 8 Aug 2020 11:38:02 +0000 (13:38 +0200)]
media: rc: do not access device via sysfs after rc_unregister_device()
Device drivers do not expect to have change_protocol or wakeup
re-programming to be accesed after rc_unregister_device(). This can
cause the device driver to access deallocated resources.
When stdout output from the selftests tool 'test_maps' gets redirected
into e.g file or pipe, then the output lines increase a lot (from 21
to 33949 lines). This is caused by the printf that happens before the
fork() call, and there are user-space buffered printf data that seems
to be duplicated into the forked process.
To fix this fflush() stdout before the fork loop in __run_parallel().
Andy Shevchenko [Mon, 3 Aug 2020 08:27:06 +0000 (11:27 +0300)]
kobject: Restore old behaviour of kobject_del(NULL)
The commit 079ad2fb4bf9 ("kobject: Avoid premature parent object freeing in
kobject_cleanup()") inadvertently dropped a possibility to call kobject_del()
with NULL pointer. Restore the old behaviour.
Sami Tolvanen [Thu, 27 Aug 2020 20:36:08 +0000 (13:36 -0700)]
arm64: use a common .arch preamble for inline assembly
Commit 7c78f67e9bd9 ("arm64: enable tlbi range instructions") breaks
LLVM's integrated assembler, because -Wa,-march is only passed to
external assemblers and therefore, the new instructions are not enabled
when IAS is used.
This change adds a common architecture version preamble, which can be
used in inline assembly blocks that contain instructions that require
a newer architecture version, and uses it to fix __TLBI_0 and __TLBI_1
with ARM64_TLB_RANGE.
Sakari Ailus [Mon, 3 Aug 2020 09:07:06 +0000 (11:07 +0200)]
media: max9286: Depend on OF_GPIO
The driver expects struct gpio_chip has of_node field and that field is
only there if CONFIG_OF_GPIO is defined. Fix this by changing the OF
dependency to OF_GPIO.
Jacopo Mondi [Mon, 22 Jun 2020 16:43:52 +0000 (18:43 +0200)]
media: i2c: imx214: select V4L2_FWNODE
After the recent conversion of the media build infrastructure to select
V4L2 components instead of depending on their presence, which took place
in: 32a363d0b0b14 ("media: Kconfig files: use select for V4L2 subdevs and MC")
imx214 stands out as being the (only?) media I2C driver that still depends
on a V4L2 core symbol instead of selecting it.
This confuses the build system which claims it has detected a circular
dependency when other drivers select the same symbol as the imx214
driver does.
drivers/media/i2c/Kconfig:728:error: recursive dependency detected!
drivers/media/i2c/Kconfig:728: symbol VIDEO_IMX214 depends on V4L2_FWNODE
drivers/media/v4l2-core/Kconfig:71: symbol V4L2_FWNODE is selected by VIDEO_BCM2835_UNICAM
drivers/media/platform/bcm2835/Kconfig:3: symbol VIDEO_BCM2835_UNICAM depends on VIDEO_V4L2_SUBDEV_API
drivers/media/v4l2-core/Kconfig:19: symbol VIDEO_V4L2_SUBDEV_API depends on MEDIA_CONTROLLER
drivers/media/Kconfig:168: symbol MEDIA_CONTROLLER is selected by VIDEO_IMX214
Fix this by making the imx214 driver select V4L2_FWNODE instead of
depending on it and align it with all the other drivers.
Fixes: 32a363d0b0b14 ("media: Kconfig files: use select for V4L2 subdevs and MC") Reviewed-by: Laurent Pinchart <[email protected]> Signed-off-by: Jacopo Mondi <[email protected]> Signed-off-by: Sakari Ailus <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
Lee Jones [Wed, 19 Aug 2020 08:16:50 +0000 (09:16 +0100)]
mfd: mfd-core: Ensure disabled devices are ignored without error
Commit e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match
devices with the correct of_nodes") changed the semantics for disabled
devices in mfd_add_device(). Instead of silently ignoring a disabled
child device, an error was returned. On receipt of the error
mfd_add_devices() the precedes to remove *all* child devices and
returns an all-failed error to the caller, which will inevitably fail
the parent device as well.
This patch reverts back to the old semantics and ignores child devices
which are disabled in Device Tree.
Fixes: e49aa9a9bd22 ("mfd: core: Make a best effort attempt to match devices with the correct of_nodes") Reported-by: Icenowy Zheng <[email protected]> Tested-by: Icenowy Zheng <[email protected]> Signed-off-by: Lee Jones <[email protected]>
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
projects / linux.git / log