Antonio Ospite [Thu, 14 Apr 2011 22:21:59 +0000 (15:21 -0700)]
leds/leds-regulator.c: fix handling of already enabled regulators
Make the driver aware of the initial status of the regulator.
The leds-regulator driver was ignoring the initial status of the
regulator; this resulted in rdev->use_count being incremented to 2 after
calling regulator_led_set_value() in the .probe method when a regulator
was already enabled at insmod time, which made it impossible to ever
disable the regulator.
The memory hotplug case involves calling to build_all_zonelists() which
in turns calls in to setup_zone_pageset(). The latter is marked
__meminit while build_all_zonelists() itself has no particular
annotation. build_all_zonelists() is only handed a non-NULL pointer in
the case of memory hotplug through an existing __meminit path, so the
setup_zone_pageset() reference is always safe.
The options as such are either to flag build_all_zonelists() as __ref (as
per __build_all_zonelists()), or to simply discard the __meminit
annotation from setup_zone_pageset().
Timo Warns [Thu, 14 Apr 2011 22:21:56 +0000 (15:21 -0700)]
fs/partitions/ldm.c: fix oops caused by corrupted partition table
The kernel automatically evaluates partition tables of storage devices.
The code for evaluating LDM partitions (in fs/partitions/ldm.c) contains
a bug that causes a kernel oops on certain corrupted LDM partitions.
A kernel subsystem seems to crash, because, after the oops, the kernel no
longer recognizes newly connected storage devices.
Daniel Kiper [Thu, 14 Apr 2011 22:21:53 +0000 (15:21 -0700)]
mm: optimize pfn calculation in online_page()
If CONFIG_FLATMEM is enabled pfn is calculated in online_page() more than
once. It is possible to optimize that and use value established at
beginning of that function.
Eric Dumazet [Thu, 14 Apr 2011 22:21:52 +0000 (15:21 -0700)]
memcg: fix mem_cgroup_rotate_reclaimable_page()
commit 3f58a8294333 ("move memcg reclaimable page into tail of inactive
list") added inline keyword twice in its prototype.
CC arch/x86/kernel/asm-offsets.s
In file included from include/linux/swap.h:8,
from include/linux/suspend.h:4,
from arch/x86/kernel/asm-offsets.c:12:
include/linux/memcontrol.h:220: error: duplicate `inline'
To quote Richard:
I don't think this should be mainlined. It was a
misunderstanding on my part. If you see all the other hdc
drivers in the same location, they all do the same thing (i.e.
clear the interrupt status first, then do the work) that
"glitch" I think I saw was actually two back-to-back
interrupts.
Sebastian (the original author of isp1760) explained it to me a
few days after my submission.
Nicolas Pitre [Wed, 13 Apr 2011 04:01:52 +0000 (05:01 +0100)]
ARM: 6879/1: fix personality test wrt usage of domain handlers
There are optional bits that may complement a personality ID. It is
therefore wrong to simply test against the absolute current->personality
value to determine the effective personality. The PER_LINUX_32BIT is
itself just PER_LINUX with one of those optional bits set.
Nicolas Pitre [Wed, 13 Apr 2011 03:59:36 +0000 (04:59 +0100)]
ARM: 6878/1: fix personality flag propagation across an exec
Our SET_PERSONALITY() implementation was overwriting all existing
personality flags, including ADDR_NO_RANDOMIZE, making them unavailable
to processes being exec'd after a call to personality() in user space.
This prevents the gdb test suite from running successfully.
This config option isn't actually used anywhere and can be safely
removed. The last user was traps.c before commit 082f47a ([ARM]
always allow dump_stack() to produce a backtrace, 2007-07-05).
ARM: SAMSUNG: Fix warning 's3c_pm_show_resume_irqs' defined but not used
s3c_pm_show_resume_irqs() is used by some s3c_pm_arch_show_resume_irqs()
implementations, which get included through mach/pm-core.h. Add __maybe_unused
to silence warnings when it isn't used (e.g. on S3C64XX platforms).
Abhilash Kesavan [Fri, 25 Mar 2011 08:45:19 +0000 (17:45 +0900)]
ARM: SAMSUNG: Fix build failure in PM CRC check code
This patch fixes build error that occurs on enabling the Samsung
specific PM CRC check code. Missed removing this reference of
s3c_sleep_save_phys during move to generic cpu suspend/resume
support.
Andiry Xu [Tue, 22 Mar 2011 09:08:14 +0000 (17:08 +0800)]
xHCI: Implement AMD PLL quirk
This patch disable the optional PM feature inside the Hudson3 platform under
the following conditions:
1. If an isochronous device is connected to xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
The PM feature needs to be disabled to eliminate PLL startup delays when the
link comes out of low power state. The performance of DMA data transfer could
be impacted if system delay were encountered and in addition to the PLL start
up delays. Disabling the PM would leave room for unpredictable system delays
in order to guarantee uninterrupted data transfer to isochronous audio or
video stream devices that require time sensitive information. If data in an
audio/video stream was interrupted then erratic audio or video performance
may be encountered.
AMD PLL quirk is already implemented in OHCI/EHCI driver. After moving the
quirk code to pci-quirks.c and export them, xHCI driver can call it directly
without having the quirk implementation in itself.
Sarah Sharp [Wed, 13 Apr 2011 00:43:19 +0000 (17:43 -0700)]
xhci: Tell USB core both roothubs lost power.
On a resume, when the power is lost during hibernate, the USB core will
call hub_reset_resume for the xHCI USB 2.0 roothub, but not for the USB
3.0 roothub:
[ 164.748310] usb usb1: root hub lost power or was reset
[ 164.748353] usb usb2: root hub lost power or was reset
[ 164.748487] usb usb3: root hub lost power or was reset
[ 164.748488] xhci_hcd 0000:01:00.0: Stop HCD
...
[ 164.870039] hub 4-0:1.0: hub_resume
...
[ 164.870054] hub 3-0:1.0: hub_reset_resume
This causes issues later, because the USB core assumes the USB 3.0 hub
attached to the USB 3.0 roothub is still active. It attempts to queue a
control URB for the external hub, which fails because all the device
slot contexts were released when the USB 3.0 roothub lost power:
[ 164.980044] hub 4-1:1.0: hub_resume
[ 164.980047] xhci_hcd 0000:01:00.0: Get port status returned 0x10101
[ 164.980049] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980053] hub 3-0:1.0: port 1: status 0101 change 0001
[ 164.980056] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980060] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc90008948440, 32'h202e1, 4'hf);
[ 164.980062] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980066] xhci_hcd 0000:01:00.0: clear port connect change, actual port 0 status = 0x2e1
[ 164.980069] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980072] xhci_hcd 0000:01:00.0: get port status, actual port 1 status = 0x2a0
[ 164.980074] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980077] xhci_hcd 0000:01:00.0: Get port status returned 0x100
[ 164.980079] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980082] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980085] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980088] hub 4-1:1.0: port 4: status 0000 change 0000
[ 164.980091] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980094] hub 4-1:1.0: activate --> -22
[ 164.980113] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980117] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980119] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980123] hub 4-1:1.0: can't resume port 4, status -22
[ 164.980126] hub 4-1:1.0: port 4 status ffff.ffff after resume, -22
[ 164.980129] usb 4-1.4: can't resume, status -22
[ 164.980131] hub 4-1:1.0: logical disconnect on port 4
This causes issues when a USB 3.0 hard drive is attached to the external
USB 3.0 hub when the system is hibernated:
Matthew Wilcox [Tue, 28 Sep 2010 04:57:32 +0000 (00:57 -0400)]
USB: Fix unplug of device with active streams
If I unplug a device while the UAS driver is loaded, I get an oops
in usb_free_streams(). This is because usb_unbind_interface() calls
usb_disable_interface() which calls usb_disable_endpoint() which sets
ep_out and ep_in to NULL. Then the UAS driver calls usb_pipe_endpoint()
which returns a NULL pointer and passes an array of NULL pointers to
usb_free_streams().
I think the correct fix for this is to check for the NULL pointer
in usb_free_streams() rather than making the driver check for this
situation. My original patch for this checked for dev->state ==
USB_STATE_NOTATTACHED, but the call to usb_disable_interface() is
conditional, so not all drivers would want this check.
Note from Sarah Sharp: This patch does avoid a potential dereference,
but the real fix (which will be implemented later) is to set the
.soft_unbind flag in the usb_driver structure for the UAS driver, and
all drivers that allocate streams. The driver should free any streams
when it is unbound from the interface. This avoids leaking stream rings
in the xHCI driver when usb_disable_interface() is called.
This should be queued for stable trees back to 2.6.35.
USB: xhci - also free streams when resetting devices
Currently, when resetting a device, xHCI driver disables all but one
endpoints and frees their rings, but leaves alone any streams that
might have been allocated. Later, when users try to free allocated
streams, we oops in xhci_setup_no_streams_ep_input_ctx() because
ep->ring is NULL.
Let's free not only rings but also stream data as well, so that
calling free_streams() on a device that was reset will be safe.
This should be queued for stable trees back to 2.6.35.
Sonic Zhang [Tue, 12 Apr 2011 08:16:04 +0000 (08:16 +0000)]
Blackfin: SMP: fix cache flush loop
The recent commit (10774912647781) wasn't entirely correct. While
it fixed some issues, it introduced others. So pull in the fixes
from the public cache flush functions, and document why we need to
call things directly ourselves.
Graf Yang [Thu, 7 Jan 2010 06:57:30 +0000 (06:57 +0000)]
Blackfin: SMP: make all barriers handle cache issues
When suspending/resuming, the common task freezing code will run in
parallel and freeze processes on each core. This is because the code
uses the non-smp version of memory barriers (as well it should).
The Blackfin smp barrier logic at the moment contains the cache sync
logic, but the non-smp barriers do not. This is incorrect as Rafel
summarized:
> ...
> The existing memory barriers are SMP barriers too, but they are more
> than _just_ SMP barriers. At least that's how it is _supposed_ to be
> (eg. rmb() is supposed to be stronger than smp_rmb()).
> ...
> However, looking at the blackfin's definitions of SMP barriers I see
> that it uses extra stuff that should _also_ be used in the definitions
> of the mandatory barriers.
> ...
Sarah Sharp [Thu, 24 Mar 2011 15:02:58 +0000 (08:02 -0700)]
xhci: Fix NULL pointer deref in handle_port_status()
When we get a port status change event, we need to figure out what type of
port it came from: a USB 3.0 port, or a USB 2.0/1.1 port. We can't know
which usb_hcd to use until that point, so hcd will be NULL for part of the
function. Unfortunately, if any of the sanity checks fail, we'll jump to
the cleanup label before hcd is set to a valid pointer, and then we'll
attempt to tell the USB core to kick the hcd, which is NULL.
Skip kicking the roothub if the sanity checks fail.
Dmitry Torokhov [Thu, 24 Mar 2011 05:41:23 +0000 (22:41 -0700)]
USB: xhci - fix math in xhci_get_endpoint_interval()
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Dmitry Torokhov [Thu, 24 Mar 2011 03:47:05 +0000 (20:47 -0700)]
USB: xhci: simplify logic of skipping missed isoc TDs
The logic of the handling Missed Service Error Events was pretty
confusing as we were checking the same condition several times.
In addition, it caused compiler warning since the compiler could
not figure out that event_trb is actually unused in case we are
skipping current TD.
Fix that by rearranging "skip" condition checks, and factor out
skip_isoc_td() so that it is called explicitly.
Dan Carpenter [Thu, 17 Mar 2011 19:39:49 +0000 (22:39 +0300)]
USB: xhci: unsigned char never equals -1
There were some places that compared port_speed == -1 where port_speed
is a u8. This doesn't work unless we cast the -1 to u8. Some places
did it correctly.
Instead of using -1 directly, I've created a DUPLICATE_ENTRY define
which does the cast and is more descriptive as well.
USB: isp1760-hcd: move imask clear after pending work is done
This patch moves the HcInterrupt register write to clear the
pending interrupt to after the isr work is done, doing this removes
glitches in the irq line.
USB: fsl_qe_udc: send ZLP when zero flag and length % maxpacket == 0
The driver did not take the zero flag in the USB request. If the
request length is the same as the endpoint's maxpacket, an additional
ZLP with no data has to be transmitted.
The method used here is inspired to what is done in fsl_udc_core.c
(and pxa27x_udc.c and at91_udc.c) where this is supported.
There already was a discussion about this topic with people from
Keymile, and I propose here a better implementation:
Steven Hardy [Mon, 4 Apr 2011 17:02:25 +0000 (18:02 +0100)]
usb: qcserial add missing errorpath kfrees
There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Steven Hardy [Mon, 4 Apr 2011 16:59:55 +0000 (17:59 +0100)]
usb: qcserial avoid pointing to freed memory
Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Steven Hardy [Mon, 4 Apr 2011 16:57:37 +0000 (17:57 +0100)]
usb: Fix qcserial memory leak on rmmod
qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Dan Carpenter [Sun, 20 Mar 2011 11:09:50 +0000 (14:09 +0300)]
usb: pch_udc: unlock on allocation failure
There was an unlock missing on the error path.
Also I did a small cleanup by changing ep->dev->lock for just dev->lock.
They're the same lock, but dev->lock is shorter and that's how it is
used for the spin_unlock_irqrestore() call.
It turns out that this function calls pci_get_device under a spin_lock
with irqs disabled, but the pci_get_device function is only allowed in
preemptible context.
This patch fixes the warning by making all data-structure
modifications on temporal storage and commiting this back
into the visible structure at the end. While at it, this
patch also moves the pci_dev_put calls out of the spinlocks
because this function might sleep too.
Johan Hovold [Tue, 5 Apr 2011 17:50:34 +0000 (19:50 +0200)]
usb: musb: omap2430: fix build failure
Fix build failure introduced by commit 7acc6197b76edd0b932a7cbcc6cfad0a8a87f026 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.
CC drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Alan Stern [Tue, 5 Apr 2011 17:36:15 +0000 (13:36 -0400)]
USB: EHCI: unlink unused QHs when the controller is stopped
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.
Using the cloned skb and freeing the skb in the completion callback
for usb request.
USB: usb-gadget: unlock data->lock mutex on error path in ep_read()
ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
Found by Linux Driver Verification project (linuxtesting.org).
Merge branch 'for-greg' of git://gitorious.org/usb/usb into usb-linus
* 'for-greg' of git://gitorious.org/usb/usb:
USB: musb: blackfin: work around anomaly 05000450
usb: musb: Fix the crash issue during reboot
usb: musb: gadget: check the correct list_head
usb: musb: temporarily make it bool
USB: musb: dereferencing an iomem pointer
USB: musb: silence printk format warning
USB: musb: using 0 instead of NULL
USB: musb: add missing unlock in cppi_interrupt()
usb: musb: ux500: copy dma mask from platform device to musb device
usb: musb: clear AUTOSET while clearing DMAENAB
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6:
avr32: add ATAG_BOARDINFO
don't check platform_get_irq's return value against zero
avr32: init cannot ignore signals sent by force_sig_info()
avr32: fix deadlock when reading clock list in debugfs
avr32: Fix .size directive for cpu_enter_idle
avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
fix the wrong argument of the functions definition
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
Revert "i915: restore only the mode of this driver on lastclose"
Revert "ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set."
i915: select VIDEO_OUTPUT_CONTROL for ACPI_VIDEO
drm/radeon/kms: properly program vddci on evergreen+
drm/radeon/kms: add voltage type to atom set voltage function
drm/radeon/kms: fix pcie_p callbacks on btc and cayman
drm/radeon/kms: fix suspend on rv530 asics
drm/radeon/kms: clean up gart dummy page handling
drm/radeon/kms: make radeon i2c put/get bytes less noisy
drm/radeon/kms: pll tweaks for rv6xx
drm/radeon: Fix KMS legacy backlight support if CONFIG_BACKLIGHT_CLASS_DEVICE=m.
radeon: Fix KMS CP writeback on big endian machines.
i915: restore only the mode of this driver on lastclose
drm/nvc0: improve vm flush function
drm/nv50-nvc0: remove some code that doesn't belong here
drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
drm/nouveau: quirk for XFX GT-240X-YA
drm/nv50-nvc0: work around an evo channel hang that some people see
drm/nouveau: implement init table opcode 0x5c
drm/nouveau: fix oops on unload with disabled LVDS panel
...
block: don't flush plugged IO on forced preemtion scheduling
We really only want to unplug the pending IO when the process actually
goes to sleep. So move the test for flushing the plug up to the place
where we actually deactivate the task - where we have properly checked
for preemption and for the process really sleeping.
Commit 982134ba6261 ("mm: avoid wrapping vm_pgoff in mremap()") fixed
the case of a expanding mapping causing vm_pgoff wrapping when you used
mremap. But there was another case where we expand mappings hiding in
plain sight: the automatic stack expansion.
This fixes that case too.
This one also found by Robert Święcki, using his nasty system call
fuzzer tool. Good job.
Andreas Bießmann [Wed, 13 Apr 2011 08:07:35 +0000 (10:07 +0200)]
avr32: add ATAG_BOARDINFO
The ATAG_BOARDINFO is intended to hand over the information
bd->bi_board_number from u-boot to the kernel.
This piece of information can be used to implement some kind of board
identification while booting the kernel. Therefore it is placed in .initdata
section and can be accessed via the new symbol board_number only while
initializing the kernel.
don't check platform_get_irq's return value against zero
platform_get_irq returns -ENXIO on failure, so !int_irq was probably
always true. Better use (int)int_irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
Matt Fleming [Mon, 4 Apr 2011 14:58:04 +0000 (15:58 +0100)]
avr32: init cannot ignore signals sent by force_sig_info()
We can delete the code that checks to see if we're sending an ignored
signal to init because force_sig_info() already handles this case.
force_sig_info() will kill init even if the signal handler is SIG_DFL
and the scenario described in the comment where init might "generate
the same exception over and over again" cannot occur (force_sig_info()
clears SIGNAL_UNKILLABLE to ensure that init will die).
Also, the use of is_global_init() is not correct in the multhreaded
case, as Oleg Nesterov explains,
"is_global_init() is not right in theory, /sbin/init can be
multithreaded. And, this doesn't cover the sub-namespace
inits... I'd suggest to check SIGNAL_UNKILLABLE, but looking
closer I think you can simply remove this code."
It seems this code was copied from arch/powerpc in March 2007 in commit
623b0355d5b1 "[AVR32] Clean up exception handling code"
but the code was deleted from arch/powerpc in November 2009 in commit
a0592d42fe3e "powerpc: kill the obsolete code under is_global_init()"
So catch up with powerpc and delete the bogus code.
avr32: fix deadlock when reading clock list in debugfs
When writing out /sys/kernel/debug/at32ap_clk, clock list lock is being
held while clk_get() is called. clk_get() attempts to take the same
lock, which results in deadlock. Introduce and call lock free version,
__clk_get(), instead.
Maksim Rayskiy [Tue, 12 Apr 2011 22:14:56 +0000 (15:14 -0700)]
UBIFS: fix compilation warnings when compiling with gcc 4.5
When compiling UBIFS with CONFIG_UBIFS_FS_DEBUG not set,
gcc-4.5.2 generates a slew of "warning: statement with no effect"
on references to non-void functions defined as 0.
To avoid these warnings, replace #defines with dummy inline functions.
Artem: massage the patch a bit, also remove the duplicate
'dbg_check_lprops()' prototype.
DMA mode 1 data corruption anomaly on Blackfin systems. This issue is
specific to the Blackfin silicon as the bug appears to be related to the
connection of the musb ip to the bus/dma fabric.
Data corruption when using USB DMA mode 1. (Issue manager 17-01-0105)
DMA mode 1 allows large size transfers to generate a single interrupt
at the end of the entire transfer. The transfer is split up in packets
of length specified in the Maximum Packet Size field for that endpoint.
If the transfer size is not an integer multiple of the Maximum Packet
Size, a short packet will be present at the end of the transfer.
Under certain conditions this packet may be corrupted in the USB FIFO.
Workaround:
Use DMA mode 1 to transfer (n* Maximum Packet Size) and schedule DMA
mode 0 to transfer the short packet.
As an example if your transfer size is 33168 bytes and Maximum Packet
Size equals 512, schedule [33168 - (33168 mod 512)] in DMA mode 1 and
the remainder (33168 mod 512) in DMA mode 0.
The musb clock was disabled when musb_shutdown() was called by
platform_drv_shutdown in which there are register accesses.
call pm_runtime_get_sync() and pm_runtime_put_sync() in the
musb_shutdown function.
Felipe Balbi [Tue, 22 Mar 2011 09:31:37 +0000 (11:31 +0200)]
usb: musb: temporarily make it bool
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Dan Carpenter [Sun, 20 Mar 2011 11:18:26 +0000 (14:18 +0300)]
USB: musb: dereferencing an iomem pointer
"tx_ram" points to io memory. We can't dereference it directly. Sparse
complains about this: "drivers/usb/musb/cppi_dma.c:1205:25: warning:
dereference of noderef expression"
Dan Carpenter [Sun, 20 Mar 2011 11:16:17 +0000 (14:16 +0300)]
USB: musb: silence printk format warning
Gcc gives the following warnings:
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_tx_segment’:
drivers/usb/musb/cppi_dma.c:600: warning: format ‘%x’ expects type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_rx_segment’:
drivers/usb/musb/cppi_dma.c:822: warning: format ‘%x’ expects type ‘unsigned int’, but argument 9 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_rx_scan’:
drivers/usb/musb/cppi_dma.c:1042: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c:1114: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 7 has type ‘dma_addr_t’
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them
to unsigned long long for printk().
On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
This patch fixes severe UBIFS bug: UBIFS oopses when we 'fsync()' an
file on R/O-mounter file-system. We (the UBIFS authors) incorrectly
thought that VFS would not propagate 'fsync()' down to the file-system
if it is read-only, but this is not the case.
It is easy to exploit this bug using the following simple perl script:
use strict;
use File::Sync qw(fsync sync);
die "File path is not specified" if not defined $ARGV[0];
my $path = $ARGV[0];
open FILE, "<", "$path" or die "Cannot open $path: $!";
fsync(\*FILE) or die "cannot fsync $path: $!";
close FILE or die "Cannot close $path: $!";
Thanks to Reuben Dowle <[email protected]> for reporting about this
issue.
Jeff Brown [Wed, 13 Apr 2011 06:29:38 +0000 (23:29 -0700)]
Input: evdev - indicate buffer overrun with SYN_DROPPED
Add a new EV_SYN code, SYN_DROPPED, to inform the client when input
events have been dropped from the evdev input buffer due to a
buffer overrun. The client should use this event as a hint to
reset its state or ignore all following events until the next
packet begins.
Jarod Wilson [Wed, 13 Apr 2011 06:13:08 +0000 (23:13 -0700)]
Input: add KEY_IMAGES specifically for AL Image Browser
Many media center remotes have buttons intended for jumping straight to
one type of media browser or another -- commonly, images/photos/pictures,
audio/music, television, and movies. At present, remotes with an images
or photos or pictures button use any number of different keycodes which
sort of maybe fit. I've seen at least KEY_MEDIA, KEY_CAMERA,
KEY_GRAPHICSEDITOR and KEY_PRESENTATION. None of those seem quite right.
In my mind, KEY_MEDIA should be something more like a media center
application launcher (and I'd like to standardize on that for things
like the windows media center button on the mce remotes). KEY_CAMERA is
used in a lot of webcams, and typically means "take a picture now".
KEY_GRAPHICSEDITOR implies an editor, not a browser. KEY_PRESENTATION
might be the closest fit here, if you think "photo slide show", but it
may well be more intended for "run application in full-screen
presentation mode" or to launch something like magicpoint, I dunno.
And thus, I'd like to have a KEY_IMAGES, which matches the HID Usage AL
Image Browser, the meaning of which I think is crystal-clear. I believe
AL Audio Browser is already covered by KEY_AUDIO, and AL Movie Browser
by KEY_VIDEO, so I'm also adding appropriate comments next to those
keys.
Eric Miao [Tue, 12 Apr 2011 10:39:39 +0000 (18:39 +0800)]
ARM: pxa: convert incorrect IRQ_TO_IRQ() to irq_to_gpio()
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Chris Mason [Tue, 12 Apr 2011 17:57:39 +0000 (13:57 -0400)]
Btrfs: make uncache_state unconditional
The extent_io code can take cached pointers into the extent state trees,
and these can make lookups much faster in common operations. The
caching only happens when specific bits are set that prevent merging
and splitting of the extent state.
A help function was added to uncache the state, and it was testing
the same set of conditionals. This can leak in very strange corner
cases where the lock bit goes away unexpectedly.
The uncaching should be unconditional. Once we have a ref on the
extent we should always give it up.
(DRM_I915 && STUB_POULSBO) selects ACPI_VIDEO which has unmet direct dependencies
(ACPI && X86 && BACKLIGHT_CLASS_DEVICE && VIDEO_OUTPUT_CONTROL && INPUT)
Alex Deucher [Tue, 12 Apr 2011 18:49:24 +0000 (14:49 -0400)]
drm/radeon/kms: properly program vddci on evergreen+
Change vddci as well as vddc when changing power modes
on evergreen/ni. Also, properly set vddci on boot up
for ni cards. The vbios only sets the limited clocks
and voltages on boot until the mc ucode is loaded. This
should fix stability problems on some btc cards.
Alex Deucher [Tue, 12 Apr 2011 17:33:27 +0000 (13:33 -0400)]
drm/radeon/kms: fix suspend on rv530 asics
Apparently only rv515 asics need the workaround
added in f24d86f1a49505cdea56728b853a5d0a3f8e3d11
(drm/radeon/kms: fix resume regression for some r5xx laptops).
Alex Deucher [Tue, 12 Apr 2011 17:32:13 +0000 (13:32 -0400)]
drm/radeon/kms: clean up gart dummy page handling
As per Konrad's original patch, the dummy page used
by the gart code and allocated in radeon_gart_init()
was not freed properly in radeon_gart_fini().
At the same time r6xx and newer allocated and freed the
dummy page on their own. So to do Konrad's patch one
better, just remove the allocation and freeing of the
dummy page in the r6xx, 7xx, evergreen, and ni code and
allocate and free in the gart_init/fini() functions for
all asics.
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: don't allow mmap'ed pages to be dirtied while under writeback (try #3)
[CIFS] Warn on requesting default security (ntlm) on mount
[CIFS] cifs: clarify the meaning of tcpStatus == CifsGood
cifs: wrap received signature check in srv_mutex
cifs: clean up various nits in unicode routines (try #2)
cifs: clean up length checks in check2ndT2
cifs: set ra_pages in backing_dev_info
cifs: fix broken BCC check in is_valid_oplock_break
cifs: always do is_path_accessible check in cifs_mount
various endian fixes to cifs
Elminate sparse __CHECK_ENDIAN__ warnings on port conversion
Max share size is too small
Allow user names longer than 32 bytes
cifs: replace /proc/fs/cifs/Experimental with a module parm
cifs: check for private_data before trying to put it
projects / linux.git / log