Yufen Yu [Tue, 29 Jan 2019 08:34:04 +0000 (16:34 +0800)]
floppy: check_events callback should not return a negative number
floppy_check_events() is supposed to return bit flags to say which
events occured. We should return zero to say that no event flags are
set. Only BIT(0) and BIT(1) are used in the caller. And .check_events
interface also expect to return an unsigned int value.
However, after commit a0c80efe5956, it may return -EINTR (-4u).
Here, both BIT(0) and BIT(1) are cleared. So this patch shouldn't
affect runtime, but it obviously is still worth fixing.
Björn Töpel [Tue, 12 Feb 2019 07:51:14 +0000 (08:51 +0100)]
xsk: do not remove umem from netdevice on fall-back to copy-mode
Commit c9b47cc1fabc ("xsk: fix bug when trying to use both copy and
zero-copy on one queue id") stores the umem into the netdev._rx
struct. However, the patch incorrectly removed the umem from the
netdev._rx struct when user-space passed "best-effort" mode
(i.e. select the fastest possible option available), and zero-copy
mode was not available. This commit fixes that.
Fixes: c9b47cc1fabc ("xsk: fix bug when trying to use both copy and zero-copy on one queue id") Signed-off-by: Björn Töpel <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
Jani Nikula [Fri, 8 Feb 2019 18:42:53 +0000 (20:42 +0200)]
drm/i915/opregion: rvda is relative from opregion base in opregion 2.1+
Starting from opregion version 2.1 (roughly corresponding to ICL+) the
RVDA field is relative from the beginning of opregion, not absolute
address.
Fix the error path while at it.
v2: Make relative vs. absolute conditional on the opregion version,
bumped for the purpose. Turned out there are machines relying on
absolute RVDA in the wild.
Lyude Paul [Tue, 29 Jan 2019 19:09:59 +0000 (14:09 -0500)]
drm/i915: Block fbdev HPD processing during suspend
When resuming, we check whether or not any previously connected
MST topologies are still present and if so, attempt to resume them. If
this fails, we disable said MST topologies and fire off a hotplug event
so that userspace knows to reprobe.
However, sending a hotplug event involves calling
drm_fb_helper_hotplug_event(), which in turn results in fbcon doing a
connector reprobe in the caller's thread - something we can't do at the
point in which i915 calls drm_dp_mst_topology_mgr_resume() since
hotplugging hasn't been fully initialized yet.
This currently causes some rather subtle but fatal issues. For example,
on my T480s the laptop dock connected to it usually disappears during a
suspend cycle, and comes back up a short while after the system has been
resumed. This guarantees pretty much every suspend and resume cycle,
drm_dp_mst_topology_mgr_set_mst(mgr, false); will be caused and in turn,
a connector hotplug will occur. Now it's Rute Goldberg time: when the
connector hotplug occurs, i915 reprobes /all/ of the connectors,
including eDP. However, eDP probing requires that we power on the panel
VDD which in turn, grabs a wakeref to the appropriate power domain on
the GPU (on my T480s, this is the PORT_DDI_A_IO domain). This is where
things start breaking, since this all happens before
intel_power_domains_enable() is called we end up leaking the wakeref
that was acquired and never releasing it later. Come next suspend/resume
cycle, this causes us to fail to shut down the GPU properly, which
causes it not to resume properly and die a horrible complicated death.
(as a note: this only happens when there's both an eDP panel and MST
topology connected which is removed mid-suspend. One or the other seems
to always be OK).
We could try to fix the VDD wakeref leak, but this doesn't seem like
it's worth it at all since we aren't able to handle hotplug detection
while resuming anyway. So, let's go with a more robust solution inspired
by nouveau: block fbdev from handling hotplug events until we resume
fbdev. This allows us to still send sysfs hotplug events to be handled
later by user space while we're resuming, while also preventing us from
actually processing any hotplug events we receive until it's safe.
This fixes the wakeref leak observed on the T480s and as such, also
fixes suspend/resume with MST topologies connected on this machine.
Changes since v2:
* Don't call drm_fb_helper_hotplug_event() under lock, do it after lock
(Chris Wilson)
* Don't call drm_fb_helper_hotplug_event() in
intel_fbdev_output_poll_changed() under lock (Chris Wilson)
* Always set ifbdev->hpd_waiting (Chris Wilson)
Tvrtko Ursulin [Tue, 5 Feb 2019 13:03:53 +0000 (13:03 +0000)]
drm/i915/pmu: Fix enable count array size and bounds checking
Enable count array is supposed to have one counter for each possible
engine sampler. As such, array sizing and bounds checking is not correct
and would blow up the asserts if more samplers were added.
No ill-effect in the current code base but lets fix it for correctness.
At the same time tidy the assert for readability and robustness.
Andrea Claudi [Mon, 11 Feb 2019 15:14:39 +0000 (16:14 +0100)]
ipvs: fix dependency on nf_defrag_ipv6
ipvs relies on nf_defrag_ipv6 module to manage IPv6 fragmentation,
but lacks proper Kconfig dependencies and does not explicitly
request defrag features.
As a result, if netfilter hooks are not loaded, when IPv6 fragmented
packet are handled by ipvs only the first fragment makes through.
Fix it properly declaring the dependency on Kconfig and registering
netfilter hooks on ip_vs_add_service() and ip_vs_new_dest().
Tuong Lien [Mon, 11 Feb 2019 06:29:43 +0000 (13:29 +0700)]
tipc: fix link session and re-establish issues
When a link endpoint is re-created (e.g. after a node reboot or
interface reset), the link session number is varied by random, the peer
endpoint will be synced with this new session number before the link is
re-established.
However, there is a shortcoming in this mechanism that can lead to the
link never re-established or faced with a failure then. It happens when
the peer endpoint is ready in ESTABLISHING state, the 'peer_session' as
well as the 'in_session' flag have been set, but suddenly this link
endpoint leaves. When it comes back with a random session number, there
are two situations possible:
1/ If the random session number is larger than (or equal to) the
previous one, the peer endpoint will be updated with this new session
upon receipt of a RESET_MSG from this endpoint, and the link can be re-
established as normal. Otherwise, all the RESET_MSGs from this endpoint
will be rejected by the peer. In turn, when this link endpoint receives
one ACTIVATE_MSG from the peer, it will move to ESTABLISHED and start
to send STATE_MSGs, but again these messages will be dropped by the
peer due to wrong session.
The peer link endpoint can still become ESTABLISHED after receiving a
traffic message from this endpoint (e.g. a BCAST_PROTOCOL or
NAME_DISTRIBUTOR), but since all the STATE_MSGs are invalid, the link
will be forced down sooner or later!
Even in case the random session number is larger than the previous one,
it can be that the ACTIVATE_MSG from the peer arrives first, and this
link endpoint moves quickly to ESTABLISHED without sending out any
RESET_MSG yet. Consequently, the peer link will not be updated with the
new session number, and the same link failure scenario as above will
happen.
2/ Another situation can be that, the peer link endpoint was reset due
to any reasons in the meantime, its link state was set to RESET from
ESTABLISHING but still in session, i.e. the 'in_session' flag is not
reset...
Now, if the random session number from this endpoint is less than the
previous one, all the RESET_MSGs from this endpoint will be rejected by
the peer. In the other direction, when this link endpoint receives a
RESET_MSG from the peer, it moves to ESTABLISHING and starts to send
ACTIVATE_MSGs, but all these messages will be rejected by the peer too.
As a result, the link cannot be re-established but gets stuck with this
link endpoint in state ESTABLISHING and the peer in RESET!
Solution:
===========
This link endpoint should not go directly to ESTABLISHED when getting
ACTIVATE_MSG from the peer which may belong to the old session if the
link was re-created. To ensure the session to be correct before the
link is re-established, the peer endpoint in ESTABLISHING state will
send back the last session number in ACTIVATE_MSG for a verification at
this endpoint. Then, if needed, a new and more appropriate session
number will be regenerated to force a re-synch first.
In addition, when a link in ESTABLISHING state is reset, its state will
move to RESET according to the link FSM, along with resetting the
'in_session' flag (and the other data) as a normal link reset, it will
also be deleted if requested.
Zhiqiang Liu [Mon, 11 Feb 2019 02:57:46 +0000 (10:57 +0800)]
net: fix IPv6 prefix route residue
Follow those steps:
# ip addr add 2001:123::1/32 dev eth0
# ip addr add 2001:123:456::2/64 dev eth0
# ip addr del 2001:123::1/32 dev eth0
# ip addr del 2001:123:456::2/64 dev eth0
and then prefix route of 2001:123::1/32 will still exist.
This is because ipv6_prefix_equal in check_cleanup_prefix_route
func does not check whether two IPv6 addresses have the same
prefix length. If the prefix of one address starts with another
shorter address prefix, even though their prefix lengths are
different, the return value of ipv6_prefix_equal is true.
Here I add a check of whether two addresses have the same prefix
to decide whether their prefixes are equal.
Fixes: 5b84efecb7d9 ("ipv6 addrconf: don't cleanup prefix route for IFA_F_NOPREFIXROUTE") Signed-off-by: Zhiqiang Liu <[email protected]> Reported-by: Wenhao Zhang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jianchao Wang [Tue, 12 Feb 2019 01:56:25 +0000 (09:56 +0800)]
blk-mq: insert rq with DONTPREP to hctx dispatch list when requeue
When requeue, if RQF_DONTPREP, rq has contained some driver
specific data, so insert it to hctx dispatch list to avoid any
merge. Take scsi as example, here is the trace event log (no
io scheduler, because RQF_STARTED would prevent merging),
(32768 + 8) was requeued by scsi_queue_insert and had RQF_DONTPREP.
Then it was merged with (32776 + 8) and issued. Due to RQF_DONTPREP,
the sdb only contained the part of (32768 + 8), then only that part
was completed. The lucky thing was that scsi_io_completion detected
it and requeued the remaining part. So we didn't get corrupted data.
However, the requeue of (32776 + 8) is not expected.
Hoang Le [Mon, 11 Feb 2019 02:18:28 +0000 (09:18 +0700)]
tipc: fix skb may be leaky in tipc_link_input
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Palmer Dabbelt [Fri, 8 Feb 2019 17:11:08 +0000 (09:11 -0800)]
Revert "RISC-V: Make BSS section as the last section in vmlinux.lds.S"
At least BBL relies on the flat binaries containing all the bytes in the
actual image to exist in the file. Before this revert the flat images
dropped the trailing zeros, which caused BBL to put its copy of the
device tree where Linux thought the BSS was, which wreaks all sorts of
havoc. Manifesting the bug is a bit subtle because BBL aligns
everything to 2MiB page boundaries, but with large enough kernels you're
almost certain to get bitten by the bug.
While moving the sections around isn't a great long-term fix, it will at
least avoid producing broken images.
Stefan O'Rear [Sun, 16 Dec 2018 18:03:36 +0000 (13:03 -0500)]
riscv: Add pte bit to distinguish swap from invalid
Previously, invalid PTEs and swap PTEs had the same binary
representation, causing errors when attempting to unmap PROT_NONE
mappings, including implicit unmap on exit.
Linus Torvalds [Mon, 11 Feb 2019 21:30:50 +0000 (13:30 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC management fixes from Eduardo Valentin:
"Minor fixes on of-thermal and cpu cooling"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: cpu_cooling: Clarify error message
thermal: of-thermal: Print name of device node with error
Andreas Ziegler [Wed, 6 Feb 2019 19:00:13 +0000 (20:00 +0100)]
tracing: probeevent: Correctly update remaining space in dynamic area
Commit 9178412ddf5a ("tracing: probeevent: Return consumed
bytes of dynamic area") improved the string fetching
mechanism by returning the number of required bytes after
copying the argument to the dynamic area. However, this
return value is now only used to increment the pointer
inside the dynamic area but misses updating the 'maxlen'
variable which indicates the remaining space in the dynamic
area.
This means that fetch_store_string() always reads the *total*
size of the dynamic area from the data_loc pointer instead of
the *remaining* size (and passes it along to
strncpy_from_{user,unsafe}) even if we're already about to
copy data into the middle of the dynamic area.
Eric Dumazet [Thu, 7 Feb 2019 20:27:38 +0000 (12:27 -0800)]
vxlan: test dev->flags & IFF_UP before calling netif_rx()
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f957 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Davidlohr Bueso [Mon, 11 Feb 2019 16:15:29 +0000 (08:15 -0800)]
xsk: share the mmap_sem for page pinning
Holding mmap_sem exclusively for a gup() is an overkill. Lets
share the lock and replace the gup call for gup_longterm(), as
it is better suited for the lifetime of the pinning.
The following patchset contains Netfilter fixes for net:
1) Out-of-bound access to packet data from the snmp nat helper,
from Jann Horn.
2) ICMP(v6) error packets are set as related traffic by conntrack,
update protocol number before calling nf_nat_ipv4_manip_pkt()
to use ICMP(v6) rather than the original protocol number,
from Florian Westphal.
====================
Linus Torvalds [Mon, 11 Feb 2019 18:28:48 +0000 (10:28 -0800)]
Merge tag 's390-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 bug fixes from Martin Schwidefsky:
- Fix specification exception on z196 during ap probe
- A fix for suspend-to-disk, the VMAP stack patch broke the
swsusp_arch_suspend function
- The EMC CKD ioctl of the dasd driver needs an additional size check
for user space data
- Revert an incorrect patch for the PCI base code that removed a bit
lock that turned out to be required after all
* tag 's390-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
Revert "s390/pci: remove bit_lock usage in interrupt handler"
s390/zcrypt: fix specification exception on z196 during ap probe
s390/dasd: fix using offset into zero size array error
s390/suspend: fix stack setup in swsusp_arch_suspend
Linus Torvalds [Mon, 11 Feb 2019 18:19:33 +0000 (10:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha fixes from Matt Turner:
"A few changes for alpha, including a build fix, a fix for the Eiger
platform, and a fix for a tricky bug uncovered by the strace test
suite that has existed since at least 1997 (v2.1.32)!"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: fix page fault handling for r16-r18 targets
alpha: Fix Eiger NR_IRQS to 128
tools uapi: fix Alpha support
Mikulas Patocka [Fri, 8 Feb 2019 15:52:07 +0000 (10:52 -0500)]
dm crypt: don't overallocate the integrity tag space
bio_sectors() returns the value in the units of 512-byte sectors (no
matter what the real sector size of the device). dm-crypt multiplies
bio_sectors() by on_disk_tag_size to calculate the space allocated for
integrity tags. If dm-crypt is running with sector size larger than
512b, it allocates more data than is needed.
Device Mapper trims the extra space when passing the bio to
dm-integrity, so this bug didn't result in any visible misbehavior.
But it must be fixed to avoid wasteful memory allocation for the block
integrity payload.
Sander Eikelenboom bisected a NAT related regression down
to the l4proto->manip_pkt indirection removal.
I forgot that ICMP(v6) errors (e.g. PKTTOOBIG) can be set as related
to the existing conntrack entry.
Therefore, when passing the skb to nf_nat_ipv4/6_manip_pkt(), that
ended up calling the wrong l4 manip function, as tuple->dst.protonum
is the original flows l4 protocol (TCP, UDP, etc).
Set the dst protocol field to ICMP(v6), we already have a private copy
of the tuple due to the inversion of src/dst.
Jann Horn [Wed, 6 Feb 2019 21:56:15 +0000 (22:56 +0100)]
netfilter: nf_nat_snmp_basic: add missing length checks in ASN.1 cbs
The generic ASN.1 decoder infrastructure doesn't guarantee that callbacks
will get as much data as they expect; callbacks have to check the `datalen`
parameter before looking at `data`. Make sure that snmp_version() and
snmp_helper() don't read/write beyond the end of the packet data.
(Also move the assignment to `pdata` down below the check to make it clear
that it isn't necessarily a pointer we can use before the `datalen` check.)
Fixes: cc2d58634e0f ("netfilter: nf_nat_snmp_basic: use asn1 decoder library") Signed-off-by: Jann Horn <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
Clint Taylor [Mon, 17 Dec 2018 22:13:47 +0000 (14:13 -0800)]
drm/i915/icl: combo port vswing programming changes per BSPEC
In August 2018 the BSPEC changed the ICL port programming sequence to
closely resemble earlier gen programming sequence. Restrict combo phy to
HBR max rate unless eDP panel is connected to port.
since rw_semaphore is released in a different task vs task that locked the sema.
It is expected behavior.
Fix the warning with up_read_non_owner() and rwsem_release() annotation.
Fixes: bae77c5eb5b2 ("bpf: enable stackmap with build_id in nmi context") Signed-off-by: Alexei Starovoitov <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
Ilan Peer [Wed, 6 Feb 2019 11:17:21 +0000 (13:17 +0200)]
mac80211: Fix Tx aggregation session tear down with ITXQs
When mac80211 requests the low level driver to stop an ongoing
Tx aggregation, the low level driver is expected to call
ieee80211_stop_tx_ba_cb_irqsafe() to indicate that it is ready
to stop the session. The callback in turn schedules a worker
to complete the session tear down, which in turn also handles
the relevant state for the intermediate Tx queue.
However, as this flow in asynchronous, the intermediate queue
should be stopped and not continue servicing frames, as in
such a case frames that are dequeued would be marked as part
of an aggregation, although the aggregation is already been
stopped.
Fix this by stopping the intermediate Tx queue, before
calling the low level driver to stop the Tx aggregation.
Johannes Berg [Wed, 6 Feb 2019 11:17:14 +0000 (13:17 +0200)]
cfg80211: prevent speculation on cfg80211_classify8021d() return
It's possible that the caller of cfg80211_classify8021d() uses the
value to index an array, like mac80211 in ieee80211_downgrade_queue().
Prevent speculation on the return value.
Johannes Berg [Wed, 6 Feb 2019 11:17:07 +0000 (13:17 +0200)]
cfg80211: pmsr: record netlink port ID
Without recording the netlink port ID, we cannot return the
results or complete messages to userspace, nor will we be
able to abort if the socket is closed, so clearly we need
to fill the value.
Johannes Berg [Wed, 6 Feb 2019 11:17:12 +0000 (13:17 +0200)]
mac80211: call drv_ibss_join() on restart
If a driver does any significant activity in its ibss_join method,
then it will very well expect that to be called during restart,
before any stations are added. Do that.
alpha: fix page fault handling for r16-r18 targets
Fix page fault handling code to fixup r16-r18 registers.
Before the patch code had off-by-two registers bug.
This bug caused overwriting of ps,pc,gp registers instead
of fixing intended r16,r17,r18 (see `struct pt_regs`).
More details:
Initially Dmitry noticed a kernel bug as a failure
on strace test suite. Test passes unmapped userspace
pointer to io_submit:
After a page fault `t0` should contain -EFALUT and `a1` is 0.
Instead `gp` was overwritten in place of `a1`.
This happens due to a off-by-two bug in `dpf_reg()` for `r16-r18`
(aka `a0-a2`).
I think the bug went unnoticed for a long time as `gp` is one
of scratch registers. Any kernel function call would re-calculate `gp`.
Dmitry tracked down the bug origin back to 2.1.32 kernel version
where trap_a{0,1,2} fields were inserted into struct pt_regs.
And even before that `dpf_reg()` contained off-by-one error.
Meelis Roos [Fri, 12 Oct 2018 09:27:51 +0000 (12:27 +0300)]
alpha: Fix Eiger NR_IRQS to 128
Eiger machine vector definition has nr_irqs 128, and working 2.6.26
boot shows SCSI getting IRQ-s 64 and 65. Current kernel boot fails
because Symbios SCSI fails to request IRQ-s and does not find the disks.
It has been broken at least since 3.18 - the earliest I could test with
my gcc-5.
The headers have moved around and possibly another order of defines has
worked in the past - but since 128 seems to be correct and used, fix
arch/alpha/include/asm/irq.h to have NR_IRQS=128 for Eiger.
This fixes 4.19-rc7 boot on my Force Flexor A264 (Eiger subarch).
Magnus Karlsson [Fri, 8 Feb 2019 13:13:50 +0000 (14:13 +0100)]
xsk: add missing smp_rmb() in xsk_mmap
All the setup code in AF_XDP is protected by a mutex with the
exception of the mmap code that cannot use it. To make sure that a
process banging on the mmap call at the same time as another process
is setting up the socket, smp_wmb() calls were added in the umem
registration code and the queue creation code, so that the published
structures that xsk_mmap needs would be consistent. However, the
corresponding smp_rmb() calls were not added to the xsk_mmap
code. This patch adds these calls.
Fixes: 37b076933a8e3 ("xsk: add missing write- and data-dependency barrier") Fixes: c0c77d8fb787c ("xsk: add user memory registration support sockopt") Signed-off-by: Magnus Karlsson <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
bpf_skb_change_proto and bpf_skb_adjust_room change skb header length.
For GSO packets they adjust gso_size to maintain the same MTU.
The gso size can only be safely adjusted on bytestream protocols.
Commit d02f51cbcf12 ("bpf: fix bpf_skb_adjust_net/bpf_skb_proto_xlat
to deal with gso sctp skbs") excluded SKB_GSO_SCTP.
Since then type SKB_GSO_UDP_L4 has been added, whose contents are one
gso_size unit per datagram. Also exclude these.
Move from a blacklist to a whitelist check to future proof against
additional such new GSO types, e.g., for fraglist based GRO.
Fixes: bec1f6f69736 ("udp: generate gso with UDP_SEGMENT") Signed-off-by: Willem de Bruijn <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]>
====================
r8169: revert two commits due to a regression
Sander reported a regression (kernel panic, see[1]), therefore let's
revert these commits. Removal of the barriers doesn't seem to
contribute to the issue, the patch just overlaps with the problematic
one and only reverting both patches was tested.
Linus Torvalds [Sun, 10 Feb 2019 18:39:37 +0000 (10:39 -0800)]
Merge tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Fix in at_xdmac fr wrongful channel state
- Fix for imx driver for wrong callback invocation
- Fix to bcm driver for interrupt race & transaction abort.
- Fix in dmatest to abort in mapping error
* tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dmatest: Abort test in case of mapping error
dmaengine: bcm2835: Fix abort of transactions
dmaengine: bcm2835: Fix interrupt race on RT
dmaengine: imx-dma: fix wrong callback invoke
dmaengine: at_xdmac: Fix wrongfull report of a channel as in use
Linus Torvalds [Sun, 10 Feb 2019 17:57:42 +0000 (09:57 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A handful of fixes:
- Fix an MCE corner case bug/crash found via MCE injection testing
- Fix 5-level paging boot crash
- Fix MCE recovery cache invalidation bug
- Fix regression on Xen guests caused by a recent PMD level mremap
speedup optimization"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Make set_pmd_at() paravirt aware
x86/mm/cpa: Fix set_mce_nospec()
x86/boot/compressed/64: Do not corrupt EDX on EFER.LME=1 setting
x86/MCE: Initialize mce.bank in the case of a fatal error in mce_no_way_out()
Linus Torvalds [Sun, 10 Feb 2019 17:54:19 +0000 (09:54 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"irqchip driver fixes: most of them are race fixes for ARM GIC (General
Interrupt Controller) variants, but also a fix for the ARM MMP
(Marvell PXA168 et al) irqchip affecting OLPC keyboards"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Fix ITT_entry_size accessor
irqchip/mmp: Only touch the PJ4 IRQ & FIQ bits on enable/disable
irqchip/gic-v3-its: Gracefully fail on LPI exhaustion
irqchip/gic-v3-its: Plug allocation race for devices sharing a DevID
irqchip/gic-v4: Fix occasional VLPI drop
Linus Torvalds [Sun, 10 Feb 2019 17:48:18 +0000 (09:48 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A couple of kernel side fixes:
- Fix the Intel uncore driver on certain hardware configurations
- Fix a CPU hotplug related memory allocation bug
- Remove a spurious WARN()
... plus also a handful of perf tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf script python: Add Python3 support to tests/attr.py
perf trace: Support multiple "vfs_getname" probes
perf symbols: Filter out hidden symbols from labels
perf symbols: Add fallback definitions for GELF_ST_VISIBILITY()
tools headers uapi: Sync linux/in.h copy from the kernel sources
perf clang: Do not use 'return std::move(something)'
perf mem/c2c: Fix perf_mem_events to support powerpc
perf tests evsel-tp-sched: Fix bitwise operator
perf/core: Don't WARN() for impossible ring-buffer sizes
perf/x86/intel: Delay memory deallocation until x86_pmu_dead_cpu()
perf/x86/intel/uncore: Add Node ID mask
Juergen Gross [Sun, 10 Feb 2019 07:40:56 +0000 (08:40 +0100)]
x86/mm: Make set_pmd_at() paravirt aware
set_pmd_at() calls native_set_pmd() unconditionally on x86. This was
fine as long as only huge page entries were written via set_pmd_at(),
as Xen pv guests don't support those.
Commit 2c91bd4a4e2e53 ("mm: speed up mremap by 20x on large regions")
introduced a usage of set_pmd_at() possible on pv guests, leading to
failures like:
BUG: unable to handle kernel paging request at ffff888023e26778
#PF error: [PROT] [WRITE]
RIP: e030:move_page_tables+0x7c1/0xae0
move_vma.isra.3+0xd1/0x2d0
__se_sys_mremap+0x3c6/0x5b0
do_syscall_64+0x49/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Make set_pmd_at() paravirt aware by just letting it use set_pmd().
from 14 to 18: safe
processed 20 insns (limit 131072), stack depth 48
bpf verifier is misconfigured
Summary: 0 PASSED, 0 SKIPPED, 1 FAILED
The bpf_sock_is_valid_access() is expecting src_ip4 can be narrowly
loaded (meaning load any 1 or 2 bytes of the src_ip4) by
marking info->ctx_field_size. However, this marked
ctx_field_size is not used. This patch fixes it.
Due to the recent refactoring in test_verifier,
this new test will be added to the bpf-next branch
(together with the bpf_tcp_sock patchset)
to avoid merge conflict.
Linus Torvalds [Sat, 9 Feb 2019 21:43:12 +0000 (13:43 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One PM related driver bugfix and a MAINTAINERS update"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
i2c: omap: Use noirq system sleep pm ops to idle device for suspend
Linus Torvalds [Sat, 9 Feb 2019 20:41:14 +0000 (12:41 -0800)]
Merge tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A batch of MIPS fixes for 5.0, nothing too scary.
- A workaround for a Loongson 3 CPU bug is the biggest change, but
still fairly straightforward. It adds extra memory barriers (sync
instructions) around atomics to avoid a CPU bug that can break
atomicity.
- Loongson64 also sees a fix for powering off some systems which
would incorrectly reboot rather than waiting for the power down
sequence to complete.
- We have DT fixes for the Ingenic JZ4740 SoC & the JZ4780-based Ci20
board, and a DT warning fix for the Nexsys4/MIPSfpga board.
- The Cavium Octeon platform sees a further fix to the behaviour of
the pcie_disable command line argument that was introduced in v3.3.
- The VDSO, introduced in v4.4, sees build fixes for configurations
of GCC that were built using the --with-fp-32= flag to specify a
default 32-bit floating point ABI.
- get_frame_info() sees a fix for configurations with
CONFIG_KALLSYMS=n, for which it previously always returned an
error.
- If the MIPS Coherence Manager (CM) reports an error then we'll now
clear that error correctly so that the GCR_ERROR_CAUSE register
will be updated with information about any future errors"
* tag 'mips_fixes_5.0_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
MIPS: Remove function size check in get_frame_info()
MIPS: Use lower case for addresses in nexys4ddr.dts
MIPS: Loongson: Introduce and use loongson_llsc_mb()
MIPS: VDSO: Include $(ccflags-vdso) in o32,n32 .lds builds
MIPS: VDSO: Use same -m%-float cflag as the kernel proper
MIPS: OCTEON: don't set octeon_dma_bar_type if PCI is disabled
DTS: CI20: Fix bugs in ci20's device tree.
MIPS: DTS: jz4740: Correct interrupt number of DMA core
* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
blktrace: Show requests without sector
fs: ratelimit __find_get_block_slow() failure message.
m68k: set proper major_num when specifying module param major_num
libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
aio: initialize kiocb private in case any filesystems expect it.
Linus Torvalds [Sat, 9 Feb 2019 18:17:01 +0000 (10:17 -0800)]
Merge tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
- Fix a problem with the imx28 ECC engine
- Remove a debug trace introduced in 2b6f0090a333 ("mtd: Check
add_mtd_device() ret code")
- Make sure partitions of size 0 can be registered
- Fix kernel-doc warning in the rawnand core
- Fix the error path of spinand_init() (missing manufacturer cleanup in
a few places)
- Address a problem with the SPI NAND PROGRAM LOAD operation which does
not work as expected on some parts.
* tag 'mtd/fixes-for-5.0-rc6' of git://git.infradead.org/linux-mtd:
mtd: rawnand: gpmi: fix MX28 bus master lockup problem
mtd: Make sure mtd->erasesize is valid even if the partition is of size 0
mtd: Remove a debug trace in mtdpart.c
mtd: rawnand: fix kernel-doc warnings
mtd: spinand: Fix the error/cleanup path in spinand_init()
mtd: spinand: Handle the case where PROGRAM LOAD does not reset the cache
Linus Torvalds [Sat, 9 Feb 2019 17:44:08 +0000 (09:44 -0800)]
Merge tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two very minor fixes: one remove of a #include for an unused header
and a fix of the xen ML address in MAINTAINERS"
* tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: unify reference to xen-devel list
arch/arm/xen: Remove duplicate header
Ingo Molnar [Sat, 9 Feb 2019 12:13:45 +0000 (13:13 +0100)]
Merge tag 'perf-urgent-for-mingo-5.0-20190205' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf trace:
Arnaldo Carvalho de Melo:
Fix handling of probe:vfs_getname when the probed routine is
inlined in multiple places, fixing the collection of the 'filename'
parameter in open syscalls.
perf test:
Gustavo A. R. Silva:
Fix bitwise operator usage in evsel-tp-sched test, which made tat
test always detect fields as signed.
Jiri Olsa:
Filter out hidden symbols from labels, added in systems where the
annobin plugin is used, such as RHEL8, which, if left in place make
the DWARF unwind 'perf test' to fail on PPC.
Tony Jones:
Fix 'perf_event_attr' tests when building with python3.
perf mem/c2c:
Ravi Bangoria:
Fix perf_mem_events on PowerPC.
tools headers UAPI:
Arnaldo Carvalho de Melo:
Sync linux/in.h copy from the kernel sources, silencing a perf build warning.
Ursula Braun [Thu, 7 Feb 2019 13:52:54 +0000 (14:52 +0100)]
net/smc: fix byte_order for rx_curs_confirmed
The recent change in the rx_curs_confirmed assignment disregards
byte order, which causes problems on little endian architectures.
This patch fixes it.
Fixes: b8649efad879 ("net/smc: fix sender_free computation") (net-tree) Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Paolo Abeni [Thu, 7 Feb 2019 13:13:18 +0000 (14:13 +0100)]
vsock: cope with memory allocation failure at socket creation time
In the unlikely event that the kmalloc call in vmci_transport_socket_init()
fails, we end-up calling vmci_transport_destruct() with a NULL vmci_trans()
and oopsing.
This change addresses the above explicitly checking for zero vmci_trans()
at destruction time.
net: ipv4: use a dedicated counter for icmp_v4 redirect packets
According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.
Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host
I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4c3f4 ("Linux-2.6.12-rc2")
Linus Torvalds [Sat, 9 Feb 2019 00:23:41 +0000 (16:23 -0800)]
Merge tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a bit larger than normal, as we had not managed to send out a
pull request before traveling for a week without my signing key.
There are multiple code fixes for older bugs, all of which should get
backported into stable kernels:
- tango: one fix for multiplatform configurations broken on other
platforms when tango is enabled
- arm_scmi: device unregistration fix
- iop32x: fix kernel oops from extraneous __init annotation
- pxa: remove a double kfree
- fsl qbman: close an interrupt clearing race
The rest is the usual collection of smaller fixes for device tree
files, on the renesas, allwinner, meson, omap, davinci, qualcomm and
imx platforms.
Some of these are for compile-time warnings, most are for board
specific functionality that fails to work because of incorrect
settings"
* tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: tango: Improve ARCH_MULTIPLATFORM compatibility
firmware: arm_scmi: provide the mandatory device release callback
ARM: iop32x/n2100: fix PCI IRQ mapping
arm64: dts: add msm8996 compatible to gicv3
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: pxa: ssp: unneeded to free devm_ allocated data
ARM: dts: r8a7743: Convert to new LVDS DT bindings
soc: fsl: qbman: avoid race in clearing QMan interrupt
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
ARM: dts: da850: fix interrupt numbers for clocksource
dt-bindings: imx8mq: Number clocks consecutively
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
...
Linus Torvalds [Sat, 9 Feb 2019 00:21:33 +0000 (16:21 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Two arm64 fixes for -rc6. They resolve a kernel NULL dereference in
kexec and bogus kernel page table dumping when userspace is configured
for 52-bit virtual addressing.
Summary:
- Fix kernel oops when attemping kexec_file() with a NULL cmdline
- Fix page table output in debugfs when ARM64_USER_VA_BITS_52=y"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kexec_file: handle empty command-line
arm64: ptdump: Don't iterate kernel page tables using PTRS_PER_PXX
Linus Torvalds [Sat, 9 Feb 2019 00:04:12 +0000 (16:04 -0800)]
Merge tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Just two fixes, both going to stable.
- Our support for split pmd page table lock had a bug which could
lead to a crash on mremap() when using the Radix MMU (Power9 only).
- A fix for the PAPR SCM driver (nvdimm) we added last release, which
had a bug where we might mis-handle a hypervisor response leading
to us failing to attach the memory region.
Thanks to: Aneesh Kumar K.V, Oliver O'Halloran"
* tag 'powerpc-5.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Use the correct bind address
powerpc/radix: Fix kernel crash with mremap()
Linus Torvalds [Fri, 8 Feb 2019 23:39:28 +0000 (15:39 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull signal fixes from Eric Biederman:
"This contains four small fixes for signal handling. A missing range
check, a regression fix, prioritizing signals we have already started
a signal group exit for, and better detection of synchronous signals.
The confused decision of which signals to handle failed spectacularly
when a timer was pointed at SIGBUS and the stack overflowed. Resulting
in an unkillable process in an infinite loop instead of a SIGSEGV and
core dump"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Better detection of synchronous signals
signal: Always notice exiting tasks
signal: Always attempt to allocate siginfo for SIGSTOP
signal: Make siginmask safe when passed a signal of 0
Linus Torvalds [Fri, 8 Feb 2019 23:37:17 +0000 (15:37 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of five minor fixes (although, tecnhincally, the aicxxx
fix is for a major problem in that the driver won't load without it,
but I think the fact it's taken us since 4.10 to discover this
indicates that the user base for these things has declined)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxlflash: Prevent deadlock when adapter probe fails
Revert "scsi: libfc: Add WARN_ON() when deleting rports"
scsi: sd_zbc: Fix zone information messages
scsi: target: make the pi_prot_format ConfigFS path readable
scsi: aic94xx: fix module loading
Linus Torvalds [Fri, 8 Feb 2019 23:34:10 +0000 (15:34 -0800)]
Merge tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"Intel decided to leave the newly added Scalable Mode Feature
default-disabled for now. The patch here accomplishes that"
* tag 'iommu-fixes-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Leave scalable mode default off
Linus Torvalds [Fri, 8 Feb 2019 23:32:10 +0000 (15:32 -0800)]
Merge tag 'pci-v5.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Work around Synopsys duplicate Device ID (HAPS USB3, NXP i.MX) that
breaks PCIe on I.MX SoCs (Thinh Nguyen)"
* tag 'pci-v5.0-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Work around Synopsys duplicate Device ID (HAPS USB3, NXP i.MX)
Linus Torvalds [Fri, 8 Feb 2019 23:30:02 +0000 (15:30 -0800)]
Merge tag 'acpi-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This prevents excessive ACPI debug messages from being printed to the
kernel log, which has started to happen after one of the recent ACPICA
commits (Erik Schmauss)"
* tag 'acpi-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Set debug output flags independent of ACPICA
Russell King [Wed, 6 Feb 2019 10:52:30 +0000 (10:52 +0000)]
net: sfp: do not probe SFP module before we're attached
When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured. However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.
Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.
Pull networking fixes from David Miller:
"This pull request is dedicated to the upcoming snowpocalypse parts 2
and 3 in the Pacific Northwest:
1) Drop profiles are broken because some drivers use dev_kfree_skb*
instead of dev_consume_skb*, from Yang Wei.
2) Fix IWLWIFI kconfig deps, from Luca Coelho.
3) Fix percpu maps updating in bpftool, from Paolo Abeni.
4) Missing station release in batman-adv, from Felix Fietkau.
5) Fix some networking compat ioctl bugs, from Johannes Berg.
6) ucc_geth must reset the BQL queue state when stopping the device,
from Mathias Thore.
7) Several XDP bug fixes in virtio_net from Toshiaki Makita.
8) TSO packets must be sent always on queue 0 in stmmac, from Jose
Abreu.
9) Fix socket refcounting bug in RDS, from Eric Dumazet.
10) Handle sparse cpu allocations in bpf selftests, from Martynas
Pumputis.
11) Make sure mgmt frames have enough tailroom in mac80211, from Felix
Feitkau.
12) Use safe list walking in sctp_sendmsg() asoc list traversal, from
Greg Kroah-Hartman.
13) Make DCCP's ccid_hc_[rt]x_parse_options always check for NULL
ccid, from Eric Dumazet.
14) Need to reload WoL password into bcmsysport device after deep
sleeps, from Florian Fainelli.
15) Remove filter from mask before freeing in cls_flower, from Petr
Machata.
16) Missing release and use after free in error paths of s390 qeth
code, from Julian Wiedmann.
17) Fix lockdep false positive in dsa code, from Marc Zyngier.
18) Fix counting of ATU violations in mv88e6xxx, from Andrew Lunn.
19) Fix EQ firmware assert in qed driver, from Manish Chopra.
20) Don't default Caivum PTP to Y in kconfig, from Bjorn Helgaas"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: dsa: b53: Fix for failure when irq is not defined in dt
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
net: Don't default Cavium PTP driver to 'y'
net: broadcom: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: via-velocity: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tehuti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: sun: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fsl_ucc_hdlc: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fec_mpc52xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: smsc: epic100: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: dscc4: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tulip: de2104x: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: defxx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net/mlx5e: Don't overwrite pedit action when multiple pedit used
net/mlx5e: Update hw flows when encap source mac changed
qed*: Advance drivers version to 8.37.0.20
qed: Change verbosity for coalescing message.
qede: Fix system crash on configuring channels.
qed: Consider TX tcs while deriving the max num_queues for PF.
...
Eric Anholt [Fri, 7 Dec 2018 19:16:53 +0000 (11:16 -0800)]
drm/sched: Always trace the dependencies we wait on, to fix a race.
The entity->dependency can go away completely once we've called
drm_sched_entity_add_dependency_cb() (if the cb is called before we
get around to tracing). The tracepoint is more useful if we trace
every dependency instead of just ones that get callbacks installed,
anyway, so just do that.
Fixes any easy-to-produce OOPS when tracing the scheduler on V3D with
"perf record -a -e gpu_scheduler:.\* glxgears" and DEBUG_SLAB enabled.
Linus Torvalds [Fri, 8 Feb 2019 18:56:31 +0000 (10:56 -0800)]
Merge tag 'char-misc-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char and misc driver fixes for 5.0-rc6.
Nothing huge here, some more binderfs fixups found as people use it,
and there is a "large" selftest added to validate the binderfs code,
which makes up the majority of this pull request.
There's also some small mei and mic fixes to resolve some reported
issues.
All of these have been in linux-next for over a week with no reported
issues"
* tag 'char-misc-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mic: vop: Fix crash on remove
mic: vop: Fix use-after-free on remove
binderfs: remove separate device_initcall()
fpga: stratix10-soc: fix wrong of_node_put() in init function
mic: vop: Fix broken virtqueues
mei: free read cb on ctrl_wr list flush
samples: mei: use /dev/mei0 instead of /dev/mei
mei: me: add ice lake point device id.
binderfs: respect limit on binder control creation
binder: fix CONFIG_ANDROID_BINDER_DEVICES
selftests: add binderfs selftests
Linus Torvalds [Fri, 8 Feb 2019 18:53:44 +0000 (10:53 -0800)]
Merge tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 5.0-rc6.
Well, not so much "driver core" as "debugfs". There's a lot of
outstanding debugfs cleanup patches coming in through different
subsystem trees, and in that process the debugfs core was found that
it really should return errors when something bad happens, to prevent
random files from showing up in the root of debugfs afterward. So
debugfs was fixed up to handle this properly, and then two fixes for
the relay and blk-mq code was needed as it was making invalid
assumptions about debugfs return values.
There's also a cacheinfo fix in here that resolves a tiny issue.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
blk-mq: protect debugfs_create_files() from failures
relay: check return of create_buf_file() properly
debugfs: debugfs_lookup() should return NULL if not found
debugfs: return error values, not NULL
debugfs: fix debugfs_rename parameter checking
cacheinfo: Keep the old value if of_property_read_u32 fails
Linus Torvalds [Fri, 8 Feb 2019 18:49:55 +0000 (10:49 -0800)]
Merge tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial fixes for 5.0-rc6.
Nothing huge, just a few small fixes for reported issues. The speakup
fix is in here as it is a tty operation issue.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: fix race between flush_to_ldisc and tty_open
staging: speakup: fix tty-operation NULL derefs
serial: sh-sci: Do not free irqs that have already been freed
serial: 8250_pci: Make PCI class test non fatal
tty: serial: 8250_mtk: Fix potential NULL pointer dereference
Linus Torvalds [Fri, 8 Feb 2019 18:46:14 +0000 (10:46 -0800)]
Merge tag 'xfs-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are a handful of XFS fixes to fix a data corruption problem, a
crasher bug, and a deadlock.
Summary:
- Fix cache coherency problem with writeback mappings
- Fix buffer deadlock when shutting fs down
- Fix a null pointer dereference when running online repair"
* tag 'xfs-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: set buffer ops when repair probes for btree type
xfs: end sync buffer I/O properly on shutdown error
xfs: eof trim writeback mapping as soon as it is cached
Linus Torvalds [Fri, 8 Feb 2019 18:43:15 +0000 (10:43 -0800)]
Merge tag 'drm-fixes-2019-02-08' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Missed fixes last week as had nothing until amdgpu showed up on
Saturday. Other stuff has since rolled in along with some more amdgpu
fixes, so we have two weeks of those, and some i915, vmwgfx, sun4i,
rockchip and omap fixes.
amdgpu/radeon:
- fix crash on passthrough for SI
- fencing fix for shared buffers
- APU hwmon fix
- API powerplay fix
- eDP freesync fix
- PASID mgr locking fix
- KFD warning fix
- DC/powerplay fix
- raven revision ids fix
- vega20 doorbell fix
* tag 'drm-fixes-2019-02-08' of git://anongit.freedesktop.org/drm/drm: (28 commits)
drm/omap: dsi: Hack-fix DSI bus flags
drm/omap: dsi: Fix OF platform depopulate
drm/omap: dsi: Fix crash in DSI debug dumps
drm/i915: Try to sanitize bogus DPLL state left over by broken SNB BIOSen
drm/amd/display: Attach VRR properties for eDP connectors
drm/amdkfd: Fix if preprocessor statement above kfd_fill_iolink_info_for_cpu
drm/amdgpu: use spin_lock_irqsave to protect vm_manager.pasid_idr
drm/i915: always return something on DDI clock selection
drm/i915: Fix skl srckey mask bits
drm/vmwgfx: Improve on IOMMU detection
drm/vmwgfx: Fix setting of dma masks
drm/vmwgfx: Also check for crtc status while checking for DU active
drm/vmwgfx: Fix an uninitialized fence handle value
drm/vmwgfx: Return error code from vmw_execbuf_copy_fence_user
drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init
drm/amdgpu: fix the incorrect external id for raven series
drm/amdgpu: Implement doorbell self-ring for NBIO 7.4
drm/amd/display: Fix fclk idle state
drm/amdgpu: Transfer fences to dmabuf importer
drm/amd/powerplay: Fix missing break in switch
...
Takashi Iwai [Wed, 6 Feb 2019 06:30:44 +0000 (07:30 +0100)]
ALSA: pcm: Revert capture stream behavior change in blocking mode
In the commit 62ba568f7aef ("ALSA: pcm: Return 0 when size <
start_threshold in capture"), we changed the behavior of
__snd_pcm_lib_xfer() to return immediately with 0 when a capture
stream has a high start_threshold. This was intended to be a
correction of the behavior consistency and looked harmless, but this
was the culprit of the recent breakage reported by syzkaller, which
was fixed by the commit e190161f96b8 ("ALSA: pcm: Fix tight loop of
OSS capture stream").
At the time for the OSS fix, I didn't touch the behavior for ALSA
native API, as assuming that this behavior actually is good. But this
turned out to be also broken actually for a similar deployment,
e.g. one thread goes to a write loop in blocking mode while another
thread controls the start/stop of the stream manually.
Overall, the original commit is harmful, and it brings less merit to
keep that behavior. Let's revert it.
Peter Zijlstra [Fri, 8 Feb 2019 12:08:59 +0000 (13:08 +0100)]
x86/mm/cpa: Fix set_mce_nospec()
The recent commit fe0937b24ff5 ("x86/mm/cpa: Fold cpa_flush_range() and
cpa_flush_array() into a single cpa_flush() function") accidentally made
the call to make_addr_canonical_again() go away, which breaks
set_mce_nospec().
Re-instate the call to convert the address back into canonical form right
before invoking either CLFLUSH or INVLPG. Rename the function while at it
to be shorter (and less MAGA).
Takashi Iwai [Fri, 8 Feb 2019 13:07:18 +0000 (14:07 +0100)]
Merge tag 'asoc-fix-v5.0-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.0
A selection of driver specific fixes here, along with a few core fixes:
- A fixup for some MFD devices that were broken by the previous fixes
for deferred probe.
- A fix for potential out of bounds array accesses when ordering DAPM
power/up down sequences.
- Avoid use after free issue when unloading and reloading drivers using
topologies.
Thomas Gleixner [Tue, 29 Jan 2019 22:15:12 +0000 (23:15 +0100)]
futex: Handle early deadlock return correctly
commit 56222b212e8e ("futex: Drop hb->lock before enqueueing on the
rtmutex") changed the locking rules in the futex code so that the hash
bucket lock is not longer held while the waiter is enqueued into the
rtmutex wait list. This made the lock and the unlock path symmetric, but
unfortunately the possible early exit from __rt_mutex_proxy_start() due to
a detected deadlock was not updated accordingly. That allows a concurrent
unlocker to observe inconsitent state which triggers the warning in the
unlock path.
The problem is caused by the remove(rtmutex_waiter) in the failure case of
__rt_mutex_proxy_start() as this lets the unlocker observe a waiter in the
hash bucket but no waiter on the rtmutex, i.e. inconsistent state.
The original commit handles this correctly for the other early return cases
(timeout, signal) by delaying the removal of the rtmutex waiter until the
returning task reacquired the hash bucket lock.
Treat the failure case of __rt_mutex_proxy_start() in the same way and let
the existing cleanup code handle the eventual handover of the rtmutex
gracefully. The regular rt_mutex_proxy_start() gains the rtmutex waiter
removal for the failure case, so that the other callsites are still
operating correctly.
Add proper comments to the code so all these details are fully documented.
Thanks to Peter for helping with the analysis and writing the really
valuable code comments.
Davidlohr Bueso [Wed, 6 Feb 2019 18:56:02 +0000 (10:56 -0800)]
futex: Fix barrier comment
The current comment for the barrier that guarantees that waiter increment
is always before taking the hb spinlock (barrier (A)) needs to be fixed as
it is misplaced.
This is obviously referring to hb_waiters_inc, which is a full barrier.
Zachary Hays [Thu, 7 Feb 2019 15:03:08 +0000 (10:03 -0500)]
mmc: block: handle complete_work on separate workqueue
The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set.
This generates a rescuer thread for that queue that will trigger when
the CPU is under heavy load and collect the uncompleted work.
In the case of mmc, this creates the possibility of a deadlock when
there are multiple partitions on the device as other blk-mq work is
also run on the same queue. For example:
- worker 0 claims the mmc host to work on partition 1
- worker 1 attempts to claim the host for partition 2 but has to wait
for worker 0 to finish
- worker 0 schedules complete_work to release the host
- rescuer thread is triggered after time-out and collects the dangling
work
- rescuer thread attempts to complete the work in order starting with
claim host
- the task to release host is now blocked by a task to claim it and
will never be called
The above results in multiple hung tasks that lead to failures to
mount partitions.
Handling complete_work on a separate workqueue avoids this by keeping
the work completion tasks separate from the other blk-mq work. This
allows the host to be released without getting blocked by other tasks
attempting to claim the host.
We were enabling autosuspend, which is using data set by the
hash module, prior to the hash module being inited, casuing
a crash on resume as part of the startup sequence if the race
was lost.
This was never a real problem because the PM infra was using low
res timers so we were always winning the race, until commit 8234f6734c5d
("PM-runtime: Switch autosuspend over to using hrtimers") changed that :-)
Fix this by seperating the PM setup and enablement and doing the
latter only at the end of the init sequence.
net: dsa: b53: Fix for failure when irq is not defined in dt
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6fc ("net: dsa: b53: Make SRAB driver manage port interrupts") Fixes: b2ddc48a81b5 ("net: dsa: b53: Do not fail when IRQ are not initialized") Signed-off-by: Arun Parameswaran <[email protected]> Reviewed-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dave Airlie [Fri, 8 Feb 2019 00:32:47 +0000 (10:32 +1000)]
Merge tag 'drm-misc-fixes-2019-02-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.0-rc6:
- Fixes to omap/dsi encoder.
- Clock fix for sun4i.
- Licensing header fix for rockchip.
- Fix division by zero in the mode when trying to set a mode on
i915 with GVT-g enabled.
Linus Torvalds [Thu, 7 Feb 2019 22:53:26 +0000 (15:53 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Three security fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
Linus Torvalds [Thu, 7 Feb 2019 22:44:45 +0000 (15:44 -0700)]
Merge tag 'nfsd-5.0-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Two small nfsd bugfixes for 5.0, for an RDMA bug and a file clone bug"
* tag 'nfsd-5.0-1' of git://linux-nfs.org/~bfields/linux:
svcrdma: Remove max_sge check at connect time
nfsd: Fix error return values for nfsd4_clone_file_range()
projects / linux.git / log