Alan Stern [Wed, 26 Aug 2020 19:46:24 +0000 (15:46 -0400)]
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Dan Carpenter [Wed, 26 Aug 2020 11:33:30 +0000 (14:33 +0300)]
dma-pool: Fix an uninitialized variable bug in atomic_pool_expand()
The "page" pointer can be used with out being initialized.
Fixes: d7e673ec2c8e ("dma-pool: Only allocate from CMA when in same memory zone") Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
Simon Leiner [Tue, 25 Aug 2020 09:31:53 +0000 (11:31 +0200)]
arm/xen: Add misuse warning to virt_to_gfn
As virt_to_gfn uses virt_to_phys, it will return invalid addresses when
used with vmalloc'd addresses. This patch introduces a warning, when
virt_to_gfn is used in this way.
Simon Leiner [Tue, 25 Aug 2020 09:31:52 +0000 (11:31 +0200)]
xen/xenbus: Fix granting of vmalloc'd memory
On some architectures (like ARM), virt_to_gfn cannot be used for
vmalloc'd memory because of its reliance on virt_to_phys. This patch
introduces a check for vmalloc'd addresses and obtains the PFN using
vmalloc_to_pfn in that case.
Thomas Gleixner [Tue, 25 Aug 2020 15:22:58 +0000 (17:22 +0200)]
XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt
XEN data pointer which contains XEN specific information.
handler data is meant for interrupt handlers and not for storing irq chip
specific information as some devices require handler data to store internal
per interrupt information, e.g. pinctrl/GPIO chained interrupt handlers.
This obviously creates a conflict of interests and crashes the machine
because the XEN pointer is overwritten by the driver pointer.
As the XEN data is not handler specific it should be stored in
irqdesc::irq_data::chip_data instead.
A simple sed s/irq_[sg]et_handler_data/irq_[sg]et_chip_data/ cures that.
Dave Airlie [Thu, 27 Aug 2020 02:44:04 +0000 (12:44 +1000)]
Merge tag 'amd-drm-fixes-5.9-2020-08-26' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.9-2020-08-26:
amdgpu:
- Misc display fixes
- Backlight fixes
- MPO fix for DCN1
- Fixes for Sienna Cichlid
- Fixes for Navy Flounder
- Vega SW CTF fixes
- SMU fix for Raven
- Fix a possible overflow in INFO ioctl
- Gfx10 clockgating fix
Dave Airlie [Thu, 27 Aug 2020 02:36:32 +0000 (12:36 +1000)]
Merge tag 'drm-msm-fixes-2020-08-24' of https://gitlab.freedesktop.org/drm/msm into drm-fixes
Some fixes for v5.9 plus the one opp/bandwidth scaling patch ("drm:
msm: a6xx: use dev_pm_opp_set_bw to scale DDR") which was not included
in the initial pull due to dependency on patch landing thru OPP tree
Dave Airlie [Thu, 27 Aug 2020 02:34:06 +0000 (12:34 +1000)]
Merge branch 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux into drm-fixes
Two fixes:
One fixes a bad interaction with the DRM scheduler, leading to some dma
fences not getting signalled after hitting the job timeout. The other
one fixes a GPU init regression, as apparently one old core doesn't
likes us reading some of the identification registers.
Jens Axboe [Thu, 27 Aug 2020 00:58:26 +0000 (18:58 -0600)]
io_uring: clear req->result on IOPOLL re-issue
Make sure we clear req->result, which was set to -EAGAIN for retry
purposes, when moving it to the reissue list. Otherwise we can end up
retrying a request more than once, which leads to weird results in
the io-wq handling (and other spots).
Dinghao Liu [Wed, 26 Aug 2020 13:24:58 +0000 (21:24 +0800)]
drm/amd/display: Fix memleak in amdgpu_dm_mode_config_init
When amdgpu_display_modeset_create_props() fails, state and
state->context should be freed to prevent memleak. It's the
same when amdgpu_dm_audio_init() fails.
Wayne Lin [Tue, 18 Aug 2020 03:19:42 +0000 (11:19 +0800)]
drm/amd/display: Retry AUX write when fail occurs
[Why]
In dm_dp_aux_transfer() now, we forget to handle AUX_WR fail cases. We
suppose every write wil get done successfully and hence some AUX
commands might not sent out indeed.
Alex Deucher [Tue, 25 Aug 2020 15:43:45 +0000 (11:43 -0400)]
drm/amdgpu: Fix buffer overflow in INFO ioctl
The values for "se_num" and "sh_num" come from the user in the ioctl.
They can be in the 0-255 range but if they're more than
AMDGPU_GFX_MAX_SE (4) or AMDGPU_GFX_MAX_SH_PER_SE (2) then it results in
an out of bounds read.
drm/amd/powerplay: Fix hardmins not being sent to SMU for RV
[Why]
DC uses these to raise the voltage as needed for higher dispclk/dppclk
and to ensure that we have enough bandwidth to drive the displays.
There's a bug preventing these from actuially sending messages since
it's checking the actual clock (which is 0) instead of the incoming
clock (which shouldn't be 0) when deciding to send the hardmin.
[How]
Check the clocks != 0 instead of the actual clocks.
Samson Tam [Thu, 13 Aug 2020 14:50:21 +0000 (10:50 -0400)]
drm/amd/display: Fix passive dongle mistaken as active dongle in EDID emulation
[Why]
dongle_type is set during dongle connection but for passive dongles,
dongle_type is not set. If user starts with an active dongle and
then switches to a passive dongle, it will still report as an active
dongle. Trying to emulate the wrong connecter type results in display
not lighting up.
[How]
Set dpcd_caps.dongle_type for passive dongles in detect_dp().
[Why]
Revert HDCP disable sequence change that blanks stream before
disabling HDCP. PSP and HW teams are currently investigating the
root cause of why HDCP cannot be disabled before stream blank,
which is expected to work without issues.
Furquan Shaikh [Thu, 20 Aug 2020 07:52:41 +0000 (00:52 -0700)]
drivers: gpu: amd: Initialize amdgpu_dm_backlight_caps object to 0 in amdgpu_dm_update_backlight_caps
In `amdgpu_dm_update_backlight_caps()`, there is a local
`amdgpu_dm_backlight_caps` object that is filled in by
`amdgpu_acpi_get_backlight_caps()`. However, this object is
uninitialized before the call and hence the subsequent check for
aux_support can fail since it is not initialized by
`amdgpu_acpi_get_backlight_caps()` as well. This change initializes
this local `amdgpu_dm_backlight_caps` object to 0.
drm/amd/display: Reject overlay plane configurations in multi-display scenarios
[Why]
These aren't stable on some platform configurations when driving
multiple displays, especially on higher resolution.
In particular the delay in asserting p-state and validating from
x86 outweights any power or performance benefit from the hardware
composition.
Under some configurations this will manifest itself as extreme stutter
or unresponsiveness especially when combined with cursor movement.
[How]
Disable these for now. Exposing overlays to userspace doesn't guarantee
that they'll be able to use them in any and all configurations and it's
part of the DRM contract to have userspace gracefully handle validation
failures when they occur.
Valdiation occurs as part of DC and this in particular affects RV, so
disable this in dcn10_global_validation.
drm/amd/display: use correct scale for actual_brightness
Documentation for sysfs backlight level interface requires that
values in both 'brightness' and 'actual_brightness' files are
interpreted to be in range from 0 to the value given in the
'max_brightness' file.
With amdgpu, max_brightness gives 255, and values written by the user
into 'brightness' are internally rescaled to a wider range. However,
reading from 'actual_brightness' gives the raw register value without
inverse rescaling. This causes issues for various userspace tools such
as PowerTop and systemd that expect the value to be in the correct
range.
Introduce a helper to retrieve internal backlight range. Use it to
reimplement 'convert_brightness' as 'convert_brightness_from_user' and
introduce 'convert_brightness_to_user'.
Linus Torvalds [Wed, 26 Aug 2020 17:58:20 +0000 (10:58 -0700)]
Merge tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: add dependence and build for earlycon
serial: samsung: Removes the IRQ not found warning
serial: 8250: change lock order in serial8250_do_startup()
serial: stm32: avoid kernel warning on absence of optional IRQ
serial: pl011: Fix oops on -EPROBE_DEFER
serial: pl011: Don't leak amba_ports entry on driver register error
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup
serial: qcom_geni_serial: Fix recent kdb hang
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
fbcon: prevent user font height or width change from causing potential out-of-bounds access
vt: defer kfree() of vc_screenbuf in vc_do_resize()
Linus Torvalds [Wed, 26 Aug 2020 17:50:50 +0000 (10:50 -0700)]
Merge tag 'char-misc-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc and other driver subsystem fixes for
5.9-rc3.
The majority of these are tiny habanalabs driver fixes, but also in
here are:
- speakup build fixes now that it is out of staging and got exposed
to more build systems all of a sudden
- mei driver fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
habanalabs: correctly report inbound pci region cfg error
habanalabs: check correct vmalloc return code
habanalabs: validate FW file size
habanalabs: fix incorrect check on failed workqueue create
habanalabs: set max power according to card type
habanalabs: proper handling of alloc size in coresight
habanalabs: set clock gating according to mask
habanalabs: verify user input in cs_ioctl_signal_wait
habanalabs: Fix a loop in gaudi_extract_ecc_info()
habanalabs: Fix memory corruption in debugfs
habanalabs: validate packet id during CB parse
habanalabs: Validate user address before mapping
habanalabs: unmap PCI bars upon iATU failure
mei: hdcp: fix mei_hdcp_verify_mprime() input parameter
speakup: only build serialio when ISA is enabled
speakup: Fix wait_for_xmitr for ttyio case
Linus Torvalds [Wed, 26 Aug 2020 17:44:15 +0000 (10:44 -0700)]
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
"Two patches from Vineeth to improve Hyper-V timesync facility"
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv_utils: drain the timesync packets on onchannelcallback
hv_utils: return error if host timesysnc update is stale
Linus Torvalds [Wed, 26 Aug 2020 17:40:09 +0000 (10:40 -0700)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bugfixes from Michael Tsirkin:
"A couple vdpa and vhost bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vdpa/mlx5: Avoid warnings about shifts on 32-bit platforms
vhost-iotlb: fix vhost_iotlb_itree_next() documentation
vdpa: ifcvf: free config irq in ifcvf_free_irq()
vdpa: ifcvf: return err when fail to request config irq
Jens Axboe [Wed, 26 Aug 2020 16:36:20 +0000 (10:36 -0600)]
io_uring: make offset == -1 consistent with preadv2/pwritev2
The man page for io_uring generally claims were consistent with what
preadv2 and pwritev2 accept, but turns out there's a slight discrepancy
in how offset == -1 is handled for pipes/streams. preadv doesn't allow
it, but preadv2 does. This currently causes io_uring to return -EINVAL
if that is attempted, but we should allow that as documented.
This change makes us consistent with preadv2/pwritev2 for just passing
in a NULL ppos for streams if the offset is -1.
Sven Schnelle [Thu, 20 Aug 2020 07:48:23 +0000 (09:48 +0200)]
s390: don't trace preemption in percpu macros
Since commit a21ee6055c30 ("lockdep: Change hardirq{s_enabled,_context}
to per-cpu variables") the lockdep code itself uses percpu variables. This
leads to recursions because the percpu macros are calling preempt_enable()
which might call trace_preempt_on().
Martijn Coenen [Tue, 25 Aug 2020 07:18:29 +0000 (09:18 +0200)]
loop: Set correct device size when using LOOP_CONFIGURE
The device size calculation was done before processing the loop
configuration, which meant that the we set the size on the underlying
block device incorrectly in case lo_offset/lo_sizelimit were set in the
configuration. Delay computing the size until we've setup the device
parameters correctly.
Hou Pu [Mon, 10 Aug 2020 12:00:44 +0000 (08:00 -0400)]
nbd: restore default timeout when setting it to zero
If we configured io timeout of nbd0 to 100s. Later after we
finished using it, we configured nbd0 again and set the io
timeout to 0. We expect it would timeout after 30 seconds
and keep retry. But in fact we could not change the timeout
when we set it to 0. the timeout is still the original 100s.
So change the timeout to default 30s when we set it to zero.
It also behaves same as commit 2da22da57348 ("nbd: fix zero
cmd timeout handling v2").
It becomes more important if we were reconfigure a nbd device
and the io timeout it set to zero. Because it could take 30s
to detect the new socket and thus io could be completed more
quickly compared to 100s.
vdpa/mlx5: Avoid warnings about shifts on 32-bit platforms
Clang warns several times when building for 32-bit ARM along the lines
of:
drivers/vdpa/mlx5/net/mlx5_vnet.c:1462:31: warning: shift count >= width
of type [-Wshift-count-overflow]
ndev->mvdev.mlx_features |= BIT(VIRTIO_F_VERSION_1);
^~~~~~~~~~~~~~~~~~~~~~~
This is related to the BIT macro, which uses an unsigned long literal,
which is 32-bit on ARM so having a shift equal to or larger than 32 will
cause this warning, such as the above, where VIRTIO_F_VERSION_1 is 32.
To avoid this, use BIT_ULL, which will be an unsigned long long. This
matches the size of the features field throughout this driver, which is
u64 so there should be no functional change.
This patch contains trivial changes for the vhost_iotlb_itree_next()
documentation, fixing the function name and the description of
first argument (@map).
Jason Wang [Thu, 23 Jul 2020 09:12:54 +0000 (17:12 +0800)]
vdpa: ifcvf: free config irq in ifcvf_free_irq()
We don't free config irq in ifcvf_free_irq() which will trigger a
BUG() in pci core since we try to free the vectors that has an
action. Fixing this by recording the config irq in ifcvf_hw structure
and free it in ifcvf_free_irq().
Peter Zijlstra [Fri, 7 Aug 2020 18:53:16 +0000 (20:53 +0200)]
lockdep,trace: Expose tracepoints
The lockdep tracepoints are under the lockdep recursion counter, this
has a bunch of nasty side effects:
- TRACE_IRQFLAGS doesn't work across the entire tracepoint
- RCU-lockdep doesn't see the tracepoints either, hiding numerous
"suspicious RCU usage" warnings.
Pull the trace_lock_*() tracepoints completely out from under the
lockdep recursion handling and completely rely on the trace level
recusion handling -- also, tracing *SHOULD* not be taking locks in any
case.
Nicholas Piggin [Thu, 23 Jul 2020 10:56:14 +0000 (20:56 +1000)]
lockdep: Only trace IRQ edges
Problem:
raw_local_irq_save(); // software state on
local_irq_save(); // software state off
...
local_irq_restore(); // software state still off, because we don't enable IRQs
raw_local_irq_restore(); // software state still off, *whoopsie*
existing instances:
- lock_acquire()
raw_local_irq_save()
__lock_acquire()
arch_spin_lock(&graph_lock)
pv_wait() := kvm_wait() (same or worse for Xen/HyperV)
local_irq_save()
A) make it work by enabling the tracing inside raw_*()
B) make it work by keeping tracing disabled inside raw_*()
C) call it broken and clean it up now
Now, given that the only reason to use the raw_* variant is because you don't
want tracing. Therefore A) seems like a weird option (although it can be done).
C) is tempting, but OTOH it ends up converting a _lot_ of code to raw just
because there is one raw user, this strips the validation/tracing off for all
the other users.
So we pick B) and declare any code that ends up doing:
broken. AFAICT this problem has existed forever, the only reason it came
up is because commit: 859d069ee1dd ("lockdep: Prepare for NMI IRQ
state tracking") changed IRQ tracing vs lockdep recursion and the
first instance is fairly common, the other cases hardly ever happen.
Peter Zijlstra [Wed, 12 Aug 2020 10:27:10 +0000 (12:27 +0200)]
cpuidle: Move trace_cpu_idle() into generic code
Remove trace_cpu_idle() from the arch_cpu_idle() implementations and
put it in the generic code, right before disabling RCU. Gets rid of
more trace_*_rcuidle() users.
Peter Zijlstra [Thu, 20 Aug 2020 07:13:30 +0000 (09:13 +0200)]
lockdep: Use raw_cpu_*() for per-cpu variables
Sven reported that commit a21ee6055c30 ("lockdep: Change
hardirq{s_enabled,_context} to per-cpu variables") caused trouble on
s390 because their this_cpu_*() primitives disable preemption which
then lands back tracing.
On the one hand, per-cpu ops should use preempt_*able_notrace() and
raw_local_irq_*(), on the other hand, we can trivialy use raw_cpu_*()
ops for this.
Marco Elver [Thu, 20 Aug 2020 17:20:46 +0000 (19:20 +0200)]
sched: Use __always_inline on is_idle_task()
is_idle_task() may be used from noinstr functions such as
irqentry_enter(). Since the compiler is free to not inline regular
inline functions, switch to using __always_inline.
Marek Szyprowski [Mon, 13 Jul 2020 07:07:08 +0000 (09:07 +0200)]
drm/exynos: gem: Fix sparse warning
kvaddr element of the exynos_gem object points to a memory buffer, thus
it should not have a __iomem annotation. Then, to avoid a warning or
casting on assignment to fbi structure, the screen_buffer element of the
union should be used instead of the screen_base.
Thomas Gleixner [Tue, 25 Aug 2020 23:36:07 +0000 (01:36 +0200)]
Merge tag 'irqchip-fixes-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Revert the wholesale conversion to platform drivers of the pdc, sysirq
and cirq drivers, as it breaks a number of platforms even when the
driver is built-in (probe ordering bites you).
- Prevent interrupt from being lost with the STM32 exti driver
- Fix wake-up interrupts for the MIPS Ingenic driver
- Fix an embarassing typo in the new module helpers, leading to the probe
failing most of the time
- The promised TI firmware rework that couldn't make it into the merge
window due to a very badly managed set of dependencies
Linus Torvalds [Tue, 25 Aug 2020 18:59:23 +0000 (11:59 -0700)]
Merge tag 'm68knommu-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu fix from Greg Ungerer:
"Only a single fix for the binfmt_flat loader (reverting a recent
change)"
* tag 'm68knommu-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
binfmt_flat: revert "binfmt_flat: don't offset the data start"
Jens Axboe [Tue, 25 Aug 2020 18:59:22 +0000 (12:59 -0600)]
io_uring: ensure read requests go through -ERESTART* transformation
We need to call kiocb_done() for any ret < 0 to ensure that we always
get the proper -ERESTARTSYS (and friends) transformation done.
At some point this should be tied into general error handling, so we
can get rid of the various (mostly network) related commands that check
and perform this substitution.
Linus Torvalds [Tue, 25 Aug 2020 18:42:43 +0000 (11:42 -0700)]
Merge tag 'libnvdimm-fix-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Vishal Verma:
"A couple of minor fixes for things merged in 5.9-rc1.
One is an out-of-bounds access caught by KASAN, and the second is a
tweak to some overzealous logging about dax support even for
traditional block devices which was unnecessary"
* tag 'libnvdimm-fix-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: do not print error message for non-persistent memory block device
libnvdimm: KASAN: global-out-of-bounds Read in internal_create_group
Jens Axboe [Tue, 25 Aug 2020 18:27:50 +0000 (12:27 -0600)]
io_uring: don't use poll handler if file can't be nonblocking read/written
There's no point in using the poll handler if we can't do a nonblocking
IO attempt of the operation, since we'll need to go async anyway. In
fact this is actively harmful, as reading from eg pipes won't return 0
to indicate EOF.
Linus Torvalds [Tue, 25 Aug 2020 18:13:29 +0000 (11:13 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- regression fix / revert of a commit that intended to reduce probing
delay by ~50ms, but introduced a race that causes quite a few devices
not to enumerate, or get stuck on first IRQ
- buffer overflow fix in hiddev, from Peilin Ye
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
Revert "HID: usbhid: do not sleep when opening device"
HID: hiddev: Fix slab-out-of-bounds write in hiddev_ioctl_usage()
HID: quirks: Always poll three more Lenovo PixArt mice
HID: i2c-hid: Always sleep 60ms after I2C_HID_PWR_ON commands
HID: macally: Constify macally_id_table
HID: cougar: Constify cougar_id_table
Jens Axboe [Tue, 25 Aug 2020 13:58:00 +0000 (07:58 -0600)]
io_uring: fix imbalanced sqo_mm accounting
We do the initial accounting of locked_vm and pinned_vm before we have
setup ctx->sqo_mm, which means we can end up having not accounted the
memory at setup time, but still decrement it when we exit. This causes
an imbalance in the accounting.
Setup ctx->sqo_mm earlier in io_uring_create(), before we do the first
accounting of mm->{locked,pinned}_vm. This also unifies the state
grabbing for the ctx, and eliminates a failure case in
io_sq_offload_start().
PM: sleep: core: Fix the handling of pending runtime resume requests
It has been reported that system-wide suspend may be aborted in the
absence of any wakeup events due to unforseen interactions of it with
the runtume PM framework.
One failing scenario is when there are multiple devices sharing an
ACPI power resource and runtime-resume needs to be carried out for
one of them during system-wide suspend (for example, because it needs
to be reconfigured before the whole system goes to sleep). In that
case, the runtime-resume of that device involves turning the ACPI
power resource "on" which in turn causes runtime-resume requests
to be queued up for all of the other devices sharing it. Those
requests go to the runtime PM workqueue which is frozen during
system-wide suspend, so they are not actually taken care of until
the resume of the whole system, but the pm_runtime_barrier()
call in __device_suspend() sees them and triggers system wakeup
events for them which then cause the system-wide suspend to be
aborted if wakeup source objects are in active use.
Of course, the logic that leads to triggering those wakeup events is
questionable in the first place, because clearly there are cases in
which a pending runtime resume request for a device is not connected
to any real wakeup events in any way (like the one above). Moreover,
it is racy, because the device may be resuming already by the time
the pm_runtime_barrier() runs and so if the driver doesn't take care
of signaling the wakeup event as appropriate, it will be lost.
However, if the driver does take care of that, the extra
pm_wakeup_event() call in the core is redundant.
Accordingly, drop the conditional pm_wakeup_event() call fron
__device_suspend() and make the latter call pm_runtime_barrier()
alone. Also modify the comment next to that call to reflect the new
code and extend it to mention the need to avoid unwanted interactions
between runtime PM and system-wide device suspend callbacks.
ACPI: OSL: Prevent acpi_release_memory() from returning too early
After commit 1757659d022b ("ACPI: OSL: Implement deferred unmapping
of ACPI memory") in some cases acpi_release_memory() may return
before the target memory mappings actually go away, because they
are released asynchronously now.
Prevent it from returning prematurely by making it wait for the next
RCU grace period to elapse, for all of the RCU callbacks to complete
and for all of the scheduled work items to be flushed before
returning.
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
The patch addresses the compliance test failures while running TDA
2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered, while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.
TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.
UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].
This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."
With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.
Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS", the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e. tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.
The commit 2a6c0b82e651 ("USB: PHY: JZ4770: Add support for new
Ingenic SoCs.") introduced the initialization function for different
chips, but left the relevant code involved in the resetting process
in the original function, resulting in uninitialized variable calls.
Brooke Basile [Tue, 25 Aug 2020 13:07:27 +0000 (09:07 -0400)]
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Brooke Basile [Tue, 25 Aug 2020 13:05:08 +0000 (09:05 -0400)]
USB: gadget: u_f: add overflow checks to VLA macros
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
Jens Axboe [Mon, 24 Aug 2020 17:45:26 +0000 (11:45 -0600)]
io_uring: revert consumed iov_iter bytes on error
Some consumers of the iov_iter will return an error, but still have
bytes consumed in the iterator. This is an issue for -EAGAIN, since we
rely on a sane iov_iter state across retries.
Fix this by ensuring that we revert consumed bytes, if any, if the file
operations have consumed any bytes from iterator. This is similar to what
generic_file_read_iter() does, and is always safe as we have the previous
bytes count handy already.
Paul Cercueil [Wed, 19 Aug 2020 18:06:02 +0000 (20:06 +0200)]
irqchip/ingenic: Leave parent IRQ unmasked on suspend
All the wakeup sources we possibly want will go through the interrupt
controller, so the parent IRQ must not be masked during suspend, or
there won't be any way to wake up the system.
qiuguorui1 [Thu, 20 Aug 2020 03:16:29 +0000 (11:16 +0800)]
irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Marc Zyngier [Tue, 25 Aug 2020 09:38:39 +0000 (10:38 +0100)]
irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
It has become obvious that switching a number of irqchip drivers
to being platform drivers without considering the platform was a
mistake. We have multiple reports of end-point drivers not
probing because the irqchip driver isn't there yet, breaking
the expectations of the users.
This patch reverts:
920ecb8c35cb ("irqchip/mtk-cirq: Convert to a platform driver") f97dbf48ca43 ("irqchip/mtk-sysirq: Convert to a platform driver") 5be57099d445 ("irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros") 95bf9305d2e3 ("irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module")
and leave QCOM PDC, MTK sysrq and cirq drivers as built-in, special purpose
drivers for the time being until we have worked out a better solution.
The reason for this is that omapdrm calls drm_crtc_vblank_on() while
holding event_lock taken with spin_lock_irq().
It is not clear why drm_crtc_vblank_on() and drm_crtc_vblank_get() are
called while holding event_lock. I don't see any problem with moving
those calls outside the lock, which is what this patch does.
Wolfram Sang [Mon, 17 Aug 2020 12:19:30 +0000 (14:19 +0200)]
i2c: rcar: in slave mode, clear NACK earlier
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
Andy Shevchenko [Fri, 21 Aug 2020 17:03:33 +0000 (20:03 +0300)]
i2c: core: Don't fail PRP0001 enumeration when no ID table exist
When commit c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case
as well") fixed the enumeration of I²C devices on ACPI enabled platforms
when driver has no ID table, it missed the PRP0001 support.
i2c_device_match() and i2c_acpi_match_device() differently match
driver against given device. Use acpi_driver_match_device(), that is used
in the former, in i2c_device_probe() and don't fail PRP0001 enumeration
when no ID table exist.
$ make -skj"$(nproc)" ARCH=powerpc CROSS_COMPILE=powerpc64le-linux- distclean powernv_defconfig zImage
...
In file included from arch/powerpc/boot/../../../lib/decompress_unxz.c:234,
from arch/powerpc/boot/decompress.c:38:
arch/powerpc/boot/../../../lib/xz/xz_dec_stream.c: In function 'dec_main':
arch/powerpc/boot/../../../lib/xz/xz_dec_stream.c:586:4: error: 'fallthrough' undeclared (first use in this function)
586 | fallthrough;
| ^~~~~~~~~~~
This will end up affecting distribution configurations such as Debian
and OpenSUSE according to my testing. I am not sure what the solution
is, the PowerPC wrapper does not set -D__KERNEL__ so I am not sure
that compiler_attributes.h can be safely included."
In order to avoid these sort of problems, it seems that the best
solution is to use /* fall through */ comments instead of the
fallthrough pseudo-keyword macro in lib/, for now.
Reported-by: Nathan Chancellor <[email protected]> Fixes: df561f6688fe ("treewide: Use fallthrough pseudo-keyword") Signed-off-by: Gustavo A. R. Silva <[email protected]> Reviewed-and-tested-by: Nathan Chancellor <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
Linus Torvalds [Mon, 24 Aug 2020 19:01:20 +0000 (12:01 -0700)]
Merge tag 'for-5.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix swapfile activation on subvolumes with deleted snapshots
- error value mixup when removing directory entries from tree log
- fix lzo compression level reset after previous level setting
- fix space cache memory leak after transaction abort
- fix const function attribute
- more error handling improvements
* tag 'for-5.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: detect nocow for swap after snapshot delete
btrfs: check the right error variable in btrfs_del_dir_entries_in_log
btrfs: fix space cache memory leak after transaction abort
btrfs: use the correct const function attribute for btrfs_get_num_csums
btrfs: reset compression level for lzo on remount
btrfs: handle errors from async submission
Linus Torvalds [Mon, 24 Aug 2020 18:53:15 +0000 (11:53 -0700)]
Merge tag 'io_uring-5.9-2020-08-23' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Sagi:
- nvme completion rework from Christoph and Chao that mostly came
from a bit of divergence of how we classify errors related to
pathing/retry etc.
- nvmet passthru fixes from Chaitanya
- minor nvmet fixes from Amit and I
- mpath round-robin path selection fix from Martin
- ignore noiob for zoned devices from Keith
- minor nvme-fc fix from Tianjia"
- BFQ cgroup leak fix (Dmitry)
- block layer MAINTAINERS addition (Geert)
- fix null_blk FUA checking (Hou)
- get_max_io_size() size fix (Keith)
- fix block page_is_mergeable() for compound pages (Matthew)
- discard granularity fixes (Ming)
- IO scheduler ordering fix (Ming)
- misc fixes
* tag 'io_uring-5.9-2020-08-23' of git://git.kernel.dk/linux-block: (31 commits)
null_blk: fix passing of REQ_FUA flag in null_handle_rq
nvmet: Disable keep-alive timer when kato is cleared to 0h
nvme: redirect commands on dying queue
nvme: just check the status code type in nvme_is_path_error
nvme: refactor command completion
nvme: rename and document nvme_end_request
nvme: skip noiob for zoned devices
nvme-pci: fix PRP pool size
nvme-pci: Use u32 for nvme_dev.q_depth and nvme_queue.q_depth
nvme: Use spin_lock_irq() when taking the ctrl->lock
nvmet: call blk_mq_free_request() directly
nvmet: fix oops in pt cmd execution
nvmet: add ns tear down label for pt-cmd handling
nvme: multipath: round-robin: eliminate "fallback" variable
nvme: multipath: round-robin: fix single non-optimized path case
nvme-fc: Fix wrong return value in __nvme_fc_init_request()
nvmet-passthru: Reject commands with non-sgl flags set
nvmet: fix a memory leak
blkcg: fix memleak for iolatency
MAINTAINERS: Add missing header files to BLOCK LAYER section
...
Linus Torvalds [Mon, 24 Aug 2020 18:30:52 +0000 (11:30 -0700)]
Merge tag 'fallthrough-pseudo-keyword-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull 'fallthrough' keyword conversion from Gustavo A. R. Silva:
"A tree-wide patch that replaces tons (2484) of /* fall through */
comments, and its variants, with the new pseudo-keyword macro
fallthrough[1]. Also, remove unnecessary fall-through markings when it
is the case.
There are currently 1167 intances of this fallthrough pseudo-keyword
macro in mainline (5.9-rc2), that have been introduced over the last
couple of development cycles:
$ git grep -nw 'fallthrough;' | wc -l
1167
The global adoption of the fallthrough pseudo-keyword is something
certain to happen; so, better sooner than later. :) This will also
save everybody's time and thousands of lines of unnecessarily
repetitive changelog text.
After applying this patch on top of 5.9-rc2, we'll have a total of
3651 instances of this macro:
$ git grep -nw 'fallthrough;' | wc -l
3651
This treewide patch doesn't address ALL fall-through markings in all
subsystems at once because I have previously sent out patches for some
of such subsystems separately, and I will follow up on them; however,
this definitely contributes most of the work needed to replace all the
fall-through markings with the fallthrough pseudo-keyword macro in the
whole codebase.
I have build-tested this patch on 10 different architectures: x86_64,
i386, arm64, powerpc, s390, sparc64, sh, m68k, powerpc64 and alpha
(allyesconfig for all of them). This is in linux-next already and
kernel test robot has also helped me to successfully build-test early
versions of this patch[2][3][4][5]"
Jeff Layton [Thu, 20 Aug 2020 15:00:26 +0000 (11:00 -0400)]
ceph: don't allow setlease on cephfs
Leases don't currently work correctly on kcephfs, as they are not broken
when caps are revoked. They could eventually be implemented similarly to
how we did them in libcephfs, but for now don't allow them.
[ idryomov: no need for simple_nosetlease() in ceph_dir_fops and
ceph_snapdir_fops ]
Jeff Layton [Tue, 18 Aug 2020 12:03:48 +0000 (08:03 -0400)]
ceph: fix inode number handling on arches with 32-bit ino_t
Tuan and Ulrich mentioned that they were hitting a problem on s390x,
which has a 32-bit ino_t value, even though it's a 64-bit arch (for
historical reasons).
I think the current handling of inode numbers in the ceph driver is
wrong. It tries to use 32-bit inode numbers on 32-bit arches, but that's
actually not a problem. 32-bit arches can deal with 64-bit inode numbers
just fine when userland code is compiled with LFS support (the common
case these days).
What we really want to do is just use 64-bit numbers everywhere, unless
someone has mounted with the ino32 mount option. In that case, we want
to ensure that we hash the inode number down to something that will fit
in 32 bits before presenting the value to userland.
Add new helper functions that do this, and only do the conversion before
presenting these values to userland in getattr and readdir.
The inode table hashvalue is changed to just cast the inode number to
unsigned long, as low-order bits are the most likely to vary anyway.
While it's not strictly required, we do want to put something in
inode->i_ino. Instead of basing it on BITS_PER_LONG, however, base it on
the size of the ino_t type.
NOTE: This is a user-visible change on 32-bit arches:
1/ inode numbers will be seen to have changed between kernel versions.
32-bit arches will see large inode numbers now instead of the hashed
ones they saw before.
2/ any really old software not built with LFS support may start failing
stat() calls with -EOVERFLOW on inode numbers >2^32. Nothing much we
can do about these, but hopefully the intersection of people running
such code on ceph will be very small.
The workaround for both problems is to mount with "-o ino32".
Lucas Stach [Mon, 24 Aug 2020 10:55:37 +0000 (12:55 +0200)]
drm/etnaviv: always start/stop scheduler in timeout processing
The drm scheduler currently expects that the stop/start sequence is always
executed in the timeout handling, as the job at the head of the hardware
execution list is always removed from the ring mirror before the driver
function is called and only inserted back into the list when starting the
scheduler.
This adds some unnecessary overhead if the timeout handler determines
that the GPU is still executing jobs normally and just wished to extend
the timeout, but a better solution requires a major rearchitecture of the
scheduler, which is not applicable as a fix.
Fixes: 135517d3565b ("drm/scheduler: Avoid accessing freed bad job.") Signed-off-by: Lucas Stach <[email protected]> Tested-by: Russell King <[email protected]>
drm/etnaviv: fix external abort seen on GC600 rev 0x19
It looks like that this GPU core triggers an abort when
reading VIVS_HI_CHIP_PRODUCT_ID and/or VIVS_HI_CHIP_ECO_ID.
I looked at different versions of Vivante's kernel driver and did
not found anything about this issue or what feature flag can be
used. So go the simplest route and do not read these two registers
on the affected GPU core.
Vineeth Pillai [Fri, 21 Aug 2020 15:28:49 +0000 (15:28 +0000)]
hv_utils: drain the timesync packets on onchannelcallback
There could be instances where a system stall prevents the timesync
packets to be consumed. And this might lead to more than one packet
pending in the ring buffer. Current code empties one packet per callback
and it might be a stale one. So drain all the packets from ring buffer
on each callback.
Vineeth Pillai [Fri, 21 Aug 2020 15:25:23 +0000 (15:25 +0000)]
hv_utils: return error if host timesysnc update is stale
If for any reason, host timesync messages were not processed by
the guest, hv_ptp_gettime() returns a stale value and the
caller (clock_gettime, PTP ioctl etc) has no means to know this
now. Return an error so that the caller knows about this.
Dmitry Osipenko [Mon, 17 Aug 2020 23:50:48 +0000 (02:50 +0300)]
mfd: core: Fix double-free in mfd_remove_devices_fn()
The pdev.mfd_cell is released by platform_device_release(), which is
invoked by platform_device_unregister(). Hence mfd_remove_devices_fn()
shouldn't release the cell variable. The double-free bug is reported KASAN
during of MFD driver module removal.
Fixes: 466a62d7642f ("mfd: core: Make a best effort attempt to match devices with the correct of_nodes") Reported-by: Marek Szyprowski <[email protected]> Signed-off-by: Dmitry Osipenko <[email protected]> Signed-off-by: Lee Jones <[email protected]>
Bob Peterson [Fri, 21 Aug 2020 13:50:34 +0000 (08:50 -0500)]
gfs2: add some much needed cleanup for log flushes that fail
When a log flush fails due to io errors, it signals the failure but does
not clean up after itself very well. This is because buffers are added to
the transaction tr_buf and tr_databuf queue, but the io error causes
gfs2_log_flush to bypass the "after_commit" functions responsible for
dequeueing the bd elements. If the bd elements are added to the ail list
before the error, function ail_drain takes care of dequeueing them.
But if they haven't gotten that far, the elements are forgotten and
make the transactions unable to be freed.
This patch introduces new function trans_drain which drains the bd
elements from the transaction so they can be freed properly.
Fixes: f473bf398bf1 ("cpufreq: intel_pstate: Allow raw energy performance preference value") Signed-off-by: Randy Dunlap <[email protected]> Cc: Srinivas Pandruvada <[email protected]> Cc: Rafael J. Wysocki <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
projects / linux.git / log