Stefan Agner [Tue, 13 Jan 2015 23:20:21 +0000 (00:20 +0100)]
net: fec: fix MDIO bus assignement for dual fec SoC's
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Linus Torvalds [Tue, 13 Jan 2015 22:54:12 +0000 (11:54 +1300)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull WRITE_ONCE argument order change from Christian Borntraeger:
"As discussed on LKML[1] it was agreed that WRITE_ONCE(x, val) is
better than ASSIGN_ONCE(val, x)
Lets change that for 3.19 as 3.19 has no user yet, but the first users
will hit linux-next soon"
David Vrabel [Tue, 13 Jan 2015 16:42:42 +0000 (16:42 +0000)]
xen-netfront: use different locks for Rx and Tx stats
In netfront the Rx and Tx path are independent and use different
locks. The Tx lock is held with hard irqs disabled, but Rx lock is
held with only BH disabled. Since both sides use the same stats lock,
a deadlock may occur.
[ INFO: possible irq lock inversion dependency detected ]
3.16.2 #16 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&queue->tx_lock)->rlock){-.....}, at: [<c03adec8>]
xennet_tx_interrupt+0x14/0x34
but this lock took another, HARDIRQ-unsafe lock in the past:
(&stat->syncp.seq#2){+.-...}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Mugunthan V N [Tue, 13 Jan 2015 12:05:49 +0000 (17:35 +0530)]
drivers: net: cpsw: fix multicast flush in dual emac mode
Since ALE table is a common resource for both the interfaces in Dual EMAC
mode and while bringing up the second interface in cpsw_ndo_set_rx_mode()
all the multicast entries added by the first interface is flushed out and
only second interface multicast addresses are added. Fixing this by
flushing multicast addresses based on dual EMAC port vlans which will not
affect the other emac port multicast addresses.
Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation) Cc: <[email protected]> # v3.9+ Signed-off-by: Mugunthan V N <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Simon Guinot [Tue, 2 Dec 2014 15:32:10 +0000 (07:32 -0800)]
leds: netxbig: fix oops at probe time
This patch fixes a NULL pointer dereference on led_dat->mode_val. Due to
this bug, a kernel oops can be observed at probe time on the LaCie 2Big
and 5Big v2 boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
[...]
[<c03f244c>] (netxbig_led_probe) from [<c02c8c6c>] (platform_drv_probe+0x4c/0x9c)
[<c02c8c6c>] (platform_drv_probe) from [<c02c72d0>] (driver_probe_device+0x98/0x25c)
[<c02c72d0>] (driver_probe_device) from [<c02c7520>] (__driver_attach+0x8c/0x90)
[<c02c7520>] (__driver_attach) from [<c02c5c24>] (bus_for_each_dev+0x68/0x94)
[<c02c5c24>] (bus_for_each_dev) from [<c02c6408>] (bus_add_driver+0x124/0x1dc)
[<c02c6408>] (bus_add_driver) from [<c02c7ac0>] (driver_register+0x78/0xf8)
[<c02c7ac0>] (driver_register) from [<c000888c>] (do_one_initcall+0x80/0x1cc)
[<c000888c>] (do_one_initcall) from [<c0733618>] (kernel_init_freeable+0xe4/0x1b4)
[<c0733618>] (kernel_init_freeable) from [<c058db9c>] (kernel_init+0xc/0xec)
[<c058db9c>] (kernel_init) from [<c0009850>] (ret_from_fork+0x14/0x24)
[...]
Linus Torvalds [Tue, 13 Jan 2015 19:09:14 +0000 (08:09 +1300)]
Merge tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"This update contains three patches to fix one compile error, and two
run-time bugs. One of them fixes infinite loop on ARM"
* tag 'linux-kselftest-3.19-rc-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/vm: fix link error for transhuge-stress test
tools: testing: selftests: mq_perf_tests: Fix infinite loop on ARM
selftests/exec: allow shell return code of 126
Linus Torvalds [Tue, 13 Jan 2015 19:07:42 +0000 (08:07 +1300)]
Merge tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
"Several critical linear p2m fixes that prevented some hosts from
booting"
* tag 'stable/for-linus-3.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: properly retrieve NMI reason
xen: check for zero sized area when invalidating memory
xen: use correct type for physical addresses
xen: correct race in alloc_p2m_pmd()
xen: correct error for building p2m list on 32 bits
x86/xen: avoid freeing static 'name' when kasprintf() fails
x86/xen: add extra memory for remapped frames during setup
x86/xen: don't count how many PFNs are identity mapped
x86/xen: Free bootmem in free_p2m_page() during early boot
x86/xen: Remove unnecessary BUG_ON(preemptible()) in xen_setup_timer()
The "smemc" clock is removed on BG2Q SoCs. In fact, bit19 of clkenable
register is for nfc. Current code use bit19 for non-exist "smemc"
incorrectly, this prevents eMMC from working due to the sdhci's
"core" clk is still gated.
Boris Brezillon [Tue, 13 Jan 2015 14:44:06 +0000 (15:44 +0100)]
clk: at91: keep slow clk enabled to prevent system hang
All slow clk users are not properly claiming it (get + prepare + enable)
before using it.
If all users properly claiming this clock release it, the clock is
disabled, but faulty users still depends on it, and the system hangs.
This fix prevents the slow clock from being disabled, and should solve the
hanging issue, but offending drivers should be patched to properly claim
this clock.
Linus Torvalds [Tue, 13 Jan 2015 18:53:51 +0000 (07:53 +1300)]
Merge branch 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- Fix a problem that Intel SoC DTS thermal driver does not work when
CONFIG_THERMAL_INT340X is not set.
- Fix a NULL pointer dereference when processor_thermal_device driver
is loaded on a platform without ACPI support"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
int340x_thermal/processor_thermal_device: return failure when
ACPI/int340x_thermal: enumerate INT3401 for Intel SoC DTS thermal driver
ACPI/int340x_thermal: enumerate INT340X devices even if they're not in _ART/_TRT
Andy Shevchenko [Tue, 13 Jan 2015 16:57:15 +0000 (18:57 +0200)]
dmaengine: dw: balance PM runtime calls
In case of PCI driver we will get a warning:
dw_dmac_pci 0000:00:18.0: Unbalanced pm_runtime_enable!
dw_dmac_pci 0000:00:18.0: DesignWare DMA Controller, 8 channels
This happens due to pm_runtime_enable() call from the driver when PM runtime is
enabled by core.
This patch moves that call to the platform driver where it might make sense.
Arnd Bergmann [Tue, 13 Jan 2015 14:25:11 +0000 (15:25 +0100)]
usb: phy: mv-usb: fix usb_phy build errors
The driver was recently adapted to a core API change, but the
change was incomplete, missing out the suspend helper and
leaving an extraneous local variable around:
usb/phy/phy-mv-usb.c: In function 'mv_otg_update_state':
usb/phy/phy-mv-usb.c:341:18: warning: unused variable 'phy' [-Wunused-variable]
usb/phy/phy-mv-usb.c: In function 'mv_otg_suspend':
usb/phy/phy-mv-usb.c:861:16: error: 'struct usb_phy' has no member named 'state'
Signed-off-by: Arnd Bergmann <[email protected]> Fixes: e47d92545c297 ("usb: move the OTG state from the USB PHY to the OTG structure") Signed-off-by: Felipe Balbi <[email protected]>
moves the call to fl->fl_lmops->lm_change() to a place in the
code where fl might be a non-lease lock.
When that happens, fl_lmops is NULL and an Oops ensures.
So add an extra test to restore correct functioning.
Hans de Goede [Mon, 5 Jan 2015 08:15:16 +0000 (09:15 +0100)]
simplefb: Fix build failure on Sparc
of_platform_device_create is only defined when CONFIG_OF_ADDRESS is set,
which is normally always the case when CONFIG_OF is defined, except on Sparc,
so explicitly check for CONFIG_OF_ADDRESS rather then for CONFIG_OF.
Jan Beulich [Tue, 13 Jan 2015 07:40:05 +0000 (07:40 +0000)]
x86/xen: properly retrieve NMI reason
Using the native code here can't work properly, as the hypervisor would
normally have cleared the two reason bits by the time Dom0 gets to see
the NMI (if passed to it at all). There's a shared info field for this,
and there's an existing hook to use - just fit the two together. This
is particularly relevant so that NMIs intended to be handled by APEI /
GHES actually make it to the respective handler.
Note that the hook can (and should) be used irrespective of whether
being in Dom0, as accessing port 0x61 in a DomU would be even worse,
while the shared info field would just hold zero all the time. Note
further that hardware NMI handling for PVH doesn't currently work
anyway due to missing code in the hypervisor (but it is expected to
work the native rather than the PV way).
if m_td1TD1.byTCR has TCR_EDP and TCR_STP are set, the interrupt handler will
try and complete the buffer before it is completed. Usually on the tail
of a burst of tx packets.
This results in a partially completed packet being transmitted or worse
sitll dead lock when skb is freed by the interrupt handler.
Set head_td->m_td1TD1.byTCR to 0 in first lock of vnt_tx_packet to stop
interrupt handler completing the buffer. Move Set TSR1 & ReqCount in
s_cbFillTxBufHead to the second lock.
cbReqCount is carried to the second lock in pTDInfo->dwReqCount without
the padding removed.
Linus Torvalds [Tue, 13 Jan 2015 02:29:42 +0000 (15:29 +1300)]
Merge tag 'gpio-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Here are some GPIO fixes, mainly affecting the DLN2 IRQ handling.
Nothing special about them, just fixes:
- Three patches fixing IRQ handling for the DLN2
- Null pointer handling for grgpio"
* tag 'gpio-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: dln2: use bus_sync_unlock instead of scheduling work
gpio: grgpio: Avoid potential NULL pointer dereference
gpio: dln2: Fix gpio output value in dln2_gpio_direction_output()
gpio: dln2: fix issue when an IRQ is unmasked then enabled
Linus Torvalds [Tue, 13 Jan 2015 02:25:23 +0000 (15:25 +1300)]
Merge tag 'mmc-v3.19-3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"MMC host:
- sdhci-pci|acpi: Support some new IDs
- sdhci: Fix sleep from atomic context
- sdhci-pxav3: Prevent hang during ->probe()
- sdhci: Disable re-tuning for HS400"
* tag 'mmc-v3.19-3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-pci: Add support for Intel SPT
mmc: sdhci-acpi: Add ACPI HID INT344D
mmc: sdhci: Fix sleep in atomic after inserting SD card
mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
mmc: sdhci: Disable re-tuning for HS400
mmc: sdhci: Simplify use of tuning timer
mmc: sdhci: Add out_unlock to sdhci_execute_tuning
mmc: sdhci: Tuning should not change max_blk_count
Pull scsi target fixes from Nicholas Bellinger:
"Mostly minor fixes this time, including:
- Add missing virtio-scsi -> TCM attribute conversion in vhost-scsi.
- Fix persistent reservations write exclusive handling to allow
readers for all registered I_T nexuses.
- Drop arbitrary maximum I/O size limit in order to process I/Os
larger than 4 MB, required for initiators that don't honor block
limits EVPD.
- Drop the now left-over fabric_max_sectors attribute"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix typos in enum cmd_flags_table
MAINTAINERS: Add entry for iSER target driver
target: Allow Write Exclusive non-reservation holders to READ
target: Drop left-over fabric_max_sectors attribute
target: Drop arbitrary maximum I/O size limit
Documentation/target: Update fabric_ops to latest code
vhost-scsi: Add missing virtio-scsi -> TCM attribute conversion
Will Deacon [Mon, 12 Jan 2015 19:10:55 +0000 (19:10 +0000)]
mm: mmu_gather: use tlb->end != 0 only for TLB invalidation
When batching up address ranges for TLB invalidation, we check tlb->end
!= 0 to indicate that some pages have actually been unmapped.
As of commit f045bbb9fa1b ("mmu_gather: fix over-eager
tlb_flush_mmu_free() calling"), we use the same check for freeing these
pages in order to avoid a performance regression where we call
free_pages_and_swap_cache even when no pages are actually queued up.
Unfortunately, the range could have been reset (tlb->end = 0) by
tlb_end_vma, which has been shown to cause memory leaks on arm64.
Furthermore, investigation into these leaks revealed that the fullmm
case on task exit no longer invalidates the TLB, by virtue of tlb->end
== 0 (in 3.18, need_flush would have been set).
This patch resolves the problem by reverting commit f045bbb9fa1b, using
instead tlb->local.nr as the predicate for page freeing in
tlb_flush_mmu_free and ensuring that tlb->end is initialised to a
non-zero value in the fullmm case.
Merge tag 'v3.19-rockhip-clkfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-fixes
- two currently unused clocks that need to stay enabled
- fix the lock bit locations of the rk3066 plls
- fix rk3288 core divider values to the ones actually
specified by the soc vendor
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
Commit e4c7f259c5be ("USB: kaweth.c: use GFP_ATOMIC under spin_lock")
makes sure that kaweth_internal_control_msg() allocates memory with GFP_ATOMIC,
but kaweth_internal_control_msg() also calls usb_start_wait_urb()
that still allocates memory with GFP_NOIO.
The patch fixes usb_start_wait_urb() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Jon Paul Maloy [Thu, 8 Jan 2015 17:27:27 +0000 (12:27 -0500)]
tipc: fix bug in broadcast retransmit code
In commit 58dc55f25631178ee74cd27185956a8f7dcb3e32 ("tipc: use generic
SKB list APIs to manage link transmission queue") we replace all list
traversal loops with the macros skb_queue_walk() or
skb_queue_walk_safe(). While the previous loops were based on the
assumption that the list was NULL-terminated, the standard macros
stop when the iterator reaches the list head, which is non-NULL.
In the function bclink_retransmit_pkt() this macro replacement has
lead to a bug. When we receive a BCAST STATE_MSG we unconditionally
call the function bclink_retransmit_pkt(), whether there really is
anything to retransmit or not, assuming that the sequence number
comparisons will lead to the correct behavior. However, if the
transmission queue is empty, or if there are no eligible buffers in
the transmission queue, we will by mistake pass the list head pointer
to the function tipc_link_retransmit(). Since the list head is not a
valid sk_buff, this leads to a crash.
In this commit we fix this by only calling tipc_link_retransmit()
if we actually found eligible buffers in the transmission queue.
isdn: fix NUL (\0 or \x00) specification in string
In C one can either use '\0' or '\x00' (or '\000') to add a NUL byte to
a string. '\0x00' isn't part of these and will in fact result in a
single NUL followed by "x00". This fixes that.
Signed-off-by: Giel van Schijndel <[email protected]>
Reported-at: http://www.viva64.com/en/b/0299/ Signed-off-by: David S. Miller <[email protected]>
Merge tag 'fixes-for-v3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc5
Just three fixes this time. An oops fix in ep_write() from gadgetfs,
another oops for the Atmel UDC when unloading a gadget driver and
the fix for PHY deferred probing.
Signed-off-by: Felipe Balbi <[email protected]>
Conflicts:
drivers/usb/phy/phy.c
Alexander Stein [Fri, 5 Dec 2014 13:31:39 +0000 (14:31 +0100)]
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
atmel_lcdfb needs also uses hclk clock, but AT91SAM9263 doesn't have that
specific clock, so use lcd_clk twice. The same was done in
arch/arm/mach-at91/at91sam9263.c
Marc Zyngier [Sun, 11 Jan 2015 13:10:11 +0000 (14:10 +0100)]
arm64: KVM: Fix HCR setting for 32bit guests
Commit b856a59141b1 (arm/arm64: KVM: Reset the HCR on each vcpu
when resetting the vcpu) moved the init of the HCR register to
happen later in the init of a vcpu, but left out the fixup
done in kvm_reset_vcpu when preparing for a 32bit guest.
As a result, the 32bit guest is run as a 64bit guest, but the
rest of the kernel still manages it as a 32bit. Fun follows.
Moving the fixup to vcpu_reset_hcr solves the problem for good.
Marc Zyngier [Sun, 11 Jan 2015 13:10:10 +0000 (14:10 +0100)]
arm64: KVM: Fix TLB invalidation by IPA/VMID
It took about two years for someone to notice that the IPA passed
to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing
is not as good as it should be...
Juergen Gross [Mon, 12 Jan 2015 05:05:10 +0000 (06:05 +0100)]
xen: check for zero sized area when invalidating memory
With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Juergen Gross [Mon, 12 Jan 2015 05:05:08 +0000 (06:05 +0100)]
xen: correct race in alloc_p2m_pmd()
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Juergen Gross [Mon, 12 Jan 2015 05:05:07 +0000 (06:05 +0100)]
xen: correct error for building p2m list on 32 bits
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Jan Willeke [Thu, 8 Jan 2015 15:56:01 +0000 (16:56 +0100)]
s390/uprobes: fix user space PER events
If uprobes are single stepped for example with gdb, the behavior should
now be correct. Before this patch, when gdb was single stepping a uprobe,
the result was a SIGILL.
When PER is active for any storage alteration and a uprobe is hit, a storage
alteration event is indicated. These over indications are filterd out by gdb,
if no change has happened within the observed area.
Jeremiah Mahler [Sun, 11 Jan 2015 13:42:07 +0000 (05:42 -0800)]
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
If a USB serial device (e.g. /dev/ttyUSB0) with an active program is
unplugged, an -ENODEV (19) error will be produced after it gives up
trying to resubmit a read.
Jeremiah Mahler [Sun, 11 Jan 2015 13:42:06 +0000 (05:42 -0800)]
usb: serial: silence all non-critical read errors
If a USB serial device is unplugged while there is an active program
using the device it may spam the logs with -EPROTO (71) messages as it
attempts to retry.
Most serial usb drivers (metro-usb, pl2303, mos7840, ...) only output
these messages for debugging. The generic driver treats these as
errors.
Change the default output for the generic serial driver from error to
debug to silence these non-critical errors.
mmc: sdhci: Fix sleep in atomic after inserting SD card
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Thomas Petazzoni [Wed, 31 Dec 2014 10:54:10 +0000 (11:54 +0100)]
mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
In commit 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Cc: <[email protected]> # v3.15+ Signed-off-by: Thomas Petazzoni <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
Adrian Hunter [Fri, 5 Dec 2014 17:25:31 +0000 (19:25 +0200)]
mmc: sdhci: Disable re-tuning for HS400
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Adrian Hunter [Fri, 5 Dec 2014 17:25:30 +0000 (19:25 +0200)]
mmc: sdhci: Simplify use of tuning timer
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Adrian Hunter [Fri, 5 Dec 2014 17:25:28 +0000 (19:25 +0200)]
mmc: sdhci: Tuning should not change max_blk_count
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
ARM: exynos_defconfig: Enable options for display panel support
Many Exynos devices have a display panel. Most of them just have
a simple panel while others have more complex configurations that
requires an embedded DisplayPort (eDP) to LVDS bridges.
This patch enables the following features to be built in the kernel
image to support both setups:
- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
powerpc: Work around gcc bug in current_thread_info()
In commit a3e5b356b3ab "powerpc: Don't use local named register variable
in current_thread_info" Anton changed the way we did current_thread_info()
to accommodate LLVM, and it was not meant to have any effect elsewhere.
Unfortunately it has exposed a gcc bug, where r1 gets copied into
another register and then gcc uses that register to restore the toc
after a function call, even when that register is volatile and has been
clobbered by the function call.
We could revert Anton's patch, but it's not clear the original code is
safe either, we may just have been lucky.
The cleanest solution is to just use the existing CURRENT_THREAD_INFO()
asm macro, and call it using inline asm.
Segher points out we don't need volatile on the asm, if the result of
the shift is unused it's fine for the compiler to elide it.
Fixes: a3e5b356b3ab ("powerpc: Don't use local named register variable in current_thread_info") Reported-by: Alexander Graf <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
Ian Munsie [Wed, 7 Jan 2015 05:33:04 +0000 (16:33 +1100)]
cxl: Fix issues when unmapping contexts
An issue was introduced with "cxl: Unmap MMIO regions when detaching a
context" (b123429e6a9e8d03aacf888d23262835f0081448) where closing a
context normally could also unmap the problem state area of other
contexts currently using the AFU.
It was also discovered that after a context's MMIO space had been
unmapped it would read 0s when accessing it, whereas the expected
behaviour was for the access to fail altogether.
In order to address these issues, this patch does two things:
- Forced mmap unmapping is only done when we are forcefully detaching
all contexts, and not in the normal detach path. Since the normal
context close path is tied to the file release any mmaps must have
already been released so we don't need to worry in that case.
- The mmap path now uses a vm_operations_struct with a fault handler.
The fault handler ensures that the context is in started state,
otherwise it fails the access attempt with a SIGBUS.
Fixes: b123429e6a9e ("cxl: Unmap MMIO regions when detaching a context") Signed-off-by: Ian Munsie <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
The store was originally used to save the current tracepoint status
so the entry and the exit tracepoints were always balanced. In the
end I just created a separate path when tracepoints are enabled.
The offset on the stack used for this store is not valid for ABIv2
and it causes strange issues. I noticed it because OPAL console input
was broken.
David S. Miller [Mon, 12 Jan 2015 05:23:45 +0000 (00:23 -0500)]
Merge tag 'wireless-drivers-for-davem-2015-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
* rtlwifi: fix a regression in large skb allocation failure
iwlwifi:
* fix for 7265D NVM check
* fixes for scan: fix long scanning times and network discovery
* new firmware API for iwlmvm supported devices
* fixes in rate control
Christoph Jaeger [Sun, 11 Jan 2015 18:01:16 +0000 (13:01 -0500)]
packet: bail out of packet_snd() if L2 header creation fails
Due to a misplaced parenthesis, the expression
(unlikely(offset) < 0),
which expands to
(__builtin_expect(!!(offset), 0) < 0),
never evaluates to true. Therefore, when sending packets with
PF_PACKET/SOCK_DGRAM, packet_snd() does not abort as intended
if the creation of the layer 2 header fails.
Spotted by Coverity - CID 1259975 ("Operands don't affect result").
Eric Dumazet [Sun, 11 Jan 2015 18:32:18 +0000 (10:32 -0800)]
alx: fix alx_poll()
Commit d75b1ade567f ("net: less interrupt masking in NAPI") uncovered
wrong alx_poll() behavior.
A NAPI poll() handler is supposed to return exactly the budget when/if
napi_complete() has not been called.
It is also supposed to return number of frames that were received, so
that netdev_budget can have a meaning.
Also, in case of TX pressure, we still have to dequeue received
packets : alx_clean_rx_irq() has to be called even if
alx_clean_tx_irq(alx) returns false, otherwise device is half duplex.
Linus Torvalds [Sun, 11 Jan 2015 20:44:10 +0000 (12:44 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three small fixes from over the Christmas period, and wiring up the
new execveat syscall for ARM"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
ARM: 8249/1: mm: dump: don't skip regions
ARM: wire up execveat syscall
Linus Torvalds [Sun, 11 Jan 2015 19:51:49 +0000 (11:51 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: group scheduling corner case fix, two deadline scheduler
fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
system fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
sched/deadline: Avoid double-accounting in case of missed deadlines
sched/deadline: Fix migration of SCHED_DEADLINE tasks
sched: Fix odd values in effective_load() calculations
sched, fanotify: Deal with nested sleeps
sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
Linus Torvalds [Sun, 11 Jan 2015 19:47:45 +0000 (11:47 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
Linus Torvalds [Sun, 11 Jan 2015 19:46:31 +0000 (11:46 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"A liblockdep fix and a mutex_unlock() mutex-debugging fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Always clear owner field upon mutex_unlock()
tools/liblockdep: Fix debug_check thinko in mutex destroy
mm: fix corner case in anon_vma endless growing prevention
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208e662 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Linus Torvalds [Sun, 11 Jan 2015 19:33:57 +0000 (11:33 -0800)]
mm: Don't count the stack guard page towards RLIMIT_STACK
Commit fee7e49d4514 ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions. It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".
Somebody did notice. Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.
So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Johan Hovold [Mon, 5 Jan 2015 15:04:12 +0000 (16:04 +0100)]
USB: console: fix uninitialised ldisc semaphore
The USB console currently allocates a temporary fake tty which is used
to pass terminal settings to the underlying serial driver.
The tty struct is not fully initialised, something which can lead to a
lockdep warning (or worse) if a serial driver tries to acquire a
line-discipline reference:
usbserial: USB Serial support registered for pl2303
pl2303 1-2.1:1.0: pl2303 converter detected
usb 1-2.1: pl2303 converter now attached to ttyUSB0
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 68 Comm: udevd Tainted: G W 3.18.0-rc5 #10
[<c0016f04>] (unwind_backtrace) from [<c0013978>] (show_stack+0x20/0x24)
[<c0013978>] (show_stack) from [<c0449794>] (dump_stack+0x24/0x28)
[<c0449794>] (dump_stack) from [<c006f730>] (__lock_acquire+0x1e50/0x2004)
[<c006f730>] (__lock_acquire) from [<c0070128>] (lock_acquire+0xe4/0x18c)
[<c0070128>] (lock_acquire) from [<c027c6f8>] (ldsem_down_read_trylock+0x78/0x90)
[<c027c6f8>] (ldsem_down_read_trylock) from [<c027a1cc>] (tty_ldisc_ref+0x24/0x58)
[<c027a1cc>] (tty_ldisc_ref) from [<c0340760>] (usb_serial_handle_dcd_change+0x48/0xe8)
[<c0340760>] (usb_serial_handle_dcd_change) from [<bf000484>] (pl2303_read_int_callback+0x210/0x220 [pl2303])
[<bf000484>] (pl2303_read_int_callback [pl2303]) from [<c031624c>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c031624c>] (__usb_hcd_giveback_urb) from [<c0316fc0>] (usb_giveback_urb_bh+0x98/0xd4)
[<c0316fc0>] (usb_giveback_urb_bh) from [<c0042e44>] (tasklet_hi_action+0x9c/0x108)
[<c0042e44>] (tasklet_hi_action) from [<c0042380>] (__do_softirq+0x148/0x42c)
[<c0042380>] (__do_softirq) from [<c00429cc>] (irq_exit+0xd8/0x114)
[<c00429cc>] (irq_exit) from [<c007ae58>] (__handle_domain_irq+0x84/0xdc)
[<c007ae58>] (__handle_domain_irq) from [<c000879c>] (omap_intc_handle_irq+0xd8/0xe0)
[<c000879c>] (omap_intc_handle_irq) from [<c0014544>] (__irq_svc+0x44/0x7c)
Exception stack(0xdf4e7f08 to 0xdf4e7f50)
7f00: debc0b80df4e7f5c0000000000000000debc0b80be8da96c
7f20: 0000000000000128c000fc84df4e600000000000df4e7f9400000004df4e7f50
7f40: c038ebc0c038d74c600f0013ffffffff
[<c0014544>] (__irq_svc) from [<c038d74c>] (___sys_sendmsg.part.29+0x0/0x2e0)
[<c038d74c>] (___sys_sendmsg.part.29) from [<c038ec08>] (SyS_sendmsg+0x18/0x1c)
[<c038ec08>] (SyS_sendmsg) from [<c000fa00>] (ret_fast_syscall+0x0/0x48)
console [ttyUSB0] enabled
Fixes: 36697529b5bb ("tty: Replace ldisc locking with ldisc_sem") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
Linus Torvalds [Sat, 10 Jan 2015 05:23:27 +0000 (21:23 -0800)]
Merge tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All a few small regression or stable fixes: a Nvidia HDMI ID addition,
a regression fix for CAIAQ stream count, a typo fix for GPIO setup
with STAC/IDT HD-audio codecs, and a Fireworks big-endian fix"
* tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireworks: fix an endianness bug for transaction length
ALSA: hda - Add new GPU codec ID 0x10de0072 to snd-hda
ALSA: hda - Fix wrong gpio_dir & gpio_mask hint setups for IDT/STAC codecs
ALSA: snd-usb-caiaq: fix stream count check
Linus Torvalds [Sat, 10 Jan 2015 05:18:48 +0000 (21:18 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- bounds checking fixes in logitech and roccat drivers, from Peter Wu
and Dan Carpenter
- double-kfree fix in i2c-hid driver on bus shutdown, from Mika
Westerberg
- a couple of various small driver fixes
- a few device id additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: roccat: potential out of bounds in pyra_sysfs_write_settings()
HID: Add a new id 0x501a for Genius MousePen i608X
HID: logitech-hidpp: prefix the name with "Logitech"
HID: logitech-hidpp: avoid unintended fall-through
HID: Allow HID_BATTERY_STRENGTH to be enabled
HID: i2c-hid: Do not free buffers in i2c_hid_stop()
HID: add battery quirk for USB_DEVICE_ID_APPLE_ALU_WIRELESS_2011_ISO keyboard
HID: logitech-hidpp: check WTP report length
HID: logitech-dj: check report length
Linus Torvalds [Sat, 10 Jan 2015 05:13:34 +0000 (21:13 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I'm briefly working between holidays and LCA, so this is close to a
couple of weeks of fixes,
Two sets of amdkfd fixes, this is a new feature this kernel, and this
pull fixes a few issues since it got merged, ordering when built-in to
kernel and also the iommu vs gpu ordering patch, it also reworks the
ioctl before the initial release.
Otherwise:
- radeon: some misc fixes all over, hdmi, 4k, dpm
- nouveau: mcp77 init fixes, oops fix, bug on fix, msi fix
- i915: power fixes, revert VGACNTR patch
Probably be quiteer next week since I'll be at LCA anyways"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm/amdkfd: rewrite kfd_ioctl() according to drm_ioctl()
drm/amdkfd: reformat IOCTL definitions to drm-style
drm/amdkfd: Do copy_to/from_user in general kfd_ioctl()
drm/radeon: integer underflow in radeon_cp_dispatch_texture()
drm/radeon: adjust default bapm settings for KV
drm/radeon: properly filter DP1.2 4k modes on non-DP1.2 hw
drm/radeon: fix sad_count check for dce3
drm/radeon: KV has three PPLLs (v2)
drm/amdkfd: unmap VMID<-->PASID when relesing VMID (non-HWS)
drm/radeon: Init amdkfd only if it was compiled
amdkfd: actually allocate longs for the pasid bitmask
drm/nouveau/nouveau: Do not BUG_ON(!spin_is_locked()) on UP
drm/nv4c/mc: disable msi
drm/nouveau/fb/ram/mcp77: enable NISO poller
drm/nouveau/fb/ram/mcp77: use carveout reg to determine size
drm/nouveau/fb/ram/mcp77: subclass nouveau_ram
drm/nouveau: wake up the card if necessary during gem callbacks
drm/nouveau/device: Add support for GK208B, resolves bug 86935
drm/nouveau: fix missing return statement in nouveau_ttm_tt_unpopulate
drm/nouveau/bios: fix oops on pre-nv50 chipsets
...
Linus Torvalds [Sat, 10 Jan 2015 04:57:58 +0000 (20:57 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here is a handful of minor arm64 fixes discovered and fixed over the
Christmas break. The main part is adding some missing #includes that
we seem to be getting transitively but have started causing problems
in -next.
- Fix early mapping fixmap corruption by EFI runtime services
- Fix __NR_compat_syscalls off-by-one
- Add missing sanity checks for some 32-bit registers
- Add some missing #includes which we get transitively
- Remove unused prepare_to_copy() macro"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/efi: add missing call to early_ioremap_reset()
arm64: fix missing asm/io.h include in kernel/smp_spin_table.c
arm64: fix missing asm/alternative.h include in kernel/module.c
arm64: fix missing linux/bug.h include in asm/arch_timer.h
arm64: fix missing asm/pgtable-hwdef.h include in asm/processor.h
arm64: sanity checks: add missing AArch32 registers
arm64: Remove unused prepare_to_copy()
arm64: Correct __NR_compat_syscalls for bpf
Fixes
- kgdb/kdb: Allow access on a single core, if a CPU round up is
deemed impossible, which will allow inspection of the now "trashed"
kernel
- kdb: Add enable mask for the command groups
- kdb: access controls to restrict sensitive commands"
* tag 'for_linus-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kernel/debug/debug_core.c: Logging clean-up
kgdb: timeout if secondary CPUs ignore the roundup
kdb: Allow access to sensitive commands to be restricted by default
kdb: Add enable mask for groups of commands
kdb: Categorize kdb commands (similar to SysRq categorization)
kdb: Remove KDB_REPEAT_NONE flag
kdb: Use KDB_REPEAT_* values as flags
kdb: Rename kdb_register_repeat() to kdb_register_flags()
kdb: Rename kdb_repeat_t to kdb_cmdflags_t, cmd_repeat to cmd_flags
kdb: Remove currently unused kdbtab_t->cmd_flags
Linus Torvalds [Sat, 10 Jan 2015 01:55:00 +0000 (17:55 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two Ceph fixes from Sage Weil:
"These are both pretty trivial: a sparse warning fix and size_t printk
thing"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix sparse endianness warnings
ceph: use %zu for len in ceph_fill_inline_data()
Linus Torvalds [Sat, 10 Jan 2015 01:46:07 +0000 (17:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"None of these are huge, but my commit does fix a regression from 3.18
that could cause lost files during log replay.
This also adds Dave Sterba to the list of Btrfs maintainers. It
doesn't mean we're doing things differently, but Dave has really been
helping with the maintainer workload for years"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: don't delay inode ref updates during log replay
Btrfs: correctly get tree level in tree_backref_for_extent
Btrfs: call inode_dec_link_count() on mkdir error path
Btrfs: abort transaction if we don't find the block group
Btrfs, scrub: uninitialized variable in scrub_extent_for_parity()
Btrfs: add more maintainers
Songjun Wu [Fri, 9 Jan 2015 16:11:24 +0000 (17:11 +0100)]
usb: gadget: udc: atmel: fix possible oops when unloading module
When unloading the module 'g_hid.ko', the urb request will be dequeued and the
completion routine will be excuted. If there is no urb packet, the urb request
will not be added to the endpoint queue and the completion routine pointer in
urb request is NULL.
Accessing to this NULL function pointer will cause the Oops issue reported
below.
Add the code to check if the urb request is in the endpoint queue
or not. If the urb request is not in the endpoint queue, a negative
error code will be returned.
Returning a difference from a comparison functions is usually wrong
(see acbbe6fbb240 "kcmp: fix standard comparison bug" for the long
story). Here there is the additional twist that if the void pointers
ns and kn->ns happen to differ by a multiple of 2^32,
kernfs_name_compare returns 0, falsely reporting a match to the
caller.
Technically 'hash - kn->hash' is ok since the hashes are restricted to
31 bits, but it's better to avoid that subtlety.
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
Currently it is not possible to have a kernel with built-in MCB attached
devices. This results out of the fact that mcb-pci requests PCI BAR 0, then
parses the chameleon table and calls the driver's probe function before
releasing BAR 0 again. When building the kernel with modules this is not a
problem (and therefore it wasn't detected by my tests yet).
A solution is to only remap the 1st 0x200 bytes of a Chameleon PCI device.
0x200 bytes is the maximum size of a Chameleon v2 Table.
Also this patch stops disabling the PCI device on successful registration of MCB
devices.
target: Drop left-over fabric_max_sectors attribute
Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.
This patch drops the arbitrary maximum I/O size limit in sbc_parse_cdb(),
which currently for fabric_max_sectors is hardcoded to 8192 (4 MB for 512
byte sector devices), and for hw_max_sectors is a backend driver dependent
value.
This limit is problematic because Linux initiators have only recently
started to honor block limits MAXIMUM TRANSFER LENGTH, and other non-Linux
based initiators (eg: MSFT Fibre Channel) can also generate I/Os larger
than 4 MB in size.
Currently when this happens, the following message will appear on the
target resulting in I/Os being returned with non recoverable status:
SCSI OP 28h with too big sectors 16384 exceeds fabric_max_sectors: 8192
Instead, drop both [fabric,hw]_max_sector checks in sbc_parse_cdb(),
and convert the existing hw_max_sectors into a purely informational
attribute used to represent the granuality that backend driver and/or
subsystem code is splitting I/Os upon.
Also, update FILEIO with an explicit FD_MAX_BYTES check in fd_execute_rw()
to deal with the one special iovec limitiation case.
v2 changes:
- Drop hw_max_sectors check in sbc_parse_cdb()
projects / linux.git / log