Miquel Raynal [Wed, 12 Dec 2018 09:36:40 +0000 (10:36 +0100)]
thermal: armada: add overheat interrupt support
The IP can manage to trigger interrupts on overheat situation from all
the sensors.
However, the interrupt source changes along with the last selected
source (ie. the last read sensor), which is an inconsistent behavior.
Avoid possible glitches by always selecting back only one channel which
will then be referenced as the "overheat_sensor" (arbitrarily: the first
in the DT which has a critical trip point filled in).
It is possible that the scan of all thermal zone nodes did not bring a
critical trip point from which the overheat interrupt could be
configured. In this case just complain but do not fail the probe.
Also disable sensor switch during overheat situations because changing
the channel while the system is too hot could clear the overheat state
by changing the source while the temperature is still very high.
Even if the overheat state is not declared, overheat interrupt must be
cleared by reading the DFX interrupt cause _after_ the temperature has
fallen down to the low threshold, otherwise future possible interrupts
would not be served. A work polls the corresponding register until the
overheat flag gets cleared in this case.
Anson Huang [Wed, 21 Nov 2018 05:49:36 +0000 (05:49 +0000)]
thermal: imx: fix for dependency on cpu-freq
The thermal driver is a standalone driver for monitoring SoC temperature
by enabling thermal sensor, so it can be enabled even when CONFIG_CPU_FREQ
is NOT set. So remove the dependency with CPU_THERMAL.
Introduce dummy function of legacy cooling register/unregister to make
thermal driver probe successfully when CONFIG_CPU_FREQ is NOT set.
thermal: tsens: qcom: do not create duplicate regmap debugfs entries
Regmap would use device name to create debugfs entries. If the device
has multiple regmaps it is recommended to use name field in regmap_config.
Fix this by providing name to the regmap configs correctly.
Without this patch we would see below error on DB820c.
qcom-tsens 4a9000.thermal-sensor: Failed to create 4a9000.thermal-sensor
debugfs directory
Matthias Brugger [Sun, 21 Oct 2018 21:58:48 +0000 (23:58 +0200)]
thermal: bcm2835: enable hwmon explicitly
By defaul of-based thermal driver do not enable hwmon.
This patch does this explicitly, so that the temperature can be read
through the common hwmon sysfs.
thermal: hwmon: inline helpers when CONFIG_THERMAL_HWMON is not set
Avoid warnings like this:
thermal_hwmon.h:29:1: warning: ‘thermal_remove_hwmon_sysfs’ defined but not used [-Wunused-function]
thermal_remove_hwmon_sysfs(struct thermal_zone_device *tz)
Fixes: 0dd88793aacd ("thermal: hwmon: move hwmon support to single file") Reviewed-by: Geert Uytterhoeven <[email protected]> Signed-off-by: Eduardo Valentin <[email protected]>
Sinan Kaya [Sun, 30 Dec 2018 20:40:05 +0000 (20:40 +0000)]
ACPI: Fix build failure when CONFIG_NLS is set to 'n'
Observing link failure as follows when CONFIG_ACPI is set but
both CONFIG_NLS and CONFIG_PCI are no set:
drivers/acpi/device_sysfs.o: In function `description_show':
device_sysfs.c:(.text+0x48a): undefined reference to `utf16s_to_utf8s'
This issue was previously addressed implicitly by commit 8a226e00eeed
(PCI: pci-label: Fix build failure when CONFIG_NLS is set to 'm' by
allmodconfig) causing PCI_LABEL to be selected when ACPI was set
which caused NLS to be selected too in that case.
However, after commit 5d32a66541c46 (PCI/ACPI: Allow ACPI to be built
without CONFIG_PCI set) it is possible to build ACPI support without
PCI, so make ACPI select NLS directly to cover that case.
Fixes: 5d32a66541c46 (PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set) Signed-off-by: Sinan Kaya <[email protected]>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <[email protected]>
Richard Zhu [Fri, 21 Dec 2018 04:33:38 +0000 (04:33 +0000)]
PCI: imx: Enable MSI from downstream components
The MSI Enable bit in the MSI Capability (PCIe r4.0, sec 7.7.1.2) controls
whether a Function can request service using MSI.
i.MX6 Root Ports implement the MSI Capability and may use MSI to request
service for events like PME, hotplug, AER, etc. In addition, on i.MX6, the
MSI Enable bit controls delivery of MSI interrupts from components below
the Root Port.
Prior to f3fdfc4ac3a2 ("PCI: Remove host driver Kconfig selection of
CONFIG_PCIEPORTBUS"), enabling CONFIG_PCI_IMX6 automatically also enabled
CONFIG_PCIEPORTBUS, and when portdrv claimed the Root Ports, it set the MSI
Enable bit so it could use PME, hotplug, AER, etc. As a side effect, that
also enabled delivery of MSI interrupts from downstream components.
The imx6q-pcie driver itself does not depend on portdrv, so set MSI Enable
in imx6q-pcie so MSI from downstream components works even if nobody uses
MSI for the Root Port events.
Sebastian Ott [Fri, 21 Dec 2018 14:14:19 +0000 (15:14 +0100)]
PCI/IOV: Add flag so platforms can skip VF scanning
Provide a flag to skip scanning for new VFs after SR-IOV enablement. This
can be set by implementations for which the VFs are already reported by
other means.
Linus Torvalds [Tue, 1 Jan 2019 23:55:29 +0000 (15:55 -0800)]
Merge tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
Linus Torvalds [Tue, 1 Jan 2019 23:45:48 +0000 (15:45 -0800)]
Merge tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This includes a new driver, removes R-Mobile APE6 as it is no longer
used, sprd cyclic dma support, last batch of dma_slave_config
direction removal and random updates to bunch of drivers.
Summary:
- New driver for UniPhier MIO DMA controller
- Remove R-Mobile APE6 support
- Sprd driver updates and support for cyclic link-list
- Remove dma_slave_config direction usage from rest of drivers
- Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers"
* tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (48 commits)
dmaengine: qcom_hidma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: pxa: remove DBGFS_FUNC_DECL()
dmaengine: mic_x100_dma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: amba-pl08x: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: Documentation: Add documentation for multi chan testing
dmaengine: dmatest: Add transfer_size parameter
dmaengine: dmatest: Add alignment parameter
dmaengine: dmatest: Use fixed point div to calculate iops
dmaengine: dmatest: Add support for multi channel testing
dmaengine: rcar-dmac: Document R8A774C0 bindings
dt-bindings: dmaengine: usb-dmac: Add binding for r8a774c0
dmaengine: zynqmp_dma: replace spin_lock_bh with spin_lock_irqsave
dmaengine: sprd: Add me as one of the module authors
dmaengine: sprd: Support DMA 2-stage transfer mode
dmaengine: sprd: Support DMA link-list cyclic callback
dmaengine: sprd: Set cur_desc as NULL when free or terminate one dma channel
dmaengine: sprd: Fix the last link-list configuration
dmaengine: sprd: Get transfer residue depending on the transfer direction
dmaengine: sprd: Remove direction usage from struct dma_slave_config
dmaengine: dmatest: fix a small memory leak in dmatest_func()
...
Linus Torvalds [Tue, 1 Jan 2019 23:38:14 +0000 (15:38 -0800)]
Merge tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Mostly clean ups although while Doug's was chasing down a odd lockdep
warning he also did some work to improved debugger resilience when
some CPUs fail to respond to the round up request.
The main changes are:
- Fixing a lockdep warning on architectures that cannot use an NMI
for the round up plus related changes to make CPU round up and all
CPU backtrace more resilient.
- Constify the arch ops tables
- A couple of other small clean ups
Two of the three patchsets here include changes that spill over into
arch/. Changes in the arch space are relatively narrow in scope (and
directly related to kgdb). Didn't get comprehensive acks but all
impacted maintainers were Cc:ed in good time"
* tag 'kgdb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
kgdb/treewide: constify struct kgdb_arch arch_kgdb_ops
mips/kgdb: prepare arch_kgdb_ops for constness
kdb: use bool for binary state indicators
kdb: Don't back trace on a cpu that didn't round up
kgdb: Don't round up a CPU that failed rounding up before
kgdb: Fix kgdb_roundup_cpus() for arches who used smp_call_function()
kgdb: Remove irq flags from roundup
Linus Torvalds [Tue, 1 Jan 2019 21:24:31 +0000 (13:24 -0800)]
Merge tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
Linus Torvalds [Tue, 1 Jan 2019 21:19:16 +0000 (13:19 -0800)]
Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have no core changes but lots of incremental development in drivers
all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
keep churning out new SoCs.
I have some subtree maintainers for Renesas and Intel helping out to
keep down the load, it's been working smoothly (Samsung also have a
subtree but it was not used this cycle.)
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins with
another CPU using a hardware spinlock"
* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
pinctrl: imx-scu: Depend on IMX_SCU
pinctrl: ocelot: Add dependency on HAS_IOMEM
pinctrl: ocelot: add MSCC Jaguar2 support
pinctrl: bcm: ns: support updated DT binding as syscon subnode
dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
MAINTAINERS: merge at91 pinctrl entries
pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
pinctrl: uniphier: constify uniphier_pinctrl_socdata
pinctrl: mediatek: improve Kconfig dependencies
pinctrl: msm: mark PM functions as __maybe_unused
dt-bindings: pinctrl: sunxi: Add supply properties
pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
...
Linus Torvalds [Tue, 1 Jan 2019 21:16:45 +0000 (13:16 -0800)]
Merge tag 'linux-watchdog-4.21-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add TQ-Systems TQMX86 watchdog driver
- add Qualcomm PM8916 watchdog driver
- w83627hf_wdt: add quirk for Inves system
- renesas_wdt: several improvements and document r8a774c0 support
- mena21_wdt, mtx-1: Convert to use GPIO descriptor
- bcm281xx, ie6xx_wdt: convert to DEFINE_SHOW_ATTRIBUTE
- documentation: add PM usage and kernel-api: don't reference removed functions
- update bindings for MT7629 SoC
- several small fixes
* tag 'linux-watchdog-4.21-rc1' of git://www.linux-watchdog.org/linux-watchdog: (22 commits)
watchdog: tqmx86: Add watchdog driver for the IO controller
dt-bindings: watchdog: renesas-wdt: Document r8a774c0 support
watchdog: docs: kernel-api: don't reference removed functions
watchdog: add documentation for PM usage
watchdog: mtx-1: Convert to use GPIO descriptor
watchdog: mena21_wdt: Convert to GPIO descriptors
dt-bindings: watchdog: Add Qualcomm PM8916 watchdog
watchdog: Add pm8916 watchdog driver
dt-bindings: watchdog: update bindings for MT7629 SoC
watchdog: renesas_wdt: don't keep timer value during suspend/resume
watchdog: ie6xx_wdt: convert to DEFINE_SHOW_ATTRIBUTE
watchdog: bcm281xx: convert to DEFINE_SHOW_ATTRIBUTE
watchdog: asm9260_wdt: make array mode_name static, shrinks object size
watchdog/hpwdt: Update driver version.
watchdog/hpwdt: Do not claim unsupported hardware
watchdog/hpwdt: Exclude via blacklist
Watchdog: remove outdated comment
watchdog: w83627hf_wdt: Add quirk for Inves system
watchdog: cpwd: add of_node_put()
watchdog: renesas_wdt: don't set divider while watchdog is running
...
Eric Biggers [Sat, 3 Nov 2018 17:30:35 +0000 (10:30 -0700)]
KEYS: fix parsing invalid pkey info string
We need to check the return value of match_token() for Opt_err before
doing anything with it.
[ Not only did the old "-1" value for Opt_err cause problems for the
__test_and_set_bit(), as fixed in commit 94c13f66e13c ("security:
don't use a negative Opt_err token index"), but accessing
"args[0].from" is invalid for the Opt_err case, as pointed out by Eric
later. - Linus ]
Huazhong Tan [Mon, 31 Dec 2018 02:58:29 +0000 (10:58 +0800)]
net: hns3: call hns3_nic_net_open() while doing HNAE3_UP_CLIENT
For HNAE3_DOWN_CLIENT calling hns3_nic_net_stop(), HNAE3_UP_CLIENT
should call hns3_nic_net_open(), since if the number of queue or
the map of TC has is changed before HHAE3_UP_CLIENT is called,
it will cause problem.
Also the HNS3_NIC_STATE_RESETTING flag needs to be cleared before
hns3_nic_net_open() called, and set it back while hns3_nic_net_open()
failed.
Willem de Bruijn [Sun, 30 Dec 2018 22:24:36 +0000 (17:24 -0500)]
ip: validate header length on virtual device xmit
KMSAN detected read beyond end of buffer in vti and sit devices when
passing truncated packets with PF_PACKET. The issue affects additional
ip tunnel devices.
Extend commit 76c0ddd8c3a6 ("ip6_tunnel: be careful when accessing the
inner header") and commit ccfec9e5cb2d ("ip_tunnel: be careful when
accessing the inner header").
Move the check to a separate helper and call at the start of each
ndo_start_xmit function in net/ipv4 and net/ipv6.
Minor changes:
- convert dev_kfree_skb to kfree_skb on error path,
as dev_kfree_skb calls consume_skb which is not for error paths.
- use pskb_network_may_pull even though that is pedantic here,
as the same as pskb_may_pull for devices without llheaders.
- do not cache ipv6 hdrs if used only once
(unsafe across pskb_may_pull, was more relevant to earlier patch)
Willem de Bruijn [Sun, 30 Dec 2018 22:21:05 +0000 (17:21 -0500)]
tap: call skb_probe_transport_header after setting skb->dev
The BPF flow dissector expects either skb->sk or skb->dev set on
all skbs. Delay flow dissection until after skb->dev is set.
This requires calling from within an rcu read-side critical section.
That is fine, see also the call from tun_xdp_one.
Fixes: d0e13a1488ad ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL") Reported-by: Christian Borntraeger <[email protected]> Signed-off-by: Willem de Bruijn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Cong Wang [Sun, 30 Dec 2018 20:43:42 +0000 (12:43 -0800)]
ptr_ring: wrap back ->producer in __ptr_ring_swap_queue()
__ptr_ring_swap_queue() tries to move pointers from the old
ring to the new one, but it forgets to check if ->producer
is beyond the new size at the end of the operation. This leads
to an out-of-bound access in __ptr_ring_produce() as reported
by syzbot.
Takashi Iwai [Mon, 31 Dec 2018 18:02:01 +0000 (19:02 +0100)]
ALSA: hda - Revert DSP detection on legacy HD-audio driver
This essentially reverts the commits c337104b1a16 ("ALSA: HD-Audio: SKL+: abort probe if DSP is present
and Skylake driver selected")
and d82b51c855a2 ("ALSA: HD-Audio: SKL+: force HDaudio legacy or SKL+
driver selection")
for the path of legacy HD-audio controller (snd-hda-intel).
The automatic DSP detection and skip of binding with the legacy driver
caused regressions on several machines like Dell XPS13. They give the
PCI class 0x40380 indicating the availability of DSP while they don't
work with ASoC SKL driver (yet).
As the support of ASoC driver for such devices isn't available, it's
better to revert the whole DSP-detection-and-skip behavior of the
legacy driver, so that we can get the old good driver working on such
devices.
The pci_binding option for ASoC SKL driver is still kept so that it
can work without blacklisting.
Deepa Dinamani [Fri, 28 Dec 2018 02:55:09 +0000 (18:55 -0800)]
sock: Make sock->sk_stamp thread-safe
Al Viro mentioned (Message-ID
<20170626041334[email protected]>)
that there is probably a race condition
lurking in accesses of sk_stamp on 32-bit machines.
sock->sk_stamp is of type ktime_t which is always an s64.
On a 32 bit architecture, we might run into situations of
unsafe access as the access to the field becomes non atomic.
Use seqlocks for synchronization.
This allows us to avoid using spinlocks for readers as
readers do not need mutual exclusion.
Another approach to solve this is to require sk_lock for all
modifications of the timestamps. The current approach allows
for timestamps to have their own lock: sk_stamp_lock.
This allows for the patch to not compete with already
existing critical sections, and side effects are limited
to the paths in the patch.
The addition of the new field maintains the data locality
optimizations from
commit 9115e8cd2a0c ("net: reorganize struct sock for better data
locality")
Note that all the instances of the sk_stamp accesses
are either through the ioctl or the syscall recvmsg.
Sameer Pujar [Wed, 26 Dec 2018 10:34:49 +0000 (16:04 +0530)]
ALSA: hda/tegra: clear pending irq handlers
Even after disabling interrupts on the module, it could be possible
that irq handlers are still running. System hang is seen during
suspend path. It was found that, there were pending writes on the
HDA bus and clock was disabled by that time.
Above mentioned issue is fixed by clearing any pending irq handlers
before disabling clocks and returning from hda suspend.
Jian-Hong Pan [Thu, 27 Dec 2018 08:46:31 +0000 (16:46 +0800)]
ALSA: hda/realtek: Enable the headset mic auto detection for ASUS laptops
The headset mic of ASUS laptops like UX533FD, UX433FN and UX333FA, whose
CODEC is Realtek ALC294 has jack auto detection feature. This patch
enables the feature.
Theodore Ts'o [Tue, 1 Jan 2019 03:34:31 +0000 (22:34 -0500)]
ext4: fix special inode number checks in __ext4_iget()
The check for special (reserved) inode number checks in __ext4_iget()
was broken by commit 8a363970d1dc: ("ext4: avoid declaring fs
inconsistent due to invalid file handles"). This was caused by a
botched reversal of the sense of the flag now known as
EXT4_IGET_SPECIAL (when it was previously named EXT4_IGET_NORMAL).
Fix the logic appropriately.
Linus Torvalds [Tue, 1 Jan 2019 01:40:14 +0000 (17:40 -0800)]
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"Most changes here are to enable new drivers and platforms in the
various configs that affect them. Most of these have been covered and
described in the other branches, we mostly keep defconfig separate to
avoid conflicts between SoC/dt/driver updates that they otherwise
would be grouped with.
One thing worth mentioning here is that OMAP changes from using their
own UART driver, to 8250, for the multi_v7_defconfig shared config on
32-bit. This means that the console is now named ttyS* instead of
ttyO*. This change was already done for omap2_defconfig a while back,
so most users of these configs have either already updated, or can
easily follow the same patterns as they did at that time. This makes
platform support slightly easier for distros, since they no longer
need to keep track of a separate console prefix for these platforms"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
Revert "arm64: defconfig: Enable FSL_MC_BUS and FSL_MC_DPIO"
arm64: defconfig: Enable FSL_MC_BUS and FSL_MC_DPIO
arm64: defconfig: Replace PINCTRL_MT7622 with PINCTRL_MTK_MOORE
arm64: defconfig: Regenerate for v4.20
ARM: multi_v7_defconfig: Add TOSHIBA TC358764 bridge driver
ARM: multi_v7_defconfig: Add MAX8952 regulator driver
ARM: exynos_defconfig: Add TOSHIBA TC358764 bridge driver
ARM: exynos_defconfig: Add MAX8952 regulator driver
ARM: exynos_defconfig: Add MAX8998 RTC and charger drivers
ARM: imx_v6_v7_defconfig: add imx7ulp support
ARM: imx_v6_v7_defconfig: Select TOUCHSCREEN_GOODIX
ARM: multi_v7_defconfig: enable STM32 analog & timer drivers
arm64: defconfig: Enable GCC and PINCTRL for MSM8998
arm64: defconfig: Enable core Qualcomm SDM845 options
ARM: defconfig: Enable the PL111 DRM driver on vexpress
ARM: defconfig: Update the vexpress defconfig
arm64: defconfig: Enable some qcom remoteproc configs
arm64: defconfig: Enable QCS404 configs
ARM: imx_v6_v7_defconfig: Enable USB_ANNOUNCE_NEW_DEVICES
ARM: imx_v6_v7_defconfig: Enable BT_BNEP
...
Linus Torvalds [Tue, 1 Jan 2019 01:36:02 +0000 (17:36 -0800)]
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
Linus Torvalds [Tue, 1 Jan 2019 01:32:35 +0000 (17:32 -0800)]
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
Linus Torvalds [Tue, 1 Jan 2019 01:27:54 +0000 (17:27 -0800)]
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
Tyrel Datwyler [Mon, 31 Dec 2018 21:43:01 +0000 (15:43 -0600)]
ibmveth: fix DMA unmap error in ibmveth_xmit_start error path
Commit 33a48ab105a7 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec677 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec677 ("ibmveth: Add scatter-gather support") Signed-off-by: Tyrel Datwyler <[email protected]> Signed-off-by: David S. Miller <[email protected]>
The bcm2835-thermal driver was added with commit ac178e4280e6
("ARM64: bcm2835: add thermal driver to default config"). Unfortunately
this was accidentally dropped by commit eb1e6716cc9c
("arm64: defconfig: sync with savedefconfig"). So enable the driver again.
Fixes: eb1e6716cc9c ("arm64: defconfig: sync with savedefconfig") Signed-off-by: Stefan Wahren <[email protected]> Signed-off-by: Olof Johansson <[email protected]>
Olof Johansson [Mon, 31 Dec 2018 21:12:02 +0000 (13:12 -0800)]
Merge tag 'sti-soc-for-v4.21-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into next/late
Highlights:
-----------
- Following pen_release and boot_lock cleanup initiated by
Russell King, .smp_prepare_cpus and .smp_boot_secondary STi callbacks
must be reworked to keep secondary CPU's bringup.
* tag 'sti-soc-for-v4.21-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: sti: remove pen_release and boot_lock
Olof Johansson [Mon, 31 Dec 2018 21:10:16 +0000 (13:10 -0800)]
Merge tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Olof Johansson [Mon, 31 Dec 2018 21:07:11 +0000 (13:07 -0800)]
Merge tag 'imx8mq-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/late
i.MX8MQ device tree support for 4.21:
- It contains the initial device tree support for i.MX8MQ - the first
ARM64 i.MX processor. It features a quad Cortex-A53 core that
operates at speeds of up to 1.3 GHz, a Cortex-M4 core for
low-power processing, a DRAM controller that supports 32-bit/16-bit
LPDDR4/DDR4/DDR3L memory, and hardware acceleration for 4K video
playback.
- A couple of patches from Baruch that add watchdog device for i.MX8MQ
enable it for imx8mq-evk board.
* tag 'imx8mq-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
arm64: add basic Kconfig symbols for i.MX8
arm64: dts: ls1046a: add qdma device tree nodes
arm64: dts: ls1043a: add qdma device tree nodes
arm64: dts: ls1088a: Add missing dma-ranges property
arm64: dts: ls1088a: Move fsl-mc node
arm64: dts: fsl: Add all CPUs in cooling maps
arm64: dts: Add support for NXP LS1028A SoC
arm64: dts: layerscape: removed compatible string "snps,dw-pcie"
arm64: dts: fsl: Add the status property disable PCIe
arm64: dts: ls1012a: Add FRWY-LS1012A board support
dt-bindings: Add binding for i.MX8MQ CCM
arm64: dts: add LX2160AQDS board support
arm64: dts: add LX2160ARDB board support
arm64: dts: add QorIQ LX2160A SoC support
Linus Torvalds [Mon, 31 Dec 2018 19:46:59 +0000 (11:46 -0800)]
Merge tag 'trace-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Rework of the kprobe/uprobe and synthetic events to consolidate all
the dynamic event code. This will make changes in the future easier.
- Partial rewrite of the function graph tracing infrastructure. This
will allow for multiple users of hooking onto functions to get the
callback (return) of the function. This is the ground work for having
kprobes and function graph tracer using one code base.
- Clean up of the histogram code that will facilitate adding more
features to the histograms in the future.
- Addition of str_has_prefix() and a few use cases. There currently is
a similar function strstart() that is used in a few places, but only
returns a bool and not a length. These instances will be removed in
the future to use str_has_prefix() instead.
- A few other various clean ups as well.
* tag 'trace-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
tracing: Use the return of str_has_prefix() to remove open coded numbers
tracing: Have the historgram use the result of str_has_prefix() for len of prefix
tracing: Use str_has_prefix() instead of using fixed sizes
tracing: Use str_has_prefix() helper for histogram code
string.h: Add str_has_prefix() helper function
tracing: Make function ‘ftrace_exports’ static
tracing: Simplify printf'ing in seq_print_sym
tracing: Avoid -Wformat-nonliteral warning
tracing: Merge seq_print_sym_short() and seq_print_sym_offset()
tracing: Add hist trigger comments for variable-related fields
tracing: Remove hist trigger synth_var_refs
tracing: Use hist trigger's var_ref array to destroy var_refs
tracing: Remove open-coding of hist trigger var_ref management
tracing: Use var_refs[] for hist trigger reference checking
tracing: Change strlen to sizeof for hist trigger static strings
tracing: Remove unnecessary hist trigger struct field
tracing: Fix ftrace_graph_get_ret_stack() to use task and not current
seq_buf: Use size_t for len in seq_buf_puts()
seq_buf: Make seq_buf_puts() null-terminate the buffer
arm64: Use ftrace_graph_get_ret_stack() instead of curr_ret_stack
...
Linus Torvalds [Mon, 31 Dec 2018 17:57:14 +0000 (09:57 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha architecture updates from Matt Turner:
"A few small changes for alpha as well as the new system call table
generation support from Firoz Khan"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: Remove some unused variables
alpha: rtc: simplify alpha_rtc_init
alpha: Fix a typo on ptrace.h
alpha: fix spelling mistake QSD_PORT_ACTUVE -> QSD_PORT_ACTIVE
alpha: generate uapi header and syscall table header files
alpha: add system call table generation support
alpha: add __NR_syscalls along with NR_SYSCALLS
alpha: remove CONFIG_OSF4_COMPAT flag from syscall table
alpha: move __IGNORE* entries to non uapi header
Linus Torvalds [Mon, 31 Dec 2018 17:54:17 +0000 (09:54 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"This is a revert for a lockup in cgroups-intense workloads - the real
fixes will come later"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix infinite loop in update_blocked_averages() by reverting a9e7f6544b9c
Linus Torvalds [Mon, 31 Dec 2018 17:46:39 +0000 (09:46 -0800)]
Merge tag 'dax-fix-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull dax fix from Dan Williams:
"Clean up unnecessary usage of prepare_to_wait_exclusive().
While I feel a bit silly sending a single-commit pull-request there is
nothing else queued up for dax this cycle. This change has shipped in
-next for multiple releases"
* tag 'dax-fix-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: Use non-exclusive wait in wait_entry_unlocked()
Linus Torvalds [Mon, 31 Dec 2018 17:41:37 +0000 (09:41 -0800)]
Merge tag 'f2fs-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, we've focused on bug fixes since Pixel devices have
been shipping with f2fs. Some of them were related to hardware
encryption support which are actually not an issue in mainline, but
would be better to merge them in order to avoid potential bugs.
Enhancements:
- do GC sub-sections when the section is large
- add a flag in ioctl(SHUTDOWN) to trigger fsck for QA
- use kvmalloc() in order to give another chance to avoid ENOMEM
Bug fixes:
- fix accessing memory boundaries in a malformed iamge
- GC gives stale unencrypted block
- GC counts in large sections
- detect idle time more precisely
- block allocation of DIO writes
- race conditions between write_begin and write_checkpoint
- allow GCs for node segments via ioctl()
There are various clean-ups and minor bug fixes as well"
* tag 'f2fs-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (43 commits)
f2fs: sanity check of xattr entry size
f2fs: fix use-after-free issue when accessing sbi->stat_info
f2fs: check PageWriteback flag for ordered case
f2fs: fix validation of the block count in sanity_check_raw_super
f2fs: fix missing unlock(sbi->gc_mutex)
f2fs: fix to dirty inode synchronously
f2fs: clean up structure extent_node
f2fs: fix block address for __check_sit_bitmap
f2fs: fix sbi->extent_list corruption issue
f2fs: clean up checkpoint flow
f2fs: flush stale issued discard candidates
f2fs: correct wrong spelling, issing_*
f2fs: use kvmalloc, if kmalloc is failed
f2fs: remove redundant comment of unused wio_mutex
f2fs: fix to reorder set_page_dirty and wait_on_page_writeback
f2fs: clear PG_writeback if IPU failed
f2fs: add an ioctl() to explicitly trigger fsck later
f2fs: avoid frequent costly fsck triggers
f2fs: fix m_may_create to make OPU DIO write correctly
f2fs: fix to update new block address correctly for OPU
...
Reverting commit 8ccb8cb1892b ("swim3: convert to blk-mq") resolves the
problem.
That commit added a struct blk_mq_tag_set to struct floppy_state and
initialized it with a blk_mq_init_sq_queue() call. Unfortunately, there
is a memset() in swim3_add_device() that subsequently clears the
floppy_state struct. That means fs->tag_set->ops is a NULL pointer, and
it gets dereferenced by blk_mq_free_rqs() which gets called in the
request_irq() error path. Move the memset() to fix this bug.
BTW, the request_irq() failure for the left mediabay floppy (fd1) is not
a regression. I don't know why it happens. The right media bay floppy
(fd0) works fine however.
Finn Thain [Mon, 31 Dec 2018 05:44:09 +0000 (16:44 +1100)]
block/swim3: Fix -EBUSY error when re-opening device after unmount
When the block device is opened with FMODE_EXCL, ref_count is set to -1.
This value doesn't get reset when the device is closed which means the
device cannot be opened again. Fix this by checking for refcount <= 0
in the release method.
Vasily Averin [Sat, 29 Dec 2018 13:38:51 +0000 (16:38 +0300)]
nfs: fixed broken compilation in nfs_callback_up_net()
Patch fixes compilation error in nfs_callback_up_net()
serv->sv_bc_enabled is defined under enabled CONFIG_SUNRPC_BACKCHANNEL,
however nfs_callback_up_net() can access it even if this config option
was not set.
Fixes: a289ce5311f4 (sunrpc: replace svc_serv->sv_bc_xprt by boolean flag) Reported-by: kbuild test robot <[email protected]> Signed-off-by: Vasily Averin <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]>
Huacai Chen [Tue, 25 Dec 2018 00:51:01 +0000 (08:51 +0800)]
MIPS: Fix a R10000_LLSC_WAR logic in atomic.h
Commit 4936084c2ee2 ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
introduce a mistake in atomic64_fetch_##op##_relaxed(), because it
forget to delete R10000_LLSC_WAR in the if-condition. So fix it.
Guo Ren [Sun, 9 Dec 2018 09:31:53 +0000 (17:31 +0800)]
csky: remove unused members in processor.h
Cleanup struct cpuinfo_csky and struct thread_struct, remove all esp0
related code. We could get pt_regs from sp and backtrace could use fp
in switch_stack.
Jonas Gorski [Sun, 30 Dec 2018 11:55:09 +0000 (12:55 +0100)]
MIPS: BCM63XX: drop unused and broken DSP platform device
Trying to register the DSP platform device results in a null pointer
access:
[ 0.124184] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 804e305c, ra == 804e6f20
[ 0.135208] Oops[#1]:
[ 0.137514] CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.87
...
[ 0.197117] epc : 804e305c bcm63xx_dsp_register+0x80/0xa4
[ 0.202838] ra : 804e6f20 board_register_devices+0x258/0x390
...
This happens because it tries to copy the passed platform data over the
platform_device's unpopulated platform_data.
Since this code has been broken since its submission, no driver was ever
submitted for it, and apparently nobody was using it, just remove it
instead of trying to fix it.
Guo Ren [Mon, 31 Dec 2018 07:17:48 +0000 (15:17 +0800)]
csky: fixup save hi,lo,dspcr regs in switch_stack.
HI, LO, DSPCR registers are 807/810 related regs and no need for 610/860.
All of the regs must be saved in pt_regs and switch_stack. This patch
fixup saving dspcr reg in switch_stack and pt_regs.
Guo Ren [Sun, 30 Dec 2018 17:19:29 +0000 (01:19 +0800)]
csky: fixup remove vdsp implement for kernel.
The vr regs for vdsp only saved in task_switch not in every
exception trap-in. The memcpy with vdsp instructions will
destroy the vr regs for user space applications.
projects / linux.git / log