Linus Torvalds [Sun, 8 May 2022 19:42:05 +0000 (12:42 -0700)]
Merge tag 'for-5.18/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"Some reverts of existing patches, which were necessary because of boot
issues due to wrong CPU clock handling and cache issues which led to
userspace segfaults with 32bit kernels. Dave has a whole bunch of
upcoming cache fixes which I then plan to push in the next merge
window.
Other than that just small updates and fixes, e.g. defconfig updates,
spelling fixes, a clocksource fix, boot topology fixes and a fix for
/proc/cpuinfo output to satisfy lscpu"
* tag 'for-5.18/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
Revert "parisc: Increase parisc_cache_flush_threshold setting"
parisc: Mark cr16 clock unstable on all SMP machines
parisc: Fix typos in comments
parisc: Change MAX_ADDRESS to become unsigned long long
parisc: Merge model and model name into one line in /proc/cpuinfo
parisc: Re-enable GENERIC_CPU_DEVICES for !SMP
parisc: Update 32- and 64-bit defconfigs
parisc: Only list existing CPUs in cpu_possible_mask
Revert "parisc: Fix patch code locking and flushing"
Revert "parisc: Mark sched_clock unstable only if clocks are not syncronized"
Revert "parisc: Mark cr16 CPU clocksource unstable on all SMP machines"
Linus Torvalds [Sun, 8 May 2022 18:38:23 +0000 (11:38 -0700)]
Merge tag 'powerpc-5.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix the DWARF CFI in our VDSO time functions, allowing gdb to
backtrace through them correctly.
- Fix a buffer overflow in the papr_scm driver, only triggerable by
hypervisor input.
- A fix in the recently added QoS handling for VAS (used for
communicating with coprocessors).
Thanks to Alan Modra, Haren Myneni, Kajol Jain, and Segher Boessenkool.
* tag 'powerpc-5.18-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Fix buffer overflow issue with CONFIG_FORTIFY_SOURCE
powerpc/vdso: Fix incorrect CFI in gettimeofday.S
powerpc/pseries/vas: Use QoS credits from the userspace
Linus Torvalds [Sun, 8 May 2022 18:21:54 +0000 (11:21 -0700)]
Merge tag 'x86-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A fix and an email address update:
- Prevent FPU state corruption.
The condition in irq_fpu_usable() grants FPU usage when the FPU is
not used in the kernel. That's just wrong as it does not take the
fpregs_lock()'ed regions into account. If FPU usage happens within
such a region from interrupt context, then the FPU state gets
corrupted.
That's a long standing bug, which got unearthed by the recent
changes to the random code.
- Josh wants to use his kernel.org email address"
* tag 'x86-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Prevent FPU state corruption
MAINTAINERS: Update Josh Poimboeuf's email address
Linus Torvalds [Sun, 8 May 2022 18:18:11 +0000 (11:18 -0700)]
Merge tag 'timers-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A fix and an email address update:
- Mark the NMI safe time accessors notrace to prevent tracer
recursion when they are selected as trace clocks.
- John Stultz has a new email address"
* tag 'timers-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Mark NMI safe time accessors as notrace
MAINTAINERS: Update email address for John Stultz
Linus Torvalds [Sun, 8 May 2022 18:10:17 +0000 (11:10 -0700)]
Merge tag 'irq-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A fix for the threaded interrupt core.
A quick sequence of request/free_irq() can result in a hang because
the interrupt thread did not reach the thread function and got stopped
in the kthread core already. That leaves a state active counter
arround which makes a invocation of synchronized_irq() on that
interrupt hang forever.
Ensure that the thread reached the thread function in request_irq() to
prevent that"
* tag 'irq-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Synchronize interrupt thread startup
Helge Deller [Sun, 8 May 2022 16:25:00 +0000 (18:25 +0200)]
parisc: Mark cr16 clock unstable on all SMP machines
The cr16 interval timers are not synchronized across CPUs, even with just
one dual-core CPU. This becomes visible if the machines have a longer
uptime.
parisc: Change MAX_ADDRESS to become unsigned long long
Dave noticed that for the 32-bit kernel MAX_ADDRESS should be a ULL,
otherwise this define would become 0:
MAX_ADDRESS (1UL << MAX_ADDRBITS)
It has no real effect on the kernel.
parisc: Merge model and model name into one line in /proc/cpuinfo
The Linux tool "lscpu" shows the double amount of CPUs if we have
"model" and "model name" in two different lines in /proc/cpuinfo.
This change combines the model and the model name into one line.
In commit 62773112acc5 ("parisc: Switch from GENERIC_CPU_DEVICES to
GENERIC_ARCH_TOPOLOGY") GENERIC_CPU_DEVICES was unconditionally turned
off, but this triggers a warning in topology_add_dev(). Turning it back
on for the !SMP case avoids this warning.
Linus Torvalds [Sun, 8 May 2022 17:28:22 +0000 (10:28 -0700)]
Merge tag 'core-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull PASID fix from Thomas Gleixner:
"A single bugfix for the PASID management code, which freed the PASID
too early. The PASID needs to be tied to the mm lifetime, not to the
address space lifetime"
* tag 'core-urgent-2022-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm: Fix PASID use-after-free issue
Linus Torvalds [Sun, 8 May 2022 17:10:51 +0000 (10:10 -0700)]
Merge tag 'sound-5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became slightly larger as I've been off in the last weeks.
The majority of changes here is about ASoC, fixes for dmaengine
and for addressing issues reported by CI, as well as other
device-specific small fixes.
Also, fixes for FireWire core stack and the usual HD-audio quirks
are included"
* tag 'sound-5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ASoC: SOF: Fix NULL pointer exception in sof_pci_probe callback
ASoC: ops: Validate input values in snd_soc_put_volsw_range()
ASoC: dmaengine: Restore NULL prepare_slave_config() callback
ASoC: atmel: mchp-pdmc: set prepare_slave_config
ASoC: max98090: Generate notifications on changes for custom control
ASoC: max98090: Reject invalid values in custom control put()
ALSA: fireworks: fix wrong return count shorter than expected by 4 bytes
ALSA: hda/realtek: Add quirk for Yoga Duet 7 13ITL6 speakers
firewire: core: extend card->lock in fw_core_handle_bus_reset
firewire: remove check of list iterator against head past the loop body
firewire: fix potential uaf in outbound_phy_packet_callback()
ASoC: rt9120: Correct the reg 0x09 size to one byte
ALSA: hda/realtek: Enable mute/micmute LEDs support for HP Laptops
ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec
ASoC: meson: axg-card: Fix nonatomic links
ASoC: meson: axg-tdm-interface: Fix formatters in trigger"
ASoC: soc-ops: fix error handling
ASoC: meson: Fix event generation for G12A tohdmi mux
ASoC: meson: Fix event generation for AUI CODEC mux
ASoC: meson: Fix event generation for AUI ACODEC mux
...
Willy Tarreau [Sun, 8 May 2022 09:37:08 +0000 (11:37 +0200)]
ataflop: use a statically allocated error counters
This is the last driver making use of fd_request->error_count, which is
easy to get wrong as was shown in floppy.c. We don't need to keep it
there, it can be moved to the atari_floppy_struct instead, so let's do
this.
Willy Tarreau [Sun, 8 May 2022 09:37:07 +0000 (11:37 +0200)]
floppy: use a statically allocated error counter
Interrupt handler bad_flp_intr() may cause a UAF on the recently freed
request just to increment the error count. There's no point keeping
that one in the request anyway, and since the interrupt handler uses a
static pointer to the error which cannot be kept in sync with the
pending request, better make it use a static error counter that's reset
for each new request. This reset now happens when entering
redo_fd_request() for a new request via set_next_request().
One initial concern about a single error counter was that errors on one
floppy drive could be reported on another one, but this problem is not
real given that the driver uses a single drive at a time, as that
PC-compatible controllers also have this limitation by using shared
signals. As such the error count is always for the "current" drive.
Takashi Iwai [Sun, 8 May 2022 08:49:25 +0000 (10:49 +0200)]
Merge tag 'asoc-fix-v5.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.18
A larger collection of fixes than I'd like, mainly because mixer-test
is making it's way into the CI systems and turning up issues on a wider
range of systems. The most substantial thing though is a revert and an
alternative fix for a dmaengine issue where the fix caused disruption
for some other configurations, the core fix is backed out an a driver
specific thing done instead.
Trond Myklebust [Sat, 7 May 2022 17:53:59 +0000 (13:53 -0400)]
SUNRPC: Ensure that the gssproxy client can start in a connected state
Ensure that the gssproxy client connects to the server from the gssproxy
daemon process context so that the AF_LOCAL socket connection is done
using the correct path and namespaces.
Fixes: 1d658336b05f ("SUNRPC: Add RPC based upcall mechanism for RPCGSS auth") Cc: [email protected] Signed-off-by: Trond Myklebust <[email protected]>
Linus Torvalds [Sat, 7 May 2022 18:02:02 +0000 (11:02 -0700)]
Merge tag 'gpio-fixes-for-v5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix the bounds check for the 'gpio-reserved-ranges' device property
in gpiolib-of
- drop the assignment of the pwm base number in gpio-mvebu (this was
missed by the patch doing it globally for all pwm drivers)
- fix the fwnode assignment (use own fwnode, not the parent's one) for
the GPIO irqchip in gpio-visconti
- update the irq_stat field before checking the trigger field in
gpio-pca953x
- update GPIO entry in MAINTAINERS
* tag 'gpio-fixes-for-v5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: pca953x: fix irq_stat not updated when irq is disabled (irq_mask not set)
gpio: visconti: Fix fwnode of GPIO IRQ
MAINTAINERS: update the GPIO git tree entry
gpio: mvebu: drop pwm base assignment
gpiolib: of: fix bounds check for 'gpio-reserved-ranges'
Linus Torvalds [Sat, 7 May 2022 17:47:51 +0000 (10:47 -0700)]
Merge tag 'block-5.18-2022-05-06' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A single revert for a change that isn't needed in 5.18, and a small
series for s390/dasd"
* tag 'block-5.18-2022-05-06' of git://git.kernel.dk/linux-block:
s390/dasd: Use kzalloc instead of kmalloc/memset
s390/dasd: Fix read inconsistency for ESE DASD devices
s390/dasd: Fix read for ESE with blksize < 4k
s390/dasd: prevent double format of tracks for ESE devices
s390/dasd: fix data corruption for ESE devices
Revert "block: release rq qos structures for queue without disk"
fbdev: efifb: Fix a use-after-free due early fb_info cleanup
Commit d258d00fb9c7 ("fbdev: efifb: Cleanup fb_info in .fb_destroy rather
than .remove") attempted to fix a use-after-free error due driver freeing
the fb_info in the .remove handler instead of doing it in .fb_destroy.
But ironically that change introduced yet another use-after-free since the
fb_info was still used after the free.
This should fix for good by freeing the fb_info at the end of the handler.
Using min_t(int, ...) as a potential array index implies to the compiler
that negative offsets should be allowed. This is not the case, though.
Replace "int" with "unsigned int". Fixes the following warning exposed
under future CONFIG_FORTIFY_SOURCE improvements:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/rcupdate.h:29,
from include/linux/rculist.h:11,
from include/linux/pid.h:5,
from include/linux/sched.h:14,
from include/linux/delay.h:23,
from drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:35:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function 't4_get_raw_vpd_params':
include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 29 and size [2147483648, 4294967295] [-Warray-bounds]
46 | #define __underlying_memcpy __builtin_memcpy
| ^
include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy'
388 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk'
433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2796:9: note: in expansion of macro 'memcpy'
2796 | memcpy(p->id, vpd + id, min_t(int, id_len, ID_LEN));
| ^~~~~~
include/linux/fortify-string.h:46:33: warning: '__builtin_memcpy' pointer overflow between offset 0 and size [2147483648, 4294967295] [-Warray-bounds]
46 | #define __underlying_memcpy __builtin_memcpy
| ^
include/linux/fortify-string.h:388:9: note: in expansion of macro '__underlying_memcpy'
388 | __underlying_##op(p, q, __fortify_size); \
| ^~~~~~~~~~~~~
include/linux/fortify-string.h:433:26: note: in expansion of macro '__fortify_memcpy_chk'
433 | #define memcpy(p, q, s) __fortify_memcpy_chk(p, q, s, \
| ^~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:2798:9: note: in expansion of macro 'memcpy'
2798 | memcpy(p->sn, vpd + sn, min_t(int, sn_len, SERNUM_LEN));
| ^~~~~~
Additionally remove needless cast from u8[] to char * in last strim()
call.
Eric Dumazet [Thu, 5 May 2022 16:19:46 +0000 (09:19 -0700)]
netlink: do not reset transport header in netlink_recvmsg()
netlink_recvmsg() does not need to change transport header.
If transport header was needed, it should have been reset
by the producer (netlink_dump()), not the consumer(s).
The following trace probably happened when multiple threads
were using MSG_PEEK.
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
write to 0xffff88811e9f15b2 of 2 bytes by task 32012 on cpu 1:
skb_reset_transport_header include/linux/skbuff.h:2760 [inline]
netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
__sys_recvfrom+0x204/0x2c0 net/socket.c:2097
__do_sys_recvfrom net/socket.c:2115 [inline]
__se_sys_recvfrom net/socket.c:2111 [inline]
__x64_sys_recvfrom+0x74/0x90 net/socket.c:2111
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff88811e9f15b2 of 2 bytes by task 32005 on cpu 0:
skb_reset_transport_header include/linux/skbuff.h:2760 [inline]
netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978
____sys_recvmsg+0x162/0x2f0
___sys_recvmsg net/socket.c:2674 [inline]
__sys_recvmsg+0x209/0x3f0 net/socket.c:2704
__do_sys_recvmsg net/socket.c:2714 [inline]
__se_sys_recvmsg net/socket.c:2711 [inline]
__x64_sys_recvmsg+0x42/0x50 net/socket.c:2711
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff -> 0x0000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 32005 Comm: syz-executor.4 Not tainted 5.18.0-rc1-syzkaller-00328-ge1f700ebd6be-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
If successful ida_simple_get() calls are not undone when needed, some
additional memory may be allocated and wasted.
Here, an ID between 0 and MAX_INT is required. If this ID is >=100, it is
not taken into account and is wasted. It should be released.
Instead of calling ida_simple_remove(), take advantage of the 'max'
parameter to require the ID not to be too big. Should it be too big, it
is not allocated and don't need to be freed.
While at it, use ida_alloc_xxx()/ida_free() instead to
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.
Linus Torvalds [Fri, 6 May 2022 21:32:16 +0000 (14:32 -0700)]
Merge tag 'for-5.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Regression fixes in zone activation:
- move a loop invariant out of the loop to avoid checking space
status
- properly handle unlimited activation
Other fixes:
- for subpage, force the free space v2 mount to avoid a warning and
make it easy to switch a filesystem on different page size systems
- export sysfs status of exclusive operation 'balance paused', so the
user space tools can recognize it and allow adding a device with
paused balance
- fix assertion failure when logging directory key range item"
* tag 'for-5.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: sysfs: export the balance paused state of exclusive operation
btrfs: fix assertion failure when logging directory key range item
btrfs: zoned: activate block group properly on unlimited active zone device
btrfs: zoned: move non-changing condition check out of the loop
btrfs: force v2 space cache usage for subpage mount
Robin Murphy [Tue, 5 Apr 2022 14:21:34 +0000 (15:21 +0100)]
drm/nouveau/tegra: Stop using iommu_present()
Even if some IOMMU has registered itself on the platform "bus", that
doesn't necessarily mean it provides translation for the device we
care about. Replace iommu_present() with a more appropriate check.
Linus Torvalds [Fri, 6 May 2022 20:19:11 +0000 (13:19 -0700)]
Merge tag 'nfs-for-5.18-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client fixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix a socket leak when setting up an AF_LOCAL RPC client
- Ensure that knfsd connects to the gss-proxy daemon on setup
Bugfixes:
- Fix a refcount leak when migrating a task off an offlined transport
- Don't gratuitously invalidate inode attributes on delegation return
- Don't leak sockets in xs_local_connect()
- Ensure timely close of disconnected AF_LOCAL sockets"
* tag 'nfs-for-5.18-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
Revert "SUNRPC: attempt AF_LOCAL connect on setup"
SUNRPC: Ensure gss-proxy connects on setup
SUNRPC: Ensure timely close of disconnected AF_LOCAL sockets
SUNRPC: Don't leak sockets in xs_local_connect()
NFSv4: Don't invalidate inode attributes on delegation return
SUNRPC release the transport of a relocated task with an assigned transport
The metadata dst is leaked when ip_route_input_mc() updates the dst for
the skb. Commit f38a9eb1f77b ("dst: Metadata destinations") correctly
handled dropping the dst in ip_route_input_slow() but missed the
multicast case which is handled by ip_route_input_mc(). Drop the dst in
ip_route_input_mc() avoiding the leak.
Linus Torvalds [Fri, 6 May 2022 18:42:58 +0000 (11:42 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"x86:
- Account for family 17h event renumberings in AMD PMU emulation
- Remove CPUID leaf 0xA on AMD processors
- Fix lockdep issue with locking all vCPUs
- Fix loss of A/D bits in SPTEs
- Fix syzkaller issue with invalid guest state"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: Exit to userspace if vCPU has injected exception and invalid state
KVM: SEV: Mark nested locking of vcpu->lock
kvm: x86/cpuid: Only provide CPUID leaf 0xA if host has architectural PMU
KVM: x86/svm: Account for family 17h event renumberings in amd_pmc_perf_hw_id
KVM: x86/mmu: Use atomic XCHG to write TDP MMU SPTEs with volatile bits
KVM: x86/mmu: Move shadow-present check out of spte_has_volatile_bits()
KVM: x86/mmu: Don't treat fully writable SPTEs as volatile (modulo A/D)
Michal Michalik [Wed, 20 Apr 2022 12:23:02 +0000 (14:23 +0200)]
ice: fix PTP stale Tx timestamps cleanup
Read stale PTP Tx timestamps from PHY on cleanup.
After running out of Tx timestamps request handlers, hardware (HW) stops
reporting finished requests. Function ice_ptp_tx_tstamp_cleanup() used
to only clean up stale handlers in driver and was leaving the hardware
registers not read. Not reading stale PTP Tx timestamps prevents next
interrupts from arriving and makes timestamping unusable.
ice: clear stale Tx queue settings before configuring
The iAVF driver uses 3 virtchnl op codes to communicate with the PF
regarding the VF Tx queues:
* VIRTCHNL_OP_CONFIG_VSI_QUEUES configures the hardware and firmware
logic for the Tx queues
* VIRTCHNL_OP_ENABLE_QUEUES configures the queue interrupts
* VIRTCHNL_OP_DISABLE_QUEUES disables the queue interrupts and Tx rings.
There is a bug in the iAVF driver due to the race condition between VF
reset request and shutdown being executed in parallel. This leads to a
break in logic and VIRTCHNL_OP_DISABLE_QUEUES is not being sent.
If this occurs, the PF driver never cleans up the Tx queues. This results
in leaving behind stale Tx queue settings in the hardware and firmware.
The most obvious outcome is that upon the next
VIRTCHNL_OP_CONFIG_VSI_QUEUES, the PF will fail to program the Tx
scheduler node due to a lack of space.
We need to protect ICE driver against such situation.
To fix this, make sure we clear existing stale settings out when
handling VIRTCHNL_OP_CONFIG_VSI_QUEUES. This ensures we remove the
previous settings.
Calling ice_vf_vsi_dis_single_txq should be safe as it will do nothing if
the queue is not configured. The function already handles the case when the
Tx queue is not currently configured and exits with a 0 return in that
case.
Fixes: 7ad15440acf8 ("ice: Refactor VIRTCHNL_OP_CONFIG_VSI_QUEUES handling") Signed-off-by: Jacob Keller <[email protected]> Signed-off-by: Anatolii Gerasymenko <[email protected]> Tested-by: Konrad Jankowski <[email protected]> Signed-off-by: Tony Nguyen <[email protected]>
Ivan Vecera [Sat, 23 Apr 2022 10:20:21 +0000 (12:20 +0200)]
ice: Fix race during aux device (un)plugging
Function ice_plug_aux_dev() assigns pf->adev field too early prior
aux device initialization and on other side ice_unplug_aux_dev()
starts aux device deinit and at the end assigns NULL to pf->adev.
This is wrong because pf->adev should always be non-NULL only when
aux device is fully initialized and ready. This wrong order causes
a crash when ice_send_event_to_aux() call occurs because that function
depends on non-NULL value of pf->adev and does not assume that
aux device is half-initialized or half-destroyed.
After order correction the race window is tiny but it is still there,
as Leon mentioned and manipulation with pf->adev needs to be protected
by mutex.
Fix (un-)plugging functions so pf->adev field is set after aux device
init and prior aux device destroy and protect pf->adev assignment by
new mutex. This mutex is also held during ice_send_event_to_aux()
call to ensure that aux device is valid during that call.
Note that device lock used ice_send_event_to_aux() needs to be kept
to avoid race with aux drv unload.
Reproducer:
cycle=1
while :;do
echo "#### Cycle: $cycle"
ip link set ens7f0 mtu 9000
ip link add bond0 type bond mode 1 miimon 100
ip link set bond0 up
ifenslave bond0 ens7f0
ip link set bond0 mtu 9000
ethtool -L ens7f0 combined 1
ip link del bond0
ip link set ens7f0 mtu 1500
sleep 1
let cycle++
done
In short when the device is added/removed to/from bond the aux device
is unplugged/plugged. When MTU of the device is changed an event is
sent to aux device asynchronously. This can race with (un)plugging
operation and because pf->adev is set too early (plug) or too late
(unplug) the function ice_send_event_to_aux() can touch uninitialized
or destroyed fields. In the case of crash below pf->adev->dev.mutex.
Crash:
[ 53.372066] bond0: (slave ens7f0): making interface the new active one
[ 53.378622] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 53.386294] IPv6: ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready
[ 53.549104] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 54.118906] ice 0000:ca:00.0 ens7f0: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.233374] ice 0000:ca:00.1 ens7f1: Number of in use tx queues changed inval
idating tc mappings. Priority traffic classification disabled!
[ 54.248204] bond0: (slave ens7f0): Releasing backup interface
[ 54.253955] bond0: (slave ens7f1): making interface the new active one
[ 54.274875] bond0: (slave ens7f1): Releasing backup interface
[ 54.289153] bond0 (unregistering): Released all slaves
[ 55.383179] MII link monitoring set to 100 ms
[ 55.398696] bond0: (slave ens7f0): making interface the new active one
[ 55.405241] BUG: kernel NULL pointer dereference, address: 0000000000000080
[ 55.405289] bond0: (slave ens7f0): Enslaving as an active interface with an u
p link
[ 55.412198] #PF: supervisor write access in kernel mode
[ 55.412200] #PF: error_code(0x0002) - not-present page
[ 55.412201] PGD 25d2ad067 P4D 0
[ 55.412204] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 55.412207] CPU: 0 PID: 403 Comm: kworker/0:2 Kdump: loaded Tainted: G S 5.17.0-13579-g57f2d6540f03 #1
[ 55.429094] bond0: (slave ens7f1): Enslaving as a backup interface with an up
link
[ 55.430224] Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.4.4 10/07/
2021
[ 55.430226] Workqueue: ice ice_service_task [ice]
[ 55.468169] RIP: 0010:mutex_unlock+0x10/0x20
[ 55.472439] Code: 0f b1 13 74 96 eb e0 4c 89 ee eb d8 e8 79 54 ff ff 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 65 48 8b 04 25 40 ef 01 00 31 d2 <f0> 48 0f b1 17 75 01 c3 e9 e3 fe ff ff 0f 1f 00 0f 1f 44 00 00 48
[ 55.491186] RSP: 0018:ff4454230d7d7e28 EFLAGS: 00010246
[ 55.496413] RAX: ff1a79b208b08000 RBX: ff1a79b2182e8880 RCX: 0000000000000001
[ 55.503545] RDX: 0000000000000000 RSI: ff4454230d7d7db0 RDI: 0000000000000080
[ 55.510678] RBP: ff1a79d1c7e48b68 R08: ff4454230d7d7db0 R09: 0000000000000041
[ 55.517812] R10: 00000000000000a5 R11: 00000000000006e6 R12: ff1a79d1c7e48bc0
[ 55.524945] R13: 0000000000000000 R14: ff1a79d0ffc305c0 R15: 0000000000000000
[ 55.532076] FS: 0000000000000000(0000) GS:ff1a79d0ffc00000(0000) knlGS:0000000000000000
[ 55.540163] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 55.545908] CR2: 0000000000000080 CR3: 00000003487ae003 CR4: 0000000000771ef0
[ 55.553041] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 55.560173] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 55.567305] PKRU: 55555554
[ 55.570018] Call Trace:
[ 55.572474] <TASK>
[ 55.574579] ice_service_task+0xaab/0xef0 [ice]
[ 55.579130] process_one_work+0x1c5/0x390
[ 55.583141] ? process_one_work+0x390/0x390
[ 55.587326] worker_thread+0x30/0x360
[ 55.590994] ? process_one_work+0x390/0x390
[ 55.595180] kthread+0xe6/0x110
[ 55.598325] ? kthread_complete_and_exit+0x20/0x20
[ 55.603116] ret_from_fork+0x1f/0x30
[ 55.606698] </TASK>
KVM: VMX: Exit to userspace if vCPU has injected exception and invalid state
Exit to userspace with an emulation error if KVM encounters an injected
exception with invalid guest state, in addition to the existing check of
bailing if there's a pending exception (KVM doesn't support emulating
exceptions except when emulating real mode via vm86).
In theory, KVM should never get to such a situation as KVM is supposed to
exit to userspace before injecting an exception with invalid guest state.
But in practice, userspace can intervene and manually inject an exception
and/or stuff registers to force invalid guest state while a previously
injected exception is awaiting reinjection.
Peter Gonda [Mon, 2 May 2022 16:58:07 +0000 (09:58 -0700)]
KVM: SEV: Mark nested locking of vcpu->lock
svm_vm_migrate_from() uses sev_lock_vcpus_for_migration() to lock all
source and target vcpu->locks. Unfortunately there is an 8 subclass
limit, so a new subclass cannot be used for each vCPU. Instead maintain
ownership of the first vcpu's mutex.dep_map using a role specific
subclass: source vs target. Release the other vcpu's mutex.dep_maps.
Linus Torvalds [Fri, 6 May 2022 16:50:25 +0000 (09:50 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A few recent regressions in rxe's multicast code, and some old driver
bugs:
- Error case unwind bug in rxe for rkeys
- Dot not call netdev functions under a spinlock in rxe multicast
code
- Use the proper BH lock type in rxe multicast code
- Fix idrma deadlock and crash
- Add a missing flush to drain irdma QPs when in error
- Fix high userspace latency in irdma during destroy due to
synchronize_rcu()
- Rare race in siw MPA processing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/rxe: Change mcg_lock to a _bh lock
RDMA/rxe: Do not call dev_mc_add/del() under a spinlock
RDMA/siw: Fix a condition race issue in MPA request processing
RDMA/irdma: Fix possible crash due to NULL netdev in notifier
RDMA/irdma: Reduce iWARP QP destroy time
RDMA/irdma: Flush iWARP QP if modified to ERR from RTR state
RDMA/rxe: Recheck the MR in when generating a READ reply
RDMA/irdma: Fix deadlock in irdma_cleanup_cm_core()
RDMA/rxe: Fix "Replace mr by rkey in responder resources"
Linus Torvalds [Fri, 6 May 2022 16:33:28 +0000 (09:33 -0700)]
Merge tag 'drm-fixes-2022-05-06' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"A pretty quiet week, one fbdev, msm, kconfig, and two amdgpu fixes,
about what I'd expect for rc6.
fbdev:
- hotunplugging fix
amdgpu:
- Fix a xen dom0 regression on APUs
- Fix a potential array overflow if a receiver were to send an
erroneous audio channel count
msm:
- lockdep fix.
it6505:
- kconfig fix"
* tag 'drm-fixes-2022-05-06' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Avoid reading audio pattern past AUDIO_CHANNELS_COUNT
drm/amdgpu: do not use passthrough mode in Xen dom0
drm/bridge: ite-it6505: add missing Kconfig option select
fbdev: Make fb_release() return -ENODEV if fbdev was unregistered
drm/msm/dp: remove fail safe mode related code
Puyou Lu [Fri, 6 May 2022 08:06:30 +0000 (16:06 +0800)]
gpio: pca953x: fix irq_stat not updated when irq is disabled (irq_mask not set)
When one port's input state get inverted (eg. from low to hight) after
pca953x_irq_setup but before setting irq_mask (by some other driver such as
"gpio-keys"), the next inversion of this port (eg. from hight to low) will not
be triggered any more (because irq_stat is not updated at the first time). Issue
should be fixed after this commit.
Richard Gong [Fri, 8 Apr 2022 17:08:38 +0000 (12:08 -0500)]
drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems
Active State Power Management (ASPM) feature is enabled since kernel 5.14.
There are some AMD Volcanic Islands (VI) GFX cards, such as the WX3200 and
RX640, that do not work with ASPM-enabled Intel Alder Lake based systems.
Using these GFX cards as video/display output, Intel Alder Lake based
systems will freeze after suspend/resume.
The issue was originally reported on one system (Dell Precision 3660 with
BIOS version 0.14.81), but was later confirmed to affect at least 4
pre-production Alder Lake based systems.
Add an extra check to disable ASPM on Intel Alder Lake based systems with
the problematic AMD Volcanic Islands GFX cards.
Maximilian Luz [Fri, 29 Apr 2022 19:57:38 +0000 (21:57 +0200)]
platform/surface: aggregator: Fix initialization order when compiling as builtin module
When building the Surface Aggregator Module (SAM) core, registry, and
other SAM client drivers as builtin modules (=y), proper initialization
order is not guaranteed. Due to this, client driver registration
(triggered by device registration in the registry) races against bus
initialization in the core.
If any attempt is made at registering the device driver before the bus
has been initialized (i.e. if bus initialization fails this race) driver
registration will fail with a message similar to:
Driver surface_battery was unable to register with bus_type surface_aggregator because the bus was not initialized
Switch from module_init() to subsys_initcall() to resolve this issue.
Note that the serdev subsystem uses postcore_initcall() so we are still
able to safely register the serdev device driver for the core.
Maximilian Luz [Fri, 29 Apr 2022 18:00:49 +0000 (20:00 +0200)]
platform/surface: gpe: Add support for Surface Pro 8
The new Surface Pro 8 uses GPEs for lid events as well. Add an entry for
that so that the lid can be used to wake the device. Note that this is a
device with a keyboard type-cover, where this acts as the "lid".
The probe function, pmt_telem_probe(), adds an entry for devices even if
they have not been initialized. This results in the array of initialized
devices containing both initialized and uninitialized entries. This
causes a panic in the remove function, pmt_telem_remove() which expects
the array to only contain initialized entries.
platform/x86: thinkpad_acpi: Add a s2idle resume quirk for a number of laptops
Lenovo laptops that contain NVME SSDs across a variety of generations have
trouble resuming from suspend to idle when the IOMMU translation layer is
active for the NVME storage device.
This generally manifests as a large resume delay or page faults. These
delays and page faults occur as a result of a Lenovo BIOS specific SMI
that runs during the D3->D0 transition on NVME devices.
This SMI occurs because of a flag that is set during resume by Lenovo
firmware:
Create a quirk that will run early in the resume process to prevent this
SMI from running. As any of these machines are fixed, they can be peeled
back from this quirk or narrowed down to individual firmware versions.
Randy Dunlap [Sat, 30 Apr 2022 05:01:23 +0000 (22:01 -0700)]
KVM: arm64: nvhe: Eliminate kernel-doc warnings
Don't use begin-kernel-doc notation (/**) for comments that are not in
kernel-doc format.
This prevents these kernel-doc warnings:
arch/arm64/kvm/hyp/nvhe/switch.c:126: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Disable host events, enable guest events
arch/arm64/kvm/hyp/nvhe/switch.c:146: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Disable guest events, enable host events
arch/arm64/kvm/hyp/nvhe/switch.c:164: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Handler for protected VM restricted exceptions.
arch/arm64/kvm/hyp/nvhe/switch.c:176: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Handler for protected VM MSR, MRS or System instruction execution in AArch64.
arch/arm64/kvm/hyp/nvhe/switch.c:196: warning: Function parameter or member 'vcpu' not described in 'kvm_handle_pvm_fpsimd'
arch/arm64/kvm/hyp/nvhe/switch.c:196: warning: Function parameter or member 'exit_code' not described in 'kvm_handle_pvm_fpsimd'
arch/arm64/kvm/hyp/nvhe/switch.c:196: warning: expecting prototype for Handler for protected floating(). Prototype was for kvm_handle_pvm_fpsimd() instead
KVM: arm64: Avoid unnecessary absolute addressing via literals
There are a few cases in the nVHE code where we take the absolute
address of a symbol via a literal pool entry, and subsequently translate
it to another address space (PA, kimg VA, kernel linear VA, etc).
Originally, this literal was needed because we relied on a different
translation for absolute references, but this is no longer the case, so
we can simply use relative addressing instead. This removes a couple of
RELA entries pointing into the .text segment.
firmware_loader: use kernel credentials when reading firmware
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Previously, Android configurations were not setting up the
firmware_class.path command line argument and were relying on the
userspace fallback mechanism. In this case, the security context of the
userspace daemon (i.e. ueventd) was consistently used to read firmware
files. More Android devices are now found to set firmware_class.path
which gives the kernel the opportunity to read the firmware directly
(via kernel_read_file_from_path_initns). In this scenario, the current
process credentials were used, even if unrelated to the loading of the
firmware file.
fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
The driver is calling framebuffer_release() in its .remove callback, but
this will cause the struct fb_info to be freed too early. Since it could
be that a reference is still hold to it if user-space opened the fbdev.
This would lead to a use-after-free error if the framebuffer device was
unregistered but later a user-space process tries to close the fbdev fd.
To prevent this, move the framebuffer_release() call to fb_ops.fb_destroy
instead of doing it in the driver's .remove callback.
Strictly speaking, the code flow in the driver is still wrong because all
the hardware cleanupd (i.e: iounmap) should be done in .remove while the
software cleanup (i.e: releasing the framebuffer) should be done in the
.fb_destroy handler. But this at least makes to match the behavior before
commit 27599aacbaef ("fbdev: Hot-unplug firmware fb devices on forced removal").
fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
The driver is calling framebuffer_release() in its .remove callback, but
this will cause the struct fb_info to be freed too early. Since it could
be that a reference is still hold to it if user-space opened the fbdev.
This would lead to a use-after-free error if the framebuffer device was
unregistered but later a user-space process tries to close the fbdev fd.
To prevent this, move the framebuffer_release() call to fb_ops.fb_destroy
instead of doing it in the driver's .remove callback.
Strictly speaking, the code flow in the driver is still wrong because all
the hardware cleanupd (i.e: iounmap) should be done in .remove while the
software cleanup (i.e: releasing the framebuffer) should be done in the
.fb_destroy handler. But this at least makes to match the behavior before
commit 27599aacbaef ("fbdev: Hot-unplug firmware fb devices on forced removal").
fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
The driver is calling framebuffer_release() in its .remove callback, but
this will cause the struct fb_info to be freed too early. Since it could
be that a reference is still hold to it if user-space opened the fbdev.
This would lead to a use-after-free error if the framebuffer device was
unregistered but later a user-space process tries to close the fbdev fd.
To prevent this, move the framebuffer_release() call to fb_ops.fb_destroy
instead of doing it in the driver's .remove callback.
Strictly speaking, the code flow in the driver is still wrong because all
the hardware cleanupd (i.e: iounmap) should be done in .remove while the
software cleanup (i.e: releasing the framebuffer) should be done in the
.fb_destroy handler. But this at least makes to match the behavior before
commit 27599aacbaef ("fbdev: Hot-unplug firmware fb devices on forced removal").
Daniel Vetter [Thu, 5 May 2022 22:04:13 +0000 (00:04 +0200)]
fbdev: Prevent possible use-after-free in fb_release()
Most fbdev drivers have issues with the fb_info lifetime, because call to
framebuffer_release() from their driver's .remove callback, rather than
doing from fbops.fb_destroy callback.
Doing that will destroy the fb_info too early, while references to it may
still exist, leading to a use-after-free error.
To prevent this, check the fb_info reference counter when attempting to
kfree the data structure in framebuffer_release(). That will leak it but
at least will prevent the mentioned error.
Revert "fbdev: Make fb_release() return -ENODEV if fbdev was unregistered"
This reverts commit aafa025c76dcc7d1a8c8f0bdefcbe4eb480b2f6a. That commit
attempted to fix a NULL pointer dereference, caused by the struct fb_info
associated with a framebuffer device to not longer be valid when the file
descriptor was closed.
The issue was exposed by commit 27599aacbaef ("fbdev: Hot-unplug firmware
fb devices on forced removal"), which added a new path that goes through
the struct device removal instead of directly unregistering the fb.
Most fbdev drivers have issues with the fb_info lifetime, because call to
framebuffer_release() from their driver's .remove callback, rather than
doing from fbops.fb_destroy callback. This meant that due to this switch,
the fb_info was now destroyed too early, while references still existed,
while before it was simply leaked.
The patch we're reverting here reinstated that leak, hence "fixed" the
regression. But the proper solution is to fix the drivers to not release
the fb_info too soon.
Kajol Jain [Thu, 5 May 2022 15:34:51 +0000 (21:04 +0530)]
powerpc/papr_scm: Fix buffer overflow issue with CONFIG_FORTIFY_SOURCE
With CONFIG_FORTIFY_SOURCE enabled, string functions will also perform
dynamic checks for string size which can panic the kernel, like incase
of overflow detection.
In papr_scm, papr_scm_pmu_check_events function uses stat->stat_id with
string operations, to populate the nvdimm_events_map array. Since
stat_id variable is not NULL terminated, the kernel panics with
CONFIG_FORTIFY_SOURCE enabled at boot time.
Below are the logs of kernel panic:
detected buffer overflow in __fortify_strlen
------------[ cut here ]------------
kernel BUG at lib/string_helpers.c:980!
Oops: Exception in kernel mode, sig: 5 [#1]
NIP [c00000000077dad0] fortify_panic+0x28/0x38
LR [c00000000077dacc] fortify_panic+0x24/0x38
Call Trace:
[c0000022d77836e0] [c00000000077dacc] fortify_panic+0x24/0x38 (unreliable)
[c00800000deb2660] papr_scm_pmu_check_events.constprop.0+0x118/0x220 [papr_scm]
[c00800000deb2cb0] papr_scm_probe+0x288/0x62c [papr_scm]
[c0000000009b46a8] platform_probe+0x98/0x150
Fix this issue by using kmemdup_nul() to copy the content of
stat->stat_id directly to the nvdimm_events_map array.
mpe: stat->stat_id comes from the hypervisor, not userspace, so there is
no security exposure.
Jakub Kicinski [Fri, 6 May 2022 02:15:20 +0000 (19:15 -0700)]
Merge branch 'ocelot-vcap-fixes'
Vladimir Oltean says:
====================
Ocelot VCAP fixes
Changes in v2:
fix the NPDs and UAFs caused by filter->trap_list in a more robust way
that actually does not introduce bugs of its own (1/5)
This series fixes issues found while running
tools/testing/selftests/net/forwarding/tc_actions.sh on the ocelot
switch:
- NULL pointer dereference when failing to offload a filter
- NULL pointer dereference after deleting a trap
- filters still having effect after being deleted
- dropped packets still being seen by software
- statistics counters showing double the amount of hits
- statistics counters showing inexistent hits
- invalid configurations not rejected
====================
(1) we add filter A using tc-flower
(2) we send a packet that matches it
(3) we read the filter's statistics to find a hit count of 1
(4) we add a second filter B with a higher preference than A, and A
moves one position to the right to make room in the TCAM for it
(5) we send another packet, and this matches the second filter B
(6) we read the filter statistics again.
When this happens, the hit count of filter A is 2 and of filter B is 1,
despite a single packet having matched each filter.
Furthermore, in an alternate history, reading the filter stats a second
time between steps (3) and (4) makes the hit count of filter A remain at
1 after step (6), as expected.
The reason why this happens has to do with the filter->stats.pkts field,
which is written to hardware through the call path below:
The primary role of filter->stats.pkts is to transport the filter hit
counters from the last readout all the way from vcap_entry_get() ->
ocelot_vcap_filter_stats_update() -> ocelot_cls_flower_stats().
The reason why vcap_entry_set() writes it to hardware is so that the
counters (saturating and having a limited bit width) are cleared
after each user space readout.
The writing of filter->stats.pkts to hardware during the TCAM entry
movement procedure is an unintentional consequence of the code design,
because the hit count isn't up to date at this point.
So at step (4), when filter A is moved by ocelot_vcap_filter_add() to
make room for filter B, the hardware hit count is 0 (no packet matched
on it in the meantime), but filter->stats.pkts is 1, because the last
readout saw the earlier packet. The movement procedure programs the old
hit count back to hardware, so this creates the impression to user space
that more packets have been matched than they really were.
The bug can be seen when running the gact_drop_and_ok_test() from the
tc_actions.sh selftest.
Fix the issue by reading back the hit count to tmp->stats.pkts before
migrating the VCAP filter. Sure, this is a best-effort technique, since
the packets that hit the rule between vcap_entry_get() and
vcap_entry_set() won't be counted, but at least it allows the counters
to be reliably used for selftests where the traffic is under control.
The vcap_entry_get() name is a bit unintuitive, but it only reads back
the counter portion of the TCAM entry, not the entire entry.
The index from which we retrieve the counter is also a bit unintuitive
(i - 1 during add, i + 1 during del), but this is the way in which TCAM
entry movement works. The "entry index" isn't a stored integer for a
TCAM filter, instead it is dynamically computed by
ocelot_vcap_block_get_filter_index() based on the entry's position in
the &block->rules list. That position (as well as block->count) is
automatically updated by ocelot_vcap_filter_add_to_block() on add, and
by ocelot_vcap_block_remove_filter() on del. So "i" is the new filter
index, and "i - 1" or "i + 1" respectively are the old addresses of that
TCAM entry (we only support installing/deleting one filter at a time).
Fixes: b596229448dd ("net: mscc: ocelot: Add support for tcam") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Once the CPU port was added to the destination port mask of a packet, it
can never be cleared, so even packets marked as dropped by the MASK_MODE
of a VCAP IS2 filter will still reach it. This is why we need the
OCELOT_POLICER_DISCARD to "kill dropped packets dead" and make software
stop seeing them.
We disallow policer rules from being put on any other chain than the one
for the first lookup, but we don't do this for "drop" rules, although we
should. This change is merely ascertaining that the rules dont't
(completely) work and letting the user know.
The blamed commit is the one that introduced the multi-chain architecture
in ocelot. Prior to that, we should have always offloaded the filters to
VCAP IS2 lookup 0, where they did work.
Fixes: 1397a2eb52e2 ("net: mscc: ocelot: create TCAM skeleton from tc filter chains") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Vladimir Oltean [Wed, 4 May 2022 23:55:01 +0000 (02:55 +0300)]
net: mscc: ocelot: fix VCAP IS2 filters matching on both lookups
The VCAP IS2 TCAM is looked up twice per packet, and each filter can be
configured to only match during the first, second lookup, or both, or
none.
The blamed commit wrote the code for making VCAP IS2 filters match only
on the given lookup. But right below that code, there was another line
that explicitly made the lookup a "don't care", and this is overwriting
the lookup we've selected. So the code had no effect.
Some of the more noticeable effects of having filters match on both
lookups:
- in "tc -s filter show dev swp0 ingress", we see each packet matching a
VCAP IS2 filter counted twice. This throws off scripts such as
tools/testing/selftests/net/forwarding/tc_actions.sh and makes them
fail.
- a "tc-drop" action offloaded to VCAP IS2 needs a policer as well,
because once the CPU port becomes a member of the destination port
mask of a packet, nothing removes it, not even a PERMIT/DENY mask mode
with a port mask of 0. But VCAP IS2 rules with the POLICE_ENA bit in
the action vector can only appear in the first lookup. What happens
when a filter matches both lookups is that the action vector is
combined, and this makes the POLICE_ENA bit ineffective, since the
last lookup in which it has appeared is the second one. In other
words, "tc-drop" actions do not drop packets for the CPU port, dropped
packets are still seen by software unless there was an FDB entry that
directed those packets to some other place different from the CPU.
The last bit used to work, because in the initial commit b596229448dd
("net: mscc: ocelot: Add support for tcam"), we were writing the FIRST
field of the VCAP IS2 half key with a 1, not with a "don't care".
The change to "don't care" was made inadvertently by me in commit c1c3993edb7c ("net: mscc: ocelot: generalize existing code for VCAP"),
which I just realized, and which needs a separate fix from this one,
for "stable" kernels that lack the commit blamed below.
Fixes: 226e9cd82a96 ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Vladimir Oltean [Wed, 4 May 2022 23:55:00 +0000 (02:55 +0300)]
net: mscc: ocelot: fix last VCAP IS1/IS2 filter persisting in hardware when deleted
ocelot_vcap_filter_del() works by moving the next filters over the
current one, and then deleting the last filter by calling vcap_entry_set()
with a del_filter which was specially created by memsetting its memory
to zeroes. vcap_entry_set() then programs this to the TCAM and action
RAM via the cache registers.
The problem is that vcap_entry_set() is a dispatch function which looks
at del_filter->block_id. But since del_filter is zeroized memory, the
block_id is 0, or otherwise said, VCAP_ES0. So practically, what we do
is delete the entry at the same TCAM index from VCAP ES0 instead of IS1
or IS2.
The code was not always like this. vcap_entry_set() used to simply be
is2_entry_set(), and then, the logic used to work.
Restore the functionality by populating the block_id of the del_filter
based on the VCAP block of the filter that we're deleting. This makes
vcap_entry_set() know what to do.
Fixes: 1397a2eb52e2 ("net: mscc: ocelot: create TCAM skeleton from tc filter chains") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Vladimir Oltean [Wed, 4 May 2022 23:54:59 +0000 (02:54 +0300)]
net: mscc: ocelot: mark traps with a bool instead of keeping them in a list
Since the blamed commit, VCAP filters can appear on more than one list.
If their action is "trap", they are chained on ocelot->traps via
filter->trap_list. This is in addition to their normal placement on the
VCAP block->rules list head.
Therefore, when we free a VCAP filter, we must remove it from all lists
it is a member of, including ocelot->traps.
There are at least 2 bugs which are direct consequences of this design
decision.
First is the incorrect usage of list_empty(), meant to denote whether
"filter" is chained into ocelot->traps via filter->trap_list.
This does not do the correct thing, because list_empty() checks whether
"head->next == head", but in our case, head->next == head->prev == NULL.
So we dereference NULL pointers and die when we call list_del().
Second is the fact that not all places that should remove the filter
from ocelot->traps do so. One example is ocelot_vcap_block_remove_filter(),
which is where we have the main kfree(filter). By keeping freed filters
in ocelot->traps we end up in a use-after-free in
felix_update_trapping_destinations().
Attempting to fix all the buggy patterns is a whack-a-mole game which
makes the driver unmaintainable. Actually this is what the previous
patch version attempted to do:
https://patchwork.kernel.org/project/netdevbpf/patch/20220503115728[email protected]/
but it introduced another set of bugs, because there are other places in
which create VCAP filters, not just ocelot_vcap_filter_create():
Relying on the convention that all those code paths must call
INIT_LIST_HEAD(&filter->trap_list) is not going to scale.
So let's do what should have been done in the first place and keep a
bool in struct ocelot_vcap_filter which denotes whether we are looking
at a trapping rule or not. Iterating now happens over the main VCAP IS2
block->rules. The advantage is that we no longer risk having stale
references to a freed filter, since it is only present in that list.
Fixes: e42bd4ed09aa ("net: mscc: ocelot: keep traps in a list") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Jan Höppner [Thu, 5 May 2022 14:17:32 +0000 (16:17 +0200)]
s390/dasd: Fix read inconsistency for ESE DASD devices
Read requests that return with NRF error are partially completed in
dasd_eckd_ese_read(). The function keeps track of the amount of
processed bytes and the driver will eventually return this information
back to the block layer for further processing via __dasd_cleanup_cqr()
when the request is in the final stage of processing (from the driver's
perspective).
For this, blk_update_request() is used which requires the number of
bytes to complete the request. As per documentation the nr_bytes
parameter is described as follows:
"number of bytes to complete for @req".
This was mistakenly interpreted as "number of bytes _left_ for @req"
leading to new requests with incorrect data length. The consequence are
inconsistent and completely wrong read requests as data from random
memory areas are read back.
Fix this by correctly specifying the amount of bytes that should be used
to complete the request.
Jan Höppner [Thu, 5 May 2022 14:17:31 +0000 (16:17 +0200)]
s390/dasd: Fix read for ESE with blksize < 4k
When reading unformatted tracks on ESE devices, the corresponding memory
areas are simply set to zero for each segment. This is done incorrectly
for blocksizes < 4096.
There are two problems. First, the increment of dst is done using the
counter of the loop (off), which is increased by blksize every
iteration. This leads to a much bigger increment for dst as actually
intended. Second, the increment of dst is done before the memory area
is set to 0, skipping a significant amount of bytes of memory.
This leads to illegal overwriting of memory and ultimately to a kernel
panic.
This is not a problem with 4k blocksize because
blk_queue_max_segment_size is set to PAGE_SIZE, always resulting in a
single iteration for the inner segment loop (bv.bv_len == blksize). The
incorrectly used 'off' value to increment dst is 0 and the correct
memory area is used.
In order to fix this for blksize < 4k, increment dst correctly using the
blksize and only do it at the end of the loop.
s390/dasd: prevent double format of tracks for ESE devices
For ESE devices we get an error for write operations on an unformatted
track. Afterwards the track will be formatted and the IO operation
restarted.
When using alias devices a track might be accessed by multiple requests
simultaneously and there is a race window that a track gets formatted
twice resulting in data loss.
Prevent this by remembering the amount of formatted tracks when starting
a request and comparing this number before actually formatting a track
on the fly. If the number has changed there is a chance that the current
track was finally formatted in between. As a result do not format the
track and restart the current IO to check.
The number of formatted tracks does not match the overall number of
formatted tracks on the device and it might wrap around but this is no
problem. It is only needed to recognize that a track has been formatted at
all in between.
For ESE devices we get an error when accessing an unformatted track.
The handling of this error will return zero data for read requests and
format the track on demand before writing to it. To do this the code needs
to distinguish between read and write requests. This is done with data from
the blocklayer request. A pointer to the blocklayer request is stored in
the CQR.
If there is an error on the device an ERP request is built to do error
recovery. While the ERP request is mostly a copy of the original CQR the
pointer to the blocklayer request is not copied to not accidentally pass
it back to the blocklayer without cleanup.
This leads to the error that during ESE handling after an ERP request was
built it is not possible to determine the IO direction. This leads to the
formatting of a track for read requests which might in turn lead to data
corruption.
MAINTAINERS: add missing files for bonding definition
The bonding entry did not include additional include files that have
been added nor did it reference the documentation. Add these references
for completeness.
Tariq Toukan [Wed, 4 May 2022 08:09:14 +0000 (11:09 +0300)]
net: Fix features skip in for_each_netdev_feature()
The find_next_netdev_feature() macro gets the "remaining length",
not bit index.
Passing "bit - 1" for the following iteration is wrong as it skips
the adjacent bit. Pass "bit" instead.
Nicolas Dichtel [Wed, 4 May 2022 09:07:39 +0000 (11:07 +0200)]
selftests: add ping test with ping_group_range tuned
The 'ping' utility is able to manage two kind of sockets (raw or icmp),
depending on the sysctl ping_group_range. By default, ping_group_range is
set to '1 0', which forces ping to use an ip raw socket.
Let's replay the ping tests by allowing 'ping' to use the ip icmp socket.
After the previous patch, ipv4 tests results are the same with both kinds
of socket. For ipv6, there are a lot a new failures (the previous patch
fixes only two cases).
Nicolas Dichtel [Wed, 4 May 2022 09:07:38 +0000 (11:07 +0200)]
ping: fix address binding wrt vrf
When ping_group_range is updated, 'ping' uses the DGRAM ICMP socket,
instead of an IP raw socket. In this case, 'ping' is unable to bind its
socket to a local address owned by a vrflite.
Before the patch:
$ sysctl -w net.ipv4.ping_group_range='0 2147483647'
$ ip link add blue type vrf table 10
$ ip link add foo type dummy
$ ip link set foo master blue
$ ip link set foo up
$ ip addr add 192.168.1.1/24 dev foo
$ ip addr add 2001::1/64 dev foo
$ ip vrf exec blue ping -c1 -I 192.168.1.1 192.168.1.2
ping: bind: Cannot assign requested address
$ ip vrf exec blue ping6 -c1 -I 2001::1 2001::2
ping6: bind icmp socket: Cannot assign requested address
Fabio Estevam [Wed, 4 May 2022 14:31:03 +0000 (11:31 -0300)]
net: phy: micrel: Do not use kszphy_suspend/resume for KSZ8061
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the following
NULL pointer dereference is observed on a board with KSZ8061:
# udhcpc -i eth0
udhcpc: started, v1.35.0
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = f73cef4e
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 196 Comm: ifconfig Not tainted 5.15.37-dirty #94
Hardware name: Freescale i.MX6 SoloX (Device Tree)
PC is at kszphy_config_reset+0x10/0x114
LR is at kszphy_resume+0x24/0x64
...
The KSZ8061 phy_driver structure does not have the .probe/..driver_data
fields, which means that priv is not allocated.
This causes the NULL pointer dereference inside kszphy_config_reset().
Fix the problem by using the generic suspend/resume functions as before.
Another alternative would be to provide the .probe and .driver_data
information into the structure, but to be on the safe side, let's
just restore Ethernet functionality by using the generic suspend/resume.
Linus Torvalds [Thu, 5 May 2022 23:52:15 +0000 (16:52 -0700)]
Merge tag 'folio-5.18f' of git://git.infradead.org/users/willy/pagecache
Pull folio fixes from Matthew Wilcox:
"Two folio fixes for 5.18.
Darrick and Brian have done amazing work debugging the race I created
in the folio BIO iterator. The readahead problem was deterministic, so
easy to fix.
- Fix a race when we were calling folio_next() in the BIO folio iter
without holding a reference, meaning the folio could be split or
freed, and we'd jump to the next page instead of the intended next
folio.
- Fix readahead creating single-page folios instead of the intended
large folios when doing reads that are not a power of two in size"
* tag 'folio-5.18f' of git://git.infradead.org/users/willy/pagecache:
mm/readahead: Fix readahead with large folios
block: Do not call folio_next() on an unreferenced folio
Tetsuo Handa [Thu, 5 May 2022 01:53:53 +0000 (10:53 +0900)]
net: rds: use maybe_get_net() when acquiring refcount on TCP sockets
Eric Dumazet is reporting addition on 0 problem at rds_tcp_tune(), for
delayed works queued in rds_wq might be invoked after a net namespace's
refcount already reached 0.
Since rds_tcp_exit_net() from cleanup_net() calls flush_workqueue(rds_wq),
it is guaranteed that we can instead use maybe_get_net() from delayed work
functions until rds_tcp_exit_net() returns.
Note that I'm not convinced that all works which might access a net
namespace are already queued in rds_wq by the moment rds_tcp_exit_net()
calls flush_workqueue(rds_wq). If some race is there, rds_tcp_exit_net()
will fail to wait for work functions, and kmem_cache_free() could be
called from net_free() before maybe_get_net() is called from
rds_tcp_tune().
Linus Torvalds [Thu, 5 May 2022 22:50:27 +0000 (15:50 -0700)]
Merge tag 'devicetree-fixes-for-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Drop unused 'max-link-speed' in Apple PCIe
- More redundant 'maxItems/minItems' schema fixes
- Support values for pinctrl 'drive-push-pull' and 'drive-open-drain'
- Fix redundant 'unevaluatedProperties' in MT6360 LEDs binding
- Add missing 'power-domains' property to Cadence UFSHC
* tag 'devicetree-fixes-for-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pci: apple,pcie: Drop max-link-speed from example
dt-bindings: Drop redundant 'maxItems/minItems' in if/then schemas
dt-bindings: pinctrl: Allow values for drive-push-pull and drive-open-drain
dt-bindings: leds-mt6360: Drop redundant 'unevaluatedProperties'
dt-bindings: ufs: cdns,ufshc: Add power-domains
Daniel Starke [Wed, 4 May 2022 08:17:33 +0000 (10:17 +0200)]
tty: n_gsm: fix invalid gsmtty_write_room() result
gsmtty_write() does not prevent the user to use the full fifo size of 4096
bytes as allocated in gsm_dlci_alloc(). However, gsmtty_write_room() tries
to limit the return value by 'TX_SIZE' and returns a negative value if the
fifo has more than 'TX_SIZE' bytes stored. This is obviously wrong as
'TX_SIZE' is defined as 512.
Define 'TX_SIZE' to the fifo size and use it accordingly for allocation to
keep the current behavior. Return the correct remaining size of the fifo in
gsmtty_write_room() via kfifo_avail().
Daniel Starke [Wed, 4 May 2022 08:17:32 +0000 (10:17 +0200)]
tty: n_gsm: fix mux activation issues in gsm_config()
The current implementation activates the mux if it was restarted and opens
the control channel if the mux was previously closed and we are now acting
as initiator instead of responder, which is the default setting.
This has two issues.
1) No mux is activated if we keep all default values and only switch to
initiator. The control channel is not allocated but will be opened next
which results in a NULL pointer dereference.
2) Switching the configuration after it was once configured while keeping
the initiator value the same will not reopen the control channel if it was
closed due to parameter incompatibilities. The mux remains dead.
Fix 1) by always activating the mux if it is dead after configuration.
Fix 2) by always opening the control channel after mux activation.
Daniel Starke [Wed, 4 May 2022 08:17:31 +0000 (10:17 +0200)]
tty: n_gsm: fix buffer over-read in gsm_dlci_data()
'len' is decreased after each octet that has its EA bit set to 0, which
means that the value is encoded with additional octets. However, the final
octet does not decreases 'len' which results in 'len' being one byte too
long. A buffer over-read may occur in tty_insert_flip_string() as it tries
to read one byte more than the passed content size of 'data'.
Decrease 'len' also for the final octet which has the EA bit set to 1 to
write the correct number of bytes from the internal receive buffer to the
virtual tty.
serial: 8250_mtk: Make sure to select the right FEATURE_SEL
Set the FEATURE_SEL at probe time to make sure that BIT(0) is enabled:
this guarantees that when the port is configured as AP UART, the
right register layout is interpreted by the UART IP.
On MediaTek SoCs, the UART IP is 16550A compatible, but there are some
specific quirks: we are declaring a register shift of 2, but this is
only valid for the majority of the registers, as there are some that
are out of the standard layout.
Specifically, this driver is using definitions from serial_reg.h, where
we have a UART_EFR register defined as 2: this results in a 0x8 offset,
but there we have the FCR register instead.
The right offset for the EFR register on MediaTek UART is at 0x98,
so, following the decimal definition convention in serial_reg.h and
accounting for the register left shift of two, add and use the correct
register address for this IP, defined as decimal 38, so that the final
calculation results in (0x26 << 2) = 0x98.
Yang Yingliang [Thu, 5 May 2022 12:46:21 +0000 (20:46 +0800)]
tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Dan Vacura [Tue, 3 May 2022 20:10:38 +0000 (15:10 -0500)]
usb: gadget: uvc: allow for application to cleanly shutdown
Several types of kernel panics can occur due to timing during the uvc
gadget removal. This appears to be a problem with gadget resources being
managed by both the client application's v4l2 open/close and the UDC
gadget bind/unbind. Since the concept of USB_GADGET_DELAYED_STATUS
doesn't exist for unbind, add a wait to allow for the application to
close out.
projects / linux.git / log