Dan Carpenter [Thu, 13 Jul 2017 07:47:22 +0000 (10:47 +0300)]
IB/i40iw: Fix error code in i40iw_create_cq()
We accidentally forgot to set the error code if ib_copy_from_udata()
fails. It means we return ERR_PTR(0) which is NULL and results in a
NULL dereference in the callers.
Dan Carpenter [Thu, 13 Jul 2017 07:45:48 +0000 (10:45 +0300)]
IB/IPoIB: Fix error code in ipoib_add_port()
We accidentally don't see the error code on some of these error paths.
It means we return ERR_PTR(0) which is NULL and it results in a NULL
dereference in the caller.
If the physical buffer list entries (PBLEs) of a QP are freed
up at i40iw_dereg_mr, they can be assigned to a newly
created QP before the previous QP is destroyed. Fix this
by freeing PBLEs only when the QP is destroyed.
Shiraz Saleem [Fri, 23 Jun 2017 21:03:59 +0000 (16:03 -0500)]
i40iw: Free QP resources on CQP destroy QP failure
Current flow leaves software QP structures in memory if
Control Queue Pair (CQP) destroy QP OP fails. To fix this,
free QP resources on fail of CQP destroy QP OP.
Mustafa Ismail [Fri, 23 Jun 2017 21:03:56 +0000 (16:03 -0500)]
i40iw: Do not poll CCQ after it is destroyed
Control Queue Pair (CQP) OPs, in this case - Update SDs,
cannot poll the Control Completion Queue (CCQ) after CCQ is
destroyed. Instead, poll via registers.
Roman Kagan [Thu, 20 Jul 2017 14:26:40 +0000 (17:26 +0300)]
kvm: x86: hyperv: avoid livelock in oneshot SynIC timers
If the SynIC timer message delivery fails due to SINT message slot being
busy, there's no point to attempt starting the timer again until we're
notified of the slot being released by the guest (via EOM or EOI).
Even worse, when a oneshot timer fails to deliver its message, its
re-arming with an expiration time in the past leads to immediate retry
of the delivery, and so on, without ever letting the guest vcpu to run
and release the slot, which results in a livelock.
To avoid that, only start the timer when there's no timer message
pending delivery. When there is, meaning the slot is busy, the
processing will be restarted upon notification from the guest that the
slot is released.
Wanpeng Li [Thu, 20 Jul 2017 08:11:54 +0000 (01:11 -0700)]
KVM: VMX: Fix invalid guest state detection after task-switch emulation
This can be reproduced by EPT=1, unrestricted_guest=N, emulate_invalid_state=Y
or EPT=0, the trace of kvm-unit-tests/taskswitch2.flat is like below, it tries
to emulate invalid guest state task-switch:
It appears that the task-switch emulation updates rflags (and vm86
flag) only after the segments are loaded, causing vmx->emulation_required
to be set, when in fact invalid guest state emulation is not needed.
This patch fixes it by updating vmx->emulation_required after the
rflags (and vm86 flag) is updated in task-switch emulation.
Thanks Radim for moving the update to vmx__set_flags and adding Paolo's
suggestion for the check.
Martin Wilck [Thu, 13 Jul 2017 22:25:31 +0000 (00:25 +0200)]
nvmet: don't report 0-bytes in serial number
The NVME standard mandates that the SN, MN, and FR fields of the Identify
Controller Data Structure be "ASCII strings". That means that they may
not contain 0-bytes, not even string terminators.
nvmet: preserve controller serial number between reboots
The NVMe target has no way to preserve controller serial
IDs across reboots which breaks udev scripts doing
SYMLINK+="dev/disk/by-id/nvme-$env{ID_SERIAL}-part%n.
Export the randomly generated serial number via configfs and allow
setting of a serial via configfs to mitigate this breakage.
nvmet: Move serial number from controller to subsystem
The NVMe specification defines the serial number as:
"Serial Number (SN): Contains the serial number for the NVM subsystem
that is assigned by the vendor as an ASCII string. Refer to section
7.10 for unique identifier requirements. Refer to section 1.5 for ASCII
string requirements"
So move it from the controller to the subsystem, where it belongs.
Keith Busch [Wed, 12 Jul 2017 19:59:07 +0000 (15:59 -0400)]
nvme-pci: Remove nvme_setup_prps BUG_ON
This patch replaces the invalid nvme SGL kernel panic with a warning,
and returns an appropriate error. The warning will occur only on the
first occurance, and sgl details will be printed to help debug how the
request was allowed to form.
Peter Chen [Thu, 20 Jul 2017 11:48:30 +0000 (14:48 +0300)]
usb: xhci: fix spinlock recursion for USB2 test mode
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Shyam Sundar S K [Thu, 20 Jul 2017 11:48:28 +0000 (14:48 +0300)]
usb: xhci: Issue stop EP command only when the EP state is running
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
xhci: Bad Ethernet performance plugged in ASM1042A host
When USB Ethernet is plugged in ASMEDIA ASM1042A xHCI host, bad
performance was manifesting in Web browser use (like download
large file such as ISO image). It is known limitation of
ASM1042A that is not compatible with driver scheduling,
As a workaround we can modify flow control handling of ASM1042A.
The register we modify is changes the behavior
xhci: Fix NULL pointer dereference when cleaning up streams for removed host
This off by one in stream_id indexing caused NULL pointer dereference and
soft lockup on machines with USB attached SCSI devices connected to a
hotpluggable xhci controller.
The code that cleans up pending URBs for dead hosts tried to dereference
a stream ring at the invalid stream_id 0.
ep->stream_info->stream_rings[0] doesn't point to a ring.
Start looping stream_id from 1 like in all the other places in the driver,
and check that the ring exists before trying to kill URBs on it.
Mike Galbraith reported a situation where a WARN_ON_ONCE() call in DRM
code turned into an oops. As it turns out, WARN_ON_ONCE() seems to be
completely broken when called from a module.
The bug was introduced with the following commit:
19d436268dde ("debug: Add _ONCE() logic to report_bug()")
That commit changed WARN_ON_ONCE() to move its 'once' logic into the bug
trap handler. It requires a writable bug table so that the BUGFLAG_DONE
bit can be written to the flags to indicate the first warning has
occurred.
The bug table was made writable for vmlinux, which relies on
vmlinux.lds.S and vmlinux.lds.h for laying out the sections. However,
it wasn't made writable for modules, which rely on the ELF section
header flags.
Amir Goldstein [Tue, 18 Jul 2017 18:07:43 +0000 (21:07 +0300)]
ovl: check for bad and whiteout index on lookup
Index should always be of the same file type as origin, except for
the case of a whiteout index. A whiteout index should only exist
if all lower aliases have been unlinked, which means that finding
a lower origin on lookup whose index is a whiteout should be treated
as a lookup error.
Amir Goldstein [Tue, 18 Jul 2017 18:07:42 +0000 (21:07 +0300)]
ovl: do not cleanup directory and whiteout index entries
Directory index entries are going to be used for looking up
redirected upper dirs by lower dir fh when decoding an overlay
file handle of a merge dir.
Whiteout index entries are going to be used as an indication that
an exported overlay file handle should be treated as stale (i.e.
after unlink of the overlay inode).
We don't know the verification rules for directory and whiteout
index entries, because they have not been implemented yet, so fail
to mount overlay rw if those entries are found to avoid corrupting
an index that was created by a newer kernel.
inode_doinit_with_dentry() in SELinux wants to read the upper inode's xattr
to get security label, and ovl_xattr_get() calls ovl_dentry_real(), which
depends on dentry->d_inode, but d_inode is null and not initialized yet at
this point resulting in an Oops.
Fix by getting the upperdentry info from the inode directly in this case.
x86/platform/intel-mid: Fix a format string overflow warning
We have space for exactly three characters for the index in "max7315_%d_base",
but as GCC points out having more would cause an string overflow:
arch/x86/platform/intel-mid/device_libs/platform_max7315.c: In function 'max7315_platform_data':
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:26: error: '%d' directive writing between 1 and 11 bytes into a region of size 9 [-Werror=format-overflow=]
sprintf(base_pin_name, "max7315_%d_base", nr);
^~~~~~~~~~~~~~~~~
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:26: note: directive argument in the range [-2147483647, 2147483647]
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:3: note: 'sprintf' output between 15 and 25 bytes into a destination of size 17
sprintf(base_pin_name, "max7315_%d_base", nr);
This makes it use an snprintf() to truncate the string if that happened
rather than overflowing the stack. In practice, this is safe, because
there won't be a large number of max7315 devices in the systems, and
both the format and the length are defined by the firmware interface.
x86/io: Add "memory" clobber to insb/insw/insl/outsb/outsw/outsl
The x86 version of insb/insw/insl uses an inline assembly that does
not have the target buffer listed as an output. This can confuse
the compiler, leading it to think that a subsequent access of the
buffer is uninitialized:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_mgmt_scan_confirm’:
drivers/net/wireless/wl3501_cs.c:665:9: error: ‘sig.status’ is used uninitialized in this function [-Werror=uninitialized]
drivers/net/wireless/wl3501_cs.c:668:12: error: ‘sig.cap_info’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c: In function 'sb1000_rx':
drivers/net/sb1000.c:775:9: error: 'st[0]' is used uninitialized in this function [-Werror=uninitialized]
drivers/net/sb1000.c:776:10: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c:784:11: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I tried to mark the exact input buffer as an output here, but couldn't
figure it out. As suggested by Linus, marking all memory as clobbered
however is good enough too. For the outs operations, I also add the
memory clobber, to force the input to be written to local variables.
This is probably already guaranteed by the "asm volatile", but it can't
hurt to do this for symmetry.
arch/x86/math-emu/reg_add_sub.c: In function 'FPU_add':
arch/x86/math-emu/reg_add_sub.c:80:48: error: ?: using integer constants in boolean context [-Werror=int-in-bool-context]
This appears to be a bug in gcc-7.1.1, and I have reported it as
PR81484. The compiler suggests that code written as
if (a & b ? c : d)
is usually incorrect and should have been
if (a & (b ? c : d))
However, in this case, we correctly write
if ((a & b) ? c : d)
and should not get a warning for it.
This adds a dirty workaround for the problem, adding a comparison with
zero inside of the macro. The warning is currently disabled in the kernel,
so we may decide not to apply the patch, and instead wait for future gcc
releases to fix the problem. On the other hand, it seems to be the
only instance of this particular problem.
x86/fpu/math-emu: Fix possible uninitialized variable use
When building the kernel with "make EXTRA_CFLAGS=...", this overrides
the "PARANOID" preprocessor macro defined in arch/x86/math-emu/Makefile,
and we run into a build warning:
arch/x86/math-emu/reg_compare.c: In function ‘compare_i_st_st’:
arch/x86/math-emu/reg_compare.c:254:6: error: ‘f’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This fixes the implementation to work correctly even without the PARANOID
flag, and also fixes the Makefile to not use the EXTRA_CFLAGS variable
but instead use the ccflags-y variable in the Makefile that is meant
for this purpose.
perf/x86: Shut up false-positive -Wmaybe-uninitialized warning
The intialization function checks for various failure scenarios, but
unfortunately the compiler gets a little confused about the possible
combinations, leading to a false-positive build warning when
-Wmaybe-uninitialized is set:
arch/x86/events/core.c: In function ‘init_hw_perf_events’:
arch/x86/events/core.c:264:3: warning: ‘reg_fail’ may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/x86/events/core.c:264:3: warning: ‘val_fail’ may be used uninitialized in this function [-Wmaybe-uninitialized]
pr_err(FW_BUG "the BIOS has corrupted hw-PMU resources (MSR %x is %Lx)\n",
We can't actually run into this case, so this shuts up the warning
by initializing the variables to a known-invalid state.
Seunghun Han [Tue, 18 Jul 2017 09:20:44 +0000 (18:20 +0900)]
x86/ioapic: Pass the correct data to unmask_ioapic_irq()
One of the rarely executed code pathes in check_timer() calls
unmask_ioapic_irq() passing irq_get_chip_data(0) as argument.
That's wrong as unmask_ioapic_irq() expects a pointer to the irq data of
interrupt 0. irq_get_chip_data(0) returns NULL, so the following
dereference in unmask_ioapic_irq() causes a kernel panic.
The issue went unnoticed in the first place because irq_get_chip_data()
returns a void pointer so the compiler cannot do a type check on the
argument. The code path was added for machines with broken configuration,
but it seems that those machines are either not running current kernels or
simply do not longer exist.
Hand in irq_get_irq_data(0) as argument which provides the correct data.
Seunghun Han [Tue, 18 Jul 2017 11:03:51 +0000 (20:03 +0900)]
x86/acpi: Prevent out of bound access caused by broken ACPI tables
The bus_irq argument of mp_override_legacy_irq() is used as the index into
the isa_irq_to_gsi[] array. The bus_irq argument originates from
ACPI_MADT_TYPE_IO_APIC and ACPI_MADT_TYPE_INTERRUPT items in the ACPI
tables, but is nowhere sanity checked.
That allows broken or malicious ACPI tables to overwrite memory, which
might cause malfunction, panic or arbitrary code execution.
Add a sanity check and emit a warning when that triggers.
Imre Deak [Wed, 19 Jul 2017 13:46:32 +0000 (16:46 +0300)]
drm/mst: Avoid processing partially received up/down message transactions
Currently we may process up/down message transactions containing
uninitialized data. This can happen if there was an error during the
reception of any message in the transaction, but we happened to receive
the last message correctly with the end-of-message flag set.
To avoid this abort the reception of the transaction when the first
error is detected, rejecting any messages until a message with the
start-of-message flag is received (which will start a new transaction).
This is also what the DP 1.4 spec 2.11.8.2 calls for in this case.
In addtion this also prevents receiving bogus transactions without the
first message with the the start-of-message flag set.
v2:
- unchanged
v3:
- git add the part that actually skips messages after an error in
drm_dp_sideband_msg_build()
perf/core: Fix scheduling regression of pinned groups
Vince Weaver reported:
> I was tracking down some regressions in my perf_event_test testsuite.
> Some of the tests broke in the 4.11-rc1 timeframe.
>
> I've bisected one of them, this report is about
> tests/overflow/simul_oneshot_group_overflow
> This test creates an event group containing two sampling events, set
> to overflow to a signal handler (which disables and then refreshes the
> event).
>
> On a good kernel you get the following:
> Event perf::instructions with period 1000000
> Event perf::instructions with period 2000000
> fd 3 overflows: 946 (perf::instructions/1000000)
> fd 4 overflows: 473 (perf::instructions/2000000)
> Ending counts:
> Count 0: 946379875
> Count 1: 946365218
>
> With the broken kernels you get:
> Event perf::instructions with period 1000000
> Event perf::instructions with period 2000000
> fd 3 overflows: 938 (perf::instructions/1000000)
> fd 4 overflows: 318 (perf::instructions/2000000)
> Ending counts:
> Count 0: 946373080
> Count 1: 653373058
The root cause of the bug is that the following commit:
487f05e18a ("perf/core: Optimize event rescheduling on active contexts")
erronously assumed that event's 'pinned' setting determines whether the
event belongs to a pinned group or not, but in fact, it's the group
leader's pinned state that matters.
This was discovered by Vince in the test case described above, where two instruction
counters are grouped, the group leader is pinned, but the other event is not;
in the regressed case the counters were off by 33% (the difference between events'
periods), but should be the same within the error margin.
Fix the problem by looking at the group leader's pinning.
ipv6: avoid overflow of offset in ip6_find_1stfragopt
In some cases, offset can overflow and can cause an infinite loop in
ip6_find_1stfragopt(). Make it unsigned int to prevent the overflow, and
cap it at IPV6_MAXPLEN, since packets larger than that should be invalid.
This problem has been here since before the beginning of git history.
Colin Ian King [Wed, 19 Jul 2017 17:46:59 +0000 (18:46 +0100)]
net: tehuti: don't process data if it has not been copied from userspace
The array data is only populated with valid information from userspace
if cmd != SIOCDEVPRIVATE, other cases the array contains garbage on
the stack. The subsequent switch statement acts on a subcommand in
data[0] which could be any garbage value if cmd is SIOCDEVPRIVATE which
seems incorrect to me. Instead, just return EOPNOTSUPP for the case
where cmd == SIOCDEVPRIVATE to avoid this issue.
As a side note, I suspect that the original intention of the code
was for this ioctl to work just for cmd == SIOCDEVPRIVATE (and the
current logic is reversed). However, I don't wont to change the current
semantics in case any userspace code relies on this existing behaviour.
Detected by CoverityScan, CID#139647 ("Uninitialized scalar variable")
The duplicate CHANGEADDR event message is sent regardless of link
status whereas the setlink changes only generate a notification when
the link is up. Not sending a notification when the link is down breaks
dhcpcd which only processes hwaddr changes when the link is down.
Martin Hundebøll [Wed, 19 Jul 2017 06:17:02 +0000 (08:17 +0200)]
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
Commit f39908d3b1c45 ('net: dsa: mv88e6xxx: Set the CMODE for mv88e6390
ports 9 & 10') added support for setting the CMODE for the 6390X family,
but only enabled it for 9290 and 6390 - and left out 6390X.
Fix support for setting the CMODE on 6390X also by assigning
mv88e6390x_port_set_cmode() to the .port_set_cmode function pointer in
mv88e6390x_ops too.
Fixes: f39908d3b1c4 ("net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10") Signed-off-by: Martin Hundebøll <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Reviewed-by: Vivien Didelot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
Add SoC specific compatibility strings to the Broadcom DTE
based PTP clock binding document.
Fixed the document heading and node name.
Fixes: 80d6076140b2 ("dt-binding: ptp: add bindings document for dte based ptp clock") Signed-off-by: Arun Parameswaran <[email protected]> Acked-by: Rob Herring <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Currently llist_for_each_entry() and llist_for_each_entry_safe() iterate
until &pos->member != NULL. But when building the kernel with Clang,
the compiler assumes &pos->member cannot be NULL if the member's offset
is greater than 0 (which would be equivalent to the object being
non-contiguous in memory). Therefore the loop condition is always true,
and the loops become infinite.
To work around this, introduce the member_address_is_nonnull() macro,
which casts object pointer to uintptr_t, thus letting the member pointer
to be NULL.
Merge tag 'gcc-plugins-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull structure randomization updates from Kees Cook:
"Now that IPC and other changes have landed, enable manual markings for
randstruct plugin, including the task_struct.
This is the rest of what was staged in -next for the gcc-plugins, and
comes in three patches, largest first:
- mark "easy" structs with __randomize_layout
- mark task_struct with an optional anonymous struct to isolate the
__randomize_layout section
- mark structs to opt _out_ of automated marking (which will come
later)
And, FWIW, this continues to pass allmodconfig (normal and patched to
enable gcc-plugins) builds of x86_64, i386, arm64, arm, powerpc, and
s390 for me"
* tag 'gcc-plugins-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
randstruct: opt-out externally exposed function pointer structs
task_struct: Allow randomized layout
randstruct: Mark various structs for randomization
Merge tag 'ceph-for-4.13-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A number of small fixes for -rc1 Luminous changes plus a readdir race
fix, marked for stable"
* tag 'ceph-for-4.13-rc2' of git://github.com/ceph/ceph-client:
libceph: potential NULL dereference in ceph_msg_data_create()
ceph: fix race in concurrent readdir
libceph: don't call encode_request_finish() on MOSDBackoff messages
libceph: use alloc_pg_mapping() in __decode_pg_upmap_items()
libceph: set -EINVAL in one place in crush_decode()
libceph: NULL deref on osdmap_apply_incremental() error path
libceph: fix old style declaration warnings
Jim Mattson [Mon, 17 Jul 2017 19:00:34 +0000 (12:00 -0700)]
KVM: nVMX: Disallow VM-entry in MOV-SS shadow
Immediately following MOV-to-SS/POP-to-SS, VM-entry is
disallowed. This check comes after the check for a valid VMCS. When
this check fails, the instruction pointer should fall through to the
next instruction, the ALU flags should be set to indicate VMfailValid,
and the VM-instruction error should be set to 26 ("VM entry with
events blocked by MOV SS").
Paolo Bonzini [Fri, 14 Jul 2017 11:36:11 +0000 (13:36 +0200)]
KVM: nVMX: track NMI blocking state separately for each VMCS
vmx_recover_nmi_blocking is using a cached value of the guest
interruptibility info, which is stored in vmx->nmi_known_unmasked.
vmx_recover_nmi_blocking is run for both normal and nested guests,
so the cached value must be per-VMCS.
This fixes eventinj.flat in a nested non-EPT environment. With EPT it
works, because the EPT violation handler doesn't have the
vmx->nmi_known_unmasked optimization (it is unnecessary because, unlike
vmx_recover_nmi_blocking, it can just look at the exit qualification).
Thanks to Wanpeng Li for debugging the testcase and providing an initial
patch.
PM / Domains: defer dev_pm_domain_set() until genpd->attach_dev succeeds if present
If the genpd->attach_dev or genpd->power_on fails, genpd_dev_pm_attach
may return -EPROBE_DEFER initially. However genpd_alloc_dev_data sets
the PM domain for the device unconditionally.
When subsequent attempts are made to call genpd_dev_pm_attach, it may
return -EEXISTS checking dev->pm_domain without re-attempting to call
attach_dev or power_on.
platform_drv_probe then attempts to call drv->probe as the return value
-EEXIST != -EPROBE_DEFER, which may end up in a situation where the
device is accessed without it's power domain switched on.
Joel Fernandes [Thu, 13 Jul 2017 02:14:16 +0000 (19:14 -0700)]
tracing/ring_buffer: Try harder to allocate
ftrace can fail to allocate per-CPU ring buffer on systems with a large
number of CPUs coupled while large amounts of cache happening in the
page cache. Currently the ring buffer allocation doesn't retry in the VM
implementation even if direct-reclaim made some progress but still
wasn't able to find a free page. On retrying I see that the allocations
almost always succeed. The retry doesn't happen because __GFP_NORETRY is
used in the tracer to prevent the case where we might OOM, however if we
drop __GFP_NORETRY, we risk destabilizing the system if OOM killer is
triggered. To prevent this situation, use the __GFP_RETRY_MAYFAIL flag
introduced recently [1].
Tested the following still succeeds without destabilizing a system with
1GB memory.
echo 300000 > /sys/kernel/debug/tracing/buffer_size_kb
Dan Carpenter [Mon, 17 Jul 2017 08:14:26 +0000 (11:14 +0300)]
KVM: x86: masking out upper bits
kvm_read_cr3() returns an unsigned long and gfn is a u64. We intended
to mask out the bottom 5 bits but because of the type issue we mask the
top 32 bits as well. I don't know if this is a real problem, but it
causes static checker warnings.
Merge tag 'fixes-for-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.13-rc2
First set of fixes for the current -rc cycle. Only three fixes on dwc3
this time around (proper order for getting a PHY reference, fix for
unmapping DMA and a fix for requesting IRQ on the OMAP glue layer).
Most fixes are on the renesas USB controller, fixing several old bugs
with most going to stable.
dwc2 also learned that it *must* reset USB Address to zero on Reset
interrupts.
Apart from these, some drivers needed HAS_DMA dependency and there's a
sparse warning fix for bdc udc.
usb: renesas_usbhs: gadget: disable all eps when the driver stops
A gadget driver will not disable eps immediately when ->disconnect()
is called. But, since this driver assumes all eps stop after
the ->disconnect(), unexpected behavior happens (especially in system
suspend).
So, this patch disables all eps in usbhsg_try_stop(). After disabling
eps by renesas_usbhs driver, since some functions will be called by
both a gadget and renesas_usbhs driver, renesas_usbhs driver should
protect uep->pipe. To protect uep->pipe easily, this patch adds a new
lock in struct usbhsg_uep.
usb: renesas_usbhs: fix usbhsc_resume() for !USBHSF_RUNTIME_PWCTRL
This patch fixes an issue that some registers may be not initialized
after resume if the USBHSF_RUNTIME_PWCTRL is not set. Otherwise,
if a cable is not connected, the driver will not enable INTENB0.VBSE
after resume. And then, the driver cannot detect the VBUS.
...by reusing the namespace id for the device-dax instance name.
Now that we have decided that there will never by more than one
device-dax instance per libnvdimm-namespace parent device [1], we can
directly reuse the namepace ids. There are some possible follow-on
cleanups, but those are saved for a later patch to simplify the -stable
backport.
Dan Carpenter [Tue, 18 Jul 2017 19:38:56 +0000 (22:38 +0300)]
netfilter: fix netfilter_net_init() return
We accidentally return an uninitialized variable.
Fixes: cf56c2f892a8 ("netfilter: remove old pre-netns era hook api") Signed-off-by: Dan Carpenter <[email protected]> Acked-by: Pablo Neira Ayuso <[email protected]> Signed-off-by: David S. Miller <[email protected]>
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Missing netlink message sanity check in nfnetlink, patch from
Mateusz Jurczyk.
2) We now have netfilter per-netns hooks, so let's kill global hook
infrastructure, this infrastructure is known to be racy with netns.
We don't care about out of tree modules. Patch from Florian Westphal.
3) find_appropriate_src() is buggy when colissions happens after the
conversion of the nat bysource to rhashtable. Also from Florian.
4) Remove forward chain in nf_tables arp family, it's useless and it is
causing quite a bit of confusion, from Florian Westphal.
5) nf_ct_remove_expect() is called with the wrong parameter, causing
kernel oops, patch from Florian Westphal.
====================
Paolo Abeni [Tue, 18 Jul 2017 09:57:55 +0000 (11:57 +0200)]
udp: preserve skb->dst if required for IP options processing
Eric noticed that in udp_recvmsg() we still need to access
skb->dst while processing the IP options.
Since commit 0a463c78d25b ("udp: avoid a cache miss on dequeue")
skb->dst is no more available at recvmsg() time and bad things
will happen if we enter the relevant code path.
This commit address the issue, avoid clearing skb->dst if
any IP options are present into the relevant skb.
Since the IP CB is contained in the first skb cacheline, we can
test it to decide to leverage the consume_stateless_skb()
optimization, without measurable additional cost in the faster
path.
Merge tag 'md/4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md
Pull MD fixes from Shaohua Li:
- raid5-ppl fix by Artur. This one is introduced in this release cycle.
- raid5 reshape fix by Xiao. This is an old bug and will be added to
stable.
- bitmap fix by Guoqing.
* tag 'md/4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid5-ppl: use BIOSET_NEED_BVECS when creating bioset
Raid5 should update rdev->sectors after reshape
md/bitmap: don't read page from device with Bitmap_sync
atm: zatm: Fix an error handling path in 'zatm_init_one()'
If 'dma_set_mask_and_coherent()' fails, we must undo the previous
'pci_request_regions()' call.
Adjust corresponding 'goto' to jump at the right place of the error
handling path.
Fixes: 58d607d3e52f ("tcp: provide skb->hash to synack packets") Signed-off-by: Alexander Potapenko <[email protected]> Acked-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
ppp: Fix false xmit recursion detect with two ppp devices
The global percpu variable ppp_xmit_recursion is used to detect the ppp
xmit recursion to avoid the deadlock, which is caused by one CPU tries to
lock the xmit lock twice. But it would report false recursion when one CPU
wants to send the skb from two different PPP devices, like one L2TP on the
PPPoE. It is a normal case actually.
Now use one percpu member of struct ppp instead of the gloable variable to
detect the xmit recursion of one ppp device.
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"First set of -rc fixes for 4.13 cycle:
- misc iSER fixes
- namespace fixups
- fix the fact that IPoIB didn't use the proper API for noio mem allocs
- rxe driver fixes
- hns_roce fixes
- misc core fixes
- misc IPoIB fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (27 commits)
IB/core: Allow QP state transition from reset to error
IB/hns: Fix for checkpatch.pl comment style warnings
IB/hns: Fix the bug with modifying the MAC address without removing the driver
IB/hns: Fix the bug with rdma operation
IB/hns: Fix the bug with wild pointer when destroy rc qp
IB/hns: Fix the bug of polling cq failed for loopback Qps
IB/rxe: Set dma_mask and coherent_dma_mask
IB/rxe: Fix kernel panic from skb destructor
IB/ipoib: Let lower driver handle get_stats64 call
IB/core: Add ordered workqueue for RoCE GID management
IB/mlx5: Clean mr_cache debugfs in case of failure
IB/core: Remove NOIO QP create flag
{net, IB}/mlx4: Remove gfp flags argument
IB/{rdmavt, qib, hfi1}: Remove gfp flags argument
IB/IPoIB: Convert IPoIB to memalloc_noio_* calls
IB/IPoIB: Forward MTU change to driver below
IB: Convert msleep below 20ms to usleep_range
IB/uverbs: Make use of ib_modify_qp variant to avoid resolving DMAC
IB/core: Introduce modify QP operation with udata
IB/core: Don't resolve IP address to the loopback device
...
Jan Kara [Wed, 21 Jun 2017 13:02:47 +0000 (15:02 +0200)]
hfsplus: Don't clear SGID when inheriting ACLs
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by creating __hfsplus_set_posix_acl() function that does
not call posix_acl_update_mode() and use it when inheriting ACLs. That
prevents SGID bit clearing and the mode has been properly set by
posix_acl_create() anyway.
usb: gadget: udc: renesas_usb3: protect usb3_ep->started in usb3_start_pipen()
This patch fixes an issue that unexpected behavior happens when
both the interrupt handler and renesas_usb3_ep_enable() are called.
In this case, since usb3_start_pipen() checked the usb3_ep->started,
but the flags was not protected. So, this patch protects the flag
by usb3->lock. Since renesas_usb3_ep_enable() for EP0 will be not called,
this patch doesn't take care of usb3_start_pipe0().
usb: gadget: udc: renesas_usb3: fix zlp transfer by the dmac
The dedicated dmac can transfer a zero-length-packet (zlp) if some bits
of the USB_COM_CON register. However, the commit 2d4aa21a73ba ("usb:
gadget: udc: renesas_usb3: add support for dedicated DMAC") didn't set
the bits to 1. So, this patch fixes it.
Fixes: 2d4aa21a73b ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC) Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
usb: gadget: udc: renesas_usb3: fix free size in renesas_usb3_dma_free_prd()
The commit 2d4aa21a73ba ("usb: gadget: udc: renesas_usb3: add support
for dedicated DMAC") has a bug in the renesas_usb3_dma_free_prd().
The size of dma_free_coherent() should be the same with dma_alloc_coherent()
Otherwise, this code causes a WARNING by mm/page_alloc.c when
renesas_usb3_dma_free_prd() is called. So, this patch fixes it.
Fixes: 2d4aa21a73ba ("usb: gadget: udc: renesas_usb3: add support for dedicated DMAC") Reviewed-by: Geert Uytterhoeven <[email protected]> Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
Jiri Olsa [Fri, 14 Jul 2017 16:35:51 +0000 (18:35 +0200)]
perf/x86/intel: Fix debug_store reset field for freq events
There's a bug in PEBs event enabling code, that prevents PEBS
freq events to work properly after non freq PEBS event was run.
freq events - perf_event_attr::freq set
-F <freq> option of perf record
PEBS events - perf_event_attr::precise_ip > 0
default for perf record
Like in following example with CPU 0 busy, we expect ~10000 samples
for following perf tool run:
# perf record -F 10000 -C 0 sleep 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.640 MB perf.data (10031 samples) ]
Everything's fine, but once we run non freq PEBS event like:
# perf record -c 10000 -C 0 sleep 1
[ perf record: Woken up 4 times to write data ]
[ perf record: Captured and wrote 1.053 MB perf.data (20061 samples) ]
the freq events start to fail like this:
# perf record -F 10000 -C 0 sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.185 MB perf.data (40 samples) ]
The issue is in non freq PEBs event initialization of debug_store reset
field, which value is used to auto-reload the counter value after PEBS
event drain. This value is not being used for PEBS freq events, but once
we run non freq event it stays in debug_store data and screws the
sample_freq counting for PEBS freq events.
Kan Liang [Wed, 12 Jul 2017 13:44:23 +0000 (09:44 -0400)]
perf/x86/intel: Add Goldmont Plus CPU PMU support
Add perf core PMU support for Intel Goldmont Plus CPU cores:
- The init code is based on Goldmont.
- There is a new cache event list, based on the Goldmont cache event
list.
- All four general-purpose performance counters support PEBS.
- The first general-purpose performance counter is for reduced skid
PEBS mechanism. Using :ppp to indicate the event which want to do
reduced skid PEBS.
- Goldmont Plus has 4-wide pipeline for Topdown
Jan Kara [Tue, 18 Jul 2017 10:27:56 +0000 (12:27 +0200)]
isofs: Fix off-by-one in 'session' mount option parsing
According to ECMA-130 standard maximum valid track number is 99. Since
'session' mount option starts indexing at 0 (and we add 1 to the passed
number), we should refuse value 99. Also the condition in
isofs_get_last_session() unnecessarily repeats the check - remove it.
Michael Ellerman [Fri, 14 Jul 2017 06:51:23 +0000 (16:51 +1000)]
powerpc/mm: Mark __init memory no-execute when STRICT_KERNEL_RWX=y
Currently even with STRICT_KERNEL_RWX we leave the __init text marked
executable after init, which is bad.
Add a hook to mark it NX (no-execute) before we free it, and implement
it for radix and hash.
Note that we use __init_end as the end address, not _einittext,
because overlaps_kernel_text() uses __init_end, because there are
additional executable sections other than .init.text between
__init_begin and __init_end.
Tested on radix and hash with:
0:mon> p $__init_begin
*** 400 exception occurred
Fixes: 1e0fc9d1eb2b ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs") Signed-off-by: Michael Ellerman <[email protected]>
reiserfs: preserve i_mode if __reiserfs_set_acl() fails
When changing a file's acl mask, reiserfs_set_acl() will first set the
group bits of i_mode to the value of the mask, and only then set the
actual extended attribute representing the new acl.
If the second part fails (due to lack of space, for example) and the
file had no acl attribute to begin with, the system will from now on
assume that the mask permission bits are actual group permission bits,
potentially granting access to the wrong users.
Prevent this by only changing the inode mode after the acl has been set.
When changing a file's acl mask, ext2_set_acl() will first set the group
bits of i_mode to the value of the mask, and only then set the actual
extended attribute representing the new acl.
If the second part fails (due to lack of space, for example) and the file
had no acl attribute to begin with, the system will from now on assume
that the mask permission bits are actual group permission bits, potentially
granting access to the wrong users.
Prevent this by only changing the inode mode after the acl has been set.
[JK: Rebased on top of "ext2: Don't clear SGID when inheriting ACLs"] Signed-off-by: Ernesto A. Fernández <[email protected]> Signed-off-by: Jan Kara <[email protected]>
projects / linux.git / log