David S. Miller [Mon, 2 Jan 2017 20:23:34 +0000 (15:23 -0500)]
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
For core revision 3.x Address-Aligned Beats is available in two registers.
The DT property snps,aal was created for AAL in the DMA bus register,
which is a read/write bit.
The DT property snps,axi_all was created for AXI_AAL in the AXI bus mode
register, which is a read only bit that reflects the value of AAL in the
DMA bus register.
Since the value of snps,axi_all is never used in the driver,
and since the property was created for a bit that is read only,
it should be safe to remove the property.
David S. Miller [Mon, 2 Jan 2017 02:02:21 +0000 (21:02 -0500)]
Merge branch 'qed-driver-updates'
Yuval Mintz says:
====================
qed*: Driver updates
The more interesting changes in this series include:
- Restructuring of the qede files - qede_main.c has grown big and this
series splits it into 3 parts [patches #2 and #3].
- Some significant changes in the API through which RSS indirection
table gets configured [#8].
- Support for ndo_set_vf_trust() [#9] which would regulate which VFs
are allowed to use promisc/multi-promisc mode.
It also contains various minor changes to qed/qede, as well as
non-functional changes [#1, #12] to complement other changes.
====================
Mintz, Yuval [Sun, 1 Jan 2017 11:57:07 +0000 (13:57 +0200)]
qed*: RSS indirection based on queue-handles
A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Mintz, Yuval [Sun, 1 Jan 2017 11:57:04 +0000 (13:57 +0200)]
qede: Postpone reallocation until NAPI end
During Rx flow driver allocates a replacement buffer each time
it consumes an Rx buffer. Failing to do so, it would consume the
currently processed buffer and re-post it on the ring.
As a result, the Rx ring is always completely full [from driver POV].
We now allow the Rx ring to shorten by doing the re-allocations
at the end of the NAPI run. The only limitation is that we still want to
make sure each time we reallocate that we'd still have sufficient
elements in the Rx ring to guarantee that FW would be able to post
additional data and trigger an interrupt.
Mintz, Yuval [Sun, 1 Jan 2017 11:57:03 +0000 (13:57 +0200)]
qed*: Change maximal number of queues
Today qede requests contexts that would suffice for 64 'whole'
combined queues [192 meant for 64 rx, tx and xdp tx queues],
but registers netdev and limits the number of queues based on
information received by qed. In turn, qed doesn't take context
into account when informing qede how many queues it can support.
This would lead to a configuration problem in case user tries
configuring >64 combined queues to interface [or >96 in case
xdp isn't enabled]. Since we don't have a mangement firware
that actually provides so many interrupt lines to a single
device we're currently safe but that's about to change soon.
The new maximum is hence changed:
- For RoCE devices, the limit would remain 64.
- For non-RoCE devices, the limit might be higher [depending
on the actual configuration of the device].
qed would start enforcing that limit in both scenarios.
Mintz, Yuval [Sun, 1 Jan 2017 11:57:00 +0000 (13:57 +0200)]
qed*: Update to dual-license
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Thomas Preisner [Fri, 30 Dec 2016 02:37:54 +0000 (03:37 +0100)]
net: 3com: typhoon: typhoon_init_one: make return values more specific
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Relax the check in setsockopt to allow setting mc_index to an L3 slave if
sk_bound_dev_if points to an L3 master.
Make a similar change for IPv6. In this case change the device lookup to
take the rcu_read_lock avoiding a refcnt. The rcu lock is also needed for
the lookup of a potential L3 master device.
This really only silences a setsockopt failure since uses of mc_index are
secondary to sk_bound_dev_if if it is set. In both cases, if either index
is an L3 slave or master, lookups are directed to the same FIB table so
relaxing the check at setsockopt time causes no harm.
Patch is based on a suggested change by Darwin for a problem noted in
their code base.
Ping-Ke Shih [Wed, 28 Dec 2016 21:40:04 +0000 (15:40 -0600)]
rtlwifi: Fix alignment issues
The addresses of Wlan NIC registers are natural alignment, but some
drivers have bugs. These are evident on platforms that need natural
alignment to access registers. This change contains the following:
1. Function _rtl8821ae_dbi_read() is used to read one byte from DBI,
thus it should use rtl_read_byte().
2. Register 0x4C7 of 8192ee is single byte.
Bhumika Goyal [Sat, 17 Dec 2016 22:57:24 +0000 (04:27 +0530)]
libertas: constify cfg80211_ops structures
cfg80211_ops structures are only passed as an argument to the function
wiphy_new. This argument is of type const, so cfg80211_ops strutures
having this property can be declared as const.
Done using Coccinelle
Larry Finger [Thu, 15 Dec 2016 18:23:10 +0000 (12:23 -0600)]
rtlwifi: Remove some redundant code
The symbol DBG_EMERG is no longer used and is removed.
In a number of places, the code has redundant messages. For example, if
the failure for the firmware to run is logged, it is not necessary to
log that the firmware has been started. In addition, extraneous braces are
removed.
Larry Finger [Thu, 15 Dec 2016 18:23:09 +0000 (12:23 -0600)]
rtlwifi: rtl8188ee: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:08 +0000 (12:23 -0600)]
rtlwifi: rtl8192c-common: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:07 +0000 (12:23 -0600)]
rtlwifi: rtl8192ce: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:06 +0000 (12:23 -0600)]
rtlwifi: rtl8192cu: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:05 +0000 (12:23 -0600)]
rtlwifi: rtl8192de: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:04 +0000 (12:23 -0600)]
rtlwifi: rtl8192se: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:03 +0000 (12:23 -0600)]
rtlwifi: rtl8723-common: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:02 +0000 (12:23 -0600)]
rtlwifi: rtl8192ee: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:01 +0000 (12:23 -0600)]
rtlwifi: rtl8723ae: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:23:00 +0000 (12:23 -0600)]
rtlwifi: rtl8723be: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
Larry Finger [Thu, 15 Dec 2016 18:22:59 +0000 (12:22 -0600)]
rtlwifi: rtl8821ae: Remove all instances of DBG_EMERG
This is a step toward eliminating the RT_TRACE macros. Those calls that
have DBG_EMERG as the level are always logged, and they represent error
conditions, thus they are replaced with pr_err().
rt2800: replace msleep() with usleep_range() on channel switch
msleep(1) can sleep much more time then requested 1ms, this is not good
on channel switch, which we want to be performed fast (i.e. to make scan
faster). Replace msleep() with usleep_range(), which has much smaller
maximum sleeping time boundary.
We need to perform different actions (AGC and VCO calibrations and VGC
tuning) periodically at different intervals. We don't need separate
works for those, we can use link tuner work and just check for proper
interval on it.
This fixes performing AGC and VCO calibration when scanning on STA
mode. We need to be on-channel to perform those calibrations.
rt2800: set MAX_PSDU len according to remote STAs capabilities
MAX_LEN_CFG_MAX_PSDU specify maximum transmitted by HW AMPDU length
(0 - 8kB, 1 - 16kB, 2 - 32kB, 3 - 64kB). Set this option according to
remote stations capabilities (based on HT ampdu_factor). However limit
the value based our hardware TX capabilities as some chips can not send
more than 16kB (factor 1). Limit for all chips is currently 32kB
(factor 2), but perhaps for some chips this could be increased
to 64kB by setting drv_data->max_psdu to 3.
Since MAX_LEN_CFG_MAX_PSDU is global setting, on multi stations modes
(AP, IBSS, mesh) we limit according to less capable remote STA. We can
not set bigger value to speed up communication with some stations and
do not break communication with slow stations.
Johannes Berg [Wed, 7 Dec 2016 06:36:46 +0000 (07:36 +0100)]
iwlegacy: make il3945_mac_ops __ro_after_init
There's no need for this to be only __read_mostly, since
it's only written in a single way depending on the module
parameter, so that can be moved into the module's __init
function, and the ops can be __ro_after_init.
This is a little bit safer since it means the ops can't
be overwritten (accidentally or otherwise), which would
otherwise cause an arbitrary function or bad pointer to
be called.
mwifiex: sdio: fix use after free issue for save_adapter
If we have sdio work requests received when sdio card reset is
happening, we may end up accessing older save_adapter pointer
later which is already freed during card reset.
This patch solves the problem by cancelling those pending requests.
ath10k: enable advertising support for channel 169, 5Ghz
Enable advertising support for channel 169, 5Ghz so that
based on the regulatory domain(country code) this channel
shall be active for use. For example in countries like India
this channel shall be available for use with latest regulatory updates
Ryan Hsu [Thu, 22 Dec 2016 23:02:37 +0000 (15:02 -0800)]
ath10k: ignore configuring the incorrect board_id
With command to get board_id from otp, in the case of following
boot get otp board id result 0x00000000 board_id 0 chip_id 0
boot using board name 'bus=pci,bmi-chip-id=0,bmi-board-id=0"
...
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=0 from
ath10k/QCA6174/hw3.0/board-2.bin
The invalid board_id=0 will be used as index to search in the board-2.bin.
Ignore the case with board_id=0, as it means the otp is not carrying
the board id information.
Ryan Hsu [Thu, 22 Dec 2016 22:31:46 +0000 (14:31 -0800)]
ath10k: recal the txpower when removing interface
The txpower is being recalculated when adding interface to make sure
txpower won't overshoot the spec, and when removing the interface,
the txpower should again to be recalculated to restore the correct value
from the active interface list.
Following is one of the scenario
vdev0 is created as STA and connected: txpower:23
vdev1 is created as P2P_DEVICE for control interface: txpower:0
vdev2 is created as p2p go/gc interface: txpower is 21
So the vdev2@txpower:21 will be set to firmware when vdev2 is created.
When we tear down the vdev2, the txpower needs to be recalculated to
re-set it to vdev0@txpower:23 as vdev0/vdev1 are the active interface.
ath10k_pci mac vdev 0 peer create 8c:fd:f0:01:62:98
ath10k_pci mac vdev_id 0 txpower 23
... (adding interface)
ath10k_pci mac vdev create 2 (add interface) type 1 subtype 3
ath10k_pci mac vdev_id 2 txpower 21
ath10k_pci mac txpower 21
... (removing interface)
ath10k_pci mac vdev 2 delete (remove interface)
ath10k_pci vdev 1 txpower 0
ath10k_pci vdev 0 txpower 23
ath10k_pci mac txpower 23
Arun Khandavalli [Wed, 21 Dec 2016 12:19:21 +0000 (14:19 +0200)]
ath10k: support dev_coredump for crash dump
Whenever firmware crashes, and both CONFIG_ATH10K_DEBUGFS and
CONFIG_ALLOW_DEV_COREDUMP are enabled, dump information about the crash via a
devcoredump device. Dump can be read from userspace for further analysis from:
/sys/class/devcoredump/devcd*/data
As until now we have provided the firmware crash dump file via fw_crash_dump
debugfs keep it still available but deprecate and a warning print that the user
should switch to using dev_coredump.
Future improvement would be not to depend on CONFIG_ATH10K_DEBUGFS, as there
might be systems which want to get the firmware crash dump but not enable
debugfs. How to handle memory consumption is also something which needs to be
taken into account.
Ryan Hsu [Tue, 13 Dec 2016 22:55:19 +0000 (14:55 -0800)]
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Ath10k reports the phy capability that supports P2P_DEVICE interface.
When we use the P2P supported wpa_supplicant to start connection, it'll
create two interfaces, one is wlan0 (vdev_id=0) and one is P2P_DEVICE
p2p-dev-wlan0 which is for p2p control channel (vdev_id=1).
ath10k_pci mac vdev create 0 (add interface) type 2 subtype 0
ath10k_add_interface: vdev_id: 0, txpower: 0, bss_power: 0
...
ath10k_pci mac vdev create 1 (add interface) type 2 subtype 1
ath10k_add_interface: vdev_id: 1, txpower: 0, bss_power: 0
And the txpower in per vif bss_conf will only be set to valid tx power when
the interface is assigned with channel_ctx.
But this P2P_DEVICE interface will never be used for any connection, so
that the uninitialized bss_conf.txpower=0 is assinged to the
arvif->txpower when interface created.
Since the txpower configuration is firmware per physical interface.
So the smallest txpower of all vifs will be the one limit the tx power
of the physical device, that causing the low txpower issue on other
active interfaces.
wlan0: Limiting TX power to 21 (24 - 3) dBm
ath10k_pci mac vdev_id 0 txpower 21
ath10k_mac_txpower_recalc: vdev_id: 1, txpower: 0
ath10k_mac_txpower_recalc: vdev_id: 0, txpower: 21
ath10k_pci mac txpower 0
This issue only happens when we use the wpa_supplicant that supports
P2P or if we use the iw tool to create the control P2P_DEVICE interface.
ath10k: fix potential memory leak in ath10k_wmi_tlv_op_pull_fw_stats()
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...)
function, which allocates memory. If any of the three error-paths are
taken, this tb needs to be freed.
Felix Manlunas [Fri, 30 Dec 2016 01:04:47 +0000 (17:04 -0800)]
liquidio: optimize reads from Octeon PCI console
Reads from Octeon PCI console are inefficient because before each read
operation, a dynamic mapping to Octeon DRAM is set up. This patch replaces
the repeated setup of a dynamic mapping with a one-time setup of a static
mapping.
Oftenly, introducing side effects on packet processing on the other half
of the stack by adjusting one of TX/RX via sysctl is not desirable.
There are cases of demand for asymmetric, orthogonal configurability.
This holds true especially for nodes where RPS for RFS usage on top is
configured and therefore use the 'old dev_weight'. This is quite a
common base configuration setup nowadays, even with NICs of superior processing
support (e.g. aRFS).
A good example use case are nodes acting as noSQL data bases with a
large number of tiny requests and rather fewer but large packets as responses.
It's affordable to have large budget and rx dev_weights for the
requests. But as a side effect having this large a number on TX
processed in one run can overwhelm drivers.
This patch therefore introduces an independent configurability via sysctl to
userland.
David S. Miller [Thu, 29 Dec 2016 19:37:25 +0000 (14:37 -0500)]
Merge branch 'bnxt_en-updates'
Michael Chan says:
====================
bnxt_en: updates for net-next.
This patch series for net-next contains cleanups, new features and minor
fixes. The driver specific busy polling code is removed to use busy
polling support in core networking. Hardware RFS support is enhanced with
added ipv6 flows support and VF support. A new scheme to allocate TX
rings from the firmware is implemented for newer chips and firmware. Plus
some misc. cleanups, minor fixes, and to add the maintainer entry. Please
review.
====================
Michael Chan [Thu, 29 Dec 2016 17:13:43 +0000 (12:13 -0500)]
bnxt_en: Handle no aggregation ring gracefully.
The current code assumes that we will always have at least 2 rx rings, 1
will be used as an aggregation ring for TPA and jumbo page placements.
However, it is possible, especially on a VF, that there is only 1 rx
ring available. In this scenario, the current code will fail to initialize.
To handle it, we need to properly set up only 1 ring without aggregation.
Set a new flag BNXT_FLAG_NO_AGG_RINGS for this condition and add logic to
set up the chip to place RX data linearly into a single buffer per packet.
Michael Chan [Thu, 29 Dec 2016 17:13:42 +0000 (12:13 -0500)]
bnxt_en: Set default completion ring for async events.
With the added support for the bnxt_re RDMA driver, both drivers can be
allocating completion rings in any order. The firmware does not know
which completion ring should be receiving async events. Add an
extra step to tell firmware the completion ring number for receiving
async events after bnxt_en allocates the completion rings.
Michael Chan [Thu, 29 Dec 2016 17:13:41 +0000 (12:13 -0500)]
bnxt_en: Implement new scheme to reserve tx rings.
In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Michael Chan [Thu, 29 Dec 2016 17:13:38 +0000 (12:13 -0500)]
bnxt_en: Add new hardware RFS mode.
The existing hardware RFS mode uses one hardware RSS context block
per ring just to calculate the RSS hash. This is very wasteful and
prevents VF functions from using it. The new hardware mode shares
the same hardware RSS context for RSS placement and RFS steering.
This allows VFs to enable RFS.
Michael Chan [Thu, 29 Dec 2016 17:13:37 +0000 (12:13 -0500)]
bnxt_en: Refactor code that determines RFS capability.
Add function bnxt_rfs_supported() that determines if the chip supports
RFS. Refactor the existing function bnxt_rfs_capable() that determines
if run-time conditions support RFS.
Michael Chan [Thu, 29 Dec 2016 17:13:34 +0000 (12:13 -0500)]
bnxt_en: Fix and clarify link_info->advertising.
The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16. We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.
Michael Chan [Thu, 29 Dec 2016 17:13:33 +0000 (12:13 -0500)]
bnxt_en: Improve the IRQ disable sequence during shutdown.
The IRQ is disabled by writing to the completion ring doorbell. This
should be done before the hardware completion ring is freed for correctness.
The current code disables IRQs after all the completion rings are freed.
Fix it by calling bnxt_disable_int_sync() before freeing the completion
rings. Rearrange the code to avoid forward declaration.
Dave Jones [Wed, 28 Dec 2016 16:53:18 +0000 (11:53 -0500)]
ipv6: remove unnecessary inet6_sk check
np is already assigned in the variable declaration of ping_v6_sendmsg.
At this point, we have already dereferenced np several times, so the
NULL check is also redundant.
jpinto [Wed, 28 Dec 2016 12:57:48 +0000 (12:57 +0000)]
stmmac: enable rx queues
When the hardware is synthesized with multiple queues, all queues are
disabled for default. This patch adds the rx queues configuration.
This patch was successfully tested in a Synopsys QoS Reference design.
Joe Perches [Thu, 22 Dec 2016 03:54:53 +0000 (19:54 -0800)]
fddi: skfp: Use more common logging styles
Several macros use non-standard styles where format and arguments
are not verified. Convert these to a more typical fmt, ##__VA_ARGS__
use so format and arguments match as appropriate.
Miscellanea:
o Fix format and argument mismatches
o Realign and reindent misindented block
o Strip newlines from formats and add to macro defines
o Coalesce a few consecutive logging uses to more simple single uses
ath10k: set CTS protection VDEV param only if VDEV is up
The cts protection vdev parameter, in new QCA9377 TF2.0 firmware,
requires bss peer to be created for the STATION vdev type.
bss peer is being allocated by the firmware after vdev_start/_up commands.
mac80211 may call the cts protection setup at any time, so the
we needs to track the situation and defer the cts configuration
to prevent firmware asserts, like below:
Similarly to QCA6174, QCA9377 requires the CE5 configuration to be
available for other feature. Use the ath10k_pci_override_ce_config()
for it as well.
This is required for TF2.0 firmware. Previous FW revisions were
working fine without this patch.
Fixes: a70587b3389a ("ath10k: configure copy engine 5 for HTT messages") Signed-off-by: Bartosz Markowski <[email protected]> Signed-off-by: Kalle Valo <[email protected]>
Gao Feng [Wed, 28 Dec 2016 08:47:42 +0000 (16:47 +0800)]
driver: ipvlan: Remove unnecessary ipvlan NULL check in ipvlan_count_rx
There are three functions which would invoke the ipvlan_count_rx. They
are ipvlan_process_multicast, ipvlan_rcv_frame, and ipvlan_nf_input.
The former two functions already use the ipvlan directly before
ipvlan_count_rx, and ipvlan_nf_input gets the ipvlan from
ipvl_addr->master, it is not possible to be NULL too.
So the ipvlan pointer check is unnecessary in ipvlan_count_rx.
Gao Feng [Wed, 28 Dec 2016 08:46:51 +0000 (16:46 +0800)]
driver: ipvlan: Define common functions to decrease duplicated codes used to add or del IP address
There are some duplicated codes in ipvlan_add_addr6/4 and
ipvlan_del_addr6/4. Now define two common functions ipvlan_add_addr
and ipvlan_del_addr to decrease the duplicated codes.
It could be helful to maintain the codes.
projects / linux.git / log