Linus Torvalds [Fri, 16 Jun 2023 19:27:20 +0000 (12:27 -0700)]
Merge tag 'io_uring-6.4-2023-06-15' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
"A fix for sendmsg with CMSG, and the followup fix discussed for
avoiding touching task->worker_private after the worker has started
exiting"
* tag 'io_uring-6.4-2023-06-15' of git://git.kernel.dk/linux:
io_uring/io-wq: clear current->worker_private on exit
io_uring/net: save msghdr->msg_control for retries
Linus Torvalds [Fri, 16 Jun 2023 19:18:35 +0000 (12:18 -0700)]
Merge tag 'sound-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few small fixes. The only change to the core code is for a
minor race in ALSA OSS sequencer, and the rest are all device-specific
fixes (regression fixes and a usual quirk)"
* tag 'sound-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk flag for HEM devices to enable native DSD playback
ALSA: usb-audio: Fix broken resume due to UAC3 power state
ALSA: seq: oss: Fix racy open/close of MIDI devices
ASoC: tegra: Fix Master Volume Control
ALSA: hda/realtek: Add a quirk for Compaq N14JP6
firmware: cs_dsp: Log correct region name in bin error messages
Lee Jones [Wed, 14 Jun 2023 16:38:54 +0000 (17:38 +0100)]
x86/mm: Avoid using set_pgd() outside of real PGD pages
KPTI keeps around two PGDs: one for userspace and another for the
kernel. Among other things, set_pgd() contains infrastructure to
ensure that updates to the kernel PGD are reflected in the user PGD
as well.
One side-effect of this is that set_pgd() expects to be passed whole
pages. Unfortunately, init_trampoline_kaslr() passes in a single entry:
'trampoline_pgd_entry'.
When KPTI is on, set_pgd() will update 'trampoline_pgd_entry' (an
8-Byte globally stored [.bss] variable) and will then proceed to
replicate that value into the non-existent neighboring user page
(located +4k away), leading to the corruption of other global [.bss]
stored variables.
Fix it by directly assigning 'trampoline_pgd_entry' and avoiding
set_pgd().
Thomas Gleixner [Thu, 15 Jun 2023 09:18:30 +0000 (11:18 +0200)]
tick/common: Align tick period during sched_timer setup
The tick period is aligned very early while the first clock_event_device is
registered. At that point the system runs in periodic mode and switches
later to one-shot mode if possible.
The next wake-up event is programmed based on the aligned value
(tick_next_period) but the delta value, that is used to program the
clock_event_device, is computed based on ktime_get().
With the subtracted offset, the device fires earlier than the exact time
frame. With a large enough offset the system programs the timer for the
next wake-up and the remaining time left is too small to make any boot
progress. The system hangs.
Move the alignment later to the setup of tick_sched timer. At this point
the system switches to oneshot mode and a high resolution clocksource is
available. At this point it is safe to align tick_next_period because
ktime_get() will now return accurate (not jiffies based) time.
Linus Torvalds [Fri, 16 Jun 2023 18:27:34 +0000 (11:27 -0700)]
Merge tag 'riscv-for-linus-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fix from Palmer Dabbelt:
- A documentation patch describing how we use patchwork
* tag 'riscv-for-linus-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
Documentation: RISC-V: patch-acceptance: mention patchwork's role
Omar Sandoval [Tue, 13 Jun 2023 21:14:56 +0000 (14:14 -0700)]
x86/unwind/orc: Add ELF section with ORC version identifier
Commits ffb1b4a41016 ("x86/unwind/orc: Add 'signal' field to ORC
metadata") and fb799447ae29 ("x86,objtool: Split UNWIND_HINT_EMPTY in
two") changed the ORC format. Although ORC is internal to the kernel,
it's the only way for external tools to get reliable kernel stack traces
on x86-64. In particular, the drgn debugger [1] uses ORC for stack
unwinding, and these format changes broke it [2]. As the drgn
maintainer, I don't care how often or how much the kernel changes the
ORC format as long as I have a way to detect the change.
It suffices to store a version identifier in the vmlinux and kernel
module ELF files (to use when parsing ORC sections from ELF), and in
kernel memory (to use when parsing ORC from a core dump+symbol table).
Rather than hard-coding a version number that needs to be manually
bumped, Peterz suggested hashing the definitions from orc_types.h. If
there is a format change that isn't caught by this, the hashing script
can be updated.
This patch adds an .orc_header allocated ELF section containing the
20-byte hash to vmlinux and kernel modules, along with the corresponding
__start_orc_header and __stop_orc_header symbols in vmlinux.
Marc Zyngier [Fri, 16 Jun 2023 11:48:31 +0000 (12:48 +0100)]
perf/core: Drop __weak attribute from arch_perf_update_userpage() prototype
Reiji reports that the arm64 implementation of arch_perf_update_userpage()
is now ignored and replaced by the dummy stub in core code.
This seems to happen since the PMUv3 driver was moved to driver/perf.
As it turns out, dropping the __weak attribute from the *prototype*
of the function solves the problem. You're right, this doesn't seem
to make much sense. And yet... It appears that both symbols get
flagged as weak, and that the first one to appear in the link order
wins:
$ nm drivers/perf/arm_pmuv3.o|grep arch_perf_update_userpage 0000000000001db0 W arch_perf_update_userpage
Dropping the attribute from the prototype restores the expected
behaviour, and arm64 is able to enjoy arch_perf_update_userpage()
again.
In eiointc_resume(), the irq_data passed into eiointc_set_irq_affinity()
should be matched to EIOINTC domain instead of PCH PIC or PCH PCI MSI
domain, so fix it.
Yinbo Zhu [Wed, 14 Jun 2023 11:59:35 +0000 (19:59 +0800)]
irqchip/loongson-liointc: Add IRQCHIP_SKIP_SET_WAKE flag
LIOINTC doesn't require specific logic to work with wakeup IRQs,
and no irq_set_wake callback is needed. To allow registered IRQs
from LIOINTC to be used as a wakeup-source, and ensure irq_set_irq_wake()
works well, the flag IRQCHIP_SKIP_SET_WAKE should be added.
For the INT_POLARITY register of Loongson-2K series IRQ
controller, '0' indicates high level or rising edge triggered,
'1' indicates low level or falling edge triggered, and we
can find out the information from the Loongson 2K1000LA User
Manual v1.0, Table 9-2, Section 9.3 (中断寄存器描述 / Description
of the Interrupt Registers).
For Loongson-3 CPU series, setting INT_POLARITY register is not
supported and writting it has no effect.
So trigger polarity setting shouled be fixed for Loongson-2K CPU
series.
In DeviceTree path, when ht_vec_base is not zero, the hwirq of PCH PIC
will be assigned incorrectly. Because when pch_pic_domain_translate()
adds the ht_vec_base to hwirq, the hwirq does not have the ht_vec_base
subtracted when calling irq_domain_set_info().
The ht_vec_base is designed for the parent irq chip/domain of the PCH PIC.
It seems not proper to deal this in callbacks of the PCH PIC domain and
let's put this back like the initial commit ef8c01eb64ca ("irqchip: Add
Loongson PCH PIC controller").
Jianmin Lv [Wed, 14 Jun 2023 11:59:32 +0000 (19:59 +0800)]
irqchip/loongson-pch-pic: Fix initialization of HT vector register
In an ACPI-based dual-bridge system, IRQ of each bridge's
PCH PIC sent to CPU is always a zero-based number, which
means that the IRQ on PCH PIC of each bridge is mapped into
vector range from 0 to 63 of upstream irqchip(e.g. EIOINTC).
For example, the IRQ vector number of sata controller on
PCH PIC of each bridge is 16, which is sent to upstream
irqchip of EIOINTC when an interrupt occurs, which will set
bit 16 of EIOINTC. Since hwirq of 16 on EIOINTC has been
mapped to a irq_desc for sata controller during hierarchy
irq allocation, the related mapped IRQ will be found through
irq_resolve_mapping() in the IRQ domain of EIOINTC.
So, the IRQ number set in HT vector register should be fixed
to be a zero-based number.
xfrm: Linearize the skb after offloading if needed.
With offloading enabled, esp_xmit() gets invoked very late, from within
validate_xmit_xfrm() which is after validate_xmit_skb() validates and
linearizes the skb if the underlying device does not support fragments.
esp_output_tail() may add a fragment to the skb while adding the auth
tag/ IV. Devices without the proper support will then send skb->data
points to with the correct length so the packet will have garbage at the
end. A pcap sniffer will claim that the proper data has been sent since
it parses the skb properly.
It is not affected with INET_ESP_OFFLOAD disabled.
Linearize the skb after offloading if the sending hardware requires it.
It was tested on v4, v6 has been adopted.
Fixes: 7785bba299a8d ("esp: Add a software GRO codepath") Signed-off-by: Sebastian Andrzej Siewior <[email protected]> Signed-off-by: Steffen Klassert <[email protected]>
Takashi Iwai [Fri, 16 Jun 2023 07:28:27 +0000 (09:28 +0200)]
Merge tag 'asoc-fix-v6.4-rc6-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.4
A couple more fixes for v6.4, one fixing a misleading error log and
another stopping us seeing spurious failures setting the master volume
on some Tegra systems introduced by a change to how we calculate delay
times.
Lukasz Tyl [Wed, 14 Jun 2023 12:25:24 +0000 (14:25 +0200)]
ALSA: usb-audio: Add quirk flag for HEM devices to enable native DSD playback
This commit adds new DEVICE_FLG with QUIRK_FLAG_DSD_RAW and Vendor Id for
HEM devices which supports native DSD. Prior to this change Linux kernel
was not enabling native DSD playback for HEM devices, and as a result,
DSD audio was being converted to PCM "on the fly". HEM devices,
when connected to the system, would only play audio in PCM format,
even if the source material was in DSD format. With the addition of new
VENDOR_FLG in the quircks.c file, the devices are now correctly
recognized, and raw DSD data is transmitted to the device,
allowing for native DSD playback.
Takashi Iwai [Mon, 12 Jun 2023 13:28:18 +0000 (15:28 +0200)]
ALSA: usb-audio: Fix broken resume due to UAC3 power state
As reported in the bugzilla below, the PM resume of a UAC3 device may
fail due to the incomplete power state change, stuck at D1. The
reason is that the driver expects the full D0 power state change only
at hw_params, while the normal PCM resume procedure doesn't call
hw_params.
For fixing the bug, we add the same power state update to D0 at the
prepare callback, which is certainly called by the resume procedure.
Note that, with this change, the power state change in the hw_params
becomes almost redundant, since snd_usb_hw_params() doesn't touch the
parameters (at least it tires so). But dropping it is still a bit
risky (e.g. we have the media-driver binding), so I leave the D0 power
state change in snd_usb_hw_params() as is for now.
Takashi Iwai [Mon, 12 Jun 2023 12:55:33 +0000 (14:55 +0200)]
ALSA: seq: oss: Fix racy open/close of MIDI devices
Although snd_seq_oss_midi_open() and snd_seq_oss_midi_close() can be
called concurrently from different code paths, we have no proper data
protection against races. Introduce open_mutex to each seq_oss_midi
object for avoiding the races.
====================
Check if FIPS mode is enabled when running selftests
Some test cases from net/tls, net/fcnal-test and net/vrf-xfrm-tests
that rely on cryptographic functions to work and use non-compliant FIPS
algorithms fail in FIPS mode.
In order to allow these tests to pass in a wider set of kernels,
- for net/tls, skip the test variants that use the ChaCha20-Poly1305
and SM4 algorithms, when FIPS mode is enabled;
- for net/fcnal-test, skip the MD5 tests, when FIPS mode is enabled;
- for net/vrf-xfrm-tests, replace the algorithms that are not
FIPS-compliant with compliant ones.
Magali Lemes [Tue, 13 Jun 2023 12:32:22 +0000 (09:32 -0300)]
selftests: net: fcnal-test: check if FIPS mode is enabled
There are some MD5 tests which fail when the kernel is in FIPS mode,
since MD5 is not FIPS compliant. Add a check and only run those tests
if FIPS mode is not enabled.
Magali Lemes [Tue, 13 Jun 2023 12:32:21 +0000 (09:32 -0300)]
selftests: net: vrf-xfrm-tests: change authentication and encryption algos
The vrf-xfrm-tests tests use the hmac(md5) and cbc(des3_ede)
algorithms for performing authentication and encryption, respectively.
This causes the tests to fail when fips=1 is set, since these algorithms
are not allowed in FIPS mode. Therefore, switch from hmac(md5) and
cbc(des3_ede) to hmac(sha1) and cbc(aes), which are FIPS compliant.
Fixes: 3f251d741150 ("selftests: Add tests for vrf and xfrms") Reviewed-by: David Ahern <[email protected]> Signed-off-by: Magali Lemes <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Magali Lemes [Tue, 13 Jun 2023 12:32:20 +0000 (09:32 -0300)]
selftests: net: tls: check if FIPS mode is enabled
TLS selftests use the ChaCha20-Poly1305 and SM4 algorithms, which are not
FIPS compliant. When fips=1, this set of tests fails. Add a check and only
run these tests if not in FIPS mode.
Fixes: 4f336e88a870 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests") Fixes: e506342a03c7 ("selftests/tls: add SM4 GCM/CCM to tls selftests") Reviewed-by: Jakub Kicinski <[email protected]> Signed-off-by: Magali Lemes <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Magali Lemes [Tue, 13 Jun 2023 12:32:19 +0000 (09:32 -0300)]
selftests/harness: allow tests to be skipped during setup
Before executing each test from a fixture, FIXTURE_SETUP is run once.
When SKIP is used in FIXTURE_SETUP, the setup function returns early
but the test still proceeds to run, unless another SKIP macro is used
within the test definition, leading to some code repetition. Therefore,
allow tests to be skipped directly from the setup function.
Linus Torvalds [Fri, 16 Jun 2023 04:11:17 +0000 (21:11 -0700)]
Merge tag 'net-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and netfilter.
Selftests excluded - we have 58 patches and diff of +442/-199, which
isn't really small but perhaps with the exception of the WiFi locking
change it's old(ish) bugs.
We have no known problems with v6.4.
The selftest changes are rather large as MPTCP folks try to apply
Greg's guidance that selftest from torvalds/linux should be able to
run against stable kernels.
Last thing I should call out is the DCCP/UDP-lite deprecation notices.
We are fairly sure those are dead, but if we're wrong reverting them
back in won't be fun.
Current release - regressions:
- wifi:
- cfg80211: fix double lock bug in reg_wdev_chan_valid()
- iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
Current release - new code bugs:
- handshake: remove fput() that causes use-after-free
Previous releases - regressions:
- sched: cls_u32: fix reference counter leak leading to overflow
- sched: cls_api: fix lockup on flushing explicitly created chain
Previous releases - always broken:
- nf_tables: integrate pipapo into commit protocol
- nf_tables: incorrect error path handling with NFT_MSG_NEWRULE, fix
dangling pointer on failure
- ping6: fix send to link-local addresses with VRF
- sched: act_pedit: parse L3 header for L4 offset, the skb may not
have the offset saved
- sched: act_ct: fix promotion of offloaded unreplied tuple
- sched: refuse to destroy an ingress and clsact Qdiscs if there are
lockless change operations in flight
- wifi: mac80211: fix handful of bugs in multi-link operation
- ipvlan: fix bound dev checking for IPv6 l3s mode
- eth: enetc: correct the indexes of highest and 2nd highest TCs
- eth: ice: fix XDP memory leak when NIC is brought up and down
Misc:
- add deprecation notices for UDP-lite and DCCP
- selftests: mptcp: skip tests not supported by old kernels
- sctp: handle invalid error codes without calling BUG()"
* tag 'net-6.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
dccp: Print deprecation notice.
udplite: Print deprecation notice.
octeon_ep: Add missing check for ioremap
selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
net: ethernet: stmicro: stmmac: fix possible memory leak in __stmmac_open
net: tipc: resize nlattr array to correct size
sfc: fix XDP queues mode with legacy IRQ
net: macsec: fix double free of percpu stats
net: lapbether: only support ethernet devices
MAINTAINERS: add reviewers for SMC Sockets
s390/ism: Fix trying to free already-freed IRQ by repeated ism_dev_exit()
net: dsa: felix: fix taprio guard band overflow at 10Mbps with jumbo frames
net/sched: cls_api: Fix lockup on flushing explicitly created chain
ice: Fix ice module unload
net/handshake: remove fput() that causes use-after-free
selftests: forwarding: hw_stats_l3: Set addrgenmode in a separate step
net/sched: qdisc_destroy() old ingress and clsact Qdiscs before grafting
net/sched: Refactor qdisc_graft() for ingress and clsact Qdiscs
net/sched: act_ct: Fix promotion of offloaded unreplied tuple
wifi: iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
...
Linus Torvalds [Fri, 16 Jun 2023 03:19:21 +0000 (20:19 -0700)]
Merge tag 'for-6.4/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM thinp discard performance regression introduced during this
merge window where DM core was splitting large discards every 128K
(max_sectors_kb) rather than every 64M (discard_max_bytes).
- Extend DM core LOCKFS fix, made during 6.4 merge, to also fix race
between do_mount and dm's do_suspend (in addition to the earlier
fix's do_mount race with dm's do_resume).
- Fix DM thin metadata operations to first check if the thin-pool is in
"fail_io" mode; otherwise UAF can occur.
- Fix DM thinp's call to __blkdev_issue_discard to use GFP_NOIO rather
than GFP_NOWAIT (__blkdev_issue_discard cannot handle NULL return
from bio_alloc).
* tag 'for-6.4/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: use op specific max_sectors when splitting abnormal io
dm thin: fix issue_discard to pass GFP_NOIO to __blkdev_issue_discard
dm thin metadata: check fail_io before using data_sm
dm: don't lock fs when the map is NULL during suspend or resume
Linus Torvalds [Fri, 16 Jun 2023 03:13:56 +0000 (20:13 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is an unusually large bunch of bug fixes for the later rc cycle,
rxe and mlx5 both dumped a lot of things at once. rxe continues to fix
itself, and mlx5 is fixing a bunch of "queue counters" related bugs.
There is one highly notable bug fix regarding the qkey. This small
security check was missed in the original 2005 implementation and it
allows some significant issues.
Summary:
- Two rtrs bug fixes for error unwind bugs
- Several rxe bug fixes:
* Incorrect Rx packet validation
* Using memory without a refcount
* Syzkaller found use before initialization
* Regression fix for missing locking with the tasklet conversion
from this merge window
- Have bnxt report the correct link properties to userspace, this was
a regression in v6.3
- Several mlx5 bug fixes:
* Kernel crash triggerable by userspace for the RAW ethernet
profile
* Defend against steering refcounting issues created by userspace
* Incorrect change of QP port affinity parameters in some LAG
configurations
- Fix mlx5 Q counters:
* Do not over allocate Q counters to allow userspace to use the
full port capacity
* Kernel crash triggered by eswitch due to mis-use of Q counters
* Incorrect mlx5_device for Q counters in some LAG configurations
- Properly implement the IBA spec restricting privileged qkeys to
root
- Always an error when reading from a disassociated device's event
queue
- isert bug fixes:
* Avoid a deadlock with the CM handler and CM ID destruction
* Correct list corruption due to incorrect locking
* Fix a use after free around connection tear down"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/rxe: Fix rxe_cq_post
IB/isert: Fix incorrect release of isert connection
IB/isert: Fix possible list corruption in CMA handler
IB/isert: Fix dead lock in ib_isert
RDMA/mlx5: Fix affinity assignment
IB/uverbs: Fix to consider event queue closing also upon non-blocking mode
RDMA/uverbs: Restrict usage of privileged QKEYs
RDMA/cma: Always set static rate to 0 for RoCE
RDMA/mlx5: Fix Q-counters query in LAG mode
RDMA/mlx5: Remove vport Q-counters dependency on normal Q-counters
RDMA/mlx5: Fix Q-counters per vport allocation
RDMA/mlx5: Create an indirect flow table for steering anchor
RDMA/mlx5: Initiate dropless RQ for RAW Ethernet functions
RDMA/rxe: Fix the use-before-initialization error of resp_pkts
RDMA/bnxt_re: Fix reporting active_{speed,width} attributes
RDMA/rxe: Fix ref count error in check_rkey()
RDMA/rxe: Fix packet length checks
RDMA/rtrs: Fix rxe_dealloc_pd warning
RDMA/rtrs: Fix the last iu->buf leak in err path
Linus Torvalds [Fri, 16 Jun 2023 03:03:15 +0000 (20:03 -0700)]
Merge tag 'spi-fix-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few more driver specific fixes.
The DesignWare fix is for an issue introduced by conversion to the
chip select accessor functions and is pretty important but the other
two are less severe"
* tag 'spi-fix-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dw: Replace incorrect spi_get_chipselect with set
spi: fsl-dspi: avoid SCK glitches with continuous transfers
spi: cadence-quadspi: Add missing check for dma_set_mask
Linus Torvalds [Fri, 16 Jun 2023 02:54:58 +0000 (19:54 -0700)]
Merge tag 'regulator-fix-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"The set of regulators described for the Qualcomm PM8550 just seems to
have been completely wrong and would likely not have worked at all if
anything tried to actually configure anything except for enabling and
disabling at runtime"
* tag 'regulator-fix-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: Fix regulators for PM8550
Linus Torvalds [Fri, 16 Jun 2023 02:50:57 +0000 (19:50 -0700)]
Merge tag 'regmap-fix-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Another fix for the maple tree cache, Takashi noticed that unlike
other caches the maple tree cache didn't check for read only registers
before trying to sync which would result in spurious syncs for read
only registers where we don't have a default.
This was due to the check being open coded in the caches, we now check
in the shared 'does this register need sync' function so that is fixed
for this and future caches"
* tag 'regmap-fix-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache: Don't sync read-only registers
Linus Torvalds [Fri, 16 Jun 2023 02:13:45 +0000 (19:13 -0700)]
Merge tag 'media/v6.4-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A fix for dvb-core to avoid a race condition during DVB board
registration"
* tag 'media/v6.4-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: dvb-core: Fix use-after-free on race condition at dvb_frontend"
Dave Airlie [Thu, 15 Jun 2023 02:22:11 +0000 (12:22 +1000)]
nouveau: fix client work fence deletion race
This seems to have existed for ever but is now more apparant after
commit 9bff18d13473 ("drm/ttm: use per BO cleanup workers")
My analysis: two threads are running, one in the irq signalling the
fence, in dma_fence_signal_timestamp_locked, it has done the
DMA_FENCE_FLAG_SIGNALLED_BIT setting, but hasn't yet reached the
callbacks.
The second thread in nouveau_cli_work_ready, where it sees the fence is
signalled, so then puts the fence, cleanups the object and frees the
work item, which contains the callback.
Thread one goes again and tries to call the callback and causes the
use-after-free.
Proposed fix: lock the fence signalled check in nouveau_cli_work_ready,
so either the callbacks are done or the memory is freed.
Dave Airlie [Thu, 15 Jun 2023 23:08:13 +0000 (09:08 +1000)]
Merge tag 'amd-drm-fixes-6.4-2023-06-14' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.4-2023-06-14:
amdgpu:
- GFX9 preemption fixes
- Add missing radeon secondary PCI ID
- vblflash fixes
- SMU 13 fix
- VCN 4.0 fix
- Re-enable TOPDOWN flag for large BAR systems to fix regression
- eDP fix
- PSR hang fix
- DPIA fix
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: drop the call to ext4_error() from ext4_get_group_info()
Revert "ext4: remove unnecessary check in ext4_bg_num_gdb_nometa"
Linus Torvalds [Thu, 15 Jun 2023 22:24:33 +0000 (15:24 -0700)]
Merge tag '6.4-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
"Eight, mostly small, smb3 client fixes:
- important fix for deferred close oops (race with unmount) found
with xfstest generic/098 to some servers
- important reconnect fix
- fix problem with max_credits mount option
- two multichannel (interface related) fixes
- one trivial removal of confusing comment
- two small debugging improvements (to better spot crediting
problems)"
* tag '6.4-rc6-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: add a warning when the in-flight count goes negative
cifs: fix lease break oops in xfstest generic/098
cifs: fix max_credits implementation
cifs: fix sockaddr comparison in iface_cmp
smb/client: print "Unknown" instead of bogus link speed value
cifs: print all credit counters in DebugData
cifs: fix status checks in cifs_tree_connect
smb: remove obsolete comment
DCCP was marked as Orphan in the MAINTAINERS entry 2 years ago in commit 054c4610bd05 ("MAINTAINERS: dccp: move Gerrit Renker to CREDITS"). It says
we haven't heard from the maintainer for five years, so DCCP is not well
maintained for 7 years now.
Recently DCCP only receives updates for bugs, and major distros disable it
by default.
Removing DCCP would allow for better organisation of TCP fields to reduce
the number of cache lines hit in the fast path.
Let's add a deprecation notice when DCCP socket is created and schedule its
removal to 2025.
Recently syzkaller reported a 7-year-old null-ptr-deref [0] that occurs
when a UDP-Lite socket tries to allocate a buffer under memory pressure.
Someone should have stumbled on the bug much earlier if UDP-Lite had been
used in a real app. Also, we do not always need a large UDP-Lite workload
to hit the bug since UDP and UDP-Lite share the same memory accounting
limit.
Removing UDP-Lite would simplify UDP code removing a bunch of conditionals
in fast path.
Let's add a deprecation notice when UDP-Lite socket is created and schedule
its removal to 2025.
Alex Maftei [Thu, 15 Jun 2023 08:34:04 +0000 (09:34 +0100)]
selftests/ptp: Fix timestamp printf format for PTP_SYS_OFFSET
Previously, timestamps were printed using "%lld.%u" which is incorrect
for nanosecond values lower than 100,000,000 as they're fractional
digits, therefore leading zeros are meaningful.
This patch changes the format strings to "%lld.%09u" in order to add
leading zeros to the nanosecond value.
Fixes: 568ebc5985f5 ("ptp: add the PTP_SYS_OFFSET ioctl to the testptp program") Fixes: 4ec54f95736f ("ptp: Fix compiler warnings in the testptp utility") Fixes: 6ab0e475f1f3 ("Documentation: fix misc. warnings") Signed-off-by: Alex Maftei <[email protected]> Acked-by: Richard Cochran <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
net: ethernet: stmicro: stmmac: fix possible memory leak in __stmmac_open
Fix a possible memory leak in __stmmac_open when stmmac_init_phy fails.
It's also needed to free everything allocated by stmmac_setup_dma_desc
and not just the dma_conf struct.
Drop free_dma_desc_resources from __stmmac_open and correctly call
free_dma_desc_resources on each user of __stmmac_open on error.
Lin Ma [Wed, 14 Jun 2023 12:06:04 +0000 (20:06 +0800)]
net: tipc: resize nlattr array to correct size
According to nla_parse_nested_deprecated(), the tb[] is supposed to the
destination array with maxtype+1 elements. In current
tipc_nl_media_get() and __tipc_nl_media_set(), a larger array is used
which is unnecessary. This patch resize them to a proper size.
Mike Snitzer [Thu, 15 Jun 2023 01:47:46 +0000 (21:47 -0400)]
dm: use op specific max_sectors when splitting abnormal io
Split abnormal IO in terms of the corresponding operation specific
max_sectors (max_discard_sectors, max_secure_erase_sectors or
max_write_zeroes_sectors).
This fixes a significant dm-thinp discard performance regression that
was introduced with commit e2dd8aca2d76 ("dm bio prison v1: improve
concurrent IO performance"). Relative to discard: max_discard_sectors
is used instead of max_sectors; which fixes excessive discard splitting
(e.g. max_sectors=128K vs max_discard_sectors=64M).
Tested by discarding an 1 Petabyte dm-thin device:
lvcreate -V 1125899906842624B -T test/pool -n thin
time blkdiscard /dev/test/thin
Before this fix (splitting discards every 128K): ~116m
After this fix (splitting discards every 64M) : 0m33.460s
Reported-by: Zorro Lang <[email protected]> Fixes: 06961c487a33 ("dm: split discards further if target sets max_discard_granularity")
Requires: 13f6facf3fae ("dm: allow targets to require splitting WRITE_ZEROES and SECURE_ERASE") Fixes: e2dd8aca2d76 ("dm bio prison v1: improve concurrent IO performance") Signed-off-by: Mike Snitzer <[email protected]>
Mike Snitzer [Wed, 14 Jun 2023 00:05:34 +0000 (20:05 -0400)]
dm thin: fix issue_discard to pass GFP_NOIO to __blkdev_issue_discard
issue_discard() passes GFP_NOWAIT to __blkdev_issue_discard() despite
its code assuming bio_alloc() always succeeds.
Commit 3dba53a958a75 ("dm thin: use __blkdev_issue_discard for async
discard support") clearly shows where things went bad:
Before commit 3dba53a958a75, dm-thin.c's open-coded
__blkdev_issue_discard_async() properly handled using GFP_NOWAIT.
Unfortunately __blkdev_issue_discard() doesn't and it was missed
during review.
As shown above, if dm_pool_commit_metadata() and
dm_pool_abort_metadata() fail in pool_message process, kworker may
trigger UAF.
Fixes: be500ed721a6 ("dm space maps: improve performance with inc/dec on ranges of blocks") Cc: [email protected] Signed-off-by: Li Lingfeng <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
Li Lingfeng [Thu, 1 Jun 2023 06:14:23 +0000 (14:14 +0800)]
dm: don't lock fs when the map is NULL during suspend or resume
As described in commit 38d11da522aa ("dm: don't lock fs when the map is
NULL in process of resume"), a deadlock may be triggered between
do_resume() and do_mount().
This commit preserves the fix from commit 38d11da522aa but moves it to
where it also serves to fix a similar deadlock between do_suspend()
and do_mount(). It does so, if the active map is NULL, by clearing
DM_SUSPEND_LOCKFS_FLAG in dm_suspend() which is called by both
do_suspend() and do_resume().
Fixes: 38d11da522aa ("dm: don't lock fs when the map is NULL in process of resume") Signed-off-by: Li Lingfeng <[email protected]> Signed-off-by: Mike Snitzer <[email protected]>
Since commit 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel
TCC library") intel_soc_dts_iosf is reporting the wrong temperature.
The driver expects tj_max to be in milli-degrees-celcius but after
the switch to the TCC library this is now in degrees celcius so
instead of e.g. 90000 it is set to 90 causing a temperature 45
degrees below tj_max to be reported as -44910 milli-degrees
instead of as 45000 milli-degrees.
ACPI: sleep: Avoid breaking S3 wakeup due to might_sleep()
The addition of might_sleep() to down_timeout() caused the latter to
enable interrupts unconditionally in some cases, which in turn broke
the ACPI S3 wakeup path in acpi_suspend_enter(), where down_timeout()
is called by acpi_disable_all_gpes() via acpi_ut_acquire_mutex().
Namely, if CONFIG_DEBUG_ATOMIC_SLEEP is set, might_sleep() causes
might_resched() to be used and if CONFIG_PREEMPT_VOLUNTARY is set,
this triggers __cond_resched() which may call preempt_schedule_common(),
so __schedule() gets invoked and it ends up with enabled interrupts (in
the prev == next case).
Now, enabling interrupts early in the S3 wakeup path causes the kernel
to crash.
Address this by modifying acpi_suspend_enter() to disable GPEs without
attempting to acquire the sleeping lock which is not needed in that code
path anyway.
Fixes: 99409b935c9a ("locking/semaphore: Add might_sleep() to down_*() family") Reported-by: Srinivas Pandruvada <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]> Acked-by: Peter Zijlstra (Intel) <[email protected]> Cc: 5.15+ <[email protected]> # 5.15+
Neil Armstrong [Thu, 15 Jun 2023 12:51:45 +0000 (14:51 +0200)]
spi: spi-geni-qcom: correctly handle -EPROBE_DEFER from dma_request_chan()
Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.
Íñigo Huguet [Tue, 13 Jun 2023 13:38:54 +0000 (15:38 +0200)]
sfc: fix XDP queues mode with legacy IRQ
In systems without MSI-X capabilities, xdp_txq_queues_mode is calculated
in efx_allocate_msix_channels, but when enabling MSI-X fails, it was not
changed to a proper default value. This was leading to the driver
thinking that it has dedicated XDP queues, when it didn't.
Fix it by setting xdp_txq_queues_mode to the correct value if the driver
fallbacks to MSI or legacy IRQ mode. The correct value is
EFX_XDP_TX_QUEUES_BORROWED because there are no XDP dedicated queues.
The issue can be easily visible if the kernel is started with pci=nomsi,
then a call trace is shown. It is not shown only with sfc's modparam
interrupt_mode=2. Call trace example:
WARNING: CPU: 2 PID: 663 at drivers/net/ethernet/sfc/efx_channels.c:828 efx_set_xdp_channels+0x124/0x260 [sfc]
[...skip...]
Call Trace:
<TASK>
efx_set_channels+0x5c/0xc0 [sfc]
efx_probe_nic+0x9b/0x15a [sfc]
efx_probe_all+0x10/0x1a2 [sfc]
efx_pci_probe_main+0x12/0x156 [sfc]
efx_pci_probe_post_io+0x18/0x103 [sfc]
efx_pci_probe.cold+0x154/0x257 [sfc]
local_pci_probe+0x42/0x80
Fedor Pchelkin [Tue, 13 Jun 2023 19:22:20 +0000 (22:22 +0300)]
net: macsec: fix double free of percpu stats
Inside macsec_add_dev() we free percpu macsec->secy.tx_sc.stats and
macsec->stats on some of the memory allocation failure paths. However, the
net_device is already registered to that moment: in macsec_newlink(), just
before calling macsec_add_dev(). This means that during unregister process
its priv_destructor - macsec_free_netdev() - will be called and will free
the stats again.
Remove freeing percpu stats inside macsec_add_dev() because
macsec_free_netdev() will correctly free the already allocated ones. The
pointers to unallocated stats stay NULL, and free_percpu() treats that
correctly.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 0a28bfd4971f ("net/macsec: Add MACsec skb_metadata_dst Tx Data path support") Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Fedor Pchelkin <[email protected]> Reviewed-by: Sabrina Dubroca <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jan Karcher [Wed, 14 Jun 2023 06:54:56 +0000 (08:54 +0200)]
MAINTAINERS: add reviewers for SMC Sockets
adding three people from Alibaba as reviewers for SMC.
They are currently working on improving SMC on other architectures than
s390 and help with reviewing patches on top.
Thank you D. Wythe, Tony Lu and Wen Gu for your contributions and
collaboration and welcome on board as reviewers!
Julian Ruess [Tue, 13 Jun 2023 12:25:37 +0000 (14:25 +0200)]
s390/ism: Fix trying to free already-freed IRQ by repeated ism_dev_exit()
This patch prevents the system from crashing when unloading the ISM module.
How to reproduce: Attach an ISM device and execute 'rmmod ism'.
Error-Log:
- Trying to free already-free IRQ 0
- WARNING: CPU: 1 PID: 966 at kernel/irq/manage.c:1890 free_irq+0x140/0x540
After calling ism_dev_exit() for each ISM device in the exit routine,
pci_unregister_driver() will execute ism_remove() for each ISM device.
Because ism_remove() also calls ism_dev_exit(),
free_irq(pci_irq_vector(pdev, 0), ism) is called twice for each ISM
device. This results in a crash with the error
'Trying to free already-free IRQ'.
In the exit routine, it is enough to call pci_unregister_driver()
because it ensures that ism_dev_exit() is called once per
ISM device.
The debugfs_create_dir() returns ERR_PTR in case of an error and the
correct way of checking it is using the IS_ERR_OR_NULL inline function
rather than the simple null comparision. This patch fixes the issue.
Hongchen Zhang [Thu, 15 Jun 2023 06:35:52 +0000 (14:35 +0800)]
LoongArch: Let pmd_present() return true when splitting pmd
When we split a pmd into ptes, pmd_present() and pmd_trans_huge() should
return true, otherwise it would be treated as a swap pmd.
This is the same as arm64 does in commit b65399f6111b ("arm64/mm: Change
THP helpers to comply with generic MM semantics"), we also add a new bit
named _PAGE_PRESENT_INVALID for LoongArch.
Vladimir Oltean [Tue, 13 Jun 2023 17:09:07 +0000 (20:09 +0300)]
net: dsa: felix: fix taprio guard band overflow at 10Mbps with jumbo frames
The DEV_MAC_MAXLEN_CFG register contains a 16-bit value - up to 65535.
Plus 2 * VLAN_HLEN (4), that is up to 65543.
The picos_per_byte variable is the largest when "speed" is lowest -
SPEED_10 = 10. In that case it is (1000000L * 8) / 10 = 800000.
Their product - 52434400000 - exceeds 32 bits, which is a problem,
because apparently, a multiplication between two 32-bit factors is
evaluated as 32-bit before being assigned to a 64-bit variable.
In fact it's a problem for any MTU value larger than 5368.
Cast one of the factors of the multiplication to u64 to force the
multiplication to take place on 64 bits.
Vlad Buslov [Mon, 12 Jun 2023 09:34:26 +0000 (11:34 +0200)]
net/sched: cls_api: Fix lockup on flushing explicitly created chain
Mingshuai Ren reports:
When a new chain is added by using tc, one soft lockup alarm will be
generated after delete the prio 0 filter of the chain. To reproduce
the problem, perform the following steps:
(1) tc qdisc add dev eth0 root handle 1: htb default 1
(2) tc chain add dev eth0
(3) tc filter del dev eth0 chain 0 parent 1: prio 0
(4) tc filter add dev eth0 chain 0 parent 1:
Fix the issue by accounting for additional reference to chains that are
explicitly created by RTM_NEWCHAIN message as opposed to implicitly by
RTM_NEWTFILTER message.
Jakub Buchocki [Mon, 12 Jun 2023 17:14:21 +0000 (10:14 -0700)]
ice: Fix ice module unload
Clearing the interrupt scheme before PFR reset,
during the removal routine, could cause the hardware
errors and possibly lead to system reboot, as the PF
reset can cause the interrupt to be generated.
Place the call for PFR reset inside ice_deinit_dev(),
wait until reset and all pending transactions are done,
then call ice_clear_interrupt_scheme().
This introduces a PFR reset to multiple error paths.
Additionally, remove the call for the reset from
ice_load() - it will be a part of ice_unload() now.
Jakub Kicinski [Thu, 15 Jun 2023 05:36:53 +0000 (22:36 -0700)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-06-12 (igc, igb)
This series contains updates to igc and igb drivers.
Husaini clears Tx rings when interface is brought down for igc.
Vinicius disables PTM and PCI busmaster when removing igc driver.
Alex adds error check and path for NVM read error on igb.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igb: fix nvm.ops.read() error handling
igc: Fix possible system crash when loading module
igc: Clean the TX buffer and TX descriptor ring
====================
One can enable CONFIG_NET_HANDSHAKE_KUNIT_TEST config to reproduce above
crash.
The root cause of this bug is that the commit 1ce77c998f04
("net/handshake: Unpin sock->file if a handshake is cancelled") adds one
additional fput() function. That patch claims that the fput() is used to
enable sock->file to be freed even when user space never calls DONE.
However, it seems that the intended DONE routine will never give an
additional fput() of ths sock->file. The existing two of them are just
used to balance the reference added in sockfd_lookup().
This patch revert the mentioned commit to avoid the use-after-free. The
patched kernel could successfully pass the KUNIT test and boot to shell.
[ 0.733613] # Subtest: Handshake API tests
[ 0.734029] 1..11
[ 0.734255] KTAP version 1
[ 0.734542] # Subtest: req_alloc API fuzzing
[ 0.736104] ok 1 handshake_req_alloc NULL proto
[ 0.736114] ok 2 handshake_req_alloc CLASS_NONE
[ 0.736559] ok 3 handshake_req_alloc CLASS_MAX
[ 0.737020] ok 4 handshake_req_alloc no callbacks
[ 0.737488] ok 5 handshake_req_alloc no done callback
[ 0.737988] ok 6 handshake_req_alloc excessive privsize
[ 0.738529] ok 7 handshake_req_alloc all good
[ 0.739036] # req_alloc API fuzzing: pass:7 fail:0 skip:0 total:7
[ 0.739444] ok 1 req_alloc API fuzzing
[ 0.740065] ok 2 req_submit NULL req arg
[ 0.740436] ok 3 req_submit NULL sock arg
[ 0.740834] ok 4 req_submit NULL sock->file
[ 0.741236] ok 5 req_lookup works
[ 0.741621] ok 6 req_submit max pending
[ 0.741974] ok 7 req_submit multiple
[ 0.742382] ok 8 req_cancel before accept
[ 0.742764] ok 9 req_cancel after accept
[ 0.743151] ok 10 req_cancel after done
[ 0.743510] ok 11 req_destroy works
[ 0.743882] # Handshake API tests: pass:11 fail:0 skip:0 total:11
[ 0.744205] # Totals: pass:17 fail:0 skip:0 total:17
Jakub Kicinski [Thu, 15 Jun 2023 04:28:59 +0000 (21:28 -0700)]
Merge tag 'wireless-2023-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
A couple of straggler fixes, mostly in the stack:
- fix fragmentation for multi-link related elements
- fix callback copy/paste error
- fix multi-link locking
- remove double-locking of wiphy mutex
- transmit only on active links, not all
- activate links in the correct order
- don't remove links that weren't added
- disable soft-IRQs for LQ lock in iwlwifi
* tag 'wireless-2023-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: mvm: spin_lock_bh() to fix lockdep regression
wifi: mac80211: fragment per STA profile correctly
wifi: mac80211: Use active_links instead of valid_links in Tx
wifi: cfg80211: remove links only on AP
wifi: mac80211: take lock before setting vif links
wifi: cfg80211: fix link del callback to call correct handler
wifi: mac80211: fix link activation settings order
wifi: cfg80211: fix double lock bug in reg_wdev_chan_valid()
====================
ext4: drop the call to ext4_error() from ext4_get_group_info()
A recent patch added a call to ext4_error() which is problematic since
some callers of the ext4_get_group_info() function may be holding a
spinlock, whereas ext4_error() must never be called in atomic context.
This triggered a report from Syzbot: "BUG: sleeping function called from
invalid context in ext4_update_super" (see the link below).
Therefore, drop the call to ext4_error() from ext4_get_group_info(). In
the meantime use eight characters tabs instead of nine characters ones.
The reverted commit was intended to simpfy the code to get group
descriptor block number in non-meta block group by assuming
s_gdb_count is block number used for all non-meta block group descriptors.
However s_gdb_count is block number used for all meta *and* non-meta
group descriptors. So s_gdb_group will be > actual group descriptor block
number used for all non-meta block group which should be "total non-meta
block group" / "group descriptors per block", e.g. s_first_meta_bg.
Bob Pearson [Tue, 13 Jun 2023 14:43:00 +0000 (09:43 -0500)]
scsi: target: core: Fix error path in target_setup_session()
In the error exits in target_setup_session(), if a branch is taken to
free_sess: transport_free_session() may call to target_free_cmd_counter()
and then fall through to call target_free_cmd_counter() a second time.
This can, and does, sometimes cause seg faults since the data field in
cmd_cnt->refcnt has been freed in the first call.
Fix this problem by simply returning after the call to
transport_free_session(). The second call is redundant for those cases.
The recently added support for command duration limits calls
scsi_report_opcode() four times as each device comes online, which
significantly increases the number of messages logged in a system with many
disks.
Fix the problem by always marking Hyper-V synthetic SCSI devices as not
supporting scsi_report_opcode(). With this setting, the MAINTENANCE_IN SCSI
command is not issued and no messages are logged.
Sagar Biradar [Fri, 19 May 2023 23:08:34 +0000 (16:08 -0700)]
scsi: aacraid: Reply queue mapping to CPUs based on IRQ affinity
Fix the I/O hang that arises because of the MSIx vector not having a mapped
online CPU upon receiving completion.
SCSI cmds take the blk_mq route, which is setup during init. Reserved cmds
fetch the vector_no from mq_map after init is complete. Before init, they
have to use 0 - as per the norm.
Revert "media: dvb-core: Fix use-after-free on race condition at dvb_frontend"
As reported by Thomas Voegtle <[email protected]>, sometimes a DVB card does
not initialize properly booting Linux 6.4-rc4. This is not always, maybe
in 3 out of 4 attempts.
After double-checking, the root cause seems to be related to the
UAF fix, which is causing a race issue:
Jens Axboe [Wed, 14 Jun 2023 01:26:55 +0000 (19:26 -0600)]
io_uring/io-wq: clear current->worker_private on exit
A recent fix stopped clearing PF_IO_WORKER from current->flags on exit,
which meant that we can now call inc/dec running on the worker after it
has been removed if it ends up scheduling in/out as part of exit.
If this happens after an RCU grace period has passed, then the struct
pointed to by current->worker_private may have been freed, and we can
now be accessing memory that is freed.
Ensure this doesn't happen by clearing the task worker_private field.
Both io_wq_worker_running() and io_wq_worker_sleeping() check this
field before going any further, and we don't need any accounting etc
done after this worker has exited.
Fixes: fd37b884003c ("io_uring/io-wq: don't clear PF_IO_WORKER on exit") Reported-by: Zorro Lang <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
Beau Belgrave [Wed, 14 Jun 2023 16:33:35 +0000 (09:33 -0700)]
selftests/user_events: Adapt dyn_test to non-persist events
Now that user_events does not honor persist events the dynamic_events
file cannot be easily used to test parsing and matching cases.
Update dyn_test to use the direct ABI file instead of dynamic_events so
that we still have testing coverage until persist events and
dynamic_events file integration has been decided.
Beau Belgrave [Wed, 14 Jun 2023 16:33:34 +0000 (09:33 -0700)]
selftests/user_events: Ensure auto cleanup works as expected
User events now auto cleanup upon the last reference put. Update
ftrace_test to ensure this works as expected. Ensure EBUSY delays
while event is being deleted do not cause transient failures by
waiting and re-attempting.
Beau Belgrave [Wed, 14 Jun 2023 16:33:33 +0000 (09:33 -0700)]
tracing/user_events: Add auto cleanup and future persist flag
Currently user events need to be manually deleted via the delete IOCTL
call or via the dynamic_events file. Most operators and processes wish
to have these events auto cleanup when they are no longer used by
anything to prevent them piling without manual maintenance. However,
some operators may not want this, such as pre-registering events via the
dynamic_events tracefs file.
Update user_event_put() to attempt an auto delete of the event if it's
the last reference. The auto delete must run in a work queue to ensure
proper behavior of class->reg() invocations that don't expect the call
to go away from underneath them during the unregister. Add work_struct
to user_event struct to ensure we can do this reliably.
Add a persist flag, that is not yet exposed, to ensure we can toggle
between auto-cleanup and leaving the events existing in the future. When
a non-zero flag is seen during register, return -EINVAL to ensure ABI
is clear for the user processes while we work out the best approach for
persistent events.
Beau Belgrave [Wed, 14 Jun 2023 16:33:32 +0000 (09:33 -0700)]
tracing/user_events: Track refcount consistently via put/get
Various parts of the code today track user_event's refcnt field directly
via a refcount_add/dec. This makes it hard to modify the behavior of the
last reference decrement in all code paths consistently. For example, in
the future we will auto-delete events upon the last reference going
away. This last reference could happen in many places, but we want it to
be consistently handled.
Add user_event_get() and user_event_put() for the add/dec. Update all
places where direct refcounts are being used to utilize these new
functions. In each location pass if event_mutex is locked or not. This
allows us to drop events automatically in future patches clearly. Ensure
when caller states the lock is held, it really is (or is not) held.
Beau Belgrave [Wed, 14 Jun 2023 16:33:31 +0000 (09:33 -0700)]
tracing/user_events: Store register flags on events
Currently we don't have any available flags for user processes to use to
indicate options for user_events. We will soon have a flag to indicate
the event should or should not auto-delete once it's not being used by
anyone.
Add a reg_flags field to user_events and parameters to existing
functions to allow for this in future patches.
Bob Pearson [Mon, 12 Jun 2023 15:50:33 +0000 (10:50 -0500)]
RDMA/rxe: Fix rxe_cq_post
A recent patch replaced a tasklet execution of cq->comp_handler by a
direct call. While this made sense it let changes to cq->notify state be
unprotected and assumed that the cq completion machinery and the ulp done
callbacks were reentrant. The result is that in some cases completion
events can be lost. This patch moves the cq->comp_handler call inside of
the spinlock in rxe_cq_post which solves both issues. This is compatible
with the matching code in the request notify verb.
Beau Belgrave [Thu, 1 Jun 2023 22:49:28 +0000 (15:49 -0700)]
tracing/user_events: Remove user_ns walk for groups
During discussions it was suggested that user_ns is not a good place to
try to attach a tracing namespace. The current code has stubs to enable
that work that are very likely to change and incur a performance cost.
Remove the user_ns walk when creating a group and determining the system
name to use, since it's unlikely user_ns will be used in the future.
sunliming [Tue, 6 Jun 2023 06:20:24 +0000 (14:20 +0800)]
tracing/user_events: Fix the incorrect trace record for empty arguments events
The user_events support events that has empty arguments. But the trace event
is discarded and not really committed when the arguments is empty. Fix this
by not attempting to copy in zero-length data.
sunliming [Mon, 29 May 2023 06:51:10 +0000 (14:51 +0800)]
tracing/user_events: Handle matching arguments that is null from dyn_events
When A registering user event from dyn_events has no argments, it will pass the
matching check, regardless of whether there is a user event with the same name
and arguments. Add the matching check when the arguments of registering user
event is null.
sunliming [Mon, 29 May 2023 03:21:00 +0000 (11:21 +0800)]
tracing/user_events: Prevent same name but different args event
User processes register name_args for events. If the same name but different
args event are registered. The trace outputs of second event are printed
as the first event. This is incorrect.
Return EADDRINUSE back to the user process if the same name but different args
event has being registered.
Qu Wenruo [Wed, 14 Jun 2023 06:49:35 +0000 (14:49 +0800)]
btrfs: scrub: fix a return value overwrite in scrub_stripe()
[RETURN VALUE OVERWRITE]
Inside scrub_stripe(), we would submit all the remaining stripes after
iterating all extents.
But since flush_scrub_stripes() can return error, we need to avoid
overwriting the existing @ret if there is any error.
However the existing check is doing the wrong check:
ret2 = flush_scrub_stripes();
if (!ret2)
ret = ret2;
This would overwrite the existing @ret to 0 as long as the final flush
detects no critical errors.
[FIX]
We should check @ret other than @ret2 in that case.
Fixes: 8eb3dd17eadd ("btrfs: dev-replace: error out if we have unrepaired metadata error during") Reviewed-by: Christoph Hellwig <[email protected]> Signed-off-by: Qu Wenruo <[email protected]> Reviewed-by: David Sterba <[email protected]> Signed-off-by: David Sterba <[email protected]>
Steve French [Sun, 11 Jun 2023 16:23:32 +0000 (11:23 -0500)]
cifs: fix lease break oops in xfstest generic/098
umount can race with lease break so need to check if
tcon->ses->server is still valid to send the lease
break response.
Reviewed-by: Bharath SM <[email protected]> Reviewed-by: Shyam Prasad N <[email protected]> Fixes: 59a556aebc43 ("SMB3: drop reference to cfile before sending oplock break") Signed-off-by: Steve French <[email protected]>
Conor Dooley [Tue, 6 Jun 2023 06:59:19 +0000 (07:59 +0100)]
Documentation: RISC-V: patch-acceptance: mention patchwork's role
Palmer suggested at some point, not sure if it was in one of the
weekly linux-riscv syncs, or a conversation at FOSDEM, that we
should document the role of the automation running on our patchwork
instance plays in patch acceptance.
Add a short note to the patch-acceptance document to that end.
Danielle Ratson [Mon, 12 Jun 2023 14:34:58 +0000 (16:34 +0200)]
selftests: forwarding: hw_stats_l3: Set addrgenmode in a separate step
Setting the IPv6 address generation mode of a net device during its
creation never worked, but after commit b0ad3c179059 ("rtnetlink: call
validate_linkmsg in rtnl_create_link") it explicitly fails [1]. The
failure is caused by the fact that validate_linkmsg() is called before
the net device is registered, when it still does not have an 'inet6_dev'.
Likewise, raising the net device before setting the address generation
mode is meaningless, because by the time the mode is set, the address
has already been generated.
Therefore, fix the test to first create the net device, then set its
IPv6 address generation mode and finally bring it up.
[1]
# ip link add name mydev addrgenmode eui64 type dummy
RTNETLINK answers: Address family not supported by protocol
mmc: meson-gx: remove redundant mmc_request_done() call from irq context
The call to mmc_request_done() can schedule, so it must not be called
from irq context. Wake the irq thread if it needs to be called, and let
its existing logic do its work.
====================
net/sched: Fix race conditions in mini_qdisc_pair_swap()
These 2 patches fix race conditions for ingress and clsact Qdiscs as
reported [1] by syzbot, split out from another [2] series (last 2 patches
of it). Per-patch changelog omitted.
Patch 1 hasn't been touched since last version; I just included
everybody's tag.
Patch 2 bases on patch 6 v1 of [2], with comments and commit log slightly
changed. We also need rtnl_dereference() to load ->qdisc_sleeping since
commit d636fc5dd692 ("net: sched: add rcu annotations around
qdisc->qdisc_sleeping"), so I changed that; please take yet another look,
thanks!
Patch 2 has been tested with the new reproducer Pedro posted [3].
Peilin Ye [Sun, 11 Jun 2023 03:30:25 +0000 (20:30 -0700)]
net/sched: qdisc_destroy() old ingress and clsact Qdiscs before grafting
mini_Qdisc_pair::p_miniq is a double pointer to mini_Qdisc, initialized
in ingress_init() to point to net_device::miniq_ingress. ingress Qdiscs
access this per-net_device pointer in mini_qdisc_pair_swap(). Similar
for clsact Qdiscs and miniq_egress.
Unfortunately, after introducing RTNL-unlocked RTM_{NEW,DEL,GET}TFILTER
requests (thanks Hillf Danton for the hint), when replacing ingress or
clsact Qdiscs, for example, the old Qdisc ("@old") could access the same
miniq_{in,e}gress pointer(s) concurrently with the new Qdisc ("@new"),
causing race conditions [1] including a use-after-free bug in
mini_qdisc_pair_swap() reported by syzbot:
@old and @new should not affect each other. In other words, @old should
never modify miniq_{in,e}gress after @new, and @new should not update
@old's RCU state.
Fixing without changing sch_api.c turned out to be difficult (please
refer to Closes: for discussions). Instead, make sure @new's first call
always happen after @old's last call (in {ingress,clsact}_destroy()) has
finished:
In qdisc_graft(), return -EBUSY if @old has any ongoing filter requests,
and call qdisc_destroy() for @old before grafting @new.
Introduce qdisc_refcount_dec_if_one() as the counterpart of
qdisc_refcount_inc_nz() used for filter requests. Introduce a
non-static version of qdisc_destroy() that does a TCQ_F_BUILTIN check,
just like qdisc_put() etc.
Depends on patch "net/sched: Refactor qdisc_graft() for ingress and
clsact Qdiscs".
[1] To illustrate, the syzkaller reproducer adds ingress Qdiscs under
TC_H_ROOT (no longer possible after commit c7cfbd115001 ("net/sched:
sch_ingress: Only create under TC_H_INGRESS")) on eth0 that has 8
transmission queues:
Thread 1 creates ingress Qdisc A (containing mini Qdisc a1 and a2),
then adds a flower filter X to A.
Thread 2 creates another ingress Qdisc B (containing mini Qdisc b1 and
b2) to replace A, then adds a flower filter Y to B.
Here, B calls mini_qdisc_pair_swap(), pointing eth0->miniq_ingress to
its mini Qdisc, b1. Then, A calls mini_qdisc_pair_swap() again during
ingress_destroy(), setting eth0->miniq_ingress to NULL, so ingress
packets on eth0 will not find filter Y in sch_handle_ingress().
This is just one of the possible consequences of concurrently accessing
miniq_{in,e}gress pointers.
projects / linux.git / log