Systems with AST graphics can have multiple output; typically VGA
plus some other port. Record detected output chips in a bitmask and
initialize each output on its own.
Assume a VGA output by default and use SIL164 and DP501 if available.
For ASTDP assume that it can run in parallel with VGA.
Tested on AST2100.
v3:
* define a macro for each BIT(ast_tx_chip) (Patrik)
v2:
* make VGA/SIL164/DP501 mutually exclusive
Bjorn Andersson [Wed, 1 Jun 2022 23:38:18 +0000 (16:38 -0700)]
drm/bridge: lt9611uxc: Cancel only driver's work
During device remove care needs to be taken that no work is pending
before it removes the underlying DRM bridge etc, but this can be done on
the specific work rather than waiting for the flush of the system-wide
workqueue.
Miaoqian Lin [Wed, 1 Jun 2022 03:39:27 +0000 (07:39 +0400)]
drm/meson: encoder_hdmi: Fix refcount leak in meson_encoder_hdmi_init
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Miaoqian Lin [Wed, 1 Jun 2022 03:39:26 +0000 (07:39 +0400)]
drm/meson: encoder_cvbs: Fix refcount leak in meson_encoder_cvbs_init
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Set new vidrst flag in device info for models that synchronize with
external sources (i.e., BMCs). In modesetting, set the corresponding
bits from the device-info flag.
drm/mgag200: Store maximum resolution and memory bandwidth in device info
The maximum resolution and memory bandwidth are model-specific limits.
Both are used during display-mode validation. Store the values in struct
mgag200_device_info and simplify the validation code.
drm/mgag200: Store HW_BUG_NO_STARTADD flag in device info
Flag devices with broken handling of the startadd field in
struct mgag200_device_info, instead of PCI driver data. This
reduces the driver data to a simple type constant.
Rework mgag200_regs_init() and mgag200_mm_init() into device preinit
and init functions. The preinit function, mgag200_device_preinit(),
requests and maps a device's I/O and video memory. The init function,
mgag200_device_init() initializes the state of struct mga_device.
Splitting the initialization between the two functions is necessary
to perform per-model operations between the two calls, such as reading
the unique revision ID on G200SEs.
drm/mgag200: Move PCI-option setup into model-specific code
Split the PCI code into a single call for each model. G200 and G200SE
each contain a dedicated helper with additional instructions. Noteably,
the G200ER has no code for PCI setup.
In a later patch, the magic numbers should be replaced by descriptive
constants.
drm/mgag200: Remove special case for G200SE with <2 MiB
Remove old test for 32-bit vs 16-bit colors. Prefer 24-bit color depth
on all devices. 32-bit color depth doesn't exist, it should have always
been 24-bit.
G200SE with less than 2 MiB of video memory have defaulted to 16-bit
color depth, as the original revision of the G200SE had only 1.75 MiB
of video memory. Using 16-bit colors enabled XGA resolution. But we
now already limit these devices to VGA resolutions as the memory-bandwith
test assumes 32-bit pixel size. So drop the special case from color-depth
selection.
drm/probe-helper: Default to 640x480 if no EDID on DP
If we're unable to read the EDID for a display because it's corrupt /
bogus / invalid then we'll add a set of standard modes for the
display. Since we have no true information about the connected
display, these modes are essentially guesses but better than nothing.
At the moment, none of the modes returned is marked as preferred, but
the modes are sorted such that the higher resolution modes are listed
first.
When userspace sees these modes presented by the kernel it needs to
figure out which one to pick. At least one userspace, ChromeOS [1]
seems to use the rules (which seem pretty reasonable):
1. Try to pick the first mode marked as preferred.
2. Try to pick the mode which matches the first detailed timing
descriptor in the EDID.
3. If no modes were marked as preferred then pick the first mode.
Unfortunately, userspace's rules combined with what the kernel is
doing causes us to fail section 4.2.2.6 (EDID Corruption Detection) of
the DP 1.4a Link CTS. That test case says that, while it's OK to allow
some implementation-specific fall-back modes if the EDID is bad that
userspace should _default_ to 640x480.
Let's fix this by marking 640x480 as default for DP in the no-EDID
case.
NOTES:
- In the discussion around v3 of this patch [2] there was talk about
solving this in userspace and I even implemented a patch that would
have solved this for ChromeOS, but then the discussion turned back
to solving this in the kernel.
- Also in the discussion of v3 [2] it was requested to limit this
change to just DP since folks were worried that it would break some
subtle corner case on VGA or HDMI.
Douglas Anderson [Tue, 10 May 2022 19:29:44 +0000 (12:29 -0700)]
drm/bridge: parade-ps8640: Handle DP AUX more properly
While it works, for the most part, to assume that the panel has
finished probing when devm_of_dp_aux_populate_ep_devices() returns,
it's a bit fragile. This is talked about at length in commit a1e3667a9835 ("drm/bridge: ti-sn65dsi86: Promote the AUX channel to
its own sub-dev").
When reviewing the ps8640 code, I managed to convince myself that it
was OK not to worry about it there and that maybe it wasn't really
_that_ fragile. However, it turns out that it really is. Simply
hardcoding panel_edp_probe() to return -EPROBE_DEFER was enough to put
the boot process into an infinite loop. I believe this manages to trip
the same issues that we used to trip with the main MSM code where
something about our actions trigger Linux to re-probe previously
deferred devices right away and each time we try again we re-trigger
Linux to re-probe.
Let's fix this using the callback introduced in the patch ("drm/dp:
Callbacks to make it easier for drivers to use DP AUX bus properly").
When using the new callback, we have to be a little careful. The
probe_done() callback is no longer always called in the context of
our probe routine. That means we can't rely on being able to return
-EPROBE_DEFER from it. We re-jigger the order of things a bit to
account for that.
With this change, the device still boots (though obviously the panel
doesn't come up) if I force panel-edp to always return
-EPROBE_DEFER. If I fake it and make the panel probe exactly once it
also works.
Douglas Anderson [Tue, 10 May 2022 19:29:43 +0000 (12:29 -0700)]
drm/bridge: Add devm_drm_bridge_add()
This adds a devm managed version of drm_bridge_add(). Like other
"devm" function listed in drm_bridge.h, this function takes an
explicit "dev" to use for the lifetime management. A few notes:
* In general we have a "struct device" for bridges that makes a good
candidate for where the lifetime matches exactly what we want.
* The "bridge->dev->dev" device appears to be the encoder
device. That's not the right device to use for lifetime management.
Douglas Anderson [Tue, 10 May 2022 19:29:42 +0000 (12:29 -0700)]
drm/dp: Add callbacks to make using DP AUX bus properly easier
As talked about in this patch in the kerneldoc of
of_dp_aux_populate_ep_device() and also in the past in commit a1e3667a9835 ("drm/bridge: ti-sn65dsi86: Promote the AUX channel to
its own sub-dev"), it can be difficult for eDP controller drivers to
know when the panel has finished probing when they're using
of_dp_aux_populate_ep_devices().
The ti-sn65dsi86 driver managed to solve this because it was already
broken up into a bunch of sub-drivers. That means we could solve the
problem there by adding a new sub-driver to get the panel. We could
use the traditional -EPROBE_DEFER retry mechansim to handle the case
where the panel hadn't probed yet.
In parade-ps8640 we didn't really solve this. The code just expects
the panel to be ready right away. While reviewing the code originally
I had managed to convince myself it was fine to just expect the panel
right away, but additional testing has shown that not to be the
case. We could fix parade-ps8640 like we did ti-sn65dsi86 but it's
pretty cumbersome (since we're not already broken into multiple
drivers) and requires a bunch of boilerplate code.
After discussion [1] it seems like the best solution for most people
is:
- Accept that there's always at most one device that will probe as a
result of the DP AUX bus (it may have sub-devices, but there will be
one device _directly_ probed).
- When that device finishes probing, we can just have a call back.
This patch implements that idea. We'll now take a callback as an
argument to the populate function. To make this easier to land in
pieces, we'll make wrappers for the old functions. The functions with
the new name (which make it clear that we only have one child) will
take the callback and the functions with the old name will temporarily
wrap.
drm/gma500: Read EDID from the correct i2c adapter
Someone made the mistake to try reading EDID from the backlight i2c
adapter. This has been wrong for a very long time but since we read out
the modes correctly on init and don't hotplug lvds it has been working
anyway. Correct this by using connector->ddc instead of
encoder->i2c_bus. Both PSB and CDV are affected but this bug.
drm/gma500: Make oaktrail lvds use ddc adapter from drm_connector
We're moving all uses of ddc_bus to drm_connector where they belong.
The initialization of the gma_i2c_chan for Oaktrail is a bit backwards
so it required improvements. Also cleanup the error handling in
oaktrail_lvds_init(). Since this is the last user of
gma_encoder->ddc_bus we can remove it.
drm/gma500: Make psb lvds use ddc adapter from drm_connector
We're moving all uses of ddc_bus to drm_connector where they belong.
Also cleanup the error handling in psb_intel_lvds_init() and remove
unused ddc_bus in psb_intel_lvds_priv.
drm/gma500: Make cdv hdmi use ddc adapter from drm_connector
We're moving all uses of ddc_bus from gma_encoder to drm_connector where
they belong. Also, cleanup the error handling in cdv_hdmi_init()
and remove unused i2c pointer in mid_intel_hdmi_priv.
drm/gma500: Make cdv lvds use ddc adapter from drm_connector
We're moving all uses of ddc_bus to drm_connector where they belong.
Also, add missing call to destroy ddc bus when destroying the connector
and cleanup the error handling in cdv_intel_lvds_init().
drm/ssd130x: Only define a SPI device ID table when built as a module
The kernel test robot reports a compile warning due the ssd130x_spi_table
variable being defined but not used. This happen when ssd130x-spi driver
is built-in instead of being built as a module, i.e:
CC drivers/gpu/drm/solomon/ssd130x-spi.o
AR drivers/base/firmware_loader/built-in.a
AR drivers/base/built-in.a
CC kernel/trace/trace.o
drivers/gpu/drm/solomon/ssd130x-spi.c:155:35: warning: ‘ssd130x_spi_table’ defined but not used [-Wunused-const-variable=]
155 | static const struct spi_device_id ssd130x_spi_table[] = {
| ^~~~~~~~~~~~~~~~~
The driver shouldn't need a SPI device ID table and only have an OF device
ID table, but the former is needed to workaround an issue in the SPI core.
This always reports a MODALIAS of the form "spi:<device>" even for devices
registered through Device Trees.
But the table is only needed when the driver built as a module to populate
the .ko alias info. It's not needed when the driver is built-in the kernel.
Saurabh Sengar [Sat, 21 May 2022 14:23:39 +0000 (07:23 -0700)]
drm/hyperv : Removing the restruction of VRAM allocation with PCI bar size
There were two different approaches getting used in this driver to
allocate vram:
1. VRAM allocation from PCI region for Gen1
2. VRAM alloaction from MMIO region for Gen2
First approach limilts the vram to PCI BAR size, which is 64 MB in most
legacy systems. This limits the maximum resolution to be restricted to
64 MB size, and with recent conclusion on fbdev issue its concluded to have
similar allocation strategy for both Gen1 and Gen2. This patch unifies
the Gen1 and Gen2 vram allocation strategy.
Christian König [Mon, 25 Apr 2022 12:22:12 +0000 (14:22 +0200)]
dma-buf: generalize dma_fence unwrap & merging v3
Introduce a dma_fence_unwrap_merge() macro which allows to unwrap fences
which potentially can be containers as well and then merge them back
together into a flat dma_fence_array.
v2: rename the function, add some more comments about how the wrapper is
used, move filtering of signaled fences into the unwrap iterator,
add complex selftest which covers more cases.
v3: fix signaled fence filtering once more
Yunhao Tian [Tue, 10 May 2022 03:02:19 +0000 (11:02 +0800)]
drm/mipi-dbi: align max_chunk to 2 in spi_transfer
In __spi_validate, there's a validation that no partial transfers
are accepted (xfer->len % w_size must be zero). When
max_chunk is not a multiple of bpw (e.g. max_chunk = 65535,
bpw = 16), the transfer will be rejected.
This patch aligns max_chunk to 2 bytes (the maximum value of bpw is 16),
so that no partial transfer will occur.
Add the features, issues, and GPU ID for Mali-G57, a first-generation
Valhall GPU. Other first- and second-generation Valhall GPUs should be
similar.
v2: Split out issue list for r0p0 from newer Natt GPUs, as TTRX_3485 was
fixed in r0p1. Unfortunately, MT8192 has a r0p0, so we do need to handle
TTRX_3485.
L2_MMU_CONFIG is an implementation-defined register. Different Mali GPUs
define slightly different MAX_READS and MAX_WRITES fields, which
throttle outstanding reads and writes when set to non-zero values. When
left as zero, reads and writes are not throttled.
Both kbase and panfrost always zero these registers. Per discussion with
Steven Price, there are two reasons these quirks may be used:
1. Simulating slower memory subsystems. This use case is only of
interest to system-on-chip designers; it is not relevant to mainline.
2. Working around broken memory subsystems. Hopefully we never see this
case in mainline. If we do, we'll need to set this register based on
an SoC-compatible, rather than generally matching on the GPU model.
To the best of our knowledge, these fields are zero at reset, so the
write is not necessary. Let's remove the write to aid porting to new
Mali GPUs, which have different layouts for the L2_MMU_CONFIG register.
Add the HW_FEATURE_CLEAN_ONLY_SAFE bit based on kbase. When I actually
tried to port the logic from kbase, trivial jobs raised Data Invalid
Faults, so this may depend on other coherency details. It's still useful
to have the bit to record the feature bit when adding new models.
TTRX_3485 requires the infamous "dummy job" workaround. I have this
workaround implemented in a local branch, but I have not yet hit a case
that requires it so I cannot test whether the implementation is correct.
In the mean time, add the quirk bit so we can document which platforms
may need it in the future.
From the kernel's perspective, (pre-CSF, "Job Manager") Valhall is more
or less compatible with Bifrost, although they differ to userspace. Add
a compatible for Valhall to the existing Bifrost bindings documentation.
As the first SoC with a Valhall GPU receiving mainline support, add a
specific compatible for the MediaTek MT8192, which instantiates a
Mali-G57.
v2: Change compatible to arm,mali-valhall-jm (Daniel Stone).
Jonathan Liu [Mon, 23 May 2022 13:01:44 +0000 (23:01 +1000)]
drm: bridge: icn6211: Adjust clock phase using SYS_CTRL_1
The code from [1] sets SYS_CTRL_1 to different values depending on the
desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
positive edge of the clock with the pixel data while other values delay
the clock by a fraction of the clock period. A clock phase of 1/2 aligns
the negative edge of the clock with the pixel data.
The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
aligning the positive edge of the clock with the pixel data. This won't
work correctly for panels that require aligning the negative edge of the
clock with the pixel data.
Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
present in bus_flags, otherwise adjust the clock phase to 1/2 as
appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
Rob Herring [Wed, 25 May 2022 20:56:26 +0000 (15:56 -0500)]
dt-bindings: display: ingenic,jz4780-hdmi: Drop undocumented 'ddc-i2c-bus'
While 'ddc-i2c-bus' is a common property, it should be in a connector
node rather than the HDMI bridge node as the I2C bus goes to a
connector and not the HDMI block. Drop it from the example.
Fabio Estevam [Wed, 25 May 2022 21:53:16 +0000 (18:53 -0300)]
drm: bridge: adv7511: Move CEC definitions to adv7511_cec.c
ADV7511_REG_CEC_RX_FRAME_HDR[] and ADV7511_REG_CEC_RX_FRAME_LEN[]
are only used inside adv7511_cec.c.
Move their definitions to this file to avoid the following build
warnings when CONFIG_DRM_I2C_ADV7511_CEC is not selected:
drivers/gpu/drm/bridge/adv7511/adv7511.h:229:17: warning: 'ADV7511_REG_CEC_RX_FRAME_HDR' defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/bridge/adv7511/adv7511.h:235:17: warning: 'ADV7511_REG_CEC_RX_FRAME_LEN' defined but not used [-Wunused-const-variable=]
Since commit ba420afab565 ("drm/vkms: Bugfix racing hrtimer vblank
handle") the work is scheduled at vkms_vblank_simulate() and since
commit 5ef8100a3919 ("drm/vkms: flush crc workers earlier in commit
flow") the work is flushed at vkms_atomic_commit_tail(). Update function
commment to reflect that.
Gao Chao [Tue, 24 May 2022 02:45:51 +0000 (10:45 +0800)]
drm/panel: Fix build error when CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y && CONFIG_DRM_DISPLAY_HELPER=m
If CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y && CONFIG_DRM_DISPLAY_HELPER=m,
bulding fails:
drivers/gpu/drm/panel/panel-samsung-atna33xc20.o: In function `atana33xc20_probe':
panel-samsung-atna33xc20.c:(.text+0x744): undefined reference to
`drm_panel_dp_aux_backlight'
make: *** [vmlinux] Error 1
Let CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20 select DRM_DISPLAY_DP_HELPER and
CONFIG_DRM_DISPLAY_HELPER to fix this error.
Mark Menzynski [Mon, 23 May 2022 11:35:41 +0000 (13:35 +0200)]
drm/nouveau: clear output poll workers before nouveau_fbcon_destroy()
Resources needed for output poll workers are destroyed in
nouveau_fbcon_fini() before output poll workers are cleared in
nouveau_display_fini(). This means there is a time between fbcon_fini()
and display_fini(), where if output poll happens, it crashes.
This patch introduces another output poll clearing before fbcon
resources are destroyed.
BUG: KASAN: use-after-free in
__drm_fb_helper_initial_config_and_unlock.cold+0x1f3/0x291
[drm_kms_helper]
This patch depends on the patches just aplied to the media tree, and will
not build without them, which leaves drm-misc-next in a broken state.
Let's revert the two latter patches until rc1 has been branched,
and rc1 has been backmerged into drm-misc-next.
This patch depends on the patches just aplied to the media tree, and will
not build without them, which leaves drm-misc-next in a broken state.
Let's revert the two latter patches until rc1 has been branched,
and rc1 has been backmerged into drm-misc-next.
drm/st7735r: Fix module autoloading for Okaya RH128128T
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that the st7735r.ko module won't autoload if
a DT has a node with a compatible "okaya,rh128128t" string.
In that case, kmod expects a "MODALIAS=of:N*T*Cokaya,rh128128t" uevent but
instead will get a "MODALIAS=spi:rh128128t", which is not present in the
list of aliases:
John Stultz [Wed, 11 May 2022 01:26:12 +0000 (01:26 +0000)]
drm/bridge: lt9611: Use both bits for HDMI sensing
In commit 19cf41b64e3b ("lontium-lt9611: check a different
register bit for HDMI sensing"), the bit flag used to detect
HDMI cable connect was switched from BIT(2) to BIT(0) to improve
compatibility with some monitors that didn't seem to set BIT(2).
However, with that change, I've seen occasional issues where the
detection failed, because BIT(2) was set, but not BIT(0).
Unfortunately, as I understand it, the bits and their function
was never clearly documented. So lets instead check both
(BIT(2) | BIT(0)) when checking the register.
drm/i915/display/debug: Expose crtc current bpc via debugfs
This new debugfs will expose the currently using bpc by crtc.
It is very useful for verifying whether we enter the correct
output color depth from IGT.
This patch will also add the connector's max supported bpc to
"i915_display_info" debugfs.
drm/r128: Fix undefined behavior due to shift overflowing the constant
Fix:
drivers/gpu/drm/r128/r128_cce.c: In function ‘r128_do_init_cce’:
drivers/gpu/drm/r128/r128_cce.c:417:2: error: case label does not reduce to an integer constant
case R128_PM4_64BM_64VCBM_64INDBM:
^~~~
drivers/gpu/drm/r128/r128_cce.c:418:2: error: case label does not reduce to an integer constant
case R128_PM4_64PIO_64VCPIO_64INDPIO:
^~~~
See https://lore.kernel.org/r/YkwQ6%[email protected] for the gory
details as to why it triggers with older gccs only.
Marek Vasut [Fri, 20 May 2022 12:15:43 +0000 (14:15 +0200)]
drm/bridge: tc358767: Make sure Refclk clock are enabled
The Refclk may be supplied by SoC clock output instead of crystal
oscillator, make sure the clock are enabled before any other action
is performed with the bridge chip, otherwise it may either fail to
operate at all, or miss reset GPIO toggle.
Douglas Anderson [Tue, 10 May 2022 19:29:41 +0000 (12:29 -0700)]
drm/dp: Export symbol / kerneldoc fixes for DP AUX bus
While working on the DP AUX bus code I found a few small things that
should be fixed. Namely the non-devm version of
of_dp_aux_populate_ep_devices() was missing an export. There was also
an extra blank line in a kerneldoc and a kerneldoc that incorrectly
documented a return value. Fix these.
drm: Document the power requirements for DP AUX transfers
When doing DP AUX transfers there are two actors that need to be
powered in order for the DP AUX transfer to work: the DP source and
the DP sink. Commit bacbab58f09d ("drm: Mention the power state
requirement on side-channel operations") added some documentation
saying that the DP source is required to power itself up (if needed)
to do AUX transfers. However, that commit doesn't talk anything about
the DP sink.
For full fledged DP the sink isn't really a problem. It's expected
that if an external DP monitor isn't plugged in that attempting to do
AUX transfers won't work. It's also expected that if a DP monitor is
plugged in (and thus asserting HPD) then AUX transfers will work.
When we're looking at eDP, however, things are less obvious. Let's add
some documentation about expectations. Here's what we'll say:
1. We don't expect the DP AUX transfer function to power on an eDP
panel. If an eDP panel is physically connected but powered off then it
makes sense for the transfer to fail.
2. We'll document that the official way to power on a panel is via the
bridge chain, specifically by making sure that the panel's prepare
function has been called (which is called by
panel_bridge_pre_enable()). It's already specified in the kernel doc
of drm_panel_prepare() that this is the way to power the panel on and
also that after this call "it is possible to communicate with any
integrated circuitry via a command bus."
3. We'll also document that for code running in the panel driver
itself that it is legal for the panel driver to power itself up
however it wants (it doesn't need to officially call
drm_panel_pre_enable()) and then it can do AUX bus transfers. This is
currently the way that edp-panel works when it's running atop the DP
AUX bus.
NOTE: there was much discussion of all of this in response to v1 [1]
of this patch. A summary of that is:
* With the Intel i195 driver, apparently eDP panels do get powered
up. We won't forbid this but it is expected that code that wants to
run on a variety of platforms should ensure that the drm_panel's
prepare() function has been called.
* There is at least a reasonable amount of agreement that the
transfer() functions itself shouldn't be responsible for powering
the panel. It's proposed that if we need the DP AUX dev nodes to be
robust for eDP that the code handling the DP AUX dev nodes could
handle powering the panel by ensuring that the panel's prepare()
call was made. Potentially drm_dp_aux_dev_get_by_minor() could be a
good place to do this. This is left as a future exercise. Until
that's fixed the DP AUX dev nodes for eDP are probably best just
used for debugging.
* If a panel could be in PSR and DP AUX via the dev node needs to be
reliable then we need to be able to pull the panel out of PSR. On
i915 this is also apparently handled as part of the transfer()
function.
Douglas Anderson [Wed, 11 May 2022 22:58:08 +0000 (15:58 -0700)]
drm/probe-helper: For DP, add 640x480 if all other modes are bad
As per Displayport spec section 5.2.1.2 ("Video Timing Format") says
that all detachable sinks shall support 640x480 @60Hz as a fail safe
mode.
A DP compliance test expected us to utilize the above fact when all
modes it presented to the DP source were not achievable. It presented
only modes that would be achievable with more lanes and/or higher
speeds than we had available and expected that when we couldn't do
that then we'd fall back to 640x480 even though it didn't advertise
this size.
In order to pass the compliance test (and also support any users who
might fall into a similar situation with their display), we need to
add 640x480 into the list of modes. However, we don't want to add
640x480 all the time. Despite the fact that the DP spec says all sinks
_shall support_ 640x480, they're not guaranteed to support it
_well_. Continuing to read the spec you can see that the display is
not required to really treat 640x480 equal to all the other modes. It
doesn't need to scale or anything--just display the pixels somehow for
failsafe purposes. It should also be noted that it's not hard to find
a display hooked up via DisplayPort that _doesn't_ support 640x480 at
all. The HP ZR30w screen I'm sitting in front of has a native DP port
and doesn't work at 640x480. I also plugged in a tiny 800x480 HDMI
display via a DP to HDMI adapter and that screen definitely doesn't
support 640x480.
As a compromise solution, let's only add the 640x480 mode if:
* We're on DP.
* All other modes have been pruned.
This acknowledges that 640x480 might not be the best mode to use but,
since sinks are _supposed_ to support it, we will at least fall back
to it if there's nothing else.
Note that we _don't_ add higher resolution modes like 1024x768 in this
case. We only add those modes for a failed EDID read where we have no
idea what's going on. In the case where we've pruned all modes then
instead we only want 640x480 which is the only defined "Fail Safe"
resolution.
This patch originated in response to Kuogee Hsieh's patch [1].
Douglas Anderson [Wed, 11 May 2022 22:58:07 +0000 (15:58 -0700)]
drm/probe-helper: Add helper for drm_helper_probe_single_connector_modes()
The drm_helper_probe_single_connector_modes() is a bit long. Let's
break a chunk off to update and validate modes. This helps avoid one
goto and also will allow us to more easily call the helper a second
time in a future patch without adding looping or another goto.
This change is intended to be a no-op change--just code movement.
drm/gem-vram: Share code between GEM VRAM's _{prepare, cleanup}_fb()
The error-recovery code in drm_gem_vram_plane_helper_prepare_fb() is of
the same pattern as drm_gem_vram_plane_helper_cleanup_fb(). Implement
both of them using an internal helper. No functional changes.
drm/gem: Ignore color planes that are unused by framebuffer format
Only handle color planes that exist in a framebuffer's color format.
Ignore non-existing planes.
So far, several helpers assumed that all 4 planes are available and
silently ignored non-existing planes. This lead to subtil bugs with
uninitialized data in instances of struct iosys_map. [1]
drm/gem: Share code between drm_gem_fb_{begin,end}_cpu_access()
The error-recovery code in drm_gem_fb_begin() is of the same pattern
as drm_gem_fb_end(). Implement both of them using an internal helper.
No functional changes.
v2:
* print additional information in error message (Javier)
* fix commit description (Javier)
Dongjin Kim [Mon, 16 May 2022 07:22:45 +0000 (07:22 +0000)]
drm/meson: add YUV422 output support
Support YUV422 output from the Amlogic Meson SoC VPU to the HDMI
controller. Without this YUV422 format out of the HDMI encoder
leads to using the dw-hdmi YUV444 to YUV422 color conversion which
gives wrong colors and a green line on the left edge of the screen.
Miaoqian Lin [Wed, 11 May 2022 05:40:51 +0000 (09:40 +0400)]
drm/meson: Fix refcount leak in meson_encoder_hdmi_init
of_find_device_by_node() takes reference, we should use put_device()
to release it when not need anymore.
Add missing put_device() in error path to avoid refcount
leak.
drm/mgag200: Split up connector's mode_valid helper
Split up the connector's mode_valid helper into a simple-pipe and a
mode-config helper. The simple-pipe helper tests for display-size
limits while the mode-config helper tests for memory-bandwidth limits.
Also add the mgag200_ prefix to mga_vga_calculate_mode_bandwidth() and
comment on the function's purpose.
The memory-bandwidth tests assume that the display uses 4 bytes per
pixel. The first models of G200SE-A only had 1.75 MiB of VRAM, which
limits these devices to 640x480-32.
v2:
* note the memory constraints on early G200SE-A
drm/mgag200: Test memory requirements in drm_mode_config_funcs.mode_valid
Test for a mode's memory requirements in the device-wide mode_valid
helper. For simplicify, always assume a 32-bit color format. While
some rejected modes would work with less colors, implementing this
is probably not worth the effort.
Also remove the memory-related test from the connector's mode_valid
helper. The test uses the bpp value that users can specify on the
kernel's command line. This value is unrelated and the test would
belong into atomic_check.
struct mga_connector has outlived its purpose. Inline the rsp init
helper into the mode-config code and remove the data structure. No
functional changes.
Store the I2C state within struct mga_device and switch I2C to
managed release. Simplifies the related code and lets us remove
mga_connector_destroy().
drm/mgag200: Implement connector's get_modes with helper
Provide drm_connector_helper_get_modes_from_ddc() to implement the
connector's get_modes callback. The new helper updates the connector
from DDC-provided EDID data.
Initialization of the I2C adapter was allowed to fail. The mgag200
driver would have continued without DDC support. Had this happened in
practice, it would have led to segmentation faults in the connector
code. Resolve this problem by failing driver initialization on I2C-
related errors.
v2:
* initialize 'ret' before drm_err() (kernel test robot)
DDC operation conflicts with concurrent mode setting. Acquire the
driver's I/O lock in get_modes to prevent this. This change should
have been part of commit 931e3f3a0e99 ("drm/mgag200: Protect
concurrent access to I/O registers with lock"), but apparently got
lost somewhere.
v3:
* fix commit message to say 'drm/mgag200' (Jocelyn)
drm/scheduler: Don't kill jobs in interrupt context
Interrupt context can't sleep. Drivers like Panfrost and MSM are taking
mutex when job is released, and thus, that code can sleep. This results
into "BUG: scheduling while atomic" if locks are contented while job is
freed. There is no good reason for releasing scheduler's jobs in IRQ
context, hence use normal context to fix the trouble.
drm: bridge: DRM_FSL_LDB should depend on ARCH_MXC
The Freescale i.MX8MP LDB bridge is only present on Freescale i.MX8MP
SoCs. Hence add a dependency on ARCH_MXC, to prevent asking the user
about this driver when configuring a kernel without i.MX SoC support.
Marek Vasut [Sat, 30 Apr 2022 02:50:20 +0000 (04:50 +0200)]
drm: bridge: icn6211: Register macro clean up
Drop two unused register macros, ICN6211_MAX_REGISTER and MIPI_ATE_STATUS_1,
neither of which is used and where the later should be specified using macro
MIPI_ATE_STATUS(1) instead. Drop the _(n) underscore and keep only the (n)
part of register macros. No functional change.
Jocelyn Falempe [Fri, 13 May 2022 08:49:00 +0000 (10:49 +0200)]
drm/mgag200: Enable atomic gamma lut update
Add support for atomic update of gamma lut.
With this patch the "Night light" feature of gnome3
is working properly on mgag200.
v2:
- Add a default linear gamma function
- renamed functions with mgag200 prefix
- use format's 4cc code instead of bit depth
- use better interpolation for 16bits gamma
- remove legacy function mga_crtc_load_lut()
- can't remove the call to drm_mode_crtc_set_gamma_size()
because it doesn't work with userspace.
- other small refactors
v3:
- change mgag200_crtc_set_gamma*() argument
to struct drm_format_info *format
- fix printk format to %p4cc for 4cc and %zu for size_t
- rebased to drm-misc-next.
Don't add a mode for the kernel's command-line parameters from
within the DRM client code. Doing so can result in an unusable
display. If there's no compatible command-line mode, the client
will use one of the connector's preferred modes.
All mode creation and validation has to be performed by the
connector. When clients run, the connector's fill_modes callback
has already processed the kernel parameters and validated each
mode before adding it. The connector's mode list does not contain
invalid modes.
When picking a mode, first look for modes that have been specified
by the user on the kernel's command line. Only if that fails, use
the existing heuristic of picking a nearby mode from it's various
parameters.
drm: Always warn if user-defined modes are not supported
Print a warning if a user-specifed display mode is not supported by
the display pipeline. Users specified the display mode on the kernel
command line with the use of the video= parameter. Setting an
unsupported mode will leave the console blank, so we should at least
let the user know why.
projects / linux.git / log