Arnd Bergmann [Tue, 9 Feb 2021 17:05:27 +0000 (18:05 +0100)]
Merge tag 'actions-arm-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions into arm/dt
Actions Semi ARM DT changes for v5.12:
Updates to the existing S500 ARM SoC. Support has been added for CMU (Clock
Management Unit), Reset controller, DMA, Pinctrl/GPIO, MMC, I2C and SIRQ
(interrupt controller). Since the CMU support is added, the dummy fixed clock
used for the UART controller has been removed for all S500 based boards and
proper UART clock from CMU is used.
Added uSD support and I2C pinctrl configuration for Roseapplepi board based on
S500 SoC. This will make the board boot mainline with a distro from uSD card.
The I2C pinctrl config is added specifically for the PMIC which is currently
under review.
* tag 'actions-arm-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions:
arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500: Add SIRQ controller
arm: dts: owl-s500: Add I2C support
arm: dts: owl-s500: Add MMC support
arm: dts: owl-s500: Add pinctrl & GPIO support
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add Reset controller
arm: dts: owl-s500: Set CMU clocks for UARTs
arm: dts: owl-s500: Add Clock Management Unit
Arnd Bergmann [Tue, 9 Feb 2021 17:03:39 +0000 (18:03 +0100)]
Merge tag 'imx-dt64-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.12:
- New board support: Beacon i.MX8M Nano development kit, i.MX8MM Nitrogen,
Gateworks i.MX 8M Mini Development Kits, phyBOARD-Pollux-i.MX8MP,
Librem5 Evergreen.
- Update imx8mm-beacon to drop unused clock-names reference, and add
more pinctrl states for USDHC1.
- Support soc unique ID read with NVMEM on i.MX8M SoCs.
- A series from Biwen Li to add interrupt line for RTC device on
Layerscape SoCs.
- A couple of patch sets to update imx8mq-librem5 support around
regulators, RTC, charger, display, etc.
- A series from Joakim Zhang to improve i.MX8M FEC device configuration.
- A series from Kuldeep Singh to enable flexcan support for LX2160A and
LS1028A.
- A series from Lucas Stach to update ZII devices around audio, USB, I2C
pin configuration and UCS1002 ALERT.
- A series from Michael Walle to update Layerscape device trees to use
constants in the clockgen phandle, add sl28 variant 1 and enable SATA.
- A few patches from Russell King to improve support for a couple of
LX2160A boards.
- A series from Shengjiu Wang to add more audio support for imx8mn-evk.
- Other small and random updates.
* tag 'imx-dt64-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (71 commits)
arm64: dts: imx: Add i.mx8mm nitrogen basic dts support
arm64: dts: zii-rmb3: enable RMI4 reduced reporting
arm64: dts: zii-ultra: only trigger IRQ on falling edge ucs1002 ALERT pin
arm64: dts: zii-ultra: limit USB ports to USB2 speed
arm64: dts: zii-ultra: fix i2c pin configuration
arm64: dts: zii-ultra: add sound support
arm64: dts: ls1028a: Enable flexcan support for LS1028A-RDB/QDS
arm64: dts: ls1028a: Update flexcan properties
arm64: dts: lx2160a: Add flexcan support
arm64: dts: fsl-ls1012a-frdm: add spi-uart device
arm64: dts: fsl-ls1012a-rdb: add i2c devices
arm64: dts: imx8mn-beacon-som: Enable QSPI on SOM
arm64: dts: imx8mn: Add fspi node
arm64: dts: Add Librem5 Evergreen
arm64: dts: imx8mq-librem5: set regulators boot-on
arm64: dts: imx8mq-librem5: enable the LCD panel
arm64: dts: imx8mq-librem5: Add LCD_1V8 regulator
arm64: dts: imx8mq-librem5: Add usb-c chip as supplier for the charger
arm64: dts: imx8mq-librem5: Don't mark buck3 as always on
arm64: dts: imx8mq-librem5: Mark charger IRQ as High-Z
...
Arnd Bergmann [Tue, 9 Feb 2021 17:01:41 +0000 (18:01 +0100)]
Merge tag 'imx-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree change for 5.12:
- A series from Oleksij Rempel to add i.MX6 based Plymovent, Protonic
and Kverneland boards.
- A series from Andreas Kemnade to improve UART support for ebook
readers.
- A series from Fabio Estevam to update imx6ul-14x14-evk device tree for
adding GPIO expander and camera support.
- A patch set from Lucas Stach to improve ZII RDU2 support, enabling
WDOG, tuning I2C drive-strength, RMI4 and UCS1002 ALERT.
- Other small and random updates on various boards.
* tag 'imx-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
ARM: dts: imx6: RDU2: adjust audio devices nomenclature
ARM: dts: imx6: RDU2: only trigger IRQ on falling edge ucs1002 ALERT pin
ARM: dts: imx6: RDU2: enable RMI4 reduced reporting
ARM: dts: imx6: RDU2: reduce i2c drive-strength
ARM: dts: imx6: rdu2: enable WDOG1
ARM: dts: imx6-sr-som: increase at8035 PHY gigabit Tw parameter
ARM: dts: imx6: add wakeup support via magic packet
firmware: imx: select SOC_BUS to fix firmware build
arm64: dts: imx8mp: Correct the gpio ranges of gpio3
ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
ARM: dts: imx: e60k02: add second uart
ARM: dts: imx6sl-tolino-shine3: correct console uart pinmux
ARM: dts: imx6sl-tolino-shine2hd: add second uart
ARM: dts: imx6sl-tolino-shine2hd: correct console uart pinmux
ARM: imx: build suspend-imx6.S with arm instruction set
ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
ARM: dts: add Kverneland TGO board
ARM: dts: add Kverneland UT1, UT1Q and UT1P
ARM: dts: imx6ul-14x14-evk: Add camera support
ARM: dts: imx6ul-14x14-evk: Describe the KSZ8081 reset
...
Arnd Bergmann [Tue, 9 Feb 2021 16:59:58 +0000 (17:59 +0100)]
Merge tag 'imx-bindings-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.12:
- Various board compatible additions to fsl.yaml.
- Add vendor prefix for Plymovent and Kverneland Group.
- Update simple panel bindings to include compatible for EDT and Kyocera
panels.
* tag 'imx-bindings-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: imx: add imx8mm nitrogen support
dt-bindings: arm: fsl: Add the librem 5 Evergreen revision
dt-bindings: arm: fsl: add Kverneland TGO board
dt-bindings: arm: fsl: add Kverneland UT1, UT1Q and UI1P boards
dt-bindings: vendor-prefixes: Add an entry for Kverneland Group
dt-bindings: arm: fsl: add Kontron sl28 variant 1
bindings: arm: fsl: Add PHYTEC i.MX8MP devicetree bindings
dt-bindings: arm: fsl: add Protonic PRTI6G board
dt-bindings: arm: fsl: add Protonic MVT board
dt-bindings: arm: fsl: Add binding for Gateworks boards with IMX8MM
dt-bindings: soc: imx8m: add DT Binding doc for soc unique ID
dt-bindings: arm: fsl: add Plymovent BAS board
dt-bindings: arm: fsl: add Plymovent M2M board
dt-bindings: vendor-prefixes: Add an entry for Plymovent
dt-bindings: display: simple: Add Kyocera tcg070wvlq panel
dt-bindings: display: simple: add EDT compatibles already supported by the driver
dt-bindings: display: simple: fix alphabetical order for EDT compatibles
dt-bindings: arm: fsl: Add beacon,imx8mn-beacon-kit
Arnd Bergmann [Tue, 9 Feb 2021 16:53:44 +0000 (17:53 +0100)]
Merge tag 'qcom-arm64-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for 5.12
This introduces initial support for the new SM8350 platform, aka
Snapdragon 888, and the MTP device for this.
It adds PCIe, audio, display, GPU, HDMI watchdog, LLCC and PMIC ADC
support to the SM8250 platform and RB5 in particular, as well as improve
the definition of CPUs, thermal zones and fixes a few smaller issues.
It introduces new Devicetree files for the Alcatel Idol 3, ASUS Zenfone
2 Laser and BQ Aquaris X5, based on the MSM8916 platform.
It contains an overhaul of the existing MSM8992 and MSM8994 platform
files and introduces RPM power domains and SMP2P nodes. It adds
touchscreen, additional regulators, microSD card support and adds the
Sony Mobile Ivy, Karin, Suzuran and Satsuki devices. It joins the common
parts of the Lumia 950 and 950XL and extend these with support for
sensors, NFC, bluetooth, audio, microSD and Type-C mux pins.
It introduces support for the OnePlus6 and 6t, adds the missing higher
frequences for the SDM850 laptops, adds CPU cluster idle support on
SM8150 and a few tweaks to the SC7180 platform.
* tag 'qcom-arm64-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (100 commits)
arm64: dts: qcom: msm8998: Use rpmpd definitions for opp table levels
arm64: dts: qcom: msm8996: Add missing device_type under pcie[01]
arm64: dts: qcom: sc7180: Add support for gpu fuse
arm64: dts: qcom: msm8998: Disable some components by default
arm64: dts: qcom: msm8998: Add capacity-dmips-mhz to CPU cores
arm64: dts: qcom: msm8998: Add I2C pinctrl and fix BLSP2_I2C naming
arm64: dts: qcom: msm8998: Add DMA to I2C hosts
arm64: dts: qcom: msm8998: Merge in msm8998-pins.dtsi to msm8998.dtsi
arm64: dts: msm8916: Fix reserved and rfsa nodes unit address
arm64: dts: qcom: msm8994-octagon: Add AD7147 and APDS9930 sensors
arm64: dts: qcom: msm8994-octagon: Add TAS2553 codec
arm64: dts: qcom: msm8994-octagon: Add sensors on blsp1_i2c5
arm64: dts: qcom: msm8994-octagon: Add NXP NFC node
arm64: dts: qcom: msm8994-octagon: Add FM Radio and DDR regulator nodes
arm64: dts: qcom: msm8994-octagon: Configure PON keys
arm64: dts: qcom: msm8994-octagon: Configure Lattice iCE40 FPGA
arm64: dts: qcom: msm8994-octagon: Add uSD card and disable HS400 on eMMC
arm64: dts: qcom: msm8994-octagon: Configure HD3SS460 Type-C mux pins
arm64: dts: qcom: msm8994-octagon: Add QCA6174 bluetooth
arm64: dts: qcom: msm8994-octagon: Configure regulators
...
Arnd Bergmann [Tue, 9 Feb 2021 16:48:04 +0000 (17:48 +0100)]
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: amlogic updates for v5.12
- add thermal zones with cooling configuration
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: add the thermal-zones with cooling configuration
ARM: dts: meson8: add the thermal-zones with cooling configuration
ARM: dts: meson: add the ADC thermal sensor to meson.dtsi
ARM: dts: meson: move iio-hwmon for the SoC temperature to meson.dtsi
Arnd Bergmann [Tue, 9 Feb 2021 16:46:47 +0000 (17:46 +0100)]
Merge tag 'zynqmp-dt-for-v5.12' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: ZynqMP DT changes for v5.12
- Wire clock chips present on boards
- Enable reset, qspi, nand, watchdog and DP IPs
- Enable phy driver for sata and DP
- Add iommu description
- Add support for zcu104 revC+ boards
- Various small changes
- Add missing labels
- Fix typos in documentation
- Add missing boards
* tag 'zynqmp-dt-for-v5.12' of https://github.com/Xilinx/linux-xlnx:
arm64: dts: zynqmp: Wire up the DisplayPort subsystem
arm64: dts: zynqmp: Add DisplayPort subsystem
arm64: dts: zynqmp: Add DPDMA node
dt-bindings: arm: Fix typo in zcu111 board
arm64: dts: zynqmp: Add description for zcu104 revC
arm64: dts: zynqmp: Add missing iommu IDs
arm64: dts: zynqmp: Add missing lpd watchdog node
arm64: dts: zynqmp: Wire zynqmp qspi controller
arm64: dts: zynqmp: Wire arasan nand controller
arm64: dts: zynqmp: Add missing mio-bank properties to sdhcis
arm64: dts: zynqmp: Add label for zynqmp_ipi
arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
arm64: dts: zynqmp: Enable reset controller driver
arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
arm64: dts: zynqmp: Add address-cells property to interrupt controllers
Arnd Bergmann [Tue, 9 Feb 2021 16:46:11 +0000 (17:46 +0100)]
Merge tag 'samsung-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.12
1. Use new compatile to properly configure Exynos5420 USB2 PHY, fixing
it suspend/resume cycle.
2. Correct Samsung PMIC interrupt trigger levels on multiple boards.
3. Correct the voltages of Samsung GT-I9100 charger and add top-off
charger.
* tag 'samsung-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add top-off charging regulator node for I9100
ARM: dts: exynos: Fix charging regulator voltage and current for I9100
ARM: dts: exynos: correct PMIC interrupt trigger level on Odroid XU3 family
ARM: dts: exynos: correct PMIC interrupt trigger level on Arndale Octa
ARM: dts: exynos: correct PMIC interrupt trigger level on Spring
ARM: dts: exynos: correct PMIC interrupt trigger level on Rinato
ARM: dts: exynos: correct PMIC interrupt trigger level on Monk
ARM: dts: exynos: correct PMIC interrupt trigger level on Artik 5
ARM: dts: exynos: use Exynos5420 dedicated USB2 PHY compatible
arm64: dts: meson: add initial device-tree for ODROID-HC4
ODROID-HC4 is a derivative of the C4 with minor differences:
- 16MB XT25F128B SPI-NOR flash
- 2x SATA ports via ASM1061 PCIe to SATA controller
- 7-pin header with SPI and I2C for 1-inch OLED display and RTC
- 1x USB 2.0 host port
The 32-bit Amlogic Meson SoCs embed an ARC processor in the Always-On
power domain which is typically used for managing system suspend. The
memory for this ARC core is taken from the AHB SRAM area. Depending on
the actual SoC a different ARC core is used:
- Meson6 and earlier: some ARCv1 ISA based core (probably an ARC625)
- Meson8 and later: an ARC EM4 (ARCv2 ISA) based core
Add the device-tree node for this remote-processor along with the
required SRAM sections, clocks and reset-lines. Also use the
SoC-specific compatible string to manage any differences (should
they exist).
On Meson8, Meson8b and Meson8m2 the "secbus2" IO region is needed as
some bits need to be programmed there. Add this IO region for those
SoCs as well.
dt-bindings: Amlogic: add the documentation for the SECBUS2 registers
The Meson8/Meson8b/Meson8m2 SoCs have a register bank called SECBUS2 which
contains registers for various IP blocks such as pin-controller bits for
the BSD_EN and TEST_N GPIOs as well as some AO ARC core control bits.
The registers can be accessed directly when not running in "secure mode".
When "secure mode" is enabled then these registers have to be accessed
through secure monitor calls.
So far these SoCs are always known to boot in "non-secure mode".
Add a binding documentation using syscon (as these registers are shared
across different IPs) for the SECBUS2 registers.
dt-bindings: sram: Add compatible strings for the Meson AO ARC SRAM
Amlogic Meson8, Meson8b and Meson8m2 SoCs embed an ARC EM4 core
typically used for managing system suspend. A section of the SoCs SRAM
is mapped as memory for this ARC core. Add new compatible strings for
the SRAM section for the ARC core memory.
arm64: dts: meson: shorten audio card names for alsa compatibility
This patch shortens all audio card model names by dropping the SoC prefix
(for conformity) and rewording those that are still longer than alsa's 15
character name limit [0] to avoid userspace config issues.
Alexander Dahl [Mon, 28 Dec 2020 16:32:17 +0000 (17:32 +0100)]
arm64: dts: meson: Fix schema warnings for pwm-leds
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
arm64: dts: qcom: msm8998: Use rpmpd definitions for opp table levels
The dt-bindings/power/qcom-rpmpd.h header is being included in this
DT but the RPMPD OPP table declarations were using open-coded values:
use the definitions found in the aforementioned header.
Konrad Dybcio [Sat, 9 Jan 2021 16:29:59 +0000 (17:29 +0100)]
arm64: dts: qcom: msm8998: Disable some components by default
Some components (like PCIe) are not used on all devices and
with a certain firmware configuration they might end up triggering
a force reboot or a Synchronous Abort.
This commit brings no functional difference as the nodes are
enabled on devices which didn't disable them previously.
The BLSP2-connected interfaces started from 0 which is.. misleading
to say the least.. the clock names corresponding to these started
from 1, so let's align to that so as to reduce confusion.
Iskren Chernev [Mon, 1 Feb 2021 10:56:57 +0000 (12:56 +0200)]
ARM: dts: qcom: msm8974-klte: Mark essential regulators
s1 and l12 regulators are used for the memory and cache on the Samsung
S5 (klte). If they are turned off the phone shuts down. So mark them as
always-on to prevent that from happening.
* Move 35500 clock-frequency to kitakami (turns out it's a Sony specific)
* Add missing interfaces
* Fix the naming scheme
* Fix up pin assignments to make all BLSPs work
* Add DMA where previously omitted
RB5 has 3 PCIe ports exposed to connect PCIe client devices. PCIe0 is
connected to QCA6391 chipset and others are available on the HS3
expansion connector. Hence, enable all of them.
Add PCIe support for Qcom SM8250 SoC. This SoC has 3 PCIe Gen 3
instances based on Designware IP, out of which PCIe0 has 1 lane support
and the rest have 2 lane support.
Vinod Koul [Wed, 27 Jan 2021 12:30:54 +0000 (18:00 +0530)]
arm64: dts: qcom: Add basic devicetree support for SM8350-MTP board
Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC
MTP board. This enabled uart node and adds rpmh-regulators present for
this board.
Vincent Knecht [Sat, 30 Jan 2021 10:57:11 +0000 (11:57 +0100)]
arm64: dts: qcom: Add device tree for Alcatel Idol 3 (4.7")
The Alcatel Idol 3 (4.7") is a smartphone based on MSM8916.
Add a device tree with support for USB, eMMC, SD-Card, WiFi,
BT, power/volume buttons, vibrator and the following sensors:
magnetometer, accelerometer, gyroscope, ambient light+proximity
Lubomir Rintel [Thu, 21 Jan 2021 03:41:29 +0000 (04:41 +0100)]
ARM: dts: mmp3-dell-ariel: Replace SSP2 with spi-gpio
The firmware leaves the pins in GPIO mode. Until we have a proper pinmux
driver hooked on we just need to bitbang SPI. No big deal, this is just
used for the power button and performance is not important.
Lubomir Rintel [Thu, 21 Jan 2021 03:41:28 +0000 (04:41 +0100)]
ARM: dts: mmp3-dell-ariel: Add the power button node
This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.
However, while the EC itself is controlled via I2C, the input capability
for the power button acts as a separate device attached to the SPI, hence
it has a separate device node.
Lubomir Rintel [Thu, 21 Jan 2021 03:41:23 +0000 (04:41 +0100)]
ARM: dts: mmp3-dell-ariel: Drop linux,usable-memory from /memory
Drop the linux,usable-memory properties; the schema is unhappy about
them.
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
Arnd Bergmann [Tue, 2 Feb 2021 17:03:54 +0000 (18:03 +0100)]
Merge tag 'mvebu-dt64-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.12 (part 1)
- rename u-boot mtd partition to a53-firmware on Turris Mox (Armada 3720 based)
- improve SDHCI support on AP807 based board
- move SATA comphy into main armada-37xx.dtsi
- add Armada 8K/7K PWM support
* tag 'mvebu-dt64-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: armada: add pwm offsets for ap/cp gpios
arm64: dts: marvell: armada-37xx: Add SATA comphy into main armada-37xx.dtsi file
arm64: dts: cn913x-db: enable MMC HS400
arm64: dts: change AP807 SDHCI compatibility string
arm64: dts: armada-3720-turris-mox: rename u-boot mtd partition to a53-firmware
Arnd Bergmann [Tue, 2 Feb 2021 17:02:48 +0000 (18:02 +0100)]
Merge tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.12 (part 1)
Improve LED and fan support on Helios4 boad (Armada 388 based)
Add ECC configuration for Linksys board (Aramda 385 based)
* tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada388-helios4: assign pinctrl to each fan
ARM: dts: armada388-helios4: assign pinctrl to LEDs
ARM: dts: armada-385-linksys: fix usage with newer devices
Arnd Bergmann [Tue, 2 Feb 2021 17:00:48 +0000 (18:00 +0100)]
Merge tag 'v5.11-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt6779:
- add DEVAPC node to detect mallicious bus accesses
- add PMIC wrapper node
mt7622:
- add reset to mmc node
mt8183:
- fix typo in drma-fifo-size property
- refine compatible for the disp-gamma
- add phandel of PM domain to the PWM node
- add second PWM node
- add regulator to MFG power domain
- enable DSI node in kukui
- add krane sku0, which uses different panel
- fix mailbox dt-bindings include path
mt8192:
- add NOR flash node
- add PSCI based CPU idle states
mt8516:
- add node for the UART's APDMA controller
* tag 'v5.11-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: Fix GCE include path
dts64: mt7622: fix slow sd card access
dt-bindings: arm64: dts: mediatek: Add krane sku0
arm64: dts: mt8183: Add krane-sku0 board.
arm64: dts: mt8183: config dsi node
arm64: dts: mt6779: Support pwrap on Mediatek MT6779 platform
arm64: dts: mt6779: Support devapc
arm64: dts: mt8192: Add cpu-idle-states
arm64: dts: mediatek: mt8183: Add domain supply for mfg
arm64: dts: mt8192: add nor_flash device node
arm64: dts: mediatek: mt8516: add support for APDMA
arm64: dts: mediatek: mt8183-evb: add PWM support
arm64: dts: mediatek: mt8183: add pwm node
arm64: dts: mt8183: Add missing power-domain for pwm0 node
arm64: dts: mt8183: refine gamma compatible name
arm64: dts: mt8183: rename rdma fifo size
Arnd Bergmann [Tue, 2 Feb 2021 16:58:32 +0000 (17:58 +0100)]
Merge tag 'arm-soc/for-5.12/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.12 please pull the following:
- Rafal continues to add support for the 4906/4908 SoC family and adds
a Device Tree for the Netgear R8000P router (4906-based), describes
the NAND controller of the 4908 more appropriately (based on the older
63138 DSL SoC), describes the 4908 PCIe reset controller, internal
Ethernet switch (Starfighter 2 switch) and finally the Power
Management Bus (PMB)
- Scott removes all of the SATA-related Device Tree nodes since SATA
is unused on the Stingray product line
Arnd Bergmann [Tue, 2 Feb 2021 16:57:14 +0000 (17:57 +0100)]
Merge tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.12, please pull the following:
- Dave adds a proper compatile string for the DSI1 panel on 2711
(Raspberry Pi 4) to permit adequate driver differentiation
- Nicolas declares reserved memory regions filed by the Rasbperry Pi
bootloader to indicate the running system configuration
- Maxime declares the BSC (HDMI I2C controller) and CEC interrupt
controllers
- Stanislav fixes a tab vs. space issue in the BCM21664 DTS
* tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Add the CEC interrupt controller
ARM: dts: bcm21664: Replace spaces with a tab
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration
ARM: dts: bcm2711: Use compatible string for BCM2711 DSI1
Arnd Bergmann [Tue, 2 Feb 2021 16:53:02 +0000 (17:53 +0100)]
Merge tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
- DT fixes spotted through the schemas
- Mali Support for the A10s/A13/GR8/R8
- MMC improvements for the A64 and H6
- New board: SL631 Action Camera, PineTab Early Adopter
* tag 'sunxi-dt-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (47 commits)
ARM: dts: sunxi: Rename nmi_intc to r_intc
ARM: dts: sun8i: h2-plus: bananapi-m2-zero: Increase BT UART speed
ARM: dts: sunxi: bananapi-m2-plus: Increase BT UART speed
arm64: dts: allwinner: pine-h64: Fix typos in BT GPIOs
arm64: dts: allwinner: pinetab: Fix the panel compatible
arm64: dts: allwinner: pinephone: Remove useless light sensor supplies
arm64: dts: allwinner: h6: Use - instead of @ for DT OPP entries
ARM: dts: sun8i-a33: sina33: Add missing panel power supply
ARM: dts: sun8i-a83t: Remove empty CSI port
ARM: dts: sun8i-s3: pinecube: Fix CSI DTC warnings
ARM: dts: sun8i-s3: impetus: Fix the USB PHY ID detect GPIO properties
ARM: dts: sun8i: nanopi-r1: Fix GPIO regulator state array
ARM: dts: sun6i: primo81: Remove useless io-channel-cells
ARM: dts: sunxi: Fix CPU thermal zone node name
ARM: dts: sunxi: Add missing backlight supply
ARM: dts: sunxi: Fix the LED node names
dt-bindings: rtc: sun6i-a31-rtc: Loosen the requirements on the clocks
dt-bindings: iio: adc: Add AXP803 compatible
dt-bindings: sunxi: Fix the pinecube compatible
ARM: dts: sun8i-v3s: Add CSI0 MCLK pin definition
...
Michal Simek [Thu, 21 Jan 2021 10:27:00 +0000 (11:27 +0100)]
arm64: dts: zynqmp: Add description for zcu104 revC
Xilinx ZynqMP zcu104 revC and newer board revisions have different i2c
structure compare to revA. The rest of the board is the same from software
perspective.
Also enable DMAs and QSPI.
Michal Simek [Thu, 21 Jan 2021 10:26:58 +0000 (11:26 +0100)]
arm64: dts: zynqmp: Add missing lpd watchdog node
Xilinx ZynqMP SoC has FPD (Full Power Domain) and LPD (Low Power Domain)
watchdogs. There are cases where also LPD WDT should be used by Arm cores
that's why list it with disabled status.
Michal Simek [Thu, 21 Jan 2021 10:26:55 +0000 (11:26 +0100)]
arm64: dts: zynqmp: Add missing mio-bank properties to sdhcis
Add missing xlnx,mio-bank property to sdhci nodes. Also add properties with
0 value to have it listed in case that files are copied to different
projects where default case doesn't need to be handled in the same way.
That's why explicitly list them too.
projects / linux.git / log