Vladimir Oltean [Sun, 4 Aug 2019 22:38:46 +0000 (01:38 +0300)]
net: dsa: sja1105: Really fix panic on unregistering PTP clock
The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d355f ("net: dsa: sja1105: Cancel PTP delayed work on unregister") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:45 +0000 (01:38 +0300)]
net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224ea ("net: dsa: sja1105: Implement is_static for FDB entries on E/T") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vladimir Oltean [Sun, 4 Aug 2019 22:38:44 +0000 (01:38 +0300)]
net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through standalone ports") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: Georg Waibel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Nishka Dasgupta [Sun, 4 Aug 2019 15:30:18 +0000 (21:00 +0530)]
net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there
is no put, thus causing a memory leak. Hence add an of_node_put() before
the return.
Additionally, the local variable ports in the function
qca8k_setup_mdio_bus() takes the return value of of_get_child_by_name(),
which gets a node but does not put it. If the function returns without
putting ports, it may cause a memory leak. Hence put ports before the
mid-loop return statement, and also outside the loop after its last usage
in this function.
Issues found with Coccinelle.
David S. Miller [Tue, 6 Aug 2019 21:15:39 +0000 (14:15 -0700)]
Merge branch 'flow_offload-action-fixes'
Vlad Buslov says:
====================
action fixes for flow_offload infra compatibility
Fix rcu warnings due to usage of action helpers that expect rcu read lock
protection from rtnl-protected context of flow_offload infra.
====================
Change tcf_sample_psample_group() helper to allow using it from both rtnl
and rcu protected contexts.
Fixes: a7a7be6087b0 ("net/sched: add sample action to the hardware intermediate representation") Signed-off-by: Vlad Buslov <[email protected]> Reviewed-by: Pieter Jansen van Vuuren <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Change tcf_police_rate_bytes_ps() and tcf_police_tcfp_burst() helpers to
allow using them from both rtnl and rcu protected contexts.
Fixes: 8c8cfc6ed274 ("net/sched: add police action to the hardware intermediate representation") Signed-off-by: Vlad Buslov <[email protected]> Reviewed-by: Pieter Jansen van Vuuren <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Tue, 6 Aug 2019 21:14:01 +0000 (14:14 -0700)]
Merge branch 'hisilicon-fixes'
Jiangfeng Xiao says:
====================
net: hisilicon: Fix a few problems with hip04_eth
During the use of the hip04_eth driver,
several problems were found,
which solved the hip04_tx_reclaim reentry problem,
fixed the problem that hip04_mac_start_xmit never
returns NETDEV_TX_BUSY
and the dma_map_single failed on the arm64 platform.
====================
Jiangfeng Xiao [Sat, 3 Aug 2019 12:31:41 +0000 (20:31 +0800)]
net: hisilicon: Fix dma_map_single failed on arm64
On the arm64 platform, executing "ifconfig eth0 up" will fail,
returning "ifconfig: SIOCSIFFLAGS: Input/output error."
ndev->dev is not initialized, dma_map_single->get_dma_ops->
dummy_dma_ops->__dummy_map_page will return DMA_ERROR_CODE
directly, so when we use dma_map_single, the first parameter
is to use the device of platform_device.
Jiangfeng Xiao [Sat, 3 Aug 2019 12:31:40 +0000 (20:31 +0800)]
net: hisilicon: fix hip04-xmit never return TX_BUSY
TX_DESC_NUM is 256, in tx_count, the maximum value of
mod(TX_DESC_NUM - 1) is 254, the variable "count" in
the hip04_mac_start_xmit function is never equal to
(TX_DESC_NUM - 1), so hip04_mac_start_xmit never
return NETDEV_TX_BUSY.
tx_count is modified to mod(TX_DESC_NUM) so that
the maximum value of tx_count can reach
(TX_DESC_NUM - 1), then hip04_mac_start_xmit can reurn
NETDEV_TX_BUSY.
Jiangfeng Xiao [Sat, 3 Aug 2019 12:31:39 +0000 (20:31 +0800)]
net: hisilicon: make hip04_tx_reclaim non-reentrant
If hip04_tx_reclaim is interrupted while it is running
and then __napi_schedule continues to execute
hip04_rx_poll->hip04_tx_reclaim, reentrancy occurs
and oops is generated. So you need to mask the interrupt
during the hip04_tx_reclaim run.
====================
Fix batched event generation for vlan action
When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.
For example, consider the following script adding 32 entries with all
supported vlan parameters (in order to maximize netlink messages size):
$TC actions flush action vlan
for i in `seq 1 $1`;
do
cmd="action vlan push protocol 802.1q id 4094 priority 7 pipe \
index $i cookie aabbccddeeff112233445566778800a1 "
args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%
patch 1 adds callback in tc_action_ops of vlan action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().
patch 2 updates the TDC test suite with relevant vlan test cases.
====================
Jose Abreu [Tue, 6 Aug 2019 13:16:16 +0000 (15:16 +0200)]
net: stmmac: xgmac: Fix XGMAC selftests
Fixup the XGMAC selftests by correctly finishing the implementation of
set_filter callback.
Result:
$ ethtool -t enp4s0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters -95
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
David S. Miller [Tue, 6 Aug 2019 18:48:48 +0000 (11:48 -0700)]
Merge tag 'wireless-drivers-for-davem-2019-08-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.3
Second set of fixes for 5.3. Lots of iwlwifi fixes have accumulated
which consists most of patches in this pull request. Only most notable
iwlwifi fixes are listed below.
mwifiex
* fix a regression related to WPA1 networks since v5.3-rc1
iwlwifi
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
====================
Denis Kirjanov [Tue, 6 Aug 2019 10:51:11 +0000 (12:51 +0200)]
be2net: disable bh with spin_lock in be_process_mcc
be_process_mcc() is invoked in 3 different places and
always with BHs disabled except the be_poll function
but since it's invoked from softirq with BHs
disabled it won't hurt.
v1->v2: added explanation to the patch
v2->v3: add a missing call from be_cmds.c
Chen-Yu Tsai [Tue, 6 Aug 2019 07:35:39 +0000 (15:35 +0800)]
net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
The sun4i-emac uses the "phy" property to find the PHY it's supposed to
use. This property was deprecated in favor of "phy-handle" in commit 8c5b09447625 ("dt-bindings: net: sun4i-emac: Convert the binding to a
schemas").
Add support for this new property name, and fall back to the old one in
case the device tree hasn't been updated.
net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
drivers/net/ethernet/marvell/mvmdio.c: Fix non OF case
Orion5.x systems are still using machine files and not device-tree.
Commit 96cb4342382290c9 ("net: mvmdio: allow up to three clocks to be
specified for orion-mdio") has replaced devm_clk_get() with of_clk_get(),
leading to a oops at boot and not working network, as reported in
https://lists.debian.org/debian-arm/2019/07/msg00088.html and possibly in
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908712.
Ursula Braun [Fri, 2 Aug 2019 08:47:50 +0000 (10:47 +0200)]
net/smc: avoid fallback in case of non-blocking connect
FASTOPEN is not possible with SMC. sendmsg() with msg_flag MSG_FASTOPEN
triggers a fallback to TCP if the socket is in state SMC_INIT.
But if a nonblocking connect is already started, fallback to TCP
is no longer possible, even though the socket may still be in state
SMC_INIT.
And if a nonblocking connect is already started, a listen() call
does not make sense.
Ursula Braun [Fri, 2 Aug 2019 08:16:38 +0000 (10:16 +0200)]
net/smc: do not schedule tx_work in SMC_CLOSED state
The setsockopts options TCP_NODELAY and TCP_CORK may schedule the
tx worker. Make sure the socket is not yet moved into SMC_CLOSED
state (for instance by a shutdown SHUT_RDWR call).
gve: Fix case where desc_cnt and data_cnt can get out of sync
desc_cnt and data_cnt should always be equal. In the case of a dropped
packet desc_cnt was still getting updated (correctly), data_cnt
was not. To eliminate this bug and prevent it from recurring this
patch combines them into one ring level cnt.
David Ahern [Thu, 1 Aug 2019 21:36:35 +0000 (14:36 -0700)]
ipv6: Fix unbalanced rcu locking in rt6_update_exception_stamp_rt
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d806 ("ipv6: Handle all fib6_nh in a nexthop in exception handling") Signed-off-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Thu, 1 Aug 2019 21:36:01 +0000 (14:36 -0700)]
net/tls: partially revert fix transition through disconnect with close
Looks like we were slightly overzealous with the shutdown()
cleanup. Even though the sock->sk_state can reach CLOSED again,
socket->state will not got back to SS_UNCONNECTED once
connections is ESTABLISHED. Meaning we will see EISCONN if
we try to reconnect, and EINVAL if we try to listen.
Only listen sockets can be shutdown() and reused, but since
ESTABLISHED sockets can never be re-connected() or used for
listen() we don't need to try to clean up the ULP state early.
Fixes: 32857cf57f92 ("net/tls: fix transition through disconnect with close") Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
====================
net: fix regressions for generic-XDP
Thanks to Brandon Cazander, who wrote a very detailed bug report that
even used perf probe's on xdp-newbies mailing list, we discovered that
generic-XDP contains some regressions when using bpf_xdp_adjust_head().
First issue were that my selftests script, that use bpf_xdp_adjust_head(),
by mistake didn't use generic-XDP any-longer. That selftest should have
caught the real regression introduced in commit 458bf2f224f0 ("net: core:
support XDP generic on stacked devices.").
To verify this patchset fix the regressions, you can invoked manually via:
cd tools/testing/selftests/bpf/
sudo ./test_xdp_vlan_mode_generic.sh
sudo ./test_xdp_vlan_mode_native.sh
====================
net: fix bpf_xdp_adjust_head regression for generic-XDP
When generic-XDP was moved to a later processing step by commit 458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
a regression was introduced when using bpf_xdp_adjust_head.
The issue is that after this commit the skb->network_header is now
changed prior to calling generic XDP and not after. Thus, if the header
is changed by XDP (via bpf_xdp_adjust_head), then skb->network_header
also need to be updated again. Fix by calling skb_reset_network_header().
Fixes: 458bf2f224f0 ("net: core: support XDP generic on stacked devices.") Reported-by: Brandon Cazander <[email protected]> Signed-off-by: Jesper Dangaard Brouer <[email protected]> Signed-off-by: David S. Miller <[email protected]>
selftests/bpf: reduce time to execute test_xdp_vlan.sh
Given the increasing number of BPF selftests, it makes sense to
reduce the time to execute these tests. The ping parameters are
adjusted to reduce the time from measures 9 sec to approx 2.8 sec.
selftests/bpf: add wrapper scripts for test_xdp_vlan.sh
In-order to test both native-XDP (xdpdrv) and generic-XDP (xdpgeneric)
create two wrapper test scripts, that start the test_xdp_vlan.sh script
with these modes.
Change BPF selftest test_xdp_vlan.sh to (default) use generic XDP.
This selftest was created together with a fix for generic XDP, in commit 297249569932 ("net: fix generic XDP to handle if eth header was
mangled"). And was suppose to catch if generic XDP was broken again.
The tests are using veth and assumed that veth driver didn't support
native driver XDP, thus it used the (ip link set) 'xdp' attach that fell
back to generic-XDP. But veth gained native-XDP support in 948d4f214fde
("veth: Add driver XDP"), which caused this test script to use
native-XDP.
Fixes: 948d4f214fde ("veth: Add driver XDP") Fixes: 97396ff0bc2d ("selftests/bpf: add XDP selftests for modifying and popping VLAN headers") Signed-off-by: Jesper Dangaard Brouer <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Qian Cai [Thu, 1 Aug 2019 13:52:54 +0000 (09:52 -0400)]
net/mlx5e: always initialize frag->last_in_page
The commit 069d11465a80 ("net/mlx5e: RX, Enhance legacy Receive Queue
memory scheme") introduced an undefined behaviour below due to
"frag->last_in_page" is only initialized in mlx5e_init_frags_partition()
when,
if (next_frag.offset + frag_info[f].frag_stride > PAGE_SIZE)
or after bailed out the loop,
for (i = 0; i < mlx5_wq_cyc_get_size(&rq->wqe.wq); i++)
As the result, there could be some "frag" have uninitialized
value of "last_in_page".
Later, get_frag() obtains those "frag" and check "frag->last_in_page" in
mlx5e_put_rx_frag() and triggers the error during boot. Fix it by always
initializing "frag->last_in_page" to "false" in
mlx5e_init_frags_partition().
UBSAN: Undefined behaviour in
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:325:12
load of value 170 is not a valid value for type 'bool' (aka '_Bool')
Call trace:
dump_backtrace+0x0/0x264
show_stack+0x20/0x2c
dump_stack+0xb0/0x104
__ubsan_handle_load_invalid_value+0x104/0x128
mlx5e_handle_rx_cqe+0x8e8/0x12cc [mlx5_core]
mlx5e_poll_rx_cq+0xca8/0x1a94 [mlx5_core]
mlx5e_napi_poll+0x17c/0xa30 [mlx5_core]
net_rx_action+0x248/0x940
__do_softirq+0x350/0x7b8
irq_exit+0x200/0x26c
__handle_domain_irq+0xc8/0x128
gic_handle_irq+0x138/0x228
el1_irq+0xb8/0x140
arch_cpu_idle+0x1a4/0x348
do_idle+0x114/0x1b0
cpu_startup_entry+0x24/0x28
rest_init+0x1ac/0x1dc
arch_call_rest_init+0x10/0x18
start_kernel+0x4d4/0x57c
Fixes: 069d11465a80 ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme") Signed-off-by: Qian Cai <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dmytro Linkin [Thu, 1 Aug 2019 13:02:51 +0000 (13:02 +0000)]
net: sched: use temporary variable for actions indexes
Currently init call of all actions (except ipt) init their 'parm'
structure as a direct pointer to nla data in skb. This leads to race
condition when some of the filter actions were initialized successfully
(and were assigned with idr action index that was written directly
into nla data), but then were deleted and retried (due to following
action module missing or classifier-initiated retry), in which case
action init code tries to insert action to idr with index that was
assigned on previous iteration. During retry the index can be reused
by another action that was inserted concurrently, which causes
unintended action sharing between filters.
To fix described race condition, save action idr index to temporary
stack-allocated variable instead on nla data.
Johan Hovold [Mon, 5 Aug 2019 10:00:55 +0000 (12:00 +0200)]
NFC: nfcmrvl: fix gpio-handling regression
Fix two reset-gpio sanity checks which were never converted to use
gpio_is_valid(), and make sure to use -EINVAL to indicate a missing
reset line also for the UART-driver module parameter and for the USB
driver.
This specifically prevents the UART and USB drivers from incidentally
trying to request and use gpio 0, and also avoids triggering a WARN() in
gpio_to_desc() during probe when no valid reset line has been specified.
There are a lot of those warnings with GCC8+ 64-bit,
In file included from ./include/linux/sctp.h:42,
from net/core/skbuff.c:47:
./include/uapi/linux/sctp.h:395:1: warning: alignment 4 of 'struct
sctp_paddr_change' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:728:1: warning: alignment 4 of 'struct
sctp_setpeerprim' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:727:26: warning: 'sspp_addr' offset 4 in
'struct sctp_setpeerprim' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage sspp_addr;
^~~~~~~~~
./include/uapi/linux/sctp.h:741:1: warning: alignment 4 of 'struct
sctp_prim' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:740:26: warning: 'ssp_addr' offset 4 in
'struct sctp_prim' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage ssp_addr;
^~~~~~~~
./include/uapi/linux/sctp.h:792:1: warning: alignment 4 of 'struct
sctp_paddrparams' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:784:26: warning: 'spp_address' offset 4 in
'struct sctp_paddrparams' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage spp_address;
^~~~~~~~~~~
./include/uapi/linux/sctp.h:905:1: warning: alignment 4 of 'struct
sctp_paddrinfo' is less than 8 [-Wpacked-not-aligned]
} __attribute__((packed, aligned(4)));
^
./include/uapi/linux/sctp.h:899:26: warning: 'spinfo_address' offset 4
in 'struct sctp_paddrinfo' isn't aligned to 8 [-Wpacked-not-aligned]
struct sockaddr_storage spinfo_address;
^~~~~~~~~~~~~~
This is because the commit 20c9c825b12f ("[SCTP] Fix SCTP socket options
to work with 32-bit apps on 64-bit kernels.") added "packed, aligned(4)"
GCC attributes to some structures but one of the members, i.e, "struct
sockaddr_storage" in those structures has the attribute,
"aligned(__alignof__ (struct sockaddr *)" which is 8-byte on 64-bit
systems, so the commit overwrites the designed alignments for
"sockaddr_storage".
To fix this, "struct sockaddr_storage" needs to be aligned to 4-byte as
it is only used in those packed sctp structure which is part of UAPI,
and "struct __kernel_sockaddr_storage" is used in some other
places of UAPI that need not to change alignments in order to not
breaking userspace.
Use an implicit alignment for "struct __kernel_sockaddr_storage" so it
can keep the same alignments as a member in both packed and un-packed
structures without breaking UAPI.
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
YueHaibing [Thu, 1 Aug 2019 01:24:19 +0000 (09:24 +0800)]
enetc: Select PHYLIB while CONFIG_FSL_ENETC_VF is set
Like FSL_ENETC, when CONFIG_FSL_ENETC_VF is set,
we should select PHYLIB, otherwise building still fails:
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c:(.text+0x2744): undefined reference to `phy_start'
enetc.c:(.text+0x282c): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c:(.text+0x28f8): undefined reference to `phy_stop'
enetc.c:(.text+0x2904): undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x3f8): undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o:(.rodata+0x400): undefined reference to `phy_ethtool_set_link_ksettings'
Reported-by: Hulk Robot <[email protected]> Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: YueHaibing <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Wang Xiayang [Wed, 31 Jul 2019 08:15:42 +0000 (16:15 +0800)]
net/ethernet/qlogic/qed: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string
size equals to the destination buffer size 30.
The output string is passed to qed_int_deassertion_aeu_bit()
which calls DP_INFO() and relies NULL-termination.
Use strlcpy instead. The other conditional branch above strncpy()
needs no fix as snprintf() ensures NULL-termination.
board is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/iphase.c:2765 ia_ioctl() warn: potential spectre issue 'ia_dev' [r] (local cap)
drivers/atm/iphase.c:2774 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2782 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2816 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2823 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2830 ia_ioctl() warn: potential spectre issue '_ia_dev' [r] (local cap)
drivers/atm/iphase.c:2845 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2856 ia_ioctl() warn: possible spectre second half. 'iadev'
Fix this by sanitizing board before using it to index ia_dev and _ia_dev
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Dexuan Cui [Wed, 31 Jul 2019 01:25:45 +0000 (01:25 +0000)]
hv_sock: Fix hang when a connection is closed
There is a race condition for an established connection that is being closed
by the guest: the refcnt is 4 at the end of hvs_release() (Note: here the
'remove_sock' is false):
1 for the initial value;
1 for the sk being in the bound list;
1 for the sk being in the connected list;
1 for the delayed close_work.
After hvs_release() finishes, __vsock_release() -> sock_put(sk) *may*
decrease the refcnt to 3.
Concurrently, hvs_close_connection() runs in another thread:
calls vsock_remove_sock() to decrease the refcnt by 2;
call sock_put() to decrease the refcnt to 0, and free the sk;
next, the "release_sock(sk)" may hang due to use-after-free.
In the above, after hvs_release() finishes, if hvs_close_connection() runs
faster than "__vsock_release() -> sock_put(sk)", then there is not any issue,
because at the beginning of hvs_close_connection(), the refcnt is still 4.
The issue can be resolved if an extra reference is taken when the
connection is established.
Fixes: a9eeb998c28d ("hv_sock: Add support for delayed close") Signed-off-by: Dexuan Cui <[email protected]> Reviewed-by: Sunil Muthuswamy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Wang Xiayang [Wed, 31 Jul 2019 07:25:59 +0000 (15:25 +0800)]
can: peak_usb: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.
Wang Xiayang [Wed, 31 Jul 2019 07:31:14 +0000 (15:31 +0800)]
can: sja1000: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string
'name' is passed to dev_info which relies on NULL-termination.
tipc: compat: allow tipc commands without arguments
Commit 2753ca5d9009 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
net: broadcom: Fix manufacturer name in Kconfig help text
The help text refers to AMD instead of Broadcom, presumably because it
was copied from the former.
Fixes: adfc5217e9db68d3 ("broadcom: Move the Broadcom drivers") Signed-off-by: Geert Uytterhoeven <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: apple: Fix manufacturer name in Kconfig help text
The help text refers to IBM instead of Apple, presumably because it was
copied from the former.
Fixes: 8fb6b0908176704a ("bmac/mace/macmace/mac89x0/cs89x0: Move the Macintosh (Apple) drivers") Signed-off-by: Geert Uytterhoeven <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: 8390: Fix manufacturer name in Kconfig help text
The help text refers to Western Digital instead of National
Semiconductor 8390, presumably because it was copied from the former.
Fixes: 644570b830266ff3 ("8390: Move the 8390 related drivers") Signed-off-by: Geert Uytterhoeven <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Matteo Croce [Thu, 1 Aug 2019 12:13:30 +0000 (14:13 +0200)]
mvpp2: fix panic on module removal
mvpp2 uses a delayed workqueue to gather traffic statistics.
On module removal the workqueue can be destroyed before calling
cancel_delayed_work_sync() on its works.
Fix it by moving the destroy_workqueue() call after mvpp2_port_remove().
Also remove an unneeded call to flush_workqueue()
net: bridge: mcast: don't delete permanent entries when fast leave is enabled
When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.
Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
$
After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
Fixes: ccb1c31a7a87 ("bridge: add flags to distinguish permanent mdb entires") Signed-off-by: Nikolay Aleksandrov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Mon, 29 Jul 2019 23:08:03 +0000 (16:08 -0700)]
selftests/tls: fix TLS tests with CONFIG_TLS=n
Build bot reports some recent TLS tests are failing
with CONFIG_TLS=n. Correct the expected return code
and skip TLS installation if not supported.
Tested with CONFIG_TLS=n and CONFIG_TLS=m.
Reported-by: kernel test robot <[email protected]> Fixes: cf32526c8842 ("selftests/tls: add a test for ULP but no keys") Fixes: 65d41fb317c6 ("selftests/tls: add a bidirectional test") Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Wed, 31 Jul 2019 15:51:34 +0000 (08:51 -0700)]
Merge tag 'mac80211-for-davem-2019-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* revert NETIF_F_LLTX usage as it caused problems
* avoid warning on WMM parameters from AP that are too short
* fix possible null-ptr dereference in hwsim
* fix interface combinations with 4-addr and crypto control
====================
net: ethernet: et131x: Use GFP_KERNEL instead of GFP_ATOMIC when allocating tx_ring->tcb_ring
There is no good reason to use GFP_ATOMIC here. Other memory allocations
are performed with GFP_KERNEL (see other 'dma_alloc_coherent()' below and
'kzalloc()' in 'et131x_rx_dma_memory_alloc()')
drop_monitor: Add missing uAPI file to MAINTAINERS file
Fixes: 6e43650cee64 ("add maintainer for network drop monitor kernel service") Signed-off-by: Ido Schimmel <[email protected]> Acked-by: Neil Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Wed, 31 Jul 2019 15:22:12 +0000 (08:22 -0700)]
Merge branch 'mlxsw-Two-small-fixes'
Ido Schimmel says:
====================
mlxsw: Two small fixes
Patch #1 from Jiri fixes the error path of the module initialization
function. Found during manual code inspection.
Patch #2 from Petr further reduces the default shared buffer pool sizes
in order to work around a problem that was originally described in
commit e891ce1dd2a5 ("mlxsw: spectrum_buffers: Reduce pool size on
Spectrum-2").
====================
Petr Machata [Wed, 31 Jul 2019 06:33:15 +0000 (09:33 +0300)]
mlxsw: spectrum_buffers: Further reduce pool size on Spectrum-2
In commit e891ce1dd2a5 ("mlxsw: spectrum_buffers: Reduce pool size on
Spectrum-2"), pool size was reduced to mitigate a problem in port buffer
usage of ports split four ways. It turns out that this work around does not
solve the issue, and a further reduction is required.
Thus reduce the size of pool 0 by another 2.7 MiB, and round down to the
whole number of cells.
Fixes: e891ce1dd2a5 ("mlxsw: spectrum_buffers: Reduce pool size on Spectrum-2") Signed-off-by: Petr Machata <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
mlxsw: spectrum: Fix error path in mlxsw_sp_module_init()
In case of sp2 pci driver registration fail, fix the error path to
start with sp1 pci driver unregister.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC") Signed-off-by: Jiri Pirko <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Kalle Valo [Wed, 31 Jul 2019 11:51:55 +0000 (14:51 +0300)]
Merge tag 'iwlwifi-fixes-for-kvalo-2019-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
We have a lot of fixes, most of them are also applicable to stable.
Notably:
* fix use-after-free issues
* fix DMA mapping API usage errors
* fix frame drop occurring due to reorder buffer handling in
RSS in certain conditions
* fix rate scale locking issues
* disable TX A-MSDU on older NICs as it causes problems and was
never supposed to be supported
* new PCI IDs
* GEO_TX_POWER_LIMIT API issue that many people were hitting
Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.
Guillaume Nault adds:
And the implementation was broken until 2016 (see 29e73269aa4d ("pppoe:
fix reference counting in PPPoE proxy")), and nobody ever noticed. I
should probably have removed this ioctl entirely instead of fixing it.
Clearly, it has never been used.
Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.
All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.
The reason is that the skb list tipc_socket::mc_method.deferredq only
is initialized for connectionless sockets, while nothing stops arriving
multicast messages from being filtered by connection oriented sockets,
with subsequent access to the said list.
We fix this by initializing the list unconditionally at socket creation.
This eliminates the crash, while the message still is dropped further
down in tipc_sk_filter_rcv() as it should be.
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_open':
enetc.c: undefined reference to `phy_disconnect'
enetc.c: undefined reference to `phy_start'
drivers/net/ethernet/freescale/enetc/enetc.o: In function `enetc_close':
enetc.c: undefined reference to `phy_stop'
enetc.c: undefined reference to `phy_disconnect'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_get_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_ethtool.o: undefined reference to `phy_ethtool_set_link_ksettings'
drivers/net/ethernet/freescale/enetc/enetc_mdio.o: In function `enetc_mdio_probe':
enetc_mdio.c: undefined reference to `mdiobus_alloc_size'
enetc_mdio.c: undefined reference to `mdiobus_free'
Jose Abreu [Tue, 30 Jul 2019 13:57:16 +0000 (15:57 +0200)]
net: stmmac: Sync RX Buffer upon allocation
With recent changes that introduced support for Page Pool in stmmac, Jon
reported that NFS boot was no longer working on an ARM64 based platform
that had the IP behind an IOMMU.
As Page Pool API does not guarantee DMA syncing because of the use of
DMA_ATTR_SKIP_CPU_SYNC flag, we have to explicit sync the whole buffer upon
re-allocation because we are always re-using same pages.
In fact, ARM64 code invalidates the DMA area upon two situations [1]:
- sync_single_for_cpu(): Invalidates if direction != DMA_TO_DEVICE
- sync_single_for_device(): Invalidates if direction == DMA_FROM_DEVICE
So, as we must invalidate both the current RX buffer and the newly allocated
buffer we propose this fix.
Colin Ian King [Tue, 30 Jul 2019 11:47:52 +0000 (12:47 +0100)]
mlxsw: spectrum_ptp: fix duplicated check on orig_egr_types
Currently are duplicated checks on orig_egr_types which are
redundant, I believe this is a typo and should actually be
orig_ing_types || orig_egr_types instead of the expression
orig_egr_types || orig_egr_types. Fix these.
Addresses-Coverity: ("Same on both sides") Fixes: c6b36bdd04b5 ("mlxsw: spectrum_ptp: Increase parsing depth when PTP is enabled") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: phy: fixed_phy: print gpio error only if gpio node is present
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f7034 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()") Signed-off-by: Hubert Feurstein <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
iwlwifi: mvm: fix a use-after-free bug in iwl_mvm_tx_tso_segment
Accessing the hdr of an skb that was consumed already isn't
a good idea.
First ask if the skb is a QoS packet, then keep that data
on stack, and then consume the skb.
This was spotted by KASAN.
The index for the elements of the ACPI object we dereference
was static. This means that if we called the function twice
we wouldn't start from 3 again, but rather from the latest
index we reached in the previous call.
This was dutifully reported by KASAN.
Fix this.
Cc: [email protected] Fixes: 6996490501ed ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table") Signed-off-by: Emmanuel Grumbach <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
iwlwifi: don't unmap as page memory that was mapped as single
In order to remember how to unmap a memory (as single or
as page), we maintain a bit per Transmit Buffer (TBs) in
the meta data (structure iwl_cmd_meta).
We maintain a bitmap: 1 bit per TB.
If the TB is set, we will free the memory as a page.
This bitmap was never cleared. Fix this.
iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support
We erroneously added a check for FW API version 41 before sending
GEO_TX_POWER_LIMIT, but this was already implemented in version 38.
Additionally, it was cherry-picked to older versions, namely 17, 26
and 29, so check for those as well.
iwlwifi: mvm: fix possible out-of-bounds read when accessing lq_info
lq_info is an arary of size 2, active_tbl index is u8.
When accessing lq_info[1 - active_tbl], theoretically it's possible
that the access will be made to a negative index value.
iwlwifi: mvm: fix frame drop from the reordering buffer
An earlier patch made sure that the queues are not lagging
too far behind. This means that iwl_mvm_release_frames
should not be called with a head_sn too far behind NSSN.
Don't take the risk to change completely the entry
condition to iwl_mvm_release_frames, but don't update
the head_sn is the NSSN is more than 2048 packets ahead
of us. Since this just cannot be right. This means that
the scenario described here happened. We are queue 0.
Q:0 Q:1
head_sn: 0 -> 2047
head_sn: 2048
Lots of packets arrive:
head_sn: 2047 -> 2150
send NSSN_SYNC notification
Handle notification
from the firmware and
do NOT move the head_sn
back to 2048
Gregory Greenman [Sun, 30 Jun 2019 06:42:57 +0000 (09:42 +0300)]
iwlwifi: mvm: replace RS mutex with a spin_lock
The solution with the worker still had a bug, as in order
to get sta, rcu_read_lock should be used and thus no mutex
can be used inside iwl_mvm_rs_rate_init.
Also, spin_lock is a simpler solution, no need to spawn a
dedicated worker.
Gregory Greenman [Sun, 30 Jun 2019 06:18:15 +0000 (09:18 +0300)]
iwlwifi: mvm: send LQ command always ASYNC
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Colin Ian King [Mon, 1 Jul 2019 16:26:57 +0000 (17:26 +0100)]
iwlwifi: mvm: fix comparison of u32 variable with less than zero
The comparison of the u32 variable wgds_tbl_idx with less than zero is
always going to be false because it is unsigned. Fix this by making
wgds_tbl_idx a plain signed int.
Addresses-Coverity: ("Unsigned compared against 0") Fixes: 4fd445a2c855 ("iwlwifi: mvm: Add log information about SAR status") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
Johannes Berg [Thu, 27 Jun 2019 07:44:50 +0000 (09:44 +0200)]
iwlwifi: fix locking in delayed GTK setting
This code clearly never could have worked, since it locks
while already locked. Add an unlocked __iwl_mvm_mac_set_key()
variant that doesn't do locking to fix that.
iwlwifi: dbg_ini: move iwl_dbg_tlv_free outside of debugfs ifdef
The driver should call iwl_dbg_tlv_free even if debugfs is not defined
since ini mode does not depend on debugfs ifdef.
Signed-off-by: Shahar S Matityahu <[email protected]> Fixes: 68f6f492c4fa ("iwlwifi: trans: support loading ini TLVs from external file") Signed-off-by: Luca Coelho <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
projects / linux.git / log