Michał Mirosław [Tue, 22 Feb 2011 16:52:28 +0000 (16:52 +0000)]
net: avoid initial "Features changed" message
Avoid "Features changed" message and ndo_set_features call on device
registration caused by automatic enabling of GSO and GRO. Driver should
have enabled hardware offloads it set in features, so the ndo_set_features()
is not needed at registration time.
Michał Mirosław [Tue, 22 Feb 2011 16:52:28 +0000 (16:52 +0000)]
Fix "(unregistered net_device): Features changed" message
Fix netdev_update_features() messages on register time by moving
the call further in register_netdevice(). When
netdev->reg_state != NETREG_REGISTERED, netdev_name() returns
"(unregistered netdevice)" even if the dev's name is already filled.
Shawn Lin [Wed, 23 Feb 2011 04:32:34 +0000 (04:32 +0000)]
r6040: fix multicast operations
The original code does not work well when the number of mulitcast
address to handle is greater than MCAST_MAX. It only enable promiscous
mode instead of multicast hash table mode, so the hash table function
will not be activated and all multicast frames will be recieved in this
condition.
This patch fixes the following issues with the r6040 NIC operating in
multicast:
1) When the IFF_ALLMULTI flag is set, we should write 0xffff to the NIC
hash table registers to make it process multicast traffic.
2) When the number of multicast address to handle is smaller than
MCAST_MAX, we should use the NIC multicast registers MID1_{L,M,H}.
3) The hashing of the address was not correct, due to an invalid
substraction (15 - (crc & 0x0f)) instead of (crc & 0x0f) and an
incorrect crc algorithm (ether_crc_le) instead of (ether_crc).
4) If necessary, we should set HASH_EN flag in MCR0 to enable multicast
hash table function.
The dmaw_block is an enum and max_pay_load is u32. Therefore
sparse gives warning about comparison of unsigned and signed value.
Resolve by using min_t to force cast.
This implementation is based on work done by Juliusz Chroboczek
General SFB algorithm can be found in figure 14, page 15:
B[l][n] : L x N array of bins (L levels, N bins per level)
enqueue()
Calculate hash function values h{0}, h{1}, .. h{L-1}
Update bins at each level
for i = 0 to L - 1
if (B[i][h{i}].qlen > bin_size)
B[i][h{i}].p_mark += p_increment;
else if (B[i][h{i}].qlen == 0)
B[i][h{i}].p_mark -= p_decrement;
p_min = min(B[0][h{0}].p_mark ... B[L-1][h{L-1}].p_mark);
if (p_min == 1.0)
ratelimit();
else
mark/drop with probabilty p_min;
I did the adaptation of Juliusz code to meet current kernel standards,
and various changes to address previous comments :
Default flow classifier is the rxhash introduced by RPS in 2.6.35, but
we can use an external flow classifier if wanted.
tc qdisc add dev $DEV parent 1:11 handle 11: \
est 0.5sec 2sec sfb limit 128
tc filter add dev $DEV protocol ip parent 11: handle 3 \
flow hash keys dst divisor 1024
Notes:
1) SFB default child qdisc is pfifo_fast. It can be changed by another
qdisc but a child qdisc MUST not drop a packet previously queued. This
is because SFB needs to handle a dequeued packet in order to maintain
its virtual queue states. pfifo_head_drop or CHOKe should not be used.
2) ECN is enabled by default, unlike RED/CHOKe/GRED
Ajit Khaparde [Sun, 20 Feb 2011 11:41:53 +0000 (11:41 +0000)]
be2net: fix to ignore transparent vlan ids wrongly indicated by NIC
With transparent VLAN tagging, the ASIC wrongly indicates packets with VLAN ID.
Strip them off in the driver. The VLAN Tag to be stripped will be given to the host
as an async message.
Sujith Manoharan [Mon, 21 Feb 2011 11:37:12 +0000 (17:07 +0530)]
ath9k_hw: Fix power on reset
Commit "ath9k_hw: add an extra delay when reseting AR_RTC_RESET"
added an extra udelay to the reset routine. As the required
delay is already present, remove this.
Helmut Schaa [Sun, 20 Feb 2011 12:56:07 +0000 (13:56 +0100)]
Revert "rt2x00 : avoid timestamp for monitor injected frame."
This reverts commit e81e0aef32bfa7f593b14479b9c7eaa7196798ac "rt2x00 : avoid
timestamp for monitor injected frame." as it breaks proper timestamp insertion
into probe responses injected by hostapd for example.
Helmut Schaa [Sun, 20 Feb 2011 12:55:46 +0000 (13:55 +0100)]
rt2x00: Minor optimization for devices with RTS/CTS offload
Only devices that don't have RTS/CTS offload need to check for
IEEE80211_TX_RC_USE_RTS_CTS and IEEE80211_TX_RC_USE_CTS_PROTECT.
By swapping both conditions we keep the same number of needed conditionals
for devices without RTS/CTS offload but save one conditional on devices
with RTS/CTS offload.
RA-Jay Hung [Sun, 20 Feb 2011 12:55:25 +0000 (13:55 +0100)]
rt2x00: Fix rt2800 txpower setting to correct value
TX_PWR_CFG_* setting need to consider below cases
-compesate 20M/40M tx power delta for 2.4/5GHZ band
-limit maximum EIRP tx power to power_level of
regulatory requirement
RA-Jay Hung [Sun, 20 Feb 2011 12:54:52 +0000 (13:54 +0100)]
rt2x00: Add antenna setting for RT3070/RT3090/RT3390 with RX antenna diversity support
For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select
default antenna using gpio control way even if we do not turn on
antenna diversity feature.
Seperate the meaning of TX/RX chain and antenna. Some chips use
2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain
but may have 2 RX antennas to do antenna diversity.
Larry Finger [Sat, 19 Feb 2011 22:29:07 +0000 (16:29 -0600)]
rtlwifi: Modify wifi.h for rtl8192cu
Further merge of parameters needed for rtl8192cu. In addition,
some changes needed for rtl8192se and rtl8192de are included
and additional Hungarian notation is removed.
Larry Finger [Sat, 19 Feb 2011 22:28:52 +0000 (16:28 -0600)]
rtlwifi: Make changes in rtlwifi/rtl8192ce/def.h to support rtl8192cu
This change modifies rtlwifi/rtl8192ce/def.h to handle rtl8192cu. In
addition, a couple of routines needed for both drivers are converted
to be inline.
When op_flush() is called with no drop (drop=false), the driver
tries to tx as many frames as possible in about 100ms on every
hw queue. During this time period frames from sw queue are also
scheduled on to respective hw queue.
Randy Dunlap [Sat, 19 Feb 2011 01:25:36 +0000 (17:25 -0800)]
wl12xx: fix sdio_test kconfig/build errors
The wl12xx sdio_test code uses wl12xx_get_platform_data, which is
only present when WL12*_SDIO is enabled, so make WL12XX_SDIO_TEST
depend on WL12XX_SDIO so that the needed interface will be present.
sdio_test.c:(.devinit.text+0x13178): undefined reference to `wl12xx_get_platform_data'
Shan Wei [Sat, 19 Feb 2011 21:57:26 +0000 (21:57 +0000)]
sctp: fix compile warnings in sctp_tsnmap_num_gabs
net/sctp/tsnmap.c: In function ‘sctp_tsnmap_num_gabs’:
net/sctp/tsnmap.c:347: warning: ‘start’ may be used uninitialized in this function
net/sctp/tsnmap.c:347: warning: ‘end’ may be used uninitialized in this function
Jiri Bohac [Thu, 17 Feb 2011 13:12:08 +0000 (13:12 +0000)]
sctp: fix reporting of unknown parameters
commit 5fa782c2f5ef6c2e4f04d3e228412c9b4a4c8809 re-worked the
handling of unknown parameters. sctp_init_cause_fixed() can now
return -ENOSPC if there is not enough tailroom in the error
chunk skb. When this happens, the error header is not appended to
the error chunk. In that case, the payload of the unknown parameter
should not be appended either.
John Fastabend [Fri, 18 Feb 2011 13:30:17 +0000 (13:30 +0000)]
net: dcb: match dcb_app protocol field with 802.1Qaz spec
The dcb_app protocol field is a __u32 however the 802.1Qaz
specification defines it as a 16 bit field. This patch brings
the structure inline with the spec making it a __u16.
Eric Dumazet [Fri, 18 Feb 2011 22:35:56 +0000 (22:35 +0000)]
tcp: fix inet_twsk_deschedule()
Eric W. Biederman reported a lockdep splat in inet_twsk_deschedule()
This is caused by inet_twsk_purge(), run from process context,
and commit 575f4cd5a5b6394577 (net: Use rcu lookups in inet_twsk_purge.)
removed the BH disabling that was necessary.
Add the BH disabling but fine grained, right before calling
inet_twsk_deschedule(), instead of whole function.
With help from Linus Torvalds and Eric W. Biederman
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
net: deinit automatic LIST_HEAD
net: dont leave active on stack LIST_HEAD
net: provide default_advmss() methods to blackhole dst_ops
tg3: Restrict phy ioctl access
drivers/net: Call netif_carrier_off at the end of the probe
ixgbe: work around for DDP last buffer size
ixgbe: fix panic due to uninitialised pointer
e1000e: flush all writebacks before unload
e1000e: check down flag in tasks
isdn: hisax: Use l2headersize() instead of dup (and buggy) func.
arp_notify: unconditionally send gratuitous ARP for NETDEV_NOTIFY_PEERS.
cxgb4vf: Use defined Mailbox Timeout
cxgb4vf: Quiesce Virtual Interfaces on shutdown ...
cxgb4vf: Behave properly when CONFIG_DEBUG_FS isn't defined ...
cxgb4vf: Check driver parameters in the right place ...
pch_gbe: Fix the MAC Address load issue.
iwlwifi: Delete iwl3945_good_plcp_health.
net/can/softing: make CAN_SOFTING_CS depend on CAN_SOFTING
netfilter: nf_iterate: fix incorrect RCU usage
pch_gbe: Fix the issue that the receiving data is not normal.
...
Vivek Natarajan [Fri, 18 Feb 2011 10:39:51 +0000 (16:09 +0530)]
ath9k_htc: Fix a compilation warning.
Initialize caldata to avoid compilation warning.
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_main.o
drivers/net/wireless/ath/ath9k/htc_drv_main.c: In function ‘ath9k_htc_config’:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: warning: ‘caldata’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: note: ‘caldata’ was declared here
projects / linux.git / log