]> Git Repo - linux.git/log
linux.git
3 months agoi2c: nomadik: support >=1MHz speed modes
Théo Lebrun [Wed, 9 Oct 2024 14:01:12 +0000 (16:01 +0200)]
i2c: nomadik: support >=1MHz speed modes

 - BRCR value must go into the BRCR1 field when in high-speed mode.
   It goes into BRCR2 otherwise.

 - Remove fallback to standard mode if priv->sm > I2C_FREQ_MODE_FAST.

 - Set SM properly in probe; previously it only checked STANDARD versus
   FAST. Now we set STANDARD, FAST, FAST_PLUS or HIGH_SPEED.

 - Remove all comment sections saying we only support low-speeds.

Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Théo Lebrun <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agoi2c: nomadik: fix BRCR computation
Théo Lebrun [Wed, 9 Oct 2024 14:01:11 +0000 (16:01 +0200)]
i2c: nomadik: fix BRCR computation

Current BRCR computation is:

    brcr = floor(i2cclk / (clkfreq * div))

With brcr: "baud rate counter", an internal clock divider,
 and i2cclk: input clock rate (24MHz, 38.4MHz or 48MHz),
 and clkfreq: desired bus rate,
 and div: speed-mode dependent divider (2 for standard, 3 otherwise).

Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
  then brcr = floor(48MHz / (3.4MHz * 3)) = 4
   and resulting bus rate = 48MHz / (4 * 3) = 4MHz

Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
  then brcr = floor(38.4MHz / (1.0MHz * 3)) = 12
   and resulting bus rate = 38.4MHz / (12 * 3) = 1066kHz

The current computation means we always pick the smallest divider that
gives a bus rate above target. We should instead pick the largest
divider that gives a bus rate below target, using:

    brcr = floor(i2cclk / (clkfreq * div)) + 1

If we redo the above examples:

Assume i2cclk=48MHz, clkfreq=3.4MHz, div=3,
  then brcr = floor(48MHz / (3.4MHz * 3)) + 1 = 5
   and resulting bus rate = 48MHz / (5 * 3) = 3.2MHz

Assume i2cclk=38.4MHz, clkfreq=1.0MHz, div=3,
  then brcr = floor(38.4MHz / (1.0MHz * 3)) + 1 = 13
   and resulting bus rate = 38.4MHz / (13 * 3) = 985kHz

In kernel C code, floor(x)   is DIV_ROUND_DOWN() and,
                  floor(x)+1 is DIV_ROUND_UP().

This is much less of an issue with slower bus rates (ie those currently
supported), because the gap from one divider to the next is much
smaller. It however keeps us from always using bus rates superior to
the target.

This fix is required for later on supporting faster bus rates:
I2C_FREQ_MODE_FAST_PLUS (1MHz) and I2C_FREQ_MODE_HIGH_SPEED (3.4MHz).

Signed-off-by: Théo Lebrun <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agoi2c: nomadik: support Mobileye EyeQ6H I2C controller
Théo Lebrun [Wed, 9 Oct 2024 14:01:10 +0000 (16:01 +0200)]
i2c: nomadik: support Mobileye EyeQ6H I2C controller

Add EyeQ6H support to the nmk-i2c AMBA driver. It shares the same quirk
as EyeQ5: the memory bus only supports 32-bit accesses. Avoid writeb()
and readb() by reusing the same `priv->has_32b_bus` flag.

It does NOT need to write speed-mode specific value into a register;
therefore it does not depend on the mobileye,olb DT property.

Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Théo Lebrun <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agoi2c: nomadik: switch from of_device_is_compatible() to of_match_device()
Théo Lebrun [Wed, 9 Oct 2024 14:01:09 +0000 (16:01 +0200)]
i2c: nomadik: switch from of_device_is_compatible() to of_match_device()

Compatible-specific behavior is implemented using a if-condition on the
return value from of_device_is_compatible(), from probe. It does not
scale well when compatible number increases. Switch to using a match
table and a call to of_match_device().

We DO NOT attach a .of_match_table field to our amba driver, as we do
not use the table to match our driver to devices.

Sort probe variable declarations in reverse christmas tree to try and
introduce some logic into the ordering.

Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Théo Lebrun <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agodt-bindings: i2c: nomadik: support 400kHz < clock-frequency <= 3.4MHz
Théo Lebrun [Wed, 9 Oct 2024 14:01:08 +0000 (16:01 +0200)]
dt-bindings: i2c: nomadik: support 400kHz < clock-frequency <= 3.4MHz

Hardware is not limited to 400kHz, its documentation does mention how to
configure it for high-speed (a specific Speed-Mode enum value and
a different bus rate clock divider register to be used).

Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Théo Lebrun <[email protected]>
Reviewed-by: Rob Herring (Arm) <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agodt-bindings: i2c: nomadik: add mobileye,eyeq6h-i2c bindings
Théo Lebrun [Wed, 9 Oct 2024 14:01:07 +0000 (16:01 +0200)]
dt-bindings: i2c: nomadik: add mobileye,eyeq6h-i2c bindings

After EyeQ5, it is time for Mobileye EyeQ6H to reuse the Nomadik I2C
controller. Add a specific compatible because its HW integration is
slightly different from EyeQ5.

Do NOT add an example as it looks like EyeQ5 from a DT standpoint
(without the mobileye,olb property).

Reviewed-by: Linus Walleij <[email protected]>
Signed-off-by: Théo Lebrun <[email protected]>
Reviewed-by: Rob Herring (Arm) <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agodt-bindings: i2c: mv64xxx: Add Allwinner A523 compatible string
Andre Przywara [Mon, 11 Nov 2024 01:30:24 +0000 (01:30 +0000)]
dt-bindings: i2c: mv64xxx: Add Allwinner A523 compatible string

The I2C controller IP used in the Allwinner A523/T527 SoCs is
compatible with the ones used in the other recent Allwinner SoCs.

Add the A523 specific compatible string to the list of existing names
falling back to the allwinner,sun8i-v536-i2c string.

Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agoi2c: designware: Add ACPI HID for DWAPB I2C controller on FUJITSU-MONAKA
Yoshihiro Furudera [Thu, 24 Oct 2024 07:15:53 +0000 (07:15 +0000)]
i2c: designware: Add ACPI HID for DWAPB I2C controller on FUJITSU-MONAKA

Enable DWAPB I2C controller support on FUJITSU-MONAKA.
This will be used in the FUJITSU-MONAKA server scheduled
for shipment in 2027.

The DSDT information obtained when verified using an
in-house simulator is presented below.

     Device (SMB0)
     {
         Name (_HID, "FUJI200B")  // _HID: Hardware ID
         Name (_UID, Zero)  // _UID: Unique ID
         ...
         Name (_CRS, ResourceTemplate ()
         {
             Memory32Fixed (ReadWrite,
                 0x2A4B0000,         // Address Base
                 0x00010000,         // Address Length
                 )
             Interrupt (ResourceConsumer, Level, ActiveHigh, Exclusive, ,, )
             {
                 0x00000159,
             }
         })
         ...
     }

The expression SMB0 is used to indicate SMBus HC#0,
a string of up to four characters.

Created the SMB0 object according to the following
specifications:

ACPI Specification
13.2. Accessing the SMBus from ASL Code
https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/13_ACPI_System_Mgmt_Bus_Interface_Spec/accessing-the-smbus-from-asl-code.html

IPMI Specification
Example 4: SSIF Interface(P574)
https://www.intel.co.jp/content/www/jp/ja/products/docs/servers/ipmi/ipmi-second-gen-interface-spec-v2-rev1-1.html

Signed-off-by: Yoshihiro Furudera <[email protected]>
Reviewed-by: Andy Shevchenko <[email protected]>
Acked-by: Jarkko Nikula <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agoi2c: qup: use generic device property accessors
Bartosz Golaszewski [Tue, 8 Oct 2024 16:09:47 +0000 (18:09 +0200)]
i2c: qup: use generic device property accessors

There's no reason for this driver to use OF-specific property helpers.
Drop the last one in favor of the generic variant and no longer include
of.h.

Signed-off-by: Bartosz Golaszewski <[email protected]>
Reviewed-by: Neil Armstrong <[email protected]>
Signed-off-by: Andi Shyti <[email protected]>
Signed-off-by: Wolfram Sang <[email protected]>
3 months agoMerge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Sun, 24 Nov 2024 00:00:50 +0000 (16:00 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm

Pull kvm updates from Paolo Bonzini:
 "The biggest change here is eliminating the awful idea that KVM had of
  essentially guessing which pfns are refcounted pages.

  The reason to do so was that KVM needs to map both non-refcounted
  pages (for example BARs of VFIO devices) and VM_PFNMAP/VM_MIXMEDMAP
  VMAs that contain refcounted pages.

  However, the result was security issues in the past, and more recently
  the inability to map VM_IO and VM_PFNMAP memory that _is_ backed by
  struct page but is not refcounted. In particular this broke virtio-gpu
  blob resources (which directly map host graphics buffers into the
  guest as "vram" for the virtio-gpu device) with the amdgpu driver,
  because amdgpu allocates non-compound higher order pages and the tail
  pages could not be mapped into KVM.

  This requires adjusting all uses of struct page in the
  per-architecture code, to always work on the pfn whenever possible.
  The large series that did this, from David Stevens and Sean
  Christopherson, also cleaned up substantially the set of functions
  that provided arch code with the pfn for a host virtual addresses.

  The previous maze of twisty little passages, all different, is
  replaced by five functions (__gfn_to_page, __kvm_faultin_pfn, the
  non-__ versions of these two, and kvm_prefetch_pages) saving almost
  200 lines of code.

  ARM:

   - Support for stage-1 permission indirection (FEAT_S1PIE) and
     permission overlays (FEAT_S1POE), including nested virt + the
     emulated page table walker

   - Introduce PSCI SYSTEM_OFF2 support to KVM + client driver. This
     call was introduced in PSCIv1.3 as a mechanism to request
     hibernation, similar to the S4 state in ACPI

   - Explicitly trap + hide FEAT_MPAM (QoS controls) from KVM guests. As
     part of it, introduce trivial initialization of the host's MPAM
     context so KVM can use the corresponding traps

   - PMU support under nested virtualization, honoring the guest
     hypervisor's trap configuration and event filtering when running a
     nested guest

   - Fixes to vgic ITS serialization where stale device/interrupt table
     entries are not zeroed when the mapping is invalidated by the VM

   - Avoid emulated MMIO completion if userspace has requested
     synchronous external abort injection

   - Various fixes and cleanups affecting pKVM, vCPU initialization, and
     selftests

  LoongArch:

   - Add iocsr and mmio bus simulation in kernel.

   - Add in-kernel interrupt controller emulation.

   - Add support for virtualization extensions to the eiointc irqchip.

  PPC:

   - Drop lingering and utterly obsolete references to PPC970 KVM, which
     was removed 10 years ago.

   - Fix incorrect documentation references to non-existing ioctls

  RISC-V:

   - Accelerate KVM RISC-V when running as a guest

   - Perf support to collect KVM guest statistics from host side

  s390:

   - New selftests: more ucontrol selftests and CPU model sanity checks

   - Support for the gen17 CPU model

   - List registers supported by KVM_GET/SET_ONE_REG in the
     documentation

  x86:

   - Cleanup KVM's handling of Accessed and Dirty bits to dedup code,
     improve documentation, harden against unexpected changes.

     Even if the hardware A/D tracking is disabled, it is possible to
     use the hardware-defined A/D bits to track if a PFN is Accessed
     and/or Dirty, and that removes a lot of special cases.

   - Elide TLB flushes when aging secondary PTEs, as has been done in
     x86's primary MMU for over 10 years.

   - Recover huge pages in-place in the TDP MMU when dirty page logging
     is toggled off, instead of zapping them and waiting until the page
     is re-accessed to create a huge mapping. This reduces vCPU jitter.

   - Batch TLB flushes when dirty page logging is toggled off. This
     reduces the time it takes to disable dirty logging by ~3x.

   - Remove the shrinker that was (poorly) attempting to reclaim shadow
     page tables in low-memory situations.

   - Clean up and optimize KVM's handling of writes to
     MSR_IA32_APICBASE.

   - Advertise CPUIDs for new instructions in Clearwater Forest

   - Quirk KVM's misguided behavior of initialized certain feature MSRs
     to their maximum supported feature set, which can result in KVM
     creating invalid vCPU state. E.g. initializing PERF_CAPABILITIES to
     a non-zero value results in the vCPU having invalid state if
     userspace hides PDCM from the guest, which in turn can lead to
     save/restore failures.

   - Fix KVM's handling of non-canonical checks for vCPUs that support
     LA57 to better follow the "architecture", in quotes because the
     actual behavior is poorly documented. E.g. most MSR writes and
     descriptor table loads ignore CR4.LA57 and operate purely on
     whether the CPU supports LA57.

   - Bypass the register cache when querying CPL from kvm_sched_out(),
     as filling the cache from IRQ context is generally unsafe; harden
     the cache accessors to try to prevent similar issues from occuring
     in the future. The issue that triggered this change was already
     fixed in 6.12, but was still kinda latent.

   - Advertise AMD_IBPB_RET to userspace, and fix a related bug where
     KVM over-advertises SPEC_CTRL when trying to support cross-vendor
     VMs.

   - Minor cleanups

   - Switch hugepage recovery thread to use vhost_task.

     These kthreads can consume significant amounts of CPU time on
     behalf of a VM or in response to how the VM behaves (for example
     how it accesses its memory); therefore KVM tried to place the
     thread in the VM's cgroups and charge the CPU time consumed by that
     work to the VM's container.

     However the kthreads did not process SIGSTOP/SIGCONT, and therefore
     cgroups which had KVM instances inside could not complete freezing.

     Fix this by replacing the kthread with a PF_USER_WORKER thread, via
     the vhost_task abstraction. Another 100+ lines removed, with
     generally better behavior too like having these threads properly
     parented in the process tree.

   - Revert a workaround for an old CPU erratum (Nehalem/Westmere) that
     didn't really work; there was really nothing to work around anyway:
     the broken patch was meant to fix nested virtualization, but the
     PERF_GLOBAL_CTRL MSR is virtualized and therefore unaffected by the
     erratum.

   - Fix 6.12 regression where CONFIG_KVM will be built as a module even
     if asked to be builtin, as long as neither KVM_INTEL nor KVM_AMD is
     'y'.

  x86 selftests:

   - x86 selftests can now use AVX.

  Documentation:

   - Use rST internal links

   - Reorganize the introduction to the API document

  Generic:

   - Protect vcpu->pid accesses outside of vcpu->mutex with a rwlock
     instead of RCU, so that running a vCPU on a different task doesn't
     encounter long due to having to wait for all CPUs become quiescent.

     In general both reads and writes are rare, but userspace that
     supports confidential computing is introducing the use of "helper"
     vCPUs that may jump from one host processor to another. Those will
     be very happy to trigger a synchronize_rcu(), and the effect on
     performance is quite the disaster"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (298 commits)
  KVM: x86: Break CONFIG_KVM_X86's direct dependency on KVM_INTEL || KVM_AMD
  KVM: x86: add back X86_LOCAL_APIC dependency
  Revert "KVM: VMX: Move LOAD_IA32_PERF_GLOBAL_CTRL errata handling out of setup_vmcs_config()"
  KVM: x86: switch hugepage recovery thread to vhost_task
  KVM: x86: expose MSR_PLATFORM_INFO as a feature MSR
  x86: KVM: Advertise CPUIDs for new instructions in Clearwater Forest
  Documentation: KVM: fix malformed table
  irqchip/loongson-eiointc: Add virt extension support
  LoongArch: KVM: Add irqfd support
  LoongArch: KVM: Add PCHPIC user mode read and write functions
  LoongArch: KVM: Add PCHPIC read and write functions
  LoongArch: KVM: Add PCHPIC device support
  LoongArch: KVM: Add EIOINTC user mode read and write functions
  LoongArch: KVM: Add EIOINTC read and write functions
  LoongArch: KVM: Add EIOINTC device support
  LoongArch: KVM: Add IPI user mode read and write function
  LoongArch: KVM: Add IPI read and write function
  LoongArch: KVM: Add IPI device support
  LoongArch: KVM: Add iocsr and mmio bus simulation in kernel
  KVM: arm64: Pass on SVE mapping failures
  ...

3 months agoMerge tag 'powerpc-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc...
Linus Torvalds [Sat, 23 Nov 2024 18:44:31 +0000 (10:44 -0800)]
Merge tag 'powerpc-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:

 - Rework kfence support for the HPT MMU to work on systems with >= 16TB
   of RAM.

 - Remove the powerpc "maple" platform, used by the "Yellow Dog
   Powerstation".

 - Add support for DYNAMIC_FTRACE_WITH_CALL_OPS,
   DYNAMIC_FTRACE_WITH_DIRECT_CALLS & BPF Trampolines.

 - Add support for running KVM nested guests on Power11.

 - Other small features, cleanups and fixes.

Thanks to Amit Machhiwal, Arnd Bergmann, Christophe Leroy, Costa
Shulyupin, David Hunter, David Wang, Disha Goel, Gautam Menghani, Geert
Uytterhoeven, Hari Bathini, Julia Lawall, Kajol Jain, Keith Packard,
Lukas Bulwahn, Madhavan Srinivasan, Markus Elfring, Michal Suchanek,
Ming Lei, Mukesh Kumar Chaurasiya, Nathan Chancellor, Naveen N Rao,
Nicholas Piggin, Nysal Jan K.A, Paulo Miguel Almeida, Pavithra Prakash,
Ritesh Harjani (IBM), Rob Herring (Arm), Sachin P Bappalige, Shen
Lichuan, Simon Horman, Sourabh Jain, Thomas Weißschuh, Thorsten Blum,
Thorsten Leemhuis, Venkat Rao Bagalkote, Zhang Zekun, and zhang jiao.

* tag 'powerpc-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (89 commits)
  EDAC/powerpc: Remove PPC_MAPLE drivers
  powerpc/perf: Add per-task/process monitoring to vpa_pmu driver
  powerpc/kvm: Add vpa latency counters to kvm_vcpu_arch
  docs: ABI: sysfs-bus-event_source-devices-vpa-pmu: Document sysfs event format entries for vpa_pmu
  powerpc/perf: Add perf interface to expose vpa counters
  MAINTAINERS: powerpc: Mark Maddy as "M"
  powerpc/Makefile: Allow overriding CPP
  powerpc-km82xx.c: replace of_node_put() with __free
  ps3: Correct some typos in comments
  powerpc/kexec: Fix return of uninitialized variable
  macintosh: Use common error handling code in via_pmu_led_init()
  powerpc/powermac: Use of_property_match_string() in pmac_has_backlight_type()
  powerpc: remove dead config options for MPC85xx platform support
  powerpc/xive: Use cpumask_intersects()
  selftests/powerpc: Remove the path after initialization.
  powerpc/xmon: symbol lookup length fixed
  powerpc/ep8248e: Use %pa to format resource_size_t
  powerpc/ps3: Reorganize kerneldoc parameter names
  KVM: PPC: Book3S HV: Fix kmv -> kvm typo
  powerpc/sstep: make emulate_vsx_load and emulate_vsx_store static
  ...

3 months agoMerge tag 'mm-stable-2024-11-18-19-27' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Sat, 23 Nov 2024 17:58:07 +0000 (09:58 -0800)]
Merge tag 'mm-stable-2024-11-18-19-27' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull MM updates from Andrew Morton:

 - The series "zram: optimal post-processing target selection" from
   Sergey Senozhatsky improves zram's post-processing selection
   algorithm. This leads to improved memory savings.

 - Wei Yang has gone to town on the mapletree code, contributing several
   series which clean up the implementation:
- "refine mas_mab_cp()"
- "Reduce the space to be cleared for maple_big_node"
- "maple_tree: simplify mas_push_node()"
- "Following cleanup after introduce mas_wr_store_type()"
- "refine storing null"

 - The series "selftests/mm: hugetlb_fault_after_madv improvements" from
   David Hildenbrand fixes this selftest for s390.

 - The series "introduce pte_offset_map_{ro|rw}_nolock()" from Qi Zheng
   implements some rationaizations and cleanups in the page mapping
   code.

 - The series "mm: optimize shadow entries removal" from Shakeel Butt
   optimizes the file truncation code by speeding up the handling of
   shadow entries.

 - The series "Remove PageKsm()" from Matthew Wilcox completes the
   migration of this flag over to being a folio-based flag.

 - The series "Unify hugetlb into arch_get_unmapped_area functions" from
   Oscar Salvador implements a bunch of consolidations and cleanups in
   the hugetlb code.

 - The series "Do not shatter hugezeropage on wp-fault" from Dev Jain
   takes away the wp-fault time practice of turning a huge zero page
   into small pages. Instead we replace the whole thing with a THP. More
   consistent cleaner and potentiall saves a large number of pagefaults.

 - The series "percpu: Add a test case and fix for clang" from Andy
   Shevchenko enhances and fixes the kernel's built in percpu test code.

 - The series "mm/mremap: Remove extra vma tree walk" from Liam Howlett
   optimizes mremap() by avoiding doing things which we didn't need to
   do.

 - The series "Improve the tmpfs large folio read performance" from
   Baolin Wang teaches tmpfs to copy data into userspace at the folio
   size rather than as individual pages. A 20% speedup was observed.

 - The series "mm/damon/vaddr: Fix issue in
   damon_va_evenly_split_region()" fro Zheng Yejian fixes DAMON
   splitting.

 - The series "memcg-v1: fully deprecate charge moving" from Shakeel
   Butt removes the long-deprecated memcgv2 charge moving feature.

 - The series "fix error handling in mmap_region() and refactor" from
   Lorenzo Stoakes cleanup up some of the mmap() error handling and
   addresses some potential performance issues.

 - The series "x86/module: use large ROX pages for text allocations"
   from Mike Rapoport teaches x86 to use large pages for
   read-only-execute module text.

 - The series "page allocation tag compression" from Suren Baghdasaryan
   is followon maintenance work for the new page allocation profiling
   feature.

 - The series "page->index removals in mm" from Matthew Wilcox remove
   most references to page->index in mm/. A slow march towards shrinking
   struct page.

 - The series "damon/{self,kunit}tests: minor fixups for DAMON debugfs
   interface tests" from Andrew Paniakin performs maintenance work for
   DAMON's self testing code.

 - The series "mm: zswap swap-out of large folios" from Kanchana Sridhar
   improves zswap's batching of compression and decompression. It is a
   step along the way towards using Intel IAA hardware acceleration for
   this zswap operation.

 - The series "kasan: migrate the last module test to kunit" from
   Sabyrzhan Tasbolatov completes the migration of the KASAN built-in
   tests over to the KUnit framework.

 - The series "implement lightweight guard pages" from Lorenzo Stoakes
   permits userapace to place fault-generating guard pages within a
   single VMA, rather than requiring that multiple VMAs be created for
   this. Improved efficiencies for userspace memory allocators are
   expected.

 - The series "memcg: tracepoint for flushing stats" from JP Kobryn uses
   tracepoints to provide increased visibility into memcg stats flushing
   activity.

 - The series "zram: IDLE flag handling fixes" from Sergey Senozhatsky
   fixes a zram buglet which potentially affected performance.

 - The series "mm: add more kernel parameters to control mTHP" from
   Maíra Canal enhances our ability to control/configuremultisize THP
   from the kernel boot command line.

 - The series "kasan: few improvements on kunit tests" from Sabyrzhan
   Tasbolatov has a couple of fixups for the KASAN KUnit tests.

 - The series "mm/list_lru: Split list_lru lock into per-cgroup scope"
   from Kairui Song optimizes list_lru memory utilization when lockdep
   is enabled.

* tag 'mm-stable-2024-11-18-19-27' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (215 commits)
  cma: enforce non-zero pageblock_order during cma_init_reserved_mem()
  mm/kfence: add a new kunit test test_use_after_free_read_nofault()
  zram: fix NULL pointer in comp_algorithm_show()
  memcg/hugetlb: add hugeTLB counters to memcg
  vmstat: call fold_vm_zone_numa_events() before show per zone NUMA event
  mm: mmap_lock: check trace_mmap_lock_$type_enabled() instead of regcount
  zram: ZRAM_DEF_COMP should depend on ZRAM
  MAINTAINERS/MEMORY MANAGEMENT: add document files for mm
  Docs/mm/damon: recommend academic papers to read and/or cite
  mm: define general function pXd_init()
  kmemleak: iommu/iova: fix transient kmemleak false positive
  mm/list_lru: simplify the list_lru walk callback function
  mm/list_lru: split the lock to per-cgroup scope
  mm/list_lru: simplify reparenting and initial allocation
  mm/list_lru: code clean up for reparenting
  mm/list_lru: don't export list_lru_add
  mm/list_lru: don't pass unnecessary key parameters
  kasan: add kunit tests for kmalloc_track_caller, kmalloc_node_track_caller
  kasan: change kasan_atomics kunit test as KUNIT_CASE_SLOW
  kasan: use EXPORT_SYMBOL_IF_KUNIT to export symbols
  ...

3 months agoMerge tag '6.13-rc-part1-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Linus Torvalds [Sat, 23 Nov 2024 05:54:14 +0000 (21:54 -0800)]
Merge tag '6.13-rc-part1-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6

Pull smb client updates from Steve French:

 - Fix two SMB3.1.1 POSIX Extensions problems

 - Fixes for special file handling (symlinks and FIFOs)

 - Improve compounding

 - Four cleanup patches

 - Fix use after free in signing

 - Add support for handling namespaces for reconnect related upcalls
   (e.g. for DNS names resolution and auth)

 - Fix various directory lease problems (directory entry caching),
   including some important potential use after frees

* tag '6.13-rc-part1-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  smb: prevent use-after-free due to open_cached_dir error paths
  smb: Don't leak cfid when reconnect races with open_cached_dir
  smb: client: handle max length for SMB symlinks
  smb: client: get rid of bounds check in SMB2_ioctl_init()
  smb: client: improve compound padding in encryption
  smb3: request handle caching when caching directories
  cifs: Recognize SFU char/block devices created by Windows NFS server on Windows Server <<2012
  CIFS: New mount option for cifs.upcall namespace resolution
  smb/client: Prevent error pointer dereference
  fs/smb/client: implement chmod() for SMB3 POSIX Extensions
  smb: cached directories can be more than root file handle
  smb: client: fix use-after-free of signing key
  smb: client: Use str_yes_no() helper function
  smb: client: memcpy() with surrounding object base address
  cifs: Remove pre-historic unused CIFSSMBCopy

3 months agoMerge tag 'ovl-update-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayf...
Linus Torvalds [Sat, 23 Nov 2024 04:55:42 +0000 (20:55 -0800)]
Merge tag 'ovl-update-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs

Pull overlayfs updates from Amir Goldstein:

 - Fix a syzbot reported NULL pointer deref with bfs lower layers

 - Fix a copy up failure of large file from lower fuse fs

 - Followup cleanup of backing_file API from Miklos

 - Introduction and use of revert/override_creds_light() helpers, that
   were suggested by Christian as a mitigation to cache line bouncing
   and false sharing of fields in overlayfs creator_cred long lived
   struct cred copy.

 - Store up to two backing file references (upper and lower) in an
   ovl_file container instead of storing a single backing file in
   file->private_data.

   This is used to avoid the practice of opening a short lived backing
   file for the duration of some file operations and to avoid the
   specialized use of FDPUT_FPUT in such occasions, that was getting in
   the way of Al's fd_file() conversions.

* tag 'ovl-update-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
  ovl: Filter invalid inodes with missing lookup function
  ovl: convert ovl_real_fdget() callers to ovl_real_file()
  ovl: convert ovl_real_fdget_path() callers to ovl_real_file_path()
  ovl: store upper real file in ovl_file struct
  ovl: allocate a container struct ovl_file for ovl private context
  ovl: do not open non-data lower file for fsync
  ovl: Optimize override/revert creds
  ovl: pass an explicit reference of creators creds to callers
  ovl: use wrapper ovl_revert_creds()
  fs/backing-file: Convert to revert/override_creds_light()
  cred: Add a light version of override/revert_creds()
  backing-file: clean up the API
  ovl: properly handle large files in ovl_security_fileattr

3 months agoMerge tag 'unicode-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krisma...
Linus Torvalds [Sat, 23 Nov 2024 04:50:55 +0000 (20:50 -0800)]
Merge tag 'unicode-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode

Pull unicode updates from Gabriel Krisman Bertazi:

 - constify a read-only struct (Thomas Weißschuh)

 - fix the error path of unicode_load, avoiding a possible kernel oops
   if it fails to find the unicode module (André Almeida)

 - documentation fix, updating a filename in the README (Gan Jie)

 - add the link of my tree to MAINTAINERS (André Almeida)

* tag 'unicode-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krisman/unicode:
  MAINTAINERS: Add Unicode tree
  unicode: change the reference of database file
  unicode: Fix utf8_load() error path
  unicode: constify utf8 data table

3 months agoMerge tag 'sysctl-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl...
Linus Torvalds [Sat, 23 Nov 2024 04:36:11 +0000 (20:36 -0800)]
Merge tag 'sysctl-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl

Pull sysctl updates from Joel Granados:
 "sysctl ctl_table constification:

   - Constifying ctl_table structs prevents the modification of
     proc_handler function pointers. All ctl_table struct arguments are
     const qualified in the sysctl API in such a way that the ctl_table
     arrays being defined elsewhere and passed through sysctl can be
     constified one-by-one.

     We kick the constification off by qualifying user_table in
     kernel/ucount.c and expect all the ctl_tables to be constified in
     the coming releases.

  Misc fixes:

   - Adjust comments in two places to better reflect the code

   - Remove superfluous dput calls

   - Remove Luis from sysctl maintainership

   - Replace comments about holding a lock with calls to
     lockdep_assert_held"

* tag 'sysctl-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl:
  sysctl: Reduce dput(child) calls in proc_sys_fill_cache()
  sysctl: Reorganize kerneldoc parameter names
  ucounts: constify sysctl table user_table
  sysctl: update comments to new registration APIs
  MAINTAINERS: remove me from sysctl
  sysctl: Convert locking comments to lockdep assertions
  const_structs.checkpatch: add ctl_table
  sysctl: make internal ctl_tables const
  sysctl: allow registration of const struct ctl_table
  sysctl: move internal interfaces to const struct ctl_table
  bpf: Constify ctl_table argument of filter function

3 months agoMerge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Linus Torvalds [Sat, 23 Nov 2024 04:03:57 +0000 (20:03 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma

Pull rdma updates from Jason Gunthorpe:
 "Seveal fixes scattered across the drivers and a few new features:

   - Minor updates and bug fixes to hfi1, efa, iopob, bnxt, hns

   - Force disassociate the userspace FD when hns does an async reset

   - bnxt new features for optimized modify QP to skip certain stayes,
     CQ coalescing, better debug dumping

   - mlx5 new data placement ordering feature

   - Faster destruction of mlx5 devx HW objects

   - Improvements to RDMA CM mad handling"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (51 commits)
  RDMA/bnxt_re: Correct the sequence of device suspend
  RDMA/bnxt_re: Use the default mode of congestion control
  RDMA/bnxt_re: Support different traffic class
  IB/cm: Rework sending DREQ when destroying a cm_id
  IB/cm: Do not hold reference on cm_id unless needed
  IB/cm: Explicitly mark if a response MAD is a retransmission
  RDMA/mlx5: Move events notifier registration to be after device registration
  RDMA/bnxt_re: Cache MSIx info to a local structure
  RDMA/bnxt_re: Refurbish CQ to NQ hash calculation
  RDMA/bnxt_re: Refactor NQ allocation
  RDMA/bnxt_re: Fail probe early when not enough MSI-x vectors are reserved
  RDMA/hns: Fix different dgids mapping to the same dip_idx
  RDMA/bnxt_re: Add set_func_resources support for P5/P7 adapters
  RDMA/bnxt_re: Enhance RoCE SRIOV resource configuration design
  bnxt_en: Add support for RoCE sriov configuration
  RDMA/hns: Fix NULL pointer derefernce in hns_roce_map_mr_sg()
  RDMA/hns: Fix out-of-order issue of requester when setting FENCE
  RDMA/nldev: Add IB device and net device rename events
  RDMA/mlx5: Add implementation for ufile_hw_cleanup device operation
  RDMA/core: Move ib_uverbs_file struct to uverbs_types.h
  ...

3 months agoMerge tag 'iommu-updates-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 23 Nov 2024 03:55:10 +0000 (19:55 -0800)]
Merge tag 'iommu-updates-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux

Pull iommu updates from Joerg Roedel:
 "Core Updates:
   - Convert call-sites using iommu_domain_alloc() to more specific
     versions and remove function
   - Introduce iommu_paging_domain_alloc_flags()
   - Extend support for allocating PASID-capable domains to more drivers
   - Remove iommu_present()
   - Some smaller improvements

  New IOMMU driver for RISC-V

  Intel VT-d Updates:
   - Add domain_alloc_paging support
   - Enable user space IOPFs in non-PASID and non-svm cases
   - Small code refactoring and cleanups
   - Add domain replacement support for pasid

  AMD-Vi Updates:
   - Adapt to iommu_paging_domain_alloc_flags() interface and alloc V2
     page-tables by default
   - Replace custom domain ID allocator with IDA allocator
   - Add ops->release_domain() support
   - Other improvements to device attach and domain allocation code
     paths

  ARM-SMMU Updates:
   - SMMUv2:
      - Return -EPROBE_DEFER for client devices probing before their
        SMMU
      - Devicetree binding updates for Qualcomm MMU-500 implementations
   - SMMUv3:
      - Minor fixes and cleanup for NVIDIA's virtual command queue
        driver
   - IO-PGTable:
      - Fix indexing of concatenated PGDs and extend selftest coverage
      - Remove unused block-splitting support

  S390 IOMMU:
   - Implement support for blocking domain

  Mediatek IOMMU:
   - Enable 35-bit physical address support for mt8186

  OMAP IOMMU driver:
   - Adapt to recent IOMMU core changes and unbreak driver"

* tag 'iommu-updates-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (92 commits)
  iommu/tegra241-cmdqv: Fix alignment failure at max_n_shift
  iommu: Make set_dev_pasid op support domain replacement
  iommu/arm-smmu-v3: Make set_dev_pasid() op support replace
  iommu/vt-d: Add set_dev_pasid callback for nested domain
  iommu/vt-d: Make identity_domain_set_dev_pasid() to handle domain replacement
  iommu/vt-d: Make intel_svm_set_dev_pasid() support domain replacement
  iommu/vt-d: Limit intel_iommu_set_dev_pasid() for paging domain
  iommu/vt-d: Make intel_iommu_set_dev_pasid() to handle domain replacement
  iommu/vt-d: Add iommu_domain_did() to get did
  iommu/vt-d: Consolidate the struct dev_pasid_info add/remove
  iommu/vt-d: Add pasid replace helpers
  iommu/vt-d: Refactor the pasid setup helpers
  iommu/vt-d: Add a helper to flush cache for updating present pasid entry
  iommu: Pass old domain to set_dev_pasid op
  iommu/iova: Fix typo 'adderss'
  iommu: Add a kdoc to iommu_unmap()
  iommu/io-pgtable-arm-v7s: Remove split on unmap behavior
  iommu/io-pgtable-arm: Remove split on unmap behavior
  iommu/vt-d: Drain PRQs when domain removed from RID
  iommu/vt-d: Drop pasid requirement for prq initialization
  ...

3 months agoMerge tag 'thermal-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafae...
Linus Torvalds [Sat, 23 Nov 2024 03:43:18 +0000 (19:43 -0800)]
Merge tag 'thermal-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull more thermal control updates from Rafael Wysocki:
 "These update a few thermal drivers used on ARM platforms and thermal
  tools:

   - Add SAR2130P compatible to DT bindings in the QCom Tsens driver
     (Dmitry Baryshkov)

   - Add static annotation to arrays describing platform sensors in the
     LVTS Mediatek driver (Colin Ian King)

   - Switch back to struct platform_driver::remove() from the previous
     callbacks prototype rework (Uwe Kleine-König)

   - Add MSM8937 compatible to DT bindings and its support in the QCom
     Tsens driver (Barnabás Czémán)

   - Remove a pointless sign test on an unsigned value in
     k3_bgp_read_temp() in the k3_j72xx_bandgap driver (Rex Nie)

   - Fix a pointer reference loss when realloc() fails in the thermal
     library (Zhang Jiao)"

* tag 'thermal-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  tools/thermal: Fix common realloc mistake
  thermal/drivers/k3_j72xx_bandgap: Simplify code in k3_bgp_read_temp()
  thermal/drivers/qcom/tsens-v1: Add support for MSM8937 tsens
  dt-bindings: thermal: tsens: Add MSM8937
  thermal: Switch back to struct platform_driver::remove()
  thermal/drivers/mediatek/lvts_thermal: Make read-only arrays static const
  dt-bindings: thermal: qcom-tsens: Add SAR2130P compatible

3 months agoMerge tag 'pm-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael...
Linus Torvalds [Sat, 23 Nov 2024 03:29:48 +0000 (19:29 -0800)]
Merge tag 'pm-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull more power management updates from Rafael Wysocki:
 "These mostly are updates of cpufreq drivers used on ARM platforms plus
  one new DT-based cpufreq driver for virtualized guests and two cpuidle
  changes that should not make any difference on systems currently in
  the field, but will be needed for future development:

   - Add virtual cpufreq driver for guest kernels (David Dai)

   - Minor cleanup to various cpufreq drivers (Andy Shevchenko, Dhruva
     Gole, Jie Zhan, Jinjie Ruan, Shuosheng Huang, Sibi Sankar, and Yuan
     Can)

   - Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check"
     (Colin Ian King)

   - Improve DT bindings for qcom-hw driver (Dmitry Baryshkov, Konrad
     Dybcio, and Nikunj Kela)

   - Make cpuidle_play_dead() try all idle states with :enter_dead()
     callbacks and change their return type to void (Rafael Wysocki)"

* tag 'pm-6.13-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
  cpuidle: Change :enter_dead() driver callback return type to void
  cpuidle: Do not return from cpuidle_play_dead() on callback failures
  arm64: dts: qcom: sc8180x: Add a SoC-specific compatible to cpufreq-hw
  dt-bindings: cpufreq: cpufreq-qcom-hw: Add SC8180X compatible
  cpufreq: sun50i: add a100 cpufreq support
  cpufreq: mediatek-hw: Fix wrong return value in mtk_cpufreq_get_cpu_power()
  cpufreq: CPPC: Fix wrong return value in cppc_get_cpu_power()
  cpufreq: CPPC: Fix wrong return value in cppc_get_cpu_cost()
  cpufreq: loongson3: Check for error code from devm_mutex_init() call
  cpufreq: scmi: Fix cleanup path when boost enablement fails
  cpufreq: CPPC: Fix possible null-ptr-deref for cppc_get_cpu_cost()
  cpufreq: CPPC: Fix possible null-ptr-deref for cpufreq_cpu_get_raw()
  Revert "cpufreq: brcmstb-avs-cpufreq: Fix initial command check"
  dt-bindings: cpufreq: cpufreq-qcom-hw: Add SAR2130P compatible
  cpufreq: add virtual-cpufreq driver
  dt-bindings: cpufreq: add virtual cpufreq device
  cpufreq: loongson2: Unregister platform_driver on failure
  cpufreq: ti-cpufreq: Remove revision offsets in AM62 family
  cpufreq: ti-cpufreq: Allow backward compatibility for efuse syscon
  cppc_cpufreq: Remove HiSilicon CPPC workaround
  ...

3 months agoMerge tag 'tpmdd-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 23 Nov 2024 01:25:32 +0000 (17:25 -0800)]
Merge tag 'tpmdd-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd

Pull TPM updates from Jarkko Sakkinen:
 "Only some minor tweaks"

* tag 'tpmdd-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
  tpm: atmel: Drop PPC64 specific MMIO setup
  char: tpm: cr50: Add new device/vendor ID 0x50666666
  char: tpm: cr50: Move i2c locking to request/relinquish locality ops
  char: tpm: cr50: Use generic request/relinquish locality ops
  tpm: ibmvtpm: Set TPM_OPS_AUTO_STARTUP flag on driver

3 months agoMerge tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Linus Torvalds [Sat, 23 Nov 2024 01:06:59 +0000 (17:06 -0800)]
Merge tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Miquel Raynal:
 "MTD device changes:
   - switch platform_driver back to remove()
   - misc fixes

  SPI-NAND changes:
   - a load of fixes to Winbond manufacturer driver
   - structure constification

  Raw NAND changes:
   - improve the power management of the GPMI driver
   - Davinci driver clean-ups
   - fix leak in the Atmel driver
   - fix some typos in the core

  SPI NOR changes:
   - Introduce byte swap support for 8D-8D-8D mode and a user for it:
     macronix.

     SPI NOR flashes may swap the bytes on a 16-bit boundary when
     configured in Octal DTR mode. For such cases the byte order is
     propagated through SPI MEM to the SPI controllers so that the
     controllers swap the bytes back at runtime. This avoids breaking
     the boot sequence because of the endianness problems that appear
     when the bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with
     byte swap support. Along with the SPI MEM byte swap support we
     queue a patch for the SPI MXIC controller that swaps the bytes back
     at runtime"

* tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (25 commits)
  mtd: spi-nor: core: replace dummy buswidth from addr to data
  mtd: spi-nor: winbond: add "w/ and w/o SFDP" comment
  mtd: spi-nor: spansion: Use nor->addr_nbytes in octal DTR mode in RD_ANY_REG_OP
  mtd: Switch back to struct platform_driver::remove()
  mtd: cfi_cmdset_0002: remove redundant assignment to variable ret
  mtd: spinand: Constify struct nand_ecc_engine_ops
  MAINTAINERS: add mailing list for GPMI NAND driver
  mtd: spinand: winbond: Sort the devices
  mtd: spinand: winbond: Ignore the last ID characters
  mtd: spinand: winbond: Fix 512GW, 01GW, 01JW and 02JW ECC information
  mtd: spinand: winbond: Fix 512GW and 02JW OOB layout
  mtd: nand: raw: gpmi: improve power management handling
  mtd: nand: raw: gpmi: switch to SYSTEM_SLEEP_PM_OPS
  mtd: rawnand: davinci: use generic device property helpers
  mtd: rawnand: davinci: break the line correctly
  mtd: rawnand: davinci: order headers alphabetically
  mtd: rawnand: atmel: Fix possible memory leak
  mtd: rawnand: Correct multiple typos in comments
  mtd: hyperbus: rpc-if: Add missing MODULE_DEVICE_TABLE
  mtd: spi-nor: add support for Macronix Octal flash
  ...

3 months agoMerge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Linus Torvalds [Sat, 23 Nov 2024 01:02:25 +0000 (17:02 -0800)]
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
 "The core framework gained a clk provider helper, a clk consumer
  helper, and some unit tests for the assigned clk rates feature in
  DeviceTree. On the vendor driver side, we gained a whole pile of SoC
  driver support detailed below. The majority in the diffstat is
  Qualcomm, but there's also quite a few Samsung and Mediatek clk driver
  additions in here as well. The top vendors is quite common, but the
  sheer amount of new drivers is uncommon, so I'm anticipating a larger
  number of fixes for clk drivers this cycle.

  Core:
   - devm_clk_bulk_get_all_enabled() to return number of clks acquired
   - devm_clk_hw_register_gate_parent_hw() helper to modernize drivers
   - KUnit tests for clk-assigned-rates{,-u64}

  New Drivers:
   - Marvell PXA1908 SoC clks
   - Mobileye EyeQ5, EyeQ6L and EyeQ6H clk driver
   - TWL6030 clk driver
   - Nuvoton Arbel BMC NPCM8XX SoC clks
   - MediaTek MT6735 SoC clks
   - MediaTek MT7620, MT7628 and MT7688 MMC clks
   - Add a driver for gated fixed rate clocks
   - Global clock controllers for Qualcomm QCS8300 and IPQ5424 SoCs
   - Camera, display and video clock controllers for Qualcomm SA8775P
     SoCs
   - Global, display, GPU, TCSR, and RPMh clock controllers for Qualcomm
     SAR2130P
   - Global, camera, display, GPU, and video clock controllers for
     Qualcomm SM8475 SoCs
   - RTC power domain and Battery Backup Function (VBATTB) clock support
     for the Renesas RZ/G3S SoC
   - Qualcomm IPQ9574 alpha PLLs
   - Support for i.MX91 CCM in the i.MX93 driver
   - Microchip LAN969X SoC clks
   - Cortex-A55 core clocks and Interrupt Control Unit (ICU) clock and
     reset on Renesas RZ/V2H(P)
   - Samsung ExynosAutov920 clk drivers for PERIC1, MISC, HSI0 and HSI1
   - Samsung Exynos8895 clk drivers for FSYS0/1, PERIC0/1, PERIS and TOP

  Updates:
   - Convert more clk bindings to YAML
   - Various clk driver cleanups: NULL checks, add const, etc.
   - Remove END/NUM #defines that count number of clks in various
     binding headers
   - Continue moving reset drivers to drivers/reset via auxiliary bus"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
  clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access
  clk: Fix invalid execution of clk_set_rate
  clk: clk-loongson2: Fix memory corruption bug in struct loongson2_clk_provider
  clk: lan966x: make it selectable for ARCH_LAN969X
  clk: eyeq: add EyeQ6H west fixed factor clocks
  clk: eyeq: add EyeQ6H central fixed factor clocks
  clk: eyeq: add EyeQ5 fixed factor clocks
  clk: eyeq: add fixed factor clocks infrastructure
  clk: eyeq: require clock index with phandle in all cases
  clk: fixed-factor: add clk_hw_register_fixed_factor_index() function
  dt-bindings: clock: eyeq: add more Mobileye EyeQ5/EyeQ6H clocks
  dt-bindings: soc: mobileye: set `#clock-cells = <1>` for all compatibles
  clk: clk-axi-clkgen: make sure to enable the AXI bus clock
  dt-bindings: clock: axi-clkgen: include AXI clk
  clk: mmp: Add Marvell PXA1908 MPMU driver
  clk: mmp: Add Marvell PXA1908 APMU driver
  clk: mmp: Add Marvell PXA1908 APBCP driver
  clk: mmp: Add Marvell PXA1908 APBC driver
  dt-bindings: clock: Add Marvell PXA1908 clock bindings
  clk: mmp: Switch to use struct u32_fract instead of custom one
  ...

3 months agoMerge tag 'backlight-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 23 Nov 2024 00:29:57 +0000 (16:29 -0800)]
Merge tag 'backlight-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight

Pull backlight updates from Lee Jones:

 - Improve handling of LCD power states and interactions with the fbdev
   subsystem

 - Introduce new LCD_POWER_ constants to decouple the LCD subsystem from
   fbdev

 - Update several drivers to use the new LCD_POWER_ constants

 - Clarify the semantics of the lcd_ops.controls_device callback

 - Remove unnecessary includes and dependencies

 - Remove unused notifier functionality

 - Simplify code with scoped for-each loops

 - Fix module autoloading for the ktz8866 driver

 - Update device tree bindings to yaml format

 - Minor cleanups and improvements in various drivers

* tag 'backlight-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: (33 commits)
  MAINTAINERS: Use Daniel Thompson's korg address for Backlight work
  dt-bindings: backlight: Convert zii,rave-sp-backlight.txt to yaml
  backlight: Remove notifier
  backlight: ktz8866: Fix module autoloading
  backlight: 88pm860x_bl: Simplify with scoped for each OF child loop
  backlight: lcd: Do not include <linux/fb.h> in lcd header
  backlight: lcd: Remove struct fb_videomode from set_mode callback
  backlight: lcd: Replace check_fb with controls_device
  HID: picoLCD: Replace check_fb in favor of struct fb_info.lcd_dev
  fbdev: omap: Use lcd power constants
  fbdev: imxfb: Use lcd power constants
  fbdev: imxfb: Replace check_fb in favor of struct fb_info.lcd_dev
  fbdev: clps711x-fb: Use lcd power constants
  fbdev: clps711x-fb: Replace check_fb in favor of struct fb_info.lcd_dev
  backlight: tdo24m: Use lcd power constants
  backlight: platform_lcd: Use lcd power constants
  backlight: platform_lcd: Remove match_fb from struct plat_lcd_data
  backlight: platform_lcd: Remove include statement for <linux/backlight.h>
  backlight: otm3225a: Use lcd power constants
  backlight: ltv350qv: Use lcd power constants
  ...

3 months agoMerge tag 'leds-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Linus Torvalds [Sat, 23 Nov 2024 00:25:20 +0000 (16:25 -0800)]
Merge tag 'leds-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds

PULL LED updates from Lee Jones:

 - Remove unused local header files from various drivers

 - Revert platform driver removal to the original method for consistency

 - Introduce ordered workqueues for LED events, replacing the less
   efficient system_wq

 - Switch to a safer iteration macro in several drivers to prevent
   potential memory leaks

 - Fix a refcounting bug in the mt6360 flash LED driver

 - Fix an uninitialized variable in the mt6370_mc_pattern_clear()
   function

 - Resolve Smatch warnings in the leds-bcm6328 driver

 - Address a potential NULL pointer dereference in the brightness_show()
   function

 - Fix an incorrect format specifier in the ss4200 driver

 - Prevent a resource leak in the max5970 driver's probe function

 - Add support for specifying the number of serial shift bits in the
   device tree for the BCM63138 family

 - Implement multicolor brightness control in the lp5562 driver

 - Add a device tree property to override the default LED pin polarity

 - Add a property to specify the default brightness value when the LED
   is initially on

 - Set missing timing properties for the ktd2692 driver

 - Document the "rc-feedback" trigger for controlling LEDs based on
   remote control activity

 - Convert text bindings to YAML for the pca955x driver to enable device
   tree validation

 - Remove redundant checks for invalid channel numbers in the lp55xx
   driver

 - Update the MAINTAINERS file with current contact information

* tag 'leds-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (46 commits)
  leds: ss4200: Fix the wrong format specifier for 'blinking'
  leds: pwm: Add optional DT property default-brightness
  dt-bindings: leds: pwm: Add default-brightness property
  leds: class: Protect brightness_show() with led_cdev->led_access mutex
  leds: ktd2692: Set missing timing properties
  leds: max5970: Fix unreleased fwnode_handle in probe function
  leds: Introduce ordered workqueue for LEDs events instead of system_wq
  MAINTAINERS: Replace Siemens IPC related bouncing maintainers
  leds: bcm6328: Replace divide condition with comparison for shift value
  leds: lp55xx: Remove redundant test for invalid channel number
  dt-bindings: leds: pca955x: Convert text bindings to YAML
  leds: rgb: leds-mt6370-rgb: Fix uninitialized variable 'ret' in mt6370_mc_pattern_clear
  leds: lp5562: Add multicolor brightness control
  dt-bindings: leds: Add 'active-high' property
  leds: Switch back to struct platform_driver::remove()
  leds: bcm63138: Add some register defines
  leds: bcm63138: Handle shift register config
  leds: bcm63138: Use scopes and guards
  dt-bindings: leds: bcm63138: Add shift register bits
  leds: leds-gpio-register: Reorganize kerneldoc parameter names
  ...

3 months agoMerge tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Linus Torvalds [Sat, 23 Nov 2024 00:19:47 +0000 (16:19 -0800)]
Merge tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:

 - Several drivers, including atmel-flexcom/rk8xx-core, palmas, and
   tps65010, have undergone minor code improvements to enhance
   consistency and fix race conditions.

 - The syscon driver now utilizes the regmap max_register_is_0
   capability for consistent register map configuration across syscons
   of all sizes.

 - New device support has been added for QCS8300, qcs615, SA8255p, and
   samsung,s2dos05, expanding the range of compatible hardware.

 - The cros_ec driver now supports loading cros_ec_ucsi on supported ECs
   and avoids loading the charger with UCSI, streamlining functionality.

 - The bd96801 driver now utilizes the more modern maple tree register
   cache, improving performance.

 - The da9052-spi driver has undergone a fix to change the read-mask to
   write-mask, preventing potential issues.

 - Unused declarations in max77693 have been removed, and support for
   samsung,s2dos05 has been added, enhancing code clarity and device
   compatibility.

 - Error handling in cs42l43 has been fixed to avoid unbalanced
   regulator put and ensure proper synchronization during driver
   removal.

 - The wcd934x driver now uses MODULE_DEVICE_TABLE() instead of
   MODULE_ALIAS(), improving code consistency.

 - Documentation for qcom,tcsr, syscon, and atmel-smc has been updated
   and reorganized for better clarity and maintainability.

 - The intel_soc_pmic_bxtwc driver has undergone significant
   improvements, including the use of IRQ domains for various devices,
   fixing IRQ domain names duplication, and code refactoring for better
   consistency and maintainability.

 - The ipaq-micro driver has received a fix for a missing break
   statement in the default case, enhancing code robustness.

 - Support for the AXP323 PMIC has been added to the axp20x driver,
   along with ensuring a clear relationship between IDs and model names,
   and allowing multiple regulators, broadening hardware compatibility.

 - The cs42l43 driver now disables IRQs during suspend for improved
   power management.

 - The adp5585 driver has reduced its dependencies by dropping the
   obsolete dependency on COMPILE_TEST.

 - Initial support for the MT6328 PMIC has been added to the mt6397
   driver, expanding the range of supported hardware.

 - The rtc-bd70528 driver has been simplified by dropping the IC name
   from IRQ, improving code readability.

 - Documentation for qcom,spmi-pmic, ti,twl, and zii,rave-sp has been
   updated to enhance clarity and incorporate new features.

 - The rt5033 driver has received a fix for a missing
   regmap_del_irq_chip() in the error handling path.

 - New device support has been added for MSM8917, and the
   intel_soc_pmic_crc driver now supports non-ACPI instantiated
   i2c_client.

 - The 88pm886 driver has added support for the RTC cell, and the tqmx86
   driver has improved its GPIO IRQ setup and added I2C IRQ support,
   increasing functionality.

 - The sprd,sc2731 DT schema has been updated and converted to YAML
   format for better readability and maintainability.

* tag 'mfd-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (62 commits)
  dt-bindings: mfd: bd71828: Use charger resistor in mOhm instead of MOhm
  dt-bindings: mfd: sprd,sc2731: Convert to YAML
  mfd: tqmx86: Add I2C IRQ support
  mfd: tqmx86: Make IRQ setup errors non-fatal
  mfd: tqmx86: Refactor GPIO IRQ setup
  mfd: tqmx86: Improve gpio_irq module parameter description
  mfd: tqmx86: Add board definitions for TQMx120UC, TQMx130UC and TQMxE41S
  mfd: 88pm886: Add the RTC cell
  dt-bindings: mfd: Add Realtek RTL9300 switch peripherals
  mfd: intel_soc_pmic_crc: Add support for non ACPI instantiated i2c_client
  mfd: intel_soc_pmic_*: Consistently use filename as driver name
  dt-bindings: mfd: qcom,tcsr: Add compatible for MSM8917
  mfd: rt5033: Fix missing regmap_del_irq_chip()
  mfd: cgbc-core: Fix error handling paths in cgbc_init_device()
  dt-bindings: mfd: aspeed: Support for AST2700
  mfd: Switch back to struct platform_driver::remove()
  dt-bindings: mfd: qcom,spmi-pmic: Document PMICs added in SM8750
  mfd: rtc: bd7xxxx Drop IC name from IRQ
  mfd: mt6397: Add initial support for MT6328
  mfd: adp5585: Drop obsolete dependency on COMPILE_TEST
  ...

3 months agoMerge tag 'linux_kselftest-kunit-6.13-rc1-fixed' of git://git.kernel.org/pub/scm...
Linus Torvalds [Sat, 23 Nov 2024 00:11:56 +0000 (16:11 -0800)]
Merge tag 'linux_kselftest-kunit-6.13-rc1-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kunit updates from Shuah Khan:

 - fix user-after-free (UAF) bug in kunit_init_suite()

 - add option to kunit tool to print just the summary of test results

 - add option to kunit tool to print just the failed test results

 - fix kunit_zalloc_skb() to use user passed in gfp value instead of
   hardcoding GFP_KERNEL

 - fixe kunit_zalloc_skb() kernel doc to include allocation flags
   variable

 - update KUnit email address for Brendan Higgins

 - add LoongArch config to qemu_configs

 - allow overriding the shutdown mode from qemu config

 - enable shutdown in loongarch qemu_config

 - fix potential null dereference in kunit_device_driver_test()

 - fix debugfs to use IS_ERR() for alloc_string_stream() error check

* tag 'linux_kselftest-kunit-6.13-rc1-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  kunit: qemu_configs: loongarch: Enable shutdown
  kunit: tool: Allow overriding the shutdown mode from qemu config
  kunit: qemu_configs: Add LoongArch config
  kunit: debugfs: Use IS_ERR() for alloc_string_stream() error check
  kunit: Fix potential null dereference in kunit_device_driver_test()
  MAINTAINERS: Update KUnit email address for Brendan Higgins
  kunit: string-stream: Fix a UAF bug in kunit_init_suite()
  kunit: tool: print failed tests only
  kunit: tool: Only print the summary
  kunit: skb: add gfp to kernel doc for kunit_zalloc_skb()
  kunit: skb: use "gfp" variable instead of hardcoding GFP_KERNEL

3 months agoMerge tag 'trace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux...
Linus Torvalds [Fri, 22 Nov 2024 21:27:01 +0000 (13:27 -0800)]
Merge tag 'trace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull tracing updates from Steven Rostedt:

 - Addition of faultable tracepoints

   There's a tracepoint attached to both a system call entry and exit.
   This location is known to allow page faults. The tracepoints are
   called under an rcu_read_lock() which does not allow faults that can
   sleep. This limits the ability of tracepoint handlers to page fault
   in user space system call parameters. Now these tracepoints have been
   made "faultable", allowing the callbacks to fault in user space
   parameters and record them.

   Note, only the infrastructure has been implemented. The consumers
   (perf, ftrace, BPF) now need to have their code modified to allow
   faults.

 - Fix up of BPF code for the tracepoint faultable logic

 - Update tracepoints to use the new static branch API

 - Remove trace_*_rcuidle() variants and the SRCU protection they used

 - Remove unused TRACE_EVENT_FL_FILTERED logic

 - Replace strncpy() with strscpy() and memcpy()

 - Use replace per_cpu_ptr(smp_processor_id()) with this_cpu_ptr()

 - Fix perf events to not duplicate samples when tracing is enabled

 - Replace atomic64_add_return(1, counter) with
   atomic64_inc_return(counter)

 - Make stack trace buffer 4K instead of PAGE_SIZE

 - Remove TRACE_FLAG_IRQS_NOSUPPORT flag as it was never used

 - Get the true return address for function tracer when function graph
   tracer is also running.

   When function_graph trace is running along with function tracer, the
   parent function of the function tracer sometimes is
   "return_to_handler", which is the function graph trampoline to record
   the exit of the function. Use existing logic that calls into the
   fgraph infrastructure to find the real return address.

 - Remove (un)regfunc pointers out of tracepoint structure

 - Added last minute bug fix for setting pending modules in stack
   function filter.

     echo "write*:mod:ext3" > /sys/kernel/tracing/stack_trace_filter

   Would cause a kernel NULL dereference.

 - Minor clean ups

* tag 'trace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (31 commits)
  ftrace: Fix regression with module command in stack_trace_filter
  tracing: Fix function name for trampoline
  ftrace: Get the true parent ip for function tracer
  tracing: Remove redundant check on field->field in histograms
  bpf: ensure RCU Tasks Trace GP for sleepable raw tracepoint BPF links
  bpf: decouple BPF link/attach hook and BPF program sleepable semantics
  bpf: put bpf_link's program when link is safe to be deallocated
  tracing: Replace strncpy() with strscpy() when copying comm
  tracing: Add might_fault() check in __DECLARE_TRACE_SYSCALL
  tracing: Fix syscall tracepoint use-after-free
  tracing: Introduce tracepoint_is_faultable()
  tracing: Introduce tracepoint extended structure
  tracing: Remove TRACE_FLAG_IRQS_NOSUPPORT
  tracing: Replace multiple deprecated strncpy with memcpy
  tracing: Make percpu stack trace buffer invariant to PAGE_SIZE
  tracing: Use atomic64_inc_return() in trace_clock_counter()
  trace/trace_event_perf: remove duplicate samples on the first tracepoint event
  tracing/bpf: Add might_fault check to syscall probes
  tracing/perf: Add might_fault check to syscall probes
  tracing/ftrace: Add might_fault check to syscall probes
  ...

3 months agoMerge tag 'trace-tools-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace...
Linus Torvalds [Fri, 22 Nov 2024 21:24:22 +0000 (13:24 -0800)]
Merge tag 'trace-tools-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull tracing tools updates from Steven Rostedt:

 - Add ':' to getopt option 'trace-buffer-size' in timerlat_hist for
   consistency

 - Remove unused sched_getattr define

 - Rename sched_setattr() helper to syscall_sched_setattr() to avoid
   conflicts

 - Update counters to long from int to avoid overflow

 - Add libcpupower dependency detection

 - Add --deepest-idle-state to timerlat to limit deep idle sleeps

 - Other minor clean ups and documentation changes

* tag 'trace-tools-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  verification/dot2: Improve dot parser robustness
  tools/rtla: Improve exception handling in timerlat_load.py
  tools/rtla: Enhance argument parsing in timerlat_load.py
  tools/rtla: Improve code readability in timerlat_load.py
  rtla/timerlat: Do not set params->user_workload with -U
  rtla: Documentation: Mention --deepest-idle-state
  rtla/timerlat: Add --deepest-idle-state for hist
  rtla/timerlat: Add --deepest-idle-state for top
  rtla/utils: Add idle state disabling via libcpupower
  rtla: Add optional dependency on libcpupower
  tools/build: Add libcpupower dependency detection
  rtla/timerlat: Make timerlat_hist_cpu->*_count unsigned long long
  rtla/timerlat: Make timerlat_top_cpu->*_count unsigned long long
  tools/rtla: fix collision with glibc sched_attr/sched_set_attr
  tools/rtla: drop __NR_sched_getattr
  rtla: Fix consistency in getopt_long for timerlat_hist
  rv: Fix a typo
  tools/rv: Correct the grammatical errors in the comments
  tools/rv: Correct the grammatical errors in the comments
  rtla: use the definition for stdout fd when calling isatty()

3 months agoMerge tag 'trace-ring-buffer-v6.13' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Fri, 22 Nov 2024 21:11:17 +0000 (13:11 -0800)]
Merge tag 'trace-ring-buffer-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull trace ring-buffer updates from Steven Rostedt:

 - Limit time interrupts are disabled in rb_check_pages()

   rb_check_pages() is called after the ring buffer size is updated to
   make sure that the ring buffer has not been corrupted. Commit
   c2274b908db0 ("ring-buffer: Fix a race between readers and resize
   checks") fixed a race with the check pages and simultaneous resizes
   to the ring buffer by adding a raw_spin_lock_irqsave() around the
   check operation. Although this was a simple fix, it would hold
   interrupts disabled for non determinative amount of time. This could
   harm PREEMPT_RT operations.

   Instead, modify the logic by adding a counter when the buffer is
   modified and to release the raw_spin_lock() at each iteration. It
   checks the counter under the lock to see if a modification happened
   during the loop, and if it did, it would restart the loop up to 3
   times. After 3 times, it will simply exit the check, as it is
   unlikely that would ever happen as buffer resizes are rare
   occurrences.

 - Replace some open coded str_low_high() with the helper

 - Fix some documentation/comments

* tag 'trace-ring-buffer-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  ring-buffer: Correct a grammatical error in a comment
  ring-buffer: Use str_low_high() helper in ring_buffer_producer()
  ring-buffer: Reorganize kerneldoc parameter names
  ring-buffer: Limit time with disabled interrupts in rb_check_pages()

3 months agoMerge tag 'x86_tdx_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 22 Nov 2024 21:07:19 +0000 (13:07 -0800)]
Merge tag 'x86_tdx_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull tdx updates from Dave Hansen:
 "These essentially refine some interactions between TDX guests and
  VMMs.

  The first leverages a new TDX module feature to runtime disable the
  ability for a VM to inject #VE exceptions. Before this feature, there
  was only a static on/off switch and the guest had to panic if it was
  configured in a bad state.

  The second lets the guest opt in to be able to access the topology
  CPUID leaves. Before this, accesses to those leaves would #VE.

  For both of these, it would have been nicest to just change the
  default behavior, but some pesky "other" OSes evidently need to retain
  the legacy behavior.

  Summary:

   - Add new infrastructure for reading TDX metadata

   - Use the newly-available metadata to:
      - Disable potentially nasty #VE exceptions
      - Get more complete CPU topology information from the VMM"

* tag 'x86_tdx_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tdx: Enable CPU topology enumeration
  x86/tdx: Dynamically disable SEPT violations from causing #VEs
  x86/tdx: Rename tdx_parse_tdinfo() to tdx_setup()
  x86/tdx: Introduce wrappers to read and write TD metadata

3 months agoMerge tag 'x86_misc_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 22 Nov 2024 20:52:03 +0000 (12:52 -0800)]
Merge tag 'x86_misc_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull misc x86 updates from Dave Hansen:
 "As usual for this branch, these are super random: a compile fix for
  some newish LLVM checks and making sure a Kconfig text reference to
  'RSB' matches the normal definition:

   - Rework some CPU setup code to keep LLVM happy on 32-bit

   - Correct RSB terminology in Kconfig text"

* tag 'x86_misc_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Make sure flag_is_changeable_p() is always being used
  x86/bugs: Correct RSB terminology in Kconfig

3 months agoMerge tag 'x86_sgx_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Fri, 22 Nov 2024 20:50:00 +0000 (12:50 -0800)]
Merge tag 'x86_sgx_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull sgx update from Dave Hansen:

 - Use vmalloc_array() instead of vmalloc()

* tag 'x86_sgx_for_6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sgx: Use vmalloc_array() instead of vmalloc()

3 months agoMerge tag 'cxl-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Linus Torvalds [Fri, 22 Nov 2024 20:33:52 +0000 (12:33 -0800)]
Merge tag 'cxl-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl

Pull cxl updates from Dave Jiang:

 - Constify range_contains() input parameters to prevent changes

 - Add support for displaying RCD capabilities in sysfs to support lspci
   for CXL device

 - Downgrade warning message to debug in cxl_probe_component_regs()

 - Add support for adding a printf specifier '%pra' to emit 'struct
   range' content:
     - Add sanity tests for 'struct resource'
     - Add documentation for special case
     - Add %pra for 'struct range'
     - Add %pra usage in CXL code

 - Add preparation code for DCD support:
     - Add range_overlaps()
     - Add CDAT DSMAS table shared and read only flag in ACPICA
     - Add documentation to 'struct dev_dax_range'
     - Delay event buffer allocation in CXL PCI code until needed
     - Use guard() in cxl_dpa_set_mode()
     - Refactor create region code to consolidate common code

* tag 'cxl-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/region: Refactor common create region code
  cxl/hdm: Use guard() in cxl_dpa_set_mode()
  cxl/pci: Delay event buffer allocation
  dax: Document struct dev_dax_range
  ACPI/CDAT: Add CDAT/DSMAS shared and read only flag values
  range: Add range_overlaps()
  cxl/cdat: Use %pra for dpa range outputs
  printf: Add print format (%pra) for struct range
  Documentation/printf: struct resource add start == end special case
  test printf: Add very basic struct resource tests
  cxl: downgrade a warning message to debug level in cxl_probe_component_regs()
  cxl/pci: Add sysfs attribute for CXL 1.1 device link status
  cxl/core/regs: Add rcd_pcie_cap initialization
  kernel/range: Const-ify range_contains parameters

3 months agoMerge branch 'pm-cpuidle'
Rafael J. Wysocki [Fri, 22 Nov 2024 20:17:18 +0000 (21:17 +0100)]
Merge branch 'pm-cpuidle'

Merge additional cpuidle changes for 6.13-rc1:

 - Make cpuidle_play_dead() try all idle states with :enter_dead()
   callbacks and change their return type to void (Rafael Wysocki).

* pm-cpuidle:
  cpuidle: Change :enter_dead() driver callback return type to void
  cpuidle: Do not return from cpuidle_play_dead() on callback failures

3 months agotpm: atmel: Drop PPC64 specific MMIO setup
Rob Herring (Arm) [Wed, 6 Nov 2024 18:17:42 +0000 (20:17 +0200)]
tpm: atmel: Drop PPC64 specific MMIO setup

The PPC64 specific MMIO setup open codes DT address functions rather
than using standard address parsing functions. The open-coded version
fails to handle any address translation and is not endian safe.

I haven't found any evidence of what platform used this. The only thing
that turned up was a PPC405 platform, but that is 32-bit and PPC405
support is being removed as well. CONFIG_TCG_ATMEL is not enabled for
any powerpc config and never was. The support was added in 2005 and
hasn't been touched since.

Rather than try to modernize and fix this code, just remove it.

[jarkko: fixed couple of style issues reported by checkpatch.pl --strict
 and put offset into parentheses in the macro declarations.]
Signed-off-by: Rob Herring (Arm) <[email protected]>
Acked-by: Michael Ellerman <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
3 months agoMerge tag 'drm-next-2024-11-21' of https://gitlab.freedesktop.org/drm/kernel
Linus Torvalds [Thu, 21 Nov 2024 22:56:17 +0000 (14:56 -0800)]
Merge tag 'drm-next-2024-11-21' of https://gitlab.freedesktop.org/drm/kernel

Pull drm updates from Dave Airlie:
 "There's a lot of rework, the panic helper support is being added to
  more drivers, v3d gets support for HW superpages, scheduler
  documentation, drm client and video aperture reworks, some new
  MAINTAINERS added, amdgpu has the usual lots of IP refactors, Intel
  has some Pantherlake enablement and xe is getting some SRIOV bits, but
  just lots of stuff everywhere.

  core:
   - split DSC helpers from DP helpers
   - clang build fixes for drm/mm test
   - drop simple pipeline support for gem vram
   - document submission error signaling
   - move drm_rect to drm core module from kms helper
   - add default client setup to most drivers
   - move to video aperture helpers instead of drm ones

  tests:
   - new framebuffer tests

  ttm:
   - remove swapped and pinned BOs from TTM lru

  panic:
   - fix uninit spinlock
   - add ABGR2101010 support

  bridge:
   - add TI TDP158 support
   - use standard PM OPS

  dma-fence:
   - use read_trylock instead of read_lock to help lockdep

  scheduler:
   - add errno to sched start to report different errors
   - add locking to drm_sched_entity_modify_sched
   - improve documentation

  xe:
   - add drm_line_printer
   - lots of refactoring
   - Enable Xe2 + PES disaggregation
   - add new ARL PCI ID
   - SRIOV development work
   - fix exec unnecessary implicit fence
   - define and parse OA sync props
   - forcewake refactoring

  i915:
   - Enable BMG/LNL ultra joiner
   - Enable 10bpx + CCS scanout on ICL+, fp16/CCS on TGL+
   - use DSB for plane/color mgmt
   - Arrow lake PCI IDs
   - lots of i915/xe display refactoring
   - enable PXP GuC autoteardown
   - Pantherlake (PTL) Xe3 LPD display enablement
   - Allow fastset HDR infoframe changes
   - write DP source OUI for non-eDP sinks
   - share PCI IDs between i915 and xe

  amdgpu:
   - SDMA queue reset support
   - SMU 13.0.6, JPEG 4.0.3 updates
   - Initial runtime repartitioning support
   - rework IP structs for multiple IP instances
   - Fetch EDID from _DDC if available
   - SMU13 zero rpm user control
   - lots of fixes/cleanups

  amdkfd:
   - Increase event FIFO size
   - add topology cap flag for per queue reset

  msm:
   - DPU:
      - SA8775P support
      - (disabled by default) MSM8917, MSM8937, MSM8953 and MSM8996 support
      - Enable large framebuffer support
      - Drop MSM8998 and SDM845
   - DP:
      - SA8775P support
   - GPU:
      - a7xx preemption support
      - Adreno A663 support

  ast:
   - warn about unsupported TX chips

  ivpu:
   - add coredump
   - add pantherlake support

  rockchip:
   - 4K@60Hz display enablement
   - generate pll programming tables

  panthor:
   - add timestamp query API
   - add realtime group priority
   - add fdinfo support

  etnaviv:
   - improve handling of DMA address limits
   - improve GPU hangcheck

  exynos:
   - Decon Exynos7870 support

  mediatek:
   - add OF graph support

  omap:
   - locking fixes

  bochs:
   - convert to gem/shmem from simpledrm

  v3d:
   - support big/super pages
   - add gemfs

  vc4:
   - BCM2712 support refactoring
   - add YUV444 format support

  udmabuf:
   - folio related fixes

  nouveau:
   - add panic support on nv50+"

* tag 'drm-next-2024-11-21' of https://gitlab.freedesktop.org/drm/kernel: (1583 commits)
  drm/xe/guc: Fix dereference before NULL check
  drm/amd: Fix initialization mistake for NBIO 7.7.0
  Revert "drm/amd/display: parse umc_info or vram_info based on ASIC"
  drm/amd/display: Fix failure to read vram info due to static BP_RESULT
  drm/amdgpu: enable GTT fallback handling for dGPUs only
  drm/amd/amdgpu: limit single process inside MES
  drm/fourcc: add AMD_FMT_MOD_TILE_GFX9_4K_D_X
  drm/amdgpu/mes12: correct kiq unmap latency
  drm/amdgpu: Support vcn and jpeg error info parsing
  drm/amd : Update MES API header file for v11 & v12
  drm/amd/amdkfd: add/remove kfd queues on start/stop KFD scheduling
  drm/amdkfd: change kfd process kref count at creation
  drm/amdgpu: Cleanup shift coding style
  drm/amd/amdgpu: Increase MES log buffer to dump mes scratch data
  drm/amdgpu: Implement virt req_ras_err_count
  drm/amdgpu: VF Query RAS Caps from Host if supported
  drm/amdgpu: Add msg handlers for SRIOV RAS Telemetry
  drm/amdgpu: Update SRIOV Exchange Headers for RAS Telemetry Support
  drm/amd/display: 3.2.309
  drm/amd/display: Adjust VSDB parser for replay feature
  ...

3 months agochar: tpm: cr50: Add new device/vendor ID 0x50666666
Jett Rink [Tue, 10 Sep 2024 19:11:14 +0000 (19:11 +0000)]
char: tpm: cr50: Add new device/vendor ID 0x50666666

Accept another DID:VID for the next generation Google TPM. This TPM
has the same Ti50 firmware and fulfills the same interface.

Suggested-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jett Rink <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
3 months agochar: tpm: cr50: Move i2c locking to request/relinquish locality ops
Jan Dabros [Thu, 10 Oct 2024 09:15:59 +0000 (09:15 +0000)]
char: tpm: cr50: Move i2c locking to request/relinquish locality ops

Move i2c locking primitives to request_locality and relinquish_locality
callbacks, what effectively blocks TPM bus for the whole duration of
logical TPM operation.

With this in place, cr50-equipped TPM may be shared with external CPUs -
assuming that underneath i2c controller driver is aware of this setup
(see i2c-designware-amdpsp as an example).

Signed-off-by: Jan Dabros <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
3 months agochar: tpm: cr50: Use generic request/relinquish locality ops
Jan Dabros [Thu, 10 Oct 2024 09:15:58 +0000 (09:15 +0000)]
char: tpm: cr50: Use generic request/relinquish locality ops

Instead of using static functions tpm_cr50_request_locality and
tpm_cr50_release_locality register callbacks from tpm class chip->ops
created for this purpose.

Signed-off-by: Jan Dabros <[email protected]>
Signed-off-by: Grzegorz Bernacki <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
3 months agotpm: ibmvtpm: Set TPM_OPS_AUTO_STARTUP flag on driver
Stefan Berger [Mon, 14 Oct 2024 14:16:43 +0000 (10:16 -0400)]
tpm: ibmvtpm: Set TPM_OPS_AUTO_STARTUP flag on driver

Set the TPM_OPS_AUTO_STARTUP on the driver so that the ibmvtpm driver now
uses tpm2_auto_startup and tpm1_auto_startup like many other drivers do.
Remove tpm_get_timeouts, tpm2_get_cc_attrs_tbl, and tpm2_sessions_init
calls from it since these will all be called in tpm2_auto_startup and
tpm1_auto_startup.

The exporting of the tpm2_session_init symbol was only necessary while the
ibmvtpm driver was calling this function. Since this is not the case
anymore, remove this symbol from being exported.

What is new for the ibmvtpm driver is that now tpm2_do_selftest and
tpm1_do_selftest will be called that send commands to the TPM to perform
or continue its selftest. However, the firmware should already have sent
these commands so that the TPM will not do much work at this time.

Signed-off-by: Stefan Berger <[email protected]>
Reviewed-by: Jarkko Sakkinen <[email protected]>
Signed-off-by: Jarkko Sakkinen <[email protected]>
3 months agoMerge tag 'sound-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai...
Linus Torvalds [Thu, 21 Nov 2024 22:39:31 +0000 (14:39 -0800)]
Merge tag 'sound-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "This is a relatively calm cycle, and majority of changes are about
  ASoC. There are little changes in the core side but we received lots
  of new drivers for new vendors.

  ALSA Core:
   - The new accel operation mode for compress-offload API; only the
     core part, the actual user will follow later

  ASoC:
   - Continued API simplification works
   - Renaming of the sh directory to Renesas
   - Factoring out of some of the common code for Realtek devices
   - Ussal ASoC Intel SOF, AMD and SoundWire updates
   - Support for Allwinner H616, AMD ACP 6.3 systems, AWInic AW88081,
     Cirrus Logic CS32L84, Everest ES8328, Iron Devices SMA1307,
     Longsoon I2S, NeoFidelity NTP8918 and NTP8835, Philips UDA1342,
     Qualcomm SM8750, RealTek RT721, and ST Microelectronics STM32MP25

  HD- and USB-audio:
   - Clean up of IRQ handling in legacy HD-audio driver
   - Fix soft lockup at disconnection of non-standard USB drivers
   - Scarlett2 mixer improvements
   - New quirks and cleanups in HD- and USB-audio"

* tag 'sound-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (278 commits)
  ALSA: hda: Poll jack events for LS7A HD-Audio
  ASoC: hdmi-codec: reorder channel allocation list
  ALSA: ump: Fix the wrong format specifier
  ASoC: Intel: soc-acpi-intel-lnl-match: add rt712_vb + rt1320 support
  ASoC: stm32: dfsdm: change rate upper limits
  ASoC: sma1307: fix uninitialized variable refence
  ASoC: dt-bindings: simple-mux: add idle-state property
  ASoc: simple-mux: add idle-state support
  ASoC: sdca: test adev before calling acpi_dev_for_each_child
  ASoC: SOF: ipc4-topology: remove redundant assignment to variable ret
  ASoC: amd: ps: fix the pcm device numbering for acp 6.3 platform
  ASoC: amd: acp: add soundwire machine driver for legacy stack
  ASoC: amd: acp: move get_acp63_cpu_pin_id() to common file
  ASoC: amd: ps: add soundwire machines for acp6.3 platform
  ASoC: amd: acp: add RT711, RT714 & RT1316 support for acp 6.3 platform
  ASoC: amd: acp: add rt722 based soundwire machines
  ALSA: compress_offload: Add missing descriptions in structs
  ALSA: 6fire: Release resources at card release
  ALSA: caiaq: Use snd_card_free_when_closed() at disconnection
  ALSA: us122l: Drop mmap_count field
  ...

3 months agoMerge tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa...
Linus Torvalds [Thu, 21 Nov 2024 21:19:29 +0000 (13:19 -0800)]
Merge tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Core:

   - drivers can now use a GPIO as a side channel for SMBus Alerts using
     a generic binding

   - regular stuff like mem leak fix, Makefile maintenance...

  Host improvements and refactoring:

   - All controllers using the 'remove_new' callback have been reverted
     to use the 'remove' callback

   - Intel SCH controller underwent significant refactoring, this brings
     love and a modern look to the driver

   - PIIX4 driver refactored to enable usage by other drivers (e.g., AMD
     ASF)

   - iMX/MXC improved message handling to reduce protocol overhead:
     Refactored DMA/non-DMA read/write and bus polling mechanisms to
     achieve this.

   - ACPI documentation for PIIX4

  New host features:

   - i2c-cadence support for atomic transfers

   - Qualcomm CII support for a 32MHz serial engine clock

  Deprecated features:

   - Dropped outdated support for AMD756 S4882 and NFORCE2 S4985. If
     somebody misses this, Jean will rewrite support using the proper
     i2c mux framework.

  New hardware IDs for existing drivers:

   - Intel Panther Lake

   - S32G2/S32G3 SoCs

   - HJMC01 DesignWare ACPI HID

   - PIC64GX to Microchip Core

   - Qualcomm SDM670 to Qualcomm CCI

  New drivers:

   - AMD ASF

   - Realtek RTL I2C Controller

  at24 updates:

   - add support for the lockable page on ST M24256E"

* tag 'i2c-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (59 commits)
  docs: i2c: piix4: Add ACPI section
  i2c: Add driver for the RTL9300 I2C controller
  i2c: qcom-cci: Remove unused struct member cci_clk_rate
  dt-bindings: i2c: Add Realtek RTL I2C Controller
  i2c: busses: Use *-y instead of *-objs in Makefile
  i2c: imx: add support for S32G2/S32G3 SoCs
  dt-bindings: i2c: imx: add SoC specific compatible strings for S32G
  i2c: qcom-cci: Remove the unused variable cci_clk_rate
  i2c: Drop legacy muxing pseudo-drivers
  i2c: imx: prevent rescheduling in non dma mode
  i2c: imx: separate atomic, dma and non-dma use case
  i2c: imx: do not poll for bus busy in single master mode
  i2c: designware: Add a new ACPI HID for HJMC01 I2C controller
  i2c: qcom-geni: Keep comment why interrupts start disabled
  dt-bindings: i2c: microchip: corei2c: Add PIC64GX as compatible with driver
  i2c: designware: constify abort_sources
  i2c: Switch back to struct platform_driver::remove()
  i2c: qcom-geni: Support systems with 32MHz serial engine clock
  i2c: qcom-cci: Stop complaining about DT set clock rate
  dt-bindings: i2c: qcom-cci: Document SDM670 compatible
  ...

3 months agoMerge tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg...
Linus Torvalds [Thu, 21 Nov 2024 20:40:50 +0000 (12:40 -0800)]
Merge tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd

Pull iommufd updates from Jason Gunthorpe:
 "Several new features and uAPI for iommufd:

   - IOMMU_IOAS_MAP_FILE allows passing in a file descriptor as the
     backing memory for an iommu mapping. To date VFIO/iommufd have used
     VMA's and pin_user_pages(), this now allows using memfds and
     memfd_pin_folios(). Notably this creates a pure folio path from the
     memfd to the iommu page table where memory is never broken down to
     PAGE_SIZE.

   - IOMMU_IOAS_CHANGE_PROCESS moves the pinned page accounting between
     two processes. Combined with the above this allows iommufd to
     support a VMM re-start using exec() where something like qemu would
     exec() a new version of itself and fd pass the memfds/iommufd/etc
     to the new process. The memfd allows DMA access to the memory to
     continue while the new process is getting setup, and the
     CHANGE_PROCESS updates all the accounting.

   - Support for fault reporting to userspace on non-PRI HW, such as ARM
     stall-mode embedded devices.

   - IOMMU_VIOMMU_ALLOC introduces the concept of a HW/driver backed
     virtual iommu. This will be used by VMMs to access hardware
     features that are contained with in a VM. The first use is to
     inform the kernel of the virtual SID to physical SID mapping when
     issuing SID based invalidation on ARM. Further uses will tie HW
     features that are directly accessed by the VM, such as invalidation
     queue assignment and others.

   - IOMMU_VDEVICE_ALLOC informs the kernel about the mapping of virtual
     device to physical device within a VIOMMU. Minimially this is used
     to translate VM issued cache invalidation commands from virtual to
     physical device IDs.

   - Enhancements to IOMMU_HWPT_INVALIDATE and IOMMU_HWPT_ALLOC to work
     with the VIOMMU

   - ARM SMMuv3 support for nested translation. Using the VIOMMU and
     VDEVICE the driver can model this HW's behavior for nested
     translation. This includes a shared branch from Will"

* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd: (51 commits)
  iommu/arm-smmu-v3: Import IOMMUFD module namespace
  iommufd: IOMMU_IOAS_CHANGE_PROCESS selftest
  iommufd: Add IOMMU_IOAS_CHANGE_PROCESS
  iommufd: Lock all IOAS objects
  iommufd: Export do_update_pinned
  iommu/arm-smmu-v3: Support IOMMU_HWPT_INVALIDATE using a VIOMMU object
  iommu/arm-smmu-v3: Allow ATS for IOMMU_DOMAIN_NESTED
  iommu/arm-smmu-v3: Use S2FWB for NESTED domains
  iommu/arm-smmu-v3: Support IOMMU_DOMAIN_NESTED
  iommu/arm-smmu-v3: Support IOMMU_VIOMMU_ALLOC
  Documentation: userspace-api: iommufd: Update vDEVICE
  iommufd/selftest: Add vIOMMU coverage for IOMMU_HWPT_INVALIDATE ioctl
  iommufd/selftest: Add IOMMU_TEST_OP_DEV_CHECK_CACHE test command
  iommufd/selftest: Add mock_viommu_cache_invalidate
  iommufd/viommu: Add iommufd_viommu_find_dev helper
  iommu: Add iommu_copy_struct_from_full_user_array helper
  iommufd: Allow hwpt_id to carry viommu_id for IOMMU_HWPT_INVALIDATE
  iommu/viommu: Add cache_invalidate to iommufd_viommu_ops
  iommufd/selftest: Add IOMMU_VDEVICE_ALLOC test coverage
  iommufd/viommu: Add IOMMUFD_OBJ_VDEVICE and IOMMU_VDEVICE_ALLOC ioctl
  ...

3 months agoMerge tag 'dma-mapping-6.13-2024-11-19' of git://git.infradead.org/users/hch/dma...
Linus Torvalds [Thu, 21 Nov 2024 19:28:39 +0000 (11:28 -0800)]
Merge tag 'dma-mapping-6.13-2024-11-19' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping updates from Christoph Hellwig:

 - improve the DMA API tracing code (Sean Anderson)

 - misc cleanups (Christoph Hellwig, Sui Jingfeng)

 - fix pointer abuse when finding the shared DMA pool (Geert
   Uytterhoeven)

 - fix a deadlock in dma-debug (Levi Yun)

* tag 'dma-mapping-6.13-2024-11-19' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: save base/size instead of pointer to shared DMA pool
  dma-mapping: fix swapped dir/flags arguments to trace_dma_alloc_sgt_err
  dma-mapping: drop unneeded includes from dma-mapping.h
  dma-mapping: trace more error paths
  dma-mapping: use trace_dma_alloc for dma_alloc* instead of using trace_dma_map
  dma-mapping: trace dma_alloc/free direction
  dma-mapping: use macros to define events in a class
  dma-mapping: remove an outdated comment from dma-map-ops.h
  dma-debug: remove DMA_API_DEBUG_SG
  dma-debug: store a phys_addr_t in struct dma_debug_entry
  dma-debug: fix a possible deadlock on radix_lock

3 months agoMerge tag 'configfs-6.13-2024-11-19' of git://git.infradead.org/users/hch/configfs
Linus Torvalds [Thu, 21 Nov 2024 19:26:38 +0000 (11:26 -0800)]
Merge tag 'configfs-6.13-2024-11-19' of git://git.infradead.org/users/hch/configfs

Pull configfs updates from Christoph Hellwig:

 - remove unused code (Dr. David Alan Gilbert)

 - improve item creation performance (Seamus Connor)

* tag 'configfs-6.13-2024-11-19' of git://git.infradead.org/users/hch/configfs:
  configfs: improve item creation performance
  configfs: remove unused configfs_hash_and_remove

3 months agoMerge tag 'jfs-6.13' of github.com:kleikamp/linux-shaggy
Linus Torvalds [Thu, 21 Nov 2024 17:59:59 +0000 (09:59 -0800)]
Merge tag 'jfs-6.13' of github.com:kleikamp/linux-shaggy

Pull jfs updates from Dave Kleikamp:
 "A few more patches to add sanity checks in jfs"

* tag 'jfs-6.13' of github.com:kleikamp/linux-shaggy:
  jfs: add a check to prevent array-index-out-of-bounds in dbAdjTree
  jfs: xattr: check invalid xattr size more strictly
  jfs: fix array-index-out-of-bounds in jfs_readdir
  jfs: fix shift-out-of-bounds in dbSplit
  jfs: array-index-out-of-bounds fix in dtReadFirst

3 months agoMerge tag 'dlm-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Linus Torvalds [Thu, 21 Nov 2024 17:57:46 +0000 (09:57 -0800)]
Merge tag 'dlm-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm

Pull dlm updates from David Teigland:

 - Fix recovery of locks that are being converted between PR/CW modes

 - Fix cleanup of rsb list if recovery is interrupted during
   recover_members

 - Fix null dereference in debug code if dlm api is called improperly

 - Fix wrong args passed to trace function

 - Move error checks out of add_to_waiters so the function can't fail

 - Clean up some code for configfs

* tag 'dlm-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
  dlm: fix dlm_recover_members refcount on error
  dlm: fix recovery of middle conversions
  dlm: make add_to_waiters() that it can't fail
  dlm: dlm_config_info config fields to unsigned int
  dlm: use dlm_config as only cluster configuration
  dlm: handle port as __be16 network byte order
  dlm: disallow different configs nodeid storages
  dlm: fix possible lkb_resource null dereference
  dlm: fix swapped args sb_flags vs sb_status

3 months agoMerge tag 'fsnotify_for_v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Thu, 21 Nov 2024 17:55:45 +0000 (09:55 -0800)]
Merge tag 'fsnotify_for_v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs

Pull fsnotify updates from Jan Kara:
 "A couple of smaller random fsnotify fixes"

* tag 'fsnotify_for_v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: Fix ordering of iput() and watched_objects decrement
  fsnotify: fix sending inotify event with unexpected filename
  fanotify: allow reporting errors on failure to open fd
  fsnotify, lsm: Decouple fsnotify from lsm

3 months agoMerge tag 'reiserfs_delete' of git://git.kernel.org/pub/scm/linux/kernel/git/jack...
Linus Torvalds [Thu, 21 Nov 2024 17:50:18 +0000 (09:50 -0800)]
Merge tag 'reiserfs_delete' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs

Pull reiserfs removal from Jan Kara:
 "The deprecation period of reiserfs is ending at the end of this year
  so it is time to remove it"

* tag 'reiserfs_delete' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  reiserfs: The last commit

3 months agoMerge tag 'for_v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Linus Torvalds [Thu, 21 Nov 2024 17:47:44 +0000 (09:47 -0800)]
Merge tag 'for_v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs

Pull quota and isofs updates from Jan Kara:
 "Fix a memory leak in isofs and a cleanup of includes in quota"

* tag 'for_v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  dquot.c: get rid of include ../internal.h
  isofs: avoid memory leak in iocharset

3 months agoMerge tag 'xfs-6.13-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Linus Torvalds [Thu, 21 Nov 2024 17:20:07 +0000 (09:20 -0800)]
Merge tag 'xfs-6.13-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux

Pull xfs updates from Carlos Maiolino:
 "The bulk of this pull request is a major rework that Darrick and
  Christoph have been doing on XFS's real-time volume, coupled with a
  few features to support this rework. It does also includes some bug
  fixes.

   - convert perag to use xarrays

   - create a new generic allocation group structure

   - add metadata inode dir trees

   - create in-core rt allocation groups

   - shard the RT section into allocation groups

   - persist quota options with the enw metadata dir tree

   - enable quota for RT volumes

   - enable metadata directory trees

   - some bugfixes"

* tag 'xfs-6.13-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (146 commits)
  xfs: port ondisk structure checks from xfs/122 to the kernel
  xfs: separate space btree structures in xfs_ondisk.h
  xfs: convert struct typedefs in xfs_ondisk.h
  xfs: enable metadata directory feature
  xfs: enable realtime quota again
  xfs: update sb field checks when metadir is turned on
  xfs: reserve quota for realtime files correctly
  xfs: create quota preallocation watermarks for realtime quota
  xfs: report realtime block quota limits on realtime directories
  xfs: persist quota flags with metadir
  xfs: advertise realtime quota support in the xqm stat files
  xfs: scrub quota file metapaths
  xfs: fix chown with rt quota
  xfs: use metadir for quota inodes
  xfs: refactor xfs_qm_destroy_quotainos
  xfs: use rtgroup busy extent list for FITRIM
  xfs: implement busy extent tracking for rtgroups
  xfs: port the perag discard code to handle generic groups
  xfs: move the min and max group block numbers to xfs_group
  xfs: adjust min_block usage in xfs_verify_agbno
  ...

3 months agoMerge tag 'erofs-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang...
Linus Torvalds [Thu, 21 Nov 2024 17:17:33 +0000 (09:17 -0800)]
Merge tag 'erofs-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs

Pull erofs updates from Gao Xiang:
 "There is no outstanding feature for this cycle. The most useful
  changes are SEEK_{DATA,HOLE} support and some decompression
  micro-optimization. Other than those, there are some bugfixes and
  cleanups as usual:

   - Add SEEK_{DATA,HOLE} support

   - Free redundant pclusters if no cached compressed data is valid

   - Add sysfs entry to drop internal caches

   - Several bugfixes & cleanups"

* tag 'erofs-for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: handle NONHEAD !delta[1] lclusters gracefully
  erofs: clarify direct I/O support
  erofs: fix blksize < PAGE_SIZE for file-backed mounts
  erofs: get rid of `buf->kmap_type`
  erofs: fix file-backed mounts over FUSE
  erofs: simplify definition of the log functions
  erofs: add sysfs node to drop internal caches
  erofs: free pclusters if no cached folio is attached
  erofs: sunset `struct erofs_workgroup`
  erofs: move erofs_workgroup operations into zdata.c
  erofs: get rid of erofs_{find,insert}_workgroup
  erofs: add SEEK_{DATA,HOLE} support

3 months agosmb: prevent use-after-free due to open_cached_dir error paths
Paul Aurich [Mon, 18 Nov 2024 21:50:27 +0000 (13:50 -0800)]
smb: prevent use-after-free due to open_cached_dir error paths

If open_cached_dir() encounters an error parsing the lease from the
server, the error handling may race with receiving a lease break,
resulting in open_cached_dir() freeing the cfid while the queued work is
pending.

Update open_cached_dir() to drop refs rather than directly freeing the
cfid.

Have cached_dir_lease_break(), cfids_laundromat_worker(), and
invalidate_all_cached_dirs() clear has_lease immediately while still
holding cfids->cfid_list_lock, and then use this to also simplify the
reference counting in cfids_laundromat_worker() and
invalidate_all_cached_dirs().

Fixes this KASAN splat (which manually injects an error and lease break
in open_cached_dir()):

==================================================================
BUG: KASAN: slab-use-after-free in smb2_cached_lease_break+0x27/0xb0
Read of size 8 at addr ffff88811cc24c10 by task kworker/3:1/65

CPU: 3 UID: 0 PID: 65 Comm: kworker/3:1 Not tainted 6.12.0-rc6-g255cf264e6e5-dirty #87
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020
Workqueue: cifsiod smb2_cached_lease_break
Call Trace:
 <TASK>
 dump_stack_lvl+0x77/0xb0
 print_report+0xce/0x660
 kasan_report+0xd3/0x110
 smb2_cached_lease_break+0x27/0xb0
 process_one_work+0x50a/0xc50
 worker_thread+0x2ba/0x530
 kthread+0x17c/0x1c0
 ret_from_fork+0x34/0x60
 ret_from_fork_asm+0x1a/0x30
 </TASK>

Allocated by task 2464:
 kasan_save_stack+0x33/0x60
 kasan_save_track+0x14/0x30
 __kasan_kmalloc+0xaa/0xb0
 open_cached_dir+0xa7d/0x1fb0
 smb2_query_path_info+0x43c/0x6e0
 cifs_get_fattr+0x346/0xf10
 cifs_get_inode_info+0x157/0x210
 cifs_revalidate_dentry_attr+0x2d1/0x460
 cifs_getattr+0x173/0x470
 vfs_statx_path+0x10f/0x160
 vfs_statx+0xe9/0x150
 vfs_fstatat+0x5e/0xc0
 __do_sys_newfstatat+0x91/0xf0
 do_syscall_64+0x95/0x1a0
 entry_SYSCALL_64_after_hwframe+0x76/0x7e

Freed by task 2464:
 kasan_save_stack+0x33/0x60
 kasan_save_track+0x14/0x30
 kasan_save_free_info+0x3b/0x60
 __kasan_slab_free+0x51/0x70
 kfree+0x174/0x520
 open_cached_dir+0x97f/0x1fb0
 smb2_query_path_info+0x43c/0x6e0
 cifs_get_fattr+0x346/0xf10
 cifs_get_inode_info+0x157/0x210
 cifs_revalidate_dentry_attr+0x2d1/0x460
 cifs_getattr+0x173/0x470
 vfs_statx_path+0x10f/0x160
 vfs_statx+0xe9/0x150
 vfs_fstatat+0x5e/0xc0
 __do_sys_newfstatat+0x91/0xf0
 do_syscall_64+0x95/0x1a0
 entry_SYSCALL_64_after_hwframe+0x76/0x7e

Last potentially related work creation:
 kasan_save_stack+0x33/0x60
 __kasan_record_aux_stack+0xad/0xc0
 insert_work+0x32/0x100
 __queue_work+0x5c9/0x870
 queue_work_on+0x82/0x90
 open_cached_dir+0x1369/0x1fb0
 smb2_query_path_info+0x43c/0x6e0
 cifs_get_fattr+0x346/0xf10
 cifs_get_inode_info+0x157/0x210
 cifs_revalidate_dentry_attr+0x2d1/0x460
 cifs_getattr+0x173/0x470
 vfs_statx_path+0x10f/0x160
 vfs_statx+0xe9/0x150
 vfs_fstatat+0x5e/0xc0
 __do_sys_newfstatat+0x91/0xf0
 do_syscall_64+0x95/0x1a0
 entry_SYSCALL_64_after_hwframe+0x76/0x7e

The buggy address belongs to the object at ffff88811cc24c00
 which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 16 bytes inside of
 freed 1024-byte region [ffff88811cc24c00ffff88811cc25000)

Cc: [email protected]
Signed-off-by: Paul Aurich <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agosmb: Don't leak cfid when reconnect races with open_cached_dir
Paul Aurich [Mon, 18 Nov 2024 21:50:26 +0000 (13:50 -0800)]
smb: Don't leak cfid when reconnect races with open_cached_dir

open_cached_dir() may either race with the tcon reconnection even before
compound_send_recv() or directly trigger a reconnection via
SMB2_open_init() or SMB_query_info_init().

The reconnection process invokes invalidate_all_cached_dirs() via
cifs_mark_open_files_invalid(), which removes all cfids from the
cfids->entries list but doesn't drop a ref if has_lease isn't true. This
results in the currently-being-constructed cfid not being on the list,
but still having a refcount of 2. It leaks if returned from
open_cached_dir().

Fix this by setting cfid->has_lease when the ref is actually taken; the
cfid will not be used by other threads until it has a valid time.

Addresses these kmemleaks:

unreferenced object 0xffff8881090c4000 (size 1024):
  comm "bash", pid 1860, jiffies 4295126592
  hex dump (first 32 bytes):
    00 01 00 00 00 00 ad de 22 01 00 00 00 00 ad de  ........".......
    00 ca 45 22 81 88 ff ff f8 dc 4f 04 81 88 ff ff  ..E"......O.....
  backtrace (crc 6f58c20f):
    [<ffffffff8b895a1e>] __kmalloc_cache_noprof+0x2be/0x350
    [<ffffffff8bda06e3>] open_cached_dir+0x993/0x1fb0
    [<ffffffff8bdaa750>] cifs_readdir+0x15a0/0x1d50
    [<ffffffff8b9a853f>] iterate_dir+0x28f/0x4b0
    [<ffffffff8b9a9aed>] __x64_sys_getdents64+0xfd/0x200
    [<ffffffff8cf6da05>] do_syscall_64+0x95/0x1a0
    [<ffffffff8d00012f>] entry_SYSCALL_64_after_hwframe+0x76/0x7e
unreferenced object 0xffff8881044fdcf8 (size 8):
  comm "bash", pid 1860, jiffies 4295126592
  hex dump (first 8 bytes):
    00 cc cc cc cc cc cc cc                          ........
  backtrace (crc 10c106a9):
    [<ffffffff8b89a3d3>] __kmalloc_node_track_caller_noprof+0x363/0x480
    [<ffffffff8b7d7256>] kstrdup+0x36/0x60
    [<ffffffff8bda0700>] open_cached_dir+0x9b0/0x1fb0
    [<ffffffff8bdaa750>] cifs_readdir+0x15a0/0x1d50
    [<ffffffff8b9a853f>] iterate_dir+0x28f/0x4b0
    [<ffffffff8b9a9aed>] __x64_sys_getdents64+0xfd/0x200
    [<ffffffff8cf6da05>] do_syscall_64+0x95/0x1a0
    [<ffffffff8d00012f>] entry_SYSCALL_64_after_hwframe+0x76/0x7e

And addresses these BUG splats when unmounting the SMB filesystem:

BUG: Dentry ffff888140590ba0{i=1000000000080,n=/}  still in use (2) [unmount of cifs cifs]
WARNING: CPU: 3 PID: 3433 at fs/dcache.c:1536 umount_check+0xd0/0x100
Modules linked in:
CPU: 3 UID: 0 PID: 3433 Comm: bash Not tainted 6.12.0-rc4-g850925a8133c-dirty #49
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020
RIP: 0010:umount_check+0xd0/0x100
Code: 8d 7c 24 40 e8 31 5a f4 ff 49 8b 54 24 40 41 56 49 89 e9 45 89 e8 48 89 d9 41 57 48 89 de 48 c7 c7 80 e7 db ac e8 f0 72 9a ff <0f> 0b 58 31 c0 5a 5b 5d 41 5c 41 5d 41 5e 41 5f e9 2b e5 5d 01 41
RSP: 0018:ffff88811cc27978 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff888140590ba0 RCX: ffffffffaaf20bae
RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff8881f6fb6f40
RBP: ffff8881462ec000 R08: 0000000000000001 R09: ffffed1023984ee3
R10: ffff88811cc2771f R11: 00000000016cfcc0 R12: ffff888134383e08
R13: 0000000000000002 R14: ffff8881462ec668 R15: ffffffffaceab4c0
FS:  00007f23bfa98740(0000) GS:ffff8881f6f80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556de4a6f808 CR3: 0000000123c80000 CR4: 0000000000350ef0
Call Trace:
 <TASK>
 d_walk+0x6a/0x530
 shrink_dcache_for_umount+0x6a/0x200
 generic_shutdown_super+0x52/0x2a0
 kill_anon_super+0x22/0x40
 cifs_kill_sb+0x159/0x1e0
 deactivate_locked_super+0x66/0xe0
 cleanup_mnt+0x140/0x210
 task_work_run+0xfb/0x170
 syscall_exit_to_user_mode+0x29f/0x2b0
 do_syscall_64+0xa1/0x1a0
 entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f23bfb93ae7
Code: ff ff ff ff c3 66 0f 1f 44 00 00 48 8b 0d 11 93 0d 00 f7 d8 64 89 01 b8 ff ff ff ff eb bf 0f 1f 44 00 00 b8 50 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d e9 92 0d 00 f7 d8 64 89 01 48
RSP: 002b:00007ffee9138598 EFLAGS: 00000246 ORIG_RAX: 0000000000000050
RAX: 0000000000000000 RBX: 0000558f1803e9a0 RCX: 00007f23bfb93ae7
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000558f1803e9a0
RBP: 0000558f1803e600 R08: 0000000000000007 R09: 0000558f17fab610
R10: d91d5ec34ab757b0 R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000000000 R14: 0000000000000015 R15: 0000000000000000
 </TASK>
irq event stamp: 1163486
hardirqs last  enabled at (1163485): [<ffffffffac98d344>] _raw_spin_unlock_irqrestore+0x34/0x60
hardirqs last disabled at (1163486): [<ffffffffac97dcfc>] __schedule+0xc7c/0x19a0
softirqs last  enabled at (1163482): [<ffffffffab79a3ee>] __smb_send_rqst+0x3de/0x990
softirqs last disabled at (1163480): [<ffffffffac2314f1>] release_sock+0x21/0xf0
---[ end trace 0000000000000000 ]---

VFS: Busy inodes after unmount of cifs (cifs)
------------[ cut here ]------------
kernel BUG at fs/super.c:661!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
CPU: 1 UID: 0 PID: 3433 Comm: bash Tainted: G        W          6.12.0-rc4-g850925a8133c-dirty #49
Tainted: [W]=WARN
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020
RIP: 0010:generic_shutdown_super+0x290/0x2a0
Code: e8 15 7c f7 ff 48 8b 5d 28 48 89 df e8 09 7c f7 ff 48 8b 0b 48 89 ee 48 8d 95 68 06 00 00 48 c7 c7 80 7f db ac e8 00 69 af ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 90 90 90 90 90 90
RSP: 0018:ffff88811cc27a50 EFLAGS: 00010246
RAX: 000000000000003e RBX: ffffffffae994420 RCX: 0000000000000027
RDX: 0000000000000000 RSI: ffffffffab06180e RDI: ffff8881f6eb18c8
RBP: ffff8881462ec000 R08: 0000000000000001 R09: ffffed103edd6319
R10: ffff8881f6eb18cb R11: 00000000016d3158 R12: ffff8881462ec9c0
R13: ffff8881462ec050 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f23bfa98740(0000) GS:ffff8881f6e80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8364005d68 CR3: 0000000123c80000 CR4: 0000000000350ef0
Call Trace:
 <TASK>
 kill_anon_super+0x22/0x40
 cifs_kill_sb+0x159/0x1e0
 deactivate_locked_super+0x66/0xe0
 cleanup_mnt+0x140/0x210
 task_work_run+0xfb/0x170
 syscall_exit_to_user_mode+0x29f/0x2b0
 do_syscall_64+0xa1/0x1a0
 entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f23bfb93ae7
 </TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
RIP: 0010:generic_shutdown_super+0x290/0x2a0
Code: e8 15 7c f7 ff 48 8b 5d 28 48 89 df e8 09 7c f7 ff 48 8b 0b 48 89 ee 48 8d 95 68 06 00 00 48 c7 c7 80 7f db ac e8 00 69 af ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 90 90 90 90 90 90
RSP: 0018:ffff88811cc27a50 EFLAGS: 00010246
RAX: 000000000000003e RBX: ffffffffae994420 RCX: 0000000000000027
RDX: 0000000000000000 RSI: ffffffffab06180e RDI: ffff8881f6eb18c8
RBP: ffff8881462ec000 R08: 0000000000000001 R09: ffffed103edd6319
R10: ffff8881f6eb18cb R11: 00000000016d3158 R12: ffff8881462ec9c0
R13: ffff8881462ec050 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f23bfa98740(0000) GS:ffff8881f6e80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8364005d68 CR3: 0000000123c80000 CR4: 0000000000350ef0

This reproduces eventually with an SMB mount and two shells running
these loops concurrently

- while true; do
      cd ~; sleep 1;
      for i in {1..3}; do cd /mnt/test/subdir;
          echo $PWD; sleep 1; cd ..; echo $PWD; sleep 1;
      done;
      echo ...;
  done
- while true; do
      iptables -F OUTPUT; mount -t cifs -a;
      for _ in {0..2}; do ls /mnt/test/subdir/ | wc -l; done;
      iptables -I OUTPUT -p tcp --dport 445 -j DROP;
      sleep 10
      echo "unmounting"; umount -l -t cifs -a; echo "done unmounting";
      sleep 20
      echo "recovering"; iptables -F OUTPUT;
      sleep 10;
  done

Fixes: ebe98f1447bb ("cifs: enable caching of directories for which a lease is held")
Fixes: 5c86919455c1 ("smb: client: fix use-after-free in smb2_query_info_compound()")
Cc: [email protected]
Signed-off-by: Paul Aurich <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agosmb: client: handle max length for SMB symlinks
Paulo Alcantara [Mon, 18 Nov 2024 15:35:16 +0000 (12:35 -0300)]
smb: client: handle max length for SMB symlinks

We can't use PATH_MAX for SMB symlinks because

  (1) Windows Server will fail FSCTL_SET_REPARSE_POINT with
      STATUS_IO_REPARSE_DATA_INVALID when input buffer is larger than
      16K, as specified in MS-FSA 2.1.5.10.37.

  (2) The client won't be able to parse large SMB responses that
      includes SMB symlink path within SMB2_CREATE or SMB2_IOCTL
      responses.

Fix this by defining a maximum length value (4060) for SMB symlinks
that both client and server can handle.

Cc: David Howells <[email protected]>
Cc: [email protected]
Signed-off-by: Paulo Alcantara (Red Hat) <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agosmb: client: get rid of bounds check in SMB2_ioctl_init()
Paulo Alcantara [Mon, 18 Nov 2024 15:35:15 +0000 (12:35 -0300)]
smb: client: get rid of bounds check in SMB2_ioctl_init()

smb2_set_next_command() no longer squashes request iovs into a single
iov, so the bounds check can be dropped.

Cc: David Howells <[email protected]>
Signed-off-by: Paulo Alcantara (Red Hat) <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agosmb: client: improve compound padding in encryption
Paulo Alcantara [Mon, 18 Nov 2024 15:35:14 +0000 (12:35 -0300)]
smb: client: improve compound padding in encryption

After commit f7f291e14dde ("cifs: fix oops during encryption"), the
encryption layer can handle vmalloc'd buffers as well as kmalloc'd
buffers, so there is no need to inefficiently squash request iovs
into a single one to handle padding in compound requests.

Cc: David Howells <[email protected]>
Signed-off-by: Paulo Alcantara (Red Hat) <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agosmb3: request handle caching when caching directories
Steve French [Mon, 18 Nov 2024 18:19:46 +0000 (12:19 -0600)]
smb3: request handle caching when caching directories

This client was only requesting READ caching, not READ and HANDLE caching
in the LeaseState on the open requests we send for directories.  To
delay closing a handle (e.g. for caching directory contents) we should
be requesting HANDLE as well as READ (as we already do for deferred
close of files).   See MS-SMB2 3.3.1.4 e.g.

Cc: [email protected]
Signed-off-by: Steve French <[email protected]>
3 months agocifs: Recognize SFU char/block devices created by Windows NFS server on Windows Serve...
Pali Rohár [Thu, 3 Oct 2024 19:39:03 +0000 (21:39 +0200)]
cifs: Recognize SFU char/block devices created by Windows NFS server on Windows Server <<2012

Windows NFS server versions on Windows Server older than 2012 release use
for storing char and block devices modified SFU format, not compatible with
the original SFU. Windows NFS server on Windows Server 2012 and new
versions use different format (reparse points), not related to SFU-style.

SFU / SUA / Interix subsystem stores the major and major numbers as pair of
64-bit integer, but Windows NFS server stores as pair of 32-bit integers.

Which makes char and block devices between Windows NFS server <<2012 and
Windows SFU/SUA/Interix subsytem incompatible.

So improve Linux SMB client.

When SFU mode is enabled (mount option -o sfu is specified) then recognize
also these kind of char and block devices and its major and minor numbers,
which are used by Windows Server versions older than 2012.

Signed-off-by: Pali Rohár <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agoCIFS: New mount option for cifs.upcall namespace resolution
Ritvik Budhiraja [Mon, 11 Nov 2024 11:43:51 +0000 (11:43 +0000)]
CIFS: New mount option for cifs.upcall namespace resolution

In the current implementation, the SMB filesystem on a mount point can
trigger upcalls from the kernel to the userspace to enable certain
functionalities like spnego, dns_resolution, amongst others. These upcalls
usually either happen in the context of the mount or in the context of an
application/user. The upcall handler for cifs, cifs.upcall already has
existing code which switches the namespaces to the caller's namespace
before handling the upcall. This behaviour is expected for scenarios like
multiuser mounts, but might not cover all single user scenario with
services such as Kubernetes, where the mount can happen from different
locations such as on the host, from an app container, or a driver pod
which does the mount on behalf of a different pod.

This patch introduces a new mount option called upcall_target, to
customise the upcall behaviour. upcall_target can take 'mount' and 'app'
as possible values. This aids use cases like Kubernetes where the mount
happens on behalf of the application in another container altogether.
Having this new mount option allows the mount command to specify where the
upcall should happen: 'mount' for resolving the upcall to the host
namespace, and 'app' for resolving the upcall to the ns of the calling
thread. This will enable both the scenarios where the Kerberos credentials
can be found on the application namespace or the host namespace to which
just the mount operation is "delegated".

Reviewed-by: Shyam Prasad <[email protected]>
Reviewed-by: Bharath S M <[email protected]>
Reviewed-by: Ronnie Sahlberg <[email protected]>
Signed-off-by: Ritvik Budhiraja <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agosmb/client: Prevent error pointer dereference
Dan Carpenter [Wed, 20 Nov 2024 17:18:31 +0000 (20:18 +0300)]
smb/client: Prevent error pointer dereference

The cifs_sb_tlink() function can return error pointers, but this code
dereferences it before checking for error pointers.  Re-order the code
to fix that.

Fixes: 0f9b6b045bb2 ("fs/smb/client: implement chmod() for SMB3 POSIX Extensions")
Signed-off-by: Dan Carpenter <[email protected]>
Reviewed-by: Bharath SM <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agofs/smb/client: implement chmod() for SMB3 POSIX Extensions
Ralph Boehme [Thu, 14 Nov 2024 10:05:13 +0000 (11:05 +0100)]
fs/smb/client: implement chmod() for SMB3 POSIX Extensions

The NT ACL format for an SMB3 POSIX Extensions chmod() is a single ACE with the
magic S-1-5-88-3-mode SID:

  NT Security Descriptor
      Revision: 1
      Type: 0x8004, Self Relative, DACL Present
      Offset to owner SID: 56
      Offset to group SID: 124
      Offset to SACL: 0
      Offset to DACL: 20
      Owner: S-1-5-21-3177838999-3893657415-1037673384-1000
      Group: S-1-22-2-1000
      NT User (DACL) ACL
          Revision: NT4 (2)
          Size: 36
          Num ACEs: 1
          NT ACE: S-1-5-88-3-438, flags 0x00, Access Allowed, mask 0x00000000
              Type: Access Allowed
              NT ACE Flags: 0x00
              Size: 28
              Access required: 0x00000000
              SID: S-1-5-88-3-438

Owner and Group should be NULL, but the server is not required to fail the
request if they are present.

Signed-off-by: Ralph Boehme <[email protected]>
Cc: [email protected]
Signed-off-by: Steve French <[email protected]>
3 months agosmb: cached directories can be more than root file handle
Paul Aurich [Fri, 8 Nov 2024 22:29:02 +0000 (14:29 -0800)]
smb: cached directories can be more than root file handle

Update this log message since cached fids may represent things other
than the root of a mount.

Fixes: e4029e072673 ("cifs: find and use the dentry for cached non-root directories also")
Signed-off-by: Paul Aurich <[email protected]>
Reviewed-by: Bharath SM <[email protected]>
Signed-off-by: Steve French <[email protected]>
3 months agoMerge tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev...
Linus Torvalds [Thu, 21 Nov 2024 16:28:08 +0000 (08:28 -0800)]
Merge tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Paolo Abeni:
 "The most significant set of changes is the per netns RTNL. The new
  behavior is disabled by default, regression risk should be contained.

  Notably the new config knob PTP_1588_CLOCK_VMCLOCK will inherit its
  default value from PTP_1588_CLOCK_KVM, as the first is intended to be
  a more reliable replacement for the latter.

  Core:

   - Started a very large, in-progress, effort to make the RTNL lock
     scope per network-namespace, thus reducing the lock contention
     significantly in the containerized use-case, comprising:
       - RCU-ified some relevant slices of the FIB control path
       - introduce basic per netns locking helpers
       - namespacified the IPv4 address hash table
       - remove rtnl_register{,_module}() in favour of
         rtnl_register_many()
       - refactor rtnl_{new,del,set}link() moving as much validation as
         possible out of RTNL lock
       - convert all phonet doit() and dumpit() handlers to RCU
       - convert IPv4 addresses manipulation to per-netns RTNL
       - convert virtual interface creation to per-netns RTNL
     the per-netns lock infrastructure is guarded by the
     CONFIG_DEBUG_NET_SMALL_RTNL knob, disabled by default ad interim.

   - Introduce NAPI suspension, to efficiently switching between busy
     polling (NAPI processing suspended) and normal processing.

   - Migrate the IPv4 routing input, output and control path from direct
     ToS usage to DSCP macros. This is a work in progress to make ECN
     handling consistent and reliable.

   - Add drop reasons support to the IPv4 rotue input path, allowing
     better introspection in case of packets drop.

   - Make FIB seqnum lockless, dropping RTNL protection for read access.

   - Make inet{,v6} addresses hashing less predicable.

   - Allow providing timestamp OPT_ID via cmsg, to correlate TX packets
     and timestamps

  Things we sprinkled into general kernel code:

   - Add small file operations for debugfs, to reduce the struct ops
     size.

   - Refactoring and optimization for the implementation of page_frag
     API, This is a preparatory work to consolidate the page_frag
     implementation.

  Netfilter:

   - Optimize set element transactions to reduce memory consumption

   - Extended netlink error reporting for attribute parser failure.

   - Make legacy xtables configs user selectable, giving users the
     option to configure iptables without enabling any other config.

   - Address a lot of false-positive RCU issues, pointed by recent CI
     improvements.

  BPF:

   - Put xsk sockets on a struct diet and add various cleanups. Overall,
     this helps to bump performance by 12% for some workloads.

   - Extend BPF selftests to increase coverage of XDP features in
     combination with BPF cpumap.

   - Optimize and homogenize bpf_csum_diff helper for all archs and also
     add a batch of new BPF selftests for it.

   - Extend netkit with an option to delegate skb->{mark,priority}
     scrubbing to its BPF program.

   - Make the bpf_get_netns_cookie() helper available also to tc(x) BPF
     programs.

  Protocols:

   - Introduces 4-tuple hash for connected udp sockets, speeding-up
     significantly connected sockets lookup.

   - Add a fastpath for some TCP timers that usually expires after
     close, the socket lock contention.

   - Add inbound and outbound xfrm state caches to speed up state
     lookups.

   - Avoid sending MPTCP advertisements on stale subflows, reducing
     risks on loosing them.

   - Make neighbours table flushing more scalable, maintaining per
     device neigh lists.

  Driver API:

   - Introduce a unified interface to configure transmission H/W
     shaping, and expose it to user-space via generic-netlink.

   - Add support for per-NAPI config via netlink. This makes napi
     configuration persistent across queues removal and re-creation.
     Requires driver updates, currently supported drivers are:
     nVidia/Mellanox mlx4 and mlx5, Broadcom brcm and Intel ice.

   - Add ethtool support for writing SFP / PHY firmware blocks.

   - Track RSS context allocation from ethtool core.

   - Implement support for mirroring to DSA CPU port, via TC mirror
     offload.

   - Consolidate FDB updates notification, to avoid duplicates on
     device-specific entries.

   - Expose DPLL clock quality level to the user-space.

   - Support master-slave PHY config via device tree.

  Tests and tooling:

   - forwarding: introduce deferred commands, to simplify the cleanup
     phase

  Drivers:

   - Updated several drivers - Amazon vNic, Google vNic, Microsoft vNic,
     Intel e1000e and Broadcom Tigon3 - to use netdev-genl to link the
     IRQs and queues to NAPI IDs, allowing busy polling and better
     introspection.

   - Ethernet high-speed NICs:
      - nVidia/Mellanox:
         - mlx5:
           - a large refactor to implement support for cross E-Switch
             scheduling
           - refactor H/W conter management to let it scale better
           - H/W GRO cleanups
      - Intel (100G, ice)::
         - add support for ethtool reset
         - implement support for per TX queue H/W shaping
      - AMD/Solarflare:
         - implement per device queue stats support
      - Broadcom (bnxt):
         - improve wildcard l4proto on IPv4/IPv6 ntuple rules
      - Marvell Octeon:
         - Add representor support for each Resource Virtualization Unit
           (RVU) device.
      - Hisilicon:
         - add support for the BMC Gigabit Ethernet
      - IBM (EMAC):
         - driver cleanup and modernization
      - Cisco (VIC):
         - raise the queues number limit to 256

   - Ethernet virtual:
      - Google vNIC:
         - implement page pool support
      - macsec:
         - inherit lower device's features and TSO limits when
           offloading
      - virtio_net:
         - enable premapped mode by default
         - support for XDP socket(AF_XDP) zerocopy TX
      - wireguard:
         - set the TSO max size to be GSO_MAX_SIZE, to aggregate larger
           packets.

   - Ethernet NICs embedded and virtual:
      - Broadcom ASP:
         - enable software timestamping
      - Freescale:
         - add enetc4 PF driver
      - MediaTek: Airoha SoC:
         - implement BQL support
      - RealTek r8169:
         - enable TSO by default on r8168/r8125
         - implement extended ethtool stats
      - Renesas AVB:
         - enable TX checksum offload
      - Synopsys (stmmac):
         - support header splitting for vlan tagged packets
         - move common code for DWMAC4 and DWXGMAC into a separate FPE
           module.
         - add dwmac driver support for T-HEAD TH1520 SoC
      - Synopsys (xpcs):
         - driver refactor and cleanup
      - TI:
         - icssg_prueth: add VLAN offload support
      - Xilinx emaclite:
         - add clock support

   - Ethernet switches:
      - Microchip:
         - implement support for the lan969x Ethernet switch family
         - add LAN9646 switch support to KSZ DSA driver

   - Ethernet PHYs:
      - Marvel: 88q2x: enable auto negotiation
      - Microchip: add support for LAN865X Rev B1 and LAN867X Rev C1/C2

   - PTP:
      - Add support for the Amazon virtual clock device
      - Add PtP driver for s390 clocks

   - WiFi:
      - mac80211
         - EHT 1024 aggregation size for transmissions
         - new operation to indicate that a new interface is to be added
         - support radio separation of multi-band devices
         - move wireless extension spy implementation to libiw
      - Broadcom:
         - brcmfmac: optional LPO clock support
      - Microchip:
         - add support for Atmel WILC3000
      - Qualcomm (ath12k):
         - firmware coredump collection support
         - add debugfs support for a multitude of statistics
      - Qualcomm (ath5k):
         -  Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
      - Realtek:
         - rtw88: 8821au and 8812au USB adapters support
         - rtw89: add thermal protection
         - rtw89: fine tune BT-coexsitence to improve user experience
         - rtw89: firmware secure boot for WiFi 6 chip

   - Bluetooth
      - add Qualcomm WCN785x support for ids Foxconn 0xe0fc/0xe0f3 and
        0x13d3:0x3623
      - add Realtek RTL8852BE support for id Foxconn 0xe123
      - add MediaTek MT7920 support for wireless module ids
      - btintel_pcie: add handshake between driver and firmware
      - btintel_pcie: add recovery mechanism
      - btnxpuart: add GPIO support to power save feature"

* tag 'net-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1475 commits)
  mm: page_frag: fix a compile error when kernel is not compiled
  Documentation: tipc: fix formatting issue in tipc.rst
  selftests: nic_performance: Add selftest for performance of NIC driver
  selftests: nic_link_layer: Add selftest case for speed and duplex states
  selftests: nic_link_layer: Add link layer selftest for NIC driver
  bnxt_en: Add FW trace coredump segments to the coredump
  bnxt_en: Add a new ethtool -W dump flag
  bnxt_en: Add 2 parameters to bnxt_fill_coredump_seg_hdr()
  bnxt_en: Add functions to copy host context memory
  bnxt_en: Do not free FW log context memory
  bnxt_en: Manage the FW trace context memory
  bnxt_en: Allocate backing store memory for FW trace logs
  bnxt_en: Add a 'force' parameter to bnxt_free_ctx_mem()
  bnxt_en: Refactor bnxt_free_ctx_mem()
  bnxt_en: Add mem_valid bit to struct bnxt_ctx_mem_type
  bnxt_en: Update firmware interface spec to 1.10.3.85
  selftests/bpf: Add some tests with sockmap SK_PASS
  bpf: fix recursive lock when verdict program return SK_PASS
  wireguard: device: support big tcp GSO
  wireguard: selftests: load nf_conntrack if not present
  ...

3 months agoMerge tag 'bpf-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf...
Linus Torvalds [Thu, 21 Nov 2024 16:11:04 +0000 (08:11 -0800)]
Merge tag 'bpf-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next

Pull bpf updates from Alexei Starovoitov:

 - Add BPF uprobe session support (Jiri Olsa)

 - Optimize uprobe performance (Andrii Nakryiko)

 - Add bpf_fastcall support to helpers and kfuncs (Eduard Zingerman)

 - Avoid calling free_htab_elem() under hash map bucket lock (Hou Tao)

 - Prevent tailcall infinite loop caused by freplace (Leon Hwang)

 - Mark raw_tracepoint arguments as nullable (Kumar Kartikeya Dwivedi)

 - Introduce uptr support in the task local storage map (Martin KaFai
   Lau)

 - Stringify errno log messages in libbpf (Mykyta Yatsenko)

 - Add kmem_cache BPF iterator for perf's lock profiling (Namhyung Kim)

 - Support BPF objects of either endianness in libbpf (Tony Ambardar)

 - Add ksym to struct_ops trampoline to fix stack trace (Xu Kuohai)

 - Introduce private stack for eligible BPF programs (Yonghong Song)

 - Migrate samples/bpf tests to selftests/bpf test_progs (Daniel T. Lee)

 - Migrate test_sock to selftests/bpf test_progs (Jordan Rife)

* tag 'bpf-next-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (152 commits)
  libbpf: Change hash_combine parameters from long to unsigned long
  selftests/bpf: Fix build error with llvm 19
  libbpf: Fix memory leak in bpf_program__attach_uprobe_multi
  bpf: use common instruction history across all states
  bpf: Add necessary migrate_disable to range_tree.
  bpf: Do not alloc arena on unsupported arches
  selftests/bpf: Set test path for token/obj_priv_implicit_token_envvar
  selftests/bpf: Add a test for arena range tree algorithm
  bpf: Introduce range_tree data structure and use it in bpf arena
  samples/bpf: Remove unused variable in xdp2skb_meta_kern.c
  samples/bpf: Remove unused variables in tc_l2_redirect_kern.c
  bpftool: Cast variable `var` to long long
  bpf, x86: Propagate tailcall info only for subprogs
  bpf: Add kernel symbol for struct_ops trampoline
  bpf: Use function pointers count as struct_ops links count
  bpf: Remove unused member rcu from bpf_struct_ops_map
  selftests/bpf: Add struct_ops prog private stack tests
  bpf: Support private stack for struct_ops progs
  selftests/bpf: Add tracing prog private stack tests
  bpf, x86: Support private stack in jit
  ...

3 months agoMerge tag 'nand/for-6.13' into mtd/next
Miquel Raynal [Thu, 21 Nov 2024 16:04:19 +0000 (17:04 +0100)]
Merge tag 'nand/for-6.13' into mtd/next

SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.

Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.

3 months agoMerge tag 'soc-arm-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Linus Torvalds [Wed, 20 Nov 2024 23:47:22 +0000 (15:47 -0800)]
Merge tag 'soc-arm-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC updates from Arnd Bergmann:
 "The SoC specific code updates for 6.13 are fairly minimal.

  One Broadcom SoC model gains automatic configuration for the debug
  uarg as we have on many other machines, the remaining changes are
  trivial cleanups"

* tag 'soc-arm-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: imx: Switch to new sys-off handler API
  ARM: bcm: brcmstb: Drop custom init_irq callback
  ARM: bcm: Support BCMBCA debug UART
  ARM: zynq: Remove unused zynq_slcr_init() declaration
  ASoC: samsung: Remove obsoleted declaration for s3c64xx_ac97_setup_gpio
  ARM: samsung: Remove obsoleted declaration for s3c_hwmon_set_platdata

3 months agoMerge tag 'soc-defconfig-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Linus Torvalds [Wed, 20 Nov 2024 23:44:56 +0000 (15:44 -0800)]
Merge tag 'soc-defconfig-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC defconfig updates from Arnd Bergmann:
 "As usual, a few newly added device drivers get enabled in the arm32
  multi_v7_defconfig and arm64 defconfig as well as a few of the SoC
  specific config files.

  The main visible change is the inclusion of (reduced) debug info by
  default in the 32-bit defconfig"

* tag 'soc-defconfig-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: imx_v6_v7_defconfig: Enable drivers for Kobo Clara 2E
  arm64: defconfig: Enable VBATTB clock and Renesas RTCA-3
  arm64: defconfig: Enable PCF857X GPIO expander
  arm64: defconfig: Enable sc7280 clock controllers
  ARM: configs: at91: enable PAC1934 driver as module
  ARM: multi_v7_defconfig: Enable debugging symbols by default

3 months agoMerge tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Linus Torvalds [Wed, 20 Nov 2024 23:40:54 +0000 (15:40 -0800)]
Merge tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC driver updates from Arnd Bergmann:
 "Nothing particular important in the SoC driver updates, just the usual
  improvements to for drivers/soc and a couple of subsystems that don't
  fit anywhere else:

   - The largest set of updates is for Qualcomm SoC drivers, extending
     the set of supported features for additional SoCs in the QSEECOM,
     LLCC and socinfo drivers.a

   - The ti_sci firmware driver gains support for power managment

   - The drivers/reset subsystem sees a rework of the microchip sparx5
     and amlogic reset drivers to support additional chips, plus a few
     minor updates on other platforms

   - The SCMI firmware interface driver gains support for two protocol
     extensions, allowing more flexible use of the shared memory area
     and new DT binding properties for configurability.

   - Mediatek SoC drivers gain support for power managment on the MT8188
     SoC and a new driver for DVFS.

   - The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
     and a few bugfixes

   - The Hisilicon Kunpeng HCCS driver gains support for configuring
     lanes through sysfs

  Finally, there are cleanups and minor fixes for drivers/{soc, bus,
  memory}, including changing back the .remove_new callback to .remove,
  as well as a few other updates for freescale (powerpc) soc drivers,
  NXP i.MX soc drivers, cznic turris platform driver, memory controller
  drviers, TI OMAP SoC drivers, and Tegra firmware drivers"

* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
  soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
  soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
  soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
  platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
  platform: cznic: turris-omnia-mcu: Document the driver private data structure
  firmware: turris-mox-rwtm: Document the driver private data structure
  bus: Switch back to struct platform_driver::remove()
  soc: qcom: ice: Remove the device_link field in qcom_ice
  drm/msm/adreno: Setup SMMU aparture for per-process page table
  firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
  firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
  soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
  dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
  soc: qcom: llcc: Flip the manual slice configuration condition
  dt-bindings: firmware: qcom,scm: Document sm8750 SCM
  firmware: qcom: uefisecapp: Allow X1E Devkit devices
  misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
  misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
  soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
  dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
  ...

3 months agoMerge tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Linus Torvalds [Wed, 20 Nov 2024 23:26:46 +0000 (15:26 -0800)]
Merge tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull SoC devicetree updates from Arnd Bergmann:
 "This release adds the devicetree files for an impressive number of new
  SoC variants, though as expected these are all related to others we
  already support:

   - The microchip sam9x7 devicetree is now added, after the device
     driver and platform code has already made it in. This is likely the
     last ARMv5 (!) platform to ever get added, updating the 20+ year
     old at91/sam9 platform with DDR3 memory and gigabit ethernet.

   - On the Apple platform, there are now devicetree files for a number
     of A-series SoCs in addition to the M-series ones, these are used
     primarily in phones and tablets, but are closely related to the
     already supported chips.

   - Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in
     older Samsung Galaxy phones.

   - Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely
     related to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end
     laptops.

   - Rockchip RK3528 and RK3576 are new variants of their TV box and
     Tablet chips, still using the older ARMv8.0 cores from
     RK3328/RK3399 but with a newer process and other improvements from
     the RK35xx (otherwise ARMv8.2) chips. RK3566T and RK3399-S are also
     added, these are just lower-cost versions of their normal
     counterparts.

   - TI J742S2 is a feature-reduced version of the J784s4
     industrial/automotive SoC, with fewer CPU cores.

   - Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
     (Cortex-A53) core, at this point support is only added for running
     on the RISC-V side on the LicheeRV Nano board.

  A total of 92 new .dts files describing individual machines is added,
  which must be a new record. The majority of these is for the newly
  added chips above, notably all the Apple phones and tablets. The other
  new machines include nine industrial/embedded boards with NXP i.MX6 or
  i.MX8 SoCs, eight for Rockchips RK35XX and one or two each for
  Rockchips RV1109, RK3308, Allwinner A33, Tegra 234, Qualcomm
  qcs9100/sc8280xp/x1e80100, TI AM625 and Starfive JH7110.

  As usual there are also many newly added features in existing boards
  as well as cleanups and minor bugfixes"

* tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (718 commits)
  arm64: dts: apm: Remove unused and undocumented "bus_num" property
  arm: dts: spear13xx: Remove unused and undocumented "pl022,slave-tx-disable" property
  arm64: dts: amd: Remove unused and undocumented "amd,zlib-support" property
  arm64: dts: lg131x: Update spi clock properties
  arm64: dts: seattle: Update spi clock properties
  arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
  arm64: dts: rockchip: add Radxa ROCK 5C
  dt-bindings: arm: rockchip: add Radxa ROCK 5C
  arm64: dts: rockchip: orangepi-5-plus: Enable GPU
  arm64: dts: rockchip: enable USB3 on NanoPC-T6
  arm64: dts: rockchip: adapt regulator nodenames to preferred form
  arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
  arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
  arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
  arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
  arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
  arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
  arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
  arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
  arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
  ...

3 months agoMerge tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd...
Linus Torvalds [Wed, 20 Nov 2024 23:13:02 +0000 (15:13 -0800)]
Merge tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic

Pull asm-generic updates from Arnd Bergmann:
 "These are a number of unrelated cleanups, generally simplifying the
  architecture specific header files:

   - A series from Al Viro simplifies asm/vga.h, after it turns out that
     most of it can be generalized.

   - A series from Julian Vetter adds a common version of
     memcpy_{to,from}io() and memset_io() and changes most architectures
     to use that instead of their own implementation

   - A series from Niklas Schnelle concludes his work to make PC style
     inb()/outb() optional

   - Nicolas Pitre contributes improvements for the generic do_div()
     helper

   - Christoph Hellwig adds a generic version of page_to_phys() and
     phys_to_page(), replacing the slightly different architecture
     specific definitions.

   - Uwe Kleine-Koenig has a minor cleanup for ioctl definitions"

* tag 'asm-generic-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
  empty include/asm-generic/vga.h
  sparc: get rid of asm/vga.h
  asm/vga.h: don't bother with scr_mem{cpy,move}v() unless we need to
  vt_buffer.h: get rid of dead code in default scr_...() instances
  tty: serial: export serial_8250_warn_need_ioport
  lib/iomem_copy: fix kerneldoc format style
  hexagon: simplify asm/io.h for !HAS_IOPORT
  loongarch: Use new fallback IO memcpy/memset
  csky: Use new fallback IO memcpy/memset
  arm64: Use new fallback IO memcpy/memset
  New implementation for IO memcpy and IO memset
  watchdog: Add HAS_IOPORT dependency for SBC8360 and SBC7240
  __arch_xprod64(): make __always_inline when optimizing for performance
  ARM: div64: improve __arch_xprod_64()
  asm-generic/div64: optimize/simplify __div64_const32()
  lib/math/test_div64: add some edge cases relevant to __div64_const32()
  asm-generic: add an optional pfn_valid check to page_to_phys
  asm-generic: provide generic page_to_phys and phys_to_page implementations
  asm-generic/io.h: Remove I/O port accessors for HAS_IOPORT=n
  tty: serial: handle HAS_IOPORT dependencies
  ...

3 months agoMerge tag 'for-linus' of https://github.com/openrisc/linux
Linus Torvalds [Wed, 20 Nov 2024 22:56:02 +0000 (14:56 -0800)]
Merge tag 'for-linus' of https://github.com/openrisc/linux

Pull OpenRISC update from Stafford Horne:
 "A single fixup from me: Fix bug with earlycon being broken due to
  removal of early_ioremap"

* tag 'for-linus' of https://github.com/openrisc/linux:
  openrisc: Implement fixmap to fix earlycon

3 months agoMerge tag 'microblaze-v6.13' of git://git.monstr.eu/linux-2.6-microblaze
Linus Torvalds [Wed, 20 Nov 2024 22:54:05 +0000 (14:54 -0800)]
Merge tag 'microblaze-v6.13' of git://git.monstr.eu/linux-2.6-microblaze

Pull microblaze updates from Michal Simek:

 - Export xmb_manager functions

 - Remove empty #ifndef __ASSEMBLY__ statement

 - Use str_yes_no() helper in show_cpuinfo()

* tag 'microblaze-v6.13' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: mb: Use str_yes_no() helper in show_cpuinfo()
  microblaze: Remove empty #ifndef __ASSEMBLY__ statement
  microblaze: Export xmb_manager functions

3 months agoMerge tag 'ipe-pr-20241119' of git://git.kernel.org/pub/scm/linux/kernel/git/wufan/ipe
Linus Torvalds [Wed, 20 Nov 2024 22:51:08 +0000 (14:51 -0800)]
Merge tag 'ipe-pr-20241119' of git://git.kernel.org/pub/scm/linux/kernel/git/wufan/ipe

Pull IPE update from Fan Wu:
 "One commit from Colin Ian King, which removes unnecessary error
  handling code in the IPE boot policy generation helper program"

* tag 'ipe-pr-20241119' of git://git.kernel.org/pub/scm/linux/kernel/git/wufan/ipe:
  scripts: ipe: polgen: remove redundant close and error exit path

3 months agoMerge tag 'seccomp-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees...
Linus Torvalds [Wed, 20 Nov 2024 22:36:28 +0000 (14:36 -0800)]
Merge tag 'seccomp-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux

Pull seccomp update from Kees Cook:

 - Provide stub for !HAVE_ARCH_SECCOMP_FILTER (Linus Walleij)

   This will make it easier to port arm32 to the generic entry code.

* tag 'seccomp-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  seccomp: Stub for !HAVE_ARCH_SECCOMP_FILTER

3 months agoMerge tag 'efi-next-for-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Linus Torvalds [Wed, 20 Nov 2024 22:13:28 +0000 (14:13 -0800)]
Merge tag 'efi-next-for-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi

Pull EFI updates from Ard Biesheuvel:
 "Just some cleanups and bug fixes this time around:

   - Align handling of the compiled-in command line with the core kernel

   - Measure the initrd into the TPM also when it was loaded via the EFI
     file I/O protocols

   - Clean up TPM event log handling

   - Sanity check the EFI memory attributes table, and apply it after
     kexec too

   - Assorted other fixes"

* tag 'efi-next-for-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi: Fix memory leak in efivar_ssdt_load
  efi/libstub: Take command line overrides into account for loaded files
  efi/libstub: Fix command line fallback handling when loading files
  efi/libstub: Parse builtin command line after bootloader provided one
  x86/efi: Apply EFI Memory Attributes after kexec
  x86/efi: Drop support for the EFI_PROPERTIES_TABLE
  efi/memattr: Ignore table if the size is clearly bogus
  efi/zboot: Fix outdated comment about using LoadImage/StartImage
  efi/libstub: Free correct pointer on failure
  libstub,tpm: do not ignore failure case when reading final event log
  tpm: fix unsigned/signed mismatch errors related to __calc_tpm2_event_size
  tpm: do not ignore memblock_reserve return value
  tpm: fix signed/unsigned bug when checking event logs
  efi/libstub: measure initrd to PCR9 independent of source
  efi/libstub: remove unnecessary cmd_line_len from efi_convert_cmdline()
  efi/libstub: fix efi_parse_options() ignoring the default command line

3 months agoMerge tag 'platform-drivers-x86-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 20 Nov 2024 22:07:55 +0000 (14:07 -0800)]
Merge tag 'platform-drivers-x86-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver updates from Ilpo Järvinen:

 - alienware WMAX thermal interface support

 - Split ACPI and platform device based amd/hsmp drivers

 - AMD X3D frequency/cache mode switching support

 - asus thermal policy fixes

 - Disable C1 auto-demotion in suspend to allow entering the deepest
   C-states

 - Fix volume buttons on Thinkpad X12 Detachable Tablet Gen 1

 - Replace intel_scu_ipc "workaround" with 32-bit IO

 - Correct *_show() function error handling in panasonic-laptop

 - Gemini Lake P2SB devfn correction

 - think-lmi Admin/System certificate authentication support

 - Disable WMI devices for shutdown, refactoring continues

 - Vexia EDU ATLA 10 tablet support

 - Surface Pro 9 5G (Arm/QCOM) support

 - Misc cleanups / refactoring / improvements

* tag 'platform-drivers-x86-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (69 commits)
  platform/x86: p2sb: Cache correct PCI bar for P2SB on Gemini Lake
  platform/x86: panasonic-laptop: Return errno correctly in show callback
  Documentation: alienware-wmi: Describe THERMAL_INFORMATION operation 0x02
  alienware-wmi: create_thermal_profile() no longer brute-forces IDs
  alienware-wmi: Adds support to Alienware x17 R2
  alienware-wmi: extends the list of supported models
  alienware-wmi: order alienware_quirks[] alphabetically
  platform/x86/intel/pmt: allow user offset for PMT callbacks
  platform/x86/amd/hsmp: Change the error type
  platform/x86/amd/hsmp: Add new error code and error logs
  platform/x86/amd: amd_3d_vcache: Add sysfs ABI documentation
  platform/x86/amd: amd_3d_vcache: Add AMD 3D V-Cache optimizer driver
  intel-hid: fix volume buttons on Thinkpad X12 Detachable Tablet Gen 1
  platform/x86/amd/hsmp: mark hsmp_msg_desc_table[] as maybe_unused
  platform/x86: asus-wmi: Use platform_profile_cycle()
  platform/x86: asus-wmi: Fix inconsistent use of thermal policies
  platform/x86: hp: hp-bioscfg: remove redundant if statement
  MAINTAINERS: Update ISHTP ECLITE maintainer entry
  platform/x86: x86-android-tablets: Add support for Vexia EDU ATLA 10 tablet
  platform/x86: x86-android-tablets: Add support for getting i2c_adapter by PCI parent devname()
  ...

3 months agoMerge tag 'media/v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab...
Linus Torvalds [Wed, 20 Nov 2024 22:05:34 +0000 (14:05 -0800)]
Merge tag 'media/v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull media fix from Mauro Carvalho Chehab:

 - uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in
   uvc_parse_format

* tag 'media/v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in uvc_parse_format

3 months agoMerge tag 'media/v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab...
Linus Torvalds [Wed, 20 Nov 2024 22:01:15 +0000 (14:01 -0800)]
Merge tag 'media/v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media

Pull media updates from Mauro Carvalho Chehab:

 - removal of the old omap4iss media driver

 - mantis: remove orphan mantis_core.h

 - add support for Raspberypi CFE

 - uvc driver got a co-maintainer

 - main media tree moved to git://linuxtv.org/media.git

 - lots of driver cleanups, updates and fixes

* tag 'media/v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (233 commits)
  docs: media: update location of the media patches
  MAINTAINERS: update location of media main tree
  media: MAINTAINERS: Add Hans de Goede as USB VIDEO CLASS co-maintainer
  media: platform: samsung: s5p-jpeg: Remove deadcode
  media: qcom: camss: Add MSM8953 resources
  media: dt-bindings: Add qcom,msm8953-camss
  media: qcom: camss: implement pm domain ops for VFE v4.1
  media: platform: exynos4-is: Fix an OF node reference leak in fimc_md_is_isp_available
  media: adv7180: Also check for "adi,force-bt656-4"
  media: dt-bindings: adv7180: Document 'adi,force-bt656-4'
  media: mgb4: Fix inconsistent input/output alignment in loopback mode
  media: replace obsolete [email protected] alias
  Documentation: media: improve V4L2_CID_MIN_BUFFERS_FOR_*, doc
  media: vicodec: add V4L2_CID_MIN_BUFFERS_FOR_* controls
  media: atomisp: Add check for rgby_data memory allocation failure
  media: atomisp: remove redundant re-checking of err
  media: atomisp: Fix spelling errors reported by codespell
  media: atomisp: Remove License information boilerplate
  media: atomisp: Fix typos in comment
  media: atomisp: hmm_bo: Fix spelling errors in hmm_bo.h
  ...

3 months agoMerge tag 'hid-for-linus-2024111801' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 20 Nov 2024 21:57:40 +0000 (13:57 -0800)]
Merge tag 'hid-for-linus-2024111801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid

Pull HID updates from Jiri Kosina:

 - improvement in the way hid-bpf coexists with specific drivers (others
   than hid-generic) that are already bound to devices (Benjamin
   Tissoires)

 - removal of three way-too-aggressive BUG_ON()s from HID drivers (He
   Lugang)

 - assorted cleanups and small code fixes to HID core (Dmitry Torokhov,
   Yan Zhen, Nathan Chancellor, Andy Shevchenko)

 - support for Corsair Void headset family (Stuart Hayhurst)

 - Support for Goodix GT7986U SPI (Charles Wang)

 - initial vendor-specific driver for Kysona, currently adding support
   for Kysona M600 (Lode Willems)

 - other assorted code cleanups and small bugfixes all over the place

* tag 'hid-for-linus-2024111801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (40 commits)
  HID: multitouch: make mt_set_mode() less cryptic
  HID: hid-goodix-spi: Add OF supports
  dt-bindings: input: Goodix GT7986U SPI HID Touchscreen
  HID: hyperv: streamline driver probe to avoid devres issues
  HID: magicmouse: Apple Magic Trackpad 2 USB-C driver support
  HID: rmi: Add select RMI4_F3A in Kconfig
  HID: wacom: Interpret tilt data from Intuos Pro BT as signed values
  HID: steelseries: Add capacity_level mapping
  HID: steelseries: Fix battery requests stopping after some time
  HID: hid-goodix: Fix HID get/set feature operation overwritten problem
  HID: hid-goodix: Return 0 when receiving an empty HID feature package
  HID: bpf: drop use of Logical|Physical|UsageRange
  HID: bpf: Fix Rapoo M50 Plus Silent side buttons
  HID: bpf: Fix NKRO on Mistel MD770
  HID: replace BUG_ON() with WARN_ON()
  HID: wacom: Set eraser status when either 'Eraser' or 'Invert' usage is set
  HID: Kysona: add basic online status
  HID: Kysona: check battery status every 5s using a workqueue
  HID: Kysona: Add basic battery reporting for Kysona M600
  HID: Add IDs for Kysona
  ...

3 months agoMerge tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Wed, 20 Nov 2024 21:19:25 +0000 (13:19 -0800)]
Merge tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull devicetree updates from Rob Herring:
 "Bindings:

   - Enable dtc "interrupt_provider" warnings for binding examples. Fix
     the warnings in fsl,mu-msi and ti,sci-inta due to this.

   - Convert zii,rave-sp-wdt, zii,rave-sp-pwrbutton, and
     altr,fpga-passive-serial to DT schema format

   - Add some documentation on the different forms of YAML text blocks
     which are a constant source of review comments

   - Fix some schema errors in constraints for arrays

   - Add compatibles for qcom,sar2130p-pdc and onnn,adt7462

  DT core:

   - Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n

   - Add some warnings on deprecated address handling

   - Rework early_init_dt_scan() so the arch can pass in the phys
     address of the DTB as __pa() is not always valid to use. This fixes
     a warning for arm64 with kexec.

   - Add and use some new DT graph iterators for iterating over ports
     and endpoints

   - Rework reserved-memory handling to be sized dynamically for fixed
     regions

   - Optimize of_modalias() to avoid a strlen() call

   - Constify struct device_node and property pointers where ever
     possible"

* tag 'devicetree-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (36 commits)
  of: Allow overlay kunit tests to run CONFIG_OF_OVERLAY=n
  dt-bindings: interrupt-controller: qcom,pdc: Add SAR2130P compatible
  of/address: Rework bus matching to avoid warnings
  of: WARN on deprecated #address-cells/#size-cells handling
  of/fdt: Don't use default address cell sizes for address translation
  dt-bindings: Enable dtc "interrupt_provider" warnings
  of/fdt: add dt_phys arg to early_init_dt_scan and early_init_dt_verify
  dt-bindings: cache: qcom,llcc: Fix X1E80100 reg entries
  dt-bindings: watchdog: convert zii,rave-sp-wdt.txt to yaml format
  dt-bindings: input: convert zii,rave-sp-pwrbutton.txt to yaml
  media: xilinx-tpg: use new of_graph functions
  fbdev: omapfb: use new of_graph functions
  gpu: drm: omapdrm: use new of_graph functions
  ASoC: audio-graph-card2: use new of_graph functions
  ASoC: audio-graph-card: use new of_graph functions
  ASoC: test-component: use new of_graph functions
  of: property: use new of_graph functions
  of: property: add of_graph_get_next_port_endpoint()
  of: property: add of_graph_get_next_port()
  of: module: remove strlen() call in of_modalias()
  ...

3 months agoMerge tag 'auxdisplay-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy...
Linus Torvalds [Wed, 20 Nov 2024 20:55:41 +0000 (12:55 -0800)]
Merge tag 'auxdisplay-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-auxdisplay

Pull auxdisplay update from Andy Shevchenko:

 - Move Holtek 16k33 driver to use agnostic i2c_get_match_data()

 - Miscellaneuous cleanups

* tag 'auxdisplay-v6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-auxdisplay:
  auxdisplay: Remove unused functions
  auxdisplay: ht16k33: Make use of i2c_get_match_data()
  auxdisplay: Drop explicit initialization of struct i2c_device_id::driver_data to 0

3 months agoMerge tag 'mmc-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Linus Torvalds [Wed, 20 Nov 2024 20:51:32 +0000 (12:51 -0800)]
Merge tag 'mmc-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add support for Ultra Capacity SD cards (SDUC, 2TB to 128TB)
   - Add support for Ultra High-Speed II SD cards (UHS-II)
   - Use a reset control for pwrseq_simple
   - Add SD card quirk for broken poweroff notification
   - Use GFP_NOIO for SD ACMD22

  MMC host:
   - bcm2835: Introduce proper clock handling
   - mtk-sd: Add support for the Host-Software-Queue interface
   - mtk-sd: Add support for the mt7988/mt8196 variants
   - mtk-sd: Fix a couple of error paths in ->probe()
   - sdhci: Add interface to support UHS-II SD cards
   - sdhci_am654: Fixup support for changing the signal voltage level
   - sdhci-cadence: Add support for the Microchip PIC64GX variant
   - sdhci-esdhc-imx: Add support for eMMC HW-reset
   - sdhci-msm: Add support for the X1E80100/IPQ5424/SAR2130P/QCS615 variants
   - sdhci-of-arasan: Add support for eMMC HW-reset
   - sdhci-pci-gli: Add UHS-II support for the GL9767/GL9755 variants

  MEMSTICK:
   - A couple of minor updates"

* tag 'mmc-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (78 commits)
  mmc: pwrseq_simple: Handle !RESET_CONTROLLER properly
  mmc: mtk-sd: Fix MMC_CAP2_CRYPTO flag setting
  mmc: mtk-sd: Fix error handle of probe function
  mmc: core: Correction a warning caused by incorrect type in assignment for UHS-II
  mmc: sdhci-esdhc-imx: Update esdhc sysctl dtocv bitmask
  mmc: sdhci-esdhc-imx: Implement emmc hardware reset
  mmc: core: Correct type in variable assignment for UHS-II
  mmc: sdhci-uhs2: correction a warning caused by incorrect type in argument
  mmc: sdhci-uhs2: Remove unnecessary variables
  mmc: sdhci-uhs2: Correct incorrect type in argument
  mmc: sdhci: Make MMC_SDHCI_UHS2 config symbol invisible
  mmc: sdhci-uhs2: Remove unnecessary NULL check
  mmc: core: Fix error paths for UHS-II card init and re-init
  mmc: core: Add error handling of sd_uhs2_power_up()
  mmc: core: Simplify sd_uhs2_power_up()
  mmc: bcm2835: Introduce proper clock handling
  mmc: bcm2835: Fix type of current clock speed
  dt-bindings: mmc: Add sdhci compatible for QCS615
  mmc: core: Use GFP_NOIO in ACMD22
  dt-bindings: mmc: sdhci-msm: Add SAR2130P compatible
  ...

3 months agoMerge tag 'pmdomain-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh...
Linus Torvalds [Wed, 20 Nov 2024 20:44:59 +0000 (12:44 -0800)]
Merge tag 'pmdomain-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm

Pull pmdomain updates from Ulf Hansson:
"pmdomain core:
   - Set the required dev for a required OPP during genpd attach
   - Add support for required OPPs to dev_pm_domain_attach_list()

  pmdomain providers:
   - ti: Enable GENPD_FLAG_ACTIVE_WAKEUP flag for ti_sci PM domains
   - mediatek: Add support for MT6735 PM domains
   - mediatek: Use OF-specific regulator API to get power domain supply
   - qcom: Add support for the SM8750/SAR2130P/qcs615/qcs8300 rpmhpds

  pmdomain consumers:
   - Convert a couple of consumer drivers to
     *_pm_domain_attach|detach_list()

  opp core:
   - Rework and cleanup some code that manages required OPPs
   - Remove *_opp_attach|detach_genpd()"

* tag 'pmdomain-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (25 commits)
  pmdomain: qcom: rpmhpd: Add rpmhpd support for SM8750
  dt-bindings: power: qcom,rpmpd: document the SM8750 RPMh Power Domains
  pmdomain: imx: Use of_property_present() for non-boolean properties
  pmdomain: imx: gpcv2: replace dev_err() with dev_err_probe()
  pmdomain: ti-sci: Use scope based of_node_put() to simplify code.
  pmdomain: ti-sci: Add missing of_node_put() for args.np
  pmdomain: ti-sci: set the GENPD_FLAG_ACTIVE_WAKEUP flag for all PM domains
  pmdomain: mediatek: Add support for MT6735
  pmdomain: qcom: rpmhpd: add support for SAR2130P
  dt-bindings: power: Add binding for MediaTek MT6735 power controller
  dt-bindings: power: rpmpd: Add SAR2130P compatible
  OPP: Drop redundant *_opp_attach|detach_genpd()
  cpufreq: qcom-nvmem: Convert to dev_pm_domain_attach|detach_list()
  media: venus: Convert into devm_pm_domain_attach_list() for OPP PM domain
  drm/tegra: gr3d: Convert into devm_pm_domain_attach_list()
  OPP: Drop redundant code in _link_required_opps()
  pmdomain: core: Set the required dev for a required OPP during genpd attach
  pmdomain: core: Manage the default required OPP from a separate function
  PM: domains: Support required OPPs in dev_pm_domain_attach_list()
  OPP: Rework _set_required_devs() to manage a single device per call
  ...

3 months agoMerge tag 'pwrseq-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 20 Nov 2024 20:41:03 +0000 (12:41 -0800)]
Merge tag 'pwrseq-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull power sequencing updates from Bartosz Golaszewski:

 - extend support for the wcn6855 model in the pwrseq-qcom-wcn driver

 - make this driver depend on CONFIG_OF=y as it uses some very
   OF-specific interfaces and depends on phandle parsing

* tag 'pwrseq-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  power: sequencing: qcom-wcn: improve support for wcn6855
  power: sequencing: make the QCom PMU pwrseq driver depend on CONFIG_OF

3 months agoMerge tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 20 Nov 2024 20:37:06 +0000 (12:37 -0800)]
Merge tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
 "Three new drivers, support for some new models in existing ones and
  lots of various tweaks and improvements across the board (switching to
  using recommended APIs, code shrink and simplification, etc.).

  Also a new feature in the character device uAPI where we now notify
  the user-space about changes triggered by in-kernel users as well, not
  only when they were done by other user-space agents.

  Summary:

  GPIOLIB core:
   - use the new mem_is_zero() instead of memchr_inv(s, 0, n)
   - don't store debounce period twice needlessly
   - clean-up debugfs handling
   - remove leftover comments referring to no longer used spinlocks
   - unduplicate some operations like SRCU locks and initializing GPIO
     descriptors
   - constify the sysfs class struct
   - use lock guards in GPIO sysfs code
   - update GPIO uAPI internal flags all at once atomically for
     consistency with other places
   - modify the behavior of the sysfs interface by no longer exporting
     lines that are named inside the driver code or board files with the
     sysfs links bearing the line names as this has for many years been
     largely unused due to the prevalence of DT, ACPI and firmware nodes
     over board files and made the API inconsistent
   - for GPIO interrupt providers: free irqs that are still requested by
     users when removing the chip

  GPIO uAPI:
   - notify user-space about changes to GPIO lines' state (requested,
     released, reconfigured) triggered from the kernel as well (until
     now we'd only do this for changes triggered from user-space)
   - to that end: modify the internal workings of the notification
     mechanism by switching to an atomic notifier which allows us to
     send events from atomic context
   - also to that end store the debounce period in the GPIO descriptor
     struct and not in the character device context struct
   - while at it, also cover the corner-case of users introducing
     changes over sysfs while others watch them via the character device
   - don't report GPIO lines requested as interrupts as "used" to
     user-space as it can still request them as GPIOs

  New drivers:
   - GPIO part of the MFD Congatec Board Controller
   - PolarFire GPIO controller
   - GPIOs on FTDI FT2232H

  Driver improvements:
   - use generic device property accessors instead of OF-specific ones
     across many GPIO drivers (mpc8xxx, vf610, eic-sprd, davinci,
     ts4900, xilinx, mvebu)
   - use devres helpers to simplify error paths and either shrink or
     entirely remove the driver's remove() callback (grgpio, amdpt,
     menz127, max730x, ftgpio010, 74x164, ljca)
   - use helper variables to store the address of pdev->dev and avoid
     some line-breaks
   - use device_for_each_child_node_scoped() to avoid having to put the
     fwnode on breaks or errors (gpio-sim, gpio-dwapb, gpiolib-acpi)
   - use a scoped bitmap to simplify the code and drop goto labels in
     gpio-aggregator
   - drop unneeded Kconfig dependencies on OF_GPIO (grgpio, mveby,
     xilinx)
   - add support for new models to gpio-aspeed, gpio-rockchip and
     gpio-dwapb
   - clean-up ACPI handling and some other bits in gpio-xgene-sb
   - replace deprecated PCI functions in pcie-idio-24 and pci-idio-16
   - allow to build davinci and mvebu drivers with COMPILE_TEST=y
   - remove dead code in gpio-mb86s7x
   - switch back to using platform_driver::remove() (after the
     conversion to remove_new()) across the GPIO drivers
   - remove remaining uses of GPIOF_ACTIVE_LOW across the tree and drop
     this deprecated symbol
   - convert the gpio-altera driver to no longer pull in the deprecated
     legacy-of-mm-gpiochip.h header
   - use of_property_present() instead of of_property_read_bool() in
     gpiolib-of and gpio-rockchip
   - allow to build the tegra186 driver on Tegra234 platforms in Kconfig

  Late fixes:
   - add a missing return value check after devm_kasprintf() to
     gpio-grgpio

  DT bindings:
   - document the ngpios property of gpio-mmio
   - add support for a new aspeed model
   - fix the example for st,nomadik-gpio

  Other:
   - kernel doc and comments tweaks
   - fix typos in TODO
   - reorder headers alphabetically in some drivers
   - fix incorrect format specifiers in gpio tools"

* tag 'gpio-updates-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (98 commits)
  gpio: tegra186: Allow to enable driver on Tegra234
  gpio: grgpio: Add NULL check in grgpio_probe
  tools: gpio: Fix several incorrect format specifiers
  gpio: mpfs: add CoreGPIO support
  gpio: rockchip: support new version GPIO
  gpio: rockchip: change the GPIO version judgment logic
  gpio: rockchip: explan the format of the GPIO version ID
  gpiolib: cdev: use !mem_is_zero() instead of memchr_inv(s, 0, n)
  MAINTAINERS: add gpio driver to PolarFire entry
  gpio: Get rid of GPIOF_ACTIVE_LOW
  USB: gadget: pxa27x_udc: Avoid using GPIOF_ACTIVE_LOW
  pcmcia: soc_common: Avoid using GPIOF_ACTIVE_LOW
  leds: gpio: Avoid using GPIOF_ACTIVE_LOW
  Input: gpio_keys_polled - avoid using GPIOF_ACTIVE_LOW
  Input: gpio_keys - avoid using GPIOF_ACTIVE_LOW
  gpio: Use of_property_present() for non-boolean properties
  gpio: mpfs: add polarfire soc gpio support
  gpio: altera: Drop legacy-of-mm-gpiochip.h header
  gpio: pcie-idio-24: Replace deprecated PCI functions
  gpio: pci-idio-16: Replace deprecated PCI functions
  ...

3 months agoMerge tag 'pwm/for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleine...
Linus Torvalds [Wed, 20 Nov 2024 20:34:22 +0000 (12:34 -0800)]
Merge tag 'pwm/for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux

Pull pwm updates from Uwe Kleine-König:
 "This contains a new abstraction for PWM waveforms that is more
  expressive that the legacy one. Compared to the old abstraction it
  contains a duty_offset member instead of polarity. This new
  abstraction is already used in an ADC driver merged into the iio tree.

  The new API requires changes to the lowlevel drivers. For now there
  are two drivers that are converted to the new API (axi-pwmgen and
  stm32). Converted drivers continue to work with the old API. Drivers
  not yet converted only work with the older API.

  Otherwise it's the usual collection of fixes, cleanups and dt doc
  updates.

  This time around thanks go to Andy Shevchenko, Clark Wang, Conor
  Dooley, David Lechner, Dimitri Fedrau, Frank Li, Jun Li, Kelvin Zhang,
  Krzysztof Kozlowski, Nuno Sa, Shen Lichuan and Trevor Gamblin for code
  contributions, testing and review"

* tag 'pwm/for-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
  pwm: Assume a disabled PWM to emit a constant inactive output
  pwm: core: export pwm_get_state_hw()
  pwm: core: use device_match_name() instead of strcmp(dev_name(...
  dt-bindings: pwm: adi,axi-pwmgen: Increase #pwm-cells to 3
  pwm: imx27: Use clk_bulk_*() API to simplify clock handling
  pwm: imx27: Workaround of the pwm output bug when decrease the duty cycle
  pwm: axi-pwmgen: Enable FORCE_ALIGN by default
  pwm: axi-pwmgen: Rename 0x10 register
  dt-bindings: pwm: amlogic: Document C3 PWM
  pwm: axi-pwmgen: Create a dedicated function for getting driver data from a chip
  pwm: atmel-tcb: Use min() macro
  pwm: stm32: Fix error checking for a regmap_read() call
  pwm: Add kernel doc for members added to pwm_ops recently
  pwm: Reorder symbols in core.c
  pwm: stm32: Implementation of the waveform callbacks
  pwm: axi-pwmgen: Implementation of the waveform callbacks
  pwm: Add tracing for waveform callbacks
  pwm: Provide new consumer API functions for waveforms
  pwm: New abstraction for PWM waveforms
  pwm: Add more locking

3 months agoMerge tag 'spi-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Linus Torvalds [Wed, 20 Nov 2024 20:23:06 +0000 (12:23 -0800)]
Merge tag 'spi-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "The only real core work we've got this time around is the completion
  of the transition to the new host/target naming for the core APIs,
  Kconfig still needs doing but that's a lot less invasive.

  Otherwise the big changes are the new drivers that have been added:

   - Completion of the conversion to spi_alloc_host()/_target() and
     removal of the old naming.

   - Cleanups for Rockchip drivers, these brought in a new logging
     helper in the driver core for warnings during probe.

   - Support for configuration of the word delay via spidev_test.

   - Support for AMD HID2 controllers, Apple SPI controller and Realtek
     SPI-NAND controllers"

* tag 'spi-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (58 commits)
  spi: imx: support word delay
  spi: imx: pass struct spi_transfer to prepare_transfer()
  spi: cs42l43: Add GPIO speaker id support to the bridge configuration
  spi: Delete useless checks
  spi: apple: Remove unnecessary .owner for apple_spi_driver
  spi: spidev_test: add support for word delay
  spi: apple: Add driver for Apple SPI controller
  spi: dt-bindings: apple,spi: Add binding for Apple SPI controllers
  spi: Use of_property_present() for non-boolean properties
  spi: zynqmp-gqspi: Undo runtime PM changes at driver exit time​
  spi: spi-mem: rtl-snand: Correctly handle DMA transfers
  spi: tegra210-quad: Avoid shift-out-of-bounds
  spi: axi-spi-engine: Emit trace events for spi transfers
  dt-bindings: spi: sprd,sc9860-spi: convert to YAML
  spi: Replace deprecated PCI functions
  spi: dt-bindings: samsung: Add a compatible for samsung,exynos8895-spi
  spi: spi-mem: Add Realtek SPI-NAND controller
  dt-bindings: spi: Add realtek,rtl9301-snand
  spi: make class structs const
  spi: dt-bindings: brcm,bcm2835-aux-spi: Convert to dtschema
  ...

3 months agoMerge tag 'regulator-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie...
Linus Torvalds [Wed, 20 Nov 2024 20:18:50 +0000 (12:18 -0800)]
Merge tag 'regulator-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "This was a quite quiet release for regulators on the drivers front,
  but we do have two small but useful core improvements:

   - Improve handling of cases where DT platforms specify both DT and
     init_data based configuration for a single regulator.

   - A helper of_regulator_get_optional() to simplify writing generic
     bindings for regulator consumers in subsystems.

  There's also some YAML conversions for the DT bindings which are a big
  part of the diffstat"

* tag 'regulator-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: dt-bindings: qcom,rpmh: Correct PM8550VE supplies
  regulator: Switch back to struct platform_driver::remove()
  regulator: doc: remove documentation comment for regulator_init
  regulator: doc: add missing documentation for init_cb
  regulator: rk808: Restrict DVS GPIOs to the RK808 variant only
  regulator: rk808: Use dev_err_probe() in the probe path
  regulator: rk808: Perform trivial code cleanups
  regulator: dt-bindings: qcom,qca6390-pmu: add more properties for wcn6855
  regulator: dt-bindings: lltc,ltc3676: convert to YAML
  regulator: core: Use fsleep() to get best sleep mechanism
  regulator: core: remove machine init callback from config
  regulator: core: add callback to perform runtime init
  regulator: core: do not silently ignore provided init_data
  regulator: max5970: Drop unused structs
  regulator: dt-bindings: vctrl-regulator: convert to YAML
  regulator: qcom-smd: make smd_vreg_rpm static
  regulator: Call of_node_put() only once in rzg2l_usb_vbus_regulator_probe()
  regulator: isl6271a: Drop explicit initialization of struct i2c_device_id::driver_data to 0
  regulator: Add devres version of of_regulator_get_optional()
  regulator: Add of_regulator_get_optional() for pure DT regulator lookup

3 months agoMerge tag 'regmap-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie...
Linus Torvalds [Wed, 20 Nov 2024 20:09:47 +0000 (12:09 -0800)]
Merge tag 'regmap-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap

Pull regmap updates from Mark Brown:
 "The main thing for regmap this time around is some improvements of the
  lockdep annotations which stop some false positives. We also have one
  new helper for setting a bitmask to the same value, and several test
  improvements"

* tag 'regmap-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: provide regmap_assign_bits()
  regmap: irq: Set lockdep class for hierarchical IRQ domains
  regmap: maple: Provide lockdep (sub)class for maple tree's internal lock
  regmap: kunit: Fix repeated test param
  regcache: Improve documentation of available cache types
  regmap: Specifically test writing 0 as a value to sparse caches
  regmap-irq: Consistently use memset32() in regmap_irq_thread()

3 months agoMerge tag 'linux_kselftest-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kerne...
Linus Torvalds [Wed, 20 Nov 2024 19:54:39 +0000 (11:54 -0800)]
Merge tag 'linux_kselftest-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest update from Shuah Khan:
 "timer test:
   - remove duplicate defines
   - fixes to improve error reporting

  rtc test:
   - check rtc alarm status in alarm test

  resctrl test:
   - add array overrun checks during iMC config parsing code and when
     reading strings
   - fixes and reorganizing code"

* tag 'linux_kselftest-next-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (23 commits)
  selftests/resctrl: Replace magic constants used as array size
  selftests/resctrl: Keep results from first test run
  selftests/resctrl: Do not compare performance counters and resctrl at low bandwidth
  selftests/resctrl: Use cache size to determine "fill_buf" buffer size
  selftests/resctrl: Ensure measurements skip initialization of default benchmark
  selftests/resctrl: Make benchmark parameter passing robust
  selftests/resctrl: Remove unused measurement code
  selftests/resctrl: Only support measured read operation
  selftests/resctrl: Remove "once" parameter required to be false
  selftests/resctrl: Make wraparound handling obvious
  selftests/resctrl: Protect against array overflow when reading strings
  selftests/resctrl: Protect against array overrun during iMC config parsing
  selftests/resctrl: Fix memory overflow due to unhandled wraparound
  selftests/resctrl: Print accurate buffer size as part of MBM results
  selftests/resctrl: Make functions only used in same file static
  selftests: Add a test mangling with uc_sigmask
  selftests: Rename sigaltstack to generic signal
  selftest: rtc: Add to check rtc alarm status for alarm related test
  selftests:timers: remove local CLOCKID defines
  selftests: timers: Remove unneeded semicolon
  ...

3 months agoMerge tag 'kgdb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt...
Linus Torvalds [Wed, 20 Nov 2024 19:47:43 +0000 (11:47 -0800)]
Merge tag 'kgdb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux

Pull kgdb updates from Daniel Thompson:
 "A relatively modest collection of changes:

   - Adopt kstrtoint() and kstrtol() instead of the simple_strtoXX
     family for better error checking of user input.

   - Align the print behavour when breakpoints are enabled and disabled
     by adopting the current behaviour of breakpoint disable for both.

   - Remove some of the (rather odd and user hostile) hex fallbacks and
     require kdb users to prefix with 0x instead.

   - Tidy up (and fix) control code handling in kdb's keyboard code.
     This makes the control code handling at the keyboard behave the
     same way as it does via the UART.

   - Switch my own entry in MAINTAINERS to my @kernel.org address"

* tag 'kgdb-6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
  kdb: fix ctrl+e/a/f/b/d/p/n broken in keyboard mode
  MAINTAINERS: Use Daniel Thompson's korg address for kgdb work
  kdb: Fix breakpoint enable to be silent if already enabled
  kdb: Remove fallback interpretation of arbitrary numbers as hex
  trace: kdb: Replace simple_strtoul with kstrtoul in kdb_ftdump
  kdb: Replace the use of simple_strto with safer kstrto in kdb_main

3 months agoMerge tag 'ftrace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux...
Linus Torvalds [Wed, 20 Nov 2024 19:34:10 +0000 (11:34 -0800)]
Merge tag 'ftrace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull ftrace updates from Steven Rostedt:

 - Restructure the function graph shadow stack to prepare it for use
   with kretprobes

   With the goal of merging the shadow stack logic of function graph and
   kretprobes, some more restructuring of the function shadow stack is
   required.

   Move out function graph specific fields from the fgraph
   infrastructure and store it on the new stack variables that can pass
   data from the entry callback to the exit callback.

   Hopefully, with this change, the merge of kretprobes to use fgraph
   shadow stacks will be ready by the next merge window.

 - Make shadow stack 4k instead of using PAGE_SIZE.

   Some architectures have very large PAGE_SIZE values which make its
   use for shadow stacks waste a lot of memory.

 - Give shadow stacks its own kmem cache.

   When function graph is started, every task on the system gets a
   shadow stack. In the future, shadow stacks may not be 4K in size.
   Have it have its own kmem cache so that whatever size it becomes will
   still be efficient in allocations.

 - Initialize profiler graph ops as it will be needed for new updates to
   fgraph

 - Convert to use guard(mutex) for several ftrace and fgraph functions

 - Add more comments and documentation

 - Show function return address in function graph tracer

   Add an option to show the caller of a function at each entry of the
   function graph tracer, similar to what the function tracer does.

 - Abstract out ftrace_regs from being used directly like pt_regs

   ftrace_regs was created to store a partial pt_regs. It holds only the
   registers and stack information to get to the function arguments and
   return values. On several archs, it is simply a wrapper around
   pt_regs. But some users would access ftrace_regs directly to get the
   pt_regs which will not work on all archs. Make ftrace_regs an
   abstract structure that requires all access to its fields be through
   accessor functions.

 - Show how long it takes to do function code modifications

   When code modification for function hooks happen, it always had the
   time recorded in how long it took to do the conversion. But this
   value was never exported. Recently the code was touched due to new
   ROX modification handling that caused a large slow down in doing the
   modifications and had a significant impact on boot times.

   Expose the timings in the dyn_ftrace_total_info file. This file was
   created a while ago to show information about memory usage and such
   to implement dynamic function tracing. It's also an appropriate file
   to store the timings of this modification as well. This will make it
   easier to see the impact of changes to code modification on boot up
   timings.

 - Other clean ups and small fixes

* tag 'ftrace-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (22 commits)
  ftrace: Show timings of how long nop patching took
  ftrace: Use guard to take ftrace_lock in ftrace_graph_set_hash()
  ftrace: Use guard to take the ftrace_lock in release_probe()
  ftrace: Use guard to lock ftrace_lock in cache_mod()
  ftrace: Use guard for match_records()
  fgraph: Use guard(mutex)(&ftrace_lock) for unregister_ftrace_graph()
  fgraph: Give ret_stack its own kmem cache
  fgraph: Separate size of ret_stack from PAGE_SIZE
  ftrace: Rename ftrace_regs_return_value to ftrace_regs_get_return_value
  selftests/ftrace: Fix check of return value in fgraph-retval.tc test
  ftrace: Use arch_ftrace_regs() for ftrace_regs_*() macros
  ftrace: Consolidate ftrace_regs accessor functions for archs using pt_regs
  ftrace: Make ftrace_regs abstract from direct use
  fgragh: No need to invoke the function call_filter_check_discard()
  fgraph: Simplify return address printing in function graph tracer
  function_graph: Remove unnecessary initialization in ftrace_graph_ret_addr()
  function_graph: Support recording and printing the function return address
  ftrace: Have calltime be saved in the fgraph storage
  ftrace: Use a running sleeptime instead of saving on shadow stack
  fgraph: Use fgraph data to store subtime for profiler
  ...

3 months agoMerge tag 'sched_ext-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj...
Linus Torvalds [Wed, 20 Nov 2024 18:08:00 +0000 (10:08 -0800)]
Merge tag 'sched_ext-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext

Pull sched_ext updates from Tejun Heo:

 - Improve the default select_cpu() implementation making it topology
   aware and handle WAKE_SYNC better.

 - set_arg_maybe_null() was used to inform the verifier which ops args
   could be NULL in a rather hackish way. Use the new __nullable CFI
   stub tags instead.

 - On Sapphire Rapids multi-socket systems, a BPF scheduler, by
   hammering on the same queue across sockets, could live-lock the
   system to the point where the system couldn't make reasonable forward
   progress.

   This could lead to soft-lockup triggered resets or stalling out
   bypass mode switch and thus BPF scheduler ejection for tens of
   minutes if not hours. After trying a number of mitigations, the
   following set worked reliably:

     - Injecting artificial cpu_relax() loops in two places while
       sched_ext is trying to turn on the bypass mode.

     - Triggering scheduler ejection when soft-lockup detection is
       imminent (a quarter of threshold left).

   While not the prettiest, the impact both in terms of code complexity
   and overhead is minimal.

 - A common complaint on the API is the overuse of the word "dispatch"
   and the confusion around "consume". This is due to how the dispatch
   queues became more generic over time. Rename the affected kfuncs for
   clarity. Thanks to BPF's compatibility features, this change can be
   made in a way that's both forward and backward compatible. The
   compatibility code will be dropped in a few releases.

 - Other misc changes

* tag 'sched_ext-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext: (21 commits)
  sched_ext: Replace scx_next_task_picked() with switch_class() in comment
  sched_ext: Rename scx_bpf_dispatch[_vtime]_from_dsq*() -> scx_bpf_dsq_move[_vtime]*()
  sched_ext: Rename scx_bpf_consume() to scx_bpf_dsq_move_to_local()
  sched_ext: Rename scx_bpf_dispatch[_vtime]() to scx_bpf_dsq_insert[_vtime]()
  sched_ext: scx_bpf_dispatch_from_dsq_set_*() are allowed from unlocked context
  sched_ext: add a missing rcu_read_lock/unlock pair at scx_select_cpu_dfl()
  sched_ext: Clarify sched_ext_ops table for userland scheduler
  sched_ext: Enable the ops breather and eject BPF scheduler on softlockup
  sched_ext: Avoid live-locking bypass mode switching
  sched_ext: Fix incorrect use of bitwise AND
  sched_ext: Do not enable LLC/NUMA optimizations when domains overlap
  sched_ext: Introduce NUMA awareness to the default idle selection policy
  sched_ext: Replace set_arg_maybe_null() with __nullable CFI stub tags
  sched_ext: Rename CFI stubs to names that are recognized by BPF
  sched_ext: Introduce LLC awareness to the default idle selection policy
  sched_ext: Clarify ops.select_cpu() for single-CPU tasks
  sched_ext: improve WAKE_SYNC behavior for default idle CPU selection
  sched_ext: Use btf_ids to resolve task_struct
  sched/ext: Use tg_cgroup() to elieminate duplicate code
  sched/ext: Fix unmatch trailing comment of CONFIG_EXT_GROUP_SCHED
  ...

3 months agoMerge tag 'cgroup-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Linus Torvalds [Wed, 20 Nov 2024 17:54:49 +0000 (09:54 -0800)]
Merge tag 'cgroup-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup

Pull cgroup updates from Tejun Heo:

 - cpu.stat now also shows niced CPU time

 - Freezer and cpuset optimizations

 - Other misc changes

* tag 'cgroup-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup/cpuset: Disable cpuset_cpumask_can_shrink() test if not load balancing
  cgroup/cpuset: Further optimize code if CONFIG_CPUSETS_V1 not set
  cgroup/cpuset: Enforce at most one rebuild_sched_domains_locked() call per operation
  cgroup/cpuset: Revert "Allow suppression of sched domain rebuild in update_cpumasks_hier()"
  MAINTAINERS: remove Zefan Li
  cgroup/freezer: Add cgroup CGRP_FROZEN flag update helper
  cgroup/freezer: Reduce redundant traversal for cgroup_freeze
  cgroup/bpf: only cgroup v2 can be attached by bpf programs
  Revert "cgroup: Fix memory leak caused by missing cgroup_bpf_offline"
  selftests/cgroup: Fix compile error in test_cpu.c
  cgroup/rstat: Selftests for niced CPU statistics
  cgroup/rstat: Tracking cgroup-level niced CPU time
  cgroup/cpuset: Fix spelling errors in file kernel/cgroup/cpuset.c

3 months agoMerge tag 'wq-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Linus Torvalds [Wed, 20 Nov 2024 17:41:11 +0000 (09:41 -0800)]
Merge tag 'wq-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq

Pull workqueue updates from Tejun Heo:

 - The maximum concurrency limit of 512 which was set a long time ago is
   too low now.

   A legitimate use (BPF cgroup release) of system_wq could saturate it
   under stress test conditions leading to false dependencies and
   deadlocks.

   While the offending use was switched to a dedicated workqueue, use
   the opportunity to bump WQ_MAX_ACTIVE four fold and document that
   system workqueue shouldn't be saturated. Workqueue should add at
   least a warning mechanism for cases where system workqueues are
   saturated.

 - Recent workqueue updates to support more flexible execution topology
   made unbound workqueues use per-cpu worker pool frontends which
   pushed up workqueue flush overhead.

   As consecutive CPUs are likely to be pointing to the same worker
   pool, reduce overhead by switching locks only when necessary.

* tag 'wq-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Reduce expensive locks for unbound workqueue
  workqueue: Adjust WQ_MAX_ACTIVE from 512 to 2048
  workqueue: doc: Add a note saturating the system_wq is not permitted

3 months agoMerge tag 'probes-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux...
Linus Torvalds [Wed, 20 Nov 2024 17:36:05 +0000 (09:36 -0800)]
Merge tag 'probes-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull probes updates from Masami Hiramatsu:
 "Kprobes cleanups. Functionality does not change.

   - kprobes: Cleanup the config comment

     Adjust #endif comments.

   - kprobes: Cleanup collect_one_slot() and __disable_kprobe()

     Make fail fast to reduce code nested level.

   - kprobes: Use struct_size() in __get_insn_slot()

     Use struct_size() to avoid special macro.

   - x86/kprobes: Cleanup kprobes on ftrace code

     Use macro instead of direct field access/magic number, and avoid
     redundant instruction pointer setting"

* tag 'probes-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  x86/kprobes: Cleanup kprobes on ftrace code
  kprobes: Use struct_size() in __get_insn_slot()
  kprobes: Cleanup collect_one_slot() and __disable_kprobe()
  kprobes: Cleanup the config comment

3 months agoMerge tag 'livepatching-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Wed, 20 Nov 2024 17:33:23 +0000 (09:33 -0800)]
Merge tag 'livepatching-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching

Pull livepatching update from Petr Mladek:

 - A new selftest for livepatching of a kprobed function

* tag 'livepatching-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
  selftests: livepatch: test livepatching a kprobed function
  selftests: livepatch: save and restore kprobe state
  selftests: livepatch: rename KLP_SYSFS_DIR to SYSFS_KLP_DIR

3 months agoMerge tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk...
Linus Torvalds [Wed, 20 Nov 2024 17:21:11 +0000 (09:21 -0800)]
Merge tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux

Pull printk updates from Petr Mladek:

 - Print more precise information about the printk log buffer memory
   usage.

 - Make sure that the sysrq title is shown on the console even when
   deferred.

 - Do not enable earlycon by `console=` which is meant to disable the
   default console.

* tag 'printk-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  printk: add dummy printk_force_console_enter/exit helpers
  tty: sysrq: Use printk_force_console context on __handle_sysrq
  printk: Introduce FORCE_CON flag
  printk: Improve memory usage logging during boot
  init: Don't proxy `console=` to earlycon

This page took 0.218344 seconds and 4 git commands to generate.