When a CRC error occurs, the HBA asserts an interrupt to indicate an
interface fatal error (PxIS.IFS). The ISR clears PxIE and PxIS, then
does error recovery. If the adapter receives another SDB FIS
with an error (PxIS.TFES) from the device before the start of the EH
recovery process, the interrupt signaling the new SDB cannot be
serviced as PxIE was cleared already. This in turn results in the HBA
inability to issue any command during the error recovery process after
setting PxCMD.ST to 1 because PxIS.TFES is still set.
According to AHCI 1.3.1 specifications section 6.2.2, fatal errors
notified by setting PxIS.HBFS, PxIS.HBDS, PxIS.IFS or PxIS.TFES will
cause the HBA to enter the ERR:Fatal state. In this state, the HBA
shall not issue any new commands.
To avoid this situation, introduce the function
ahci_port_clear_pending_irq() to clear pending interrupts before
executing a COMRESET. This follows the AHCI 1.3.1 - section 6.2.2.2
specification.
Dave Airlie [Thu, 14 Sep 2023 23:50:34 +0000 (09:50 +1000)]
Merge tag 'amd-drm-fixes-6.6-2023-09-13' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.6-2023-09-13:
amdgpu:
- GC 9.4.3 fixes
- Fix white screen issues with S/G display on system with >= 64G of ram
- Replay fixes
- SMU 13.0.6 fixes
- AUX backlight fix
- NBIO 4.3 SR-IOV fixes for HDP
- RAS fixes
- DP MST resume fix
- Fix segfault on systems with no vbios
- DPIA fixes
amdkfd:
- CWSR grace period fix
- Unaligned doorbell fix
- CRIU fix for GFX11
- Add missing TLB flush on gfx10 and newer
Merge tag 'nvme-6.6-2023-09-14' of git://git.infradead.org/nvme into block-6.6
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.6
- nvme-tcp iov len fix (Varun)
- nvme-hwmon const qualifier for safety (Krzysztof)
- nvme-fc null pointer checks (Nigel)
- nvme-pci no numa node fix (Pratyush)
- nvme timeout fix for non-compliant controllers (Keith)"
* tag 'nvme-6.6-2023-09-14' of git://git.infradead.org/nvme:
nvme: avoid bogus CRTO values
nvme-pci: do not set the NUMA node of device if it has none
nvme-fc: Prevent null pointer dereference in nvme_fc_io_getuuid()
nvme: host: hwmon: constify pointers to hwmon_channel_info
nvmet-tcp: pass iov_len instead of sg->length to bvec_set_page()
Keith Busch [Tue, 12 Sep 2023 21:38:58 +0000 (14:38 -0700)]
nvme: avoid bogus CRTO values
Some devices are reporting controller ready mode support, but return 0
for CRTO. These devices require a much higher time to ready than that,
so they are failing to initialize after the driver starter preferring
that value over CAP.TO.
The spec requires that CAP.TO match the appropritate CRTO value, or be
set to 0xff if CRTO is larger than that. This means that CAP.TO can be
used to validate if CRTO is reliable, and provides an appropriate
fallback for setting the timeout value if not. Use whichever is larger.
thermal: core: Fix disabled trip point check in handle_thermal_trip()
Commit bc840ea5f9a9 ("thermal: core: Do not handle trip points with
invalid temperature") added a check for invalid temperature to the
disabled trip point check in handle_thermal_trip(), but that check was
added at a point when the trip structure has not been initialized yet.
This may cause handle_thermal_trip() to skip a valid trip point in some
cases, so fix it by moving the check to a suitable place, after
__thermal_zone_get_trip() has been called to populate the trip
structure.
Fixes: bc840ea5f9a9 ("thermal: core: Do not handle trip points with invalid temperature") Signed-off-by: Rafael J. Wysocki <[email protected]>
* tag 'md-fixes-20230914' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md: Put the right device in md_seq_next
md/raid1: fix error: ISO C90 forbids mixed declarations
md: fix warning for holder mismatch from export_rdev()
md: don't dereference mddev after export_rdev()
Michal Kubecek [Mon, 11 Sep 2023 08:01:29 +0000 (10:01 +0200)]
kbuild: avoid long argument lists in make modules_install
Running "make modules_install" may fail with
make[2]: execvp: /bin/sh: Argument list too long
if many modules are built and INSTALL_MOD_PATH is long. This is because
scripts/Makefile.modinst creates all directories with one mkdir command.
Use $(foreach ...) instead to prevent an excessive argument list.
Fixes: 2dfec887c0fd ("kbuild: reduce the number of mkdir calls during modules_install") Signed-off-by: Michal Kubecek <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]>
kbuild: fix kernel-devel RPM package and linux-headers Deb package
Since commit fe66b5d2ae72 ("kbuild: refactor kernel-devel RPM package
and linux-headers Deb package"), the kernel-devel RPM package and
linux-headers Deb package are broken.
I double-quoted the $(find ... -type d), which resulted in newlines
being included in the argument to the outer find comment.
find: 'arch/arm64/include\narch/arm64/kvm/hyp/include': No such file or directory
The outer find command is unneeded.
Fixes: fe66b5d2ae72 ("kbuild: refactor kernel-devel RPM package and linux-headers Deb package") Reported-by: Karolis M <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]> Reviewed-by: Nicolas Schier <[email protected]>
If there are multiple arrays in system and one mddevice is marked
with MD_DELETED and md_seq_next() is called in the middle of removal
then it _get()s proper device but it may _put() deleted one. As a result,
active counter may never be zeroed for mddevice and it cannot
be removed.
Put the device which has been _get with previous md_seq_next() call.
Merge tag 'net-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Quite unusually, this does not contains any fix coming from subtrees
(nf, ebpf, wifi, etc).
Current release - regressions:
- bcmasp: fix possible OOB write in bcmasp_netfilt_get_all_active()
Previous releases - regressions:
- ipv4: fix one memleak in __inet_del_ifa()
- tcp: fix bind() regressions for v4-mapped-v6 addresses.
- tls: do not free tls_rec on async operation in
bpf_exec_tx_verdict()
- dsa: fixes for SJA1105 FDB regressions
- veth: update XDP feature set when bringing up device
- igb: fix hangup when enabling SR-IOV
Previous releases - always broken:
- kcm: fix memory leak in error path of kcm_sendmsg()
- smc: fix data corruption in smcr_port_add
- microchip: fix possible memory leak for vcap_dup_rule()"
* tag 'net-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
net: renesas: rswitch: Add spin lock protection for irq {un}mask
net: renesas: rswitch: Fix unmasking irq condition
igb: clean up in all error paths when enabling SR-IOV
ixgbe: fix timestamp configuration code
selftest: tcp: Add v4-mapped-v6 cases in bind_wildcard.c.
selftest: tcp: Move expected_errno into each test case in bind_wildcard.c.
selftest: tcp: Fix address length in bind_wildcard.c.
tcp: Fix bind() regression for v4-mapped-v6 non-wildcard address.
tcp: Fix bind() regression for v4-mapped-v6 wildcard address.
tcp: Factorise sk_family-independent comparison in inet_bind2_bucket_match(_addr_any).
ipv6: fix ip6_sock_set_addr_preferences() typo
veth: Update XDP feature set when bringing up device
net: macb: fix sleep inside spinlock
net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
net: ethernet: mtk_eth_soc: fix pse_port configuration for MT7988
net: ethernet: mtk_eth_soc: fix uninitialized variable
kcm: Fix memory leak in error path of kcm_sendmsg()
r8152: check budget for r8152_poll()
net: dsa: sja1105: block FDB accesses that are concurrent with a switch reset
...
Pavel Begunkov [Thu, 14 Sep 2023 15:51:09 +0000 (16:51 +0100)]
io_uring/net: fix iter retargeting for selected buf
When using selected buffer feature, io_uring delays data iter setup
until later. If io_setup_async_msg() is called before that it might see
not correctly setup iterator. Pre-init nr_segs and judge from its state
whether we repointing.
Shida Zhang [Thu, 3 Aug 2023 06:09:38 +0000 (14:09 +0800)]
ext4: fix rec_len verify error
With the configuration PAGE_SIZE 64k and filesystem blocksize 64k,
a problem occurred when more than 13 million files were directly created
under a directory:
EXT4-fs error (device xx): ext4_dx_csum_set:492: inode #xxxx: comm xxxxx: dir seems corrupt? Run e2fsck -D.
EXT4-fs error (device xx): ext4_dx_csum_verify:463: inode #xxxx: comm xxxxx: dir seems corrupt? Run e2fsck -D.
EXT4-fs error (device xx): dx_probe:856: inode #xxxx: block 8188: comm xxxxx: Directory index failed checksum
When enough files are created, the fake_dirent->reclen will be 0xffff.
it doesn't equal to the blocksize 65536, i.e. 0x10000.
But it is not the same condition when blocksize equals to 4k.
when enough files are created, the fake_dirent->reclen will be 0x1000.
it equals to the blocksize 4k, i.e. 0x1000.
The problem seems to be related to the limitation of the 16-bit field
when the blocksize is set to 64k.
To address this, helpers like ext4_rec_len_{from,to}_disk has already
been introduced to complete the conversion between the encoded and the
plain form of rec_len.
So fix this one by using the helper, and all the other in this file too.
Jan Kara [Wed, 13 Sep 2023 15:04:55 +0000 (17:04 +0200)]
ext4: do not let fstrim block system suspend
Len Brown has reported that system suspend sometimes fail due to
inability to freeze a task working in ext4_trim_fs() for one minute.
Trimming a large filesystem on a disk that slowly processes discard
requests can indeed take a long time. Since discard is just an advisory
call, it is perfectly fine to interrupt it at any time and the return
number of discarded blocks until that moment. Do that when we detect the
task is being frozen.
Jan Kara [Wed, 13 Sep 2023 15:04:54 +0000 (17:04 +0200)]
ext4: move setting of trimmed bit into ext4_try_to_trim_range()
Currently we set the group's trimmed bit in ext4_trim_all_free() based
on return value of ext4_try_to_trim_range(). However when we will want
to abort trimming because of suspend attempt, we want to return success
from ext4_try_to_trim_range() but not set the trimmed bit. Instead
implementing awkward propagation of this information, just move setting
of trimmed bit into ext4_try_to_trim_range() when the whole group is
trimmed.
The root cause was traced to an error handing path in journal_init_common()
when malloc memory failed in register_shrinker(). The checksum driver is
used to reference to checksum algorithm via cryptoapi and the user should
release the memory when the driver is no longer needed or the journal
initialization failed.
Fix it by calling crypto_free_shash() on the "err_cleanup" error handing
path in journal_init_common().
Mikulas Patocka [Wed, 9 Aug 2023 10:44:20 +0000 (12:44 +0200)]
dm: fix a race condition in retrieve_deps
There's a race condition in the multipath target when retrieve_deps
races with multipath_message calling dm_get_device and dm_put_device.
retrieve_deps walks the list of open devices without holding any lock
but multipath may add or remove devices to the list while it is
running. The end result may be memory corruption or use-after-free
memory access.
See this description of a UAF with multipath_message():
https://listman.redhat.com/archives/dm-devel/2022-October/052373.html
Fix this bug by introducing a new rw semaphore "devices_lock". We grab
devices_lock for read in retrieve_deps and we grab it for write in
dm_get_device and dm_put_device.
when using __drm_kunit_helper_alloc_drm_device() the driver may be
dereferenced by device-managed resources up until the device is
freed, which is typically later than the kunit-managed resource code
frees it. Fix this by simply make the driver device-managed as well.
In short, the sequence leading to the UAF is as follows:
INIT:
Code allocates a struct device as a kunit-managed resource.
Code allocates a drm driver as a kunit-managed resource.
Code allocates a drm device as a device-managed resource.
EXIT:
Kunit resource cleanup frees the drm driver
Kunit resource cleanup puts the struct device, which starts a
device-managed resource cleanup
device-managed cleanup calls drm_dev_put()
drm_dev_put() dereferences the (now freed) drm driver -> Boom.
Related KASAN message:
[55272.551542] ==================================================================
[55272.551551] BUG: KASAN: slab-use-after-free in drm_dev_put.part.0+0xd4/0xe0 [drm]
[55272.551603] Read of size 8 at addr ffff888127502828 by task kunit_try_catch/10353
[55272.552096] The buggy address belongs to the object at ffff888127502800
which belongs to the cache kmalloc-512 of size 512
[55272.552105] The buggy address is located 40 bytes inside of
freed 512-byte region [ffff888127502800, ffff888127502a00)
[55272.552163] Memory state around the buggy address:
[55272.552167] ffff888127502700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[55272.552173] ffff888127502780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[55272.552178] >ffff888127502800: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[55272.552184] ^
[55272.552187] ffff888127502880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[55272.552193] ffff888127502900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[55272.552198] ==================================================================
[55272.552203] Disabling lock debugging due to kernel taint
v2:
- Update commit message, add Fixes: tag and Cc stable.
v3:
- Further commit message updates (Maxime Ripard).
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88bd720
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.
However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.
When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().
Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up. However, we have
yet to get such a report, and only syzkaller stumbled on it. So, this
can be changed safely.
Note this does not change SOCK_SEQPACKET behaviour.
====================
net: renesas: rswitch: Fix a lot of redundant irq issue
After this patch series was applied, a lot of redundant interrupts
no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
====================
net: renesas: rswitch: Add spin lock protection for irq {un}mask
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"") Signed-off-by: Yoshihiro Shimoda <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
Justin Tee [Fri, 8 Sep 2023 21:19:23 +0000 (14:19 -0700)]
scsi: lpfc: Prevent use-after-free during rmmod with mapped NVMe rports
During rmmod, when dev_loss_tmo callback is called, an ndlp kref count is
decremented twice. Once for SCSI transport registration and second to
remove the initial node allocation kref. If there is also an NVMe
transport registration, another reference count decrement is expected in
lpfc_nvme_unregister_port().
Race conditions between the NVMe transport remoteport_delete and
dev_loss_tmo callbacks sometimes results in premature ndlp object release
resulting in use-after-free issues.
Fix by not dropping the ndlp object in dev_loss_tmo callback with an
outstanding NVMe transport registration. Inversely, mark the final
NLP_DROPPED flag in lpfc_nvme_unregister_port when rmmod flag is set.
Justin Tee [Fri, 8 Sep 2023 21:18:52 +0000 (14:18 -0700)]
scsi: lpfc: Early return after marking final NLP_DROPPED flag in dev_loss_tmo
When a dev_loss_tmo event occurs, an ndlp lock is taken before checking
nlp_flag for NLP_DROPPED. There is an attempt to restore the ndlp lock
when exiting the if statement, but the nlp_put kref could be the final
decrement causing a use-after-free memory access on a released ndlp object.
Instead of trying to reacquire the ndlp lock after checking nlp_flag, just
return after calling nlp_put.
Damien Le Moal [Mon, 11 Sep 2023 23:27:36 +0000 (08:27 +0900)]
scsi: pm8001: Setup IRQs on resume
The function pm8001_pci_resume() only calls pm8001_request_irq() without
calling pm8001_setup_irq(). This causes the IRQ allocation to fail, which
leads all drives being removed from the system.
Fix this issue by integrating the code for pm8001_setup_irq() directly
inside pm8001_request_irq() so that MSI-X setup is performed both during
normal initialization and resume operations.
Merge tag 'pmdomain-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull genpm / pmdomain rename from Ulf Hansson:
"This renames the genpd subsystem to pmdomain.
As discussed on LKML, using 'genpd' as the name of a subsystem isn't
very self-explanatory and the acronym itself that means Generic PM
Domain, is known only by a limited group of people.
The suggestion to improve the situation is to rename the subsystem to
'pmdomain', which there seems to be a good consensus around using.
Ideally it should indicate that its purpose is to manage Power Domains
or 'PM domains' as we often also use within the Linux Kernel
terminology"
* tag 'pmdomain-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: Rename the genpd subsystem to pmdomain
Merge tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- fix reference to exported symbols for parisc64 [Masahiro Yamada]
- Block-TLB (BTLB) support on 32-bit CPUs
- sparse and build-warning fixes
* tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
linux/export: fix reference to exported functions for parisc64
parisc: BTLB: Initialize BTLB tables at CPU startup
parisc: firmware: Simplify calling non-PA20 functions
parisc: BTLB: _edata symbol has to be page aligned for BTLB support
parisc: BTLB: Add BTLB insert and purge firmware function wrappers
parisc: BTLB: Clear possibly existing BTLB entries
parisc: Prepare for Block-TLB support on 32-bit kernel
parisc: shmparam.h: Document aliasing requirements of PA-RISC
parisc: irq: Make irq_stack_union static to avoid sparse warning
parisc: drivers: Fix sparse warning
parisc: iosapic.c: Fix sparse warnings
parisc: ccio-dma: Fix sparse warnings
parisc: sba-iommu: Fix sparse warnigs
parisc: sba: Fix compile warning wrt list of SBA devices
parisc: sba_iommu: Fix build warning if procfs if disabled
Merge tag 'trace-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Add missing LOCKDOWN checks for eventfs callers
When LOCKDOWN is active for tracing, it causes inconsistent state
when some functions succeed and others fail.
- Use dput() to free the top level eventfs descriptor
There was a race between accesses and freeing it.
- Fix a long standing bug that eventfs exposed due to changing timings
by dynamically creating files. That is, If a event file is opened for
an instance, there's nothing preventing the instance from being
removed which will make accessing the files cause use-after-free
bugs.
- Fix a ring buffer race that happens when iterating over the ring
buffer while writers are active. Check to make sure not to read the
event meta data if it's beyond the end of the ring buffer sub buffer.
- Fix the print trigger that disappeared because the test to create it
was looking for the event dir field being filled, but now it has the
"ef" field filled for the eventfs structure.
- Remove the unused "dir" field from the event structure.
- Fix the order of the trace_dynamic_info as it had it backwards for
the offset and len fields for which one was for which endianess.
- Fix NULL pointer dereference with eventfs_remove_rec()
If an allocation fails in one of the eventfs_add_*() functions, the
caller of it in event_subsystem_dir() or event_create_dir() assigns
the result to the structure. But it's assigning the ERR_PTR and not
NULL. This was passed to eventfs_remove_rec() which expects either a
good pointer or a NULL, not ERR_PTR. The fix is to not assign the
ERR_PTR to the structure, but to keep it NULL on error.
- Fix list_for_each_rcu() to use list_for_each_srcu() in
dcache_dir_open_wrapper(). One iteration of the code used RCU but
because it had to call sleepable code, it had to be changed to use
SRCU, but one of the iterations was missed.
- Fix synthetic event print function to use "as_u64" instead of passing
in a pointer to the union. To fix big/little endian issues, the u64
that represented several types was turned into a union to define the
types properly.
* tag 'trace-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Fix the NULL pointer dereference bug in eventfs_remove_rec()
tracefs/eventfs: Use list_for_each_srcu() in dcache_dir_open_wrapper()
tracing/synthetic: Print out u64 values properly
tracing/synthetic: Fix order of struct trace_dynamic_info
selftests/ftrace: Fix dependencies for some of the synthetic event tests
tracing: Remove unused trace_event_file dir field
tracing: Use the new eventfs descriptor for print trigger
ring-buffer: Do not attempt to read past "commit"
tracefs/eventfs: Free top level files on removal
ring-buffer: Avoid softlockup in ring_buffer_resize()
tracing: Have event inject files inc the trace array ref count
tracing: Have option files inc the trace array ref count
tracing: Have current_trace inc the trace array ref count
tracing: Have tracing_max_latency inc the trace array ref count
tracing: Increase trace array ref count on enable and filter files
tracefs/eventfs: Use dput to free the toplevel events directory
tracefs/eventfs: Add missing lockdown checks
tracefs: Add missing lockdown check to tracefs_create_dir()
Ricardo Neri [Tue, 15 Aug 2023 03:57:47 +0000 (20:57 -0700)]
x86/sched: Restore the SD_ASYM_PACKING flag in the DIE domain
Commit 8f2d6c41e5a6 ("x86/sched: Rewrite topology setup") dropped the
SD_ASYM_PACKING flag in the DIE domain added in commit 044f0e27dec6
("x86/sched: Add the SD_ASYM_PACKING flag to the die domain of hybrid
processors"). Restore it on hybrid processors.
The die-level domain does not depend on any build configuration and now
x86_sched_itmt_flags() is always needed. Remove the build dependency on
CONFIG_SCHED_[SMT|CLUSTER|MC].
Tim Chen [Thu, 7 Sep 2023 17:42:21 +0000 (10:42 -0700)]
sched/fair: Fix SMT4 group_smt_balance handling
For SMT4, any group with more than 2 tasks will be marked as
group_smt_balance. Retain the behaviour of group_has_spare by marking
the busiest group as the group which has the least number of idle_cpus.
Also, handle rounding effect of adding (ncores_local + ncores_busy) when
the local is fully idle and busy group imbalance is less than 2 tasks.
Local group should try to pull at least 1 task in this case so imbalance
should be set to 2 instead.
igb: clean up in all error paths when enabling SR-IOV
After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails.
The commit in fixes introduced flags to control the status of hardware
configuration while processing packets. At the same time another structure
is used to provide configuration of timestamper to user-space applications.
The way it was coded makes this structures go out of sync easily. The
repro is easy for 82599 chips:
The eth0 device is properly configured to timestamp any PTPv2 events.
[root@hostname ~]# hwstamp_ctl -i eth0 -r 1 -t 1
current settings:
tx_type 1
rx_filter 12
SIOCSHWTSTAMP failed: Numerical result out of range
The requested time stamping mode is not supported by the hardware.
The error is properly returned because HW doesn't support all packets
timestamping. But the adapter->flags is cleared of timestamp flags
even though no HW configuration was done. From that point no RX timestamps
are received by user-space application. But configuration shows good
values:
Fix the issue by applying new flags only when the HW was actually
configured.
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices") Signed-off-by: Vadim Fedorenko <[email protected]> Reviewed-by: Simon Horman <[email protected]> Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: David S. Miller <[email protected]>
It has been pointed out that naming a subsystem "genpd" isn't very
self-explanatory and the acronym itself that means Generic PM Domain, is
known only by a limited group of people.
In a way to improve the situation, let's rename the subsystem to pmdomain,
which ideally should indicate that this is about so called Power Domains or
"PM domains" as we often also use within the Linux Kernel terminology.
Tommy Huang [Wed, 6 Sep 2023 00:49:10 +0000 (08:49 +0800)]
i2c: aspeed: Reset the i2c controller when timeout occurs
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
The "i2c_mlxcpld" platform device is only instantiated on X86 systems
(through drivers/platform/x86/mlx-platform.c), or on ARM64 systems with
ACPI (through drivers/platform/mellanox/nvsw-sn2201.c). Hence further
restrict the dependency on ARM64 to ACPI, to prevent asking the user
about this driver when configuring an ARM64 kernel without ACPI support.
While at it, document in the Kconfig help text that the driver supports
ARM64/ACPI based systems, too.
I2C Address Translator (ATR) support is not a stand-alone driver, but a
library. All of its users select I2C_ATR. Hence there is no need for
the user to enable this symbol manually, except when compile-testing.
w1: ds2482: Switch back to use struct i2c_driver's .probe()
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Just after bhash2:
$ uname -r 6.0.0-rc1-00394-g28044fc1d495
$ ./bind_wildcard
...
ok 15 bind_wildcard.v4_local_v6_v4mapped_local.v4_v6
not ok 16 bind_wildcard.v4_local_v6_v4mapped_local.v6_v4
# FAILED: 15 / 16 tests passed.
On net.git:
$ ./bind_wildcard
...
not ok 14 bind_wildcard.v4_local_v6_v4mapped_any.v6_v4
not ok 16 bind_wildcard.v4_local_v6_v4mapped_local.v6_v4
# FAILED: 13 / 16 tests passed.
With this series:
$ ./bind_wildcard
...
# PASSED: 16 / 16 tests passed.
selftest: tcp: Fix address length in bind_wildcard.c.
The selftest passes the IPv6 address length for an IPv4 address.
We should pass the correct length.
Note inet_bind_sk() does not check if the size is larger than
sizeof(struct sockaddr_in), so there is no real bug in this
selftest.
Fixes: 13715acf8ab5 ("selftest: Add test for bind() conflicts.") Signed-off-by: Kuniyuki Iwashima <[email protected]> Signed-off-by: David S. Miller <[email protected]>
During the 2nd bind() in inet_csk_get_port(), inet_bind2_bucket_find()
fails to find the 1st socket's tb2, so inet_bind2_bucket_create() allocates
a new tb2 for the 2nd socket. Then, we call inet_csk_bind_conflict() that
checks conflicts in the new tb2 by inet_bhash2_conflict(). However, the
new tb2 does not include the 1st socket, thus the bind() finally succeeds.
In this case, inet_bind2_bucket_match() must check if AF_INET6 tb2 has
the conflicting v4-mapped-v6 address so that inet_bind2_bucket_find()
returns the 1st socket's tb2.
Note that if we bind two sockets to 127.0.0.1 and then ::FFFF:127.0.0.1,
the 2nd bind() fails properly for the same reason mentinoed in the previous
commit.
During the 2nd bind(), if tb->family is AF_INET6 and sk->sk_family is
AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the v4-mapped-v6 wildcard address.
The example above does not work after commit 5456262d2baa ("net: Fix
incorrect address comparison when searching for a bind2 bucket"), but
the blamed change is not the commit.
Before the commit, the leading zeros of ::FFFF:0.0.0.0 were treated
as 0.0.0.0, and the sequence above worked by chance. Technically, this
case has been broken since bhash2 was introduced.
Note that if we bind() two sockets to 127.0.0.1 and then ::FFFF:0.0.0.0,
the 2nd bind() fails properly because we fall back to using bhash to
detect conflicts for the v4-mapped-v6 address.
Ondrej Mosnacek [Mon, 11 Sep 2023 14:23:58 +0000 (16:23 +0200)]
selinux: fix handling of empty opts in selinux_fs_context_submount()
selinux_set_mnt_opts() relies on the fact that the mount options pointer
is always NULL when all options are unset (specifically in its
!selinux_initialized() branch. However, the new
selinux_fs_context_submount() hook breaks this rule by allocating a new
structure even if no options are set. That causes any submount created
before a SELinux policy is loaded to be rejected in
selinux_set_mnt_opts().
Fix this by making selinux_fs_context_submount() leave fc->security
set to NULL when there are no options to be copied from the reference
superblock.
Song Shuai [Wed, 6 Sep 2023 09:58:17 +0000 (17:58 +0800)]
riscv: kexec: Align the kexeced kernel entry
The current riscv boot protocol requires 2MB alignment for RV64
and 4MB alignment for RV32.
In KEXEC_FILE path, the elf_find_pbase() function should align
the kexeced kernel entry according to the requirement, otherwise
the kexeced kernel would silently BUG at the setup_vm().
Commit d2e8071bed0be ("tpm: make all 'class' structures const")
unfortunately had a typo for the name on tpmrm.
Fixes: d2e8071bed0b ("tpm: make all 'class' structures const") Signed-off-by: Justin M. Forbes <[email protected]> Signed-off-by: Jarkko Sakkinen <[email protected]>
Steve French [Tue, 12 Sep 2023 19:08:36 +0000 (14:08 -0500)]
smb3: move server check earlier when setting channel sequence number
Smatch warning pointed out by Dan Carpenter:
fs/smb/client/smb2pdu.c:105 smb2_hdr_assemble()
warn: variable dereferenced before check 'server' (see line 95)
Fixes: 09ee7a3bf866 ("[SMB3] send channel sequence number in SMB3 requests after reconnects") Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Steve French <[email protected]>
Merge tag 'for-6.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- several fixes for handling directory item (inserting, removing,
iteration, error handling)
- fix transaction commit stalls when auto relocation is running and
blocks other tasks that want to commit
- fix a build error when DEBUG is enabled
- fix lockdep warning in inode number lookup ioctl
- fix race when finishing block group creation
- remove link to obsolete wiki in several files
* tag 'for-6.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
MAINTAINERS: remove links to obsolete btrfs.wiki.kernel.org
btrfs: assert delayed node locked when removing delayed item
btrfs: remove BUG() after failure to insert delayed dir index item
btrfs: improve error message after failure to add delayed dir index item
btrfs: fix a compilation error if DEBUG is defined in btree_dirty_folio
btrfs: check for BTRFS_FS_ERROR in pending ordered assert
btrfs: fix lockdep splat and potential deadlock after failure running delayed items
btrfs: do not block starts waiting on previous transaction commit
btrfs: release path before inode lookup during the ino lookup ioctl
btrfs: fix race between finishing block group creation and its item update
Merge tag 'platform-drivers-x86-v6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- various platform/mellanox fixes
- one new DMI quirk for asus-wmi
* tag 'platform-drivers-x86-v6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Support 2023 ROG X16 tablet mode
platform/mellanox: NVSW_SN2201 should depend on ACPI
platform/mellanox: mlxbf-bootctl: add NET dependency into Kconfig
platform/mellanox: mlxbf-pmc: Fix reading of unprogrammed events
platform/mellanox: mlxbf-pmc: Fix potential buffer overflows
platform/mellanox: mlxbf-tmfifo: Drop jumbo frames
platform/mellanox: mlxbf-tmfifo: Drop the Rx packet if no more descriptors
* tag 'linux-kselftest-next-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Keep symlinks, when possible
selftests: fix dependency checker script
kselftest/runner.sh: Propagate SIGTERM to runner child
selftests/ftrace: Correctly enable event in instance-event.tc
nvme-pci: do not set the NUMA node of device if it has none
If a device has no NUMA node information associated with it, the driver
puts the device in node first_memory_node (say node 0). Not having a
NUMA node and being associated with node 0 are completely different
things and it makes little sense to mix the two.
Merge tag 'linux-kselftest-kunit-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan:
"Fixes to possible memory leak, null-ptr-deref, wild-memory-access, and
error path bugs"
* tag 'linux-kselftest-kunit-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: Fix possible memory leak in kunit_filter_suites()
kunit: Fix possible null-ptr-deref in kunit_parse_glob_filter()
kunit: Fix the wrong err path and add goto labels in kunit_filter_suites()
kunit: Fix wild-memory-access bug in kunit_free_suite_set()
kunit: test: Make filter strings in executor_test writable
Merge tag 'ovl-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Amir Goldstein:
"Two fixes for pretty old regressions"
* tag 'ovl-fixes-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix incorrect fdput() on aio completion
ovl: fix failed copyup of fileattr on a symlink
Peter Zijlstra [Wed, 2 Aug 2023 10:55:47 +0000 (12:55 +0200)]
x86/ibt: Avoid duplicate ENDBR in __put_user_nocheck*()
Commit cb855971d717 ("x86/putuser: Provide room for padding") changed
__put_user_nocheck_*() into proper functions but failed to note that
SYM_FUNC_START() already provides ENDBR, rendering the explicit ENDBR
superfluous.
Peter Zijlstra [Wed, 2 Aug 2023 10:55:46 +0000 (12:55 +0200)]
x86/ibt: Suppress spurious ENDBR
It was reported that under certain circumstances GCC emits ENDBR
instructions for _THIS_IP_ usage. Specifically, when it appears at the
start of a basic block -- but not elsewhere.
Since _THIS_IP_ is never used for control flow, these ENDBR
instructions are completely superfluous. Override the _THIS_IP_
definition for x86_64 to avoid this.
veth: Update XDP feature set when bringing up device
There's an early return in veth_set_features() if the device is in a down
state, which leads to the XDP feature flags not being updated when enabling
GRO while the device is down. Which in turn leads to XDP_REDIRECT not
working, because the redirect code now checks the flags.
Fix this by updating the feature flags after bringing the device up.
Before this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: no
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: no
After this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: yes
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: yes
eventfs: Fix the NULL pointer dereference bug in eventfs_remove_rec()
Inject fault while probing btrfs.ko, if kstrdup() fails in
eventfs_prepare_ef() in eventfs_add_dir(), it will return ERR_PTR
to assign file->ef. But the eventfs_remove() check NULL in
trace_module_remove_events(), which causes the below NULL
pointer dereference.
As both Masami and Steven suggest, allocater side should handle the
error carefully and remove it, so fix the places where it failed.
Andy Shevchenko [Mon, 28 Aug 2023 14:58:24 +0000 (17:58 +0300)]
driver core: return an error when dev_set_name() hasn't happened
The commit d21fdd07cea4 ("driver core: Return proper error code when
dev_set_name() fails") rewrote the logic of handling the dev_set_name()
error codes, but missed the point that initially set error value to
-EINVAL might be rewritten and hence the error path can't be triggered
at some circumstances. To fix this, make sure that error variable is
set to -EINVAL when other conditionals are false.
The commit makes it impossible to select configuration options that
depend on COMEDI_8254, COMEDI_DAS08, COMEDI_NI_LABPC, or
COMEDI_AMPLC_DIO200 options due to changing 'select' directives to
'depends on' directives and there being no other way to select those
codependent configuration options.
NFSD: fix possible oops when nfsd/pool_stats is closed.
If /proc/fs/nfsd/pool_stats is open when the last nfsd thread exits, then
when the file is closed a NULL pointer is dereferenced.
This is because nfsd_pool_stats_release() assumes that the
pointer to the svc_serv cannot become NULL while a reference is held.
This used to be the case but a recent patch split nfsd_last_thread() out
from nfsd_put(), and clearing the pointer is done in nfsd_last_thread().
This is easily reproduced by running
rpc.nfsd 8 ; ( rpc.nfsd 0;true) < /proc/fs/nfsd/pool_stats
Fortunately nfsd_pool_stats_release() has easy access to the svc_serv
pointer, and so can call svc_put() on it directly.
Fixes: 9f28a971ee9f ("nfsd: separate nfsd_last_thread() from nfsd_put()") Signed-off-by: NeilBrown <[email protected]> Reviewed-by: Jeff Layton <[email protected]> Signed-off-by: Chuck Lever <[email protected]>
The obvious fix is to move the call to macb_set_tx_clk() out of the
protected area. This seems safe as rx and tx are both disabled anyway at
this point.
It is however not entirely clear what the spinlock shall protect. It
could be the read-modify-write access to the NCFGR register, but this
is accessed in macb_set_rx_mode() and macb_set_rxcsum_feature() as well
without holding the spinlock. It could also be the register accesses
done in mog_init_rings() or macb_init_buffers(), but again these
functions are called without holding the spinlock in macb_hresp_error_task().
The locking seems fishy in this driver and it might deserve another look
before this patch is applied.
Ville Syrjälä [Fri, 8 Sep 2023 05:25:27 +0000 (08:25 +0300)]
drm/i915: Only check eDP HPD when AUX CH is shared
Apparently Acer Chromebook C740 (BDW-ULT) doesn't have the
eDP HPD line properly connected, and thus fails the new
HPD check during eDP probe. The result is that we lose the
eDP output.
I suspect all such machines would be Chromebooks or other
Linux exclusive systems as the Windows driver likely wouldn't
work either. I did check a few other BDW machines here and
those do have eDP HPD connected, one of them even is a
different Chromebook (Samus).
To account for these funky machines let's skip the HPD check when
it looks like the eDP port is the only one using that specific AUX
channel. In case of multiple ports sharing the same AUX CH (eg. on
Asrock B250M-HDV) we still do the check and thus should correctly
ignore the eDP port in favor of the other DP port (usually a DP->VGA
converter).
PM: hibernate: Fix the exclusive get block device in test_resume mode
Commit 5904de0d735b ("PM: hibernate: Do not get block device exclusively
in test_resume mode") fixes a hibernation issue under test_resume mode.
That commit is supposed to open the block device in non-exclusive mode
when in test_resume. However the code does the opposite, which is against
its description.
In summary, the swap device is only opened exclusively by swsusp_check()
with its corresponding *close(), and must be in non test_resume mode.
This is to avoid the race condition that different processes scribble the
device at the same time. All the other cases should use non-exclusive mode.
Fix it by really disabling exclusive mode under test_resume.
PM: hibernate: Rename function parameter from snapshot_test to exclusive
Several functions reply on snapshot_test to decide whether to
open the resume device exclusively. However there is no strict
connection between the snapshot_test and the open mode. Rename
the 'snapshot_test' input parameter to 'exclusive' to better reflect
the use case.
Liu Jian [Sat, 9 Sep 2023 08:14:34 +0000 (16:14 +0800)]
net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
I got the below warning when do fuzzing test:
BUG: KASAN: null-ptr-deref in scatterwalk_copychunks+0x320/0x470
Read of size 4 at addr 0000000000000008 by task kworker/u8:1/9
This is because the value of rec_seq of tls_crypto_info configured by the
user program is too large, for example, 0xffffffffffffff. In addition, TLS
is asynchronously accelerated. When tls_do_encryption() returns
-EINPROGRESS and sk->sk_err is set to EBADMSG due to rec_seq overflow,
skmsg is released before the asynchronous encryption process ends. As a
result, the UAF problem occurs during the asynchronous processing of the
encryption module.
If the operation is asynchronous and the encryption module returns
EINPROGRESS, do not free the record information.
tracefs/eventfs: Use list_for_each_srcu() in dcache_dir_open_wrapper()
The eventfs files list is protected by SRCU. In earlier iterations it was
protected with just RCU, but because it needed to also call sleepable
code, it had to be switch to SRCU. The dcache_dir_open_wrapper()
list_for_each_rcu() was missed and did not get converted over to
list_for_each_srcu(). That needs to be fixed.
Create the config file in user_events directory of testcase which
need more kernel configuration than the default defconfig. User
could use these configs with merge_config.sh script:
The Kconfig CONFIG_USER_EVENTS=y is needed for the test to read
data from the following files,
- "/sys/kernel/tracing/user_events_data"
- "/sys/kernel/tracing/user_events_status"
- "/sys/kernel/tracing/events/user_events/*"
Enable config for specific testcase:
(export ARCH=xxx #for cross compiling)
./scripts/kconfig/merge_config.sh .config \
tools/testing/selftests/user_events/config
Enable configs for all testcases:
(export ARCH=xxx #for cross compiling)
./scripts/kconfig/merge_config.sh .config \
tools/testing/selftests/*/config
selftests/user_events: Fix failures when user_events is not installed
When user_events is not installed the self tests currently fail. Now
that these self tests run by default we need to ensure they don't fail
when user_events was not enabled for the kernel being tested.
Add common methods to detect if tracefs and user_events is enabled. If
either is not enabled skip the test. If tracefs is enabled, but is not
mounted, mount tracefs and fail if there were any errors. Fail if not
run as root.
Mustapha Ghaddar [Tue, 22 Aug 2023 20:18:03 +0000 (16:18 -0400)]
drm/amd/display: Fix 2nd DPIA encoder Assignment
[HOW & Why]
There seems to be an issue with 2nd DPIA acquiring link encoder for tiled displays.
Solution is to remove check for eng_id before we get first dynamic encoder for it
Fix the typo in the kernel-doc for @replay_mode to prevent
kernel-doc warnings:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:623: warning: Incorrect use of kernel-doc format: * @replay mode: Replay supported
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:626: warning: Function parameter or member 'replay_mode' not described in 'amdgpu_hdmi_vsdb_info'
Tero Kristo [Mon, 11 Sep 2023 14:17:04 +0000 (17:17 +0300)]
tracing/synthetic: Print out u64 values properly
The synth traces incorrectly print pointer to the synthetic event values
instead of the actual value when using u64 type. Fix by addressing the
contents of the union properly.
projects / linux.git / log