Nathan Sullivan [Tue, 5 May 2015 20:00:25 +0000 (15:00 -0500)]
net: macb: Handle the RXUBR interrupt on all devices
The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices. The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
This patch-set contains bug fixes for state-recovery at the RDS
layer when the underlying transport is TCP and the TCP state at one
of the endpoints is reset
V2 changes: DaveM comments to reduce memory footprint, follow
NFS/RPC model where possible. Added test-case #3
Without the changes in this set, when one of the endpoints is reset,
the existing code does not correctly clean up RDS socket state for stale
connections, resulting in some unstable, timing-dependant behavior on
the wire, including an infinite exchange of 3WHs back-and-forth, and a
resulting potential to never converge RDS state.
Test cases used to verify the changes in this set are:
1. Start rds client/server applications on two participating nodes,
node1 and node2. After at least one packet has been sent (to establish
the TCP connection), restart the rds_tcp module on the client, and
now resend packets. Tcpdump should show server sending a FIN for the
"old" client port, and clean connection establishment/exchange for
the new client port.
2. At the end of step 1, restart rds srever on node2, and start client on
node1, make sure using tcpdump, 'netstat -an|grep 16385' that
packets flow correctly.
3. start RDS client/server application on two participating nodes, and
repeat steps 1 and 2, but this time, simulate node failure by doing
"ifconfig <intf> down", so no FIN is sent.
====================
net/rds: RDS-TCP: only initiate reconnect attempt on outgoing TCP socket.
When the peer of an RDS-TCP connection restarts, a reconnect
attempt should only be made from the active side of the TCP
connection, i.e. the side that has a transient TCP port
number. Do not add the passive side of the TCP connection
to the c_hash_node and thus avoid triggering rds_queue_reconnect()
for passive rds connections.
net/rds: RDS-TCP: Always create a new rds_sock for an incoming connection.
When running RDS over TCP, the active (client) side connects to the
listening ("passive") side at the RDS_TCP_PORT. After the connection
is established, if the client side reboots (potentially without even
sending a FIN) the server still has a TCP socket in the esablished
state. If the server-side now gets a new SYN comes from the client
with a different client port, TCP will create a new socket-pair, but
the RDS layer will incorrectly pull up the old rds_connection (which
is still associated with the stale t_sock and RDS socket state).
This patch corrects this behavior by having rds_tcp_accept_one()
always create a new connection for an incoming TCP SYN.
The rds and tcp state associated with the old socket-pair is cleaned
up via the rds_tcp_state_change() callback which would typically be
invoked in most cases when the client-TCP sends a FIN on TCP restart,
triggering a transition to CLOSE_WAIT state. In the rarer event of client
death without a FIN, TCP_KEEPALIVE probes on the socket will detect
the stale socket, and the TCP transition to CLOSE state will trigger
the RDS state cleanup.
Markus Stenberg [Tue, 5 May 2015 10:36:59 +0000 (13:36 +0300)]
ipv6: Fixed source specific default route handling.
If there are only IPv6 source specific default routes present, the
host gets -ENETUNREACH on e.g. connect() because ip6_dst_lookup_tail
calls ip6_route_output first, and given source address any, it fails,
and ip6_route_get_saddr is never called.
The change is to use the ip6_route_get_saddr, even if the initial
ip6_route_output fails, and then doing ip6_route_output _again_ after
we have appropriate source address available.
Note that this is '99% fix' to the problem; a correct fix would be to
do route lookups only within addrconf.c when picking a source address,
and never call ip6_route_output before source address has been
populated.
David S. Miller [Sat, 9 May 2015 19:51:00 +0000 (15:51 -0400)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
Here are a couple of important Bluetooth & mac802154 fixes for 4.1:
- mac802154 fix for crypto algorithm allocation failure checking
- mac802154 wpan phy leak fix for error code path
- Fix for not calling Bluetooth shutdown() if interface is not up
Let me know if there are any issues pulling. Thanks.
====================
Linus Torvalds [Sat, 9 May 2015 04:39:12 +0000 (21:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes for bugs caught while digging in fs/namei.c. The
first one is this cycle regression, the second is 3.11 and later"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
Al Viro [Sat, 9 May 2015 02:53:15 +0000 (22:53 -0400)]
path_openat(): fix double fput()
path_openat() jumps to the wrong place after do_tmpfile() - it has
already done path_cleanup() (as part of path_lookupat() called by
do_tmpfile()), so doing that again can lead to double fput().
Al Viro [Thu, 7 May 2015 23:24:57 +0000 (19:24 -0400)]
namei: d_is_negative() should be checked before ->d_seq validation
Fetching ->d_inode, verifying ->d_seq and finding d_is_negative() to
be true does *not* mean that inode we'd fetched had been NULL - that
holds only while ->d_seq is still unchanged.
Shift d_is_negative() checks into lookup_fast() prior to ->d_seq
verification.
Linus Torvalds [Sat, 9 May 2015 03:59:02 +0000 (20:59 -0700)]
Merge branch 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"When an arm user reported crashes near page_address(page) in my new
code, it became clear that I can't be trusted with GFP masks. Filipe
beat me to the patch, and I'll just be in the corner with my dunce cap
on"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong mapping flags for free space inode
Linus Torvalds [Sat, 9 May 2015 03:38:21 +0000 (20:38 -0700)]
Merge tag 'dm-4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two additional fixes for changes introduced via DM during the 4.1
merge window.
The first reverts a dm-crypt change that wasn't correct. The second
fixes a device format regression that impacted userspace"
* tag 'dm-4.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
init: fix regression by supporting devices with major:minor:offset format
Revert "dm crypt: fix deadlock when async crypto algorithm returns -EBUSY"
Linus Torvalds [Sat, 9 May 2015 02:49:35 +0000 (19:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes since the merge window;
- fix for a double elevator module release, from Chao Yu. Ancient bug.
- the splice() MORE flag fix from Christophe Leroy.
- a fix for NVMe, fixing a patch that went in in the merge window.
From Keith.
- two fixes for blk-mq CPU hotplug handling, from Ming Lei.
- bdi vs blockdev lifetime fix from Neil Brown, fixing and oops in md.
- two blk-mq fixes from Shaohua, fixing a race on queue stop and a
bad merge issue with FUA writes.
- division-by-zero fix for writeback from Tejun.
- a block bounce page accounting fix, making sure we inc/dec after
bouncing so that pre/post IO pages match up. From Wang YanQing"
* 'for-linus' of git://git.kernel.dk/linux-block:
splice: sendfile() at once fails for big files
blk-mq: don't lose requests if a stopped queue restarts
blk-mq: fix FUA request hang
block: destroy bdi before blockdev is unregistered.
block:bounce: fix call inc_|dec_zone_page_state on different pages confuse value of NR_BOUNCE
elevator: fix double release of elevator module
writeback: use |1 instead of +1 to protect against div by zero
blk-mq: fix CPU hotplug handling
blk-mq: fix race between timeout and CPU hotplug
NVMe: Fix VPD B0 max sectors translation
Linus Torvalds [Sat, 9 May 2015 02:42:59 +0000 (19:42 -0700)]
Merge tag 'gpio-v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes that I collected since -rc1, nothing
controversial, nothing special:
- fix a memory leak for GPIO hotplug.
- fix a signedness bug in the ACPI GPIO pin validation.
- driver fixes: Qualcomm SPMI and OMAP MPUIO IRQ issues"
* tag 'gpio-v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: Fix regression for MPUIO interrupts
gpio: sysfs: fix memory leaks and device hotplug
pinctrl: qcom-spmi-gpio: Fix input value report
pinctrl: qcom-spmi-gpio: Fix output type configuration
gpiolib: change gpio pin from unsigned to signed in acpi callback
Linus Torvalds [Sat, 9 May 2015 02:34:35 +0000 (19:34 -0700)]
Merge tag 'mmc-4.1-rc2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Don't access RPMB partitions for normal read/write
- Fix hibernation restore sequence
MMC host:
- dw_mmc: Fix card detection for non removable cards
- dw_mmc: Fix sglist issue in 32-bit mode
- sh_mmcif: Fix timeout value for command request"
* tag 'mmc-4.1-rc2' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
mmc: card: Don't access RPMB partitions for normal read/write
mmc: sh_mmcif: Fix timeout value for command request
mmc: core: add missing pm event in mmc_pm_notify to fix hib restore
Linus Torvalds [Sat, 9 May 2015 01:22:05 +0000 (18:22 -0700)]
Merge tag 'trace-fixes-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"The newly added ftrace_print_array_seq() function had a bug in it.
Luckily, the only user of it didn't make the 4.1 merge window.
But the helper function should be fixed before 4.2 when the users
start coming in"
* tag 'trace-fixes-v4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Make ftrace_print_array_seq compute buf_len
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle are failing on Exynos5250 Snow.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Markus Reichl [Fri, 8 May 2015 18:05:51 +0000 (03:05 +0900)]
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
The Exynos4412 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-X2/U2/U3 boards.
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
Commit ea08de16eb1b ("ARM: dts: Add DISP1 power domain for exynos5420")
added a device node for the Exynos5420 DISP1 power domain but dit not
make the DP controller a consumer of that power domain.
This causes an "Unhandled fault: imprecise external abort" error if the
exynos-dp driver tries to access the DP controller registers and the PD
was turned off. This lead to a kernel panic and a complete system hang.
Make the DP controller device node a consumer of the DISP1 power domain
to ensure that the PD is turned on when the exynos-dp driver is probed.
Fixes: ea08de16eb1b ("ARM: dts: Add DISP1 power domain for exynos5420") Signed-off-by: Javier Martinez Canillas <[email protected]> Signed-off-by: Kukjin Kim <[email protected]>
MAINTAINERS: socfpga: update the git repo for SoCFPGA
The git tree at rocketboards.org is going away. Update the entry to reflect
the address of the new location. Also add an entry for all the socfpga_*
dts files.
Mario Kleiner [Mon, 4 May 2015 04:29:44 +0000 (06:29 +0200)]
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
Tegra would not only need a hardware vblank counter that
increments at leading edge of vblank, but also support
for instantaneous high precision vblank timestamp queries, ie.
a proper implementation of dev->driver->get_vblank_timestamp().
Without these, there can be off-by-one errors during vblank
disable/enable if the scanout is inside vblank at en/disable
time, and additionally clients will never see any useable
vblank timestamps when querying via drmWaitVblank ioctl. This
would negatively affect swap scheduling under X11 and Wayland.
Dave Airlie [Fri, 8 May 2015 10:52:51 +0000 (20:52 +1000)]
Merge tag 'drm-amdkfd-fixes-2015-05-07' of git://people.freedesktop.org/~gabbayo/linux into drm-fixes
- Add missing initialization of SDMA vm register when creating an SDMA queue
- Don't report local memory size, as we don't support local memory allocation
yet.
- Allow to unregister process with exisiting queues. Until now we blocked
it with BUG_ON, which was also an error by itself.
* tag 'drm-amdkfd-fixes-2015-05-07' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Initialize sdma vm when creating sdma queue
drm/amdkfd: Don't report local memory size
drm/amdkfd: allow unregister process with queues
Dave Airlie [Fri, 8 May 2015 10:52:21 +0000 (20:52 +1000)]
Merge branch 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Mostly stability fixes for UVD and VCE, plus a few other bug and regression
fixes.
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
drm/radeon: make UVD handle checking more strict
drm/radeon: make VCE handle check more strict
drm/radeon: fix userptr lockup
drm/radeon: fix userptr BO unpin bug v3
drm/radeon: don't setup audio on asics that don't support it
drm/radeon: disable semaphores for UVD V1 (v2)
Fixes: a0840e2e165a ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.") Signed-off-by: Tommi Rantala <[email protected]> Acked-by: Julian Anastasov <[email protected]> Signed-off-by: Simon Horman <[email protected]>
NeilBrown [Fri, 8 May 2015 08:19:40 +0000 (18:19 +1000)]
md/raid5: fix handling of degraded stripes in batches.
There is no need for special handling of stripe-batches when the array
is degraded.
There may be if there is a failure in the batch, but STRIPE_DEGRADED
does not imply an error.
So don't set STRIPE_BATCH_ERR in ops_run_io just because the array is
degraded.
This actually causes a bug: the STRIPE_DEGRADED flag gets cleared in
check_break_stripe_batch_list() and so the bitmap bit gets cleared
when it shouldn't.
So in check_break_stripe_batch_list(), split the batch up completely -
again STRIPE_DEGRADED isn't meaningful.
Also don't set STRIPE_BATCH_ERR when there is a write error to a
replacement device. This simply removes the replacement device and
requires no extra handling.
NeilBrown [Fri, 8 May 2015 08:19:39 +0000 (18:19 +1000)]
md/raid5: fix allocation of 'scribble' array.
As the new 'scribble' array is sized based on chunk size,
we need to make sure the size matches the largest of 'old'
and 'new' chunk sizes when the array is undergoing reshape.
We also potentially need to resize it even when not resizing
the stripe cache, as chunk size can change without changing
number of devices.
So move the 'resize' code into a separate function, and
consider old and new sizes when allocating.
Signed-off-by: NeilBrown <[email protected]> Fixes: 46d5b785621a ("raid5: use flex_array for scribble data")
NeilBrown [Fri, 8 May 2015 08:19:34 +0000 (18:19 +1000)]
md/raid5: don't record new size if resize_stripes fails.
If any memory allocation in resize_stripes fails we will return
-ENOMEM, but in some cases we update conf->pool_size anyway.
This means that if we try again, the allocations will be assumed
to be larger than they are, and badness results.
So only update pool_size if there is no error.
This bug was introduced in 2.6.17 and the patch is suitable for
-stable.
Fixes: ad01c9e3752f ("[PATCH] md: Allow stripes to be expanded in preparation for expanding an array") Cc: [email protected] (v2.6.17+) Signed-off-by: NeilBrown <[email protected]>
NeilBrown [Fri, 8 May 2015 08:19:32 +0000 (18:19 +1000)]
md/raid5: more incorrect BUG_ON in handle_stripe_fill.
It is not incorrect to call handle_stripe_fill() when
a batch of full-stripe writes is active.
It is, however, a BUG if fetch_block() then decides
it needs to actually fetch anything.
md-raid0: conditional mddev->queue access to suit dm-raid
This patch is a prerequisite for dm-raid "raid0" support to allow
dm-raid to access the MD RAID0 personality doing unconditional
accesses to mddev->queue, which is NULL in case of dm-raid stacked on
top of MD.
Most of the conditional mddev->queue accesses made it to upstream but
this missing one, which prohibits md raid0 to set disk stack limits
(being done in dm core in case of md underneath dm).
Linus Torvalds [Thu, 7 May 2015 22:58:00 +0000 (15:58 -0700)]
Merge tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These include three regression fixes (PCI resources management,
ACPI/PNP device enumeration, ACPI SBS on MacBook) and two ACPI
documentation fixes related to GPIO.
Specifics:
- Fix for a PCI resources management regression introduced during the
4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu)
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge)
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik)
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
Nicolas Ferre [Wed, 29 Apr 2015 09:57:18 +0000 (11:57 +0200)]
MAINTAINERS: replace an AT91 maintainer
As some help is needed from an active maintainer, replace Andrew Victor
by Alexandre Belloni in the ARM/Atmel MAINTAINERS' entry (aka AT91).
Add an entry to the CREDITS file.
Thanks Andrew for the great role you played during the early days of this
product family.
Mark Salter [Tue, 28 Apr 2015 17:09:32 +0000 (13:09 -0400)]
drivers: CCI: fix used_mask init in validate_group()
Currently in validate_group(), there is a static initializer
for fake_pmu.used_mask which is based on CPU_BITS_NONE but
the used_mask array size is based on CCI_PMU_MAX_HW_EVENTS.
CCI_PMU_MAX_HW_EVENTS is not based on NR_CPUS, so CPU_BITS_NONE
is not correct and will cause a build failure if NR_CPUS
is set high enough to make CPU_BITS_NONE larger than used_mask.
Arnd Bergmann [Thu, 7 May 2015 16:28:04 +0000 (18:28 +0200)]
Merge tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
Merge "Ux500 fixes" from Linus Walleij:
This fixes an MMC/SD configuration issue present for some time
in the Ux500 DT but triggered by proper error handling in v4.1-rc1.
* tag 'stericsson-fixes-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable GPIO regulator for SD-card for snowball
ARM: ux500: Enable GPIO regulator for SD-card for HREF boards
ARM: ux500: Move GPIO regulator for SD-card into board DTSs
Arnd Bergmann [Thu, 7 May 2015 16:25:38 +0000 (18:25 +0200)]
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
Arnd Bergmann [Thu, 7 May 2015 16:24:32 +0000 (18:24 +0200)]
Merge tag 'arm-soc/for-4.1/maintainers' of http://github.com/broadcom/stblinux into fixes
Merge "MAINTAINERS update for Broadcom SoCs for 4.1 #2" from Florian Fainelli:
This pull request contains 3 changes to the MAINTAINERS file for Broadcom SoCs:
- add Ray and Scott for mach-bcm
- remove Christian for mach-bcm
- remove Marc for brcmstb
* tag 'arm-soc/for-4.1/maintainers' of http://github.com/broadcom/stblinux:
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
MAINTAINERS: Update mach-bcm maintainers list
Arnd Bergmann [Thu, 7 May 2015 16:23:00 +0000 (18:23 +0200)]
Merge tag 'fixes-for-v4.1-rc2' of https://github.com/rjarzmik/linux into fixes
Merged "ARM: pxa: fixes for v4.1-rc2" from Robert Jarzmik:
These fixes reenable the lubbock(pxa25x) and mainstone(pxa27x)
platforms, which were broken since the gpio handling was
converted to a driver, and the interrupt ordering broke the
external interrupts of these systems.
* tag 'fixes-for-v4.1-rc2' of https://github.com/rjarzmik/linux:
ARM: pxa: lubbock: use new pxa_cplds driver
ARM: pxa: mainstone: use new pxa_cplds driver
ARM: pxa: pxa_cplds: add lubbock and mainstone IO
Arnd Bergmann [Thu, 7 May 2015 16:21:57 +0000 (18:21 +0200)]
Merge tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.1" from Shawn Guo:
- A couple of imx23-olinuxino device tree fixes regarding to LED GPIO
polarity and USB dr_mode setting
- One i.MX28 device tree fix on AUART4 TX-DMA interrupt name
- Add missing pwm-cells to PWM4 for i.MX25 device tree
- Fix imx6q-phytec device tree to get correct USB VBUS control
- Drop invalid pinctrl-assert-gpios property from imx6qdl-sabreauto
device tree, which was sneaked in from vendor device tree
- One fix on Wolfram's broken email address
* tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-sabreauto: remove pinctrl-assert-gpios
ARM: dts: imx28: Fix AUART4 TX-DMA interrupt name
ARM: dts: imx25: Add #pwm-cells to pwm4
ARM: dts: imx6: phyFLEX: USB VBUS control is active-high
ARM: mach-imx: devices: platform-sdhci-esdhc-imx: fix broken email address
ARM: dts: imx23-olinuxino: Fix dr_mode of usb0
ARM: dts: imx23-olinuxino: Fix polarity of LED GPIO
Arnd Bergmann [Thu, 7 May 2015 16:19:27 +0000 (18:19 +0200)]
Merge tag 'v4.1-rockchip-socfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: some soc-level fixes for 4.1" from Heiko Stübner:
Two fixes from Chris Zhong, fixing some suspend oddities.
And I've given up on the timer7 issue. While I initially thought
devices would either have both the grave mmu issue requiring a uboot
update and the timer7 issue or none, it looks like in all units in the
field the mmu issue got fixed while the timer7 issue stayed on.
So instead of making everybody wanting to use mainline jump through a
hoop just make sure timer7 is on on boot before we init the arch-timer.
* tag 'v4.1-rockchip-socfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
rockchip: make sure timer7 is enabled on rk3288 platforms
ARM: rockchip: fix undefined instruction of reset_ctrl_regs
ARM: rockchip: disable dapswjdp during suspend
Linus Torvalds [Thu, 7 May 2015 15:27:38 +0000 (08:27 -0700)]
Merge tag 'pinctrl-v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a smallish set of pin control fixes for the v4.1 cycle,
collected the last two weeks:
- fix a real nasty legacy bug that has screwed up the protection of
adding pinctrl maps dynamically. Normally this didn't happen so
much but Dough Anderson ran into it and fixed it, kudos!
- minor driver fixes for Qualcomm spmi, mediatek and Marvell drivers"
* tag 'pinctrl-v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: Don't just pretend to protect pinctrl_maps, do it for real
pinctrl: mediatek: mtk-common: initialize unmask
pinctrl: qcom-spmi-mpp: Fix input value report
pinctrl: qcom-spmi: Fix pin direction configuration
pinctrl: mvebu: Fix mapping of pin 63 (gpo -> gpio)
Oded Gabbay [Tue, 5 May 2015 08:15:07 +0000 (11:15 +0300)]
drm/amdkfd: Don't report local memory size
This patch sets the local memory size that is reported to userspace to 0.
This is done to make sure that userspace won't try to allocate local memory
for HSA.
As long as amdkfd doesn't support allocating local memory for HSA,
we need this patch.
Sometimes we might unregister process that have queues, because we couldn't
preempt the queues. Until now we blocked it with BUG_ON but instead just
print it as debug.
Linus Torvalds [Thu, 7 May 2015 14:04:33 +0000 (07:04 -0700)]
Merge tag 'for-linus' of git://github.com/dledford/linux
Pull infiniband updates from Doug Ledford:
"Minor updates for 4.1-rc
Most of the changes are fairly small and well confined. The iWARP
address reporting changes are the only ones that are a medium size. I
had these queued up prior to rc1, but due to the shuffle in
maintainers, they did not get submitted when I expected. My apologies
for that. I feel comfortable with them however due to the testing
they've received, so I left them in this submission"
* tag 'for-linus' of git://github.com/dledford/linux:
MAINTAINERS: Update InfiniBand subsystem maintainer
MAINTAINERS: add include/rdma/ to InfiniBand subsystem
IPoIB/CM: Fix indentation level
iw_cxgb4: Remove negative advice dmesg warnings
IB/core: Fix unaligned accesses
IB/core: change rdma_gid2ip into void function as it always return zero
IB/qib: use arch_phys_wc_add()
IB/qib: add acounting for MTRR
IB/core: dma unmap optimizations
IB/core: dma map/unmap locking optimizations
RDMA/cxgb4: Report the actual address of the remote connecting peer
RDMA/nes: Report the actual address of the remote connecting peer
RDMA/core: Enable the iWarp Port Mapper to provide the actual address of the connecting peer to its clients
iw_cxgb4: enforce qp/cq id requirements
iw_cxgb4: use BAR2 GTS register for T5 kernel mode CQs
iw_cxgb4: 32b platform fixes
iw_cxgb4: Cleanup register defines/MACROS
RDMA/CMA: Canonize IPv4 on IPV6 sockets properly
Chris Wilson [Thu, 7 May 2015 10:16:26 +0000 (11:16 +0100)]
drm/i915: Drop PIPE-A quirk for 945GSE HP Mini
Since the introduction of BIOS fb preservation, circa 3.17, we began
encountering a failure during boot when trying to use force-detect
before GEM was initialised. That bug is from
drm/i915: ensure the force pipe A quirk is actually followed
but investigation of the affected machine revealed that it was using a
PIPE-A quirk even though it was a 945GSE and the quirk is only supposed
to be used to workaround a hardware issue on 830/845. That quirk was
added for this HP Mini in
in order to workaround an issue with the BIOS behaving strangely during
lid-close. Since then we have a much larger hammer to thwart the BIOS
after opening the lid and the PIPE-A quirk is no longer required.
Reported-and-tested-by: Apostolos B. <[email protected]>
References: https://bugs.freedesktop.org/show_bug.cgi?id=21960
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=87521 Signed-off-by: Chris Wilson <[email protected]> Signed-off-by: Jani Nikula <[email protected]>
igb: Fix NULL assignment to incorrect variable in igb_reset_q_vector
adapter->tx_ring is set to NULL where rx_ring should be.
Fixes: 5536d2102a2d ("igb: Combine q_vector and ring allocation into a single function") Signed-off-by: Toshiaki Makita <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
When changing the number of rings by ethtool -L, q_vectors are reused,
which causes oops because of uninitialized pointers.
- When an rx is reused as a tx, q_vector->rx.ring is not set to NULL, which
misleads igb_poll() to determine that it has an rx ring although it
actually points to the tx ring.
- When a tx is reused as an rx, q_vector->rx.ring->skb
(q_vector->ring[0].skb) has a value that was used as tx_stats before.
Fix these problems by zeroing it out on reuseing it.
Fixes: 02ef6e1d0b00 ("igb: Fix queue allocation method to accommodate changing during runtime") Signed-off-by: Toshiaki Makita <[email protected]> Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>
Sonika Jindal [Thu, 7 May 2015 08:29:28 +0000 (13:59 +0530)]
drm/i915: Sink rate read should be saved in deca-kHz
The sink rate read from supported link rate table is in KHz as per spec
while in drm, the saved clock is in deca-KHz. So divide the link rate by
10 before storing.
Reading of rates was added by:
commit fc0f8e25318f ("drm/i915/skl: Read sink supported rates from edp
panel")
tracing: Make ftrace_print_array_seq compute buf_len
The only caller to this function (__print_array) was getting it wrong by
passing the array length instead of buffer length. As the element size
was already being passed for other reasons it seems reasonable to push
the calculation of buffer length into the function.
Linus Torvalds [Wed, 6 May 2015 22:58:06 +0000 (15:58 -0700)]
Merge tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix blkback regression if using persistent grants
- fix various event channel related suspend/resume bugs
- fix AMD x86 regression with X86_BUG_SYSRET_SS_ATTRS
- SWIOTLB on ARM now uses frames <4 GiB (if available) so device only
capable of 32-bit DMA work.
* tag 'for-linus-4.1b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
hypervisor/x86/xen: Unset X86_BUG_SYSRET_SS_ATTRS on Xen PV guests
xen/events: Set irq_info->evtchn before binding the channel to CPU in __startup_pirq()
xen/console: Update console event channel on resume
xen/xenbus: Update xenbus event channel on resume
xen/events: Clear cpu_evtchn_mask before resuming
xen-pciback: Add name prefix to global 'permissive' variable
xen: Suspend ticks on all CPUs during suspend
xen/grant: introduce func gnttab_unmap_refs_sync()
xen/blkback: safely unmap purge persistent grants
Linus Torvalds [Wed, 6 May 2015 17:57:37 +0000 (10:57 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"EFI fixes, and FPU fix, a ticket spinlock boundary condition fix and
two build fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Always restore_xinit_state() when use_eager_cpu()
x86: Make cpu_tss available to external modules
efi: Fix error handling in add_sysfs_runtime_map_entry()
x86/spinlocks: Fix regression in spinlock contention detection
x86/mm: Clean up types in xlate_dev_mem_ptr()
x86/efi: Store upper bits of command line buffer address in ext_cmd_line_ptr
efivarfs: Ensure VariableName is NUL-terminated
Linus Torvalds [Wed, 6 May 2015 17:47:25 +0000 (10:47 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also an uncore PMU driver fix and an uncore
PMU driver hardware-enablement addition"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Fix segfault if passed with ''.
perf report: Fix -T/--threads option to work again
perf bench numa: Fix immediate meeting of convergence condition
perf bench numa: Fixes of --quiet argument
perf bench futex: Fix hung wakeup tasks after requeueing
perf probe: Fix bug with global variables handling
perf top: Fix a segfault when kernel map is restricted.
tools lib traceevent: Fix build failure on 32-bit arch
perf kmem: Fix compiles on RHEL6/OL6
tools lib api: Undefine _FORTIFY_SOURCE before setting it
perf kmem: Consistently use PRIu64 for printing u64 values
perf trace: Disable events and drain events when forked workload ends
perf trace: Enable events when doing system wide tracing and starting a workload
perf/x86/intel/uncore: Move PCI IDs for IMC to uncore driver
perf/x86/intel/uncore: Add support for Intel Haswell ULT (lower power Mobile Processor) IMC uncore PMUs
perf/x86/intel: Add cpu_(prepare|starting|dying) for core_pmu
Using sendfile with below small program to get MD5 sums of some files,
it appear that big files (over 64kbytes with 4k pages system) get a
wrong MD5 sum while small files get the correct sum.
This program uses sendfile() to send a file to an AF_ALG socket
for hashing.
After investivation, it appears that sendfile() sends the files by blocks
of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each
block, the SPLICE_F_MORE flag is missing, therefore the hashing operation
is reset as if it was the end of the file.
This patch adds SPLICE_F_MORE to the flags when more data is pending.
Doug Anderson [Fri, 1 May 2015 16:01:27 +0000 (09:01 -0700)]
pinctrl: Don't just pretend to protect pinctrl_maps, do it for real
Way back, when the world was a simpler place and there was no war, no
evil, and no kernel bugs, there was just a single pinctrl lock. That
was how the world was when (57291ce pinctrl: core device tree mapping
table parsing support) was written. In that case, there were
instances where the pinctrl mutex was already held when
pinctrl_register_map() was called, hence a "locked" parameter was
passed to the function to indicate that the mutex was already locked
(so we shouldn't lock it again).
A few years ago in (42fed7b pinctrl: move subsystem mutex to
pinctrl_dev struct), we switched to a separate pinctrl_maps_mutex.
...but (oops) we forgot to re-think about the whole "locked" parameter
for pinctrl_register_map(). Basically the "locked" parameter appears
to still refer to whether the bigger pinctrl_dev mutex is locked, but
we're using it to skip locks of our (now separate) pinctrl_maps_mutex.
That's kind of a bad thing(TM). Probably nobody noticed because most
of the calls to pinctrl_register_map happen at boot time and we've got
synchronous device probing. ...and even cases where we're
asynchronous don't end up actually hitting the race too often. ...but
after banging my head against the wall for a bug that reproduced 1 out
of 1000 reboots and lots of looking through kgdb, I finally noticed
this.
Anyway, we can now safely remove the "locked" parameter and go back to
a war-free, evil-free, and kernel-bug-free world.
Fixes: 42fed7ba44e4 ("pinctrl: move subsystem mutex to pinctrl_dev struct") Signed-off-by: Doug Anderson <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
xen: Add __GFP_DMA flag when xen_swiotlb_init gets free pages on ARM
Make sure that xen_swiotlb_init allocates buffers that are DMA capable
when at least one memblock is available below 4G. Otherwise we assume
that all devices on the SoC can cope with >4G addresses. We do this on
ARM and ARM64, where dom0 is mapped 1:1, so pfn == mfn in this case.
Tony Lindgren [Thu, 23 Apr 2015 23:54:17 +0000 (16:54 -0700)]
gpio: omap: Fix regression for MPUIO interrupts
At some point with all the GPIO clean-up we've broken the
MPUIO interrupts. Those are just a little bit different from
the GPIO interrupts, so we can fix it up just by setting
different irqchip functions for it. And then we can just
remove all old code trying to do the same.
Chuanxiao Dong [Tue, 12 Aug 2014 04:01:30 +0000 (12:01 +0800)]
mmc: card: Don't access RPMB partitions for normal read/write
During kernel boot, it will try to read some logical sectors
of each block device node for the possible partition table.
But since RPMB partition is special and can not be accessed
by normal eMMC read / write CMDs, it will cause below error
messages during kernel boot:
...
mmc0: Got data interrupt 0x00000002 even though no data operation was in progress.
mmcblk0rpmb: error -110 transferring data, sector 0, nr 32, cmd response 0x900, card status 0xb00
mmcblk0rpmb: retrying using single block read
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900
end_request: I/O error, dev mmcblk0rpmb, sector 0
Buffer I/O error on device mmcblk0rpmb, logical block 0
end_request: I/O error, dev mmcblk0rpmb, sector 8
Buffer I/O error on device mmcblk0rpmb, logical block 1
end_request: I/O error, dev mmcblk0rpmb, sector 16
Buffer I/O error on device mmcblk0rpmb, logical block 2
end_request: I/O error, dev mmcblk0rpmb, sector 24
Buffer I/O error on device mmcblk0rpmb, logical block 3
...
This patch will discard the access request in eMMC queue if
it is RPMB partition access request. By this way, it avoids
trigger above error messages.
mmc: sh_mmcif: Fix timeout value for command request
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.
Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.
Fixes: f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout") Signed-off-by: Takeshi Kihara <[email protected]>
[horms: rewrote changelog to refer to HZ] Signed-off-by: Simon Horman <[email protected]> Signed-off-by: Yoshihiro Kaneko <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
Bobby Powers [Mon, 27 Apr 2015 15:10:41 +0000 (08:10 -0700)]
x86/fpu: Always restore_xinit_state() when use_eager_cpu()
The following commit:
f893959b0898 ("x86/fpu: Don't abuse drop_init_fpu() in flush_thread()")
removed drop_init_fpu() usage from flush_thread(). This seems to break
things for me - the Go 1.4 test suite fails all over the place with
floating point comparision errors (offending commit found through
bisection).
The functional change was that flush_thread() after this commit
only calls restore_init_xstate() when both use_eager_fpu() and
!used_math() are true. drop_init_fpu() (now fpu_reset_state()) calls
restore_init_xstate() regardless of whether current used_math() - apply
the same logic here.
Switch used_math() -> tsk_used_math(tsk) to consistently use the grabbed
tsk instead of current, like in the rest of flush_thread().
Jani Nikula [Tue, 5 May 2015 13:32:12 +0000 (16:32 +0300)]
drm/i915/dp: there is no audio on port A
The eDP port A register on PCH split platforms has a slightly different
register layout from the other ports, with bit 6 being either alternate
scrambler reset or reserved, depending on the generation. Our
misinterpretation of the bit as audio has lead to warning.
Fix this by not enabling audio on port A, since none of our platforms
support audio on port A anyway.
v2: DDI doesn't have audio on port A either (Sivakumar Thulasimani)
Linus Torvalds [Wed, 6 May 2015 02:42:01 +0000 (19:42 -0700)]
Merge tag 'for-linus-4.1-1' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Lots of minor IPMI fixes, especially ones that have have come up since
the SSIF driver has been in the main kernel for a while"
* tag 'for-linus-4.1-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: Fix multi-part message handling
ipmi: Add alert handling to SSIF
ipmi: Fix a problem that messages are not issued in run_to_completion mode
ipmi: Report an error if ACPI _IFT doesn't exist
ipmi: Remove unused including <linux/version.h>
ipmi: Don't report err in the SI driver for SSIF devices
ipmi: Remove incorrect use of seq_has_overflowed
ipmi:ssif: Ignore spaces when comparing I2C adapter names
ipmi_ssif: Fix the logic on user-supplied addresses
Linus Torvalds [Wed, 6 May 2015 01:52:13 +0000 (18:52 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 patches
This includes a new rtc driver for the Abracon AB x80x and isn't very
appropriate for -rc2. It was still being fiddled with a bit during
the merge window and I fell asleep during -rc1"
[ So I took the new driver, it seems small and won't regress anything.
I'm a softy. - Linus ]
* emailed patches from Andrew Morton <[email protected]>:
rtc: armada38x: fix concurrency access in armada38x_rtc_set_time
ocfs2: dlm: fix race between purge and get lock resource
nilfs2: fix sanity check of btree level in nilfs_btree_root_broken()
util_macros.h: have array pointer point to array of constants
configfs: init configfs module earlier at boot time
mm/hwpoison-inject: check PageLRU of hpage
mm/hwpoison-inject: fix refcounting in no-injection case
mm: soft-offline: fix num_poisoned_pages counting on concurrent events
rtc: add rtc-abx80x, a driver for the Abracon AB x80x i2c rtc
Documentation: bindings: add abracon,abx80x
kasan: show gcc version requirements in Kconfig and Documentation
mm/memory-failure: call shake_page() when error hits thp tail page
lib: delete lib/find_last_bit.c
MAINTAINERS: add co-maintainer for LED subsystem
zram: add Designated Reviewer for zram in MAINTAINERS
revert "zram: move compact_store() to sysfs functions area"
Linus Torvalds [Wed, 6 May 2015 01:14:04 +0000 (18:14 -0700)]
Merge tag 'platform-drivers-x86-v4.1-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"This includes a trivial warning and adding a Lenovo laptop to an
existing quirk.
I've held off on things like the latter in the past, but I didn't feel
it was risky enough to push out to 4.2.
- thinkpad_acpi:
Fix warning for static not at beginning
- ideapad_laptop:
Add Lenovo G40-30 to devices without radio switch"
* tag 'platform-drivers-x86-v4.1-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
thinkpad_acpi: Fix warning for static not at beginning
ideapad_laptop: Add Lenovo G40-30 to devices without radio switch
The values was not being re-initialized, if something went wrong
handling a multi-part message and it got left in a bad state, it
might be an issue.
The commands were not correct when issuing multi-part reads, the
code was not passing in the proper value for commands. Also clean
up some minor formatting issues.
Get the block number from the right location, limit the maximum send
message size to 63 bytes and explain why, and fix some minor sylistic
issues.
The SSIF interface can optionally have an SMBus alert come in when
data is ready. Unfortunately, the IPMI spec gives wiggle room to
the implementer to allow them to always have the alert enabled,
even if the driver doesn't enable it. So implement alerts.
If you don't in this situation, the SMBus alert handling will
constantly complain.
ipmi: Fix a problem that messages are not issued in run_to_completion mode
start_next_msg() issues a message placed in smi_info->waiting_msg
if it is non-NULL. However, sender() sets a message to
smi_info->curr_msg and NULL to smi_info->waiting_msg in the context
of run_to_completion mode. As the result, it leads an infinite
loop by waiting the completion of unissued message when leaving
dying message after kernel panic.
sender() should set the message to smi_info->waiting_msg not
curr_msg.
Gregory CLEMENT [Tue, 5 May 2015 23:24:05 +0000 (16:24 -0700)]
rtc: armada38x: fix concurrency access in armada38x_rtc_set_time
While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms. This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value. This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.
The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.
Junxiao Bi [Tue, 5 May 2015 23:24:02 +0000 (16:24 -0700)]
ocfs2: dlm: fix race between purge and get lock resource
There is a race window in dlm_get_lock_resource(), which may return a
lock resource which has been purged. This will cause the process to
hang forever in dlmlock() as the ast msg can't be handled due to its
lock resource not existing.
dlm_get_lock_resource {
...
spin_lock(&dlm->spinlock);
tmpres = __dlm_lookup_lockres_full(dlm, lockid, namelen, hash);
if (tmpres) {
spin_unlock(&dlm->spinlock);
>>>>>>>> race window, dlm_run_purge_list() may run and purge
the lock resource
spin_lock(&tmpres->spinlock);
...
spin_unlock(&tmpres->spinlock);
}
}
Ryusuke Konishi [Tue, 5 May 2015 23:24:00 +0000 (16:24 -0700)]
nilfs2: fix sanity check of btree level in nilfs_btree_root_broken()
The range check for b-tree level parameter in nilfs_btree_root_broken()
is wrong; it accepts the case of "level == NILFS_BTREE_LEVEL_MAX" even
though the level is limited to values in the range of 0 to
(NILFS_BTREE_LEVEL_MAX - 1).
Since the level parameter is read from storage device and used to index
nilfs_btree_path array whose element count is NILFS_BTREE_LEVEL_MAX, it
can cause memory overrun during btree operations if the boundary value
is set to the level parameter on device.
This fixes the broken sanity check and adds a comment to clarify that
the upper bound NILFS_BTREE_LEVEL_MAX is exclusive.
Guenter Roeck [Tue, 5 May 2015 23:23:57 +0000 (16:23 -0700)]
util_macros.h: have array pointer point to array of constants
Using the new find_closest() macro can result in the following sparse
warnings.
drivers/hwmon/lm85.c:194:16: warning:
incorrect type in initializer (different modifiers)
drivers/hwmon/lm85.c:194:16: expected int *__fc_a
drivers/hwmon/lm85.c:194:16: got int static const [toplevel] *<noident>
drivers/hwmon/lm85.c:210:16: warning:
incorrect type in initializer (different modifiers)
drivers/hwmon/lm85.c:210:16: expected int *__fc_a
drivers/hwmon/lm85.c:210:16: got int const *map
This is because the array passed to find_closest() will typically be
declared as array of constants, but the macro declares a non-constant
pointer to it.
Naoya Horiguchi [Tue, 5 May 2015 23:23:52 +0000 (16:23 -0700)]
mm/hwpoison-inject: check PageLRU of hpage
Hwpoison injector checks PageLRU of the raw target page to find out
whether the page is an appropriate target, but current code now filters
out thp tail pages, which prevents us from testing for such cases via this
interface. So let's check hpage instead of p.
projects / linux.git / log