Andy Lutomirski [Wed, 14 Mar 2018 05:03:11 +0000 (22:03 -0700)]
selftests/x86/entry_from_vm86: Add test cases for POPF
POPF is currently broken -- add tests to catch the error. This
results in:
[RUN] POPF with VIP set and IF clear from vm86 mode
[INFO] Exited vm86 mode due to STI
[FAIL] Incorrect return reason (started at eip = 0xd, ended at eip = 0xf)
because POPF currently fails to check IF before reporting a pending
interrupt.
This patch also makes the FAIL message a bit more informative.
Colin Ian King [Mon, 5 Feb 2018 14:08:52 +0000 (14:08 +0000)]
libnvdimm: remove redundant assignment to pointer 'dev'
Pointer dev is being assigned a value that is never read, it is being
re-assigned the same value later on, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
drivers/nvdimm/pfn_devs.c:307:17: warning: Value stored to 'dev' during
its initialization is never read
Paul Mackerras [Wed, 7 Mar 2018 11:17:20 +0000 (22:17 +1100)]
KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry
This fixes a bug where the trap number that is returned by
__kvmppc_vcore_entry gets corrupted. The effect of the corruption
is that IPIs get ignored on POWER9 systems when the IPI is sent via
a doorbell interrupt to a CPU which is executing in a KVM guest.
The effect of the IPI being ignored is often that another CPU locks
up inside smp_call_function_many() (and if that CPU is holding a
spinlock, other CPUs then lock up inside raw_spin_lock()).
The trap number is currently held in register r12 for most of the
assembly-language part of the guest exit path. In that path, we
call kvmppc_subcore_exit_guest(), which is a C function, without
restoring r12 afterwards. Depending on the kernel config and the
compiler, it may modify r12 or it may not, so some config/compiler
combinations see the bug and others don't.
To fix this, we arrange for the trap number to be stored on the
stack from the 'guest_bypass:' label until the end of the function,
then the trap number is loaded and returned in r12 as before.
Cc: [email protected] # v4.8+ Fixes: fd7bacbca47a ("KVM: PPC: Book3S HV: Fix TB corruption in guest exit path on HMI interrupt") Signed-off-by: Paul Mackerras <[email protected]>
Memory state around the buggy address: ffff880066b99180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff880066b99200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff880066b99280: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff880066b99300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff880066b99380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Arvind Yadav [Tue, 6 Mar 2018 10:05:43 +0000 (15:35 +0530)]
workqueue: use put_device() instead of kfree()
Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized in this function instead.
Mike Snitzer [Mon, 12 Mar 2018 23:49:25 +0000 (19:49 -0400)]
dm mpath: eliminate need to use scsi_device_from_queue
Instead of scsi_device_from_queue(), use scsi_dh_attached_handler_name()
-- whose implementation uses scsi_device_from_queue() to avoid trying to
access SCSI-specific resources from non-SCSI devices.
drivers/auxdisplay/img-ascii-lcd.c: warning: 'err' may be used
uninitialized in this function [-Wuninitialized]
At lines 109 and 207. Reported by Geert using the build service
several times, e.g.:
https://lkml.org/lkml/2018/2/19/303
They are two false positives, since num_chars > 0 in the three present
configurations (boston, malta, sead3). Initialize to 0 in order to
silence the warning.
Miguel Ojeda [Mon, 19 Feb 2018 15:14:17 +0000 (16:14 +0100)]
auxdisplay: img-ascii-lcd: Fix doc comment to silence warnings
Compiling with W=1 with gcc 7.2.0 gives 2 warnings:
drivers/auxdisplay/img-ascii-lcd.c:233: warning: Function parameter or
member 't' not described in 'img_ascii_lcd_scroll'
drivers/auxdisplay/img-ascii-lcd.c:233: warning: Excess function
parameter 'arg' description in 'img_ascii_lcd_scroll'
Miguel Ojeda [Mon, 19 Feb 2018 15:02:48 +0000 (16:02 +0100)]
auxdisplay: panel: Change comments to silence fallthrough warnings
Compiling with W=1 with gcc 7.2.0 gives 3 warnings like:
drivers/auxdisplay/panel.c: In function ‘panel_process_inputs’:
drivers/auxdisplay/panel.c:1374:17: warning: this statement may fall
through [-Wimplicit-fallthrough=]
Dan Carpenter [Tue, 13 Mar 2018 09:09:38 +0000 (12:09 +0300)]
qed: Use after free in qed_rdma_free()
We're dereferencing "p_hwfn->p_rdma_info" but that is freed on the line
before in qed_rdma_resc_free(p_hwfn).
Fixes: 9de506a547c0 ("qed: Free RoCE ILT Memory on rmmod qedr") Signed-off-by: Dan Carpenter <[email protected]> Acked-by: Michal Kalderon <[email protected]> Signed-off-by: David S. Miller <[email protected]>
1) Refuse to insert 32 bit userspace socket policies on 64
bit systems like we do it for standard policies. We don't
have a compat layer, so inserting socket policies from
32 bit userspace will lead to a broken configuration.
2) Make the policy hold queue work without the flowcache.
Dummy bundles are not chached anymore, so we need to
generate a new one on each lookup as long as the SAs
are not yet in place.
3) Fix the validation of the esn replay attribute. The
The sanity check in verify_replay() is bypassed if
the XFRM_STATE_ESN flag is not set. Fix this by doing
the sanity check uncoditionally.
From Florian Westphal.
4) After most of the dst_entry garbage collection code
is removed, we may leak xfrm_dst entries as they are
neither cached nor tracked somewhere. Fix this by
reusing the 'uncached_list' to track xfrm_dst entries
too. From Xin Long.
5) Fix a rcu_read_lock/rcu_read_unlock imbalance in
xfrm_get_tos() From Xin Long.
6) Fix an infinite loop in xfrm_get_dst_nexthop. On
transport mode we fetch the child dst_entry after
we continue, so this pointer is never updated.
Fix this by fetching it before we continue.
7) Fix ESN sequence number gap after IPsec GSO packets.
We accidentally increment the sequence number counter
on the xfrm_state by one packet too much in the ESN
case. Fix this by setting the sequence number to the
correct value.
8) Reset the ethernet protocol after decapsulation only if a
mac header was set. Otherwise it breaks configurations
with TUN devices. From Yossi Kuperman.
9) Fix __this_cpu_read() usage in preemptible code. Use
this_cpu_read() instead in ipcomp_alloc_tfms().
From Greg Hackmann.
Please pull or let me know if there are problems.
====================
Ard Biesheuvel [Tue, 13 Mar 2018 14:09:21 +0000 (14:09 +0000)]
efi/libstub/tpm: Initialize pointer variables to zero for mixed mode
As reported by Jeremy Cline, running the new TPM libstub code in mixed
mode (i.e., 64-bit kernel on 32-bit UEFI) results in hangs when invoking
the TCG2 protocol, or when accessing the log_tbl pool allocation.
The reason turns out to be that in both cases, the 64-bit pointer
variables are not fully initialized by the 32-bit EFI code, and so
we should take care to zero initialize these variables beforehand,
or we'll end up dereferencing bogus pointers.
Greg Hackmann [Wed, 7 Mar 2018 22:42:53 +0000 (14:42 -0800)]
net: xfrm: use preempt-safe this_cpu_read() in ipcomp_alloc_tfms()
f7c83bcbfaf5 ("net: xfrm: use __this_cpu_read per-cpu helper") added a
__this_cpu_read() call inside ipcomp_alloc_tfms().
At the time, __this_cpu_read() required the caller to either not care
about races or to handle preemption/interrupt issues. 3.15 tightened
the rules around some per-cpu operations, and now __this_cpu_read()
should never be used in a preemptible context. On 3.15 and later, we
need to use this_cpu_read() instead.
syzkaller reported this leading to the following kernel BUG while
fuzzing sendmsg:
scsi: qla2xxx: Remove FC_NO_LOOP_ID for FCP and FC-NVMe Discovery
Commit 7d64c39e64310 fixed regression of FCP discovery when Nport Handle
is in-use and relogin is triggered. However, during FCP and FC-NVMe
discovery this resulted into only discovering NVMe LUNs.
This patch fixes issue where FCP and FC-NVMe protocol is used on same
port where assigning FC_NO_LOOP_ID will result into discovery failure
for FCP LUNs.
Fixes: a084fd68e1d26 ("scsi: qla2xxx: Fix re-login for Nport Handle in use") Signed-off-by: Himanshu Madhani <[email protected]> Reviewed-by: Hannes Reinecke <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
Jason Yan [Thu, 8 Mar 2018 02:34:53 +0000 (10:34 +0800)]
scsi: libsas: defer ata device eh commands to libata
When ata device doing EH, some commands still attached with tasks are
not passed to libata when abort failed or recover failed, so libata did
not handle these commands. After these commands done, sas task is freed,
but ata qc is not freed. This will cause ata qc leak and trigger a
warning like below:
If ata qc leaked too many, ata tag allocation will fail and io blocked
for ever.
As suggested by Dan Williams, defer ata device commands to libata and
merge sas_eh_finish_cmd() with sas_eh_defer_cmd(). libata will handle
ata qcs correctly after this.
Florian Fainelli [Mon, 12 Mar 2018 23:00:40 +0000 (16:00 -0700)]
net: dsa: Fix dsa_is_user_port() test inversion
During the conversion to dsa_is_user_port(), a condition ended up being
reversed, which would prevent the creation of any user port when using
the legacy binding and/or platform data, fix that.
Fixes: 4a5b85ffe2a0 ("net: dsa: use dsa_is_user_port everywhere") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Wei Yongjun [Thu, 4 Jan 2018 06:34:43 +0000 (06:34 +0000)]
clk: qcom: msm8916: Fix return value check in qcom_apcs_msm8916_clk_probe()
In case of error, the function dev_get_regmap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Jerome Brunet [Wed, 14 Feb 2018 13:43:35 +0000 (14:43 +0100)]
clk: fix determine rate error with pass-through clock
If we try to determine the rate of a pass-through clock (a clock which
does not implement .round_rate() nor .determine_rate()),
clk_core_round_rate_nolock() will directly forward the call to the
parent clock. In the particular case where the pass-through actually
does not have a parent, clk_core_round_rate_nolock() will directly
return 0 with the requested rate still set to the initial request
structure. This is interpreted as if the rate could be exactly achieved
while it actually cannot be adjusted.
This become a real problem when this particular pass-through clock is
the parent of a mux with the flag CLK_SET_RATE_PARENT set. The
pass-through clock will always report an exact match, get picked and
finally error when the rate is actually getting set.
This is fixed by setting the rate inside the req to 0 when core is NULL
in clk_core_round_rate_nolock() (same as in __clk_determine_rate() when
hw is NULL)
Fixes: 0f6cc2b8e94d ("clk: rework calls to round and determine rate callbacks") Signed-off-by: Jerome Brunet <[email protected]> Signed-off-by: Michael Turquette <[email protected]> Signed-off-by: Stephen Boyd <[email protected]>
Stephen Boyd [Mon, 12 Mar 2018 22:07:42 +0000 (15:07 -0700)]
Merge tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm into clk-fixes
Pull TI SoC clock fixes for 4.16 from Tero Kristo:
* tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm:
clk: ti: am43xx: add set-rate-parent support for display clkctrl clock
clk: ti: am33xx: add set-rate-parent support for display clkctrl clock
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
Stephen Boyd [Mon, 12 Mar 2018 22:06:38 +0000 (15:06 -0700)]
Merge tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-fixes
Pull i.MX clock fixes for 4.16 from Shawn Guo:
- Update i.MX5 clock driver to register UART4/5 clock only on i.MX50
and i.MX53. It fixes a kernel warning seen on i.MX53, caused by
commit 59dc3d8c8673 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53").
* tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx51-imx53: Fix UART4/5 registration on i.MX50 and i.MX53
Stephen Boyd [Mon, 12 Mar 2018 22:05:49 +0000 (15:05 -0700)]
Merge tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clock fixes for 4.16 from Chen-Yu Tsai:
A critical fix for the A31 sunxi-ng clock driver. The CLK_OUT clocks
had definitions paired with the incorrect type of clk ops. This results
in a serious oops starting with commit 946797aa3f08 ("clk: sunxi-ng:
Support fixed post-dividers on MP style clocks"), which exposed the
incorrect clk ops when it added a new field to the data structures,
which then nudged the underlying (compatible but incorrect) data
structures out of alignment.
* tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops
David S. Miller [Mon, 12 Mar 2018 19:21:08 +0000 (15:21 -0400)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-03-12
This series contains fixes to e1000e only.
Benjamin Poirier provides two fixes, first reverts commits that changed
what happens to the link status when there is an error. These commits
were to resolve a race condition, but in the process of fixing the race
condition, they changed the behavior when an error occurred. Second fix
resolves a race condition by not setting "get_link_status" to false
after checking the link.
====================
Paolo Abeni [Mon, 12 Mar 2018 13:54:24 +0000 (14:54 +0100)]
l2tp: fix races with ipv4-mapped ipv6 addresses
The l2tp_tunnel_create() function checks for v4mapped ipv6
sockets and cache that flag, so that l2tp core code can
reusing it at xmit time.
If the socket is provided by the userspace, the connection
status of the tunnel sockets can change between the tunnel
creation and the xmit call, so that syzbot is able to
trigger the following splat:
BUG: KASAN: use-after-free in ip6_dst_idev include/net/ip6_fib.h:192
[inline]
BUG: KASAN: use-after-free in ip6_xmit+0x1f76/0x2260
net/ipv6/ip6_output.c:264
Read of size 8 at addr ffff8801bd949318 by task syz-executor4/23448
This change addresses the issues:
* explicitly checking for TCP_ESTABLISHED for user space provided sockets
* dropping the v4mapped flag usage - it can become outdated - and
explicitly invoking ipv6_addr_v4mapped() instead
The issue is apparently there since ancient times.
v1 -> v2: (many thanks to Guillaume)
- with csum issue introduced in v1
- replace pr_err with pr_debug
- fix build issue with IPV6 disabled
- move l2tp_sk_is_v4mapped in l2tp_core.c
v2 -> v3:
- don't update inet_daddr for v4mapped address, unneeded
- drop rendundant check at creation time
Paolo Abeni [Mon, 12 Mar 2018 13:54:23 +0000 (14:54 +0100)]
net: ipv6: keep sk status consistent after datagram connect failure
On unsuccesful ip6_datagram_connect(), if the failure is caused by
ip6_datagram_dst_update(), the sk peer information are cleared, but
the sk->sk_state is preserved.
If the socket was already in an established status, the overall sk
status is inconsistent and fouls later checks in datagram code.
Fix this saving the old peer information and restoring them in
case of failure. This also aligns ipv6 datagram connect() behavior
with ipv4.
v1 -> v2:
- added missing Fixes tag
Fixes: 85cb73ff9b74 ("net: ipv6: reset daddr and dport in sk if connect() fails") Signed-off-by: Paolo Abeni <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Commit 19110cfbb34d ("e1000e: Separate signaling for link check/link up")
changed what happens to the link status when there is an error which
happens after "get_link_status = false" in the copper check_for_link
callbacks. Previously, such an error would be ignored and the link
considered up. After that commit, any error implies that the link is down.
Revert commit 19110cfbb34d ("e1000e: Separate signaling for link check/link
up") and its followups. After reverting, the race condition described in
the log of commit 19110cfbb34d is reintroduced. It may still be triggered
by LSC events but this should keep the link down in case the link is
electrically unstable, as discussed. The race may no longer be
triggered by RXO events because commit 4aea7a5c5e94 ("e1000e: Avoid
receiver overrun interrupt bursts") restored reading icr in the Other
handler.
Chris Wilson [Thu, 8 Mar 2018 14:26:47 +0000 (14:26 +0000)]
drm/i915: Kick the rps worker when changing the boost frequency
The boost frequency is only applied from the RPS worker while someone is
waiting on a request and requested a boost. As such, when the user
wishes to change the frequency, we have to kick the worker in order to
re-evaluate whether to apply the boost frequency.
v2: Check num_waiters to decide if we should kick the worker to handle
boosting.
Chris Wilson [Wed, 7 Mar 2018 17:13:03 +0000 (17:13 +0000)]
drm/i915: Only prune fences after wait-for-all
Currently, we only allow ourselves to prune the fences so long as
all the waits completed (i.e. all the fences we checked were signaled),
and that the reservation snapshot did not change across the wait.
However, if we only waited for a subset of the reservation object, i.e.
just waiting for the last writer to complete as opposed to all readers
as well, then we would erroneously conclude we could prune the fences as
indeed although all of our waits were successful, they did not represent
the totality of the reservation object.
v2: We only need to check the shared fences due to construction (i.e.
all of the shared fences will be later than the exclusive fence, if
any).
Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.
This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.
v2:
- Remove unnecessary information in commit message.
- Assign vbt.backlight.controller to a backlight_controller variable and
return the variable value.
v3:
- Rebased to latest code base.
- updated commit title.
Jerome Brunet [Wed, 14 Feb 2018 13:43:36 +0000 (14:43 +0100)]
clk: migrate the count of orphaned clocks at init
The orphan clocks reparents should migrate any existing count from the
orphan clock to its new acestor clocks, otherwise we may have
inconsistent counts in the tree and end-up with gated critical clocks
Assuming we have two clocks, A and B.
* Clock A has CLK_IS_CRITICAL flag set.
* Clock B is an ancestor of A which can gate. Clock B gate is left
enabled by the bootloader.
Step 1: Clock A is registered. Since it is a critical clock, it is
enabled. The clock being still an orphan, no parent are enabled.
Step 2: Clock B is registered and reparented to clock A (potentially
through several other clocks). We are now in situation where the enable
count of clock A is 1 while the enable count of its ancestors is 0, which
is not good.
Step 3: in lateinit, clk_disable_unused() is called, the enable_count of
clock B being 0, clock B is gated and and critical clock A actually gets
disabled.
This situation was found while adding fdiv_clk gates to the meson8b
platform. These clocks parent clk81 critical clock, which is the mother
of all peripheral clocks in this system. Because of the issue described
here, the system is crashing when clk_disable_unused() is called.
The situation is solved by reverting
commit f8f8f1d04494 ("clk: Don't touch hardware when reparenting during registration").
To avoid breaking again the situation described in this commit
description, enabling critical clock should be done before walking the
orphan list. This way, a parent critical clock may not be accidentally
disabled due to the CLK_OPS_PARENT_ENABLE mechanism.
Linus Torvalds [Mon, 12 Mar 2018 17:47:03 +0000 (10:47 -0700)]
Merge tag 'nfs-for-4.16-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Hightlights include the following stable fixes:
- NFS: Fix an incorrect type in struct nfs_direct_req
- pNFS: Prevent the layout header refcount going to zero in
pnfs_roc()
- NFS: Fix unstable write completion"
* tag 'nfs-for-4.16-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix unstable write completion
pNFS: Prevent the layout header refcount going to zero in pnfs_roc()
NFS: Fix an incorrect type in struct nfs_direct_req
The following patchset contains Netfilter fixes for your net tree, they are:
1) Fixed hashtable representation doesn't support timeout flag, skip it
otherwise rules to add elements from the packet fail bogusly fail with
EOPNOTSUPP.
2) Fix bogus error with 32-bits ebtables userspace and 64-bits kernel,
patch from Florian Westphal.
3) Sanitize proc names in several x_tables extensions, also from Florian.
4) Add sanitization to ebt_among wormhash logic, from Florian.
5) Missing release of hook array in flowtable.
====================
Takashi Iwai [Mon, 12 Mar 2018 16:30:38 +0000 (17:30 +0100)]
Merge tag 'asoc-fix-v4.16-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.16
This is a fairly standard collection of fixes, there's no changes to the
core here just a bunch of small device specific changes for single
drivers plus an update to the MAINTAINERS file for the sgl5000.
David S. Miller [Mon, 12 Mar 2018 15:16:40 +0000 (11:16 -0400)]
Merge tag 'linux-can-fixes-for-4.16-20180312' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-03-12
this is a pull reqeust of 6 patches for net/master.
The first patch is by Wolfram Sang and fixes a bitshift vs. comparison mistake
in the m_can driver. Two patches of Marek Vasut repair the error handling in
the ifi driver. The two patches by Stephane Grosjean fix a "echo_skb is
occupied!" bug in the peak/pcie_fd driver. Bich HEMON's patch adds pinctrl
select state calls to the m_can's driver to further improve power saving during
suspend.
====================
Masami Hiramatsu [Mon, 12 Mar 2018 10:00:49 +0000 (19:00 +0900)]
error-injection: Fix to prohibit jump optimization
Since the kprobe which was optimized by jump can not change
the execution path, the kprobe for error-injection must not
be optimized. To prohibit it, set a dummy post-handler as
officially stated in Documentation/kprobes.txt.
Fixes: 4b1a29a7f542 ("error-injection: Support fault injection framework") Signed-off-by: Masami Hiramatsu <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]>
Xin Long [Sat, 10 Mar 2018 10:57:50 +0000 (18:57 +0800)]
sock_diag: request _diag module only when the family or proto has been registered
Now when using 'ss' in iproute, kernel would try to load all _diag
modules, which also causes corresponding family and proto modules
to be loaded as well due to module dependencies.
Like after running 'ss', sctp, dccp, af_packet (if it works as a module)
would be loaded.
As these family and proto modules are loaded unintentionally, it
could cause some problems, like:
- Some debug tools use 'ss' to collect the socket info, which loads all
those diag and family and protocol modules. It's noisy for identifying
issues.
- Users usually expect to drop sctp init packet silently when they
have no sense of sctp protocol instead of sending abort back.
- It wastes resources (especially with multiple netns), and SCTP module
can't be unloaded once it's loaded.
...
In short, it's really inappropriate to have these family and proto
modules loaded unexpectedly when just doing debugging with inet_diag.
This patch is to introduce sock_load_diag_module() where it loads
the _diag module only when it's corresponding family or proto has
been already registered.
Note that we can't just load _diag module without the family or
proto loaded, as some symbols used in _diag module are from the
family or proto module.
v1->v2:
- move inet proto check to inet_diag to avoid a compiling err.
v2->v3:
- define sock_load_diag_module in sock.c and export one symbol
only.
- improve the changelog.
David S. Miller [Mon, 12 Mar 2018 14:58:28 +0000 (10:58 -0400)]
Merge branch 'bnxt_en-Bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
There are 3 bug fixes in this series to fix regressions recently
introduced when adding the new ring reservations scheme. 2 minor
fixes in the TC Flower code to return standard errno values and
to elide some unnecessary warning dmesg. One Fixes the VLAN TCI
value passed to the stack by including the entire 16-bit VLAN TCI,
and the last fix is to check for valid VNIC ID before setting up or
shutting down LRO/GRO.
====================
Michael Chan [Sat, 10 Mar 2018 04:46:10 +0000 (23:46 -0500)]
bnxt_en: Check valid VNIC ID in bnxt_hwrm_vnic_set_tpa().
During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID. This may cause a
warning in firmware logs.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Venkat Duvvuru [Sat, 10 Mar 2018 04:46:09 +0000 (23:46 -0500)]
bnxt_en: close & open NIC, only when the interface is in running state.
bnxt_restore_pf_fw_resources routine frees PF resources by calling
close_nic and allocates the resources back, by doing open_nic. However,
this is not needed, if the PF is already in closed state.
This bug causes the driver to call open the device and call request_irq()
when it is not needed. Ultimately, pci_disable_msix() will crash
when bnxt_en is unloaded.
This patch fixes the problem by skipping __bnxt_close_nic and
__bnxt_open_nic inside bnxt_restore_pf_fw_resources routine, if the
interface is not running.
Fixes: 80fcaf46c092 ("bnxt_en: Restore MSIX after disabling SRIOV.") Signed-off-by: Venkat Duvvuru <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Venkat Duvvuru [Sat, 10 Mar 2018 04:46:08 +0000 (23:46 -0500)]
bnxt_en: Return standard Linux error codes for hwrm flow cmds.
Currently, internal error value is returned by the driver, when
hwrm_cfa_flow_alloc() fails due lack of resources. We should be returning
Linux errno value -ENOSPC instead.
This patch also converts other similar command errors to standard Linux errno
code (-EIO) in bnxt_tc.c
Fixes: db1d36a27324 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds") Signed-off-by: Venkat Duvvuru <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Sat, 10 Mar 2018 04:46:07 +0000 (23:46 -0500)]
bnxt_en: Fix regressions when setting up MQPRIO TX rings.
Recent changes added the bnxt_init_int_mode() call in the driver's open
path whenever ring reservations are changed. This call was previously
only called in the probe path. In the open path, if MQPRIO TC has been
setup, the bnxt_init_int_mode() call would reset and mess up the MQPRIO
per TC rings.
Fix it by not re-initilizing bp->tx_nr_rings_per_tc in
bnxt_init_int_mode(). Instead, initialize it in the probe path only
after the bnxt_init_int_mode() call.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Sat, 10 Mar 2018 04:46:06 +0000 (23:46 -0500)]
bnxt_en: Pass complete VLAN TCI to the stack.
When receiving a packet with VLAN tag, pass the entire 16-bit TCI to the
stack when calling __vlan_hwaccel_put_tag(). The current code is only
passing the 12-bit tag and it is missing the priority bits.
bnxt_en: Remove unwanted ovs-offload messages in some conditions
In some conditions when the driver fails to add a flow in HW and returns
an error back to the stack, the stack continues to invoke get_flow_stats()
and/or del_flow() on it. The driver fails these APIs with an error message
"no flow_node for cookie". The message gets logged repeatedly as long as
the stack keeps invoking these functions.
Fix this by removing the corresponding netdev_info() calls from these
functions.
Fixes: d7bc73053024 ("bnxt_en: add code to query TC flower offload stats") Signed-off-by: Sriharsha Basavapatna <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Eddie Wai [Sat, 10 Mar 2018 04:46:04 +0000 (23:46 -0500)]
bnxt_en: Fix vnic accounting in the bnxt_check_rings() path.
The number of vnics to check must be determined ahead of time because
only standard RX rings require vnics to support RFS. The logic is
similar to the ring reservation logic and we can now use the
refactored common functions to do most of the work in setting up
the firmware message.
Fixes: 8f23d638b36b ("bnxt_en: Expand bnxt_check_rings() to check all resources.") Signed-off-by: Eddie Wai <[email protected]> Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Michael Chan [Sat, 10 Mar 2018 04:46:03 +0000 (23:46 -0500)]
bnxt_en: Refactor the functions to reserve hardware rings.
The bnxt_hwrm_reserve_{pf|vf}_rings() functions are very similar to
the bnxt_hwrm_check_{pf|vf}_rings() functions. Refactor the former
so that the latter can make use of common code in the next patch.
Brad Mouring [Thu, 8 Mar 2018 22:23:03 +0000 (16:23 -0600)]
net: phy: Tell caller result of phy_change()
In 664fcf123a30e (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.
With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Takashi Iwai [Mon, 12 Mar 2018 12:55:48 +0000 (13:55 +0100)]
ALSA: hda - Revert power_save option default value
With the commit 1ba8f9d30817 ("ALSA: hda: Add a power_save
blacklist"), we changed the default value of power_save option to -1
for processing the power-save blacklist.
Unfortunately, this seems breaking user-space applications that
actually read the power_save parameter value via sysfs and judge /
adjust the power-saving status. They see the value -1 as if the
power-save is turned off, although the actual value is taken from
CONFIG_SND_HDA_POWER_SAVE_DEFAULT and it can be a positive.
So, overall, passing -1 there was no good idea. Let's partially
revert it -- at least for power_save option default value is restored
again to CONFIG_SND_HDA_POWER_SAVE_DEFAULT. Meanwhile, in this patch,
we keep the blacklist behavior and make is adjustable via the new
option, pm_blacklist.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199073 Fixes: 1ba8f9d30817 ("ALSA: hda: Add a power_save blacklist") Acked-by: Hans de Goede <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
drm/sun4i: Fix an error handling path in 'sun4i_drv_bind()'
Commit 070badfab767 ("drm/sun4i: call drm_vblank_init with correct number
of crtcs") has moved some code without updating the error handling gotos
accordingly.
Branch to the correct label and remove a now unused lablel.
Arnd Bergmann [Wed, 10 Jan 2018 16:35:43 +0000 (17:35 +0100)]
phy: qcom-ufs: add MODULE_LICENSE tag
While the specific UFS PHY drivers (14nm and 20nm) have a module
license, the common base module does not, leading to a Kbuild
failure:
WARNING: modpost: missing MODULE_LICENSE() in drivers/phy/qualcomm/phy-qcom-ufs.o
FATAL: modpost: GPL-incompatible module phy-qcom-ufs.ko uses GPL-only symbol 'clk_enable'
This adds a module description and license tag to fix the build.
I added both Yaniv and Vivek as authors here, as Yaniv sent the initial
submission, while Vivek did most of the work since.
Ondrej Jirman [Sat, 10 Mar 2018 11:05:11 +0000 (12:05 +0100)]
drm/sun4i: Fix exclusivity of the TCON clocks
Currently the exclusivity is enabled when the rate is set by
the mode setting functions. These functions are called by
mode_set_nofb callback of drm_crc_helper. Then exclusivity
is disabled when tcon is disabled by atomic_disable
callback.
What happens is that mode_set_nofb can be called once when
mode changes, and afterwards the system can call atomic_enable
and atomic_disable multiple times without further calls to
mode_set_nofb.
This happens:
mode_set_nofb - clk exclusivity is enabled
atomic_enable
atomic_disable - clk exclusivity is disabled
atomic_enable
atomic_disable - clk exclusivity is already disabled, leading to WARN
in clk_rate_exclusive_put
Solution is to enable exclusivity in sun4i_tcon_channel_set_status.
can: peak/pcie_fd: remove useless code when interface starts
When an interface starts, the echo_skb array is empty and the network
queue should be started only. This patch replaces useless code and locks
when the internal RX_BARRIER message is received from the IP core, telling
the driver that tx may start.
This patch makes atomic the handling of the linux-can echo_skb array and
the network tx queue. This prevents from the "BUG! echo_skb is occupied!"
message to be printed by the linux-can core, in SMP environments.
Marek Vasut [Thu, 1 Mar 2018 18:34:00 +0000 (19:34 +0100)]
can: ifi: Repair the error handling
The new version of the IFI CANFD core has significantly less complex
error state indication logic. In particular, the warning/error state
bits are no longer all over the place, but are all present in the
STATUS register. Moreover, there is a new IRQ register bit indicating
transition between error states (active/warning/passive/busoff).
This patch makes use of this bit to weed out the obscure selective
INTERRUPT register clearing, which was used to carry over the error
state indication into the poll function. While at it, this patch
fixes the handling of the ACTIVE state, since the hardware provides
indication of the core being in ACTIVE state and that in turn fixes
the state transition indication toward userspace. Finally, register
reads in the poll function are moved to the matching subfunctions
since those are also no longer needed in the poll function.
Marek Vasut [Mon, 5 Mar 2018 20:29:52 +0000 (21:29 +0100)]
can: ifi: Check core revision upon probe
Older versions of the core are not compatible with the driver due
to various intrusive fixes of the core. Read out the VER register,
check the core revision bitfield and verify if the core in use is
new enough (rev 2.1 or newer) to work correctly with this driver.
Shannon Nelson [Fri, 9 Mar 2018 00:17:23 +0000 (16:17 -0800)]
macvlan: filter out unsupported feature flags
Adding a macvlan device on top of a lowerdev that supports
the xfrm offloads fails with a new regression:
# ip link add link ens1f0 mv0 type macvlan
RTNETLINK answers: Operation not permitted
Tracing down the failure shows that the macvlan device inherits
the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags
from the lowerdev, but with no dev->xfrmdev_ops API filled
in, it doesn't actually support xfrm. When the request is
made to add the new macvlan device, the XFRM listener for
NETDEV_REGISTER calls xfrm_api_check() which fails the new
registration because dev->xfrmdev_ops is NULL.
The macvlan creation succeeds when we filter out the ESP
feature flags in macvlan_fix_features(), so let's filter them
out like we're already filtering out ~NETIF_F_NETNS_LOCAL.
When XFRM support is added in the future, we can add the flags
into MACVLAN_FEATURES.
This same problem could crop up in the future with any other
new feature flags, so let's filter out any flags that aren't
defined as supported in macvlan.
Fixes: d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API") Reported-by: Alexey Kodanev <[email protected]> Signed-off-by: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Linus Torvalds [Sun, 11 Mar 2018 21:59:23 +0000 (14:59 -0700)]
Merge branch 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/pti updates from Thomas Gleixner:
"Yet another pile of melted spectrum related updates:
- Drop native vsyscall support finally as it causes more trouble than
benefit.
- Make microcode loading more robust. There were a few issues
especially related to late loading which are now surfacing because
late loading of the IB* microcodes addressing spectre issues has
become more widely used.
- Simplify and robustify the syscall handling in the entry code
- Prevent kprobes on the entry trampoline code which lead to kernel
crashes when the probe hits before CR3 is updated
- Don't check microcode versions when running on hypervisors as they
are considered as lying anyway.
- Fix the 32bit objtool build and a coment typo"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Fix kernel crash when probing .entry_trampoline code
x86/pti: Fix a comment typo
x86/microcode: Synchronize late microcode loading
x86/microcode: Request microcode on the BSP
x86/microcode/intel: Look into the patch cache first
x86/microcode: Do not upload microcode if CPUs are offline
x86/microcode/intel: Writeback and invalidate caches before updating microcode
x86/microcode/intel: Check microcode revision before updating sibling threads
x86/microcode: Get rid of struct apply_microcode_ctx
x86/spectre_v2: Don't check microcode versions when running under hypervisors
x86/vsyscall/64: Drop "native" vsyscalls
x86/entry/64/compat: Save one instruction in entry_INT80_compat()
x86/entry: Do not special-case clone(2) in compat entry
x86/syscalls: Use COMPAT_SYSCALL_DEFINEx() macros for x86-only compat syscalls
x86/syscalls: Use proper syscall definition for sys_ioperm()
x86/entry: Remove stale syscall prototype
x86/syscalls/32: Simplify $entry == $compat entries
objtool: Fix 32-bit build
Linus Torvalds [Sun, 11 Mar 2018 21:55:15 +0000 (14:55 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"Just a single fix which adds a missing Kconfig dependency to avoid
unmet dependency warnings"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/atmel-st: Add 'depends on HAS_IOMEM' to fix unmet dependency
Linus Torvalds [Sun, 11 Mar 2018 21:52:41 +0000 (14:52 -0700)]
Merge branch 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS fixes from Thomas Gleixner:
"Two small fixes for RAS/MCE:
- Serialize sysfs changes to avoid concurrent modificaiton of
underlying data
- Add microcode revision to Machine Check records. This should have
been there forever, but now with the broken microcode versions in
the wild it has become important"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE: Serialize sysfs changes
x86/MCE: Save microcode revision in machine check records
Linus Torvalds [Sun, 11 Mar 2018 21:49:49 +0000 (14:49 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Thomas Gleixner:
"Another set of perf updates:
- Fix a Skylake Uncore event format declaration
- Prevent perf pipe mode from crahsing which was caused by a missing
buffer allocation
- Make the perf top popup message which tells the user that it uses
fallback mode on older kernels a debug message.
- Make perf context rescheduling work correcctly
- Robustify the jump error drawing in perf browser mode so it does
not try to create references to NULL initialized offset entries
- Make trigger_on() robust so it does not enable the trigger before
everything is set up correctly to handle it
- Make perf auxtrace respect the --no-itrace option so it does not
try to queue AUX data for decoding.
- Prevent having different number of field separators in CVS output
lines when a counter is not supported.
- Make the perf kallsyms man page usage behave like it does for all
other perf commands.
- Synchronize the kernel headers"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix ctx_event_type in ctx_resched()
perf tools: Fix trigger class trigger_on()
perf auxtrace: Prevent decoding when --no-itrace
perf stat: Fix CVS output format for non-supported counters
tools headers: Sync x86's cpufeatures.h
tools headers: Sync copy of kvm UAPI headers
perf record: Fix crash in pipe mode
perf annotate browser: Be more robust when drawing jump arrows
perf top: Fix annoying fallback message on older kernels
perf kallsyms: Fix the usage on the man page
perf/x86/intel/uncore: Fix Skylake UPI event format
Linus Torvalds [Sun, 11 Mar 2018 21:46:54 +0000 (14:46 -0700)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"rt_mutex_futex_unlock() grew a new irq-off call site, but the function
assumes that its always called from irq enabled context.
Use (un)lock_irqsafe() to handle the new call site correctly"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Make rt_mutex_futex_unlock() safe for irq-off callsites
netfilter: bridge: ebt_among: add more missing match size checks
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
commit c4585a2823edf ("bridge: ebt_among: add missing match size checks")
added validation for pool size, but missed fact that the macros
ebt_among_wh_src/dst can already return out-of-bound result because
they do not check value of wh_src/dst_ofs (an offset) vs. the size
of the match that userspace gave to us.
v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst
wormhash arrays do not overlap, and src + length lines up with
start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part
NB: Fixes tag is intentionally wrong, this bug exists from day
one when match was added for 2.6 kernel. Tag is there so stable
maintainers will notice this one too.
netfilter: ebtables: fix erroneous reject of last rule
The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.
Linus Torvalds [Sun, 11 Mar 2018 20:07:14 +0000 (13:07 -0700)]
Merge tag 'dmaengine-fix-4.16-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Two small fixes are for this cycle:
- fix max_chunk_size for rcar-dmac for R-Car Gen3
- fix clock resource of mv_xor_v2"
* tag 'dmaengine-fix-4.16-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: mv_xor_v2: Fix clock resource by adding a register clock
dmaengine: rcar-dmac: fix max_chunk_size for R-Car Gen3
Gregory CLEMENT [Wed, 7 Mar 2018 15:40:10 +0000 (16:40 +0100)]
dmaengine: mv_xor_v2: Fix clock resource by adding a register clock
On the CP110 components which are present on the Armada 7K/8K SoC we need
to explicitly enable the clock for the registers. However it is not
needed for the AP8xx component, that's why this clock is optional.
With this patch both clock have now a name, but in order to be backward
compatible, the name of the first clock is not used. It allows to still
use this clock with a device tree using the old binding.
Ard Biesheuvel [Tue, 6 Mar 2018 15:51:32 +0000 (15:51 +0000)]
irqchip/gic-v3-its: Ensure nr_ites >= nr_lpis
When struct its_device instances are created, the nr_ites member
will be set to a power of 2 that equals or exceeds the requested
number of MSIs passed to the msi_prepare() callback. At the same
time, the LPI map is allocated to be some multiple of 32 in size,
where the allocated size may be less than the requested size
depending on whether a contiguous range of sufficient size is
available in the global LPI bitmap.
This may result in the situation where the nr_ites < nr_lpis, and
since nr_ites is what we program into the hardware when we map the
device, the additional LPIs will be non-functional.
For bog standard hardware, this does not really matter. However,
in cases where ITS device IDs are shared between different PCIe
devices, we may end up allocating these additional LPIs without
taking into account that they don't actually work.
So let's make nr_ites at least 32. This ensures that all allocated
LPIs are 'live', and that its_alloc_device_irq() will fail when
attempts are made to allocate MSIs beyond what was allocated in
the first place.
Takashi Iwai [Sat, 10 Mar 2018 22:04:23 +0000 (23:04 +0100)]
ALSA: pcm: Fix UAF in snd_pcm_oss_get_formats()
snd_pcm_oss_get_formats() has an obvious use-after-free around
snd_mask_test() calls, as spotted by syzbot. The passed format_mask
argument is a pointer to the hw_params object that is freed before the
loop. What a surprise that it has been present since the original
code of decades ago...
Linus Torvalds [Sat, 10 Mar 2018 18:21:07 +0000 (10:21 -0800)]
Merge tag 'kbuild-fixes-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- make fixdep parse kconfig.h to fix missing rebuild
- replace hyphens with underscores in builtin DTB label names
- fix typos
* tag 'kbuild-fixes-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: Handle builtin dtb file names containing hyphens
scripts/bloat-o-meter: fix typos in help
fixdep: do not ignore kconfig.h
fixdep: remove some false CONFIG_ matches
fixdep: remove stale references to uml-config.h
Linus Torvalds [Sat, 10 Mar 2018 18:17:59 +0000 (10:17 -0800)]
Merge tag 'linux-watchdog-4.16-fixes-2' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- f71808e_wdt: Fix magic close handling
- sbsa: 32-bit read fix for WCV
- hpwdt: Remove legacy NMI sourcing
* tag 'linux-watchdog-4.16-fixes-2' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: hpwdt: Remove legacy NMI sourcing.
watchdog: sbsa: use 32-bit read for WCV
watchdog: f71808e_wdt: Fix magic close handling
Linus Torvalds [Sat, 10 Mar 2018 16:48:01 +0000 (08:48 -0800)]
Merge tag 'for-linus-20180309' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- a xen-blkfront fix from Bhavesh with a multiqueue fix when
detaching/re-attaching
- a few important NVMe fixes, including a revert for a sysfs fix that
caused some user space confusion
- two bcache fixes by way of Michael Lyle
- a loop regression fix, fixing an issue with lost writes on DAX.
* tag 'for-linus-20180309' of git://git.kernel.dk/linux-block:
loop: Fix lost writes caused by missing flag
nvme_fc: rework sqsize handling
nvme-fabrics: Ignore nr_io_queues option for discovery controllers
xen-blkfront: move negotiate_mq to cover all cases of new VBDs
Revert "nvme: create 'slaves' and 'holders' entries for hidden controllers"
bcache: don't attach backing with duplicate UUID
bcache: fix crashes in duplicate cache device register
nvme: pci: pass max vectors as num_possible_cpus() to pci_alloc_irq_vectors
nvme-pci: Fix EEH failure on ppc
Linus Torvalds [Sat, 10 Mar 2018 16:45:44 +0000 (08:45 -0800)]
Merge tag 'for-4.16/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix an uninitialized variable false warning in dm bufio
- Fix DM's passthrough ioctl support to be race free against an
underlying device being removed.
- Fix corner-case of DM raid resync reporting if/when the raid becomes
degraded during resync; otherwise automated raid repair will fail.
- A few DM multipath fixes to make non-SCSI optimizations, that were
introduced during the 4.16 merge, useful for all non-SCSI devices,
rather than narrowly define this non-SCSI mode in terms of "nvme".
This allows the removal of "queue_mode nvme" that really didn't need
to be introduced. Instead DM core will internalize whether
nvme-specific IO submission optimizations are doable and DM multipath
will only do SCSI-specific device handler operations if SCSI is in
use.
* tag 'for-4.16/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: allow upgrade from bio-based to specialized bio-based variant
dm mpath: remove unnecessary NVMe branching in favor of scsi_dh checks
dm table: fix "nvme" test
dm raid: fix incorrect sync_ratio when degraded
dm: use blkdev_get rather than bdgrab when issuing pass-through ioctl
dm bufio: avoid false-positive Wmaybe-uninitialized warning
Linus Torvalds [Sat, 10 Mar 2018 16:38:01 +0000 (08:38 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
- Various driver bug fixes in mlx5, mlx4, bnxt_re and qedr, ranging
from bugs under load to bad error case handling
- There in one largish patch fixing the locking in bnxt_re to avoid a
machine hard lock situation
- A few core bugs on error paths
- A patch to reduce stack usage in the new CQ API
- One mlx5 regression introduced in this merge window
- There were new syzkaller scripts written for the RDMA subsystem and
we are fixing issues found by the bot
- One of the commits (aa0de36a40f4 “RDMA/mlx5: Fix integer overflow
while resizing CQ”) is missing part of the commit log message and one
of the SOB lines. The original patch was from Leon Romanovsky, and a
cut-n-paste separator in the commit message confused patchworks which
then put the end of message separator in the wrong place in the
downloaded patch, and I didn’t notice in time. The patch made it into
the official branch, and the only way to fix it in-place was to
rebase. Given the pain that a rebase causes, and the fact that the
patch has relevant tags for stable and syzkaller, a revert of the
munged patch and a reapplication of the original patch with the log
message intact was done.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (25 commits)
RDMA/mlx5: Fix integer overflow while resizing CQ
Revert "RDMA/mlx5: Fix integer overflow while resizing CQ"
RDMA/ucma: Check that user doesn't overflow QP state
RDMA/mlx5: Fix integer overflow while resizing CQ
RDMA/ucma: Limit possible option size
IB/core: Fix possible crash to access NULL netdev
RDMA/bnxt_re: Avoid Hard lockup during error CQE processing
RDMA/core: Reduce poll batch for direct cq polling
IB/mlx5: Fix an error code in __mlx5_ib_modify_qp()
IB/mlx5: When not in dual port RoCE mode, use provided port as native
IB/mlx4: Include GID type when deleting GIDs from HW table under RoCE
IB/mlx4: Fix corruption of RoCEv2 IPv4 GIDs
RDMA/qedr: Fix iWARP write and send with immediate
RDMA/qedr: Fix kernel panic when running fio over NFSoRDMA
RDMA/qedr: Fix iWARP connect with port mapper
RDMA/qedr: Fix ipv6 destination address resolution
IB/core : Add null pointer check in addr_resolve
RDMA/bnxt_re: Fix the ib_reg failure cleanup
RDMA/bnxt_re: Fix incorrect DB offset calculation
RDMA/bnxt_re: Unconditionly fence non wire memory operations
...
Linus Torvalds [Sat, 10 Mar 2018 16:35:29 +0000 (08:35 -0800)]
Merge tag 'platform-drivers-x86-v4.16-6' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Correct a module loading race condition between the DELL_SMBIOS
backend modules and the first user by converting them to bool features
of the DELL_SMBIOS driver. Fixup the resulting Kconfig dependency
issue with DCDBAS"
* tag 'platform-drivers-x86-v4.16-6' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-smbios: Resolve dependency error on DCDBAS
platform/x86: Allow for SMBIOS backend defaults
platform/x86: dell-smbios: Link all dell-smbios-* modules together
platform/x86: dell-smbios: Rename dell-smbios source to dell-smbios-base
platform/x86: dell-smbios: Correct some style warnings
Takashi Iwai [Fri, 9 Mar 2018 21:23:31 +0000 (22:23 +0100)]
ALSA: seq: Clear client entry before deleting else at closing
When releasing a client, we need to clear the clienttab[] entry at
first, then call snd_seq_queue_client_leave(). Otherwise, the
in-flight cell in the queue might be picked up by the timer interrupt
via snd_seq_check_queue() before calling snd_seq_queue_client_leave(),
and it's delivered to another queue while the client is clearing
queues. This may eventually result in an uncleared cell remaining in
a queue, and the later snd_seq_pool_delete() may need to wait for a
long time until the event gets really processed.
By moving the clienttab[] clearance at the beginning of release, any
event delivery of a cell belonging to this client will fail at a later
point, since snd_seq_client_ptr() returns NULL. Thus the cell that
was picked up by the timer interrupt will be returned immediately
without further delivery, and the long stall of snd_seq_delete_pool()
can be avoided, too.
Takashi Iwai [Fri, 9 Mar 2018 20:58:28 +0000 (21:58 +0100)]
ALSA: seq: Fix possible UAF in snd_seq_check_queue()
Although we've covered the races between concurrent write() and
ioctl() in the previous patch series, there is still a possible UAF in
the following scenario:
So the problem is that a cell is peeked and accessed without any
protection until it's retrieved from the queue again via
snd_seq_prioq_cell_out().
This patch tries to address it, also cleans up the code by a slight
refactoring. snd_seq_prioq_cell_out() now receives an extra pointer
argument. When it's non-NULL, the function checks the event timestamp
with the given pointer. The caller needs to pass the right reference
either to snd_seq_tick or snd_seq_realtime depending on the event
timestamp type.
A good news is that the above change allows us to remove the
snd_seq_prioq_cell_peek(), too, thus the patch actually reduces the
code size.
iio: st_pressure: st_accel: pass correct platform data to init
Commit 7383d44b added a pointer pdata which get set to the default
platform_data when non was defined in the device. But it did not
pass this pointer to the st_sensors_init_sensor call but still
used the maybe uninitialized platform_data from dev.
This breaks initialization when no platform_data is given and
the optional st,drdy-int-pin devicetree option is not set.
This commit fixes this.
Cc: [email protected] Fixes: 7383d44b ("iio: st_pressure: st_accel: Initialise sensor platform data properly") Signed-off-by: Michael Nosthoff <[email protected]> Signed-off-by: Jonathan Cameron <[email protected]>
projects / linux.git / log