Leon Romanovsky [Thu, 23 Sep 2021 18:12:49 +0000 (21:12 +0300)]
bnxt_en: Properly remove port parameter support
This driver doesn't have any port parameters and registers
devlink port parameters with empty table. Remove the useless
calls to devlink_port_params_register and _unregister.
Fixes: da203dfa89ce ("Revert "devlink: Add a generic wake_on_lan port parameter"") Signed-off-by: Leon Romanovsky <[email protected]> Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Leon Romanovsky [Thu, 23 Sep 2021 18:12:48 +0000 (21:12 +0300)]
bnxt_en: Check devlink allocation and registration status
devlink is a software interface that doesn't depend on any hardware
capabilities. The failure in SW means memory issues, wrong parameters,
programmer error e.t.c.
Like any other such interface in the kernel, the returned status of
devlink APIs should be checked and propagated further and not ignored.
Fixes: 4ab0c6a8ffd7 ("bnxt_en: add support to enable VF-representors") Signed-off-by: Leon Romanovsky <[email protected]> Reviewed-by: Edwin Peer <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Fri, 24 Sep 2021 09:26:52 +0000 (10:26 +0100)]
Merge branch 'mlxsw-next'
Ido Schimmel says:
====================
mlxsw: Add support for IP-in-IP with IPv6 underlay
Currently, mlxsw only supports IP-in-IP with IPv4 underlay. Traffic
routed through 'gre' netdevs is encapsulated with IPv4 and GRE headers.
Similarly, incoming IPv4 GRE packets are decapsulated and routed in the
overlay VRF (which can be the same as the underlay VRF).
This patchset adds support for IPv6 underlay using the 'ip6gre' netdev.
Due to architectural differences between Spectrum-1 and later ASICs,
this functionality is only supported on Spectrum-2 onwards (the software
data path is used for Spectrum-1).
Patchset overview:
Patches #1-#5 are preparations.
Patches #6-#9 add and extend required device registers.
Amit Cohen [Thu, 23 Sep 2021 12:37:00 +0000 (15:37 +0300)]
mlxsw: Add support for IP-in-IP with IPv6 underlay for Spectrum-2 and above
Currently, mlxsw driver supports IP-in-IP only with IPv4 underlay.
Add support for IPv6 underlay for Spectrum-2 and above.
Most of the configurations are same to IPv4, the main difference between
IPv4 and IPv6 is related to saving IP addresses.
IPv6 addresses are saved as part of KVD and the relevant registers hold
pointer to them.
Add API for that as part of ipip_ops, so then only Spectrum-2 and above
will save IPv6 addresses in this way.
Amit Cohen [Thu, 23 Sep 2021 12:36:59 +0000 (15:36 +0300)]
mlxsw: spectrum_router: Increase parsing depth for IPv6 decapsulation
The Spectrum ASIC has a configurable limit on how deep into the packet
it parses. By default, the limit is 96 bytes.
For IP-in-IP packets, with IPv6 outer and inner headers, the default
parsing depth is not enough and without increasing it such packets cannot
be properly decapsulated.
Use the existing API to set parsing depth, call it once for each
decapsulation entry when it is created/destroyed.
There is no need to protect the code with new mutex because 'router->lock'
is already taken in these code paths.
Amit Cohen [Thu, 23 Sep 2021 12:36:58 +0000 (15:36 +0300)]
mlxsw: Add IPV6_ADDRESS kvdl entry type
Add support for allocating and freeing KVD entries for IPv6 addresses.
These addresses are programmed by the RIPS register and referenced by
the RATR and RTDP registers for IPv6 underlay encapsulation and
decapsulation, respectively.
Amit Cohen [Thu, 23 Sep 2021 12:36:56 +0000 (15:36 +0300)]
mlxsw: Create separate ipip_ops_arr for different ASICs
Currently, there is support for IP-in-IP only with IPv4 underlay for all
supported Spectrum ASICs.
The next patches will add support for IPv6 underlay only for Spectrum-2
and above.
Add infrastructure for splitting IP-in-IP support between different
ASICs - create separate ipip_ops_arr and add ipips_init function to set the
right ops.
Amit Cohen [Thu, 23 Sep 2021 12:36:54 +0000 (15:36 +0300)]
mlxsw: reg: Add support for ratr_ipip6_entry_pack()
The RATR register is used to configure the Router Adjacency (next-hop)
Table.
For IP-in-IP entry, underlay destination IPv4 is saved as part of this
register and underlay destination IPv6 is saved by RIPS register and RATR
saves pointer to it.
Add function for setting IPv6 IP-in-IP configuration.
Amit Cohen [Thu, 23 Sep 2021 12:36:53 +0000 (15:36 +0300)]
mlxsw: reg: Add support for rtdp_ipip6_pack()
The RTDP register is used for configuring the tunnel decapsulation
properties of NVE and IP-in-IP.
Linux tunnels verify packets before decapsulation based on the packet's
source IP, which must match tunnel remote IP.
RTDP is used to configure decapsulation so that it filters out packets that
are not IPv6 or have the wrong source IP or wrong GRE key.
For IP-in-IP entry, source IPv4 is saved as part of this register and
source IPv6 is saved by RIPS register and RTDP saves pointer to it.
Create common function for configuring both IPv4 and IPv6 and add
dedicated functions for each protocol.
Amit Cohen [Thu, 23 Sep 2021 12:36:52 +0000 (15:36 +0300)]
mlxsw: reg: Add Router IP version Six Register
The RIPS register is used to store IPv6 addresses for use by the NVE and
IP-in-IP.
For IPv6 underlay support, RATR register needs to hold a pointer to the
remote IPv6 address for encapsulation and RTDP register needs to hold a
pointer to the local IPv6 address for decapsulation check.
Add the required register for saving IPv6 addresses.
Amit Cohen [Thu, 23 Sep 2021 12:36:51 +0000 (15:36 +0300)]
mlxsw: Take tunnel's type into account when searching underlay device
The function __mlxsw_sp_ipip_netdev_ul_dev_get() returns the underlay
device that corresponds to the overlay device that it gets.
Currently, this function assumes that the tunnel is IPv4 GRE, because it
is the only one that is supported by mlxsw driver.
This assumption will no longer be correct when IPv6 GRE support is added,
resulting in wrong underlay device being returned.
Instead, check 'ol_dev->type' and return the underlay device accordingly.
Move the function to spectrum_ipip.c because spectrum_router.c should not
be aware to tunnel type.
Amit Cohen [Thu, 23 Sep 2021 12:36:50 +0000 (15:36 +0300)]
mlxsw: spectrum_ipip: Create common function for mlxsw_sp_ipip_ol_netdev_change_gre()
The function mlxsw_sp_ipip_ol_netdev_change_gre4() contains code that
can be shared between IPv4 and IPv6.
The only difference is the way that arguments are taken from tunnel
parameters, which are different between IPv4 and IPv6.
For that, add structure 'mlxsw_sp_ipip_parms' to hold all the required
parameters for the function and save it as part of
'struct mlxsw_sp_ipip_entry' instead of the existing structure that is
not shared between IPv4 and IPv6. Add new operation as part of
'mlxsw_sp_ipip_ops' to initialize the new structure.
Then mlxsw_sp_ipip_ol_netdev_change_gre{4,6}() will prepare the new
structure and both will call the same function.
Amit Cohen [Thu, 23 Sep 2021 12:36:49 +0000 (15:36 +0300)]
mlxsw: spectrum_router: Fix arguments alignment
Suppress the following checkpatch.pl check [1] by adding a variable to
store the IP-in-IP options. Noticed while adding equivalent IPv6 code in
subsequent patches.
[1]
CHECK: Alignment should match open parenthesis
+ mlxsw_reg_ritr_loopback_ipip4_pack(ritr_pl, lb_cf.lb_ipipt,
+
+ MLXSW_REG_RITR_LOOPBACK_IPIP_OPTIONS_GRE_KEY_PRESET,
Amit Cohen [Thu, 23 Sep 2021 12:36:47 +0000 (15:36 +0300)]
mlxsw: spectrum_router: Create common function for fib_entry_type_unset() code
mlxsw_sp_fib4_entry_type_unset() is not specific for IPv4 FIB entry,
move the code to mlxsw_sp_fib_entry_type_unset(), and call this function
from mlxsw_sp_fib4_entry_type_unset() so then it will be used for IPv6
also.
Merge tag 'net-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Current release - regressions:
- dsa: bcm_sf2: fix array overrun in bcm_sf2_num_active_ports()
Previous releases - regressions:
- introduce a shutdown method to mdio device drivers, and make DSA
switch drivers compatible with masters disappearing on shutdown;
preventing infinite reference wait
- fix issues in mdiobus users related to ->shutdown vs ->remove
- virtio-net: fix pages leaking when building skb in big mode
- xen-netback: correct success/error reporting for the
SKB-with-fraglist
- dsa: tear down devlink port regions when tearing down the devlink
port on error
- nexthop: fix division by zero while replacing a resilient group
- hns3: check queue, vf, vlan ids range before using
Previous releases - always broken:
- napi: fix race against netpoll causing NAPI getting stuck
- mlx4_en: ensure link operstate is updated even if link comes up
before netdev registration
- bnxt_en: fix TX timeout when TX ring size is set to the smallest
- enetc: fix illegal access when reading affinity_hint; prevent oops
on sysfs access
- core: correct the sock::sk_lock.owned lockdep annotations"
* tag 'net-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
atlantic: Fix issue in the pm resume flow.
net/mlx4_en: Don't allow aRFS for encapsulated packets
net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
net: ethernet: mtk_eth_soc: avoid creating duplicate offload entries
nfc: st-nci: Add SPI ID matching DT compatible
MAINTAINERS: remove Guvenc Gulce as net/smc maintainer
nexthop: Fix memory leaks in nexthop notification chain listeners
mptcp: ensure tx skbs always have the MPTCP ext
qed: rdma - don't wait for resources under hw error recovery flow
s390/qeth: fix deadlock during failing recovery
s390/qeth: Fix deadlock in remove_discipline
s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
net: dsa: realtek: register the MDIO bus under devres
net: dsa: don't allocate the slave_mii_bus using devres
Doc: networking: Fox a typo in ice.rst
net: dsa: fix dsa_tree_setup error path
net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
net/smc: add missing error check in smc_clc_prfx_set()
net: hns3: fix a return value error in hclge_get_reset_status()
net: hns3: check vlan id before using it
...
Prior to the commit 7e1c0d6f5820 ("memcg: switch lruvec stats to rstat")
and the commit aa48e47e3906 ("memcg: infrastructure to flush memcg
stats"), each lruvec memcg stats can be off by (nr_cgroups * nr_cpus *
32) at worst and for unbounded amount of time. The commit aa48e47e3906
moved the lruvec stats to rstat infrastructure and the commit 7e1c0d6f5820 bounded the error for all the lruvec stats to (nr_cpus *
32) at worst for at most 2 seconds. More specifically it decoupled the
number of stats and the number of cgroups from the error rate.
However this reduction in error comes with the cost of triggering the
slowpath of stats update more frequently. Previously in the slowpath
the kernel adds the stats up the memcg tree. After aa48e47e3906, the
kernel triggers the asyn lruvec stats flush through queue_work(). This
causes regression reports from 0day kernel bot [1] as well as from
phoronix test suite [2].
We tried two options to fix the regression:
1) Increase the threshold to trigger the slowpath in lruvec stats
update codepath from 32 to 512.
2) Remove the slowpath from lruvec stats update codepath and instead
flush the stats in the page refault codepath. The assumption is that
the kernel timely flush the stats, so, the update tree would be
small in the refault codepath to not cause the preformance impact.
Following are the results of will-it-scale/page_fault[1|2|3] benchmark
on four settings i.e. (1) 5.15-rc1 as baseline (2) 5.15-rc1 with aa48e47e3906 and 7e1c0d6f5820 reverted (3) 5.15-rc1 with option-1
(4) 5.15-rc1 with option-2.
From the above result, it seems like the option-2 not only solves the
regression but also improves the performance for at least these
benchmarks.
Feng Tang (intel) ran the aim7 benchmark with these two options and
confirms that option-1 reduces the regression but option-2 removes the
regression.
Michael Larabel (phoronix) ran multiple benchmarks with these options
and reported the results at [3] and it shows for most benchmarks
option-2 removes the regression introduced by the commit aa48e47e3906
("memcg: infrastructure to flush memcg stats").
Based on the experiment results, this patch proposed the option-2 as the
solution to resolve the regression.
After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.
Fixes: 57f780f1c433 ("atlantic: Fix driver resume flow.") Signed-off-by: Sudarsana Reddy Kalluru <[email protected]> Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vladimir Oltean [Thu, 23 Sep 2021 02:03:38 +0000 (19:03 -0700)]
net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
The blamed commit made the fatally incorrect assumption that ports which
aren't in the FORWARDING STP state should not have packets forwarded
towards them, and that is all that needs to be done.
However, that logic alone permits BLOCKING ports to forward to
FORWARDING ports, which of course allows packet storms to occur when
there is an L2 loop.
The ocelot_get_bridge_fwd_mask should not only ask "what can the bridge
do for you", but "what can you do for the bridge". This way, only
FORWARDING ports forward to the other FORWARDING ports from the same
bridging domain, and we are still compatible with the idea of multiple
bridges.
Sometimes multiple CLS_REPLACE calls are issued for the same connection.
rhashtable_insert_fast does not check for these duplicates, so multiple
hardware flow entries can be created.
Fix this by checking for an existing entry early
Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support") Signed-off-by: Felix Fietkau <[email protected]> Signed-off-by: Ilya Lipnitskiy <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vladimir Oltean [Wed, 22 Sep 2021 18:36:55 +0000 (21:36 +0300)]
net: dsa: sja1105: stop using priv->vlan_aware
Now that the sja1105 driver is finally sane enough again to stop having
a ternary VLAN awareness state, we can remove priv->vlan_aware and query
DSA for the ds->vlan_filtering value (for SJA1105, VLAN filtering is a
global property).
Also drop the paranoid checking that DSA calls ->port_vlan_filtering
multiple times without the VLAN awareness state changing. It doesn't,
the same check is present inside dsa_port_vlan_filtering too.
Mark Brown [Wed, 22 Sep 2021 18:30:37 +0000 (19:30 +0100)]
nfc: st-nci: Add SPI ID matching DT compatible
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding the part name used in
the compatible to the list of SPI IDs.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Thu, 23 Sep 2021 11:50:26 +0000 (12:50 +0100)]
Merge branch 'remove-sk-skb-caches'
Paolo Abeni says:
====================
net: remove sk skb caches
Eric noted we would be better off reverting the sk
skb caches.
MPTCP relies on such a feature, so we need a
little refactor of the MPTCP tx path before the mentioned
revert.
The first patch exposes additional TCP helpers. The 2nd patch
changes the MPTCP code to do locally the whole skb allocation
and updating, so it does not rely anymore on core TCP helpers
for that nor the sk skb cache.
As a side effect, we can make the tcp_build_frag helper static.
Finally, we can pull Eric's revert.
RFC -> v1:
- drop driver specific patch - no more needed after helper rename
- rename skb_entail -> tcp_skb_entail (Eric)
- preserve the tcp_build_frag helpwe, just make it static (Eric)
====================
Eric Dumazet [Wed, 22 Sep 2021 17:26:43 +0000 (19:26 +0200)]
tcp: remove sk_{tr}x_skb_cache
This reverts the following patches :
- commit 2e05fcae83c4 ("tcp: fix compile error if !CONFIG_SYSCTL")
- commit 4f661542a402 ("tcp: fix zerocopy and notsent_lowat issues")
- commit 472c2e07eef0 ("tcp: add one skb cache for tx")
- commit 8b27dae5a2e8 ("tcp: add one skb cache for rx")
Having a cache of one skb (in each direction) per TCP socket is fragile,
since it can cause a significant increase of memory needs,
and not good enough for high speed flows anyway where more than one skb
is needed.
We want instead to add a generic infrastructure, with more flexible
per-cpu caches, for alien NUMA nodes.
Paolo Abeni [Wed, 22 Sep 2021 17:26:41 +0000 (19:26 +0200)]
mptcp: stop relying on tcp_tx_skb_cache
We want to revert the skb TX cache, but MPTCP is currently
using it unconditionally.
Rework the MPTCP tx code, so that tcp_tx_skb_cache is not
needed anymore: do the whole coalescing check, skb allocation
skb initialization/update inside mptcp_sendmsg_frag(), quite
alike the current TCP code.
Paolo Abeni [Wed, 22 Sep 2021 11:12:17 +0000 (13:12 +0200)]
mptcp: ensure tx skbs always have the MPTCP ext
Due to signed/unsigned comparison, the expression:
info->size_goal - skb->len > 0
evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.
Due to the above, syzbot is able to trigger the following WARN_ON():
Vladimir Oltean [Wed, 22 Sep 2021 15:10:29 +0000 (18:10 +0300)]
net: dsa: sja1105: don't keep a persistent reference to the reset GPIO
The driver only needs the reset GPIO for a very brief period, so instead
of using devres and keeping the descriptor pointer inside priv, just use
that descriptor inside the sja1105_hw_reset function and then let go of
it.
Also use gpiod_get_optional while at it, and error out on real errors
(bad flags etc).
David S. Miller [Thu, 23 Sep 2021 11:45:07 +0000 (12:45 +0100)]
Merge branch 'ja1105-deps'
Vladimir Oltean says:
====================
Fix circular dependency between sja1105 and tag_sja1105
As discussed here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocols cannot use symbols exported by switch drivers.
Eliminate the two instances of that from tag_sja1105, and that allows us
to have a working setup with modules again.
====================
Vladimir Oltean [Wed, 22 Sep 2021 14:37:26 +0000 (17:37 +0300)]
net: dsa: sja1105: break dependency between dsa_port_is_sja1105 and switch driver
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Vladimir Oltean [Wed, 22 Sep 2021 14:37:25 +0000 (17:37 +0300)]
net: dsa: move sja1110_process_meta_tstamp inside the tagging protocol driver
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Vladimir Oltean [Wed, 22 Sep 2021 13:57:03 +0000 (16:57 +0300)]
net: dsa: sja1105: remove sp->dp
It looks like this field was never used since its introduction in commit 227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through
standalone ports") remove it.
nexthop: Fix memory leaks in nexthop notification chain listeners
syzkaller discovered memory leaks [1] that can be reduced to the
following commands:
# ip nexthop add id 1 blackhole
# devlink dev reload pci/0000:06:00.0
As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.
One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.
Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.
The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.
Fixes: 2a014b200bbd ("mlxsw: spectrum_router: Add support for nexthop objects") Signed-off-by: Ido Schimmel <[email protected]> Reviewed-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Juergen, Roger, and Stefano.
Merge tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi modalias fix from Mark Brown:
"Fix modalias issues
As reported by Russell King the change to use OF style modaliases for
DT enumerated broke at least the spi-nor driver, the patch here
reverts that change to fix the regression.
Sadly this will mean that anything that started loading since the
change to OF modaliases will run into issues, there doesn't seem to be
any approach which doesn't cause some problems and thi seems like the
least bad approach - gory details are in the commit log for the
change.
I'm currently working through the SPI drivers to add ID tables and
missing IDs to tables which should address things from the other end,
this seems more straightforward and robust than any other options"
* tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Revert modalias changes
Merge tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Critical bug fixes:
- Fix crash in NLM TEST procedure
- NFSv4.1+ backchannel not restored after PATH_DOWN"
* tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: back channel stuck in SEQ4_STATUS_CB_PATH_DOWN
NLM: Fix svcxdr_encode_owner()
Merge tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"The first round of bug-fixes for platform-drivers-x86 for 5.15,
highlights:
- amd-pmc fix for some suspend/resume issues
- intel-hid fix to avoid false-positive SW_TABLET_MODE=1 reporting
- some build error/warning fixes
- various DMI quirk additions"
* tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
platform/x86/intel: hid: Add DMI switches allow list
platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
platform/x86: amd-pmc: Increase the response register timeout
platform/x86: touchscreen_dmi: Update info for the Chuwi Hi10 Plus (CWI527) tablet
platform/x86: touchscreen_dmi: Add info for the Chuwi HiBook (CWI514) tablet
lg-laptop: Correctly handle dmi_get_system_info() returning NULL
platform/x86/intel: punit_ipc: Drop wrong use of ACPI_PTR()
Paolo Abeni [Wed, 22 Sep 2021 11:12:17 +0000 (13:12 +0200)]
mptcp: ensure tx skbs always have the MPTCP ext
Due to signed/unsigned comparison, the expression:
info->size_goal - skb->len > 0
evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.
Due to the above, syzbot is able to trigger the following WARN_ON():
qed: rdma - don't wait for resources under hw error recovery flow
If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.
Fixes: 64515dc899df ("qed: Add infrastructure for error detection and recovery") Signed-off-by: Michal Kalderon <[email protected]> Signed-off-by: Ariel Elior <[email protected]> Signed-off-by: Shai Malin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Wed, 22 Sep 2021 13:35:02 +0000 (14:35 +0100)]
Merge branch 'mlxsw-trap-adjacency'
Ido Schimmel says:
====================
mlxsw: Alter trap adjacency entry allocation scheme
In commit 0c3cbbf96def ("mlxsw: Add specific trap for packets routed via
invalid nexthops"), mlxsw started allocating a new adjacency entry
during driver initialization, to trap packets routed via invalid
nexthops.
This behavior was later altered in commit 983db6198f0d ("mlxsw:
spectrum_router: Allocate discard adjacency entry when needed") to only
allocate the entry upon the first route that requires it. The motivation
for the change is explained in the commit message.
The problem with the current behavior is that the entry shows up as a
"leak" in a new BPF resource monitoring tool [1]. This is caused by the
asymmetry of the allocation/free scheme. While the entry is allocated
upon the first route that requires it, it is only freed during
de-initialization of the driver.
Instead, this patchset tracks the number of active nexthop groups and
allocates the adjacency entry upon the creation of the first group. The
entry is freed when the number of active groups reaches zero.
Patch #1 adds the new entry.
Patch #2 converts mlxsw to start using the new entry and removes the old
one.
====================
mlxsw: spectrum_router: Add trap adjacency entry upon first nexthop group
In commit 0c3cbbf96def ("mlxsw: Add specific trap for packets routed via
invalid nexthops"), mlxsw started allocating a new adjacency entry
during driver initialization, to trap packets routed via invalid
nexthops.
This behavior was later altered in commit 983db6198f0d ("mlxsw:
spectrum_router: Allocate discard adjacency entry when needed") to only
allocate the entry upon the first route that requires it. The motivation
for the change is explained in the commit message.
The problem with the current behavior is that the entry shows up as a
"leak" in a new BPF resource monitoring tool [1]. This is caused by the
asymmetry of the allocation/free scheme. While the entry is allocated
upon the first route that requires it, it is only freed during
de-initialization of the driver.
Instead, track the number of active nexthop groups and allocate the
adjacency entry upon the creation of the first group. Free it when the
number of active groups reaches zero.
The next patch will convert mlxsw to start using the new entry and
remove the old one.
1> Function comments moved to .c file.
2> Use literals in return to improve readability.
3> Do error handling check instead of success check.
4> Redundant ret assignment removed.
Leon Romanovsky [Wed, 22 Sep 2021 08:58:03 +0000 (11:58 +0300)]
devlink: Make devlink_register to be void
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Jakub Kicinski [Wed, 22 Sep 2021 03:02:27 +0000 (20:02 -0700)]
Merge branch 's390-qeth-fixes-2021-09-21'
Julian Wiedmann says:
====================
s390/qeth: fixes 2021-09-21
This brings two fixes for deadlocks when a device is removed while it
has certain types of async work pending. And one additional fix for a
missing NULL check in an error case.
====================
Alexandra Winter [Tue, 21 Sep 2021 14:52:17 +0000 (16:52 +0200)]
s390/qeth: fix deadlock during failing recovery
Commit 0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery") removed
taking discipline_mutex inside qeth_do_reset(), fixing potential
deadlocks. An error path was missed though, that still takes
discipline_mutex and thus has the original deadlock potential.
Intermittent deadlocks were seen when a qeth channel path is configured
offline, causing a race between qeth_do_reset and ccwgroup_remove.
Call qeth_set_offline() directly in the qeth_do_reset() error case and
then a new variant of ccwgroup_set_offline(), without taking
discipline_mutex.
Fixes: b41b554c1ee7 ("s390/qeth: fix locking for discipline setup / removal") Signed-off-by: Alexandra Winter <[email protected]> Reviewed-by: Julian Wiedmann <[email protected]> Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
Alexandra Winter [Tue, 21 Sep 2021 14:52:16 +0000 (16:52 +0200)]
s390/qeth: Fix deadlock in remove_discipline
Problem: qeth_close_dev_handler is a worker that tries to acquire
card->discipline_mutex via drv->set_offline() in ccwgroup_set_offline().
Since commit b41b554c1ee7
("s390/qeth: fix locking for discipline setup / removal")
qeth_remove_discipline() is called under card->discipline_mutex and
cancels the work and waits for it to finish.
STOPLAN reception with reason code IPA_RC_VEPA_TO_VEB_TRANSITION is the
only situation that schedules close_dev_work. In that situation scheduling
qeth recovery will also result in an offline interface, when resetting the
isolation mode fails, if the external switch is still set to VEB.
And since commit 0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery")
qeth recovery does not aquire card->discipline_mutex anymore.
So we accept the longer pathlength of qeth_schedule_recovery in this
error situation and re-use the existing function.
As a side-benefit this changes the hwtrap to behave like during recovery
instead of like during a user-triggered set_offline.
Fixes: b41b554c1ee7 ("s390/qeth: fix locking for discipline setup / removal") Signed-off-by: Alexandra Winter <[email protected]> Acked-by: Julian Wiedmann <[email protected]> Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().
qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).
Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.
Fix it by checking the pointer for NULL before accessing it.
Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.
Mark Brown [Tue, 21 Sep 2021 14:44:06 +0000 (15:44 +0100)]
spi: Revert modalias changes
During the v5.13 cycle we updated the SPI subsystem to generate OF style
modaliases for SPI devices, replacing the old Linux style modalises we
used to generate based on spi_device_id which are the DT style name with
the vendor removed. Unfortunately this means that we start only
reporting OF style modalises and not the old ones and there is nothing
that ensures that drivers list every possible OF compatible string in
their OF ID table. The result is that there are systems which have been
relying on loading modules based on the old style that are now broken,
as found by Russell King with spi-nor on Macchiatobin.
spi-nor is a particularly problematic case for this, it only lists a
single generic DT compatible jedec,spi-nor in the driver but supports a
huge raft of device specific compatibles, with a large set of part
numbers many of which are offered by multiple vendors. Russell's
searches of upstream device trees has turned up examples with vendor
names written in non-standard ways too. To make matters worse up until 8ff16cf77ce3 ("Documentation: devicetree: m25p80: add "nor-jedec"
binding") the generic compatible was not part of the binding so there
are device trees out there written to that binding version which don't
list it all. The sheer number of parts supported together with our
previous approach of ignoring the vendor ID makes robustly fixing this
by adding compatibles to the spi-nor driver seem problematic, the
current DT binding document does not list all the parts supported by the
driver at the minute (further patches will fix this).
I've also investigated supporting both formats of modalias
simultaneously but that doesn't seem possible, especially without
breaking our userspace ABI which is obviously not viable.
This will unfortunately mean that any system which had started having
modules autoload based on the OF compatibles for drivers that list
things there but not in the spi_device_ids will now not have those
modules load which is itself a regression. Since it affects a narrower
time window and the particularly problematic spi-nor driver may be
critical to system boot on smaller systems this seems the best of a
series of bad options. I will start an audit of SPI drivers to identify
and fix cases where things won't autoload using spi_device_id, this is
not great but seems to be the best way forward that anyone has been able
to identify.
Thanks to Russell for both his report and the additional diagnostic and
analysis work he has done here, the detailed research above was his
work.
Fixes: e09f2ab8eecc ("spi: update modalias_show after of_device_uevent_modalias support") Fixes: 3ce6c9e2617e ("spi: add of_device_uevent_modalias support") Reported-by: Russell King (Oracle) <[email protected]> Suggested-by: Russell King (Oracle) <[email protected]> Signed-off-by: Mark Brown <[email protected]> Tested-by: Russell King (Oracle) <[email protected]> Cc: Andreas Schwab <[email protected]> Cc: Marco Felsch <[email protected]>
Merge tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 eBPF fixes from Vasily Gorbik:
"Johan Almbladh has implemented a number of new testcases for eBPF [1],
which uncovered three miscompilation issues in the s390 eBPF JIT"
Link: https://lore.kernel.org/bpf/[email protected]/
* tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/bpf: Fix optimizing out zero-extensions
s390/bpf: Fix 64-bit subtraction of the -0x80000000 constant
s390/bpf: Fix branch shortening during codegen pass
In commit b7213ffa0e58 ("qnx4: avoid stringop-overread errors") I tried
to teach gcc about how the directory entry structure can be two
different things depending on a status flag. It made the code clearer,
and it seemed to make gcc happy.
However, Arnd points to a gcc bug, where despite using two different
members of a union, gcc then gets confused, and uses the size of one of
the members to decide if a string overrun happens. And not necessarily
the rigth one.
End result: with some configurations, gcc-11 will still complain about
the source buffer size being overread:
because gcc will get confused about which union member entry is actually
getting accessed, even when the source code is very clear about it. Gcc
internally will have combined two "redundant" pointers (pointing to
different union elements that are at the same offset), and takes the
size checking from one or the other - not necessarily the right one.
This is clearly a gcc bug, but we can work around it fairly easily. The
biggest thing here is the big honking comment about why we do what we
do.
When DELL_WMI=y, DELL_WMI_PRIVACY=y, and LEDS_TRIGGER_AUDIO=m, there
is a linker error since the LEDS trigger code is built as a loadable
module. This happens because DELL_WMI_PRIVACY is a bool that depends
on a tristate (LEDS_TRIGGER_AUDIO=m), which can be dangerous.
ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
dell-wmi-privacy.c:(.text+0x3df): undefined reference to `ledtrig_audio_get'
David S. Miller [Tue, 21 Sep 2021 12:52:16 +0000 (13:52 +0100)]
Merge branch 'dsa-devres'
Vladimir Oltean says:
====================
Fix mdiobus users with devres
Commit ac3a68d56651 ("net: phy: don't abuse devres in
devm_mdiobus_register()") by Bartosz Golaszewski has introduced two
classes of potential bugs by making the devres callback of
devm_mdiobus_alloc stop calling mdiobus_unregister.
The exact buggy circumstances are presented in the individual commit
messages. I have searched the tree for other occurrences, but at the
moment:
- for issue (a) I have no concrete proof that other buses except SPI and
I2C suffer from it, and the only SPI or I2C device drivers that call
of_mdiobus_alloc are the DSA drivers that leave a NULL
ds->slave_mii_bus and a non-NULL ds->ops->phy_read, aka ksz9477,
ksz8795, lan9303_i2c, vsc73xx-spi.
- for issue (b), all drivers which call of_mdiobus_alloc either use
of_mdiobus_register too, or call mdiobus_unregister sometime within
the ->remove path.
Although at this point I've seen enough strangeness caused by this
"device_del during ->shutdown" that I'm just going to copy the SPI and
I2C subsystem maintainers to this patch series, to get their feedback
whether they've had reports about things like this before. I don't think
other buses behave in this way, it forces SPI and I2C devices to have to
protect themselves from a really strange set of issues.
====================
Vladimir Oltean [Mon, 20 Sep 2021 21:42:09 +0000 (00:42 +0300)]
net: dsa: realtek: register the MDIO bus under devres
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Vladimir Oltean [Mon, 20 Sep 2021 21:42:08 +0000 (00:42 +0300)]
net: dsa: don't allocate the slave_mii_bus using devres
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Mianhan Liu [Tue, 21 Sep 2021 07:47:51 +0000 (15:47 +0800)]
net/ipv4/sysctl_net_ipv4.c: remove superfluous header files from sysctl_net_ipv4.c
sysctl_net_ipv4.c hasn't use any macro or function declared in igmp.h,
inetdevice.h, mm.h, module.h, nsproxy.h, swap.h, inet_frag.h, route.h
and snmp.h. Thus, these files can be removed from sysctl_net_ipv4.c
safely without affecting the compilation of the net module.
Vladimir Oltean [Mon, 20 Sep 2021 22:49:18 +0000 (01:49 +0300)]
net: dsa: fix dsa_tree_setup error path
Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.
However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.
Fixes: a57d8c217aad ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
This patch series adds support for the IDDQ with soft recovery mode
which allows power savings of roughly 150mW compared to a simple
BMCR.PDOWN power off (called standby power down in Broadcom datasheets).
In order to leverage these modes we add a new PHY driver flags for
drivers to opt-in for that behavior, the PHY driver is modified to do
the appropriate programming and the PHYs on which this was tested get
updated to have an appropriate suspend/resume set of functions.
====================
net: phy: broadcom: Utilize appropriate suspend for BCM54810/11
Since we enable APD and DLL/RXC/TXC disable we need to use
bcm54xx_suspend() in order not to do a read/modify/write of the BMCR
register which is incompatible with the desired settings.
Add support for putting the PHY into IDDQ Soft Recovery mode by setting
the TOP_MISC register bits accordingly. This requires us to implement a
custom bcm54xx_suspend() routine which diverges from genphy_suspend() in
order to configure the PHY to enter IDDQ with software recovery as well
as avoid doing a read/modify/write on the BMCR register.
Doing a read/modify/write on the BMCR register means that the
auto-negotation bit may remain which interferes with the ability to put
the PHY into IDDQ-SR mode. We do software reset upon suspend in order to
put the PHY back into its state prior to suspend as recommended by the
datasheet.
net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().
Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().
Fixes: b286a0651e44 ("net/smc: handle incoming CDC validation message") Signed-off-by: Karsten Graul <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Mianhan Liu [Mon, 20 Sep 2021 14:15:49 +0000 (22:15 +0800)]
net/ipv4/syncookies.c: remove superfluous header files from syncookies.c
syncookies.c hasn't use any macro or function declared in slab.h and random.h,
Thus, these files can be removed from syncookies.c safely without
affecting the compilation of the net module.
Mianhan Liu [Mon, 20 Sep 2021 12:29:57 +0000 (20:29 +0800)]
net/ipv4/udp_tunnel_core.c: remove superfluous header files from udp_tunnel_core.c
udp_tunnel_core.c hasn't use any macro or function declared in udp.h, types.h,
and net_namespace.h. Thus, these files can be removed from udp_tunnel_core.c
safely without affecting the compilation of the net module.
Merge tag 'afs-fixes-20210913' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
"Fixes for AFS problems that can cause data corruption due to
interaction with another client modifying data cached locally:
- When d_revalidating a dentry, don't look at the inode to which it
points. Only check the directory to which the dentry belongs. This
was confusing things and causing the silly-rename cleanup code to
remove the file now at the dentry of a file that got deleted.
- Fix mmap data coherency. When a callback break is received that
relates to a file that we have cached, the data content may have
been changed (there are other reasons, such as the user's rights
having been changed). However, we're checking it lazily, only on
entry to the kernel, which doesn't happen if we have a writeable
shared mapped page on that file.
We make the kernel keep track of mmapped files and clear all PTEs
mapping to that file as soon as the callback comes in by calling
unmap_mapping_pages() (we don't necessarily want to zap the
pagecache). This causes the kernel to be reentered when userspace
tries to access the mmapped address range again - and at that point
we can query the server and, if we need to, zap the page cache.
Ideally, I would check each file at the point of notification, but
that involves poking the server[*] - which is holding an exclusive
lock on the vnode it is changing, waiting for all the clients it
notified to reply. This could then deadlock against the server.
Further, invalidating the pagecache might call ->launder_page(),
which would try to write to the file, which would definitely
deadlock. (AFS doesn't lease file access).
[*] Checking to see if the file content has changed is a matter of
comparing the current data version number, but we have to ask
the server for that. We also need to get a new callback promise
and we need to poke the server for that too.
- Add some more points at which the inode is validated, since we're
doing it lazily, notably in ->read_iter() and ->page_mkwrite(), but
also when performing some directory operations.
Ideally, checking in ->read_iter() would be done in some derivation
of filemap_read(). If we're going to call the server to read the
file, then we get the file status fetch as part of that.
- The above is now causing us to make a lot more calls to
afs_validate() to check the inode - and afs_validate() takes the
RCU read lock each time to make a quick check (ie.
afs_check_validity()). This is entirely for the purpose of checking
cb_s_break to see if the server we're using reinitialised its list
of callbacks - however this isn't a very common event, so most of
the time we're taking this needlessly.
Add a new cell-wide counter to count the number of
reinitialisations done by any server and check that - and only if
that changes, take the RCU read lock and check the server list (the
server list may change, but the cell a file is part of won't).
- Don't update vnode->cb_s_break and ->cb_v_break inside the validity
checking loop. The cb_lock is done with read_seqretry, so we might
go round the loop a second time after resetting those values - and
that could cause someone else checking validity to miss something
(I think).
Also included are patches for fixes for some bugs encountered whilst
debugging this:
- Fix a leak of afs_read objects and fix a leak of keys hidden by
that.
- Fix a leak of pages that couldn't be added to extend a writeback.
- Fix the maintenance of i_blocks when i_size is changed by a local
write or a local dir edit"
Merge tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd
Pull ksmbd server fixes from Steve French:
"Three ksmbd fixes, including an important security fix for path
processing, and a buffer overflow check, and a trivial fix for
incorrect header inclusion"
* tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd:
ksmbd: add validation for FILE_FULL_EA_INFORMATION of smb2_get_info
ksmbd: prevent out of share access
ksmbd: transport_rdma: Don't include rwlock.h directly
Merge tag '5.15-rc1-smb3' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
- two deferred close fixes (for bugs found with xfstests 478 and 461)
- a deferred close improvement in rename
- two trivial fixes for incorrect Linux comment formatting of multiple
cifs files (pointed out by automated kernel test robot and
checkpatch)
* tag '5.15-rc1-smb3' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Not to defer close on file when lock is set
cifs: Fix soft lockup during fsstress
cifs: Deferred close performance improvements
cifs: fix incorrect kernel doc comments
cifs: remove pathname for file from SPDX header
Merge tag 'spi-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark BrownL
"This contains a couple of fixes, one fix for handling of zero length
transfers on Rockchip devices and a warning fix which will conflict
with a version you did but cleans up some extra unneeded forward
declarations as well which seems a bit neater"
* tag 'spi-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: tegra20-slink: Declare runtime suspend and resume functions conditionally
spi: rockchip: handle zero length transfers without timing out
Merge tag 'regulator-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small device specific fixes that have been sent since the
merge window, neither of which stands out particularly"
* tag 'regulator-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max14577: Revert "regulator: max14577: Add proper module aliases strings"
regulator: qcom-rpmh-regulator: fix pm8009-1 ldo7 resource name
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
sparc64: fix pci_iounmap() when CONFIG_PCI is not set
Guenter reported [1] that the pci_iounmap() changes remain problematic,
with sparc64 allnoconfig and tinyconfig still not building due to the
header file changes and confusion with the arch-specific pci_iounmap()
implementation.
I'm pretty convinced that sparc should just use GENERIC_IOMAP instead of
doing its own thing, since it turns out that the sparc64 version of
pci_iounmap() is somewhat buggy (see [2]). But in the meantime, this
just fixes the build by avoiding the trivial re-definition of the empty
case.
Yufeng Mo [Wed, 15 Sep 2021 13:52:11 +0000 (21:52 +0800)]
net: hns3: fix a return value error in hclge_get_reset_status()
hclge_get_reset_status() should return the tqp reset status.
However, if the CMDQ fails, the caller will take it as tqp reset
success status by mistake. Therefore, uses a parameters to get
the tqp reset status instead.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yufeng Mo <[email protected]> Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
The input parameters may not be reliable, so check the vlan id before
using it, otherwise may set wrong vlan id into hardware.
Fixes: dc8131d846d4 ("net: hns3: Fix for packet loss due wrong filter config in VLAN tbls") Signed-off-by: liaoguojia <[email protected]> Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Yufeng Mo [Wed, 15 Sep 2021 13:52:09 +0000 (21:52 +0800)]
net: hns3: check queue id range before using
The input parameters may not be reliable. Before using the
queue id, we should check this parameter. Otherwise, memory
overwriting may occur.
Fixes: d34100184685 ("net: hns3: refactor the mailbox message between PF and VF") Signed-off-by: Yufeng Mo <[email protected]> Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: hns3: fix misuse vf id and vport id in some logs
vport_id include PF and VFs, vport_id = 0 means PF, other values mean VFs.
So the actual vf id is equal to vport_id minus 1.
Some VF print logs are actually vport, and logs of vf id actually use
vport id, so this patch fixes them.
Fixes: ac887be5b0fe ("net: hns3: change print level of RAS error log from warning to error") Fixes: adcf738b804b ("net: hns3: cleanup some print format warning") Signed-off-by: Jiaran Zhang <[email protected]> Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
The vf id from ethtool is added 1 before configured to driver.
So it's necessary to minus 1 when printing it, in order to
keep consistent with user's configuration.
Fixes: dd74f815dd41 ("net: hns3: Add support for rule add/delete for flow director") Signed-off-by: Jian Shen <[email protected]> Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
When user change rss 'hfunc' without set rss 'hkey' by ethtool
-X command, the driver will ignore the 'hfunc' for the hkey is
NULL. It's unreasonable. So fix it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Fixes: 374ad291762a ("net: hns3: Add RSS general configuration support for VF") Signed-off-by: Jian Shen <[email protected]> Signed-off-by: Guangbin Huang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
projects / linux.git / log