Linus Torvalds [Mon, 2 Jun 2014 19:15:19 +0000 (12:15 -0700)]
Merge tag 'pci-v3.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into next
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Notify driver before and after device reset (Keith Busch)
- Use reset notification in NVMe (Keith Busch)
NUMA
- Warn if we have to guess host bridge node information (Myron Stowe)
- Work around AMD Fam15h BIOSes that fail to provide _PXM (Suravee
Suthikulpanit)
- Clean up and mark early_root_info_init() as deprecated (Suravee
Suthikulpanit)
Driver binding
- Add "driver_override" for force specific binding (Alex Williamson)
- Fail "new_id" addition for devices we already know about (Bandan
Das)
Resource management
- Support BAR sizes up to 8GB (Nikhil Rao, Alan Cox)
- Don't move IORESOURCE_PCI_FIXED resources (Bjorn Helgaas)
- Mark SBx00 HPET BAR as IORESOURCE_PCI_FIXED (Bjorn Helgaas)
- Fail safely if we can't handle BARs larger than 4GB (Bjorn Helgaas)
- Reject BAR above 4GB if dma_addr_t is too small (Bjorn Helgaas)
- Don't convert BAR address to resource if dma_addr_t is too small
(Bjorn Helgaas)
- Don't set BAR to zero if dma_addr_t is too small (Bjorn Helgaas)
- Don't print anything while decoding is disabled (Bjorn Helgaas)
- Don't add disabled subtractive decode bus resources (Bjorn Helgaas)
- Add resource allocation comments (Bjorn Helgaas)
- Restrict 64-bit prefetchable bridge windows to 64-bit resources
(Yinghai Lu)
- Assign i82875p_edac PCI resources before adding device (Yinghai Lu)
PCI device hotplug
- Remove unnecessary "dev->bus" test (Bjorn Helgaas)
- Use PCI_EXP_SLTCAP_PSN define (Bjorn Helgaas)
- Fix rphahp endianess issues (Laurent Dufour)
- Acknowledge spurious "cmd completed" event (Rajat Jain)
- Allow hotplug service drivers to operate in polling mode (Rajat Jain)
- Fix cpqphp possible NULL dereference (Rickard Strandqvist)
MSI
- Replace pci_enable_msi_block() by pci_enable_msi_exact()
(Alexander Gordeev)
- Replace pci_enable_msix() by pci_enable_msix_exact() (Alexander Gordeev)
- Simplify populate_msi_sysfs() (Jan Beulich)
Virtualization
- Add Intel Patsburg (X79) root port ACS quirk (Alex Williamson)
- Mark RTL8110SC INTx masking as broken (Alex Williamson)
Freescale i.MX6
- Use new clock names (Lucas Stach)
- Drop old IRQ mapping (Lucas Stach)
- Remove optional (and unused) IRQs (Lucas Stach)
- Add support for MSI (Lucas Stach)
- Fix imx6_add_pcie_port() section mismatch warning (Sachin Kamat)
Renesas R-Car
- Add gen2 device tree support (Ben Dooks)
- Use new OF interrupt mapping when possible (Lucas Stach)
- Add PCIe driver (Phil Edworthy)
- Add PCIe MSI support (Phil Edworthy)
- Add PCIe device tree bindings (Phil Edworthy)
Linus Torvalds [Mon, 2 Jun 2014 16:29:34 +0000 (09:29 -0700)]
Merge branch 'for-3.16/core' of git://git.kernel.dk/linux-block into next
Pull block core updates from Jens Axboe:
"It's a big(ish) round this time, lots of development effort has gone
into blk-mq in the last 3 months. Generally we're heading to where
3.16 will be a feature complete and performant blk-mq. scsi-mq is
progressing nicely and will hopefully be in 3.17. A nvme port is in
progress, and the Micron pci-e flash driver, mtip32xx, is converted
and will be sent in with the driver pull request for 3.16.
This pull request contains:
- Lots of prep and support patches for scsi-mq have been integrated.
All from Christoph.
- API and code cleanups for blk-mq from Christoph.
- Lots of good corner case and error handling cleanup fixes for
blk-mq from Ming Lei.
- A flew of blk-mq updates from me:
* Provide strict mappings so that the driver can rely on the CPU
to queue mapping. This enables optimizations in the driver.
* Provided a bitmap tagging instead of percpu_ida, which never
really worked well for blk-mq. percpu_ida relies on the fact
that we have a lot more tags available than we really need, it
fails miserably for cases where we exhaust (or are close to
exhausting) the tag space.
* Provide sane support for shared tag maps, as utilized by scsi-mq
* Various fixes for IO timeouts.
* API cleanups, and lots of perf tweaks and optimizations.
- Remove 'buffer' from struct request. This is ancient code, from
when requests were always virtually mapped. Kill it, to reclaim
some space in struct request. From me.
- Remove 'magic' from blk_plug. Since we store these on the stack
and since we've never caught any actual bugs with this, lets just
get rid of it. From me.
- Only call part_in_flight() once for IO completion, as includes two
atomic reads. Hopefully we'll get a better implementation soon, as
the part IO stats are now one of the more expensive parts of doing
IO on blk-mq. From me.
- File migration of block code from {mm,fs}/ to block/. This
includes bio.c, bio-integrity.c, bounce.c, and ioprio.c. From me,
from a discussion on lkml.
That should describe the meat of the pull request. Also has various
little fixes and cleanups from Dave Jones, Shaohua Li, Duan Jiong,
Fengguang Wu, Fabian Frederick, Randy Dunlap, Robert Elliott, and Sam
Bradshaw"
* 'for-3.16/core' of git://git.kernel.dk/linux-block: (100 commits)
blk-mq: push IPI or local end_io decision to __blk_mq_complete_request()
blk-mq: remember to start timeout handler for direct queue
block: ensure that the timer is always added
blk-mq: blk_mq_unregister_hctx() can be static
blk-mq: make the sysfs mq/ layout reflect current mappings
blk-mq: blk_mq_tag_to_rq should handle flush request
block: remove dead code in scsi_ioctl:blk_verify_command
blk-mq: request initialization optimizations
block: add queue flag for disabling SG merging
block: remove 'magic' from struct blk_plug
blk-mq: remove alloc_hctx and free_hctx methods
blk-mq: add file comments and update copyright notices
blk-mq: remove blk_mq_alloc_request_pinned
blk-mq: do not use blk_mq_alloc_request_pinned in blk_mq_map_request
blk-mq: remove blk_mq_wait_for_tags
blk-mq: initialize request in __blk_mq_alloc_request
blk-mq: merge blk_mq_alloc_reserved_request into blk_mq_alloc_request
blk-mq: add helper to insert requests from irq context
blk-mq: remove stale comment for blk_mq_complete_request()
blk-mq: allow non-softirq completions
...
Linus Torvalds [Mon, 2 Jun 2014 16:22:24 +0000 (09:22 -0700)]
Merge tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc into next
Pull MMC update from Ulf Hansson:
"These patches are mainly updates for the mmci driver and have been
tested in linux-next.
Some ARM SoC related patches are also included and those have been
acked from the corresponding maintainers to go through my mmc tree.
Updates for mmci driver:
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data"
* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
mmc: mmci: Enforce DMA configuration through DT
mmc: mmci: Enforce max frequency configuration through DT
mmc: mmci: Enforce mmc capabilities through DT
mmc: mmci: Enforce DT for signal direction and feedback clock
ARM: ux500: Remove redundant board file for mmci platform data
ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
ARM: ux500: Add the mmc capabilities flags to DT
mmc: mmci: Enable MMC_CAP_CMD23
mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
ARM: u300: Convert to the common mmc DT bindings for highspeed mode
ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Add mmci signal directions and feeback clock in DT for href
mmc: mmci: Use the common mmc DT parser
mmc: mmci: Add DT bindings for feedback clock pin
mmc: mmci: Add DT bindings for signal direction
mmc: mmci: Update DT documentation
mmc: mmci: Convert to devm functions
mmc: mmci: Convert to the mmc gpio API
mmc: mmci: Put the device into low power state at system suspend
...
Linus Torvalds [Mon, 2 Jun 2014 16:13:58 +0000 (09:13 -0700)]
Merge tag 'hsi-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi into next
Pull HSI (High Speed Syncronous Interface) changes from Sebastian Reichel:
"Please pull the following changes for the HSI subsystem, which I have
taken over from Carlos Chinea <[email protected]>.
The below patches have been worked on in the linux-omap mailinglist
for 10 months and are well tested in linux-next (have been in there
for more than two weeks) without any problems arising. Apart from
that potential regressions are very limited, because the subsystem is
not yet used by any platform in the mainline kernel.
- Add some documentation for the HSI subsystem
- Add Device Tree support for the HSI subsystem
- Add OMAP3 SSI driver (SSI is a legacy variant of HSI)
- Add Nokia N900 Modem driver (without speech support for now)"
* tag 'hsi-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
HSI: Introduce Nokia N900 modem driver
HSI: Introduce driver for SSI Protocol
Documentation: DT: omap-ssi binding documentation
HSI: Introduce OMAP SSI driver
HSI: Add common DT binding for HSI client devices
HSI: export method to (un)register clients
HSI: Add channel resource support to HSI clients
HSI: method to unregister clients from an hsi port
HSI: hsi-char: fix driver for multiport scenarios
MAINTAINERS: update HSI entry
Documentation: HSI: Add some general description for the HSI subsystem
Linus Torvalds [Mon, 2 Jun 2014 15:46:03 +0000 (08:46 -0700)]
Merge tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.16 series.
There is a lot of action in the GPIO subsystem doing refactorings and
cleanups, almost as many deletions as insertions and minor feature
growth and no new drivers this time. Which is actually pretty nice.
Some GPIO-related stuff will come in through the pin control tree as
well.
Details:
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib core and
avoiding duplicate code and, more importantly, duplicate bug fixes:
* Support for using the helpers with threaded interrupt handlers as
used on sleeping GPIO-irqchips
* Do not set up hardware triggers for edges or levels if the
default IRQ type is IRQ_TYPE_NONE - some drivers would exploit
the fact that you could get default initialization of the IRQ
type from the core at probe() but if no default type is set up
from the helper, we should not call the driver to configure
anything. Wait until a consumer requests the interrupt instead.
* Make the irqchip helpers put the GPIO irqs into their own lock
class. The GPIO irqchips can often emit (harmless, but annoying)
lockdep warnings about recursions when they are in fact just
cascaded IRQs. By putting them into their own lock class we help
the lockdep core to keep track of things.
* Switch the tc3589x GPIO expanders to use the irqchip helpers
* Switch the OMAP GPIO driver to use the irqchip helpers
* Add some documentation for the irqchip helpers
* select IRQ_DOMAIN when using the helpers since some platforms may
not be using this by default and it's a strict dependency.
- Continued GPIO descriptor refactoring:
* Remove the one instance of gpio_to_desc() from the device tree
code, making the OF GPIO code use GPIO descriptors only.
* Introduce gpiod_get_optional() and gpiod_get_optional_index()
akin to the similar regulator functions for cases where the use
of GPIO is optional and not strictly required.
* Make of_get_named_gpiod_flags() private - we do not want to
unnecessarily expose APIs to drivers that make the gpiolib harder
than necessary to maintain and refactor. Privatize this
function.
- Support "-gpio" suffix for the OF GPIO retrieveal path. We used to
look for "foo-gpios" or just "gpios" in device tree nodes, but it
turns out that some drivers with a single GPIO line will just state
"foo-gpio" (singularis). Sigh. Support this with a fallback
looking for it, as this simplifies driver code and handles it in
core code.
- Switch the ACPI GPIO core to fetch GPIOs with the *_cansleep
function variants as the GPIO operation region handler can sleep,
and shall be able to handle gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han, Axel Lin,
Javier Martinez Canillas and Abdoulaye Berthe. Notably Jingoo cut
off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers, nothing
really special here"
* tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
gpio: pca953x: use gpiolib irqchip helpers
gpio: pcf857x: Add IRQF_SHARED when request irq
gpio: pcf857x: Avoid calling irq_domain_cleanup twice
gpio: mcp23s08: switch chip count to int
gpio: dwapb: use a second irq chip
gpio: ep93xx: Use devm_ioremap_resource()
gpio: mcp23s08: fixed count variable for devicetree probing
gpio: Add run-time dependencies to R-Car driver
gpio: pch: add slab include
Documentation / ACPI: Fix location of GPIO documentation
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
gpio: generic: add request function pointer
gpio-pch: Fix Kconfig dependencies
gpio: make of_get_named_gpiod_flags() private
gpio: gpioep93xx: use devm functions
gpio: janzttl: use devm function
gpio: timberdale: use devm functions
gpio: bt8xx: use devm function for memory allocation
gpio: include linux/bug.h in interface header
...
Linus Torvalds [Mon, 2 Jun 2014 15:24:12 +0000 (08:24 -0700)]
Merge tag 'stable/for-linus-3.16-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip into next
Pull Xen updates from David Vrabel:
"xen: features and fixes for 3.16-rc0
- support foreign mappings in PVH domains (needed when dom0 is PVH)
- fix mapping high MMIO regions in x86 PV guests (this is also the
first half of removing the PAGE_IOMAP PTE flag).
- ARM suspend/resume support.
- ARM multicall support"
* tag 'stable/for-linus-3.16-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: map foreign pfns for autotranslated guests
xen-acpi-processor: Don't display errors when we get -ENOSYS
xen/pciback: Document the entry points for 'pcistub_put_pci_dev'
xen/pciback: Document when the 'unbind' and 'bind' functions are called.
xen-pciback: Document when we FLR an PCI device.
xen-pciback: First reset, then free.
xen-pciback: Cleanup up pcistub_put_pci_dev
x86/xen: do not use _PAGE_IOMAP in xen_remap_domain_mfn_range()
x86/xen: set regions above the end of RAM as 1:1
x86/xen: only warn once if bad MFNs are found during setup
x86/xen: compactly store large identity ranges in the p2m
x86/xen: fix set_phys_range_identity() if pfn_e > MAX_P2M_PFN
x86/xen: rename early_p2m_alloc() and early_p2m_alloc_middle()
xen/x86: set panic notifier priority to minimum
arm,arm64/xen: introduce HYPERVISOR_suspend()
xen: refactor suspend pre/post hooks
arm: xen: export HYPERVISOR_multicall to modules.
arm64: introduce virt_to_pfn
arm/xen: Remove definiition of virt_to_pfn in asm/xen/page.h
arm: xen: implement multicall hypercall support.
Linus Torvalds [Mon, 2 Jun 2014 15:03:34 +0000 (08:03 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k into next
Pull m68k updates from Geert Uytterhoeven:
"Highlights:
- support for running kernels in fast TT-RAM instead of slow ST-RAM
on Atari
- multi-platform EARLY_PRINTK
- better support for machines with lots of RAM (think ARAnyM), and
for running kernels larger than 4 MiB (think multi-platform)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/hp300: Convert printk to pr_foo()
m68k/apollo: Convert printk to pr_foo()
m68k/amiga: Convert printk(foo to pr_foo()
m68k: Increase initial mapping to 8 or 16 MiB if possible
m68k: Update defconfigs for v3.15-rc2
m68k/atari: fix SCC initialization for debug console
m68k/mvme16x: Adopt common boot console
m68k: Multi-platform EARLY_PRINTK
m68k: Toward platform agnostic framebuffer debug logging
m68k/atari - atari_scsi: use correct virt/phys translation for DMA buffer
m68k/atari - ataflop: use correct virt/phys translation for DMA buffer
m68k/atari - atafb: convert allocation of fb ram to new interface
m68k/atari - stram: alloc ST-RAM pool even if kernel not in ST-RAM
Linus Torvalds [Mon, 2 Jun 2014 01:28:58 +0000 (18:28 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of fixes across the field. Nothing terribly
complicated; the one liners in below changelog should be fairly
descriptive.
Noteworthy is the SB1 change which the result of changes to binutils
resulting in one big gas warning for most files being assembled as
well as the asid_cache and branch emulation fixes which fix corruption
or possible uninteded behaviour of kernel or application code. The
remainder of fixes are more platforms or subsystem specific"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: R46000: Fix Micro-assembler field overflow for R4600 V2
MIPS: ptrace: Avoid smp_processor_id() in preemptible code
MIPS: Lemote 2F: cs5536: mfgpt: use raw locks
MIPS: SB1: Fix excessive kernel warnings.
MIPS: RC32434: fix broken PCI resource initialization
MIPS: malta: memory.c: Initialize the 'memsize' variable
MIPS: Fix typo when reporting cache and ftlb errors for ImgTec cores
MIPS: Fix inconsistancy of __NR_Linux_syscalls value
MIPS: Fix branch emulation of branch likely instructions.
MIPS: Fix a typo error in AUDIT_ARCH definition
MIPS: Change type of asid_cache to unsigned long
Linus Torvalds [Mon, 2 Jun 2014 01:26:59 +0000 (18:26 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Various fixlets, mostly related to the (root-only) SCHED_DEADLINE
policy, but also a hotplug bug fix and a fix for a NR_CPUS related
overallocation bug causing a suspend/resume regression"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix hotplug vs. set_cpus_allowed_ptr()
sched/cpupri: Replace NR_CPUS arrays
sched/deadline: Replace NR_CPUS arrays
sched/deadline: Restrict user params max value to 2^63 ns
sched/deadline: Change sched_getparam() behaviour vs SCHED_DEADLINE
sched: Disallow sched_attr::sched_policy < 0
sched: Make sched_setattr() correctly return -EFBIG
Linus Torvalds [Sat, 31 May 2014 16:47:55 +0000 (09:47 -0700)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core futex/rtmutex fixes from Thomas Gleixner:
"Three fixlets for long standing issues in the futex/rtmutex code
unearthed by Dave Jones syscall fuzzer:
- Add missing early deadlock detection checks in the futex code
- Prevent user space from attaching a futex to kernel threads
- Make the deadlock detector of rtmutex work again
Looks large, but is more comments than code change"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Fix deadlock detector for real
futex: Prevent attaching to kernel threads
futex: Add another early deadlock detection check
Linus Torvalds [Sat, 31 May 2014 16:19:02 +0000 (09:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Mostly quiet now:
i915:
fixing userspace visiblie issues, all stable marked
radeon:
one more pll fix, two crashers, one suspend/resume regression"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Resume fbcon last
drm/radeon: only allocate necessary size for vm bo list
drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submission
drm/radeon: avoid crash if VM command submission isn't available
drm/radeon: lower the ref * post PLL maximum once more
drm/i915: Prevent negative relocation deltas from wrapping
drm/i915: Only copy back the modified fields to userspace from execbuffer
drm/i915: Fix dynamic allocation of physical handles
Linus Torvalds [Sat, 31 May 2014 16:13:21 +0000 (09:13 -0700)]
dcache: add missing lockdep annotation
lock_parent() very much on purpose does nested locking of dentries, and
is careful to maintain the right order (lock parent first). But because
it didn't annotate the nested locking order, lockdep thought it might be
a deadlock on d_lock, and complained.
Add the proper annotation for the inner locking of the child dentry to
make lockdep happy.
Introduced by commit 046b961b45f9 ("shrink_dentry_list(): take parent's
->d_lock earlier").
Jens Axboe [Sat, 31 May 2014 03:20:50 +0000 (21:20 -0600)]
blk-mq: push IPI or local end_io decision to __blk_mq_complete_request()
We have callers outside of the blk-mq proper (like timeouts) that
want to call __blk_mq_complete_request(), so rename the function
and put the decision code for whether to use ->softirq_done_fn
or blk_mq_endio() into __blk_mq_complete_request().
This also makes the interface more logical again.
blk_mq_complete_request() attempts to atomically mark the request
completed, and calls __blk_mq_complete_request() if successful.
__blk_mq_complete_request() then just ends the request.
which was merged long ago and actually part of 3.14.
Digging deeper I've noticed (again) that the call to
drm_helper_resume_force_mode in the radeon resume handlers was a no-op
previously because everything gets shut down on suspend. radeon does
this with explicit calls to drm_helper_connector_dpms with DPMS_OFF.
But with 177c we now force the dpms state to ON, so suddenly
resume_force_mode actually forced the crtcs back on.
This is the intention of the change after all, the problem is that
radeon resumes the fbdev console layer _before_ restoring the display,
through calling fb_set_suspend. And fbcon does an immediate ->set_par,
which in turn causes the same forced mode restore to happen.
Two concurrent modeset operations didn't lead to happiness. Fix this
by delaying the fbcon resume until the end of the readeon resum
functions.
v2: Fix up a bit of the spelling fail.
References: https://lkml.org/lkml/2014/5/29/1043
References: https://lkml.org/lkml/2014/5/2/388
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=74751 Tested-by: Ken Moffat <[email protected]> Cc: Alex Deucher <[email protected]> Cc: Ken Moffat <[email protected]> Signed-off-by: Daniel Vetter <[email protected]> Signed-off-by: Dave Airlie <[email protected]>
Dave Airlie [Fri, 30 May 2014 23:19:05 +0000 (09:19 +1000)]
Merge branch 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux into drm-fixes
this is the next pull request for stashed up radeon fixes for 3.15. This is finally calming down with only four patches in this pull request.
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: only allocate necessary size for vm bo list
drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submission
drm/radeon: avoid crash if VM command submission isn't available
drm/radeon: lower the ref * post PLL maximum once more
Jens Axboe [Fri, 30 May 2014 21:42:56 +0000 (15:42 -0600)]
blk-mq: remember to start timeout handler for direct queue
Commit 07068d5b8e added a direct-to-hw-queue mode, but this mode
needs to remember to add the request timeout handler as well.
Without it, we don't track timeouts for these requests.
Linus Torvalds [Fri, 30 May 2014 19:07:48 +0000 (12:07 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"A couple of driver/build fixups and also redone quirk for Synaptics
touchpads on Lenovo boxes (now using PNP IDs instead of DMI data to
limit number of quirks)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - change min/max quirk table to pnp-id matching
Input: synaptics - add a matches_pnp_id helper function
Input: synaptics - T540p - unify with other LEN0034 models
Input: synaptics - add min/max quirk for the ThinkPad W540
Input: ambakmi - request a shared interrupt for AMBA KMI devices
Input: pxa27x-keypad - fix generating scancode
Input: atmel-wm97xx - only build for AVR32
Input: fix ps2/serio module dependency
Linus Torvalds [Fri, 30 May 2014 19:06:15 +0000 (12:06 -0700)]
Merge tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Stefan Richter:
"A regression fix for the IEEE 1394 subsystem: re-enable IRQ-based
asynchronous request reception at addresses below 128 TB"
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: revert to 4 GB RDMA, fix protocols using Memory Space
Linus Torvalds [Fri, 30 May 2014 19:04:56 +0000 (12:04 -0700)]
Merge tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A dm-cache stable fix to split discards on cache block boundaries
because dm-cache cannot yet handle discards that span cache blocks.
Really fix a dm-mpath LOCKDEP warning that was introduced in -rc1.
Add a 'no_space_timeout' control to dm-thinp to restore the ability to
queue IO indefinitely when no data space is available. This fixes a
change in behavior that was introduced in -rc6 where the timeout
couldn't be disabled"
* tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: really fix lockdep warning
dm cache: always split discards on cache block boundaries
dm thin: add 'no_space_timeout' dm-thin-pool module param
Minchan Kim [Wed, 28 May 2014 06:53:59 +0000 (15:53 +0900)]
x86_64: expand kernel stack to 16K
While I play inhouse patches with much memory pressure on qemu-kvm,
3.14 kernel was randomly crashed. The reason was kernel stack overflow.
When I investigated the problem, the callstack was a little bit deeper
by involve with reclaim functions but not direct reclaim path.
I tried to diet stack size of some functions related with alloc/reclaim
so did a hundred of byte but overflow was't disappeard so that I encounter
overflow by another deeper callstack on reclaim/allocator path.
Of course, we might sweep every sites we have found for reducing
stack usage but I'm not sure how long it saves the world(surely,
lots of developer start to add nice features which will use stack
agains) and if we consider another more complex feature in I/O layer
and/or reclaim path, it might be better to increase stack size(
meanwhile, stack usage on 64bit machine was doubled compared to 32bit
while it have sticked to 8K. Hmm, it's not a fair to me and arm64
already expaned to 16K. )
So, my stupid idea is just let's expand stack size and keep an eye
toward stack consumption on each kernel functions via stacktrace of ftrace.
For example, we can have a bar like that each funcion shouldn't exceed 200K
and emit the warning when some function consumes more in runtime.
Of course, it could make false positive but at least, it could make a
chance to think over it.
I guess this topic was discussed several time so there might be
strong reason not to increase kernel stack size on x86_64, for me not
knowing so Ccing x86_64 maintainers, other MM guys and virtio
maintainers.
Here's an example call trace using up the kernel stack:
[ Note: the problem is exacerbated by certain gcc versions that seem to
generate much bigger stack frames due to apparently bad coalescing of
temporaries and generating too many spills. Rusty saw gcc-4.6.4 using
35% more stack on the virtio path than 4.8.2 does, for example.
Minchan not only uses such a bad gcc version (4.6.3 in his case), but
some of the stack use is due to debugging (CONFIG_DEBUG_PAGEALLOC is
what causes that kernel_map_pages() frame, for example). But we're
clearly getting too close.
The VM code also seems to have excessive stack frames partly for the
same compiler reason, triggered by excessive inlining and lots of
function arguments.
We need to improve on our stack use, but in the meantime let's do this
simple stack increase too. Unlike most earlier reports, there is
nothing simple that stands out as being really horribly wrong here,
apart from the fact that the stack frames are just bigger than they
should need to be. - Linus ]
Add support for a generic PCI host controller, such as a
firmware-initialised device with static windows or an emulation by
something such as kvmtool.
The controller itself has no configuration registers and has its address
spaces described entirely by the device-tree (using the bindings from
ePAPR). Both CAM and ECAM are supported for Config Space accesses.
Add corresponding documentation for the DT binding.
[bhelgaas: currently uses the ARM-specific pci_common_init_dev() interface] Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Bjorn Helgaas <[email protected]> Reviewed-by: Liviu Dudau <[email protected]>
Lucas Stach [Fri, 28 Mar 2014 16:52:58 +0000 (17:52 +0100)]
PCI: designware: Make MSI ISR shared IRQ aware
On i.MX6 the host controller MSI IRQ is shared with PCI legacy INTD. Make
sure we don't bail too early from the IRQ handler.
The issue is fairly theoretical as it would require a system setup with a
PCIe switch where one connected device is using legacy INTD and another one
using MSI, but better fix it now.
Linus Torvalds [Fri, 30 May 2014 16:52:55 +0000 (09:52 -0700)]
Merge branch 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs dcache livelock fix from Al Viro:
"Fixes for livelocks in shrink_dentry_list() introduced by fixes to
shrink list corruption; the root cause was that trylock of parent's
->d_lock could be disrupted by d_walk() happening on other CPUs,
resulting in shrink_dentry_list() making no progress *and* the same
d_walk() being called again and again for as long as
shrink_dentry_list() doesn't get past that mess.
The solution is to have shrink_dentry_list() treat that trylock
failure not as 'try to do the same thing again', but 'lock them in the
right order'"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
dentry_kill() doesn't need the second argument now
dealing with the rest of shrink_dentry_list() livelock
shrink_dentry_list(): take parent's ->d_lock earlier
expand dentry_kill(dentry, 0) in shrink_dentry_list()
split dentry_kill()
lift the "already marked killed" case into shrink_dentry_list()
Murali Karicheri [Wed, 28 May 2014 17:14:53 +0000 (13:14 -0400)]
ARM/PCI: Call pcie_bus_configure_settings() to set MPS
Call pcie_bus_configure_settings() on ARM, like for other platforms.
pcie_bus_configure_settings() makes sure the MPS across the bus is uniform
and provides the ability to tune the MRSS and MPS to higher performance
values. This is particularly important for embedded where there is no
firmware to program these PCIe settings for the OS.
imx6_add_pcie_port() is called only from from imx6_pcie_probe() which is
annotated with __init. Thus it makes sense to annotate
imx6_add_pcie_port() with __init to avoid section mismatch warnings.
Yijing Wang [Fri, 30 May 2014 03:01:03 +0000 (11:01 +0800)]
PCI: Make pci_bus_add_device() void
pci_bus_add_device() always returns 0, so there's no point in returning
anything at all. Make it a void function and remove the tests of the
return value from the callers.
[bhelgaas: changelog, remove unused "err" from i82875p_setup_overfl_dev()] Signed-off-by: Yijing Wang <[email protected]> Signed-off-by: Bjorn Helgaas <[email protected]>
Al Viro [Thu, 29 May 2014 13:11:45 +0000 (09:11 -0400)]
dealing with the rest of shrink_dentry_list() livelock
We have the same problem with ->d_lock order in the inner loop, where
we are dropping references to ancestors. Same solution, basically -
instead of using dentry_kill() we use lock_parent() (introduced in the
previous commit) to get that lock in a safe way, recheck ->d_count
(in case if lock_parent() has ended up dropping and retaking ->d_lock
and somebody managed to grab a reference during that window), trylock
the inode->i_lock and use __dentry_kill() to do the rest.
Al Viro [Thu, 29 May 2014 12:54:52 +0000 (08:54 -0400)]
shrink_dentry_list(): take parent's ->d_lock earlier
The cause of livelocks there is that we are taking ->d_lock on
dentry and its parent in the wrong order, forcing us to use
trylock on the parent's one. d_walk() takes them in the right
order, and unfortunately it's not hard to create a situation
when shrink_dentry_list() can't make progress since trylock
keeps failing, and shrink_dcache_parent() or check_submounts_and_drop()
keeps calling d_walk() disrupting the very shrink_dentry_list() it's
waiting for.
Solution is straightforward - if that trylock fails, let's unlock
the dentry itself and take locks in the right order. We need to
stabilize ->d_parent without holding ->d_lock, but that's doable
using RCU. And we'd better do that in the very beginning of the
loop in shrink_dentry_list(), since the checks on refcount, etc.
would need to be redone anyway.
That deals with a half of the problem - killing dentries on the
shrink list itself. Another one (dropping their parents) is
in the next commit.
locking parent is interesting - it would be easy to do rcu_read_lock(),
lock whatever we think is a parent, lock dentry itself and check
if the parent is still the right one. Except that we need to check
that *before* locking the dentry, or we are risking taking ->d_lock
out of order. Fortunately, once the D1 is locked, we can check if
D2->d_parent is equal to D1 without the need to lock D2; D2->d_parent
can start or stop pointing to D1 only under D1->d_lock, so taking
D1->d_lock is enough. In other words, the right solution is
rcu_read_lock/lock what looks like parent right now/check if it's
still our parent/rcu_read_unlock/lock the child.
Jens Axboe [Fri, 30 May 2014 14:25:36 +0000 (08:25 -0600)]
blk-mq: make the sysfs mq/ layout reflect current mappings
Currently blk-mq registers all the hardware queues in sysfs,
regardless of whether it uses them (e.g. they have CPU mappings)
or not. The unused hardware queues lack the cpux/ directories,
and the other sysfs entries (like active, pending, etc) are all
zeroes.
Change this so that sysfs correctly reflects the current mappings
of the hardware queues.
Shaohua Li [Fri, 30 May 2014 14:06:42 +0000 (08:06 -0600)]
blk-mq: blk_mq_tag_to_rq should handle flush request
flush request is special, which borrows the tag from the parent
request. Hence blk_mq_tag_to_rq needs special handling to return
the flush request from the tag.
add_pcie_port() is called only from exynos_pcie_probe(), which is annotated
with __init. Thus it makes sense to annotate add_pcie_port() with __init
to avoid the following section mismatch warning:
WARNING: drivers/pci/built-in.o(.text.unlikely+0xf8): Section mismatch in reference from the function add_pcie_port() to the function .init.text:dw_pcie_host_init()
The function add_pcie_port() references
the function __init dw_pcie_host_init().
This is often because add_pcie_port lacks a __init
annotation or the annotation of dw_pcie_host_init is wrong.
Linus Torvalds [Thu, 29 May 2014 21:14:43 +0000 (14:14 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix CoW regression for transparent hugepages by routing set_pmd_at to
set_pte_at, which correctly handles PTE_WRITE and will mark the
resulting table entry as read-only where appropriate"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix pmd_write CoW brokenness
Linus Torvalds [Thu, 29 May 2014 21:05:57 +0000 (14:05 -0700)]
Merge tag 'pm+acpi-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are three stable-candidate fixes, one for the ACPI thermal
driver and two for cpufreq drivers.
Specifics:
- A workqueue is destroyed too early during the ACPI thermal driver
module unload which leads to a NULL pointer dereference in the
driver's remove callback. Fix from Aaron Lu.
- A wrong argument is passed to devm_regulator_get_optional() in the
probe routine of the cpu0 cpufreq driver which leads to resource
leaks if the driver is unbound from the cpufreq platform device.
Fix from Lucas Stach.
- A lock is missing in cpufreq_governor_dbs() which leads to memory
corruption and NULL pointer dereferences during system
suspend/resume, for example. Fix from Bibek Basu"
* tag 'pm+acpi-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / thermal: fix workqueue destroy order
cpufreq: cpu0: drop wrong devm usage
cpufreq: remove race while accessing cur_policy
Linus Torvalds [Thu, 29 May 2014 20:59:18 +0000 (13:59 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock fixes from Mike Turquette:
"Small number of user-visible regression fixes for clock drivers.
There is a memory leak fix for an ST platform, an infinite Loop Of
Doom fix for the recent changes to the basic clock divider (hopefully
the last fix for those recent changes) and some Tegra PLL changes
which keep PCI from being hosed on that platform"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: st: Fix memory leak
clk: divider: Fix table round up function
clk: tegra: Fix enabling of PLLE
clk: tegra: Introduce divider mask and shift helpers
clk: tegra: Fix PLLE programming
Jens Axboe [Thu, 29 May 2014 17:00:11 +0000 (11:00 -0600)]
blk-mq: request initialization optimizations
We currently clear a lot more than we need to, so make that a bit
more clever. Make some of the init dependent on features, like
only setting start_time if we are going to use it.
Jens Axboe [Thu, 29 May 2014 15:53:32 +0000 (09:53 -0600)]
block: add queue flag for disabling SG merging
If devices are not SG starved, we waste a lot of time potentially
collapsing SG segments. Enough that 1.5% of the CPU time goes
to this, at only 400K IOPS. Add a queue flag, QUEUE_FLAG_NO_SG_MERGE,
which just returns the number of vectors in a bio instead of looping
over all segments and checking for collapsible ones.
Add a BLK_MQ_F_SG_MERGE flag so that drivers can opt-in on the sg
merging, if they so desire.
Linus Walleij [Thu, 29 May 2014 14:52:46 +0000 (16:52 +0200)]
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
These helpers depend on the IRQ_DOMAIN so select it explicitly,
as it will not be present on all platforms such as Intel
desktops and laptops using Intel-MID.
Jens Axboe [Thu, 29 May 2014 14:09:00 +0000 (08:09 -0600)]
block: remove 'magic' from struct blk_plug
I don't think we've ever caught any bugs with this, and there's the
list poisoning for the plug lists to catch uninitialized cases.
So remove the magic member and save 8 bytes in the struct.
Stefan Richter [Thu, 29 May 2014 13:23:26 +0000 (15:23 +0200)]
firewire: revert to 4 GB RDMA, fix protocols using Memory Space
Undo a feature introduced in v3.14 by commit fcd46b34425d
"firewire: Enable remote DMA above 4 GB". That change raised the
minimum address at which protocol drivers and user programs can register
for request reception from 0x0001'0000'0000 to 0x8000'0000'0000.
It turned out that at least one vendor-specific protocol exists which
uses lower addresses: https://bugzilla.kernel.org/show_bug.cgi?id=76921
For the time being, revert most of commit fcd46b34425d so that affected
protocols work like with kernel v3.13 and before. Just keep the valid
documentation parts from the regressing commit, and the ability to
identify controllers which could be programmed to accept >32 bit
physical DMA addresses. The rest of fcd46b34425d should probably be
brought back as an optional instead of default feature.
Al Viro [Wed, 28 May 2014 17:59:13 +0000 (13:59 -0400)]
expand dentry_kill(dentry, 0) in shrink_dentry_list()
Result will be massaged to saner shape in the next commits. It is
ugly, no questions - the point of that one is to be a provably
equivalent transformation (and it might be worth splitting a bit
more).
Will Deacon [Tue, 27 May 2014 18:11:58 +0000 (19:11 +0100)]
arm64: mm: fix pmd_write CoW brokenness
Commit 9c7e535fcc17 ("arm64: mm: Route pmd thp functions through pte
equivalents") changed the pmd manipulator and accessor functions to
convert the target pmd to a pte, process it with the pte functions, then
convert it back. Along the way, we gained support for PTE_WRITE, however
this is completely ignored by set_pmd_at, and so we fail to set the
PMD_SECT_RDONLY for PMDs, resulting in all sorts of lovely failures (like
CoW not working).
Partially reverting the offending commit (by making use of
PMD_SECT_RDONLY explicitly for pmd_{write,wrprotect,mkwrite} functions)
leads to further issues because pmd_write can then return potentially
incorrect values for page table entries marked as RDONLY, leading to
BUG_ON(pmd_write(entry)) tripping under some THP workloads.
This patch fixes the issue by routing set_pmd_at through set_pte_at,
which correctly takes the PTE_WRITE flag into account. Given that
THP mappings are always anonymous, the additional cache-flushing code
in __sync_icache_dcache won't impose any significant overhead as the
flush will be skipped.
Bjorn Helgaas [Wed, 28 May 2014 22:21:25 +0000 (16:21 -0600)]
Merge branch 'pci/misc' into next
* pci/misc:
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: Turn pcibios_penalize_isa_irq() into a weak function
PCI: Test for std config alias when testing extended config space
Bjorn Helgaas [Wed, 28 May 2014 22:21:07 +0000 (16:21 -0600)]
Merge branches 'pci/hotplug', 'pci/pci_is_bridge' and 'pci/virtualization' into next
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
* pci/host-rcar:
PCI: rcar: Add gen2 device tree support
PCI: rcar: Add R-Car PCIe device tree bindings
PCI: rcar: Add MSI support for PCIe
PCI: rcar: Add Renesas R-Car PCIe driver
PCI: rcar: Use new OF interrupt mapping when possible
* pci/amd-numa:
x86/PCI: Clean up and mark early_root_info_init() as deprecated
x86/PCI: Work around AMD Fam15h BIOSes that fail to provide _PXM
x86/PCI: Warn if we have to "guess" host bridge node information
Alex Williamson [Tue, 20 May 2014 14:53:21 +0000 (08:53 -0600)]
PCI: Introduce new device binding path using pci_dev.driver_override
The driver_override field allows us to specify the driver for a device
rather than relying on the driver to provide a positive match of the
device. This shortcuts the existing process of looking up the vendor and
device ID, adding them to the driver new_id, binding the device, then
removing the ID, but it also provides a couple advantages.
First, the above existing process allows the driver to bind to any device
matching the new_id for the window where it's enabled. This is often not
desired, such as the case of trying to bind a single device to a meta
driver like pci-stub or vfio-pci. Using driver_override we can do this
deterministically using:
Previously we could not invoke drivers_probe after adding a device to
new_id for a driver as we get non-deterministic behavior whether the driver
we intend or the standard driver will claim the device. Now it becomes a
deterministic process, only the driver matching driver_override will probe
the device.
To return the device to the standard driver, we simply clear the
driver_override and reprobe the device:
Another advantage to this approach is that we can specify a driver override
to force a specific binding or prevent any binding. For instance when an
IOMMU group is exposed to userspace through VFIO we require that all
devices within that group are owned by VFIO. However, devices can be
hot-added into an IOMMU group, in which case we want to prevent the device
from binding to any driver (override driver = "none") or perhaps have it
automatically bind to vfio-pci. With driver_override it's a simple matter
for this field to be set internally when the device is first discovered to
prevent driver matches.
Linus Torvalds [Wed, 28 May 2014 18:17:41 +0000 (11:17 -0700)]
Merge tag 'sound-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just two small stable fixes: an HD-audio fix for the new Intel
chipsets and a PM handling fix in PCM dmaengine core"
* tag 'sound-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix onboard audio on Intel H97/Z97 chipsets
ALSA: pcm_dmaengine: Add check during device suspend
Linus Torvalds [Wed, 28 May 2014 18:15:57 +0000 (11:15 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fix from Al Viro:
"Oh, well... Still nothing useful on that livelock (I had something
that looked kinda-sorta like a non-invasive solution, but it
deadlocks), so it's just Miklos' vmsplice fix for now"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: fix vmplice_to_user()
Jens Axboe [Wed, 28 May 2014 16:15:41 +0000 (10:15 -0600)]
blk-mq: add file comments and update copyright notices
None of the blk-mq files have an explanatory comment at the top
for what that particular file does. Add that and add appropriate
copyright notices as well.
The current logic for blocking tag allocation is rather confusing, as we
first allocated and then free again a tag in blk_mq_wait_for_tags, just
to attempt a non-blocking allocation and then repeat if someone else
managed to grab the tag before us.
Instead change blk_mq_alloc_request_pinned to simply do a blocking tag
allocation itself and use the request we get back from it.
Nicolas Pitre [Fri, 23 May 2014 21:31:44 +0000 (22:31 +0100)]
ARM: 8063/1: bL_switcher: fix individual online status reporting of removed CPUs
The content of /sys/devices/system/cpu/cpu*/online is still 1 for those
CPUs that the switcher has removed even though the global state in
/sys/devices/system/cpu/online is updated correctly.
It turns out that commit 0902a9044f ("Driver core: Use generic
offline/online for CPU offline/online") has changed the way those files
retrieve their content by relying on on the generic attribute handling
code. The switcher, by calling cpu_down() directly, bypasses this
handling and the attribute value doesn't get updated.
Fix this by calling device_offline()/device_online() instead.
Thomas Gleixner [Thu, 22 May 2014 03:25:39 +0000 (03:25 +0000)]
rtmutex: Fix deadlock detector for real
The current deadlock detection logic does not work reliably due to the
following early exit path:
/*
* Drop out, when the task has no waiters. Note,
* top_waiter can be NULL, when we are in the deboosting
* mode!
*/
if (top_waiter && (!task_has_pi_waiters(task) ||
top_waiter != task_top_pi_waiter(task)))
goto out_unlock_pi;
So this not only exits when the task has no waiters, it also exits
unconditionally when the current waiter is not the top priority waiter
of the task.
So in a nested locking scenario, it might abort the lock chain walk
and therefor miss a potential deadlock.
Simple fix: Continue the chain walk, when deadlock detection is
enabled.
We also avoid the whole enqueue, if we detect the deadlock right away
(A-A). It's an optimization, but also prevents that another waiter who
comes in after the detection and before the task has undone the damage
observes the situation and detects the deadlock and returns
-EDEADLOCK, which is wrong as the other task is not in a deadlock
situation.
Linus Torvalds [Wed, 28 May 2014 15:08:03 +0000 (08:08 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Small fixes for x86, slightly larger fixes for PPC, and a forgotten
s390 patch. The PPC fixes are important because they fix breakage
that is new in 3.15"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: announce irqfd capability
KVM: x86: disable master clock if TSC is reset during suspend
KVM: vmx: disable APIC virtualization in nested guests
KVM guest: Make pv trampoline code executable
KVM: PPC: Book3S: ifdef on CONFIG_KVM_BOOK3S_32_HANDLER for 32bit
KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit
KVM: PPC: Book3S: HV: make _PAGE_NUMA take effect
Linus Torvalds [Wed, 28 May 2014 15:06:50 +0000 (08:06 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull two powerpc fixes from Ben Herrenschmidt:
"Here's a pair of powerpc fixes for 3.15 which are also going to
stable.
One's a fix for building with newer binutils (the problem currently
only affects the BookE kernels but the affected macro might come back
into use on BookS platforms at any time). Unfortunately, the binutils
maintainer did a backward incompatible change to a construct that we
use so we have to add Makefile check.
The other one is a fix for CPUs getting stuck in kexec when running
single threaded. Since we routinely use kexec on power (including in
our newer bootloaders), I deemed that important enough"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc, kexec: Fix "Processor X is stuck" issue during kexec from ST mode
powerpc: Fix 64 bit builds with binutils 2.24
blk-mq: add helper to insert requests from irq context
Both the cache flush state machine and the SCSI midlayer want to submit
requests from irq context, and the current per-request requeue_work
unfortunately causes corruption due to sharing with the csd field for
flushes. Replace them with a per-request_queue list of requests to
be requeued.
Al Viro [Wed, 28 May 2014 13:48:44 +0000 (09:48 -0400)]
lift the "already marked killed" case into shrink_dentry_list()
It can happen only when dentry_kill() is called with unlock_on_failure
equal to 0 - other callers had dentry pinned until the moment they've
got ->d_lock and DCACHE_DENTRY_KILLED is set only after lockref_mark_dead().
IOW, only one of three call sites of dentry_kill() might end up reaching
that code. Just move it there.
Alex Smith [Thu, 1 May 2014 11:51:19 +0000 (12:51 +0100)]
MIPS: ptrace: Avoid smp_processor_id() in preemptible code
ptrace_{get,set}_watch_regs access current_cpu_data to get the watch
register count/masks, which calls smp_processor_id(). However they are
run in preemptible context and therefore trigger warnings like so:
[ 6340.092000] BUG: using smp_processor_id() in preemptible [00000000] code: gdb/367
[ 6340.092000] caller is ptrace_get_watch_regs+0x44/0x220
Since the watch register count/masks should be the same across all
CPUs, use boot_cpu_data instead. Note that this may need to change in
future should a heterogenous system be supported where the count/masks
are not the same across all CPUs (the current code is also incorrect
for this scenario - current_cpu_data here would not necessarily be
correct for the CPU that the target task will execute on).
The lock is taken in the raw irq path and therefore a rawlock should be
used instead of a normal spinlock.
While here I drop the export symbol on that variable since there are no
other users.
Andreas Schwab [Thu, 24 Apr 2014 10:24:48 +0000 (12:24 +0200)]
m68k: Increase initial mapping to 8 or 16 MiB if possible
If the size of the first memory chunk is at least 8 or 16 MiB increase the
initial mapping to 8 resp. 16 MiB instead of 4 MiB.
This makes it possible to
1. Map more memory in the first node without running out of space for the
page tables,
2. Boot kernels that don't fit in 4 MiB (e.g. multi_defconfig).
Signed-off-by: Andreas Schwab <[email protected]>
- Add support for 8 MiB,
- Store initial mapping size in head.S for later reuse,
- Add comment about large kernels.
Finn Thain [Mon, 26 May 2014 13:29:19 +0000 (23:29 +1000)]
m68k/atari: fix SCC initialization for debug console
Fix SCC initialization for Atari as was previously fixed for Mac. It's
probably not practical to share more code but some attempt is made to
align the Mac and Atari variants.
Finn Thain [Sat, 12 Apr 2014 13:49:30 +0000 (23:49 +1000)]
m68k/mvme16x: Adopt common boot console
In a multi-platform kernel binary we only need one early console instance.
The difficulty here is that the common early console is started by
early_param(), whereas the MVME16x instance is started later by
config_mvme16x(). That means some interrupt setup must be done earlier.
Signed-off-by: Finn Thain <[email protected]> Tested-by: Stephen N Chivers <[email protected]>
[Geert] Tag debug_cons_write() with __ref to kill section mismatch warning Signed-off-by: Geert Uytterhoeven <[email protected]>
Finn Thain [Sat, 12 Apr 2014 13:48:56 +0000 (23:48 +1000)]
m68k: Multi-platform EARLY_PRINTK
Make the boot console available to more m68k platforms by leveraging
the head.S debug console.
The boot console is enabled by the "earlyprintk" command line argument
which is how most other architectures do this.
This is a change of behaviour for the Mac but does not negatively impact
the common use-case which is not debugging.
This is also a change of behaviour for other platforms because it means
the serial port stays quiet when CONFIG_EARLY_PRINTK is not enabled. This
is also an improvement for the common use-case.
Linus Walleij [Wed, 28 May 2014 07:14:06 +0000 (09:14 +0200)]
gpio: mcp23s08: switch chip count to int
Commit 3e3bed913e8bbd78f38cefd5d575475f45c05dd0
"gpio: mcp23s08: fixed count variable for devicetree probing"
introduced a loop check to see if the number of chips were
unconsistent and going below zero counting downwards, but
this requires the counting variable to be able to be
negative, so switch the variable from unsigned to int.
projects / linux.git / log