- eth: bnxt_en: fix the double free during device removal
- tools: ynl:
- fix enum-as-flags in the generic CLI
- fully inherit attrs in subsets
- re-license uniformly under GPL-2.0 or BSD-3-clause
Previous releases - regressions:
- core: use indirect calls helpers for sk_exit_memory_pressure()
- tls:
- fix return value for async crypto
- avoid hanging tasks on the tx_lock
- eth: ice: copy last block omitted in ice_get_module_eeprom()
Previous releases - always broken:
- core: avoid double iput when sock_alloc_file fails
- af_unix: fix struct pid leaks in OOB support
- tls:
- fix possible race condition
- fix device-offloaded sendpage straddling records
- bpf:
- sockmap: fix an infinite loop error
- test_run: fix &xdp_frame misplacement for LIVE_FRAMES
- fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
- netfilter: tproxy: fix deadlock due to missing BH disable
- phylib: get rid of unnecessary locking
- eth: bgmac: fix *initial* chip reset to support BCM5358
- eth: nfp: fix csum for ipsec offload
- eth: mtk_eth_soc: fix RX data corruption issue
Misc:
- usb: qmi_wwan: add telit 0x1080 composition"
* tag 'net-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (64 commits)
tools: ynl: fix enum-as-flags in the generic CLI
tools: ynl: move the enum classes to shared code
net: avoid double iput when sock_alloc_file fails
af_unix: fix struct pid leaks in OOB support
eth: fealnx: bring back this old driver
net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
net: microchip: sparx5: fix deletion of existing DSCP mappings
octeontx2-af: Unlock contexts in the queue context cache in case of fault detection
net/smc: fix fallback failed while sendmsg with fastopen
ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause
mailmap: update entries for Stephen Hemminger
mailmap: add entry for Maxim Mikityanskiy
nfc: change order inside nfc_se_io error path
ethernet: ice: avoid gcc-9 integer overflow warning
ice: don't ignore return codes in VSI related code
ice: Fix DSCP PFC TLV creation
net: usb: qmi_wwan: add Telit 0x1080 composition
net: usb: cdc_mbim: avoid altsetting toggling for Telit FE990
netfilter: conntrack: adopt safer max chain length
net: tls: fix device-offloaded sendpage straddling records
...
Linus Torvalds [Thu, 9 Mar 2023 18:17:23 +0000 (10:17 -0800)]
Merge tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential out of bound write of zeroes in HID core with a
specially crafted uhid device (Lee Jones)
- fix potential use-after-free in work function in intel-ish-hid (Reka
Norman)
- selftests config fixes (Benjamin Tissoires)
- few device small fixes and support
* tag 'for-linus-2023030901' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: ipc: Fix potential use-after-free in work function
HID: logitech-hidpp: Add support for Logitech MX Master 3S mouse
HID: cp2112: Fix driver not registering GPIO IRQ chip as threaded
selftest: hid: fix hid_bpf not set in config
HID: uhid: Over-ride the default maximum data buffer value with our own
HID: core: Provide new max_buffer_size attribute to over-ride the default
Linus Torvalds [Thu, 9 Mar 2023 18:08:46 +0000 (10:08 -0800)]
Merge tag 'm68k-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- Fix systems with memory at end of 32-bit address space
- Fix initrd on systems where memory does not start at address zero
- Fix 68030 handling of bus errors for addresses in exception tables
* tag 'm68k-for-v6.3-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Only force 030 bus error if PC not in exception table
m68k: mm: Move initrd phys_to_virt handling after paging_init()
m68k: mm: Fix systems with memory at end of 32-bit address space
Al Viro [Mon, 6 Mar 2023 01:20:30 +0000 (01:20 +0000)]
sh: sanitize the flags on sigreturn
We fetch %SR value from sigframe; it might have been modified by signal
handler, so we can't trust it with any bits that are not modifiable in
user mode.
Jens Axboe [Thu, 9 Mar 2023 16:51:13 +0000 (09:51 -0700)]
io_uring: silence variable ‘prev’ set but not used warning
If io_uring.o is built with W=1, it triggers a warning:
io_uring/io_uring.c: In function ‘__io_submit_flush_completions’:
io_uring/io_uring.c:1502:40: warning: variable ‘prev’ set but not used [-Wunused-but-set-variable]
1502 | struct io_wq_work_node *node, *prev;
| ^~~~
which is due to the wq_list_for_each() iterator always keeping a 'prev'
variable. Most users need this to remove an entry from a list, for
example, but __io_submit_flush_completions() never does that.
Add a basic helper that doesn't track prev instead, and use that in
that function.
Jens Axboe [Wed, 8 Mar 2023 16:26:13 +0000 (09:26 -0700)]
io_uring/uring_cmd: ensure that device supports IOPOLL
It's possible for a file type to support uring commands, but not
pollable ones. Hence before issuing one of those, we should check
that it is supported and error out upfront if it isn't.
Gao Xiang [Thu, 9 Mar 2023 05:31:47 +0000 (13:31 +0800)]
erofs: Revert "erofs: fix kvcalloc() misuse with __GFP_NOFAIL"
Let's revert commit 12724ba38992 ("erofs: fix kvcalloc() misuse with
__GFP_NOFAIL") since kvmalloc() already supports __GFP_NOFAIL in commit a421ef303008 ("mm: allow !GFP_KERNEL allocations for kvmalloc"). So
the original fix was wrong.
Actually there was some issue as [1] discussed, so before that mm fix
is landed, the warn could still happen but applying this commit first
will cause less.
Now that the same hardware that the r8188eu driver supported is
supported by the real wireless driver rtl8xxxu, the r8188eu driver can
be deleted.
Also the rtl8xxxu driver supports way more devices, and is a fraction of
the overall size, making this a much better overall solution.
Thanks to the r8188eu developers and maintainers and reviewers over the
years, your work allowed Linux users to use their hardware before the
real driver was implemented properly.
====================
tools: ynl: fix enum-as-flags in the generic CLI
The CLI needs to use proper classes when looking at Enum definitions
rather than interpreting the YAML spec ad-hoc, because we have more
than on format of the definition supported.
====================
Jakub Kicinski [Wed, 8 Mar 2023 00:39:23 +0000 (16:39 -0800)]
tools: ynl: fix enum-as-flags in the generic CLI
Lorenzo points out that the generic CLI is broken for the netdev
family. When I added the support for documentation of enums
(and sparse enums) the client script was not updated.
It expects the values in enum to be a list of names,
now it can also be a dict (YAML object).
Reported-by: Lorenzo Bianconi <[email protected]> Fixes: e4b48ed460d3 ("tools: ynl: add a completely generic client") Signed-off-by: Jakub Kicinski <[email protected]>
When sock_alloc_file fails to allocate a file, it will call sock_release.
__sys_socket_file should then not call sock_release again, otherwise there
will be a double free.
Vladimir Oltean [Tue, 7 Mar 2023 15:54:11 +0000 (17:54 +0200)]
net: dsa: mt7530: permit port 5 to work without port 6 on MT7621 SoC
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe359 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a80560 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909db ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Linus Torvalds [Wed, 8 Mar 2023 20:02:09 +0000 (12:02 -0800)]
Merge tag 'fs_for_v6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull udf fixes from Jan Kara:
"Fix bugs in UDF caused by the big pile of changes that went in during
the merge window"
* tag 'fs_for_v6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Warn if block mapping is done for in-ICB files
udf: Fix reading of in-ICB files
udf: Fix lost writes in udf_adinicb_writepage()
Linus Torvalds [Wed, 8 Mar 2023 19:56:45 +0000 (11:56 -0800)]
Merge tag 'platform-drivers-x86-v6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A small set of assorted bug and build/warning fixes"
* tag 'platform-drivers-x86-v6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform: mellanox: mlx-platform: Initialize shift variable to 0
platform/x86: int3472: Add GPIOs to Surface Go 3 Board data
platform/x86: ISST: Fix kernel documentation warnings
platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
platform: mellanox: select REGMAP instead of depending on it
platform/x86/intel/tpmi: Fix double free reported by Smatch
platform/x86: ISST: Increase range of valid mail box commands
platform/x86: dell-ddv: Fix temperature scaling
platform/x86: dell-ddv: Fix cache invalidation on resume
platform/x86/amd: pmc: remove CONFIG_SUSPEND checks
Randy Dunlap [Mon, 20 Feb 2023 01:04:28 +0000 (17:04 -0800)]
drm/msm: DEVFREQ_GOV_SIMPLE_ONDEMAND is no longer needed
DRM_MSM no longer needs DEVFREQ_GOV_SIMPLE_ONDEMAND (since commit dbd7a2a941b8 ("PM / devfreq: Fix build issues with devfreq disabled")
in linux-next), so remove that select from the DRM_MSM Kconfig file.
Linus Torvalds [Tue, 7 Mar 2023 21:06:29 +0000 (13:06 -0800)]
x86/resctl: fix scheduler confusion with 'current'
The implementation of 'current' on x86 is very intentionally special: it
is a very common thing to look up, and it uses 'this_cpu_read_stable()'
to get the current thread pointer efficiently from per-cpu storage.
And the keyword in there is 'stable': the current thread pointer never
changes as far as a single thread is concerned. Even if when a thread
is preempted, or moved to another CPU, or even across an explicit call
'schedule()' that thread will still have the same value for 'current'.
It is, after all, the kernel base pointer to thread-local storage.
That's why it's stable to begin with, but it's also why it's important
enough that we have that special 'this_cpu_read_stable()' access for it.
So this is all done very intentionally to allow the compiler to treat
'current' as a value that never visibly changes, so that the compiler
can do CSE and combine multiple different 'current' accesses into one.
However, there is obviously one very special situation when the
currently running thread does actually change: inside the scheduler
itself.
So the scheduler code paths are special, and do not have a 'current'
thread at all. Instead there are _two_ threads: the previous and the
next thread - typically called 'prev' and 'next' (or prev_p/next_p)
internally.
So this is all actually quite straightforward and simple, and not all
that complicated.
Except for when you then have special code that is run in scheduler
context, that code then has to be aware that 'current' isn't really a
valid thing. Did you mean 'prev'? Did you mean 'next'?
In fact, even if then look at the code, and you use 'current' after the
new value has been assigned to the percpu variable, we have explicitly
told the compiler that 'current' is magical and always stable. So the
compiler is quite free to use an older (or newer) value of 'current',
and the actual assignment to the percpu storage is not relevant even if
it might look that way.
Which is exactly what happened in the resctl code, that blithely used
'current' in '__resctrl_sched_in()' when it really wanted the new
process state (as implied by the name: we're scheduling 'into' that new
resctl state). And clang would end up just using the old thread pointer
value at least in some configurations.
This could have happened with gcc too, and purely depends on random
compiler details. Clang just seems to have been more aggressive about
moving the read of the per-cpu current_task pointer around.
The fix is trivial: just make the resctl code adhere to the scheduler
rules of using the prev/next thread pointer explicitly, instead of using
'current' in a situation where it just wasn't valid.
That same code is then also used outside of the scheduler context (when
a thread resctl state is explicitly changed), and then we will just pass
in 'current' as that pointer, of course. There is no ambiguity in that
case.
The fix may be trivial, but noticing and figuring out what went wrong
was not. The credit for that goes to Stephane Eranian.
Hans de Goede [Mon, 6 Mar 2023 15:35:12 +0000 (16:35 +0100)]
staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
To last 2 parameters to cfg80211_get_bss() should be of
the enum ieee80211_bss_type resp. enum ieee80211_privacy types,
which WLAN_CAPABILITY_ESS very much is not.
Fix both cfg80211_get_bss() calls in ioctl_cfg80211.c to pass
the right parameters.
Note that the second call was already somewhat fixed by commenting
out WLAN_CAPABILITY_ESS and passing in 0 instead. This was still
not entirely correct though since that would limit returned
BSS-es to ESS type BSS-es with privacy on.
Hans de Goede [Mon, 6 Mar 2023 15:35:11 +0000 (16:35 +0100)]
staging: rtl8723bs: Fix key-store index handling
There are 2 issues with the key-store index handling
1. The non WEP key stores can store keys with indexes 0 - BIP_MAX_KEYID,
this means that they should be an array with BIP_MAX_KEYID + 1
entries. But some of the arrays where just BIP_MAX_KEYID entries
big. While one other array was hardcoded to a size of 6 entries,
instead of using the BIP_MAX_KEYID define.
2. The rtw_cfg80211_set_encryption() and wpa_set_encryption() functions
index check where checking that the passed in key-index would fit
inside both the WEP key store (which only has 4 entries) as well as
in the non WEP key stores. This breaks any attempts to set non WEP
keys with index 4 or 5.
Issue 2. specifically breaks wifi connection with some access points
which advertise PMF support. Without this fix connecting to these
access points fails with the following wpa_supplicant messages:
nl80211: kernel reports: key addition failed
wlan0: WPA: Failed to configure IGTK to the driver
wlan0: RSN: Failed to configure IGTK
wlan0: CTRL-EVENT-DISCONNECTED bssid=... reason=1 locally_generated=1
Fix 1. by using the right size for the key-stores. After this 2. can
safely be fixed by checking the right max-index value depending on the
used algorithm, fixing wifi not working with some PMF capable APs.
Remove call_usermodehelper starting /etc/acpi/events/RadioPower.sh that
is not available. This script is not part of the kernel and it is not
officially available on the www. The result is that this lines are just
dead code.
Philipp Hortmann [Tue, 28 Feb 2023 20:28:57 +0000 (21:28 +0100)]
staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
Remove function _rtl92e_dm_check_ac_dc_power calling a script
/etc/acpi/wireless-rtl-ac-dc-power.sh that is not available. This script
is not part of the kernel and it is not available on the www. The result
is that this function is just dead code.
Jens Axboe [Wed, 8 Mar 2023 14:18:51 +0000 (07:18 -0700)]
io_uring/io-wq: stop setting PF_NO_SETAFFINITY on io-wq workers
Every now and then reports come in that are puzzled on why changing
affinity on the io-wq workers fails with EINVAL. This happens because they
set PF_NO_SETAFFINITY as part of their creation, as io-wq organizes
workers into groups based on what CPU they are running on.
However, this is purely an optimization and not a functional requirement.
We can allow setting affinity, and just lazily update our worker to wqe
mappings. If a given io-wq thread times out, it normally exits if there's
no more work to do. The exception is if it's the last worker available.
For the timeout case, check the affinity of the worker against group mask
and exit even if it's the last worker. New workers should be created with
the right mask and in the right location.
Yu Kuai [Wed, 8 Mar 2023 02:32:08 +0000 (10:32 +0800)]
block, bfq: fix uaf for 'stable_merge_bfqq'
Before commit fd571df0ac5b ("block, bfq: turn bfqq_data into an array
in bfq_io_cq"), process reference is read before bfq_put_stable_ref(),
and it's safe if bfq_put_stable_ref() put the last reference, because
process reference will be 0 and 'stable_merge_bfqq' won't be accessed
in this case. However, the commit changed the order and will cause
uaf for 'stable_merge_bfqq'.
In order to emphasize that bfq_put_stable_ref() can drop the last
reference, fix the problem by moving bfq_put_stable_ref() to the end of
bfq_setup_stable_merge().
Daniel Machon [Tue, 7 Mar 2023 11:21:03 +0000 (12:21 +0100)]
net: microchip: sparx5: fix deletion of existing DSCP mappings
Fix deletion of existing DSCP mappings in the APP table.
Adding and deleting DSCP entries are replicated per-port, since the
mapping table is global for all ports in the chip. Whenever a mapping
for a DSCP value already exists, the old mapping is deleted first.
However, it is only deleted for the specified port. Fix this by calling
sparx5_dcb_ieee_delapp() instead of dcb_ieee_delapp() as it ought to be.
Reproduce:
// Map and remap DSCP value 63
$ dcb app add dev eth0 dscp-prio 63:1
$ dcb app add dev eth0 dscp-prio 63:2
$ dcb app show dev eth0 dscp-prio
dscp-prio 63:2
$ dcb app show dev eth1 dscp-prio
dscp-prio 63:1 63:2 <-- 63:1 should not be there
Fixes: 8dcf69a64118 ("net: microchip: sparx5: add support for offloading dscp table") Signed-off-by: Daniel Machon <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Suman Ghosh [Tue, 7 Mar 2023 10:49:08 +0000 (16:19 +0530)]
octeontx2-af: Unlock contexts in the queue context cache in case of fault detection
NDC caches contexts of frequently used queue's (Rx and Tx queues)
contexts. Due to a HW errata when NDC detects fault/poision while
accessing contexts it could go into an illegal state where a cache
line could get locked forever. To makesure all cache lines in NDC
are available for optimum performance upon fault/lockerror/posion
errors scan through all cache lines in NDC and clear the lock bit.
D. Wythe [Tue, 7 Mar 2023 03:23:46 +0000 (11:23 +0800)]
net/smc: fix fallback failed while sendmsg with fastopen
Before determining whether the msg has unsupported options, it has been
prematurely terminated by the wrong status check.
For the application, the general usages of MSG_FASTOPEN likes
fd = socket(...)
/* rather than connect */
sendto(fd, data, len, MSG_FASTOPEN)
Hence, We need to check the flag before state check, because the sock
state here is always SMC_INIT when applications tries MSG_FASTOPEN.
Once we found unsupported options, fallback it to TCP.
Fixes: ee9dfbef02d1 ("net/smc: handle sockopts forcing fallback") Signed-off-by: D. Wythe <[email protected]> Signed-off-by: Simon Horman <[email protected]>
v2 -> v1: Optimize code style Reviewed-by: Tony Lu <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Tobias Klauser [Wed, 8 Mar 2023 10:51:26 +0000 (11:51 +0100)]
fork: allow CLONE_NEWTIME in clone3 flags
Currently, calling clone3() with CLONE_NEWTIME in clone_args->flags
fails with -EINVAL. This is because CLONE_NEWTIME intersects with
CSIGNAL. However, CSIGNAL was deprecated when clone3 was introduced in
commit 7f192e3cd316 ("fork: add clone3"), allowing re-use of that part
of clone flags.
Fix this by explicitly allowing CLONE_NEWTIME in clone3_args_valid. This
is also in line with the respective check in check_unshare_flags which
allow CLONE_NEWTIME for unshare().
The watch_queue_set_size() allocation error paths return the ret value
set via the prior pipe_resize_ring() call, which will always be zero.
As a result, IOC_WATCH_QUEUE_SET_SIZE callers such as "keyctl watch"
fail to detect kernel wqueue->notes allocation failures and proceed to
KEYCTL_WATCH_KEY, with any notifications subsequently lost.
Fixes: c73be61cede58 ("pipe: Add general notification queue support") Signed-off-by: David Disseldorp <[email protected]> Signed-off-by: Christian Brauner (Microsoft) <[email protected]>
Jan Kara [Wed, 1 Mar 2023 14:10:04 +0000 (15:10 +0100)]
ext4: Fix deadlock during directory rename
As lockdep properly warns, we should not be locking i_rwsem while having
transactions started as the proper lock ordering used by all directory
handling operations is i_rwsem -> transaction start. Fix the lock
ordering by moving the locking of the directory earlier in
ext4_rename().
Wu Bo [Wed, 22 Feb 2023 01:35:24 +0000 (09:35 +0800)]
docs: ext4: modify the group desc size to 64
Since the default ext4 group desc size is 64 now (assuming that the
64-bit feature is enbled). And the size mentioned in this doc is 64 too.
Change it to 64.
For GETFSMAP calls, the caller selects a physical block device by
writing its block number into fsmap_head.fmh_keys[01].fmr_device.
To query mappings for a subrange of the device, the starting byte of the
range is written to fsmap_head.fmh_keys[0].fmr_physical and the last
byte of the range goes in fsmap_head.fmh_keys[1].fmr_physical.
IOWs, to query what mappings overlap with bytes 3-14 of /dev/sda, you'd
set the inputs as follows:
Which would return you whatever is mapped in the 12 bytes starting at
physical offset 3.
The crash is due to insufficient range validation of keys[1] in
ext4_getfsmap_datadev. On 1k-block filesystems, block 0 is not part of
the filesystem, which means that s_first_data_block is nonzero.
ext4_get_group_no_and_offset subtracts this quantity from the blocknr
argument before cracking it into a group number and a block number
within a group. IOWs, block group 0 spans blocks 1-8192 (1-based)
instead of 0-8191 (0-based) like what happens with larger blocksizes.
The net result of this encoding is that blocknr < s_first_data_block is
not a valid input to this function. The end_fsb variable is set from
the keys that are copied from userspace, which means that in the above
example, its value is zero. That leads to an underflow here:
Leaving an impossibly large group number (2^32-1) in blocknr.
ext4_getfsmap_check_keys checked that keys[0].fmr_physical and
keys[1].fmr_physical are in increasing order, but
ext4_getfsmap_datadev adjusts keys[0].fmr_physical to be at least
s_first_data_block. This implies that we have to check it again after
the adjustment, which is the piece that I forgot.
Eric Whitney [Fri, 10 Feb 2023 17:32:44 +0000 (12:32 -0500)]
ext4: fix RENAME_WHITEOUT handling for inline directories
A significant number of xfstests can cause ext4 to log one or more
warning messages when they are run on a test file system where the
inline_data feature has been enabled. An example:
"EXT4-fs warning (device vdc): ext4_dirblock_csum_set:425: inode
#16385: comm fsstress: No space for directory leaf checksum. Please
run e2fsck -D."
The xfstests include: ext4/057, 058, and 307; generic/013, 051, 068,
070, 076, 078, 083, 232, 269, 270, 390, 461, 475, 476, 482, 579, 585,
589, 626, 631, and 650.
In this situation, the warning message indicates a bug in the code that
performs the RENAME_WHITEOUT operation on a directory entry that has
been stored inline. It doesn't detect that the directory is stored
inline, and incorrectly attempts to compute a dirent block checksum on
the whiteout inode when creating it. This attempt fails as a result
of the integrity checking in get_dirent_tail (usually due to a failure
to match the EXT4_FT_DIR_CSUM magic cookie), and the warning message
is then emitted.
Fix this by simply collecting the inlined data state at the time the
search for the source directory entry is performed. Existing code
handles the rest, and this is sufficient to eliminate all spurious
warning messages produced by the tests above. Go one step further
and do the same in the code that resets the source directory entry in
the event of failure. The inlined state should be present in the
"old" struct, but given the possibility of a race there's no harm
in taking a conservative approach and getting that information again
since the directory entry is being reread anyway.
Eric Biggers [Fri, 3 Feb 2023 00:55:03 +0000 (16:55 -0800)]
ext4: fix cgroup writeback accounting with fs-layer encryption
When writing a page from an encrypted file that is using
filesystem-layer encryption (not inline encryption), ext4 encrypts the
pagecache page into a bounce page, then writes the bounce page.
It also passes the bounce page to wbc_account_cgroup_owner(). That's
incorrect, because the bounce page is a newly allocated temporary page
that doesn't have the memory cgroup of the original pagecache page.
This makes wbc_account_cgroup_owner() not account the I/O to the owner
of the pagecache page as it should.
Fix this by always passing the pagecache page to
wbc_account_cgroup_owner().
Filipe Manana [Mon, 6 Mar 2023 10:13:34 +0000 (10:13 +0000)]
btrfs: fix block group item corruption after inserting new block group
We can often end up inserting a block group item, for a new block group,
with a wrong value for the used bytes field.
This happens if for the new allocated block group, in the same transaction
that created the block group, we have tasks allocating extents from it as
well as tasks removing extents from it.
For example:
1) Task A creates a metadata block group X;
2) Two extents are allocated from block group X, so its "used" field is
updated to 32K, and its "commit_used" field remains as 0;
3) Transaction commit starts, by some task B, and it enters
btrfs_start_dirty_block_groups(). There it tries to update the block
group item for block group X, which currently has its "used" field with
a value of 32K. But that fails since the block group item was not yet
inserted, and so on failure update_block_group_item() sets the
"commit_used" field of the block group back to 0;
4) The block group item is inserted by task A, when for example
btrfs_create_pending_block_groups() is called when releasing its
transaction handle. This results in insert_block_group_item() inserting
the block group item in the extent tree (or block group tree), with a
"used" field having a value of 32K, but without updating the
"commit_used" field in the block group, which remains with value of 0;
5) The two extents are freed from block X, so its "used" field changes
from 32K to 0;
6) The transaction commit by task B continues, it enters
btrfs_write_dirty_block_groups() which calls update_block_group_item()
for block group X, and there it decides to skip the block group item
update, because "used" has a value of 0 and "commit_used" has a value
of 0 too.
As a result, we end up with a block item having a 32K "used" field but
no extents allocated from it.
When this issue happens, a btrfs check reports an error like this:
[1/7] checking root items
[2/7] checking extents
block group [11041505281073741824] used 39796736 but extent items used 0
ERROR: errors found in extent allocation tree or chunk allocation
(...)
Fix this by making insert_block_group_item() update the block group's
"commit_used" field.
Jakub Kicinski [Mon, 6 Mar 2023 20:04:57 +0000 (12:04 -0800)]
ynl: re-license uniformly under GPL-2.0 OR BSD-3-Clause
I was intending to make all the Netlink Spec code BSD-3-Clause
to ease the adoption but it appears that:
- I fumbled the uAPI and used "GPL WITH uAPI note" there
- it gives people pause as they expect GPL in the kernel
As suggested by Chuck re-license under dual. This gives us benefit
of full BSD freedom while fulfilling the broad "kernel is under GPL"
expectations.
Fedor Pchelkin [Mon, 6 Mar 2023 21:26:50 +0000 (00:26 +0300)]
nfc: change order inside nfc_se_io error path
cb_context should be freed on the error path in nfc_se_io as stated by
commit 25ff6f8a5a3b ("nfc: fix memory leak of se_io context in
nfc_genl_se_io").
Make the error path in nfc_se_io unwind everything in reverse order, i.e.
free the cb_context after unlocking the device.
ice: don't ignore return codes in VSI related code
There were few smatch warnings reported by Dan:
- ice_vsi_cfg_xdp_txqs can return 0 instead of ret, which is cleaner
- return values in ice_vsi_cfg_def were ignored
- in ice_vsi_rebuild return value was ignored in case rebuild failed,
it was a never reached code, however, rewrite it for clarity.
- ice_vsi_cfg_tc can return 0 instead of ret
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Reported-by: Dan Carpenter <[email protected]> Signed-off-by: Michal Swiatkowski <[email protected]> Tested-by: Gurucharan G <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]>
Dave Ertman [Fri, 27 Jan 2023 13:24:10 +0000 (14:24 +0100)]
ice: Fix DSCP PFC TLV creation
When creating the TLV to send to the FW for configuring DSCP mode PFC,the
PFCENABLE field was being masked with a 4 bit mask (0xF), but this is an 8
bit bitmask for enabled classes for PFC. This means that traffic classes
4-7 could not be enabled for PFC.
Remove the mask completely, as it is not necessary, as we are assigning 8
bits to an 8 bit field.
Swapnil Patel [Wed, 1 Mar 2023 19:33:33 +0000 (14:33 -0500)]
drm/amd/display: Update clock table to include highest clock setting
[Why]
Currently, the clk manager matches SocVoltage with voltage from
fused settings (dfPstate clock table). And then corresponding clocks
are selected.
However in certain situations, this leads to clk manager not
including at least one entry with highest supported clock setting.
[How]
Update the clk manager to include at least one entry with highest
supported clock setting.
Candice Li [Fri, 24 Feb 2023 09:26:33 +0000 (17:26 +0800)]
drm/amdgpu: Support umc node harvest config on umc v8_10
Don't need to query error count and error address on harvest umc nodes.
v2: Fix code bug, use active_mask instead of harvsest_config
and remove unnecessary argument in LOOP macro.
v3: Leave adev->gmc.num_umc unchanged.
Harry Wentland [Fri, 13 Jan 2023 16:24:08 +0000 (11:24 -0500)]
drm/display: Don't block HDR_OUTPUT_METADATA on unknown EOTF
The EDID of an HDR display defines EOTFs that are supported
by the display and can be set in the HDR metadata infoframe.
Userspace is expected to read the EDID and set an appropriate
HDR_OUTPUT_METADATA.
In drm_parse_hdr_metadata_block the kernel reads the supported
EOTFs from the EDID and stores them in the
drm_connector->hdr_sink_metadata. While doing so it also
filters the EOTFs to the EOTFs the kernel knows about.
When an HDR_OUTPUT_METADATA is set it then checks to
make sure the EOTF is a supported EOTF. In cases where
the kernel doesn't know about a new EOTF this check will
fail, even if the EDID advertises support.
Since it is expected that userspace reads the EDID to understand
what the display supports it doesn't make sense for DRM to block
an HDR_OUTPUT_METADATA if it contains an EOTF the kernel doesn't
understand.
This comes with the added benefit of future-proofing metadata
support. If the spec defines a new EOTF there is no need to
update DRM and an compositor can immediately make use of it.
Conor Dooley [Thu, 2 Mar 2023 17:41:55 +0000 (17:41 +0000)]
RISC-V: fix taking the text_mutex twice during sifive errata patching
Chris pointed out that some bonehead, *cough* me *cough*, added two
mutex_locks() to the SiFive errata patching. The second was meant to
have been a mutex_unlock().
Linus Torvalds [Tue, 7 Mar 2023 20:16:18 +0000 (12:16 -0800)]
cpumask: be more careful with 'cpumask_setall()'
Commit 596ff4a09b89 ("cpumask: re-introduce constant-sized cpumask
optimizations") changed cpumask_setall() to use "bitmap_set()" instead
of "bitmap_fill()", because bitmap_fill() would explicitly set all the
bits of a constant sized small bitmap, and that's exactly what we don't
want: we want to only set bits up to 'nr_cpu_ids', which is what
"bitmap_set()" does.
However, Yury correctly points out that while "bitmap_set()" does indeed
only set bits up to the required bitmap size, it doesn't _clear_ bits
above that size, so the upper bits would still not have well-defined
values.
Now, none of this should really matter, since any bits set past
'nr_cpu_ids' should always be ignored in the first place. Yes, the bit
scanning functions might return them as a result, but since users should
always consider the ">= nr_cpu_ids" condition to mean "no more bits",
that shouldn't have any actual effect (see previous commit 8ca09d5fa354
"cpumask: fix incorrect cpumask scanning result checks").
But let's just do it right, the way the code was _intended_ to work. We
have had enough lazy code that works but bites us in the *rse later
(again, see previous commit) that there's no reason to not just do this
properly.
It turns out that "bitmap_fill()" gets this all right for the complex
case, and really only fails for the inlined optimized case that just
fills the whole word. And while we could just fix bitmap_fill() to use
the proper last word mask, there's two issues with that:
- the cpumask case wants to do the _optimization_ based on "NR_CPUS is
a small constant", but then wants to do the actual bit _fill_ based
on "nr_cpu_ids" that isn't necessarily that same constant
- we have lots of non-cpumask users of bitmap_fill(), and while they
hopefully don't care, and probably would want the proper semantics
anyway ("only set bits up to the limit"), I do not want the cpumask
changes to impact other parts
So this ends up just doing the single-word optimization by hand in the
cpumask code. If our cpumask is fundamentally limited to a single word,
just do the proper "fill in that word" exactly. And if it's the more
complex multi-word case, then the generic bitmap_fill() will DTRT.
This is all an example of how our bitmap function optimizations really
are somewhat broken. They conflate the "this is size of the bitmap"
optimizations with the actual bit(s) we want to set.
In many cases we really want to have the two be separate things:
sometimes we base our optimizations on the size of the whole bitmap ("I
know this whole bitmap fits in a single word, so I'll just use
single-word accesses"), and sometimes we base them on the bit we are
looking at ("this is just acting on bits that are in the first word, so
I'll use single-word accesses").
Notice how the end result of the two optimizations are the same, but the
way we get to them are quite different.
And all our cpumask optimization games are really about that fundamental
distinction, and we'd often really want to pass in both the "this is the
bit I'm working on" (which _can_ be a small constant but might be
variable), and "I know it's in this range even if it's variable" (based
on CONFIG_NR_CPUS).
So this cpumask_setall() implementation just makes that explicit. It
checks the "I statically know the size is small" using the known static
size of the cpumask (which is what that 'small_cpumask_bits' is all
about), but then sets the actual bits using the exact number of cpus we
have (ie 'nr_cpumask_bits')
Of course, in a perfect world, the compiler would have done all the
range analysis (possibly with help from us just telling it that
"this value is always in this range"), and would do all of this for us.
But that is not the world we live in.
While we dream of that perfect world, this does that manual logic to
make it all work out. And this was a very long explanation for a small
code change that shouldn't even matter.
Yu Kuai [Tue, 7 Mar 2023 10:55:52 +0000 (18:55 +0800)]
block: fix wrong mode for blkdev_put() from disk_scan_partitions()
If disk_scan_partitions() is called with 'FMODE_EXCL',
blkdev_get_by_dev() will be called without 'FMODE_EXCL', however, follow
blkdev_put() is still called with 'FMODE_EXCL', which will cause
'bd_holders' counter to leak.
Fix the problem by using the right mode for blkdev_put().
Paolo Abeni [Tue, 7 Mar 2023 12:52:03 +0000 (13:52 +0100)]
Merge branch 'main' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Restore ctnetlink zero mark in events and dump, from Ivan Delalande.
2) Fix deadlock due to missing disabled bh in tproxy, from Florian Westphal.
3) Safer maximum chain load in conntrack, from Eric Dumazet.
* 'main' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: conntrack: adopt safer max chain length
netfilter: tproxy: fix deadlock due to missing BH disable
netfilter: ctnetlink: revert to dumping mark regardless of event type
====================
Daniel Scally [Thu, 2 Mar 2023 10:26:11 +0000 (10:26 +0000)]
platform/x86: int3472: Add GPIOs to Surface Go 3 Board data
Add the INT347E GPIO lookup table to the board data for the Surface
Go 3. This is necessary to allow the ov7251 IR camera to probe
properly on that platform.
Randy Dunlap [Sun, 26 Feb 2023 05:39:51 +0000 (21:39 -0800)]
platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Randy Dunlap [Sun, 26 Feb 2023 05:39:50 +0000 (21:39 -0800)]
platform: mellanox: select REGMAP instead of depending on it
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
For NVSW_SN2201, select REGMAP_I2C instead of depending on it.
platform/x86/intel/tpmi: Fix double free reported by Smatch
Fix warning:
drivers/platform/x86/intel/tpmi.c:253 tpmi_create_device()
warn: 'feature_vsec_dev' was already freed.
If there is some error, feature_vsec_dev memory is freed as part
of resource managed call intel_vsec_add_aux(). So, additional
kfree() call is not required.
Reordered res allocation and feature_vsec_dev, so that on error
only res is freed.
platform/x86: ISST: Increase range of valid mail box commands
A new command CONFIG_TDP_GET_RATIO_INFO is added, with sub command type
of 0x0C. The previous range of valid sub commands was from 0x00 to 0x0B.
Change the valid range from 0x00 to 0x0C.
Armin Wolf [Sat, 18 Feb 2023 11:53:18 +0000 (12:53 +0100)]
platform/x86: dell-ddv: Fix temperature scaling
After using the built-in UEFI hardware diagnostics to compare
the measured battery temperature, i noticed that the temperature
is actually expressed in tenth degree kelvin, similar to the
SBS-Data standard. For example, a value of 2992 is displayed as
26 degrees celsius.
Fix the scaling so that the correct values are being displayed.
Armin Wolf [Sat, 18 Feb 2023 11:53:17 +0000 (12:53 +0100)]
platform/x86: dell-ddv: Fix cache invalidation on resume
If one or both sensor buffers could not be initialized, either
due to missing hardware support or due to some error during probing,
the resume handler will encounter undefined behaviour when
attempting to lock buffers then protected by an uninitialized or
destroyed mutex.
Fix this by introducing a "active" flag which is set during probe,
and only invalidate buffers which where flaged as "active".
The amd_pmc_write_stb() function was previously hidden in an
ifdef to avoid a warning when CONFIG_SUSPEND is disabled, but
now there is an additional caller:
drivers/platform/x86/amd/pmc.c: In function 'amd_pmc_stb_debugfs_open_v2':
drivers/platform/x86/amd/pmc.c:256:8: error: implicit declaration of function 'amd_pmc_write_stb'; did you mean 'amd_pmc_read_stb'? [-Werror=implicit-function-declaration]
256 | ret = amd_pmc_write_stb(dev, AMD_PMC_STB_DUMMY_PC);
| ^~~~~~~~~~~~~~~~~
| amd_pmc_read_stb
There is now an easier way to handle this using DEFINE_SIMPLE_DEV_PM_OPS()
to replace all the #ifdefs, letting gcc drop any of the unused functions
silently.
Eric Dumazet [Tue, 7 Mar 2023 05:22:54 +0000 (05:22 +0000)]
netfilter: conntrack: adopt safer max chain length
Customers using GKE 1.25 and 1.26 are facing conntrack issues
root caused to commit c9c3b6811f74 ("netfilter: conntrack: make
max chain length random").
Even if we assume Uniform Hashing, a bucket often reachs 8 chained
items while the load factor of the hash table is smaller than 0.5
With a limit of 16, we reach load factors of 3.
With a limit of 32, we reach load factors of 11.
With a limit of 40, we reach load factors of 15.
With a limit of 50, we reach load factors of 24.
This patch changes MIN_CHAINLEN to 50, to minimize risks.
Ideally, we could in the future add a cushion based on expected
load factor (2 * nf_conntrack_max / nf_conntrack_buckets),
because some setups might expect unusual values.
Fixes: c9c3b6811f74 ("netfilter: conntrack: make max chain length random") Signed-off-by: Eric Dumazet <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
Jakub Kicinski [Tue, 7 Mar 2023 04:28:00 +0000 (20:28 -0800)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-03-06
We've added 8 non-merge commits during the last 7 day(s) which contain
a total of 9 files changed, 64 insertions(+), 18 deletions(-).
The main changes are:
1) Fix BTF resolver for DATASEC sections when a VAR points at a modifier,
that is, keep resolving such instances instead of bailing out,
from Lorenz Bauer.
2) Fix BPF test framework with regards to xdp_frame info misplacement
in the "live packet" code, from Alexander Lobakin.
3) Fix an infinite loop in BPF sockmap code for TCP/UDP/AF_UNIX,
from Liu Jian.
4) Fix a build error for riscv BPF JIT under PERF_EVENTS=n,
from Randy Dunlap.
5) Several BPF doc fixes with either broken links or external instead
of internal doc links, from Bagas Sanjaya.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: check that modifier resolves after pointer
btf: fix resolving BTF_KIND_VAR after ARRAY, STRUCT, UNION, PTR
bpf, test_run: fix &xdp_frame misplacement for LIVE_FRAMES
bpf, doc: Link to submitting-patches.rst for general patch submission info
bpf, doc: Do not link to docs.kernel.org for kselftest link
bpf, sockmap: Fix an infinite loop error when len is 0 in tcp_bpf_recvmsg_parser()
riscv, bpf: Fix patch_text implicit declaration
bpf, docs: Fix link to BTF doc
====================
Palmer Dabbelt [Thu, 23 Feb 2023 22:46:05 +0000 (14:46 -0800)]
RISC-V: Stop emitting attributes
The RISC-V ELF attributes don't contain any useful information. New
toolchains ignore them, but they frequently trip up various older/mixed
toolchains. So just turn them off.
scsi: sd: Fix wrong zone_write_granularity value during revalidate
When the sd driver revalidates host-managed SMR disks, it calls
disk_set_zoned() which changes the zone_write_granularity attribute value
to the logical block size regardless of the device type. After that, the sd
driver overwrites the value in sd_zbc_read_zone() with the physical block
size, since ZBC/ZAC requires this for host-managed disks. Between the calls
to disk_set_zoned() and sd_zbc_read_zone(), there exists a window where the
attribute shows the logical block size as the zone_write_granularity value,
which is wrong for host-managed disks. The duration of the window is from
20ms to 200ms, depending on report zone command execution time.
To avoid the wrong zone_write_granularity value between disk_set_zoned()
and sd_zbc_read_zone(), modify the value not in sd_zbc_read_zone() but
just after disk_set_zoned() call.
Michael Kelley [Mon, 27 Feb 2023 16:48:34 +0000 (08:48 -0800)]
scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
Hyper-V uses a VHD or VHDX file on the host as the underlying storage for a
virtual disk. The VHD/VHDX file format is a sparse format where real disk
space on the host is assigned in chunks that the VHD/VHDX file format calls
the BlockSize. This BlockSize is not to be confused with the 512-byte (or
4096-byte) sector size of the underlying storage device. The default block
size for a new VHD/VHDX file is 32 Mbytes. When a guest VM touches any
disk space within a 32 Mbyte chunk of the VHD/VHDX file, Hyper-V allocates
32 Mbytes of real disk space for that section of the VHD/VHDX. Similarly,
if a discard operation is done that covers an entire 32 Mbyte chunk,
Hyper-V will free the real disk space for that portion of the VHD/VHDX.
This BlockSize is surfaced in Linux as the "discard_granularity" in
/sys/block/sd<x>/queue, which makes sense.
Hyper-V also has differencing disks that can overlay a VHD/VHDX file to
capture changes to the VHD/VHDX while preserving the original VHD/VHDX.
One example of this differencing functionality is for VM snapshots. When a
snapshot is created, a differencing disk is created. If the snapshot is
rolled back, Hyper-V can just delete the differencing disk, and the VM will
see the original disk contents at the time the snapshot was taken.
Differencing disks are used in other scenarios as well.
The BlockSize for a differencing disk defaults to 2 Mbytes, not 32 Mbytes.
The smaller default is used because changes to differencing disks are
typically scattered all over, and Hyper-V doesn't want to allocate 32
Mbytes of real disk space for a stray write here or there. The smaller
BlockSize provides more efficient use of real disk space.
When a differencing disk is added to a VHD/VHDX, Hyper-V reports
UNIT_ATTENTION with a sense code indicating "Operating parameters have
changed", because the value of discard_granularity should be changed to 2
Mbytes. When the differencing disk is removed, discard_granularity should
be changed back to 32 Mbytes. However, current code simply reports a
message from scsi_report_sense() and the value of
/sys/block/sd<x>/queue/discard_granularity is not updated. The message
isn't very actionable by a sysadmin.
Fix this by having the storvsc driver check for the sense code indicating
that the underly VHD/VHDX block size has changed, and do a rescan of the
device to pick up the new discard_granularity. With this change the entire
transition to/from differencing disks is handled automatically and
transparently, with no confusing messages being output.
scsi: megaraid_sas: Add crash dump mode capability bit in MFI capabilities
In kdump kernel mode, the driver works in reduced functionality mode with
some features disabled such as reduced MSI-X count and RDPQ disabled, etc.
However, the firmware is not aware of this mode in some cases, which
results in undefined behavior.
To address this, the driver informs the firmware about the kdump mode
through MPI capabilities bit during driver initialization. This allows
firmware to adjust its behavior accordingly.
scsi: megaraid_sas: Update max supported LD IDs to 240
The firmware only supports Logical Disk IDs up to 240 and LD ID 255 (0xFF)
is reserved for deleted LDs. However, in some cases, firmware was assigning
LD ID 254 (0xFE) to deleted LDs and this was causing the driver to mark the
wrong disk as deleted. This in turn caused the wrong disk device to be
taken offline by the SCSI midlayer.
To address this issue, limit the LD ID range from 255 to 240. This ensures
the deleted LD ID is properly identified and removed by the driver without
accidently deleting any valid LDs.
Ranjan Kumar [Tue, 28 Feb 2023 14:08:35 +0000 (06:08 -0800)]
scsi: mpi3mr: Bad drive in topology results kernel crash
When the SAS Transport Layer support is enabled and a device exposed to
the OS by the driver fails INQUIRY commands, the driver frees up the memory
allocated for an internal HBA port data structure. However, in some places,
the reference to the freed memory is not cleared. When the firmware sends
the Device Info change event for the same device again, the freed memory is
accessed and that leads to memory corruption and OS crash.
Ranjan Kumar [Tue, 28 Feb 2023 14:08:34 +0000 (06:08 -0800)]
scsi: mpi3mr: NVMe command size greater than 8K fails
A wrong variable is checked while populating PRP entries in the PRP page
and this results in failure. No PRP entries in the PRP page were
successfully created and any NVMe Encapsulated commands with PRP of size
greater than 8K failed.
Ranjan Kumar [Tue, 28 Feb 2023 14:08:32 +0000 (06:08 -0800)]
scsi: mpi3mr: Wait for diagnostic save during controller init
If a controller reset operation is triggered to recover the controller from
a fault state, then wait for the snapdump to be saved in the firmware
region before proceeding to reset the controller.
Ranjan Kumar [Tue, 28 Feb 2023 14:08:30 +0000 (06:08 -0800)]
scsi: mpi3mr: ioctl timeout when disabling/enabling interrupt
As part of Task Management handling, the driver will disable and enable the
MSIx index zero which belongs to the Admin reply queue. During this
transition the driver loses some interrupts and this leads to Admin request
and ioctl timeouts.
After enabling the interrupts, poll the Admin reply queue to avoid
timeouts.
Jakob Koschel [Wed, 1 Mar 2023 17:19:14 +0000 (18:19 +0100)]
scsi: lpfc: Avoid usage of list iterator variable after loop
If the &epd_pool->list is empty when executing
lpfc_get_io_buf_from_expedite_pool() the function would return an invalid
pointer. Even in the case if the list is guaranteed to be populated, the
iterator variable should not be used after the loop to be more robust for
future changes.
Linus proposed to avoid any use of the list iterator variable after the
loop, in the attempt to move the list iterator variable declaration into
the macro to avoid any potential misuse after the loop [1].
Dan Carpenter [Mon, 27 Feb 2023 10:07:26 +0000 (13:07 +0300)]
scsi: ufs: ufs-qcom: Remove impossible check
The "dev_req_params" pointer points to inside the middle of a struct so it
can't be NULL. Removing this impossible condition is nice because now we
don't need to consider the correct error code for that situation.
projects / linux.git / log