Chris Wilson [Tue, 17 Sep 2019 19:47:46 +0000 (20:47 +0100)]
drm/i915: Extend Haswell GT1 PSMI workaround to all
A few times in CI, we have detected a GPU hang on our Haswell GT2
systems with the characteristic IPEHR of 0x780c0000. When the PSMI w/a
was first introducted, it was applied to all Haswell, but later on we
found an erratum that supposedly restricted the issue to GT1 and so
constrained it only be applied on GT1. That may have been a mistake...
Chris Wilson [Thu, 12 Sep 2019 16:08:34 +0000 (17:08 +0100)]
drm/i915: Don't mix srcu tag and negative error codes
While srcu may use an integer tag, it does not exclude potential error
codes and so may overlap with our own use of -EINTR. Use a separate
outparam to store the tag, and report the error code separately.
This allows userspace to use "legacy" mode for push constants, where
they are committed at 3DPRIMITIVE or flush time, rather than being
committed at 3DSTATE_BINDING_TABLE_POINTERS_XS time. Gen6-8 and Gen11
both use the "legacy" behavior - only Gen9 works in the "new" way.
Conflating push constants with binding tables is painful for userspace,
we would like to be able to avoid doing so.
Chris Wilson [Mon, 9 Sep 2019 11:00:08 +0000 (12:00 +0100)]
drm/i915: Perform GGTT restore much earlier during resume
As soon as we re-enable the various functions within the HW, they may go
off and read data via a GGTT offset. Hence, if we have not yet restored
the GGTT PTE before then, they may read and even *write* random locations
in memory.
Chris Wilson [Sat, 7 Sep 2019 10:50:46 +0000 (11:50 +0100)]
drm/i915/execlists: Remove incorrect BUG_ON for schedule-out
As we may unwind incomplete requests (for preemption) prior to
processing the CSB and the schedule-out events, we may update rq->engine
(resetting it to point back to the parent virtual engine) prior to
calling execlists_schedule_out(), invalidating the assertion that the
request still points to the inflight engine. (The likelihood of this is
increased if the CSB interrupt processing is pushed to the ksoftirqd for
being too slow and direct submission overtakes it.)
Tvrtko summarised it as:
"So unwind from direct submission resets rq->engine and races with
process_csb from the tasklet which notices request has actually
completed."
Commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of cmpxchg this would cause to reference function
__cmpxchg_called_with_bad_pointer, which is a error case
for catching bugs and will not happen for correct code, if
__cmpxchg is inlined.
Masahiro Yamada [Thu, 3 Oct 2019 07:58:26 +0000 (16:58 +0900)]
nsdeps: make generated patches independent of locale
scripts/nsdeps automatically generates a patch to add MODULE_IMPORT_NS
tags, and what is nicer, it sorts the lines alphabetically with the
'sort' command. However, the output from the 'sort' command depends on
locale.
So, this means people might potentially send different patches.
This kind of issue was reported in the past, for example,
commit f55f2328bb28 ("kbuild: make sorting initramfs contents
independent of locale").
Adding 'LANG=C' is a conventional way of fixing when a deterministic
result is desirable.
I added 'LANG=C' very close to the 'sort' command since changing
locale affects the language of error messages etc. We should respect
users' choice as much as possible.
Masahiro Yamada [Thu, 3 Oct 2019 07:58:24 +0000 (16:58 +0900)]
kbuild: fix build error of 'make nsdeps' in clean tree
Running 'make nsdeps' in a clean source tree fails as follows:
$ make -s clean; make -s defconfig; make nsdeps
[ snip ]
awk: fatal: cannot open file `init/modules.order' for reading (No such file or directory)
make: *** [Makefile;1307: modules.order] Error 2
make: *** Deleting file 'modules.order'
make: *** Waiting for unfinished jobs....
The cause of the error is 'make nsdeps' does not build modules at all.
Set KBUILD_MODULES to fix it.
Masahiro Yamada [Thu, 3 Oct 2019 07:58:23 +0000 (16:58 +0900)]
module: rename __kstrtab_ns_* to __kstrtabns_* to avoid symbol conflict
The module namespace produces __strtab_ns_<sym> symbols to store
namespace strings, but it does not guarantee the name uniqueness.
This is a potential problem because we have exported symbols starting
with "ns_".
For example, kernel/capability.c exports the following symbols:
The former expands to "__kstrtab_ns_capable" and "__kstrtab_ns_ns_capable",
and the latter to "__kstrtab_capable" and "__kstrtab_ns_capable".
Then, we have the duplicated "__kstrtab_ns_capable".
To ensure the uniqueness, rename "__kstrtab_ns_*" to "__kstrtabns_*".
Masahiro Yamada [Thu, 3 Oct 2019 07:58:22 +0000 (16:58 +0900)]
modpost: fix broken sym->namespace for external module builds
Currently, external module builds produce tons of false-positives:
WARNING: module <mod> uses symbol <sym> from namespace <ns>, but does not import it.
Here, the <ns> part shows a random string.
When you build external modules, the symbol info of vmlinux and
in-kernel modules are read from $(objtree)/Module.symvers, but
read_dump() is buggy in multiple ways:
[1] When the modpost is run for vmlinux and in-kernel modules,
sym_extract_namespace() allocates memory for the namespace. On the
other hand, read_dump() does not, then sym->namespace will point to
somewhere in the line buffer of get_next_line(). The data in the
buffer will be replaced soon, and sym->namespace will end up with
pointing to unrelated data. As a result, check_exports() will show
random strings in the warning messages.
[2] When there is no namespace, sym_extract_namespace() returns NULL.
On the other hand, read_dump() sets namespace to an empty string "".
(but, it will be later replaced with unrelated data due to bug [1].)
The check_exports() shows a warning unless exp->namespace is NULL,
so every symbol read from read_dump() emits the warning, which is
mostly false positive.
To address [1], sym_add_exported() calls strdup() for s->namespace.
The namespace from sym_extract_namespace() must be freed to avoid
memory leak.
For [2], I changed the if-conditional in check_exports().
This commit also fixes sym_add_exported() to set s->namespace correctly
when the symbol is preloaded.
Masahiro Yamada [Thu, 3 Oct 2019 07:58:21 +0000 (16:58 +0900)]
module: swap the order of symbol.namespace
Currently, EXPORT_SYMBOL_NS(_GPL) constructs the kernel symbol as
follows:
__ksymtab_SYMBOL.NAMESPACE
The sym_extract_namespace() in modpost allocates memory for the part
SYMBOL.NAMESPACE when '.' is contained. One problem is that the pointer
returned by strdup() is lost because the symbol name will be copied to
malloc'ed memory by alloc_symbol(). No one will keep track of the
pointer of strdup'ed memory.
sym->namespace still points to the NAMESPACE part. So, you can free it
with complicated code like this:
free(sym->namespace - strlen(sym->name) - 1);
It complicates memory free.
To fix it elegantly, I swapped the order of the symbol and the
namespace as follows:
__ksymtab_NAMESPACE.SYMBOL
then, simplified sym_extract_namespace() so that it allocates memory
only for the NAMESPACE part.
I prefer this order because it is intuitive and also matches to major
languages. For example, NAMESPACE::NAME in C++, MODULE.NAME in Python.
YueHaibing [Sun, 6 Oct 2019 04:44:56 +0000 (12:44 +0800)]
scripts: add_namespace: Fix coccicheck failed
Now all scripts in scripts/coccinelle to be automatically called
by coccicheck. However new adding add_namespace.cocci does not
support report mode, which make coccicheck failed.
This add "virtual report" to make the coccicheck go ahead smoothly.
Dave Young [Wed, 2 Oct 2019 16:59:04 +0000 (18:59 +0200)]
efi/x86: Do not clean dummy variable in kexec path
kexec reboot fails randomly in UEFI based KVM guest. The firmware
just resets while calling efi_delete_dummy_variable(); Unfortunately
I don't know how to debug the firmware, it is also possible a potential
problem on real hardware as well although nobody reproduced it.
The intention of the efi_delete_dummy_variable is to trigger garbage collection
when entering virtual mode. But SetVirtualAddressMap can only run once
for each physical reboot, thus kexec_enter_virtual_mode() is not necessarily
a good place to clean a dummy object.
Drop the efi_delete_dummy_variable so that kexec reboot can work.
efi/tpm: Only set 'efi_tpm_final_log_size' after successful event log parsing
If __calc_tpm2_event_size() fails to parse an event it will return 0,
resulting tpm2_calc_event_log_size() returning -1. Currently there is
no check of this return value, and 'efi_tpm_final_log_size' can end up
being set to this negative value resulting in a crash like this one:
BUG: unable to handle page fault for address: ffffbc8fc00866ad
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Also __calc_tpm2_event_size() returns a size of 0 when it fails
to parse an event, so update function documentation to reflect this.
The root cause of the issue that caused the failure of event parsing
in this case is resolved by Peter Jone's patchset dealing with large
event logs where crossing over a page boundary causes the page with
the event count to be unmapped.
Peter Jones [Wed, 2 Oct 2019 16:59:01 +0000 (18:59 +0200)]
efi/tpm: Don't traverse an event log with no events
When there are no entries to put into the final event log, some machines
will return the template they would have populated anyway. In this case
the nr_events field is 0, but the rest of the log is just garbage.
This patch stops us from trying to iterate the table with
__calc_tpm2_event_size() when the number of events in the table is 0.
Peter Jones [Wed, 2 Oct 2019 16:59:00 +0000 (18:59 +0200)]
efi/tpm: Don't access event->count when it isn't mapped
Some machines generate a lot of event log entries. When we're
iterating over them, the code removes the old mapping and adds a
new one, so once we cross the page boundary we're unmapping the page
with the count on it. Hilarity ensues.
This patch keeps the info from the header in local variables so we don't
need to access that page again or keep track of if it's mapped.
Ard Biesheuvel [Wed, 2 Oct 2019 16:58:59 +0000 (18:58 +0200)]
efivar/ssdt: Don't iterate over EFI vars if no SSDT override was specified
The kernel command line option efivar_ssdt= allows the name to be
specified of an EFI variable containing an ACPI SSDT table that should
be loaded into memory by the OS, and treated as if it was provided by
the firmware.
Currently, that code will always iterate over the EFI variables and
compare each name with the provided name, even if the command line
option wasn't set to begin with.
So bail early when no variable name was provided. This works around a
boot regression on the 2012 Mac Pro, as reported by Scott.
Will Deacon [Mon, 7 Oct 2019 12:03:12 +0000 (13:03 +0100)]
arm64: Kconfig: Make CONFIG_COMPAT_VDSO a proper Kconfig option
CONFIG_COMPAT_VDSO is defined by passing '-DCONFIG_COMPAT_VDSO' to the
compiler when the generic compat vDSO code is in use. It's much cleaner
and simpler to expose this as a proper Kconfig option (like x86 does),
so do that and remove the bodge.
Will Deacon [Fri, 4 Oct 2019 13:20:06 +0000 (14:20 +0100)]
arm64: vdso32: Rename COMPATCC to CC_COMPAT
For consistency with CROSS_COMPILE_COMPAT, mechanically rename COMPATCC
to CC_COMPAT so that specifying aspects of the compat vDSO toolchain in
the environment isn't needlessly confusing.
Will Deacon [Mon, 7 Oct 2019 11:27:59 +0000 (12:27 +0100)]
arm64: vdso32: Pass '--target' option to clang via VDSO_CAFLAGS
Directly passing the '--target' option to clang by appending to
COMPATCC does not work if COMPATCC has been specified explicitly as
an argument to Make unless the 'override' directive is used, which is
ugly and different to what is done in the top-level Makefile.
Move the '--target' option for clang out of COMPATCC and into
VDSO_CAFLAGS, where it will be picked up when compiling and assembling
the 32-bit vDSO under clang.
Will Deacon [Fri, 4 Oct 2019 14:44:45 +0000 (15:44 +0100)]
arm64: vdso32: Don't use KBUILD_CPPFLAGS unconditionally
KBUILD_CPPFLAGS is defined differently depending on whether the main
compiler is clang or not. This means that it is not possible to build
the compat vDSO with GCC if the rest of the kernel is built with clang.
Define VDSO_CPPFLAGS directly to break this dependency and allow a clang
kernel to build a compat vDSO with GCC:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- \
CROSS_COMPILE_COMPAT=arm-linux-gnueabihf- CC=clang \
COMPATCC=arm-linux-gnueabihf-gcc
Will Deacon [Fri, 4 Oct 2019 13:08:13 +0000 (14:08 +0100)]
arm64: Default to building compat vDSO with clang when CONFIG_CC_IS_CLANG
Rather than force the use of GCC for the compat cross-compiler, instead
extract the target from CROSS_COMPILE_COMPAT and pass it to clang if the
main compiler is clang.
Adam Ford [Sun, 6 Oct 2019 16:33:12 +0000 (11:33 -0500)]
serial: 8250_omap: Fix gpio check for auto RTS/CTS
There are two checks to see if the manual gpio is configured, but
these the check is seeing if the structure is NULL instead it
should check to see if there are CTS and/or RTS pins defined.
This patch uses checks for those individual pins instead of
checking for the structure itself to restore auto RTS/CTS.
Adam Ford [Sun, 6 Oct 2019 16:33:11 +0000 (11:33 -0500)]
serial: mctrl_gpio: Check for NULL pointer
When using mctrl_gpio_to_gpiod, it dereferences gpios into a single
requested GPIO. This dereferencing can break if gpios is NULL,
so this patch adds a NULL check before dereferencing it. If
gpios is NULL, this function will also return NULL.
Fix incorrect read-modify-write sequence in lpuart_flush_buffer() that
was reading from UARTPFIFO and writing to UARTCFIFO instead of
operating solely on the latter.
Pawel Laszczak [Mon, 7 Oct 2019 06:39:11 +0000 (07:39 +0100)]
usb:cdns3: Fix for CV CH9 running with g_zero driver.
Patch fixes issue with Halt Endnpoint Test observed during using g_zero
driver as DUT. Bug occurred only on some testing board.
Endpoint can defer transition to Halted state if endpoint has pending
requests.
Patch add additional condition that allows to return correct endpoint
status during Get Endpoint Status request even if the halting endpoint
is in progress.
Hans de Goede [Sat, 5 Oct 2019 21:04:49 +0000 (23:04 +0200)]
usb: dwc3: Remove dev_err() on platform_get_irq() failure
Since commit 7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() itself on
failure, so there is no need for the driver to also do this.
Hans de Goede [Sat, 5 Oct 2019 21:04:48 +0000 (23:04 +0200)]
usb: dwc3: Switch to platform_get_irq_byname_optional()
The dwc3 code to get the "peripheral" / "host" / "otg" IRQ first tries
platform_get_irq_byname() and then falls back to the IRQ at index 0 if
the platform_get_irq_byname().
In this case we do not want platform_get_irq_byname() to print an error
on failure, so switch to platform_get_irq_byname_optional() instead which
does not print an error.
Some drivers (e.g dwc3) first try to get an IRQ byname and then fall
back to the one at index 0. In this case we do not want the error(s)
printed by platform_get_irq_byname(). This commit adds a new
platform_get_irq_byname_optional(), which does not print errors, for this.
While at it also improve the kdoc text for platform_get_irq_byname() a bit.
arm64 was the last architecture using CROSS_COMPILE_COMPAT_VDSO config
option. With this patch series the dependency in the architecture has
been removed.
Remove CROSS_COMPILE_COMPAT_VDSO from the Unified vDSO library code.
arm64: vdso32: Detect binutils support for dmb ishld
Older versions of binutils (prior to 2.24) do not support the "ISHLD"
option for memory barrier instructions, which leads to a build failure
when assembling the vdso32 library.
Add a compilation time mechanism that detects if binutils supports those
instructions and configure the kernel accordingly.
The .config file and the generated include/config/auto.conf can
end up out of sync after a set of commands since
CONFIG_CROSS_COMPILE_COMPAT_VDSO is not updated correctly.
The sequence can be reproduced as follows:
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- defconfig
[...]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- menuconfig
[set CONFIG_CROSS_COMPILE_COMPAT_VDSO="arm-linux-gnueabihf-"]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-
Which results in:
arch/arm64/Makefile:62: CROSS_COMPILE_COMPAT not defined or empty,
the compat vDSO will not be built
even though the compat vDSO has been built:
$ file arch/arm64/kernel/vdso32/vdso.so
arch/arm64/kernel/vdso32/vdso.so: ELF 32-bit LSB pie executable, ARM,
EABI5 version 1 (SYSV), dynamically linked,
BuildID[sha1]=c67f6c786f2d2d6f86c71f708595594aa25247f6, stripped
A similar case that involves changing the configuration parameter
multiple times can be reconducted to the same family of problems.
Remove the use of CONFIG_CROSS_COMPILE_COMPAT_VDSO altogether and
instead rely on the cross-compiler prefix coming from the environment
via CROSS_COMPILE_COMPAT, much like we do for the rest of the kernel.
Mark Rutland [Fri, 4 Oct 2019 13:58:47 +0000 (14:58 +0100)]
arm64: mm: fix spurious fault detection
When detecting a spurious EL1 translation fault, we attempt to compare
ESR_EL1.DFSC with PAR_EL1.FST. We erroneously use FIELD_PREP() to
extract PAR_EL1.FST, when we should be using FIELD_GET().
In the wise words of Robin Murphy:
| FIELD_GET() is a UBFX, FIELD_PREP() is a BFI
Using FIELD_PREP() means that that dfsc & ESR_ELx_FSC_TYPE is always
zero, and hence not equal to ESR_ELx_FSC_FAULT. Thus we detect any
unhandled translation fault as spurious.
... so let's use FIELD_GET() to ensure we don't decide all translation
faults are spurious. ESR_EL1.DFSC occupies bits [5:0], and requires no
shifting.
Commit 7e534323c416 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:
drivers/mtd/nand/raw/au1550nd.c:443:57:
warning: pointer type mismatch in conditional expression
Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit 7e534323c416 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").
Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Pavel Shilovsky [Mon, 30 Sep 2019 17:06:18 +0000 (10:06 -0700)]
CIFS: Gracefully handle QueryInfo errors during open
Currently if the client identifies problems when processing
metadata returned in CREATE response, the open handle is being
leaked. This causes multiple problems like a file missing a lease
break by that client which causes high latencies to other clients
accessing the file. Another side-effect of this is that the file
can't be deleted.
Fix this by closing the file after the client hits an error after
the file was opened and the open descriptor wasn't returned to
the user space. Also convert -ESTALE to -EOPENSTALE to allow
the VFS to revalidate a dentry and retry the open.
cifs: use cifsInodeInfo->open_file_lock while iterating to avoid a panic
Commit 487317c99477 ("cifs: add spinlock for the openFileList to
cifsInodeInfo") added cifsInodeInfo->open_file_lock spin_lock to protect
the openFileList, but missed a few places where cifs_inode->openFileList
was enumerated. Change these remaining tcon->open_file_lock to
cifsInodeInfo->open_file_lock to avoid panic in is_size_safe_to_change.
Bill O'Donnell [Fri, 4 Oct 2019 23:38:44 +0000 (16:38 -0700)]
xfs: assure zeroed memory buffers for certain kmem allocations
Guarantee zeroed memory buffers for cases where potential memory
leak to disk can occur. In these cases, kmem_alloc is used and
doesn't zero the buffer, opening the possibility of information
leakage to disk.
Use existing infrastucture (xfs_buf_allocate_memory) to obtain
the already zeroed buffer from kernel memory.
This solution avoids the performance issue that would occur if a
wholesale change to replace kmem_alloc with kmem_zalloc was done.
Max Reitz [Mon, 30 Sep 2019 18:29:44 +0000 (11:29 -0700)]
xfs: Fix tail rounding in xfs_alloc_file_space()
To ensure that all blocks touched by the range [offset, offset + count)
are allocated, we need to calculate the block count from the difference
of the range end (rounded up) and the range start (rounded down).
Before this patch, we just round up the byte count, which may lead to
unaligned ranges not being fully allocated:
Linus Torvalds [Sun, 6 Oct 2019 20:53:27 +0000 (13:53 -0700)]
elf: don't use MAP_FIXED_NOREPLACE for elf executable mappings
In commit 4ed28639519c ("fs, elf: drop MAP_FIXED usage from elf_map") we
changed elf to use MAP_FIXED_NOREPLACE instead of MAP_FIXED for the
executable mappings.
Then, people reported that it broke some binaries that had overlapping
segments from the same file, and commit ad55eac74f20 ("elf: enforce
MAP_FIXED on overlaying elf segments") re-instated MAP_FIXED for some
overlaying elf segment cases. But only some - despite the summary line
of that commit, it only did it when it also does a temporary brk vma for
one obvious overlapping case.
Now Russell King reports another overlapping case with old 32-bit x86
binaries, which doesn't trigger that limited case. End result: we had
better just drop MAP_FIXED_NOREPLACE entirely, and go back to MAP_FIXED.
Yes, it's a sign of old binaries generated with old tool-chains, but we
do pride ourselves on not breaking existing setups.
This still leaves MAP_FIXED_NOREPLACE in place for the load_elf_interp()
and the old load_elf_library() use-cases, because nobody has reported
breakage for those. Yet.
Note that in all the cases seen so far, the overlapping elf sections
seem to be just re-mapping of the same executable with different section
attributes. We could possibly introduce a new MAP_FIXED_NOFILECHANGE
flag or similar, which acts like NOREPLACE, but allows just remapping
the same executable file using different protection flags.
It's not clear that would make a huge difference to anything, but if
people really hate that "elf remaps over previous maps" behavior, maybe
at least a more limited form of remapping would alleviate some concerns.
Alternatively, we should take a look at our elf_map() logic to see if we
end up not mapping things properly the first time.
In the meantime, this is the minimal "don't do that then" patch while
people hopefully think about it more.
Reported-by: Russell King <[email protected]> Fixes: 4ed28639519c ("fs, elf: drop MAP_FIXED usage from elf_map") Fixes: ad55eac74f20 ("elf: enforce MAP_FIXED on overlaying elf segments") Cc: Michal Hocko <[email protected]> Cc: Kees Cook <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
Linus Torvalds [Sun, 6 Oct 2019 18:10:15 +0000 (11:10 -0700)]
Merge tag 'dma-mapping-5.4-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping regression fix from Christoph Hellwig:
"Revert an incorret hunk from a patch that caused problems on various
arm boards (Andrey Smirnov)"
* tag 'dma-mapping-5.4-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: fix false positive warnings in dma_common_free_remap()
blk-wbt: fix performance regression in wbt scale_up/scale_down
scale_up wakes up waiters after scaling up. But after scaling max, it
should not wake up more waiters as waiters will not have anything to
do. This patch fixes this by making scale_up (and also scale_down)
return when threshold is reached.
This bug causes increased fdatasync latency when fdatasync and dd
conv=sync are performed in parallel on 4.19 compared to 4.14. This
bug was introduced during refactoring of blk-wbt code.
The commit was added as a quick band-aid for a hang that happened when a
block device was removed during system suspend. Now that bdi_wq is not
freezable anymore the hang should not be possible and we can get rid of
this hack by reverting it.
Mika Westerberg [Fri, 4 Oct 2019 10:00:24 +0000 (13:00 +0300)]
bdi: Do not use freezable workqueue
A removable block device, such as NVMe or SSD connected over Thunderbolt
can be hot-removed any time including when the system is suspended. When
device is hot-removed during suspend and the system gets resumed, kernel
first resumes devices and then thaws the userspace including freezable
workqueues. What happens in that case is that the NVMe driver notices
that the device is unplugged and removes it from the system. This ends
up calling bdi_unregister() for the gendisk which then schedules
wb_workfn() to be run one more time.
However, since the bdi_wq is still frozen flush_delayed_work() call in
wb_shutdown() blocks forever halting system resume process. User sees
this as hang as nothing is happening anymore.
Linus Torvalds [Sun, 6 Oct 2019 00:18:43 +0000 (17:18 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes this time around:
- Fixup of some clock specifications for DRA7 (device-tree fix)
- Removal of some dead/legacy CPU OPP/PM code for OMAP that throws
warnings at boot
- A few more minor fixups for OMAPs, most around display
- Enable STM32 QSPI as =y since their rootfs sometimes comes from
there
- Switch CONFIG_REMOTEPROC to =y since it went from tristate to bool
- Fix of thermal zone definition for ux500 (5.4 regression)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI support
ARM: dts: ux500: Fix up the CPU thermal zone
arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to y
ARM: dts: am4372: Set memory bandwidth limit for DISPC
ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage()
ARM: OMAP2+: Add missing LCDC midlemode for am335x
ARM: OMAP2+: Fix missing reset done flag for am3 and am43
ARM: dts: Fix gpio0 flags for am335x-icev2
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable DRM_TI_TFP410
DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again
ARM: dts: Fix wrong clocks for dra7 mcasp
clk: ti: dra7: Fix mcasp8 clock bits
Linus Torvalds [Sat, 5 Oct 2019 19:56:59 +0000 (12:56 -0700)]
Merge tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- remove unneeded ar-option and KBUILD_ARFLAGS
- remove long-deprecated SUBDIRS
- fix modpost to suppress false-positive warnings for UML builds
- fix namespace.pl to handle relative paths to ${objtree}, ${srctree}
- make setlocalversion work for /bin/sh
- make header archive reproducible
- fix some Makefiles and documents
* tag 'kbuild-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kheaders: make headers archive reproducible
kbuild: update compile-test header list for v5.4-rc2
kbuild: two minor updates for Documentation/kbuild/modules.rst
scripts/setlocalversion: clear local variable to make it work for sh
namespace: fix namespace.pl script to support relative paths
video/logo: do not generate unneeded logo C files
video/logo: remove unneeded *.o pattern from clean-files
integrity: remove pointless subdir-$(CONFIG_...)
integrity: remove unneeded, broken attempt to add -fshort-wchar
modpost: fix static EXPORT_SYMBOL warnings for UML build
kbuild: correct formatting of header in kbuild module docs
kbuild: remove SUBDIRS support
kbuild: remove ar-option and KBUILD_ARFLAGS
Linus Torvalds [Sat, 5 Oct 2019 19:53:27 +0000 (12:53 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Twelve patches mostly small but obvious fixes or cosmetic but small
updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix Nport ID display value
scsi: qla2xxx: Fix N2N link up fail
scsi: qla2xxx: Fix N2N link reset
scsi: qla2xxx: Optimize NPIV tear down process
scsi: qla2xxx: Fix stale mem access on driver unload
scsi: qla2xxx: Fix unbound sleep in fcport delete path.
scsi: qla2xxx: Silence fwdump template message
scsi: hisi_sas: Make three functions static
scsi: megaraid: disable device when probe failed after enabled device
scsi: storvsc: setup 1:1 mapping between hardware queue and CPU queue
scsi: qedf: Remove always false 'tmp_prio < 0' statement
scsi: ufs: skip shutdown if hba is not powered
scsi: bnx2fc: Handle scope bits when array returns BUSY or TSF
Linus Torvalds [Sat, 5 Oct 2019 19:03:27 +0000 (12:03 -0700)]
Merge branch 'readdir' (readdir speedup and sanity checking)
This makes getdents() and getdents64() do sanity checking on the
pathname that it gives to user space. And to mitigate the performance
impact of that, it first cleans up the way it does the user copying, so
that the code avoids doing the SMAP/PAN updates between each part of the
dirent structure write.
I really wanted to do this during the merge window, but didn't have
time. The conversion of filldir to unsafe_put_user() is something I've
had around for years now in a private branch, but the extra pathname
checking finally made me clean it up to the point where it is mergable.
It's worth noting that the filename validity checking really should be a
bit smarter: it would be much better to delay the error reporting until
the end of the readdir, so that non-corrupted filenames are still
returned. But that involves bigger changes, so let's see if anybody
actually hits the corrupt directory entry case before worrying about it
further.
* branch 'readdir':
Make filldir[64]() verify the directory entry filename is valid
Convert filldir[64]() from __put_user() to unsafe_put_user()
Linus Torvalds [Sat, 5 Oct 2019 18:32:52 +0000 (11:32 -0700)]
Make filldir[64]() verify the directory entry filename is valid
This has been discussed several times, and now filesystem people are
talking about doing it individually at the filesystem layer, so head
that off at the pass and just do it in getdents{64}().
This is partially based on a patch by Jann Horn, but checks for NUL
bytes as well, and somewhat simplified.
There's also commentary about how it might be better if invalid names
due to filesystem corruption don't cause an immediate failure, but only
an error at the end of the readdir(), so that people can still see the
filenames that are ok.
There's also been discussion about just how much POSIX strictly speaking
requires this since it's about filesystem corruption. It's really more
"protect user space from bad behavior" as pointed out by Jann. But
since Eric Biederman looked up the POSIX wording, here it is for context:
"From readdir:
The readdir() function shall return a pointer to a structure
representing the directory entry at the current position in the
directory stream specified by the argument dirp, and position the
directory stream at the next entry. It shall return a null pointer
upon reaching the end of the directory stream. The structure dirent
defined in the <dirent.h> header describes a directory entry.
From definitions:
3.129 Directory Entry (or Link)
An object that associates a filename with a file. Several directory
entries can associate names with the same file.
...
3.169 Filename
A name consisting of 1 to {NAME_MAX} bytes used to name a file. The
characters composing the name may be selected from the set of all
character values excluding the slash character and the null byte. The
filenames dot and dot-dot have special meaning. A filename is
sometimes referred to as a 'pathname component'."
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
Also note that if this ends up being noticeable as a performance
regression, we can fix that to do a much more optimized model that
checks for both NUL and '/' at the same time one word at a time.
We haven't really tended to optimize 'memchr()', and it only checks for
one pattern at a time anyway, and we really _should_ check for NUL too
(but see the comment about "soft errors" in the code about why it
currently only checks for '/')
See the CONFIG_DCACHE_WORD_ACCESS case of hash_name() for how the name
lookup code looks for pathname terminating characters in parallel.
Linus Torvalds [Sun, 22 May 2016 04:59:07 +0000 (21:59 -0700)]
Convert filldir[64]() from __put_user() to unsafe_put_user()
We really should avoid the "__{get,put}_user()" functions entirely,
because they can easily be mis-used and the original intent of being
used for simple direct user accesses no longer holds in a post-SMAP/PAN
world.
Manually optimizing away the user access range check makes no sense any
more, when the range check is generally much cheaper than the "enable
user accesses" code that the __{get,put}_user() functions still need.
So instead of __put_user(), use the unsafe_put_user() interface with
user_access_{begin,end}() that really does generate better code these
days, and which is generally a nicer interface. Under some loads, the
multiple user writes that filldir() does are actually quite noticeable.
This also makes the dirent name copy use unsafe_put_user() with a couple
of macros. We do not want to make function calls with SMAP/PAN
disabled, and the code this generates is quite good when the
architecture uses "asm goto" for unsafe_put_user() like x86 does.
Note that this doesn't bother with the legacy cases. Nobody should use
them anyway, so performance doesn't really matter there.
1) Fix ieeeu02154 atusb driver use-after-free, from Johan Hovold.
2) Need to validate TCA_CBQ_WRROPT netlink attributes, from Eric
Dumazet.
3) txq null deref in mac80211, from Miaoqing Pan.
4) ionic driver needs to select NET_DEVLINK, from Arnd Bergmann.
5) Need to disable bh during nft_connlimit GC, from Pablo Neira Ayuso.
6) Avoid division by zero in taprio scheduler, from Vladimir Oltean.
7) Various xgmac fixes in stmmac driver from Jose Abreu.
8) Avoid 64-bit division in mlx5 leading to link errors on 32-bit from
Michal Kubecek.
9) Fix bad VLAN check in rtl8366 DSA driver, from Linus Walleij.
10) Fix sleep while atomic in sja1105, from Vladimir Oltean.
11) Suspend/resume deadlock in stmmac, from Thierry Reding.
12) Various UDP GSO fixes from Josh Hunt.
13) Fix slab out of bounds access in tcp_zerocopy_receive(), from Eric
Dumazet.
14) Fix OOPS in __ipv6_ifa_notify(), from David Ahern.
15) Memory leak in NFC's llcp_sock_bind, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
selftests/net: add nettest to .gitignore
net: qlogic: Fix memory leak in ql_alloc_large_buffers
nfc: fix memory leak in llcp_sock_bind()
sch_dsmark: fix potential NULL deref in dsmark_init()
net: phy: at803x: use operating parameters from PHY-specific status
net: phy: extract pause mode
net: phy: extract link partner advertisement reading
net: phy: fix write to mii-ctrl1000 register
ipv6: Handle missing host route in __ipv6_ifa_notify
net: phy: allow for reset line to be tied to a sleepy GPIO controller
net: ipv4: avoid mixed n_redirects and rate_tokens usage
r8152: Set macpassthru in reset_resume callback
cxgb4:Fix out-of-bounds MSI-X info array access
Revert "ipv6: Handle race in addrconf_dad_work"
net: make sock_prot_memory_pressure() return "const char *"
rxrpc: Fix rxrpc_recvmsg tracepoint
qmi_wwan: add support for Cinterion CLS8 devices
tcp: fix slab-out-of-bounds in tcp_zerocopy_receive()
lib: textsearch: fix escapes in example code
udp: only do GSO if # of segs > 1
...
Linus Torvalds [Sat, 5 Oct 2019 15:44:02 +0000 (08:44 -0700)]
Merge tag 's390-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- defconfig updates
- Fix build errors with CC_OPTIMIZE_FOR_SIZE due to usage of "i"
constraint for function arguments. Two kvm changes acked-by Christian
Borntraeger.
- Fix -Wunused-but-set-variable warnings in mm code.
- Avoid a constant misuse in qdio.
- Handle a case when cpumf is temporarily unavailable.
* tag 's390-5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
KVM: s390: mark __insn32_query() as __always_inline
KVM: s390: fix __insn32_query() inline assembly
s390: update defconfigs
s390/pci: mark function(s) __always_inline
s390/mm: mark function(s) __always_inline
s390/jump_label: mark function(s) __always_inline
s390/cpu_mf: mark function(s) __always_inline
s390/atomic,bitops: mark function(s) __always_inline
s390/mm: fix -Wunused-but-set-variable warnings
s390: mark __cpacf_query() as __always_inline
s390/qdio: clarify size of the QIB parm area
s390/cpumf: Fix indentation in sampling device driver
s390/cpumsf: Check for CPU Measurement sampling
s390/cpumf: Use consistant debug print format
Heiko Carstens [Wed, 2 Oct 2019 12:34:37 +0000 (14:34 +0200)]
KVM: s390: mark __insn32_query() as __always_inline
__insn32_query() will not compile if the compiler decides to not
inline it, since it contains an inline assembly with an "i" constraint
with variable contents.
Heiko Carstens [Wed, 2 Oct 2019 12:24:47 +0000 (14:24 +0200)]
KVM: s390: fix __insn32_query() inline assembly
The inline assembly constraints of __insn32_query() tell the compiler
that only the first byte of "query" is being written to. Intended was
probably that 32 bytes are written to.
Fix and simplify the code and just use a "memory" clobber.
Fixes: d668139718a9 ("KVM: s390: provide query function for instructions returning 32 byte") Cc: [email protected] # v5.2+ Acked-by: Christian Borntraeger <[email protected]> Signed-off-by: Heiko Carstens <[email protected]> Signed-off-by: Vasily Gorbik <[email protected]>
Restore original invalid input check in dma_common_free_remap() to
avoid this problem.
Fixes: 5cf4537975bb ("dma-mapping: introduce a dma_common_find_pages helper") Signed-off-by: Andrey Smirnov <[email protected]>
[hch: just revert the offending hunk instead of creating a new helper] Signed-off-by: Christoph Hellwig <[email protected]>
Dmitry Goldin [Fri, 4 Oct 2019 10:40:07 +0000 (10:40 +0000)]
kheaders: make headers archive reproducible
In commit 43d8ce9d65a5 ("Provide in-kernel headers to make
extending kernel easier") a new mechanism was introduced, for kernels
>=5.2, which embeds the kernel headers in the kernel image or a module
and exposes them in procfs for use by userland tools.
The archive containing the header files has nondeterminism caused by
header files metadata. This patch normalizes the metadata and utilizes
KBUILD_BUILD_TIMESTAMP if provided and otherwise falls back to the
default behaviour.
In commit f7b101d33046 ("kheaders: Move from proc to sysfs") it was
modified to use sysfs and the script for generation of the archive was
renamed to what is being patched.
Masahiro Yamada [Thu, 3 Oct 2019 02:36:29 +0000 (11:36 +0900)]
kbuild: update compile-test header list for v5.4-rc2
Commit 6dc280ebeed2 ("coda: remove uapi/linux/coda_psdev.h") removed
a header in question. Some more build errors were fixed. Add more
headers into the test coverage.
Masahiro Yamada [Tue, 1 Oct 2019 12:17:24 +0000 (21:17 +0900)]
scripts/setlocalversion: clear local variable to make it work for sh
Geert Uytterhoeven reports a strange side-effect of commit 858805b336be
("kbuild: add $(BASH) to run scripts with bash-extension"), which
inserts the contents of a localversion file in the build directory twice.
[Steps to Reproduce]
$ echo bar > localversion
$ mkdir build
$ cd build/
$ echo foo > localversion
$ make -s -f ../Makefile defconfig include/config/kernel.release
$ cat include/config/kernel.release
5.4.0-rc1foofoobar
This comes down to the behavior change of local variables.
The 'man sh' on my Ubuntu machine, where sh is an alias to dash,
explains as follows:
When a variable is made local, it inherits the initial value and
exported and readonly flags from the variable with the same name
in the surrounding scope, if there is one. Otherwise, the variable
is initially unset.
[Test Code]
foo ()
{
local res
echo "res: $res"
}
res=1
foo
[Result]
$ sh test.sh
res: 1
$ bash test.sh
res:
So, scripts/setlocalversion correctly works only for bash in spite of
its hashbang being #!/bin/sh. Nobody had noticed it before because
CONFIG_SHELL was previously set to bash almost all the time.
Now that CONFIG_SHELL is set to sh, we must write portable and correct
code. I gave the Fixes tag to the commit that uncovered the issue.
Clear the variable 'res' in collect_files() to make it work for sh
(and it also works on distributions where sh is an alias to bash).
Fixes: 858805b336be ("kbuild: add $(BASH) to run scripts with bash-extension") Reported-by: Geert Uytterhoeven <[email protected]> Signed-off-by: Masahiro Yamada <[email protected]> Tested-by: Geert Uytterhoeven <[email protected]>
Jacob Keller [Fri, 27 Sep 2019 23:30:27 +0000 (16:30 -0700)]
namespace: fix namespace.pl script to support relative paths
The namespace.pl script does not work properly if objtree is not set to
an absolute path. The do_nm function is run from within the find
function, which changes directories.
Because of this, appending objtree, $File::Find::dir, and $source, will
return a path which is not valid from the current directory.
This used to work when objtree was set to an absolute path when using
"make namespacecheck". It appears to have not worked when calling
./scripts/namespace.pl directly.
This behavior was changed in 7e1c04779efd ("kbuild: Use relative path
for $(objtree)", 2014-05-14)
Rather than fixing the Makefile to set objtree to an absolute path, just
fix namespace.pl to work when srctree and objtree are relative. Also fix
the script to use an absolute path for these by default.
Use the File::Spec module for this purpose. It's been part of perl
5 since 5.005.
The curdir() function is used to get the current directory when the
objtree and srctree aren't set in the environment.
rel2abs() is used to convert possibly relative objtree and srctree
environment variables to absolute paths.
Finally, the catfile() function is used instead of string appending
paths together, since this is more robust when joining paths together.
Masahiro Yamada [Wed, 21 Aug 2019 04:12:35 +0000 (13:12 +0900)]
video/logo: do not generate unneeded logo C files
Currently, all the logo C files are generated irrespective of the
CONFIG options. Adding them to extra-y is wrong. What we need to do
here is to add them to 'targets' so that if_changed works properly.
Files listed in 'targets' are cleaned, so clean-files is unneeded.
integrity: remove unneeded, broken attempt to add -fshort-wchar
I guess commit 15ea0e1e3e18 ("efi: Import certificates from UEFI Secure
Boot") attempted to add -fshort-wchar for building load_uefi.o, but it
has never worked as intended.
load_uefi.o is created in the platform_certs/ sub-directory. If you
really want to add -fshort-wchar, the correct code is:
Navid Emamdoost [Fri, 4 Oct 2019 20:24:39 +0000 (15:24 -0500)]
net: qlogic: Fix memory leak in ql_alloc_large_buffers
In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.
Fixes: 0f8ab89e825f ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()") Signed-off-by: Navid Emamdoost <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Fixes: 30cc4587659e ("NFC: Move LLCP code to the NFC top level diirectory") Signed-off-by: Eric Dumazet <[email protected]> Reported-by: syzbot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Fixes: 758cc43c6d73 ("[PKT_SCHED]: Fix dsmark to apply changes consistent") Signed-off-by: Eric Dumazet <[email protected]> Reported-by: syzbot <[email protected]> Signed-off-by: David S. Miller <[email protected]>
====================
Fix regression with AR8035 speed downgrade
The following series attempts to address an issue spotted by tinywrkb
with the AR8035 on the Cubox-i2 in a situation where the PHY downgrades
the negotiated link.
This is version 2, not much has changed other than rebasing on the
current net tree. Changes have happend to patch 2 due to conflicts,
so I dropped Andrew's reviewed-by. Minor context changes to patch 4
which I don't consider important enough to warrant dropping the
reviewed-by.
Before commit 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in
genphy_read_status"), we would read not only the link partner's
advertisement, but also our own advertisement from the PHY registers,
and use both to derive the PHYs current link mode. This works when the
AR8035 downgrades the speed, because it appears that the AR8035 clears
link mode bits in the advertisement registers as part of the downgrade.
Commentary: what is not yet known is whether the AR8035 restores the
advertisement register when the link goes down to the
previous state.
However, since the above referenced commit, we no longer use the PHYs
advertisement registers, instead converting the link partner's
advertisement to the ethtool link mode array, and combine that with
phylib's cached version of our advertisement - which is not updated on
speed downgrade.
This results in phylib disagreeing with the actual operating mode of
the PHY.
Commentary: I wonder how many more PHY drivers are broken by this
commit, but have yet to be discovered.
The obvious way to address this would be to disable the downgrade
feature, and indeed this does fix the problem in tinywrkb's case - his
link partner instead downgrades the speed by reducing its
advertisement, resulting in phylib correctly evaluating a slower speed.
However, it has a serious drawback - the gigabit control register (MII
register 9) appears to become read only. It seems the only way to
update the register is to re-enable the downgrade feature, reset the
PHY, changing register 9, disable the downgrade feature, and reset the
PHY again.
This series attempts to address the problem using a different approach,
similar to the approach taken with Marvell PHYs. The AR8031, AR8033
and AR8035 have a PHY-Specific Status register which reports the
actual operating mode of the PHY - both speed and duplex. This
register correctly reports the operating mode irrespective of whether
autoneg is enabled or not. We use this register to fill in phylib's
speed and duplex parameters.
In detail:
Patch 1 fixes a bug where writing to register 9 does not update
phylib's advertisement mask in the same way that writing register 4
does; this looks like an omission from when gigabit PHY support came
into being.
Patch 2 seperates the generic phylib code which reads the link partners
advertisement from the PHY, so that we can re-use this in the Atheros
PHY driver.
Patch 3 seperates the generic phylib pause mode; phylib provides no
help for MAC drivers to ascertain the negotiated pause mode, it merely
copies the link partner's pause mode bits into its own variables.
Commentary: Both the aforementioned Atheros PHYs and Marvell PHYs
provide the resolved pause modes in terms of whether
we should transmit pause frames, or whether we should
allow reception of pause frames. Surely the resolution
of this should be in phylib?
Patch 4 provides the Atheros PHY driver with a private "read_status"
implementation that fills in phylib's speed and duplex settings
depending on the PHY-Specific status register. This ensures that
phylib and the MAC driver match the operating mode that the PHY has
decided to use. Since the register also gives us MDIX status, we
can trivially fill that status in as well.
Note that, although the bits mentioned in this patch for this register
match those in th Marvell PHY driver, and it is located at the same
address, the meaning of other register bits varies between the PHYs.
Therefore, I do not feel that it would be appropriate to make this some
kind of generic function.
====================
Russell King [Fri, 4 Oct 2019 16:06:14 +0000 (17:06 +0100)]
net: phy: at803x: use operating parameters from PHY-specific status
Read the PHY-specific status register for the current operating mode
(speed and duplex) of the PHY. This register reflects the actual
mode that the PHY has resolved depending on either the advertisements
of autoneg is enabled, or the forced mode if autoneg is disabled.
This ensures that phylib's software state always tracks the hardware
state.
It seems both AR8033 (which uses the AR8031 ID) and AR8035 support
this status register. AR8030 is not known at the present time.
This patch depends on "net: phy: extract pause mode" and "net: phy:
extract link partner advertisement reading".
Russell King [Fri, 4 Oct 2019 16:06:09 +0000 (17:06 +0100)]
net: phy: extract pause mode
Extract the update of phylib's software pause mode state from
genphy_read_status(), so that we can re-use this functionality with
PHYs that have alternative ways to read the negotiation results.
Russell King [Fri, 4 Oct 2019 16:06:04 +0000 (17:06 +0100)]
net: phy: extract link partner advertisement reading
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function. This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.
Russell King [Fri, 4 Oct 2019 16:05:58 +0000 (17:05 +0100)]
net: phy: fix write to mii-ctrl1000 register
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation. However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither. This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.
Fixes: 5502b218e001 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status") Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: Russell King <[email protected]> Signed-off-by: David S. Miller <[email protected]>
addrconf_dad_work is kicked to be scheduled when a device is brought
up. There is a race between addrcond_dad_work getting scheduled and
taking the rtnl lock and a process taking the link down (under rtnl).
The latter removes the host route from the inet6_addr as part of
addrconf_ifdown which is run for NETDEV_DOWN. The former attempts
to use the host route in __ipv6_ifa_notify. If the down event removes
the host route due to the race to the rtnl, then the BUG listed above
occurs.
Since the DAD sequence can not be aborted, add a check for the missing
host route in __ipv6_ifa_notify. The only way this should happen is due
to the previously mentioned race. The host route is created when the
address is added to an interface; it is only removed on a down event
where the address is kept. Add a warning if the host route is missing
AND the device is up; this is a situation that should never happen.
Andrea Merello [Fri, 4 Oct 2019 13:53:32 +0000 (15:53 +0200)]
net: phy: allow for reset line to be tied to a sleepy GPIO controller
mdio_device_reset() makes use of the atomic-pretending API flavor for
handling the PHY reset GPIO line.
I found no hint that mdio_device_reset() is called from atomic context
and indeed it uses usleep_range() since long time, so I would assume that
it is OK to sleep there.
This patch switch to gpiod_set_value_cansleep() in mdio_device_reset().
This is relevant if e.g. the PHY reset line is tied to a I2C GPIO
controller.
This has been tested on a ZynqMP board running an upstream 4.19 kernel and
then hand-ported on current kernel tree.
Paolo Abeni [Fri, 4 Oct 2019 13:11:17 +0000 (15:11 +0200)]
net: ipv4: avoid mixed n_redirects and rate_tokens usage
Since commit c09551c6ff7f ("net: ipv4: use a dedicated counter
for icmp_v4 redirect packets") we use 'n_redirects' to account
for redirect packets, but we still use 'rate_tokens' to compute
the redirect packets exponential backoff.
If the device sent to the relevant peer any ICMP error packet
after sending a redirect, it will also update 'rate_token' according
to the leaking bucket schema; typically 'rate_token' will raise
above BITS_PER_LONG and the redirect packets backoff algorithm
will produce undefined behavior.
Fix the issue using 'n_redirects' to compute the exponential backoff
in ip_rt_send_redirect().
Note that we still clear rate_tokens after a redirect silence period,
to avoid changing an established behaviour.
The root cause predates git history; before the mentioned commit in
the critical scenario, the kernel stopped sending redirects, after
the mentioned commit the behavior more randomic.
Reported-by: Xiumei Mu <[email protected]> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: c09551c6ff7f ("net: ipv4: use a dedicated counter for icmp_v4 redirect packets") Signed-off-by: Paolo Abeni <[email protected]> Acked-by: Lorenzo Bianconi <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Kai-Heng Feng [Fri, 4 Oct 2019 12:51:04 +0000 (20:51 +0800)]
r8152: Set macpassthru in reset_resume callback
r8152 may fail to establish network connection after resume from system
suspend.
If the USB port connects to r8152 lost its power during system suspend,
the MAC address was written before is lost. The reason is that The MAC
address doesn't get written again in its reset_resume callback.
So let's set MAC address again in reset_resume callback. Also remove
unnecessary lock as no other locking attempt will happen during
reset_resume.
Vishal Kulkarni [Thu, 3 Oct 2019 22:36:15 +0000 (04:06 +0530)]
cxgb4:Fix out-of-bounds MSI-X info array access
When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.
Fixes: 94cdb8bb993a ("cxgb4: Add support for dynamic allocation of resources for ULD") Signed-off-by: Shahjada Abul Husain <[email protected]> Signed-off-by: Vishal Kulkarni <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Eric reported tests failings with commit. After digging into it,
the bottom line is that the DAD sequence is not to be messed with.
There are too many cases that are expected to proceed regardless
of whether a device is up.
Revert the patch and I will send a different solution for the
problem Rajendra reported.
David Howells [Thu, 3 Oct 2019 16:44:44 +0000 (17:44 +0100)]
rxrpc: Fix rxrpc_recvmsg tracepoint
Fix the rxrpc_recvmsg tracepoint to handle being called with a NULL call
parameter.
Fixes: a25e21f0bcd2 ("rxrpc, afs: Use debug_ids rather than pointers in traces") Signed-off-by: David Howells <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Fri, 4 Oct 2019 20:02:47 +0000 (13:02 -0700)]
Merge tag 'riscv/for-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
- Ensure that exclusive-load reservations are terminated after system
call or exception handling. This primarily affects QEMU, which does
not expire load reservations.
- Fix an issue primarily affecting RV32 platforms that can cause the DT
header to be corrupted, causing boot failures.
* tag 'riscv/for-v5.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix memblock reservation for device tree blob
RISC-V: Clear load reservations while restoring hart contexts
projects / linux.git / log