USB: revert portions of "UNUSUAL_DEV: Sync up some reported devices from Ubuntu"
This reverts one change from 67fa10627ec0d8aa16f1cf38cf527e67d8097d3c
that prevented userspace from seing the "driver disk" lun in a san disk
device. The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.
usb: Remove broken optimisation in OHCI IRQ handler
The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.
This mechanism can't be used on some controllers. Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.
This patch removes the optimisation and makes the code clearer.
Nicolas Ferre [Thu, 13 Dec 2007 23:52:58 +0000 (15:52 -0800)]
USB: at91_udc: correct hanging while disconnecting usb cable
Correct hanging while disconnecting the USB device cable. Prevent a race
between vbus and UDP interrupts. This bug was tracked on at91sam9260ek
boards.
A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock). A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Alan Stern [Thu, 6 Dec 2007 19:47:08 +0000 (14:47 -0500)]
USB: use IRQF_DISABLED for HCD interrupt handlers
Host controller IRQs are supposed to be serviced with interrupts
disabled. This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it. It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().
Alan Stern [Tue, 11 Dec 2007 21:02:23 +0000 (16:02 -0500)]
USB: fix locking loop by avoiding flush_scheduled_work
This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().
Jeff Long [Wed, 28 Nov 2007 16:02:09 +0000 (11:02 -0500)]
USB: cp2101: new device id
This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102. I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.
Doug Maxey [Thu, 6 Dec 2007 05:36:45 +0000 (23:36 -0600)]
usb-storage: Fix devices that cannot handle 32k transfers
When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.
The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.
HOWTO: Change man-page maintainer address for Japanese HOWTO
Below is a patch to change email address of man-page maintainer for
Japanese HOWTO document (Documentation/ja_JP/HOWTO).
This is for sync to Documentation/HOWTO that Michael Kerrisk mentioned
to me.
Romain Liévin [Sat, 1 Dec 2007 07:51:58 +0000 (08:51 +0100)]
tipar: remove obsolete module
tipar: remove obsolete module
The tipar character driver was used to implement bit-banging access
to Texas Instruments parallel link cable. A user-land method now
exists thru PPDEV & PARPORT.
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] add Nano 7240 driver
[WATCHDOG] ipmi: add the standard watchdog timeout ioctls
[WATCHDOG] IT8212F watchdog driver
[WATCHDOG] Sbus: cpwatchdog, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] bfin_wdt, remove SPIN_LOCK_UNLOCKED
[WATCHDOG] Stop looking for device as soon as one is found
[WATCHDOG] at32ap700x_wdt: add support for boot status and add fix for silicon errata
Linus Torvalds [Mon, 17 Dec 2007 17:52:11 +0000 (09:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix lock flag variable location, bump version number
IB/ehca: Serialize HCA-related hCalls if necessary
IB/ehca: Return correct number of SGEs for SRQ
Uwe Kleine-König [Thu, 13 Dec 2007 08:31:34 +0000 (09:31 +0100)]
[ARM] 4710/1: Fix coprocessor 14 usage for debug messages via ICEDCC
According to ARM7TDMI Technical Reference Manual (ARM DDI 0210C) writing
to the DCC data write register coproc dest registers are 1 and 0, not 0
and 1.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA]: irda parameters warning fixes.
[IRDA]: stir4200 fixes.
[IRDA]: irlmp_unregister_link() needs to free lsaps.
[IRDA]: mcs7780 needs to free allocated rx buffer.
[IRDA]: Race between open and disconnect in irda-usb.
[SCTP]: Flush fragment queue when exiting partial delivery.
[AX25]: Locking dependencies fix in ax25_disconnect().
[IPV4]: Make tcp_input_metrics() get minimum RTO via tcp_rto_min()
[IPV6]: Fix the return value of ipv6_getsockopt
[BRIDGE]: Assign random address.
[IPV4]: Updates to nfsroot documentation
[ATM]: Fix compiler warning noise with FORE200E driver
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
[SYNCPPP]: Endianness and 64bit fixes.
[TIPC]: Fix semaphore handling.
[NETFILTER]: xt_hashlimit should use time_after_eq()
[XFRM]: Display the audited SPI value in host byte order.
[NETFILTER]: ip_tables: fix compat copy race
[NETFILTER]: ctnetlink: set expected bit for related conntracks
Linus Torvalds [Mon, 17 Dec 2007 16:41:56 +0000 (08:41 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Make PS3_SYS_MANAGER default y, not m
[POWERPC] Fix rounding bug in emulation for double float operating
[POWERPC] iSeries: don't printk with HV spinlock held
[POWERPC] 82xx: mpc8272ads, pq2fads: Update defconfig with CONFIG_FS_ENET_MDIO_FCC
[POWRPC] CPM2: Eliminate section mismatch warning in cpm2_reset().
[POWERPC] Kill non-existent symbols from ksyms and commproc.h
[POWERPC] Fix typo #ifdef -> #ifndef
Linus Torvalds [Mon, 17 Dec 2007 16:41:25 +0000 (08:41 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Ensure that ST0_FR is never set on a 32 bit kernel
[MIPS] time: Delete weak definition of plat_time_init() due to gcc bug.
[MIPS] PCI: Make pcibios_fixup_device_resources ignore legacy resources.
[MIPS] Atlas, Malta: Don't free firmware memory on free_initmem.
[MIPS] Alchemy: fix off by two error in __fixup_bigphys_addr()
[MIPS] Alchemy: fix PCI resource conflict
[MIPS] time: Set up Cobalt's mips_hpt_frequency
Git commit 3610cce87af0693603db171d5b6f6735f5e3dc5b (yeah my own :-/)
introduced a bug in regard to pud/pmd table entries.
If the address of the page table refered to by a pud/pmd value happens
to have zeroes in the lower 32 bits, pud_present and pmd_present return
false. The obvious effect is that this triggers the BUG_ON in exit_mmap
because some ptes will not get released on process end. Worse is that
the next fault for memory covered by that pud/pmd will allocate another
pmd/pte table and populate the pud/pmd entry. The old page table
entries hanging below this entry are lost!
The fix is simple, properly check against 0. The check is added for
pud_none/pmd_none as well even if these two functions work because
the invalid bit is in the lower 32 bits.
Richard Knutsson [Sun, 16 Dec 2007 22:10:33 +0000 (14:10 -0800)]
[IRDA]: irda parameters warning fixes.
This patch fixes:
CHECK /home/kernel/src/net/irda/parameters.c
/home/kernel/src/net/irda/parameters.c:466:2: warning: Using plain integer as NULL pointer
/home/kernel/src/net/irda/parameters.c:520:2: warning: Using plain integer as NULL pointer
/home/kernel/src/net/irda/parameters.c:573:2: warning: Using plain integer as NULL pointer
Hinko Kocevar [Sun, 16 Dec 2007 22:08:58 +0000 (14:08 -0800)]
[IRDA]: irlmp_unregister_link() needs to free lsaps.
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in irlmp_unregister_link(). Hashbin for lsaps is created in
irlmp_register_link and should probably be freed in irlmp_unregister_link().
Oliver Neukum [Sun, 16 Dec 2007 22:07:36 +0000 (14:07 -0800)]
[IRDA]: Race between open and disconnect in irda-usb.
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Vlad Yasevich [Sun, 16 Dec 2007 22:05:45 +0000 (14:05 -0800)]
[SCTP]: Flush fragment queue when exiting partial delivery.
At the end of partial delivery, we may have complete messages
sitting on the fragment queue. These messages are stuck there
until a new fragment arrives. This can comletely stall a
given association. When clearing partial delivery state, flush
any complete messages from the fragment queue and send them on
their way up.
Jarek Poplawski [Sun, 16 Dec 2007 22:02:07 +0000 (14:02 -0800)]
[AX25]: Locking dependencies fix in ax25_disconnect().
Bernard Pidoux reported these lockdep warnings:
[ INFO: possible irq lock inversion dependency detected ]
2.6.23.1 #1
---------------------------------------------------------
fpac/4933 just changed the state of lock:
(slock-AF_AX25){--..}, at: [<d8be3312>] ax25_disconnect+0x46/0xaf
[ax25]
but this lock was taken by another, soft-irq-safe lock in the past:
(ax25_list_lock){-+..}
and interrupts could create inverse lock ordering between them.
[...]
This means slock-AF_AX25 could be taken both from softirq and process
context with softirqs enabled, so it's endangered itself, but also makes
ax25_list_lock vulnerable. It was not 100% verified if the real lockup
can happen, but this fix isn't very costly and looks safe anyway.
(It was tested by Bernard with 2.6.23.9 and 2.6.24-rc5 kernels.)
Wei Yongjun [Sun, 16 Dec 2007 21:39:57 +0000 (13:39 -0800)]
[IPV6]: Fix the return value of ipv6_getsockopt
If CONFIG_NETFILTER if not selected when compile the kernel source code,
ipv6_getsockopt will returen an EINVAL error if optname is not supported by
the kernel. But if CONFIG_NETFILTER is selected, ENOPROTOOPT error will
be return.
This patch fix to always return ENOPROTOOPT error if optname argument of
ipv6_getsockopt is not supported by the kernel.
Assigning a valid random address to bridge device solves problems
when bridge device is brought up before adding real device to bridge.
When the first real device is added to the bridge, it's address
will overide the bridges random address.
Note: any device added to a bridge must already have a valid
ethernet address.
br_add_if -> br_fdb_insert -> fdb_insert -> is_valid_ether_addr
Amos Waterland [Fri, 14 Dec 2007 19:30:22 +0000 (11:30 -0800)]
[IPV4]: Updates to nfsroot documentation
The difference between ip=off and ip=::::::off has been a cause of much
confusion. Document how each behaves, and do not contradict ourselves by
saying that "off" is the default when in fact "any" is the default and is
descibed as being so lower in the file.
[ATM]: Fix compiler warning noise with FORE200E driver
gcc throws these warnings with:
CONFIG_ATM_FORE200E=m
# CONFIG_ATM_FORE200E_PCA is not set
drivers/atm/fore200e.c:2695: warning: 'fore200e_pca_detect' defined but
not used
drivers/atm/fore200e.c:2748: warning: 'fore200e_pca_remove_one' defined
but not used
By moving the #ifdef CONFIG_ATM_FORE200E_PCA around those two functions,
the compiler warnings are silenced.
Patrick McHardy [Thu, 13 Dec 2007 17:32:04 +0000 (09:32 -0800)]
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
As reported by Damien Thebault, the double POSTROUTING hook invocation
fix caused outgoing packets routed between two bridges to appear without
a link-layer header. The reason for this is that we're skipping the
br_nf_post_routing hook for routed packets now and don't save the
original link layer header, but nevertheless tries to restore it on
output, causing corruption.
The root cause for this is that skb->nf_bridge has no clearly defined
lifetime and is used to indicate all kind of things, but that is
quite complicated to fix. For now simply don't touch these packets
and handle them like packets from any other device.
Andrew Morton [Wed, 12 Dec 2007 19:24:19 +0000 (11:24 -0800)]
[TIPC]: Fix semaphore handling.
As noted by Kevin, tipc's release() does down_interruptible() and
ignores the return value. So if signal_pending() we'll end up doing
up() on a non-downed semaphore. Fix.
Paul Moore [Wed, 12 Dec 2007 19:10:16 +0000 (11:10 -0800)]
[XFRM]: Display the audited SPI value in host byte order.
Currently the IPsec protocol SPI values are written to the audit log in
network byte order which is different from almost all other values which
are recorded in host byte order. This patch corrects this inconsistency
by writing the SPI values to the audit record in host byte order.
Patrick McHardy [Wed, 12 Dec 2007 18:35:16 +0000 (10:35 -0800)]
[NETFILTER]: ip_tables: fix compat copy race
When copying entries to user, the kernel makes two passes through the
data, first copying all the entries, then fixing up names and counters.
On the second pass it copies the kernel and match data from userspace
to the kernel again to find the corresponding structures, expecting
that kernel pointers contained in the data are still valid.
This is obviously broken, fix by avoiding the second pass completely
and fixing names and counters while dumping the ruleset, using the
kernel-internal data structures.
Al Viro [Mon, 10 Dec 2007 18:39:29 +0000 (18:39 +0000)]
hamachi endianness fixes
badly broken on big-endian
* passing little-endian to pci_unmap_single() et.al.
* cpu_to_le32() before passing value to writel()
* worse, cpu_to_le64() and shifting/masking result before the same
* hmp->tx_ring[i].status_n_length = cpu_to_le32(
DescEndRing |
(hmp->tx_ring[i].status_n_length & 0x0000FFFF));
is obviously bogus on big-endian. Not hard to untangle, fortunately...
* poisoning addresses in rx_ring is better done after we'd done
pci_unmap_single() on them, not before that. [this one affects little-endian
as well, obviously, provided that pci_unmap_single() is not a no-op on target
in question]
Al Viro [Sun, 9 Dec 2007 17:00:54 +0000 (17:00 +0000)]
starfire VLAN fix
Recognized VLAN ids are set via writew(), should go in host-endian.
That's a long-standing bug, BTW - see http://lkml.org/lkml/2004/2/27/180
for example. What happens is that card gets VLAN id table populated by
byteswapped values on little-endian boxen (so 257 works as expected, 256
and 258 do not, etc.). Bug is easily reproduced, patch fixes it.
Al Viro [Sun, 9 Dec 2007 16:50:47 +0000 (16:50 +0000)]
sundance fixes
* all places where we assign ->addr get cpu_to_le32(pci_map_single(....)), so
we ought to convert back to host-endian before doing pci_unmap_single() et.al.
* poisoning addresses in netdev_close() should be done _after_ unmapping them,
not before it...
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Martin Habets [Fri, 14 Dec 2007 18:59:50 +0000 (10:59 -0800)]
[SPARC32]: Silence sparc32 warnings on missing syscalls.
Silence sparc32 warnings on missing syscalls, these won't be added.
This patch is based on this mail:
http://www.mail-archive.com/[email protected]/msg02571.html
> In linux-2.6.24-rc4 the Toshiba RBTX4927 hangs on boot.
>
> The cause is that plat_time_init() from arch/mips/tx4927/common/
> tx4927_setup.c does not override the __weak plat_time_init() from
> arch/mips/kernel/time.c. This is due to a compiler bug in gcc 4.1.1. The
> bug is reported to not exist in earlier versions of gcc, and to be fixed in
> 4.1.2. The problem is that the __weak plat_time_init() is empty and thus
> gets optimized out of existence (thus the linker is never given the option
> to replace the __weak function).
[ He meant the call to plat_time_init() from time_init() gets optimized away ]
> For more info on the gcc bug see
>
> http://gcc.gnu.org/bugzilla/show_bug.cgi?id=27781
>
> The attached patch is one workaround. Another possible workaround
[ His patch adds -fno-unit-at-a-time for time.c ]
> would be to change the __weak plat_time_init() to be a non-empty
> function.
The __weak definition of plat_time_init was only ever meant to be a
migration helper to keep platforms that don't have a plat_time_init
compiling. A few greps says that all platforms now supply their own
plat_time_init() so the weak definition is no longer needed. So I
instead delete it.
Ralf Baechle [Tue, 11 Dec 2007 19:49:24 +0000 (19:49 +0000)]
[MIPS] PCI: Make pcibios_fixup_device_resources ignore legacy resources.
There might be other reasons why a resource might be marked as fixed
such as a PCI UART holding the system console but until we use
IORESOURCE_PCI_FIXED that way also this will work.
Sergei Shtylyov [Mon, 10 Dec 2007 17:36:50 +0000 (20:36 +0300)]
[MIPS] Alchemy: fix off by two error in __fixup_bigphys_addr()
the PCI specific code in this function doesn't check for the address range
being under the upper bound of the PCI memory window correctly -- fix this,
somewhat beautifying the code around the check, while at it...
Sergei Shtylyov [Mon, 10 Dec 2007 17:28:51 +0000 (20:28 +0300)]
[MIPS] Alchemy: fix PCI resource conflict
... by getting the PCI resources back into the 32-bit range -- there's no
need therefore for CONFIG_RESOURCES_64BIT either. This makes Alchemy PCI
work again while currently the kernel skips the bus scan.
Michael Ellerman [Mon, 10 Dec 2007 04:17:43 +0000 (15:17 +1100)]
[POWERPC] Make PS3_SYS_MANAGER default y, not m
Currently it's impossible to build a ps3_defconfig which will reboot
without modules installed. This makes it all too easy to find yourself
with a PS3 that won't reboot.
This is because the system manager driver, which provides the reboot
mechanism, is only selectable if PS3_ADVANCED is set, else it defaults
to m. In ps3_defconfig PS3_ADVANCED is not set, therefore the system
manager is built as a module.
It would be desirable IMHO for the defconfig to produce a kernel that
boots and reboots, without needing modules to be installed.
Liu Yu [Mon, 10 Dec 2007 05:00:52 +0000 (13:00 +0800)]
[POWERPC] Fix rounding bug in emulation for double float operating
This patch fixes rounding bug in emulation for double float operating on PowerPC platform.
When pack double float operand, it need to truncate the tail due to the limited precision.
If the truncated part is not zero, the last bit of work bit (totally 3 bits) need to '|' 1.
This patch is completed in _FP_FRAC_SRS_2(X,N,sz) (arch/powerpc/math-emu/op-2.h).
Originally the code leftwards rotates the operand to just keep the truncated part,
then check whether it is zero. However, the number it rotates is not correct when
N is not smaller than _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the improper case.
Stephen Rothwell [Wed, 12 Dec 2007 03:58:12 +0000 (14:58 +1100)]
[POWERPC] iSeries: don't printk with HV spinlock held
Printk was observed to hang during module unload due to a limited
window of characters that may be sent to the hypervisor. The window
only reexpands when we receive an ack from the HV and the spinlock here
prevents us from ever processing that ack. This fixes it by dropping
the lock before doing the printk, then looping back to the top to
reacquire the lock.
Jochen Friedrich [Thu, 22 Nov 2007 16:53:54 +0000 (17:53 +0100)]
[POWERPC] Kill non-existent symbols from ksyms and commproc.h
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
ACPI: thinkpad-acpi: fix lenovo keymap for brightness
Starting in 2.6.23...
Several reports from X60 users complained that the default Lenovo keymap
issuing EV_KEY KEY_BRIGHTNESS_UP/DOWN input events caused major issues when
the proper brightness support through ACPI video.c was loaded.
Therefore, remove the generation of these events by default, which is the
right thing for T60, X60, R60, T61, X61 and R61 with their latest BIOSes.
Distros that want to misuse these events into OSD reporting (which requires
an ugly hack from hell in HAL) are welcome to set up the key map they need
through HAL. That way, we don't break everyone else's systems.
The ->cap fields of struct acpi_video_device and struct acpi_video_bus
are 1B each, not 4B. The oversized memset()'s corrupted the subsequent
list_head fields. This resulted in silent corruption without
CONFIG_DEBUG_LIST and BUG's with it. This patch uses sizeof() to pass
the proper bounds to the memset() calls and thereby correct the bugs.
kbuild: re-enable Makefile generation in a new O=... directory
The commit: 18c32dac75b187d1a4e858f3cfdf03e844129f5e "kbuild: fix
building with O=.. options"
disabled the creation of a Makefile in a new O=... directory. Restore it.
David S. Miller [Thu, 13 Dec 2007 14:13:38 +0000 (06:13 -0800)]
[SPARC64]: Fix two kernel linear mapping setup bugs.
This was caught and identified by Greg Onufer.
Since we setup the 256M/4M bitmap table after taking over the trap
table, it's possible for some 4M mapping to get loaded in the TLB
beforhand which later will be 256M mappings.
This can cause illegal TLB multiple-match conditions. Fix this by
setting up the bitmap before we take over the trap table.
Next, __flush_tlb_all() was not doing anything on hypervisor
platforms. Fix by adding sun4v_mmu_demap_all() and calling it.
Adrian Bunk [Wed, 12 Dec 2007 19:44:54 +0000 (16:44 -0300)]
V4L/DVB (6803): buf-core.c locking fixes
After commit 19fb1457990b6b7e15586ec7331541a184233acc the callers in
videobuf-core.c that already hold the lock must call
__videobuf_read_start() instead of videobuf_read_start().
Trond Myklebust [Thu, 13 Dec 2007 01:16:06 +0000 (20:16 -0500)]
MAINTAINERS: update the NFS CLIENT entry
Add in the new NFS mailing list on vger, website, and git tree info, and
update my email address to reflect the fact that I've been working for
netapp for the past 2 years.
projects / linux.git / log