Lin Ming [Thu, 13 Sep 2012 22:26:33 +0000 (00:26 +0200)]
ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
Commit 0090def("ACPI: Add interface to register/unregister device
to/from power resources") used resource_lock to protect the devices list
that relies on power resource. It caused a mutex dead lock, as below
This patch adds a new mutex "devices_lock" to protect the devices list
and calls acpi_power_on_device in acpi_power_on, instead of
__acpi_power_on, after the resource_lock is released.
[rjw: Changed data type of a boolean variable to bool.]
ACPI / PM: Infer parent power state from child if unknown, v2
It turns out that there are ACPI BIOSes defining device objects with
_PSx and without either _PSC or _PRx. For devices corresponding to
those ACPI objetcs __acpi_bus_get_power() returns ACPI_STATE_UNKNOWN
and their initial power states are regarded as unknown as a result.
If such a device is a parent of another power-manageable device, the
child cannot be put into a low-power state through ACPI, because
__acpi_bus_set_power() refuses to change power states of devices
whose parents' power states are unknown.
To work around this problem, observe that the ACPI power state of
a device cannot be higher-power (lower-number) than the power state
of its parent. Thus, if the device's _PSC method or the
configuration of its power resources indicates that the device is
in D0, the device's parent has to be in D0 as well. Consequently,
if the parent's power state is unknown when we've just learned that
its child's power state is D0, we can safely set the parent's
power.state field to ACPI_STATE_D0.
pktgen: fix crash with vlan and packet size less than 46
If vlan option is being specified in the pktgen and packet size
being requested is less than 46 bytes, despite being illogical
request, pktgen should not crash the kernel.
The root cause of why pktgen is not able to handle this case is due
to comparison of signed (datalen) and unsigned data (sizeof), which
eventually passes a huge number to skb_put().
Dan Carpenter [Sat, 1 Sep 2012 19:54:07 +0000 (12:54 -0700)]
thinkpad_acpi: buffer overflow in fan_get_status()
The acpi_evalf() function modifies four bytes of data but in
fan_get_status() we pass a pointer to u8. I have modified the
function to use type checking now.
Bernhard Froemel [Sat, 25 Aug 2012 08:30:48 +0000 (10:30 +0200)]
apple-gmux: Fix index read functions
Study of Apple's binary driver revealed that the GMUX_READ_PORT should
be written between calls to gmux_index_wait_ready and
gmux_index_wait_complete (i.e., the new index protocol must be
followed). If this is not done correctly, the indexed
gmux device only partially accepts writes which lead to problems
concerning GPU switching. Special thanks to Seth Forshee who helped
greatly with identifying unnecessary changes.
Commit a334872224a67b614dc888460377862621f3dac7 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
bnx2x: correct advertisement of pause capabilities
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Christian König [Thu, 13 Sep 2012 08:33:47 +0000 (10:33 +0200)]
drm/radeon: make 64bit fences more robust v3
Only increase the higher 32bits if we really detect a wrap around.
v2: instead of increasing the higher 32bits just use the higher
32bits from the last emitted fence.
v3: also use last emitted fence value as upper limit.
The intention of this patch is to make fences as robust as
they where before introducing 64bit fences. This is
necessary because on older systems it looks like the fence
value gets corrupted on initialization.
Should also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=54129
https://bugs.freedesktop.org/show_bug.cgi?id=54662
https://bugzilla.redhat.com/show_bug.cgi?id=846505
https://bugzilla.redhat.com/show_bug.cgi?id=845639
3.5 needs a separate patch due to changes in the
fence code. Will send that out separately.
Alex Deucher [Fri, 31 Aug 2012 15:56:50 +0000 (11:56 -0400)]
drm/radeon: rework pll selection (v3)
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
net: qmi_wwan: call subdriver with control intf only
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
David Ward [Thu, 13 Sep 2012 05:22:35 +0000 (05:22 +0000)]
net_sched: gred: actually perform idling in WRED mode
gred_dequeue() and gred_drop() do not seem to get called when the
queue is empty, meaning that we never start idling while in WRED
mode. And since qidlestart is not stored by gred_store_wred_set(),
we would never stop idling while in WRED mode if we ever started.
This messes up the average queue size calculation that influences
packet marking/dropping behavior.
Now, we start WRED mode idling as we are removing the last packet
from the queue. Also we now actually stop WRED mode idling when we
are enqueuing a packet.
David Ward [Thu, 13 Sep 2012 05:22:34 +0000 (05:22 +0000)]
net_sched: gred: fix qave reporting via netlink
q->vars.qavg is a Wlog scaled value, but q->backlog is not. In order
to pass q->vars.qavg as the backlog value, we need to un-scale it.
Additionally, the qave value returned via netlink should not be Wlog
scaled, so we need to un-scale the result of red_calc_qavg().
This caused artificially high values for "Average Queue" to be shown
by 'tc -s -d qdisc', but did not affect the actual operation of GRED.
mISDN: Fix wrong usage of flush_work_sync while holding locks
It is a bad idea to hold a spinlock and call flush_work_sync.
Move the workqueue cleanup outside the spinlock and use cancel_work_sync,
on closing the channel this seems to be the more correct function.
Remove the never used and constant return value of mISDN_freebchannel.
David S. Miller [Thu, 13 Sep 2012 17:53:06 +0000 (13:53 -0400)]
Merge branch 'master' of git://1984.lsi.us.es/nf
Pablo Neira Ayuso say:
====================
The following patchset contains four updates for your net tree, they are:
* Fix crash on timewait sockets, since the TCP early demux was added,
in nfnetlink_log, from Eric Dumazet.
* Fix broken syslog log-level for xt_LOG and ebt_log since printk format was
converted from <.> to a 2 bytes pattern using ASCII SOH, from Joe Perches.
* Two security fixes for the TCP connection tracking targeting off-path attacks,
from Jozsef Kadlecsik. The problem was discovered by Jan Wrobel and it is
documented in: http://mixedbit.org/reflection_scan/reflection_scan.pdf.
====================
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few small / trivial regression fixes at this time."
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: ice1724: Use linear scale for AK4396 volume control.
ALSA: hda_intel: add position_fix quirk for Asus K53E
ALSA: compress_core: fix open flags test in snd_compr_open()
ALSA: hda - Fix Oops at codec reset/reconfig
ALSA: usb-audio: Fix bogus error messages for delay accounting
ALSA: hda - Fix missing Master volume for STAC9200/925x
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Olof Johansson:
- A set of OMAP fixes, about half of them PM/clock related, the rest
scattered over the platform code but all small and targeted to real
bugs.
- Two small i.MX fixes for SSI device clock setup.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: clk-imx35: Fix SSI clock registration
ARM: clk-imx25: Fix SSI clock registration
ARM: OMAP4: Fix array size for irq_target_cpu
ARM: OMAP4: hwmod data: temporarily comment out data for the sl2if IP block
ARM: OMAP: hwmod code: Disable module when hwmod enable fails
ARM: OMAP3: hwmod data: fix iva2 reset info
ARM: OMAP3xxx: clockdomain: fix software supervised wakeup/sleep
ARM: OMAP2+: am33xx: Fix the timer fck clock naming convention
ARM: OMAP: Config fix for omap3-touchbook board
ARM: OMAP: sram: skip the first 16K on OMAP3 HS
ARM: OMAP: sram: fix OMAP4 errata handling
ARM: OMAP: timer: obey the !CONFIG_OMAP_32K_TIMER
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull additional AHCI PCI IDs from Jeff Garzik.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Add identifiers for ASM106x devices
ahci: Add alternate identifier for the 88SE9172
ahci: Add JMicron 362 device IDs
GFS2: Take account of blockages when using reserved blocks
The claim_reserved_blks() function was not taking account of
the possibility of "blockages" while performing allocation.
This can be caused by another node allocating something in
the same extent which has been reserved locally.
This patch tests for this condition and then skips the remainder
of the reservation in this case. This is a relatively rare event,
so that it should not affect the general performance improvement
which the block reservations provide.
The claim_reserved_blks() function also appears not to be able
to deal with reservations which cross bitmap boundaries, but
that can be dealt with in a future patch since we don't generate
boundary crossing reservations currently.
This collects up the write size hinting code which is used by the
block reservation subsystem into a single function. At the same
time this also corrects the rounding for this calculation.
Dave Airlie [Thu, 13 Sep 2012 04:18:55 +0000 (14:18 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung into drm-fixes
Inki Dae writes:
- fix build warnings
- minor code cleanup
- remove non-standard format, DRM_FORMAT_NV12M
- add dummy mmap for exynos dmabuf
. dma_buf export needs this patch
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm: Drop the NV12M and YUV420M formats
drm/exynos: remove DRM_FORMAT_NV12M from plane module
drm/exynos: fix double call of drm_prime_(init/destroy)_file_private
drm/exynos: add dummy support for dmabuf-mmap
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
drm/exynos: Make g2d_pm_ops static
drm/exynos: Add dependency for G2D in Kconfig
drm/exynos: fixed page align bug.
drm/exynos: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/exynos: Use devm_* functions in exynos_drm_g2d.c file
drm/exynos: Use devm_kzalloc in exynos_drm_hdmi.c file
drm/exynos: Use devm_kzalloc in exynos_drm_vidi.c file
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
drm/exynos: Remove redundant check in exynos_hdmi.c file
drm/exynos: remove DRM_FORMAT_NV12M from plane module
this patch removes DRM_FORMAT_NV12M from plane module because this format
is same as DRM_FORMAT_NV12. DRM_FORMAT_NV12M will be identified by
mode_cmd->handles and mode_cmd->offsets fields internally.
Sachin Kamat [Fri, 31 Aug 2012 10:20:48 +0000 (15:50 +0530)]
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
Fixes the following checkpatch warnings:
WARNING: sizeof filter_y_horiz_tap8 should be sizeof(filter_y_horiz_tap8)
WARNING: sizeof filter_y_vert_tap4 should be sizeof(filter_y_vert_tap4)
WARNING: sizeof filter_cr_horiz_tap4 should be sizeof(filter_cr_horiz_tap4)
Sachin Kamat [Fri, 31 Aug 2012 10:20:47 +0000 (15:50 +0530)]
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
Fixes the following checkpatch warnings:
WARNING: sizeof *res should be sizeof(*res)
WARNING: sizeof res->regul_bulk[0] should be sizeof(res->regul_bulk[0])
WARNING: sizeof *res should be sizeof(*res)
Sachin Kamat [Mon, 6 Aug 2012 06:46:17 +0000 (12:16 +0530)]
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
devm_request_and_ioremap function checks the validity of the
pointer returned by platform_get_resource. Hence an additional check
in the probe function is not necessary.
Sachin Kamat [Mon, 6 Aug 2012 06:46:16 +0000 (12:16 +0530)]
drm/exynos: Remove redundant check in exynos_hdmi.c file
devm_request_and_ioremap function checks the validity of the
pointer returned by platform_get_resource. Hence an additional check
in the probe function is not necessary.
digsig: add hash size comparision on signature verification
When pkcs_1_v1_5_decode_emsa() returns without error and hash sizes do
not match, hash comparision is not done and digsig_verify_rsa() returns
no error. This is a bug and this patch fixes it.
The bug was introduced in v3.3 by commit b35e286a640f ("lib/digsig:
pkcs_1_v1_5_decode_emsa cleanup").
Dave Airlie [Thu, 13 Sep 2012 01:07:31 +0000 (11:07 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
"Nothing really major at all:
- fixup edp setup sequence (Dave)
- disable sdvo hotplug for real, this is a fixup for a messed-up
regression fixer (Jani)
- don't expose dysfunctional backlight driver (Jani)
- properly init spinlock (only used by hsw/vlv code) from Alexander
Shishkin"
along with a couple of more fixes on top.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix up the IBX transcoder B check
drm/i915: set the right gen3 flip_done mode also at resume
drm/i915: initialize dpio_lock spin lock
drm/i915: do not expose a dysfunctional backlight interface to userspace
drm/i915: only enable sdvo hotplug irq if needed
drm/i915/edp: get the panel delay before powering up
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"It's been a while... so there's a little more here than normal.
Mostly updates from Will for the breakpoint stuff, and plugging a few
holes in the user access functions which crept in when domain support
was disabled for ARMv7 CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7529/1: delay: set loops_per_jiffy when moving to timer-based loop
ARM: 7528/1: uaccess: annotate [__]{get,put}_user functions with might_fault()
ARM: 7527/1: uaccess: explicitly check __user pointer when !CPU_USE_DOMAINS
ARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path
ARM: 7521/1: Fix semihosting Kconfig text
ARM: 7513/1: Make sure dtc is built before running it
ARM: 7512/1: Fix XIP build due to PHYS_OFFSET definition moving
ARM: 7499/1: mm: Fix vmalloc overlap check for !HIGHMEM
ARM: 7503/1: mm: only flush both pmd entries for classic MMU
ARM: 7502/1: contextidr: avoid using bfi instruction during notifier
ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores
ARM: 7497/1: hw_breakpoint: allow single-byte watchpoints on all addresses
ARM: 7496/1: hw_breakpoint: don't rely on dfsr to show watchpoint access type
ARM: Fix ioremap() of address zero
Merge tag 'nfs-for-3.6-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Final (hopefully) fix for the range checking code in NFSv4 getacl.
This should fix the Oopses being seen when the acl size is close to
PAGE_SIZE.
- Fix a regression with the legacy binary mount code
- Fix a regression in the readdir cookieverf initialisation
- Fix an RPC over UDP regression
- Ensure that we report all errors in the NFSv4 open code
- Ensure that fsync() reports all relevant synchronisation errors.
* tag 'nfs-for-3.6-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: fsync() must exit with an error if page writeback failed
SUNRPC: Fix a UDP transport regression
NFS: return error from decode_getfh in decode open
NFSv4: Fix buffer overflow checking in __nfs4_get_acl_uncached
NFSv4: Fix range checking in __nfs4_get_acl_uncached and __nfs4_proc_set_acl
NFS: Fix a problem with the legacy binary mount code
NFS: Fix the initialisation of the readdir 'cookieverf' array
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
When attaching an imx28 or imx53 in USB gadget mode to a Windows host and
starting a rndis connection we see this message every 4-10 seconds:
g_ether gadget: high speed config #2: RNDIS
Analysis shows that each time this message is printed, the rndis connection is
re-establish due to a reset because of a stalled endpoint (ep 0, dir 1). The
endpoint is stalled because the reqeust complete bit on that endpoint is set,
but in isr_tr_complete_low() the endpoint request list (mEp->qh.queue) is
empty.
This patch removed this check, because the code doesn't take the following
situation into account:
The loop over all endpoints in isr_tr_complete_handler() will call ep_nuke() on
both ep0/dir0 and ep/dir1 in the first loop. Pending reqeusts will be flushed
and completed here. There seems to be a race condition, the request is nuked,
but the request complete bit will be set, too. The subsequent check (in
ep0/dir1's loop cycle) for endpoint request list (mEp->qh.queue) empty will
fail.
Both other mainline chipidea drivers (mv_udc_core.c and fsl_udc_core.c) don't
have this check.
usb: chipidea: cleanup dma_pool if udc_start() fails
If udc_start() fails the qh_pool dma-pool cannot be closed because
it's still in use. This patch factors out the dma_pool_free() loop
into destroy_eps() and calls it in the error path of udc_start(),
too.
usb: chipidea: udc: fix setup of endpoint maxpacket size
This patch changes the setup of the endpoint maxpacket size. All non control
endpoints are initialized with an undefined ((unsigned short)~0) maxpacket
size. The maxpacket size of Endpoint 0 will be kept at CTRL_PAYLOAD_MAX.
Some gadget drivers check for the maxpacket size before they enable the
endpoint, which leads to a wrong state in these drivers.
Shlomo Pongratz [Wed, 29 Aug 2012 15:14:34 +0000 (15:14 +0000)]
IPoIB: Fix AB-BA deadlock when deleting neighbours
Lockdep points out a circular locking dependency betwwen the ipoib
device priv spinlock (priv->lock) and the neighbour table rwlock
(ntbl->rwlock).
In the normal path, ie neigbour garbage collection task, the neigh
table rwlock is taken first and then if the neighbour needs to be
deleted, priv->lock is taken.
However in some error paths, such as in ipoib_cm_handle_tx_wc(),
priv->lock is taken first and then ipoib_neigh_free routine is called
which in turn takes the neighbour table ntbl->rwlock.
The solution is to get rid the neigh table rwlock completely and use
only priv->lock.
Shlomo Pongratz [Wed, 29 Aug 2012 15:14:33 +0000 (15:14 +0000)]
IPoIB: Fix memory leak in the neigh table deletion flow
If the neighbours hash table is empty when unloading the module, then
ipoib_flush_neighs(), the cleanup routine, isn't called and the
memory used for the hash table itself leaked.
To fix this, ipoib_flush_neighs() is allways called, and another
completion object is added to signal when the table is freed.
Once invoked, ipoib_flush_neighs() flushes all the neighbours (if
there are any), calls the the hash table RCU free routine, which now
signals completion of the deletion process, and waits for the last
neighbour to be freed.
Wolfram Sang [Sat, 8 Sep 2012 15:28:06 +0000 (17:28 +0200)]
i2c: mxs: correctly setup speed for non devicetree
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.
Roland Stigge [Wed, 8 Aug 2012 07:42:32 +0000 (09:42 +0200)]
i2c: pnx: Fix read transactions of >= 2 bytes
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:
Dummy-TX - RX - Dummy-TX - RX - ...
But since RFE actually stays high after some Dummy-TX, it rather looks like:
Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)
The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.
This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.
result with linux 3.6-rc5
Sep 12 06:37:29 xxxxx kernel: <5>DENY in: IN=eth0 OUT= MAC=.......
result with linux 3.5.3 and older:
Sep 9 10:43:01 xxxxx kernel: DENY in: IN=eth0 OUT= MAC......
commit 04d2c8c83d0
("printk: convert the format for KERN_<LEVEL> to a 2 byte pattern")
updated the syslog header style but did not update netfilter uses.
Do so.
Use KERN_SOH and string concatenation instead of "%c" KERN_SOH_ASCII
as suggested by Eric Dumazet.
ALSA: ice1724: Use linear scale for AK4396 volume control.
The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right. This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.
hwmon: (ina2xx) Fix word size register read and write operations
The driver uses be16_to_cpu and cpu_to_be16 to convert data in SMBus word
operations from chip to host byte order. However, the data passed from and to
the SMBus word API functions is in host byte order, not in chip byte order.
Conversion should therefore use swab16 instead of be16 to change the byte order.
Replace driver internal word conversion functions with SMBus API functions to
solve the problem.
dma_alloc/free_coherent APIs requires the platform specific remoteproc
device as the device parameter. We are passing vdev->dev.parent to the
dma_free_coherent function which is the generic rproc device and it is
wrong, it has to be vdev->dev.parent->parent instead, same as when we
call dma_alloc_coherent function.
Merge branch 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"It's later than I'd like but well the timing just didn't work out this
time.
There are three bug fixes. One from before 3.6-rc1 and two from the
new CPU hotplug code. Kudos to Lai for discovering all of them and
providing fixes.
* Atomicity bug when clearing a flag and setting another. The two
operation should have been atomic but wasn't. This bug has existed
for a long time but is unlikely to have actually happened. Fix is
safe. Marked for -stable.
* If CPU hotplug cycles happen back-to-back before workers finish the
previous cycle, the states could get out of sync and it could get
stuck. Fixed by waiting for workers to complete before finishing
hotplug cycle.
* While CPU hotplug is in progress, idle workers could be depleted
which can then lead to deadlock. I think both happening together
is highly unlikely but still better to fix it and the fix isn't too
scary.
There's another workqueue related regression which reported a few days
ago:
https://bugzilla.kernel.org/show_bug.cgi?id=47301
It's a bit of head scratcher but there is a semi-reliable reproduce
case, so I'm hoping to resolve it soonish."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix possible idle worker depletion across CPU hotplug
workqueue: restore POOL_MANAGING_WORKERS
workqueue: fix possible deadlock in idle worker rebinding
workqueue: move WORKER_REBIND clearing in rebind_workers() to the end of the function
workqueue: UNBOUND -> REBIND morphing in rebind_workers() should be atomic
Pull crypto fixes from Herbert Xu:
"This fixes the authenc self-test crash as well as a missing export of
a symbol used by a module."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: authenc - Fix crash with zero-length assoc data
crypto/caam: Export gen_split_key symbol for other modules
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
Pull blackfin updates from Bob Liu:
"One kbuild and a smp build fix."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
kbuild: add symbol prefix arg to kallsyms
blackfin: smp: adapt to generic smp helpers
added a device specific entry assuming that the device would use
class/subclass/proto == ff/ff/ff like other ZTE devices. It
turns out that ZTE has started using vendor specific subclass
and protocol codes:
We do not have any information on how ZTE intend to use these
codes, but let us assume for now that the 3 sets matching
serial functions in the K5006-Z always will identify a serial
function in a ZTE device.
drm/i915: assert that the IBX port transcoder select w/a is implemented
Unfortunately I've failed to notice that these checks are not just
called for the port that is about to be disabled, but for all (which
makes sense for an assert ...), and the WARN missfired when disabling
another pipe than the one with the dp port.
Hence also check whether the port is actually disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54688 Reviewed-by: Paulo Zanoni <[email protected]> Signed-Off-by: Daniel Vetter <[email protected]>
ALSA: hda_intel: add position_fix quirk for Asus K53E
Commit c20c5a841cbe47f5b7812b57bd25397497e5fbc0 changed some chipsets to
default to POS_FIX_COMBO so they now use POS_FIX_LPIB instead of
POS_FIX_POSBUF. Since then I've been getting artifacts on playback, including
repeated sounds on my Asus laptop.
My hardware is Cougar Point which the commit log of c20c5a841cbe47f5b7812b57bd25397497e5fbc0 mentions as tested so POS_FIX_COMBO
probably works in general but apparently it doesn't on Asus K53E therefore the
need for the quirk.
Dan Carpenter [Tue, 11 Sep 2012 11:12:43 +0000 (14:12 +0300)]
ALSA: compress_core: fix open flags test in snd_compr_open()
O_RDONLY is zero so the original test (f->f_flags & O_RDONLY) is always
false and it will never do compress capture. The test for O_WRONLY is
also slightly off. The original test would consider "->flags =
(O_WRONLY | O_RDWR)" as write only instead of rejecting it as invalid.
I've also removed the pr_err() because that could flood dmesg.
Herbert Xu [Tue, 11 Sep 2012 04:05:45 +0000 (12:05 +0800)]
crypto: authenc - Fix crash with zero-length assoc data
The authenc code doesn't deal with zero-length associated data
correctly and ends up constructing a zero-length sg entry which
causes a crash when it's fed into the crypto system.
This patch fixes this by avoiding the code-path that triggers
the SG construction if we have no associated data.
This isn't the most optimal fix as it means that we'll end up
using the fallback code-path even when we could still execute
the digest function. However, this isn't a big deal as nobody
but the test path would supply zero-length associated data.
James Hogan [Thu, 6 Sep 2012 21:11:25 +0000 (22:11 +0100)]
kbuild: add symbol prefix arg to kallsyms
Commit 1f2bfbd00e466ff3489b2ca5cc75b1cccd14c123 ("kbuild: link of
vmlinux moved to a script") introduced in v3.5-rc1 broke kallsyms on
architectures which have symbol prefixes.
The --symbol-prefix argument used to be added to the KALLSYMS command
line from the architecture Makefile, however this isn't picked up by the
new scripts/link-vmlinux.sh. This resulted in symbols like
kallsyms_addresses being added which weren't correctly overriding the
weak symbols such as _kallsyms_addresses. These could then trigger
BUG_ONs in kallsyms code.
This is fixed by removing the KALLSYMS addition from the architecture
Makefile, and using CONFIG_SYMBOL_PREFIX in the link-vmlinux.sh script
to determine whether to add the --symbol-prefix argument.
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"I had actually prepared this fix set before I left for KS + Plumbers,
so it's been incubating much longer than it should have. I'll be
picking up my three week backlog this week, so more fixes will then be
forthcoming
This set consist of three minor and one fairly major (the device not
ready causing offlining problem which is a serious regression
introduced by the media change update) fixes.
Signed-off-by: James Bottomley <[email protected]>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix 'Device not ready' issue on mpt2sas
[SCSI] scsi_lib: fix scsi_io_completion's SG_IO error propagation
[SCSI] megaraid_sas: Move poll_aen_lock initializer
[SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value
Merge tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"A trio of KVM fixes: incorrect lookup of guest cpuid, an uninitialized
variable fix, and error path cleanup fix."
* tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: fix error paths for failed gfn_to_page() calls
KVM: x86: Check INVPCID feature bit in EBX of leaf 7
KVM: PIC: fix use of uninitialised variable.
projects / linux.git / log