Jeremy Cline [Mon, 9 Oct 2023 20:00:54 +0000 (16:00 -0400)]
nfc: nci: assert requested protocol is valid
The protocol is used in a bit mask to determine if the protocol is
supported. Assert the provided protocol is less than the maximum
defined so it doesn't potentially perform a shift-out-of-bounds and
provide a clearer error for undefined protocols vs unsupported ones.
af_packet: Fix fortified memcpy() without flex array.
Sergei Trofimovich reported a regression [0] caused by commit a0ade8404c3b
("af_packet: Fix warning of fortified memcpy() in packet_getname().").
It introduced a flex array sll_addr_flex in struct sockaddr_ll as a
union-ed member with sll_addr to work around the fortified memcpy() check.
However, a userspace program uses a struct that has struct sockaddr_ll in
the middle, where a flex array is illegal to exist.
include/linux/if_packet.h:24:17: error: flexible array member 'sockaddr_ll::<unnamed union>::<unnamed struct>::sll_addr_flex' not at end of 'struct packet_info_t'
24 | __DECLARE_FLEX_ARRAY(unsigned char, sll_addr_flex);
| ^~~~~~~~~~~~~~~~~~~~
To fix the regression, let's go back to the first attempt [1] telling
memcpy() the actual size of the array.
Jakub Kicinski [Tue, 10 Oct 2023 17:36:51 +0000 (10:36 -0700)]
net: tcp: fix crashes trying to free half-baked MTU probes
tcp_stream_alloc_skb() initializes the skb to use tcp_tsorted_anchor
which is a union with the destructor. We need to clean that
TCP-iness up before freeing.
Jakub Kicinski [Thu, 12 Oct 2023 00:22:15 +0000 (17:22 -0700)]
Merge tag 'ieee802154-for-net-2023-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2023-10-10
Just one small fix this time around.
Dinghao Liu fixed a potential use-after-free in the ca8210 driver probe
function.
* tag 'ieee802154-for-net-2023-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wpan/wpan:
ieee802154: ca8210: Fix a potential UAF in ca8210_probe
====================
Nils Hoppmann [Mon, 9 Oct 2023 14:40:48 +0000 (16:40 +0200)]
net/smc: Fix pos miscalculation in statistics
SMC_STAT_PAYLOAD_SUB(_smc_stats, _tech, key, _len, _rc) will calculate
wrong bucket positions for payloads of exactly 4096 bytes and
(1 << (m + 12)) bytes, with m == SMC_BUF_MAX - 1.
Intended bucket distribution:
Assume l == size of payload, m == SMC_BUF_MAX - 1.
Bucket 0 : 0 < l <= 2^13
Bucket n, 1 <= n <= m-1 : 2^(n+12) < l <= 2^(n+13)
Bucket m : l > 2^(m+12)
Current solution:
_pos = fls64((l) >> 13)
[...]
_pos = (_pos < m) ? ((l == 1 << (_pos + 12)) ? _pos - 1 : _pos) : m
For l == 4096, _pos == -1, but should be _pos == 0.
For l == (1 << (m + 12)), _pos == m, but should be _pos == m - 1.
In order to avoid special treatment of these corner cases, the
calculation is adjusted. The new solution first subtracts the length by
one, and then calculates the correct bucket by shifting accordingly,
i.e. _pos = fls64((l - 1) >> 13), l > 0.
This not only fixes the issues named above, but also makes the whole
bucket assignment easier to follow.
Same is done for SMC_STAT_RMB_SIZE_SUB(_smc_stats, _tech, k, _len),
where the calculation of the bucket position is similar to the one
named above.
When the execution order is (1)->(2)->(3), it will crash. Therefore, in
the function nfp_fl_ct_del_flow, nf_flow_table_offload_del_cb needs to
be executed synchronously.
At the same time, in order to solve the deadlock problem and the problem
of rtnl_lock sometimes failing, replace rtnl_lock with the private
nfp_fl_lock.
Javier Carrasco [Mon, 9 Oct 2023 22:26:14 +0000 (00:26 +0200)]
net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read
syzbot has found an uninit-value bug triggered by the dm9601 driver [1].
This error happens because the variable res is not updated if the call
to dm_read_shared_word returns an error. In this particular case -EPROTO
was returned and res stayed uninitialized.
This can be avoided by checking the return value of dm_read_shared_word
and propagating the error if the read operation failed.
Jakub Kicinski [Wed, 11 Oct 2023 02:59:49 +0000 (19:59 -0700)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-10-11
We've added 14 non-merge commits during the last 5 day(s) which contain
a total of 12 files changed, 398 insertions(+), 104 deletions(-).
The main changes are:
1) Fix s390 JIT backchain issues in the trampoline code generation which
previously clobbered the caller's backchain, from Ilya Leoshkevich.
2) Fix zero-size allocation warning in xsk sockets when the configured
ring size was close to SIZE_MAX, from Andrew Kanner.
3) Fixes for bpf_mprog API that were found when implementing support
in the ebpf-go library along with selftests, from Daniel Borkmann
and Lorenz Bauer.
4) Fix riscv JIT to properly sign-extend the return register in programs.
This fixes various test_progs selftests on riscv, from Björn Töpel.
5) Fix verifier log for async callback return values where the allowed
range was displayed incorrectly, from David Vernet.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
s390/bpf: Fix unwinding past the trampoline
s390/bpf: Fix clobbering the caller's backchain in the trampoline
selftests/bpf: Add testcase for async callback return value failure
bpf: Fix verifier log for async callback return values
xdp: Fix zero-size allocation warning in xskq_create()
riscv, bpf: Track both a0 (RISC-V ABI) and a5 (BPF) return values
riscv, bpf: Sign-extend return values
selftests/bpf: Make seen_tc* variable tests more robust
selftests/bpf: Test query on empty mprog and pass revision into attach
selftests/bpf: Adapt assert_mprog_count to always expect 0 count
selftests/bpf: Test bpf_mprog query API via libbpf and raw syscall
bpf: Refuse unused attributes in bpf_prog_{attach,detach}
bpf: Handle bpf_mprog_query with NULL entry
bpf: Fix BPF_PROG_QUERY last field check
====================
Kory Maincent [Mon, 9 Oct 2023 13:36:45 +0000 (15:36 +0200)]
ethtool: Fix mod state of verbose no_mask bitset
A bitset without mask in a _SET request means we want exactly the bits in
the bitset to be set. This works correctly for compact format but when
verbose format is parsed, ethnl_update_bitset32_verbose() only sets the
bits present in the request bitset but does not clear the rest. The commit 6699170376ab fixes this issue by clearing the whole target bitmap before we
start iterating. The solution proposed brought an issue with the behavior
of the mod variable. As the bitset is always cleared the old val will
always differ to the new val.
Fix it by adding a new temporary variable which save the state of the old
bitmap.
Jakub Kicinski [Wed, 11 Oct 2023 02:45:59 +0000 (19:45 -0700)]
Merge tag 'linux-can-fixes-for-6.6-20231009' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2023-10-09
Lukas Magel's patch for the CAN ISO-TP protocol fixes the TX state
detection and wait behavior.
John Watts contributes a patch to only show the sun4i_can Kconfig
option on ARCH_SUNXI.
A patch by Miquel Raynal fixes the soft-reset workaround for Renesas
SoCs in the sja1000 driver.
Markus Schneider-Pargmann's patch for the tcan4x5x m_can glue driver
fixes the id2 register for the tcan4553.
2 patches by Haibo Chen fix the flexcan stop mode for the imx93 SoC.
* tag 'linux-can-fixes-for-6.6-20231009' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: tcan4x5x: Fix id2_register for tcan4553
can: flexcan: remove the auto stop mode for IMX93
can: sja1000: Always restart the Tx queue after an overrun
arm64: dts: imx93: add the Flex-CAN stop mode by GPR
can: sun4i_can: Only show Kconfig if ARCH_SUNXI is set
can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior
====================
Jeremy Kerr [Mon, 9 Oct 2023 07:56:45 +0000 (15:56 +0800)]
mctp: perform route lookups under a RCU read-side lock
Our current route lookups (mctp_route_lookup and mctp_route_lookup_null)
traverse the net's route list without the RCU read lock held. This means
the route lookup is subject to preemption, resulting in an potential
grace period expiry, and so an eventual kfree() while we still have the
route pointer.
Add the proper read-side critical section locks around the route
lookups, preventing premption and a possible parallel kfree.
The remaining net->mctp.routes accesses are already under a
rcu_read_lock, or protected by the RTNL for updates.
Based on an analysis from Sili Luo <[email protected]>, where
introducing a delay in the route lookup could cause a UAF on
simultaneous sendmsg() and route deletion.
Ilya Leoshkevich [Tue, 10 Oct 2023 20:20:10 +0000 (22:20 +0200)]
s390/bpf: Fix unwinding past the trampoline
When functions called by the trampoline panic, the backtrace that is
printed stops at the trampoline, because the trampoline does not store
its caller's frame address (backchain) on stack; it also stores the
return address at a wrong location.
Store both the same way as is already done for the regular eBPF programs.
Ilya Leoshkevich [Tue, 10 Oct 2023 20:20:09 +0000 (22:20 +0200)]
s390/bpf: Fix clobbering the caller's backchain in the trampoline
One of the first things that s390x kernel functions do is storing the
the caller's frame address (backchain) on stack. This makes unwinding
possible. The backchain is always stored at frame offset 152, which is
inside the 160-byte stack area, that the functions allocate for their
callees. The callees must preserve the backchain; the remaining 152
bytes they may use as they please.
Currently the trampoline uses all 160 bytes, clobbering the backchain.
This causes kernel panics when using __builtin_return_address() in
functions called by the trampoline.
Fix by reducing the usage of the caller-reserved stack area by 8 bytes
in the trampoline.
Will Mortensen [Fri, 6 Oct 2023 05:37:06 +0000 (22:37 -0700)]
net/mlx5e: Again mutually exclude RX-FCS and RX-port-timestamp
Commit 1e66220948df8 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs
flag change") seems to have accidentally inverted the logic added in
commit 0bc73ad46a76 ("net/mlx5e: Mutually exclude RX-FCS and
RX-port-timestamp").
The impact of this is a little unclear since it seems the FCS scattered
with RX-FCS is (usually?) correct regardless.
Gerd Bayer [Fri, 6 Oct 2023 12:58:47 +0000 (14:58 +0200)]
net/smc: Fix dependency of SMC on ISM
When the SMC protocol is built into the kernel proper while ISM is
configured to be built as module, linking the kernel fails due to
unresolved dependencies out of net/smc/smc_ism.o to
ism_get_smcd_ops, ism_register_client, and ism_unregister_client
as reported via the linux-next test automation (see link).
This however is a bug introduced a while ago.
Correct the dependency list in ISM's and SMC's Kconfig to reflect the
dependencies that are actually inverted. With this you cannot build a
kernel with CONFIG_SMC=y and CONFIG_ISM=m. Either ISM needs to be 'y',
too - or a 'n'. That way, SMC can still be configured on non-s390
architectures that do not have (nor need) an ISM driver.
Paolo Abeni [Tue, 10 Oct 2023 08:30:33 +0000 (10:30 +0200)]
Merge branch 'add-update_pn-flag'
Radu Pirea says:
====================
Add update_pn flag
Patches extracted from
https://lore.kernel.org/all/20230928084430.1882670[email protected]/
Update_pn flag will let the offloaded MACsec implementations to know when
the PN is updated.
====================
net/mlx5e: macsec: use update_pn flag instead of PN comparation
When updating the SA, use the new update_pn flags instead of comparing the
new PN with the initial one.
Comparing the initial PN value with the new value will allow the user
to update the SA using the initial PN value as a parameter like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \ ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 off
octeontx2-pf: mcs: update PN only when update_pn is true
When updating SA, update the PN only when the update_pn flag is true.
Otherwise, the PN will be reset to its previous value using the
following command and this should not happen:
$ ip macsec set macsec0 tx sa 0 on
net: macsec: indicate next pn update when offloading
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \ ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
David Vernet [Mon, 9 Oct 2023 16:14:14 +0000 (11:14 -0500)]
selftests/bpf: Add testcase for async callback return value failure
A previous commit updated the verifier to print an accurate failure
message for when someone specifies a nonzero return value from an async
callback. This adds a testcase for validating that the verifier emits
the correct message in such a case.
David Vernet [Mon, 9 Oct 2023 16:14:13 +0000 (11:14 -0500)]
bpf: Fix verifier log for async callback return values
The verifier, as part of check_return_code(), verifies that async
callbacks such as from e.g. timers, will return 0. It does this by
correctly checking that R0->var_off is in tnum_const(0), which
effectively checks that it's in a range of 0. If this condition fails,
however, it prints an error message which says that the value should
have been in (0x0; 0x1). This results in possibly confusing output such
as the following in which an async callback returns 1:
At async callback the register R0 has value (0x1; 0x0) should have been in (0x0; 0x1)
The fix is easy -- we should just pass the tnum_const(0) as the correct
range to verbose_invalid_scalar(), which will then print the following:
At async callback the register R0 has value (0x1; 0x0) should have been in (0x0; 0x0)
Andrew Kanner [Sat, 7 Oct 2023 07:51:49 +0000 (10:51 +0300)]
xdp: Fix zero-size allocation warning in xskq_create()
Syzkaller reported the following issue:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2807 at mm/vmalloc.c:3247 __vmalloc_node_range (mm/vmalloc.c:3361)
Modules linked in:
CPU: 0 PID: 2807 Comm: repro Not tainted 6.6.0-rc2+ #12
Hardware name: Generic DT based system
unwind_backtrace from show_stack (arch/arm/kernel/traps.c:258)
show_stack from dump_stack_lvl (lib/dump_stack.c:107 (discriminator 1))
dump_stack_lvl from __warn (kernel/panic.c:633 kernel/panic.c:680)
__warn from warn_slowpath_fmt (./include/linux/context_tracking.h:153 kernel/panic.c:700)
warn_slowpath_fmt from __vmalloc_node_range (mm/vmalloc.c:3361 (discriminator 3))
__vmalloc_node_range from vmalloc_user (mm/vmalloc.c:3478)
vmalloc_user from xskq_create (net/xdp/xsk_queue.c:40)
xskq_create from xsk_setsockopt (net/xdp/xsk.c:953 net/xdp/xsk.c:1286)
xsk_setsockopt from __sys_setsockopt (net/socket.c:2308)
__sys_setsockopt from ret_fast_syscall (arch/arm/kernel/entry-common.S:68)
xskq_get_ring_size() uses struct_size() macro to safely calculate the
size of struct xsk_queue and q->nentries of desc members. But the
syzkaller repro was able to set q->nentries with the value initially
taken from copy_from_sockptr() high enough to return SIZE_MAX by
struct_size(). The next PAGE_ALIGN(size) is such case will overflow
the size_t value and set it to 0. This will trigger WARN_ON_ONCE in
vmalloc_user() -> __vmalloc_node_range().
Björn Töpel [Wed, 4 Oct 2023 12:07:06 +0000 (14:07 +0200)]
riscv, bpf: Track both a0 (RISC-V ABI) and a5 (BPF) return values
The RISC-V BPF uses a5 for BPF return values, which are zero-extended,
whereas the RISC-V ABI uses a0 which is sign-extended. In other words,
a5 and a0 can differ, and are used in different context.
The BPF trampoline are used for both BPF programs, and regular kernel
functions.
Make sure that the RISC-V BPF trampoline saves, and restores both a0
and a5.
Björn Töpel [Wed, 4 Oct 2023 12:07:05 +0000 (14:07 +0200)]
riscv, bpf: Sign-extend return values
The RISC-V architecture does not expose sub-registers, and hold all
32-bit values in a sign-extended format [1] [2]:
| The compiler and calling convention maintain an invariant that all
| 32-bit values are held in a sign-extended format in 64-bit
| registers. Even 32-bit unsigned integers extend bit 31 into bits
| 63 through 32. Consequently, conversion between unsigned and
| signed 32-bit integers is a no-op, as is conversion from a signed
| 32-bit integer to a signed 64-bit integer.
While BPF, on the other hand, exposes sub-registers, and use
zero-extension (similar to arm64/x86).
This has led to some subtle bugs, where a BPF JITted program has not
sign-extended the a0 register (return value in RISC-V land), passed
the return value up the kernel, e.g.:
| int from_bpf(void);
|
| long foo(void)
| {
| return from_bpf();
| }
Here, a0 would be 0xffff_ffff, instead of the expected
0xffff_ffff_ffff_ffff.
Internally, the RISC-V JIT uses a5 as a dedicated register for BPF
return values.
Keep a5 zero-extended, but explicitly sign-extend a0 (which is used
outside BPF land). Now that a0 (RISC-V ABI) and a5 (BPF ABI) differs,
a0 is only moved to a5 for non-BPF native calls (BPF_PSEUDO_CALL).
When one of the LAG interfaces is in switchdev mode, setting default rule
can't be done.
The interface on which switchdev is running has ice_set_rx_mode() blocked
to avoid default rule adding (and other rules). The other interfaces
(without switchdev running but connected via bond with interface that
runs switchdev) can't follow the same scheme, because rx filtering needs
to be disabled when failover happens. Notification for bridge to set
promisc mode seems like good place to do that.
Roger Pau Monne [Thu, 5 Oct 2023 14:08:31 +0000 (16:08 +0200)]
xen-netback: use default TX queue size for vifs
Do not set netback interfaces (vifs) default TX queue size to the ring size.
The TX queue size is not related to the ring size, and using the ring size (32)
as the queue size can lead to packet drops. Note the TX side of the vif
interface in the netback domain is the one receiving packets to be injected
to the guest.
Do not explicitly set the TX queue length to any value when creating the
interface, and instead use the system default. Note that the queue length can
also be adjusted at runtime.
Dan Carpenter [Thu, 5 Oct 2023 14:00:12 +0000 (17:00 +0300)]
mlxsw: fix mlxsw_sp2_nve_vxlan_learning_set() return type
The mlxsw_sp2_nve_vxlan_learning_set() function is supposed to return
zero on success or negative error codes. So it needs to be type int
instead of bool.
Fixes: 4ee70efab68d ("mlxsw: spectrum_nve: Add support for VXLAN on Spectrum-2") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Petr Machata <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dinghao Liu [Sat, 7 Oct 2023 03:30:49 +0000 (11:30 +0800)]
ieee802154: ca8210: Fix a potential UAF in ca8210_probe
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Daniel Borkmann [Fri, 6 Oct 2023 22:06:55 +0000 (00:06 +0200)]
selftests/bpf: Make seen_tc* variable tests more robust
Martin reported that on his local dev machine the test_tc_chain_mixed() fails as
"test_tc_chain_mixed:FAIL:seen_tc5 unexpected seen_tc5: actual 1 != expected 0"
and others occasionally, too.
However, when running in a more isolated setup (qemu in particular), it works fine
for him. The reason is that there is a small race-window where seen_tc* could turn
into true for various test cases when there is background traffic, e.g. after the
asserts they often get reset. In such case when subsequent detach takes place,
unrelated background traffic could have already flipped the bool to true beforehand.
Add a small helper tc_skel_reset_all_seen() to reset all bools before we do the ping
test. At this point, everything is set up as expected and therefore no race can occur.
All tc_{opts,links} tests continue to pass after this change.
Daniel Borkmann [Fri, 6 Oct 2023 22:06:54 +0000 (00:06 +0200)]
selftests/bpf: Test query on empty mprog and pass revision into attach
Add a new test case to query on an empty bpf_mprog and pass the revision
directly into expected_revision for attachment to assert that this does
succeed.
Daniel Borkmann [Fri, 6 Oct 2023 22:06:53 +0000 (00:06 +0200)]
selftests/bpf: Adapt assert_mprog_count to always expect 0 count
Simplify __assert_mprog_count() to remove the -ENOENT corner case as the
bpf_prog_query() now returns 0 when no bpf_mprog is attached. This also
allows to convert a few test cases from using raw __assert_mprog_count()
over to plain assert_mprog_count() helper.
Daniel Borkmann [Fri, 6 Oct 2023 22:06:52 +0000 (00:06 +0200)]
selftests/bpf: Test bpf_mprog query API via libbpf and raw syscall
Add a new test case which performs double query of the bpf_mprog through
libbpf API, but also via raw bpf(2) syscall. This is testing to gather
first the count and then in a subsequent probe the full information with
the program array without clearing passed structs in between.
Lorenz Bauer [Fri, 6 Oct 2023 22:06:51 +0000 (00:06 +0200)]
bpf: Refuse unused attributes in bpf_prog_{attach,detach}
The recently added tcx attachment extended the BPF UAPI for attaching and
detaching by a couple of fields. Those fields are currently only supported
for tcx, other types like cgroups and flow dissector silently ignore the
new fields except for the new flags.
This is problematic once we extend bpf_mprog to older attachment types, since
it's hard to figure out whether the syscall really was successful if the
kernel silently ignores non-zero values.
Explicitly reject non-zero fields relevant to bpf_mprog for attachment types
which don't use the latter yet.
Daniel Borkmann [Fri, 6 Oct 2023 22:06:50 +0000 (00:06 +0200)]
bpf: Handle bpf_mprog_query with NULL entry
Improve consistency for bpf_mprog_query() API and let the latter also handle
a NULL entry as can be the case for tcx. Instead of returning -ENOENT, we
copy a count of 0 and revision of 1 to user space, so that this can be fed
into a subsequent bpf_mprog_attach() call as expected_revision. A BPF self-
test as part of this series has been added to assert this case.
Daniel Borkmann [Fri, 6 Oct 2023 22:06:49 +0000 (00:06 +0200)]
bpf: Fix BPF_PROG_QUERY last field check
While working on the ebpf-go [0] library integration for bpf_mprog and tcx,
Lorenz noticed that two subsequent BPF_PROG_QUERY requests currently fail. A
typical workflow is to first gather the bpf_mprog count without passing program/
link arrays, followed by the second request which contains the actual array
pointers.
The initial call populates count and revision fields. The second call gets
rejected due to a BPF_PROG_QUERY_LAST_FIELD bug which should point to
query.revision instead of query.link_attach_flags since the former is really
the last member.
It was not noticed in libbpf as bpf_prog_query_opts() always calls bpf(2) with
an on-stack bpf_attr that is memset() each time (and therefore query.revision
was reset to zero).
This patch series fixes use-after-free issues in ravb_remove().
The original patch is made by Zheng Wang [1]. And, I made the patch
1/2 which I found other issue in the ravb_remove().
ravb: Fix use-after-free issue in ravb_tx_timeout_work()
The ravb_stop() should call cancel_work_sync(). Otherwise,
ravb_tx_timeout_work() is possible to use the freed priv after
ravb_remove() was called like below:
unregister_netdev() will call .ndo_stop() so that ravb_stop() is
called. And, after phy_stop() is called, netif_carrier_off()
is also called. So that .ndo_tx_timeout() will not be called
after phy_stop().
Moshe Shemesh [Thu, 5 Oct 2023 12:50:16 +0000 (15:50 +0300)]
devlink: Hold devlink lock on health reporter dump get
Devlink health dump get callback should take devlink lock as any other
devlink callback. Otherwise, since devlink_mutex was removed, this
callback is not protected from a race of the reporter being destroyed
while handling the callback.
Add devlink lock to the callback and to any call for
devlink_health_do_dump(). This should be safe as non of the drivers dump
callback implementation takes devlink lock.
As devlink lock is added to any callback of dump, the reporter dump_lock
is now redundant and can be removed.
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Miquel Raynal [Mon, 2 Oct 2023 16:02:06 +0000 (18:02 +0200)]
can: sja1000: Always restart the Tx queue after an overrun
Upstream commit 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
arm64: dts: imx93: add the Flex-CAN stop mode by GPR
imx93 A0 chip use the internal q-channel handshake signal in LPCG
and CCM to automatically handle the Flex-CAN stop mode. But this
method meet issue when do the system PM stress test. IC can't fix
it easily. So in the new imx93 A1 chip, IC drop this method, and
involve back the old way，use the GPR method to trigger the Flex-CAN
stop mode signal. Now NXP claim to drop imx93 A0, and only support
imx93 A1. So here add the stop mode through GPR.
John Watts [Tue, 5 Sep 2023 23:13:43 +0000 (09:13 +1000)]
can: sun4i_can: Only show Kconfig if ARCH_SUNXI is set
When adding the RISCV option I didn't gate it behind ARCH_SUNXI.
As a result this option shows up with Allwinner support isn't enabled.
Fix that by requiring ARCH_SUNXI to be set if RISCV is set.
Lukas Magel [Sun, 27 Aug 2023 09:22:05 +0000 (09:22 +0000)]
can: isotp: isotp_sendmsg(): fix TX state detection and wait behavior
With patch [1], isotp_poll was updated to also queue the poller in the
so->wait queue, which is used for send state changes. Since the queue
now also contains polling tasks that are not interested in sending, the
queue fill state can no longer be used as an indication of send
readiness. As a consequence, nonblocking writes can lead to a race and
lock-up of the socket if there is a second task polling the socket in
parallel.
With this patch, isotp_sendmsg does not consult wq_has_sleepers but
instead tries to atomically set so->tx.state and waits on so->wait if it
is unable to do so. This behavior is in alignment with isotp_poll, which
also checks so->tx.state to determine send readiness.
net: sched: cls_u32: Fix allocation size in u32_init()
commit d61491a51f7e ("net/sched: cls_u32: Replace one-element array
with flexible-array member") incorrecly replaced an instance of
`sizeof(*tp_c)` with `struct_size(tp_c, hlist->ht, 1)`. This results
in a an over-allocation of 8 bytes.
This change is wrong because `hlist` in `struct tc_u_common` is a
pointer:
Marek Behún [Wed, 4 Oct 2023 09:19:04 +0000 (11:19 +0200)]
net: dsa: qca8k: fix potential MDIO bus conflict when accessing internal PHYs via management frames
Besides the QCA8337 switch the Turris 1.x device has on it's MDIO bus
also Micron ethernet PHY (dedicated to the WAN port).
We've been experiencing a strange behavior of the WAN ethernet
interface, wherein the WAN PHY started timing out the MDIO accesses, for
example when the interface was brought down and then back up.
Bisecting led to commit 2cd548566384 ("net: dsa: qca8k: add support for
phy read/write with mgmt Ethernet"), which added support to access the
QCA8337 switch's internal PHYs via management ethernet frames.
Connecting the MDIO bus pins onto an oscilloscope, I was able to see
that the MDIO bus was active whenever a request to read/write an
internal PHY register was done via an management ethernet frame.
My theory is that when the switch core always communicates with the
internal PHYs via the MDIO bus, even when externally we request the
access via ethernet. This MDIO bus is the same one via which the switch
and internal PHYs are accessible to the board, and the board may have
other devices connected on this bus. An ASCII illustration may give more
insight:
When we send a request to read an internal PHY register via an ethernet
management frame via eth1, the switch core receives the ethernet frame
on port 0 and then communicates with the internal PHY via MDIO. At this
time, other potential devices, such as the WAN PHY on Turris 1.x, cannot
use the MDIO bus, since it may cause a bus conflict.
Fix this issue by locking the MDIO bus even when we are accessing the
PHY registers via ethernet management frames.
Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet") Signed-off-by: Marek Behún <[email protected]> Reviewed-by: Christian Marangi <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Marek Behún [Wed, 4 Oct 2023 09:19:03 +0000 (11:19 +0200)]
net: dsa: qca8k: fix regmap bulk read/write methods on big endian systems
Commit c766e077d927 ("net: dsa: qca8k: convert to regmap read/write
API") introduced bulk read/write methods to qca8k's regmap.
The regmap bulk read/write methods get the register address in a buffer
passed as a void pointer parameter (the same buffer contains also the
read/written values). The register address occupies only as many bytes
as it requires at the beginning of this buffer. For example if the
.reg_bits member in regmap_config is 16 (as is the case for this
driver), the register address occupies only the first 2 bytes in this
buffer, so it can be cast to u16.
But the original commit implementing these bulk read/write methods cast
the buffer to u32:
u32 reg = *(u32 *)reg_buf & U16_MAX;
taking the first 4 bytes. This works on little endian systems where the
first 2 bytes of the buffer correspond to the low 16-bits, but it
obviously cannot work on big endian systems.
Fix this by casting the beginning of the buffer to u16 as
u32 reg = *(u16 *)reg_buf;
David S. Miller [Fri, 6 Oct 2023 09:59:53 +0000 (10:59 +0100)]
Merge branch 'lynx-28g-fixes'
Vladimir Oltean says:
====================
Fixes for lynx-28g PHY driver
This series fixes some issues in the Lynx 28G SerDes driver, namely an
oops when unloading the module, a race between the periodic workqueue
and the PHY API, and a race between phy_set_mode_ext() calls on multiple
lanes on the same SerDes.
====================
Vladimir Oltean [Wed, 4 Oct 2023 11:17:08 +0000 (14:17 +0300)]
phy: lynx-28g: serialize concurrent phy_set_mode_ext() calls to shared registers
The protocol converter configuration registers PCC8, PCCC, PCCD
(implemented by the driver), as well as others, control protocol
converters from multiple lanes (each represented as a different
struct phy). So, if there are simultaneous calls to phy_set_mode_ext()
to lanes sharing the same PCC register (either for the "old" or for the
"new" protocol), corruption of the values programmed to hardware is
possible, because lynx_28g_rmw() has no locking.
Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take
the global spinlock from the phy_ops :: set_mode() implementation. There
are no other callers which modify PCC registers.
Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Vladimir Oltean [Wed, 4 Oct 2023 11:17:07 +0000 (14:17 +0300)]
phy: lynx-28g: lock PHY while performing CDR lock workaround
lynx_28g_cdr_lock_check() runs once per second in a workqueue to reset
the lane receiver if the CDR has not locked onto bit transitions in the
RX stream. But the PHY consumer may do stuff with the PHY simultaneously,
and that isn't okay. Block concurrent generic PHY calls by holding the
PHY mutex from this workqueue.
Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G") Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Ioana Ciornei [Wed, 4 Oct 2023 11:17:06 +0000 (14:17 +0300)]
phy: lynx-28g: cancel the CDR check work item on the remove path
The blamed commit added the CDR check work item but didn't cancel it on
the remove path. Fix this by adding a remove function which takes care
of it.
Fixes: 8f73b37cf3fb ("phy: add support for the Layerscape SerDes 28G") Signed-off-by: Ioana Ciornei <[email protected]> Signed-off-by: Vladimir Oltean <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Thu, 5 Oct 2023 18:29:21 +0000 (11:29 -0700)]
Merge tag 'net-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from Bluetooth, netfilter, BPF and WiFi.
I didn't collect precise data but feels like we've got a lot of 6.5
fixes here. WiFi fixes are most user-awaited.
Current release - regressions:
- Bluetooth: fix hci_link_tx_to RCU lock usage
Current release - new code bugs:
- bpf: mprog: fix maximum program check on mprog attachment
- eth: ti: icssg-prueth: fix signedness bug in prueth_init_tx_chns()
Previous releases - regressions:
- ipv6: tcp: add a missing nf_reset_ct() in 3WHS handling
- vringh: don't use vringh_kiov_advance() in vringh_iov_xfer(), it
doesn't handle zero length like we expected
- wifi:
- cfg80211: fix cqm_config access race, fix crashes with brcmfmac
- iwlwifi: mvm: handle PS changes in vif_cfg_changed
- mac80211: fix mesh id corruption on 32 bit systems
- mt76: mt76x02: fix MT76x0 external LNA gain handling
- Bluetooth: fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER
- l2tp: fix handling of transhdrlen in __ip{,6}_append_data()
- dsa: mv88e6xxx: avoid EEPROM timeout when EEPROM is absent
- eth: stmmac: fix the incorrect parameter after refactoring
Previous releases - always broken:
- net: replace calls to sock->ops->connect() with kernel_connect(),
prevent address rewrite in kernel_bind(); otherwise BPF hooks may
modify arguments, unexpectedly to the caller
- tcp: fix delayed ACKs when reads and writes align with MSS
- bpf:
- verifier: unconditionally reset backtrack_state masks on global
func exit
- s390: let arch_prepare_bpf_trampoline return program size, fix
struct_ops offsets
- sockmap: fix accounting of available bytes in presence of PEEKs
- sockmap: reject sk_msg egress redirects to non-TCP sockets
- ipv4/fib: send netlink notify when delete source address routes
- ethtool: plca: fix width of reads when parsing netlink commands
- netfilter: nft_payload: rebuild vlan header on h_proto access
- Bluetooth: hci_codec: fix leaking memory of local_codecs
- eth: stmmac:
- dwmac-stm32: fix resume on STM32 MCU
- remove buggy and unneeded stmmac_poll_controller, depend on NAPI
- ibmveth: always recompute TCP pseudo-header checksum, fix use of
the driver with Open vSwitch
- wifi:
- rtw88: rtw8723d: fix MAC address offset in EEPROM
- mt76: fix lock dependency problem for wed_lock
- mwifiex: sanity check data reported by the device
- iwlwifi: ensure ack flag is properly cleared
- iwlwifi: mvm: fix a memory corruption due to bad pointer arithm
- iwlwifi: mvm: fix incorrect usage of scan API
Misc:
- wifi: mac80211: work around Cisco AP 9115 VHT MPDU length"
* tag 'net-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (99 commits)
MAINTAINERS: update Matthieu's email address
mptcp: userspace pm allow creating id 0 subflow
mptcp: fix delegated action races
net: stmmac: remove unneeded stmmac_poll_controller
net: lan743x: also select PHYLIB
net: ethernet: mediatek: disable irq before schedule napi
net: mana: Fix oversized sge0 for GSO packets
net: mana: Fix the tso_bytes calculation
net: mana: Fix TX CQE error handling
netlink: annotate data-races around sk->sk_err
sctp: update hb timer immediately after users change hb_interval
sctp: update transport state when processing a dupcook packet
tcp: fix delayed ACKs for MSS boundary condition
tcp: fix quick-ack counting to count actual ACKs of new data
page_pool: fix documentation typos
tipc: fix a potential deadlock on &tx->lock
net: stmmac: dwmac-stm32: fix resume on STM32 MCU
ipv4: Set offload_failed flag in fibmatch results
netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
netfilter: nf_tables: Deduplicate nft_register_obj audit logs
...
Linus Torvalds [Thu, 5 Oct 2023 17:56:18 +0000 (10:56 -0700)]
Merge tag 'ovl-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Amir Goldstein:
- Fix for file reference leak regression
- Fix for NULL pointer deref regression
- Fixes for RCU-walk race regressions:
Two of the fixes were taken from Al's RCU pathwalk race fixes series
with his consent [1].
Note that unlike most of Al's series, these two patches are not about
racing with ->kill_sb() and they are also very recent regressions
from v6.5, so I think it's worth getting them into v6.5.y.
There is also a fix for an RCU pathwalk race with ->kill_sb(), which
may have been solved in vfs generic code as you suggested, but it
also rids overlayfs from a nasty hack, so I think it's worth anyway.
Link: https://lore.kernel.org/linux-fsdevel/20231003204749.GA800259@ZenIV/
* tag 'ovl-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix NULL pointer defer when encoding non-decodable lower fid
ovl: make use of ->layers safe in rcu pathwalk
ovl: fetch inode once in ovl_dentry_revalidate_common()
ovl: move freeing ovl_entry past rcu delay
ovl: fix file reference leak when submitting aio
====================
mptcp: Fixes and maintainer email update for v6.6
Patch 1 addresses a race condition in MPTCP "delegated actions"
infrastructure. Affects v5.19 and later.
Patch 2 removes an unnecessary restriction that did not allow additional
outgoing subflows using the local address of the initial MPTCP subflow.
v5.16 and later.
Geliang Tang [Wed, 4 Oct 2023 20:38:12 +0000 (13:38 -0700)]
mptcp: userspace pm allow creating id 0 subflow
This patch drops id 0 limitation in mptcp_nl_cmd_sf_create() to allow
creating additional subflows with the local addr ID 0.
There is no reason not to allow additional subflows from this local
address: we should be able to create new subflows from the initial
endpoint. This limitation was breaking fullmesh support from userspace.
Paolo Abeni [Wed, 4 Oct 2023 20:38:11 +0000 (13:38 -0700)]
mptcp: fix delegated action races
The delegated action infrastructure is prone to the following
race: different CPUs can try to schedule different delegated
actions on the same subflow at the same time.
Each of them will check different bits via mptcp_subflow_delegate(),
and will try to schedule the action on the related per-cpu napi
instance.
Depending on the timing, both can observe an empty delegated list
node, causing the same entry to be added simultaneously on two different
lists.
The root cause is that the delegated actions infra does not provide
a single synchronization point. Address the issue reserving an additional
bit to mark the subflow as scheduled for delegation. Acquiring such bit
guarantee the caller to own the delegated list node, and being able to
safely schedule the subflow.
Clear such bit only when the subflow scheduling is completed, ensuring
proper barrier in place.
Additionally swap the meaning of the delegated_action bitmask, to allow
the usage of the existing helper to set multiple bit at once.
Using netconsole netpoll_poll_dev could be called from interrupt
context, thus using disable_irq() would cause the following kernel
warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:137
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0
CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117
Hardware name: aml (r1) (DT)
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x14/0x20
dump_stack_lvl+0x8c/0xac
dump_stack+0x18/0x30
___might_sleep+0x150/0x194
__might_sleep+0x64/0xbc
synchronize_irq+0x8c/0x150
disable_irq+0x2c/0x40
stmmac_poll_controller+0x140/0x1a0
netpoll_poll_dev+0x6c/0x220
netpoll_send_skb+0x308/0x390
netpoll_send_udp+0x418/0x760
write_msg+0x118/0x140 [netconsole]
console_unlock+0x404/0x500
vprintk_emit+0x118/0x250
dev_vprintk_emit+0x19c/0x1cc
dev_printk_emit+0x90/0xa8
__dev_printk+0x78/0x9c
_dev_warn+0xa4/0xbc
ath10k_warn+0xe8/0xf0 [ath10k_core]
ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core]
ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci]
__napi_poll+0x58/0x1f4
net_rx_action+0x504/0x590
_stext+0x1b8/0x418
run_ksoftirqd+0x74/0xa4
smpboot_thread_fn+0x210/0x3c0
kthread+0x1fc/0x210
ret_from_fork+0x10/0x20
Since [0] .ndo_poll_controller is only needed if driver doesn't or
partially use NAPI. Because stmmac does so, stmmac_poll_controller
can be removed fixing the above warning.
[0] commit ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional")
net: ethernet: mediatek: disable irq before schedule napi
While searching for possible refactor of napi_schedule_prep and
__napi_schedule it was notice that the mtk eth driver disable the
interrupt for rx and tx AFTER napi is scheduled.
While this is a very hard to repro case it might happen to have
situation where the interrupt is disabled and never enabled again as the
napi completes and the interrupt is enabled before.
This is caused by the fact that a napi driven by interrupt expect a
logic with:
1. interrupt received. napi prepared -> interrupt disabled -> napi
scheduled
2. napi triggered. ring cleared -> interrupt enabled -> wait for new
interrupt
To prevent this case, disable the interrupt BEFORE the napi is
scheduled.
For an unknown TX CQE error type (probably from a newer hardware),
still free the SKB, update the queue tail, etc., otherwise the
accounting will be wrong.
Also, TX errors can be triggered by injecting corrupted packets, so
replace the WARN_ONCE to ratelimited error logging.
Linus Torvalds [Thu, 5 Oct 2023 01:19:55 +0000 (18:19 -0700)]
Merge tag 'rtla-v6.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bristot/linux
Pull rtla fixes from Daniel Bristot de Oliveira:
"rtla (Real-Time Linux Analysis) tool fixes.
Timerlat auto-analysis:
- Timerlat is reporting thread interference time without thread noise
events occurrence. It was caused because the thread interference
variable was not reset after the analysis of a timerlat activation
that did not hit the threshold.
- The IRQ handler delay is estimated from the delta of the IRQ
latency reported by timerlat, and the timestamp from IRQ handler
start event. If the delta is near-zero, the drift from the external
clock and the trace event and/or the overhead can cause the value
to be negative. If the value is negative, print a zero-delay.
- IRQ handlers happening after the timerlat thread event but before
the stop tracing were being reported as IRQ that happened before
the *current* IRQ occurrence. Ignore Previous IRQ noise in this
condition because they are valid only for the *next* timerlat
activation.
Timerlat user-space:
- Timerlat is stopping all user-space thread if a CPU becomes
offline. Do not stop the entire tool if a CPU is/become offline,
but only the thread of the unavailable CPU. Stop the tool only, if
all threads leave because the CPUs become/are offline.
man-pages:
- Fix command line example in timerlat hist man page"
* tag 'rtla-v6.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bristot/linux:
rtla: fix a example in rtla-timerlat-hist.rst
rtla/timerlat: Do not stop user-space if a cpu is offline
rtla/timerlat_aa: Fix previous IRQ delay for IRQs that happens after thread sample
rtla/timerlat_aa: Fix negative IRQ delay
rtla/timerlat_aa: Zero thread sum after every sample analysis
Eric Dumazet [Tue, 3 Oct 2023 18:34:55 +0000 (18:34 +0000)]
netlink: annotate data-races around sk->sk_err
syzbot caught another data-race in netlink when
setting sk->sk_err.
Annotate all of them for good measure.
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
write to 0xffff8881613bb220 of 4 bytes by task 28147 on cpu 0:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffff8881613bb220 of 4 bytes by task 28146 on cpu 1:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00000000 -> 0x00000016
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 28146 Comm: syz-executor.0 Not tainted 6.6.0-rc3-syzkaller-00055-g9ed22ae6be81 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/06/2023
Xin Long [Sun, 1 Oct 2023 15:04:20 +0000 (11:04 -0400)]
sctp: update hb timer immediately after users change hb_interval
Currently, when hb_interval is changed by users, it won't take effect
until the next expiry of hb timer. As the default value is 30s, users
have to wait up to 30s to wait its hb_interval update to work.
This becomes pretty bad in containers where a much smaller value is
usually set on hb_interval. This patch improves it by resetting the
hb timer immediately once the value of hb_interval is updated by users.
Note that we don't address the already existing 'problem' when sending
a heartbeat 'on demand' if one hb has just been sent(from the timer)
mentioned in:
Xin Long [Sun, 1 Oct 2023 14:58:45 +0000 (10:58 -0400)]
sctp: update transport state when processing a dupcook packet
During the 4-way handshake, the transport's state is set to ACTIVE in
sctp_process_init() when processing INIT_ACK chunk on client or
COOKIE_ECHO chunk on server.
when processing COOKIE_ECHO on 192.168.1.2, as it's in COOKIE_WAIT state,
sctp_sf_do_dupcook_b() is called by sctp_sf_do_5_2_4_dupcook() where it
creates a new association and sets its transport to ACTIVE then updates
to the old association in sctp_assoc_update().
However, in sctp_assoc_update(), it will skip the transport update if it
finds a transport with the same ipaddr already existing in the old asoc,
and this causes the old asoc's transport state not to move to ACTIVE
after the handshake.
This means if DATA retransmission happens at this moment, it won't be able
to enter PF state because of the check 'transport->state == SCTP_ACTIVE'
in sctp_do_8_2_transport_strike().
This patch fixes it by updating the transport in sctp_assoc_update() with
sctp_assoc_add_peer() where it updates the transport state if there is
already a transport with the same ipaddr exists in the old asoc.
Neal Cardwell [Sun, 1 Oct 2023 15:12:39 +0000 (11:12 -0400)]
tcp: fix delayed ACKs for MSS boundary condition
This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.
The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:
(1) If an app reads data when > 1*MSS is unacknowledged, then
tcp_cleanup_rbuf() ACKs immediately because of:
(2) If an app reads all received data, and the packets were < 1*MSS,
and either (a) the app is not ping-pong or (b) we received two
packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
of:
(3) *However*: if an app reads exactly 1*MSS of data,
tcp_cleanup_rbuf() does not send an immediate ACK. This is true
even if the app is not ping-pong and the 1*MSS of data had the PSH
bit set, suggesting the sending application completed an
application write.
Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.
The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.
Neal Cardwell [Sun, 1 Oct 2023 15:12:38 +0000 (11:12 -0400)]
tcp: fix quick-ack counting to count actual ACKs of new data
This commit fixes quick-ack counting so that it only considers that a
quick-ack has been provided if we are sending an ACK that newly
acknowledges data.
The code was erroneously using the number of data segments in outgoing
skbs when deciding how many quick-ack credits to remove. This logic
does not make sense, and could cause poor performance in
request-response workloads, like RPC traffic, where requests or
responses can be multi-segment skbs.
When a TCP connection decides to send N quick-acks, that is to
accelerate the cwnd growth of the congestion control module
controlling the remote endpoint of the TCP connection. That quick-ack
decision is purely about the incoming data and outgoing ACKs. It has
nothing to do with the outgoing data or the size of outgoing data.
And in particular, an ACK only serves the intended purpose of allowing
the remote congestion control to grow the congestion window quickly if
the ACK is ACKing or SACKing new data.
The fix is simple: only count packets as serving the goal of the
quickack mechanism if they are ACKing/SACKing new data. We can tell
whether this is the case by checking inet_csk_ack_scheduled(), since
we schedule an ACK exactly when we are ACKing/SACKing new data.
Jakub Kicinski [Wed, 4 Oct 2023 21:53:17 +0000 (14:53 -0700)]
Merge tag 'nf-23-10-04' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westphal says:
====================
netfilter patches for net
First patch resolves a regression with vlan header matching, this was
broken since 6.5 release. From myself.
Second patch fixes an ancient problem with sctp connection tracking in
case INIT_ACK packets are delayed. This comes with a selftest, both
patches from Xin Long.
Patch 4 extends the existing nftables audit selftest, from
Phil Sutter.
Patch 5, also from Phil, avoids a situation where nftables
would emit an audit record twice. This was broken since 5.13 days.
Patch 6, from myself, avoids spurious insertion failure if we encounter an
overlapping but expired range during element insertion with the
'nft_set_rbtree' backend. This problem exists since 6.2.
* tag 'nf-23-10-04' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: nft_set_rbtree: fix spurious insertion failure
netfilter: nf_tables: Deduplicate nft_register_obj audit logs
selftests: netfilter: Extend nft_audit.sh
selftests: netfilter: test for sctp collision processing in nf_conntrack
netfilter: handle the connecting collision properly in nf_conntrack_proto_sctp
netfilter: nft_payload: rebuild vlan header on h_proto access
====================
Chengfeng Ye [Wed, 27 Sep 2023 18:14:14 +0000 (18:14 +0000)]
tipc: fix a potential deadlock on &tx->lock
It seems that tipc_crypto_key_revoke() could be be invoked by
wokequeue tipc_crypto_work_rx() under process context and
timer/rx callback under softirq context, thus the lock acquisition
on &tx->lock seems better use spin_lock_bh() to prevent possible
deadlock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
Ben Wolsieffer [Wed, 27 Sep 2023 17:57:49 +0000 (13:57 -0400)]
net: stmmac: dwmac-stm32: fix resume on STM32 MCU
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Benjamin Poirier [Tue, 26 Sep 2023 18:27:30 +0000 (14:27 -0400)]
ipv4: Set offload_failed flag in fibmatch results
Due to a small omission, the offload_failed flag is missing from ipv4
fibmatch results. Make sure it is set correctly.
The issue can be witnessed using the following commands:
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add dummy1 up type dummy
ip route add 192.0.2.0/24 dev dummy1
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/fib/fail_route_offload
ip route add 198.51.100.0/24 dev dummy1
ip route
# 192.168.15.0/24 has rt_trap
# 198.51.100.0/24 has rt_offload_failed
ip route get 192.168.15.1 fibmatch
# Result has rt_trap
ip route get 198.51.100.1 fibmatch
# Result differs from the route shown by `ip route`, it is missing
# rt_offload_failed
ip link del dev dummy1
echo 1 > /sys/bus/netdevsim/del_device
Linus Torvalds [Wed, 4 Oct 2023 18:35:23 +0000 (11:35 -0700)]
Merge tag 'linux-kselftest-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"One single fix to Makefile to fix the incorrect TARGET name for uevent
test"
* tag 'linux-kselftest-fixes-6.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix wrong TARGET in kselftest top level Makefile
Jakub Kicinski [Wed, 4 Oct 2023 18:30:21 +0000 (11:30 -0700)]
Merge tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Quite a collection of fixes this time, really too many
to list individually. Many stack fixes, even rfkill
(found by simulation and the new eevdf scheduler)!
Also a bigger maintainers file cleanup, to remove old
and redundant information.
* tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (32 commits)
wifi: iwlwifi: mvm: Fix incorrect usage of scan API
wifi: mac80211: Create resources for disabled links
wifi: cfg80211: avoid leaking stack data into trace
wifi: mac80211: allow transmitting EAPOL frames with tainted key
wifi: mac80211: work around Cisco AP 9115 VHT MPDU length
wifi: cfg80211: Fix 6GHz scan configuration
wifi: mac80211: fix potential key leak
wifi: mac80211: fix potential key use-after-free
wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
wifi: brcmfmac: Replace 1-element arrays with flexible arrays
wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
wifi: rtw88: rtw8723d: Fix MAC address offset in EEPROM
rfkill: sync before userspace visibility/changes
wifi: mac80211: fix mesh id corruption on 32 bit systems
wifi: cfg80211: add missing kernel-doc for cqm_rssi_work
wifi: cfg80211: fix cqm_config access race
wifi: iwlwifi: mvm: Fix a memory corruption issue
wifi: iwlwifi: Ensure ack flag is properly cleared.
wifi: iwlwifi: dbg_ini: fix structure packing
iwlwifi: mvm: handle PS changes in vif_cfg_changed
...
====================
Jakub Kicinski [Wed, 4 Oct 2023 15:28:07 +0000 (08:28 -0700)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-10-02
We've added 11 non-merge commits during the last 12 day(s) which contain
a total of 12 files changed, 176 insertions(+), 41 deletions(-).
The main changes are:
1) Fix BPF verifier to reset backtrack_state masks on global function
exit as otherwise subsequent precision tracking would reuse them,
from Andrii Nakryiko.
2) Several sockmap fixes for available bytes accounting,
from John Fastabend.
3) Reject sk_msg egress redirects to non-TCP sockets given this
is only supported for TCP sockets today, from Jakub Sitnicki.
4) Fix a syzkaller splat in bpf_mprog when hitting maximum program
limits with BPF_F_BEFORE directive, from Daniel Borkmann
and Nikolay Aleksandrov.
5) Fix BPF memory allocator to use kmalloc_size_roundup() to adjust
size_index for selecting a bpf_mem_cache, from Hou Tao.
6) Fix arch_prepare_bpf_trampoline return code for s390 JIT,
from Song Liu.
7) Fix bpf_trampoline_get when CONFIG_BPF_JIT is turned off,
from Leon Hwang.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Use kmalloc_size_roundup() to adjust size_index
selftest/bpf: Add various selftests for program limits
bpf, mprog: Fix maximum program check on mprog attachment
bpf, sockmap: Reject sk_msg egress redirects to non-TCP sockets
bpf, sockmap: Add tests for MSG_F_PEEK
bpf, sockmap: Do not inc copied_seq when PEEK flag set
bpf: tcp_read_skb needs to pop skb regardless of seq
bpf: unconditionally reset backtrack_state masks on global func exit
bpf: Fix tr dereferencing
selftests/bpf: Check bpf_cubic_acked() is called via struct_ops
s390/bpf: Let arch_prepare_bpf_trampoline return program size
====================
nft_rbtree_gc_elem() walks back and removes the end interval element that
comes before the expired element.
There is a small chance that we've cached this element as 'rbe_ge'.
If this happens, we hold and test a pointer that has been queued for
freeing.
It also causes spurious insertion failures:
$ cat test-testcases-sets-0044interval_overlap_0.1/testout.log
Error: Could not process rule: File exists
add element t s { 0 - 2 }
^^^^^^
Failed to insert 0 - 2 given:
table ip t {
set s {
type inet_service
flags interval,timeout
timeout 2s
gc-interval 2s
}
}
The set (rbtree) is empty. The 'failure' doesn't happen on next attempt.
Reason is that when we try to insert, the tree may hold an expired
element that collides with the range we're adding.
While we do evict/erase this element, we can trip over this check:
if (rbe_ge && nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
return -ENOTEMPTY;
rbe_ge was erased by the synchronous gc, we should not have done this
check. Next attempt won't find it, so retry results in successful
insertion.
Restart in-kernel to avoid such spurious errors.
Such restart are rare, unless userspace intentionally adds very large
numbers of elements with very short timeouts while setting a huge
gc interval.
Even in this case, this cannot loop forever, on each retry an existing
element has been removed.
As the caller is holding the transaction mutex, its impossible
for a second entity to add more expiring elements to the tree.
After this it also becomes feasible to remove the async gc worker
and perform all garbage collection from the commit path.
Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection") Signed-off-by: Florian Westphal <[email protected]>
When adding/updating an object, the transaction handler emits suitable
audit log entries already, the one in nft_obj_notify() is redundant. To
fix that (and retain the audit logging from objects' 'update' callback),
Introduce an "audit log free" variant for internal use.
Fixes: c520292f29b8 ("audit: log nftables configuration change events once per table") Signed-off-by: Phil Sutter <[email protected]> Reviewed-by: Richard Guy Briggs <[email protected]> Acked-by: Paul Moore <[email protected]> (Audit) Signed-off-by: Florian Westphal <[email protected]>
Phil Sutter [Sat, 23 Sep 2023 01:53:49 +0000 (03:53 +0200)]
selftests: netfilter: Extend nft_audit.sh
Add tests for sets and elements and deletion of all kinds. Also
reorder rule reset tests: By moving the bulk rule add command up, the
two 'reset rules' tests become identical.
While at it, fix for a failing bulk rule add test's error status getting
lost due to its use in a pipe. Avoid this by using a temporary file.
Headings in diff output for failing tests contain no useful data, strip
them.
Xin Long [Tue, 3 Oct 2023 17:17:54 +0000 (13:17 -0400)]
selftests: netfilter: test for sctp collision processing in nf_conntrack
This patch adds a test case to reproduce the SCTP DATA chunk retransmission
timeout issue caused by the improper SCTP collision processing in netfilter
nf_conntrack_proto_sctp.
In this test, client sends a INIT chunk, but the INIT_ACK replied from
server is delayed until the server sends a INIT chunk to start a new
connection from its side. After the connection is complete from server
side, the delayed INIT_ACK arrives in nf_conntrack_proto_sctp.
The delayed INIT_ACK should be dropped in nf_conntrack_proto_sctp instead
of updating the vtag with the out-of-date init_tag, otherwise, the vtag
in DATA chunks later sent by client don't match the vtag in the conntrack
entry and the DATA chunks get dropped.
In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].
In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)
In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
(Scenario D)
Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.
There are also other Scenarios where it should allow the packet through,
addressed by the processing above:
Scenario C: new CT is created by INIT_ACK.
Scenario D: start INIT on the existing ESTABLISHED ct.
Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
(both side are stopped, then start new connection again in hours)
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]
David Wilder [Tue, 26 Sep 2023 21:42:51 +0000 (16:42 -0500)]
ibmveth: Remove condition to recompute TCP header checksum.
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Dan Carpenter [Tue, 26 Sep 2023 14:06:58 +0000 (17:06 +0300)]
dmaengine: ti: k3-udma-glue: clean up k3_udma_glue_tx_get_irq() return
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Dan Carpenter [Tue, 26 Sep 2023 14:05:59 +0000 (17:05 +0300)]
net: ti: icssg-prueth: Fix signedness bug in prueth_init_tx_chns()
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Roger Quadros <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Dan Carpenter [Tue, 26 Sep 2023 14:04:43 +0000 (17:04 +0300)]
net: ethernet: ti: am65-cpsw: Fix error code in am65_cpsw_nuss_init_tx_chns()
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Dan Carpenter <[email protected]> Reviewed-by: Roger Quadros <[email protected]> Signed-off-by: David S. Miller <[email protected]>
vringh: don't use vringh_kiov_advance() in vringh_iov_xfer()
In the while loop of vringh_iov_xfer(), `partlen` could be 0 if one of
the `iov` has 0 lenght.
In this case, we should skip the iov and go to the next one.
But calling vringh_kiov_advance() with 0 lenght does not cause the
advancement, since it returns immediately if asked to advance by 0 bytes.
Let's restore the code that was there before commit b8c06ad4d67d
("vringh: implement vringh_kiov_advance()"), avoiding using
vringh_kiov_advance().
projects / linux.git / log