Resolve some of the complaints from checkpatch, and remove "magic emacs format"
comments, and useless MODULE_SUPPORTED_DEVICE(). But should not
change actual code.
It is not safe to use a network device destructor that is a function in
the module, since it can be called after module is unloaded if sysfs
handle is open.
When eventually using netlink, the device cleanup code needs to be done
via uninit function.
Avoid a unnecessary carrier state transistion that happens when device
is registered.
Lockdep works better if initialization is done before registration as well.
Roland Dreier [Sat, 13 Jun 2009 22:14:09 +0000 (15:14 -0700)]
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.
Ben Dooks [Mon, 8 Jun 2009 22:33:57 +0000 (23:33 +0100)]
mmc_block: do not DMA to stack
In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.
Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.
[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Ian Molton [Fri, 12 Jun 2009 20:53:05 +0000 (21:53 +0100)]
tmio_mmc: fix clock setup
This patch fixes the clock setup in tmio_mmc.
* Incorrect divider setting
* Cruft written to the clock registers (seemingly harmless but Not
Good (tm))
It also eliminates some unnecessary ifs and tidies the loop syntax.
Thanks to Philipp Zabel who discovered the divider issue, commenting
"Except for the SDCLK = HCLK (divider bypassed) case, the clock
setting resulted in double the requested frequency.
The smallest possible frequency (f_max/512) is configured with
a divider setting 0x80, not 0x40."
Philipp Zabel [Thu, 4 Jun 2009 18:12:32 +0000 (20:12 +0200)]
tmio_mmc: add bus_shift support
Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Philipp Zabel [Thu, 4 Jun 2009 18:12:31 +0000 (20:12 +0200)]
MFD,mmc: tmio_mmc: make HCLK configurable
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Wolfgang Muees [Tue, 26 May 2009 07:56:19 +0000 (08:56 +0100)]
mmc_spi: don't use EINVAL for possible transmission errors
This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Michał Mirosław [Fri, 22 May 2009 18:33:59 +0000 (20:33 +0200)]
mmc: Driver for CB710/720 memory card reader (MMC part)
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Daniel Ribeiro [Thu, 21 May 2009 11:54:18 +0000 (08:54 -0300)]
pxamci: add regulator support.
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
mmc/omap: make mmci-omap using platform_driver_probe
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Wolfgang Muees [Wed, 8 Apr 2009 09:14:07 +0000 (10:14 +0100)]
mmc_spi: speedup for slow cards, less wear-out
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Jorg Schummer [Tue, 31 Mar 2009 14:51:21 +0000 (17:51 +0300)]
mmc: mmc_rescan detects card change in one run
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
The problem is that asm/signal.h has been made to include asm-generic/signal.h,
but the redundant stuff from asm/signal.h has not been discarded, leading to
multiple redefinitions.
Linus Torvalds [Sat, 13 Jun 2009 20:15:59 +0000 (13:15 -0700)]
Merge branch 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-ocores: Can add I2C devices to the bus
i2c-s3c2410: move to using platform idtable to match devices
i2c: OMAP3: Better noise suppression for fast/standard modes
i2c: OMAP2/3: Fix scll/sclh calculations
i2c: Blackfin TWI: implement I2C_FUNC_SMBUS_I2C_BLOCK functionality
i2c: Blackfin TWI: fix transfer errors with repeat start
i2c: Blackfin TWI: fix REPEAT START mode doesn't repeat
i2c: Blackfin TWI: make sure we don't end up with a CLKDIV=0
Linus Torvalds [Sat, 13 Jun 2009 20:08:34 +0000 (13:08 -0700)]
Merge branch 'docs-next' of git://git.lwn.net/linux-2.6
* 'docs-next' of git://git.lwn.net/linux-2.6:
Document the debugfs API
Documentation: Add "how to write a good patch summary" to SubmittingPatches
SubmittingPatches: fix typo
docs: Encourage better changelogs in the development process document
Document Reported-by in SubmittingPatches
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
Ingo Molnar [Sat, 13 Jun 2009 06:29:33 +0000 (08:29 +0200)]
[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
make[1]: *** [drivers/net/cnic.o] Error 1
make: *** [drivers/net/cnic.o] Error 2
The unaligned address exception handler (and others) does not scan the
fixup tables before oopsing. This is bad because it means passing a
badly aligned pointer from user space might crash the kernel.
Fix this by scanning the fixup tables in _exception(). This should
resolve the issue for unaligned addresses as well as other less common
exceptions that might be happening during a userspace access. The page
fault handler already does fixup processing.
This patch improves ctnetlink event reliability if one broadcast
listener has set the NETLINK_BROADCAST_ERROR socket option.
The logic is the following: if an event delivery fails, we keep
the undelivered events in the missed event cache. Once the next
packet arrives, we add the new events (if any) to the missed
events in the cache and we try a new delivery, and so on. Thus,
if ctnetlink fails to deliver an event, we try to deliver them
once we see a new packet. Therefore, we may lose state
transitions but the userspace process gets in sync at some point.
At worst case, if no events were delivered to userspace, we make
sure that destroy events are successfully delivered. Basically,
if ctnetlink fails to deliver the destroy event, we remove the
conntrack entry from the hashes and we insert them in the dying
list, which contains inactive entries. Then, the conntrack timer
is added with an extra grace timeout of random32() % 15 seconds
to trigger the event again (this grace timeout is tunable via
/proc). The use of a limited random timeout value allows
distributing the "destroy" resends, thus, avoiding accumulating
lots "destroy" events at the same time. Event delivery may
re-order but we can identify them by means of the tuple plus
the conntrack ID.
The maximum number of conntrack entries (active or inactive) is
still handled by nf_conntrack_max. Thus, we may start dropping
packets at some point if we accumulate a lot of inactive conntrack
entries that did not successfully report the destroy event to
userspace.
During my stress tests consisting of setting a very small buffer
of 2048 bytes for conntrackd and the NETLINK_BROADCAST_ERROR socket
flag, and generating lots of very small connections, I noticed
very few destroy entries on the fly waiting to be resend.
A simple way to test this patch consist of creating a lot of
entries, set a very small Netlink buffer in conntrackd (+ a patch
which is not in the git tree to set the BROADCAST_ERROR flag)
and invoke `conntrack -F'.
For expectations, no changes are introduced in this patch.
Currently, event delivery is only done for new expectations (no
events from expectation expiration, removal and confirmation).
In that case, they need a per-expectation event cache to implement
the same idea that is exposed in this patch.
This patch can be useful to provide reliable flow-accouting. We
still have to add a new conntrack extension to store the creation
and destroy time.
list_nulls: add hlist_nulls_add_head and hlist_nulls_del
This patch adds the hlist_nulls_add_head() function which is
based on hlist_nulls_add_head_rcu() but without the use of
rcu_assign_pointer(). It also adds hlist_nulls_del which is
exactly the same like hlist_nulls_del_rcu().
netfilter: conntrack: move helper destruction to nf_ct_helper_destroy()
This patch moves the helper destruction to a function that lives
in nf_conntrack_helper.c. This new function is used in the patch
to add ctnetlink reliable event delivery.
netfilter: conntrack: move event caching to conntrack extension infrastructure
This patch reworks the per-cpu event caching to use the conntrack
extension infrastructure.
The main drawback is that we consume more memory per conntrack
if event delivery is enabled. This patch is required by the
reliable event delivery that follows to this patch.
BTW, this patch allows you to enable/disable event delivery via
/proc/sys/net/netfilter/nf_conntrack_events in runtime, although
you can still disable event caching as compilation option.
Patrick McHardy [Sat, 13 Jun 2009 10:21:49 +0000 (12:21 +0200)]
netfilter: nf_conntrack: use mod_timer_pending() for conntrack refresh
Use mod_timer_pending() instead of atomic sequence of del_timer()/
add_timer(). mod_timer_pending() does not rearm an inactive timer,
so we don't need the conntrack lock anymore to make sure we don't
accidentally rearm a timer of a conntrack which is in the process
of being destroyed.
With this change, we don't need to take the global lock anymore at all,
counter updates can be performed under the per-conntrack lock.
Thomas Gleixner [Fri, 12 Jun 2009 09:29:27 +0000 (11:29 +0200)]
clocksource: prevent selection of low resolution clocksourse also for nohz=on
commit 3f68535adad (clocksource: sanity check sysfs clocksource
changes) prevents selection of non high resolution capable
clocksources when high resolution mode is active, but did not take
into account that the same rules apply for highres=off nohz=on.
Check the tick device mode instead of hrtimer_hres_active() to verify
whether the system needs to be protected from a switch to jiffies or
other non highres capable clock sources.
Richard Röjfors [Fri, 5 Jun 2009 13:40:32 +0000 (15:40 +0200)]
i2c-ocores: Can add I2C devices to the bus
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Ben Dooks [Fri, 12 Jun 2009 09:45:29 +0000 (10:45 +0100)]
i2c-s3c2410: move to using platform idtable to match devices
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
Frank Shew [Tue, 19 May 2009 11:23:49 +0000 (07:23 -0400)]
i2c: Blackfin TWI: fix transfer errors with repeat start
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Fix up USB drivers that return an errno value (result of usb_submit_urb())
to qdisc_restart(), causing qdisc_restart() to print a warning and requeue/
retransmit the skb.
- hso: skb is freed: use after free
- at76_usb: skb is freed: use after free
Fix up wireless drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- airo: transmission not implemented for chip, intention is to free and abort
- ipw2200: transmission not implemented for promiscous mode, intention is to
drop
- prism54: intention is to drop
- wl3501_cs: intention appears to be to drop
- zd1201: error counter indicates intention is to drop
Fix up IRDA drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- donauboe: intention appears to be to have the skb retransmitted without
error message
- irda-usb: intention is to drop silently according to comment
- kingsub-sir: skb is freed: use after free
- ks959-sir: skb is freed: use after free
- ksdazzle-sir: skb is freed: use after free
- mcs7880: skb is freed: use after free
Fix up drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning and requeue/retransmit the skb.
- xpnet: memory allocation error, intention is to drop
- ethoc: oversized packet, packet must be dropped
- ibmlana: skb freed: use after free
- rrunner: skb freed: use after free
Linus Torvalds [Sat, 13 Jun 2009 01:21:19 +0000 (18:21 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/configfs
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/configfs:
configfs: Rework configfs_depend_item() locking and make lockdep happy
configfs: Silence lockdep on mkdir() and rmdir()
Linus Torvalds [Sat, 13 Jun 2009 01:18:05 +0000 (18:18 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
Linus Torvalds [Sat, 13 Jun 2009 01:09:18 +0000 (18:09 -0700)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
Linus Torvalds [Fri, 12 Jun 2009 20:17:12 +0000 (13:17 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: use more NOFS allocation
dlm: connect to nodes earlier
dlm: fix use count with multiple joins
dlm: Make name input parameter of {,dlm_}new_lockspace() const
Linus Torvalds [Fri, 12 Jun 2009 20:16:52 +0000 (13:16 -0700)]
Merge branch 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Start documenting HAVE_PERF_COUNTERS requirements
perf_counter: Add forward/backward attribute ABI compatibility
perf record: Explicity program a default counter
perf_counter: Remove PERF_TYPE_RAW special casing
perf_counter: PERF_TYPE_HW_CACHE is a hardware counter too
powerpc, perf_counter: Fix performance counter event types
perf_counter/x86: Add a quirk for Atom processors
perf_counter tools: Remove one L1-data alias
Linus Torvalds [Fri, 12 Jun 2009 20:14:30 +0000 (13:14 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (62 commits)
Blackfin: fix sparseirq/kstat_irqs fallout
Blackfin: fix unused warnings after nommu update
Blackfin: export the last exception cause via debugfs
Blackfin: fix length checking in kgdb_ebin2mem
Blackfin: kgdb: fix up error return values
Blackfin: push access_ok() L1 attribute down
Blackfin: punt duplicated search_exception_table() prototype
Blackfin: add missing access_ok() checks to user functions
Blackfin: convert early_printk EVT init to a loop
Blackfin: document the lsl variants of the L1 allocator
Blackfin: rename Blackfin relocs according to the toolchain
Blackfin: check SIC defines rather than variant names
Blackfin: add SSYNC to set_dma_sg() for descriptor fetching
Blackfin: convert SMP to only use generic time framework
Blackfin: bf548-ezkit/bf537-stamp: add resources for ADXL345/346
Blackfin: override default uClinux MTD addr/size
Blackfin: fix command line corruption with DEBUG_DOUBLEFAULT
Blackfin: fix handling of initial L1 reservation
Blackfin: merge sram init functions
Blackfin: drop unused reserve_pda() function
...
Linus Torvalds [Fri, 12 Jun 2009 20:14:15 +0000 (13:14 -0700)]
Merge branch 'for-linus' of git://linux-arm.org/linux-2.6
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add more info to the MAINTAINERS entry
kmemleak: Remove the kmemleak.h include in drivers/char/vt.c
Heiko Carstens [Thu, 11 Jun 2009 19:59:21 +0000 (21:59 +0200)]
PM: Add empty suspend/resume device irq functions
git commit 0a0c5168 "PM: Introduce functions for suspending and resuming
device interrupts" introduced some helper functions. However these
functions are only available for architectures which support
GENERIC_HARDIRQS.
Other architectures will see this build error:
drivers/built-in.o: In function `sysdev_suspend':
(.text+0x15138): undefined reference to `check_wakeup_irqs'
drivers/built-in.o: In function `device_power_up':
(.text+0x1cb66): undefined reference to `resume_device_irqs'
drivers/built-in.o: In function `device_power_down':
(.text+0x1cb92): undefined reference to `suspend_device_irqs'
To fix this add some empty inline functions for !GENERIC_HARDIRQS.
Cornelia Huck [Tue, 9 Jun 2009 23:28:19 +0000 (01:28 +0200)]
PM/Hibernate: Move NVS routines into a seperate file (v2).
The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.
[rjw: Change the name of the new file to hibernate_nvs.c, add the
license line to the header comment.]
Change the name of kernel/power/disk.c to kernel/power/hibernate.c
in analogy with the file names introduced by the changes that
separated the suspend to RAM and standby funtionality from the
common PM functions.
PM: Separate suspend to RAM functionality from core
Move the suspend to RAM and standby code from kernel/power/main.c
to two separate files, kernel/power/suspend.c containing the basic
functions and kernel/power/suspend_test.c containing the automatic
suspend test facility based on the RTC clock alarm.
There are no changes in functionality related to these modifications.
This patch reworks the platform driver code for legacy
suspend and resume to avoid installing callbacks in
struct device_driver. A warning is also added telling
users to update the platform driver to use dev_pm_ops.
The functions platform_legacy_suspend()/resume() directly
call suspend and resume callbacks in struct platform_driver
instead of wrapping things in platform_drv_suspend()/resume().
Magnus Damm [Thu, 4 Jun 2009 20:13:25 +0000 (22:13 +0200)]
PM: Remove device_type suspend()/resume()
This patch removes the legacy callbacks ->suspend() and
->resume() from struct device_type. These callbacks seem
unused, and new code should instead make use of struct
dev_pm_ops.
PM/Hibernate: Move memory shrinking to snapshot.c (rev. 2)
A future patch is going to modify the memory shrinking code so that
it will make memory allocations to free memory instead of using an
artificial memory shrinking mechanism for that. For this purpose it
is convenient to move swsusp_shrink_memory() from
kernel/power/swsusp.c to kernel/power/snapshot.c, because the new
memory-shrinking code is going to use things that are local to
kernel/power/snapshot.c .
[rev. 2: Make some functions static and remove their headers from
kernel/power/power.h]
Remove the ->suspend_late() and ->resume_early() callbacks
from struct bus_type V2. These callbacks are legacy stuff
at this point and since there seem to be no in-tree users
we may as well remove them. New users should use dev_pm_ops.
Alan Stern [Sun, 24 May 2009 20:05:42 +0000 (22:05 +0200)]
PM core: rename suspend and resume functions
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
Magnus Damm [Thu, 14 May 2009 22:53:26 +0000 (00:53 +0200)]
PM: Rename device_power_down/up()
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
projects / linux.git / log