Maulik Shah [Mon, 3 Jul 2023 08:55:54 +0000 (14:25 +0530)]
cpuidle: psci: Move enabling OSI mode after power domains creation
A switch from OSI to PC mode is only possible if all CPUs other than the
calling one are OFF, either through a call to CPU_OFF or not yet booted.
Currently OSI mode is enabled before power domains are created. In cases
where CPUidle states are not using hierarchical CPU topology the bail out
path tries to switch back to PC mode which gets denied by firmware since
other CPUs are online at this point and creates inconsistent state as
firmware is in OSI mode and Linux in PC mode.
This change moves enabling OSI mode after power domains are created,
this would makes sure that hierarchical CPU topology is used before
switching firmware to OSI mode.
$ tools/perf/trace/beauty/tracepoints/x86_msr.sh > before
$ cp arch/x86/include/asm/msr-index.h tools/arch/x86/include/asm/msr-index.h
$ tools/perf/trace/beauty/tracepoints/x86_msr.sh > after
$ diff -u before after
$
Just silences this perf build warning:
Warning: Kernel ABI header differences:
diff -u tools/arch/x86/include/asm/msr-index.h arch/x86/include/asm/msr-index.h
The tests were made with a specific workload, further tests on a
recently updated fedora 38 system with a system wide perf.data file
shows 'perf report' taking excessive time resolving inlines in vmlinux,
so lets revert this until a full investigation and improvement on the
addr2line support code is made.
Ping-Ke Shih [Tue, 8 Aug 2023 00:54:26 +0000 (08:54 +0800)]
wifi: rtw89: fix 8852AE disconnection caused by RX full flags
RX full flags are raised if certain types of RX FIFO are full, and then
drop all following MPDU of AMPDU. In order to resume to receive MPDU
when RX FIFO becomes available, we clear the register bits by the
commit a0d99ebb3ecd ("wifi: rtw89: initialize DMA of CMAC"). But, 8852AE
needs more settings to support this. To quickly fix disconnection problem,
revert the behavior as before.
Karol Herbst [Sat, 5 Aug 2023 10:18:13 +0000 (12:18 +0200)]
drm/nouveau/disp: Revert a NULL check inside nouveau_connector_get_modes
The original commit adding that check tried to protect the kenrel against
a potential invalid NULL pointer access.
However we call nouveau_connector_detect_depth once without a native_mode
set on purpose for non LVDS connectors and this broke DP support in a few
cases.
Yibin Ding [Wed, 2 Aug 2023 02:30:23 +0000 (10:30 +0800)]
mmc: block: Fix in_flight[issue_type] value error
For a completed request, after the mmc_blk_mq_complete_rq(mq, req)
function is executed, the bitmap_tags corresponding to the
request will be cleared, that is, the request will be regarded as
idle. If the request is acquired by a different type of process at
this time, the issue_type of the request may change. It further
caused the value of mq->in_flight[issue_type] to be abnormal,
and a large number of requests could not be sent.
Merge tag 'thunderbolt-for-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus
Mika writes:
thunderbolt: Fixes for v6.5-rc6
This includes two fixes for v6.5-rc6:
- Correct display flickering when connecting a Thunderbolt 3 device to
an AMD USB4 host controller
- Fix a memory leak in bandwidth allocation request.
Both have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Fix memory leak in tb_handle_dp_bandwidth_request()
thunderbolt: Fix Thunderbolt 3 display flickering issue on 2nd hot plug onwards
Xin Li [Wed, 22 Mar 2023 06:17:58 +0000 (23:17 -0700)]
x86/vdso: Choose the right GDT_ENTRY_CPUNODE for 32-bit getcpu() on 64-bit kernel
The vDSO getcpu() reads CPU ID from the GDT_ENTRY_CPUNODE entry when the RDPID
instruction is not available. And GDT_ENTRY_CPUNODE is defined as 28 on 32-bit
Linux kernel and 15 on 64-bit. But the 32-bit getcpu() on 64-bit Linux kernel
is compiled with 32-bit Linux kernel GDT_ENTRY_CPUNODE, i.e., 28, beyond the
64-bit Linux kernel GDT limit. Thus, it just fails _silently_.
When BUILD_VDSO32_64 is defined, choose the 64-bit Linux kernel GDT definitions
to compile the 32-bit getcpu().
$ ip route
10.0.0.0/24 dev swp5 proto kernel scope link src 10.0.0.1 rt_trap
10.0.1.0/24 nhid 20 via 10.0.0.2 dev swp5 rt_trap
When creating a route referencing a nexthop via its ID, the nexthop will
be stored in a separate nh pointer instead of the array of nexthops in
the fib_info struct. This causes issues since fib_info_nh() only handles
the nexthops array, but not the separate nh pointer, and will loudly
WARN about it.
In contrast fib_info_nhc() handles both, but returns a fib_nh_common
pointer instead of a fib_nh pointer. Luckily we only ever access fields
from the fib_nh_common parts, so we can just replace all instances of
fib_info_nh() with fib_info_nhc() and access the fields via their
fib_nh_common names.
This allows handling IPv4 routes with an external nexthop, and they now
get offloaded as expected:
$ ip route
10.0.0.0/24 dev swp5 proto kernel scope link src 10.0.0.1 rt_trap
10.0.1.0/24 nhid 20 via 10.0.0.2 dev swp5 offload rt_offload
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <[email protected]> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <[email protected]> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page).
Andrew Kanner [Thu, 3 Aug 2023 18:59:48 +0000 (20:59 +0200)]
drivers: net: prevent tun_build_skb() to exceed the packet size limit
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <[email protected]> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
Nilesh Javali [Mon, 7 Aug 2023 09:37:24 +0000 (15:07 +0530)]
scsi: qedf: Fix firmware halt over suspend and resume
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Nilesh Javali [Mon, 7 Aug 2023 09:37:25 +0000 (15:07 +0530)]
scsi: qedi: Fix firmware halt over suspend and resume
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Chengfeng Ye [Wed, 26 Jul 2023 12:56:55 +0000 (12:56 +0000)]
scsi: qedi: Fix potential deadlock on &qedi_percpu->p_work_lock
As &qedi_percpu->p_work_lock is acquired by hard IRQ qedi_msix_handler(),
other acquisitions of the same lock under process context should disable
IRQ, otherwise deadlock could happen if the IRQ preempts the execution
while the lock is held in process context on the same CPU.
qedi_cpu_offline() is one such function which acquires the lock in process
context.
Justin Tee [Thu, 3 Aug 2023 21:19:32 +0000 (14:19 -0700)]
scsi: lpfc: Remove reftag check in DIF paths
When preparing protection DIF I/O for DMA, the driver obtains reference
tags from scsi_prot_ref_tag(). Previously, there was a wrong assumption
that an all 0xffffffff value meant error and thus the driver failed the
I/O. This patch removes the evaluation code and accepts whatever the upper
layer returns.
Zhu Wang [Tue, 1 Aug 2023 11:14:21 +0000 (19:14 +0800)]
scsi: snic: Fix possible memory leak if device_add() fails
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to give up the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Zhu Wang [Thu, 3 Aug 2023 02:02:30 +0000 (10:02 +0800)]
scsi: core: Fix possible memory leak if device_add() fails
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to decrease the reference count in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Linus Torvalds [Tue, 8 Aug 2023 00:25:19 +0000 (17:25 -0700)]
Merge tag 'xsa432-6.5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen netback buffer overflow fix from Juergen Gross:
"The fix for XSA-423 added logic to Linux'es netback driver to deal
with a frontend splitting a packet in a way such that not all of the
headers would come in one piece.
Unfortunately the logic introduced there didn't account for the
extreme case of the entire packet being split into as many pieces as
permitted by the protocol, yet still being smaller than the area
that's specially dealt with to keep all (possible) headers together.
Such an unusual packet would therefore trigger a buffer overrun in the
driver"
* tag 'xsa432-6.5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/netback: Fix buffer overrun triggered by unusual packet
Linus Torvalds [Tue, 8 Aug 2023 00:03:54 +0000 (17:03 -0700)]
Merge tag 'gds-for-linus-2023-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/gds fixes from Dave Hansen:
"Mitigate Gather Data Sampling issue:
- Add Base GDS mitigation
- Support GDS_NO under KVM
- Fix a documentation typo"
* tag 'gds-for-linus-2023-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation/x86: Fix backwards on/off logic about YMM support
KVM: Add GDS_NO support to KVM
x86/speculation: Add Kconfig option for GDS
x86/speculation: Add force option to GDS mitigation
x86/speculation: Add Gather Data Sampling mitigation
Linus Torvalds [Mon, 7 Aug 2023 23:35:44 +0000 (16:35 -0700)]
Merge tag 'x86_bugs_srso' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/srso fixes from Borislav Petkov:
"Add a mitigation for the speculative RAS (Return Address Stack)
overflow vulnerability on AMD processors.
In short, this is yet another issue where userspace poisons a
microarchitectural structure which can then be used to leak privileged
information through a side channel"
* tag 'x86_bugs_srso' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/srso: Tie SBPB bit setting to microcode patch detection
x86/srso: Add a forgotten NOENDBR annotation
x86/srso: Fix return thunks in generated code
x86/srso: Add IBPB on VMEXIT
x86/srso: Add IBPB
x86/srso: Add SRSO_NO support
x86/srso: Add IBPB_BRTYPE support
x86/srso: Add a Speculative RAS Overflow mitigation
x86/bugs: Increase the x86 bugs vector size to two u32s
Linus Torvalds [Mon, 7 Aug 2023 20:07:12 +0000 (13:07 -0700)]
Merge tag 'wq-for-6.5-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
- The recently added cpu_intensive auto detection and warning mechanism
was spuriously triggered on slow CPUs.
While not causing serious issues, it's still a nuisance and can cause
unintended concurrency management behaviors.
Relax the threshold on machines with lower BogoMIPS. While BogoMIPS
is not an accurate measure of performance by most measures, we don't
have to be accurate and it has rough but strong enough correlation.
- A correction in Kconfig help text
* tag 'wq-for-6.5-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Scale up wq_cpu_intensive_thresh_us if BogoMIPS is below 4000
workqueue: Fix cpu_intensive_thresh_us name in help text
Linus Torvalds [Mon, 7 Aug 2023 20:03:36 +0000 (13:03 -0700)]
Merge tag 'tpmdd-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"A few more bug fixes"
* tag 'tpmdd-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm/tpm_tis: Disable interrupts for Lenovo P620 devices
tpm: Disable RNG for all AMD fTPMs
sysctl: set variable key_sysctls storage-class-specifier to static
tpm/tpm_tis: Disable interrupts for TUXEDO InfinityBook S 15/17 Gen7
Jakub Kicinski [Mon, 7 Aug 2023 19:26:58 +0000 (12:26 -0700)]
Merge branch 'wireguard-fixes-for-6-5-rc6'
Jason A. Donenfeld says:
====================
wireguard fixes for 6.5-rc6
Just one patch this time, somewhat late in the cycle:
1) Fix an off-by-one calculation for the maximum node depth size in the
allowedips trie data structure, and also adjust the self-tests to hit
this case so it doesn't regress again in the future.
====================
In the allowedips self-test, nodes are inserted into the tree, but it
generated an even amount of nodes, but for checking maximum node depth,
there is of course the root node, which makes the total number
necessarily odd. With two few nodes added, it never triggered the
maximum depth check like it should have. So, add 129 nodes instead of
128 nodes, and do so with a more straightforward scheme, starting with
all the bits set, and shifting over one each time. Then increase the
maximum depth to 129, and choose a better name for that variable to
make it clear that it represents depth as opposed to bits.
Ziyang Xuan [Wed, 2 Aug 2023 11:43:20 +0000 (19:43 +0800)]
bonding: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Lama Kayal [Sun, 11 Jun 2023 13:29:13 +0000 (16:29 +0300)]
net/mlx5e: Add capability check for vnic counters
Add missing capability check for each of the vnic counters exposed by
devlink health reporter, and thus avoid unexpected behavior due to
invalid access to registers.
While at it, read only the exact number of bits for each counter whether
it was 32 bits or 64 bits.
net/mlx5: Skip clock update work when device is in error state
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
action order 2: tunnel_key set
src_ip 192.168.1.25
dst_ip 192.168.1.26
key_id 4
dst_port 4789
csum pipe
index 3 ref 1 bind 1 installed 3807 sec used 3779 sec firstused 3800 sec
Action statistics:
Sent 120 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 3: mirred (Egress Redirect to device vxlan1) stolen
index 9 ref 1 bind 1 installed 3807 sec used 3779 sec firstused 3800 sec
Action statistics:
Sent 120 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
When handling FIB events, the rule in post act will not be deleted.
And because the post act rule has packet reformat and modify header
actions, also will hit the following syndromes:
mlx5_core 0000:08:00.0: mlx5_cmd_out_err:829:(pid 11613): DEALLOC_MODIFY_HEADER_CONTEXT(0x941) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1ab444), err(-22)
mlx5_core 0000:08:00.0: mlx5_cmd_out_err:829:(pid 11613): DEALLOC_PACKET_REFORMAT_CONTEXT(0x93e) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x179e84), err(-22)
Fix it by unoffloading post act rule when handling FIB events.
Daniel Jurgens [Mon, 10 Jul 2023 21:28:10 +0000 (00:28 +0300)]
net/mlx5: Allow 0 for total host VFs
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50beaf3 ("net/mlx5: Support querying max VFs from device"); Signed-off-by: Daniel Jurgens <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Daniel Jurgens [Mon, 26 Jun 2023 19:55:03 +0000 (22:55 +0300)]
net/mlx5: Return correct EC_VF function ID
The ECVF function ID range is 1..max_ec_vfs. Currently
mlx5_vport_to_func_id returns 0..max_ec_vfs - 1. Which
results in a syndrome when querying the caps with more
recent firmware, or reading incorrect caps with older
firmware that supports EC VFs.
Fixes: 9ac0b128248e ("net/mlx5: Update vport caps query/set for EC VFs") Signed-off-by: Daniel Jurgens <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
net/mlx5: DR, Fix wrong allocation of modify hdr pattern
Fixing wrong calculation of the modify hdr pattern size,
where the previously calculated number would not be enough
to accommodate the required number of actions.
Jianbo Liu [Fri, 14 Apr 2023 08:48:20 +0000 (08:48 +0000)]
net/mlx5e: TC, Fix internal port memory leak
The flow rule can be splited, and the extra post_act rules are added
to post_act table. It's possible to trigger memleak when the rule
forwards packets from internal port and over tunnel, in the case that,
for example, CT 'new' state offload is allowed. As int_port object is
assigned to the flow attribute of post_act rule, and its refcnt is
incremented by mlx5e_tc_int_port_get(), but mlx5e_tc_int_port_put() is
not called, the refcnt is never decremented, then int_port is never
freed.
Gal Pressman [Sun, 16 Jul 2023 11:28:10 +0000 (14:28 +0300)]
net/mlx5e: Take RTNL lock when needed before calling xdp_set_features()
Hold RTNL lock when calling xdp_set_features() with a registered netdev,
as the call triggers the netdev notifiers. This could happen when
switching from uplink rep to nic profile for example.
Hans de Goede [Sat, 5 Aug 2023 17:14:35 +0000 (19:14 +0200)]
ASoC: lower "no backend DAIs enabled for ... Port" log severity
If SNDRV_PCM_IOCTL_PREPARE is called when the mixer settings linking
frontend and backend have not been setup yet this results in
e.g. the following errors getting logged:
[ 43.244549] Baytrail Audio Port: ASoC: no backend DAIs enabled for Baytrail Audio Port
[ 43.244744] Baytrail Audio Port: ASoC: error at dpcm_fe_dai_prepare on Baytrail Audio Port: -22
pipewire triggers this leading to 96 lines getting logged
after the user has logged into a GNOME session.
Change the actual "no backend DAIs enabled for ... Port" error to
dev_err_once() to avoid it getting repeated 48 times. While at it
also improve the error by hinting the user how to fix this.
To not make developing new UCM profiles harder, also log the error
at dev_dbg() level all the time (vs once). So that e.g. dyndbg can
be used to (re)enable the messages.
Also changes _soc_pcm_ret() to not log for -EINVAL errors, to fix
the other error getting logged 48 times. Userspace passing wrong
parameters should not lead to dmesg messages.
Aleksa Sarai [Mon, 7 Aug 2023 02:24:15 +0000 (12:24 +1000)]
io_uring: correct check for O_TMPFILE
O_TMPFILE is actually __O_TMPFILE|O_DIRECTORY. This means that the old
check for whether RESOLVE_CACHED can be used would incorrectly think
that O_DIRECTORY could not be used with RESOLVE_CACHED.
tpm/tpm_tis: Disable interrupts for Lenovo P620 devices
The Lenovo ThinkStation P620 suffers from an irq storm issue like various
other Lenovo machines, so add an entry for it to tpm_tis_dmi_table and
force polling.
It is worth noting that 481c2d14627d (tpm,tpm_tis: Disable interrupts after
1000 unhandled IRQs) does not seem to fix the problem on this machine, but
setting 'tpm_tis.interrupts=0' on the kernel command line does.
The TPM RNG functionality is not necessary for entropy when the CPU
already supports the RDRAND instruction. The TPM RNG functionality
was previously disabled on a subset of AMD fTPM series, but reports
continue to show problems on some systems causing stutter root caused
to TPM RNG functionality.
Expand disabling TPM RNG use for all AMD fTPMs whether they have versions
that claim to have fixed or not. To accomplish this, move the detection
into part of the TPM CRB registration and add a flag indicating that
the TPM should opt-out of registration to hwrng.
Cc: [email protected] # 6.1.y+ Fixes: b006c439d58d ("hwrng: core - start hwrng kthread also for untrusted sources") Fixes: f1324bbc4011 ("tpm: disable hwrng for fTPM on some AMD designs") Reported-by: [email protected] Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217719 Reported-by: [email protected] Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217212 Signed-off-by: Mario Limonciello <[email protected]> Reviewed-by: Jarkko Sakkinen <[email protected]> Signed-off-by: Jarkko Sakkinen <[email protected]>
cpufreq: amd-pstate: fix global sysfs attribute type
In commit 3666062b87ec ("cpufreq: amd-pstate: move to use bus_get_dev_root()")
the "amd_pstate" attributes where moved from a dedicated kobject to the
cpu root kobject.
While the dedicated kobject expects to contain kobj_attributes the root
kobject needs device_attributes.
As the changed arguments are not used by the callbacks it works most of
the time.
However CFI will detect this issue:
Linus Torvalds [Mon, 7 Aug 2023 17:18:20 +0000 (10:18 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"x86:
- Fix SEV race condition
ARM:
- Fixes for the configuration of SVE/SME traps when hVHE mode is in
use
- Allow use of pKVM on systems with FF-A implementations that are
v1.0 compatible
- Request/release percpu IRQs (arch timer, vGIC maintenance)
correctly when pKVM is in use
- Fix function prototype after __kvm_host_psci_cpu_entry() rename
- Skip to the next instruction when emulating writes to TCR_EL1 on
AmpereOne systems
Selftests:
- Fix missing include"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
selftests/rseq: Fix build with undefined __weak
KVM: SEV: remove ghcb variable declarations
KVM: SEV: only access GHCB fields once
KVM: SEV: snapshot the GHCB before accessing it
KVM: arm64: Skip instruction after emulating write to TCR_EL1
KVM: arm64: fix __kvm_host_psci_cpu_entry() prototype
KVM: arm64: Fix resetting SME trap values on reset for (h)VHE
KVM: arm64: Fix resetting SVE trap values on reset for hVHE
KVM: arm64: Use the appropriate feature trap register when activating traps
KVM: arm64: Helper to write to appropriate feature trap register based on mode
KVM: arm64: Disable SME traps for (h)VHE at setup
KVM: arm64: Use the appropriate feature trap register for SVE at EL2 setup
KVM: arm64: Factor out code for checking (h)VHE mode into a macro
KVM: arm64: Rephrase percpu enable/disable tracking in terms of hyp
KVM: arm64: Fix hardware enable/disable flows for pKVM
KVM: arm64: Allow pKVM on v1.0 compatible FF-A implementations
Linus Torvalds [Mon, 7 Aug 2023 17:08:55 +0000 (10:08 -0700)]
Merge tag 'mmc-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- moxart: Fix big-endian conversion for SCR structure
- sdhci-f-sdh30: Replace with sdhci_pltfm to fix PM support
* tag 'mmc-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-f-sdh30: Replace with sdhci_pltfm
mmc: moxart: read scr register without changing byte order
Bob Peterson [Wed, 2 Aug 2023 14:24:12 +0000 (09:24 -0500)]
gfs2: Don't use filemap_splice_read
Starting with patch 2cb1e08985, gfs2 started using the new function
filemap_splice_read rather than the old (and subsequently deleted)
function generic_file_splice_read.
filemap_splice_read works by taking references to a number of folios in
the page cache and splicing those folios into a pipe. The folios are
then read from the pipe and the folio references are dropped. This can
take an arbitrary amount of time. We cannot allow that in gfs2 because
those folio references will pin the inode glock to the node and prevent
it from being demoted, which can lead to cluster-wide deadlocks.
Instead, use copy_splice_read.
(In addition, the old generic_file_splice_read called into ->read_iter,
which called gfs2_file_read_iter, which took the inode glock during the
operation. The new filemap_splice_read interface does not take the
inode glock anymore. This is fixable, but it still wouldn't prevent
cluster-wide deadlocks.)
Fixes: 2cb1e08985e3 ("splice: Use filemap_splice_read() instead of generic_file_splice_read()") Signed-off-by: Bob Peterson <[email protected]> Signed-off-by: Andreas Gruenbacher <[email protected]>
gfs2: Fix freeze consistency check in gfs2_trans_add_meta
Function gfs2_trans_add_meta() checks for the SDF_FROZEN flag to make
sure that no buffers are added to a transaction while the filesystem is
frozen. With the recent freeze/thaw rework, the SDF_FROZEN flag is
cleared after thaw_super() is called, which is sufficient for
serializing freeze/thaw.
However, other filesystem operations started after thaw_super() may now
be calling gfs2_trans_add_meta() before the SDF_FROZEN flag is cleared,
which will trigger the SDF_FROZEN check in gfs2_trans_add_meta(). Fix
that by checking the s_writers.frozen state instead.
In addition, make sure not to call gfs2_assert_withdraw() with the
sd_log_lock spin lock held. Check for a withdrawn filesystem before
checking for a frozen filesystem, and don't pin/add buffers to the
current transaction in case of a failure in either case.
x86/sev: Do not try to parse for the CC blob on non-AMD hardware
Tao Liu reported a boot hang on an Intel Atom machine due to an unmapped
EFI config table. The reason being that the CC blob which contains the
CPUID page for AMD SNP guests is parsed for before even checking
whether the machine runs on AMD hardware.
Usually that's not a problem on !AMD hw - it simply won't find the CC
blob's GUID and return. However, if any parts of the config table
pointers array is not mapped, the kernel will #PF very early in the
decompressor stage without any opportunity to recover.
Therefore, do a superficial CPUID check before poking for the CC blob.
This will fix the current issue on real hardware. It would also work as
a guest on a non-lying hypervisor.
For the lying hypervisor, the check is done again, *after* parsing the
CC blob as the real CPUID page will be present then.
Clear the #VC handler in case SEV-{ES,SNP} hasn't been detected, as
a precaution.
Vlastimil Babka [Mon, 7 Aug 2023 08:33:57 +0000 (10:33 +0200)]
PM: hibernate: fix resume_store() return value when hibernation not available
On a laptop with hibernation set up but not actively used, and with
secure boot and lockdown enabled kernel, 6.5-rc1 gets stuck on boot with
the following repeated messages:
A start job is running for Resume from hibernation using device /dev/system/swap (24s / no limit)
lockdown_is_locked_down: 25311154 callbacks suppressed
Lockdown: systemd-hiberna: hibernation is restricted; see man kernel_lockdown.7
...
Checking the resume code leads to commit cc89c63e2fe3 ("PM: hibernate:
move finding the resume device out of software_resume") which
inadvertently changed the return value from resume_store() to 0 when
!hibernation_available(). This apparently translates to userspace
write() returning 0 as in number of bytes written, and userspace looping
indefinitely in the attempt to write the intended value.
Fix this by returning the full number of bytes that were to be written,
as that's what was done before the commit.
Fixes: cc89c63e2fe3 ("PM: hibernate: move finding the resume device out of software_resume") Signed-off-by: Vlastimil Babka <[email protected]> Reviewed-by: Christoph Hellwig <[email protected]> Acked-by: Greg Kroah-Hartman <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
x86/srso: Tie SBPB bit setting to microcode patch detection
The SBPB bit in MSR_IA32_PRED_CMD is supported only after a microcode
patch has been applied so set X86_FEATURE_SBPB only then. Otherwise,
guests would attempt to set that bit and #GP on the MSR write.
While at it, make SMT detection more robust as some guests - depending
on how and what CPUID leafs their report - lead to cpu_smt_control
getting set to CPU_SMT_NOT_SUPPORTED but SRSO_NO should be set for any
guest incarnation where one simply cannot do SMT, for whatever reason.
A couple of hardware registers need to be set to reflect which
interrupts have been allocated to the device. Each register is 32-bit
wide and can receive four 8-bit values. If we provide any other interrupt
number than four, the irq_num variable will never be 0 within the while
check and the while block will loop forever.
There is an easy way to prevent this: just break the for loop
when we reach "irq_num == 0", which anyway means all interrupts have
been processed.
dmaengine: owl-dma: Modify mismatched function name
No functional modification involved.
drivers/dma/owl-dma.c:208: warning: expecting prototype for struct owl_dma_pchan. Prototype was for struct owl_dma_vchan instead HDRTEST usr/include/sound/asequencer.h
dmaengine: idxd: Clear PRS disable flag when disabling IDXD device
Disabling IDXD device doesn't reset Page Request Service (PRS)
disable flag to its initial value 0. This may cause user confusion
because once PRS is disabled user will see PRS still remains the
previous setting (i.e. disabled) via sysfs interface even after the
device is disabled.
To eliminate user confusion, reset PRS disable flag to ensure that
the PRS flag bit reflects correct state after the device is disabled.
Additionally, simplify the code by setting wq->flags to 0, which clears
all flag bits, including any future additions.
Ilpo Järvinen [Fri, 26 May 2023 10:54:34 +0000 (13:54 +0300)]
dmaengine: pl330: Return DMA_PAUSED when transaction is paused
pl330_pause() does not set anything to indicate paused condition which
causes pl330_tx_status() to return DMA_IN_PROGRESS. This breaks 8250
DMA flush after the fix in commit 57e9af7831dc ("serial: 8250_dma: Fix
DMA Rx rearm race"). The function comment for pl330_pause() claims
pause is supported but resume is not which is enough for 8250 DMA flush
to work as long as DMA status reports DMA_PAUSED when appropriate.
Add PAUSED state for descriptor and mark BUSY descriptors with PAUSED
in pl330_pause(). Return DMA_PAUSED from pl330_tx_status() when the
descriptor is PAUSED.
dmaengine: mcf-edma: Fix a potential un-allocated memory access
When 'mcf_edma' is allocated, some space is allocated for a
flexible array at the end of the struct. 'chans' item are allocated, that is
to say 'pdata->dma_channels'.
Then, this number of item is stored in 'mcf_edma->n_chans'.
A few lines later, if 'mcf_edma->n_chans' is 0, then a default value of 64
is set.
This ends to no space allocated by devm_kzalloc() because chans was 0, but
64 items are read and/or written in some not allocated memory.
Change the logic to define a default value before allocating the memory.
Linus Torvalds [Sun, 6 Aug 2023 17:43:52 +0000 (10:43 -0700)]
Merge tag 'v6.5-rc5.vfs.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Fix a wrong check for O_TMPFILE during RESOLVE_CACHED lookup
- Clean up directory iterators and clarify file_needs_f_pos_lock()
* tag 'v6.5-rc5.vfs.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: rely on ->iterate_shared to determine f_pos locking
vfs: get rid of old '->iterate' directory operation
proc: fix missing conversion to 'iterate_shared'
open: make RESOLVE_CACHED correctly test for O_TMPFILE
Nitya Sunkad [Fri, 4 Aug 2023 20:56:22 +0000 (13:56 -0700)]
ionic: Add missing err handling for queue reconfig
ionic_start_queues_reconfig returns an error code if txrx_init fails.
Handle this error code in the relevant places.
This fixes a corner case where the device could get left in a detached
state if the CMB reconfig fails and the attempt to clean up the mess
also fails. Note that calling netif_device_attach when the netdev is
already attached does not lead to unexpected behavior.
Change goto name "errout" to "err_out" to maintain consistency across
goto statements.
Fixes: 40bc471dc714 ("ionic: add tx/rx-push support with device Component Memory Buffers") Fixes: 6f7d6f0fd7a3 ("ionic: pull reset_queues into tx_timeout handler") Signed-off-by: Nitya Sunkad <[email protected]> Signed-off-by: Shannon Nelson <[email protected]> Signed-off-by: David S. Miller <[email protected]>
fs: rely on ->iterate_shared to determine f_pos locking
Now that we removed ->iterate we don't need to check for either
->iterate or ->iterate_shared in file_needs_f_pos_lock(). Simply check
for ->iterate_shared instead. This will tell us whether we need to
unconditionally take the lock. Not just does it allow us to avoid
checking f_inode's mode it also actually clearly shows that we're
locking because of readdir.
Linus Torvalds [Sat, 5 Aug 2023 19:25:01 +0000 (12:25 -0700)]
vfs: get rid of old '->iterate' directory operation
All users now just use '->iterate_shared()', which only takes the
directory inode lock for reading.
Filesystems that never got convered to shared mode now instead use a
wrapper that drops the lock, re-takes it in write mode, calls the old
function, and then downgrades the lock back to read mode.
This way the VFS layer and other callers no longer need to care about
filesystems that never got converted to the modern era.
The filesystems that use the new wrapper are ceph, coda, exfat, jfs,
ntfs, ocfs2, overlayfs, and vboxsf.
Honestly, several of them look like they really could just iterate their
directories in shared mode and skip the wrapper entirely, but the point
of this change is to not change semantics or fix filesystems that
haven't been fixed in the last 7+ years, but to finally get rid of the
dual iterators.
Linus Torvalds [Sat, 5 Aug 2023 17:49:31 +0000 (10:49 -0700)]
proc: fix missing conversion to 'iterate_shared'
I'm looking at the directory handling due to the discussion about f_pos
locking (see commit 797964253d35: "file: reinstate f_pos locking
optimization for regular files"), and wanting to clean that up.
And one source of ugliness is how we were supposed to move filesystems
over to the '->iterate_shared()' function that only takes the inode lock
for reading many many years ago, but several filesystems still use the
bad old '->iterate()' that takes the inode lock for exclusive access.
See commit 6192269444eb ("introduce a parallel variant of ->iterate()")
that also added some documentation stating
Old method is only used if the new one is absent; eventually it will
be removed. Switch while you still can; the old one won't stay.
and that was back in April 2016. Here we are, many years later, and the
old version is still clearly sadly alive and well.
Now, some of those old style iterators are probably just because the
filesystem may end up having per-inode mutable data that it uses for
iterating a directory, but at least one case is just a mistake.
Al switched over most filesystems to use '->iterate_shared()' back when
it was introduced. In particular, the /proc filesystem was converted as
one of the first ones in commit f50752eaa0b0 ("switch all procfs
directories ->iterate_shared()").
But then later one new user of '->iterate()' was then re-introduced by
commit 6d9c939dbe4d ("procfs: add smack subdir to attrs").
And that's clearly not what we wanted, since that new case just uses the
same 'proc_pident_readdir()' and 'proc_pident_lookup()' helper functions
that other /proc pident directories use, and they are most definitely
safe to use with the inode lock held shared.
So just fix it.
This still leaves a fair number of oddball filesystems using the
old-style directory iterator (ceph, coda, exfat, jfs, ntfs, ocfs2,
overlayfs, and vboxsf), but at least we don't have any remaining in the
core filesystems.
I'm going to add a wrapper function that just drops the read-lock and
takes it as a write lock, so that we can clean up the core vfs layer and
make all the ugly 'this filesystem needs exclusive inode locking' be
just filesystem-internal warts.
I just didn't want to make that conversion when we still had a core user
left.
Aleksa Sarai [Sat, 5 Aug 2023 16:11:58 +0000 (02:11 +1000)]
open: make RESOLVE_CACHED correctly test for O_TMPFILE
O_TMPFILE is actually __O_TMPFILE|O_DIRECTORY. This means that the old
fast-path check for RESOLVE_CACHED would reject all users passing
O_DIRECTORY with -EAGAIN, when in fact the intended test was to check
for __O_TMPFILE.
Jakub Kicinski [Fri, 4 Aug 2023 22:59:51 +0000 (15:59 -0700)]
net: tls: avoid discarding data on record close
TLS records end with a 16B tag. For TLS device offload we only
need to make space for this tag in the stream, the device will
generate and replace it with the actual calculated tag.
Long time ago the code would just re-reference the head frag
which mostly worked but was suboptimal because it prevented TCP
from combining the record into a single skb frag. I'm not sure
if it was correct as the first frag may be shorter than the tag.
The commit under fixes tried to replace that with using the page
frag and if the allocation failed rolling back the data, if record
was long enough. It achieves better fragment coalescing but is
also buggy.
We don't roll back the iterator, so unless we're at the end of
send we'll skip the data we designated as tag and start the
next record as if the rollback never happened.
There's also the possibility that the record was constructed
with MSG_MORE and the data came from a different syscall and
we already told the user space that we "got it".
Allocate a single dummy page and use it as fallback.
Found by code inspection, and proven by forcing allocation
failures.
Fixes: e7b159a48ba6 ("net/tls: remove the record tail optimization") Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Alexander Stein [Fri, 28 Jul 2023 08:34:35 +0000 (10:34 +0200)]
arm64: dts: imx93: Fix anatop node size
Although the memory map of i.MX93 reference manual rev. 2 claims that
analog top has start address of 0x44480000 and end address of 0x4448ffff,
this overlaps with TMU memory area starting at 0x44482000, as stated in
section 73.6.1.
As PLL configuration registers start at addresses up to 0x44481400, as used
by clk-imx93, reduce the anatop size to 0x2000, so exclude the TMU area
but keep all PLL registers inside.
Namjae Jeon [Sat, 5 Aug 2023 23:44:17 +0000 (08:44 +0900)]
ksmbd: fix wrong next length validation of ea buffer in smb2_set_ea()
There are multiple smb2_ea_info buffers in FILE_FULL_EA_INFORMATION request
from client. ksmbd find next smb2_ea_info using ->NextEntryOffset of
current smb2_ea_info. ksmbd need to validate buffer length Before
accessing the next ea. ksmbd should check buffer length using buf_len,
not next variable. next is the start offset of current ea that got from
previous ea.
Long Li [Sat, 29 Jul 2023 03:36:18 +0000 (11:36 +0800)]
ksmbd: validate command request size
In commit 2b9b8f3b68ed ("ksmbd: validate command payload size"), except
for SMB2_OPLOCK_BREAK_HE command, the request size of other commands
is not checked, it's not expected. Fix it by add check for request
size of other commands.
Linus Torvalds [Sun, 6 Aug 2023 01:45:18 +0000 (18:45 -0700)]
Merge tag 'ata-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
- Prevent the scsi disk driver from issuing a START STOP UNIT command
for ATA devices during system resume as this causes various issues
reported by multiple users.
* tag 'ata-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata,scsi: do not issue START STOP UNIT on resume
zram: take device and not only bvec offset into account
Commit af8b04c63708 ("zram: simplify bvec iteration in
__zram_make_request") changed the bio iteration in zram to rely on the
implicit capping to page boundaries in bio_for_each_segment. But it
failed to care for the fact zram not only care about the page alignment
of the bio payload, but also the page alignment into the device. For
buffered I/O and swap those are the same, but for direct I/O or kernel
internal I/O like XFS log buffer writes they can differ.
Fix this by open coding bio_for_each_segment and limiting the bvec len
so that it never crosses over a page alignment boundary in the device
in addition to the payload boundary already taken care of by
bio_iter_iovec.
Linus Torvalds [Sat, 5 Aug 2023 20:16:17 +0000 (13:16 -0700)]
Merge tag 'powerpc-6.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix vmemmap altmap boundary check which could cause memory hotunplug
failure
- Create a dummy stackframe to fix ftrace stack unwind
- Fix secondary thread bringup for Book3E ELFv2 kernels
- Use early_ioremap/unmap() in via_calibrate_decr()
Thanks to Aneesh Kumar K.V, Benjamin Gray, Christophe Leroy, David
Hildenbrand, and Naveen N Rao.
* tag 'powerpc-6.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powermac: Use early_* IO variants in via_calibrate_decr()
powerpc/64e: Fix secondary thread bringup for ELFv2 kernels
powerpc/ftrace: Create a dummy stackframe to fix stack unwind
powerpc/mm/altmap: Fix altmap boundary check
Linus Torvalds [Sat, 5 Aug 2023 20:09:05 +0000 (13:09 -0700)]
Merge tag 'parisc-for-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- early fixmap preallocation to fix boot failures on kernel >= 6.4
- remove DMA leftover code in parport_gsc
- drop old comments and code style fixes
* tag 'parisc-for-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: unaligned: Add required spaces after ','
parport: gsc: remove DMA leftover code
parisc: pci-dma: remove unused and dead EISA code and comment
parisc/mm: preallocate fixmap page tables at init
Merge tag 'icc-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Georgi writes:
interconnect fixes for v6.5-rc
This contains a fix for a potential issue on some Qualcomm SoCs where
bit-masks should have been used to configure the Bus Clock Manager
hardware, instead of bandwidth units.
- interconnect: qcom: Add support for mask-based BCMs
- interconnect: qcom: sm8450: add enable_mask for bcm nodes
- interconnect: qcom: sm8550: add enable_mask for bcm nodes
- interconnect: qcom: sa8775p: add enable_mask for bcm nodes
Signed-off-by: Georgi Djakov <[email protected]>
* tag 'icc-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: qcom: sa8775p: add enable_mask for bcm nodes
interconnect: qcom: sm8550: add enable_mask for bcm nodes
interconnect: qcom: sm8450: add enable_mask for bcm nodes
interconnect: qcom: Add support for mask-based BCMs
Linus Torvalds [Sat, 5 Aug 2023 02:35:09 +0000 (19:35 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few clk driver fixes for some SoC clk drivers:
- Change a usleep() to udelay() to avoid scheduling while atomic in
the Amlogic PLL code
- Revert a patch to the Mediatek MT8183 driver that caused an
out-of-bounds write
- Return the right error value when devm_of_iomap() fails in
imx93_clocks_probe()
- Constrain the Kconfig for the fixed mmio clk so that it depends on
HAS_IOMEM and can't be compiled on architectures such as s390"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: fixed-mmio: make COMMON_CLK_FIXED_MMIO depend on HAS_IOMEM
clk: imx93: Propagate correct error in imx93_clocks_probe()
clk: mediatek: mt8183: Add back SSPM related clocks
clk: meson: change usleep_range() to udelay() for atomic context
Jakub Kicinski [Sat, 5 Aug 2023 01:26:29 +0000 (18:26 -0700)]
Merge branch 'mptcp-more-fixes-for-v6-5'
Matthieu Baerts says:
====================
mptcp: more fixes for v6.5
Here is a new batch of fixes related to MPTCP for v6.5 and older.
Patches 1 and 2 fix issues with MPTCP Join selftest when manually
launched with '-i' parameter to use 'ip mptcp' tool instead of the
dedicated one (pm_nl_ctl). The issues have been there since v5.18.
Thank you Andrea for your first contributions to MPTCP code in the
upstream kernel!
Patch 3 avoids corrupting the data stream when trying to reset
connections that have fallen back to TCP. This can happen from v6.1.
Patch 4 fixes a race when doing a disconnect() and an accept() in
parallel on a listener socket. The issue only happens in rare cases if
the user is really unlucky since a fix that landed in v6.3 but
backported up to v6.1.
====================
Paolo Abeni [Thu, 3 Aug 2023 16:27:30 +0000 (18:27 +0200)]
mptcp: fix disconnect vs accept race
Despite commit 0ad529d9fd2b ("mptcp: fix possible divide by zero in
recvmsg()"), the mptcp protocol is still prone to a race between
disconnect() (or shutdown) and accept.
The root cause is that the mentioned commit checks the msk-level
flag, but mptcp_stream_accept() does acquire the msk-level lock,
as it can rely directly on the first subflow lock.
As reported by Christoph than can lead to a race where an msk
socket is accepted after that mptcp_subflow_queue_clean() releases
the listener socket lock and just before it takes destructive
actions leading to the following splat:
Address the issue by temporary removing the pending request socket
from the accept queue, so that racing accept() can't touch them.
After depleting the msk - the ssk still exists, as plain TCP sockets,
re-insert them into the accept queue, so that later inet_csk_listen_stop()
will complete the tcp socket disposal.
Paolo Abeni [Thu, 3 Aug 2023 16:27:29 +0000 (18:27 +0200)]
mptcp: avoid bogus reset on fallback close
Since the blamed commit, the MPTCP protocol unconditionally sends
TCP resets on all the subflows on disconnect().
That fits full-blown MPTCP sockets - to implement the fastclose
mechanism - but causes unexpected corruption of the data stream,
caught as sporadic self-tests failures.
Andrea Claudi [Thu, 3 Aug 2023 16:27:28 +0000 (18:27 +0200)]
selftests: mptcp: join: fix 'implicit EP' test
mptcp_join 'implicit EP' test currently fails when using ip mptcp:
$ ./mptcp_join.sh -iI
<snip>
001 implicit EP creation[fail] expected '10.0.2.2 10.0.2.2 id 1 implicit' found '10.0.2.2 id 1 rawflags 10 '
Error: too many addresses or duplicate one: -22.
ID change is prevented[fail] expected '10.0.2.2 10.0.2.2 id 1 implicit' found '10.0.2.2 id 1 rawflags 10 '
modif is allowed[fail] expected '10.0.2.2 10.0.2.2 id 1 signal' found '10.0.2.2 id 1 signal '
This happens because of two reasons:
- iproute v6.3.0 does not support the implicit flag, fixed with
iproute2-next commit 3a2535a41854 ("mptcp: add support for implicit
flag")
- pm_nl_check_endpoint wrongly expects the ip address to be repeated two
times in iproute output, and does not account for a final whitespace
in it.
This fixes the issue trimming the whitespace in the output string and
removing the double address in the expected string.
Andrea Claudi [Thu, 3 Aug 2023 16:27:27 +0000 (18:27 +0200)]
selftests: mptcp: join: fix 'delete and re-add' test
mptcp_join 'delete and re-add' test fails when using ip mptcp:
$ ./mptcp_join.sh -iI
<snip>
002 delete and re-add before delete[ ok ]
mptcp_info subflows=1 [ ok ]
Error: argument "ADDRESS" is wrong: invalid for non-zero id address
after delete[fail] got 2:2 subflows expected 1
This happens because endpoint delete includes an ip address while id is
not 0, contrary to what is indicated in the ip mptcp man page:
"When used with the delete id operation, an IFADDR is only included when
the ID is 0."
This fixes the issue using the $addr variable in pm_nl_del_endpoint()
only when id is 0.
selftests: net: test vxlan pmtu exceptions with tcp
TCP might get stuck if a nonlinear skb exceeds the path MTU,
icmp error contains an incorrect icmp checksum in that case.
Extend the existing test for vxlan to also send at least 1MB worth of
data via TCP in addition to the existing 'large icmp packet adds
route exception'.
On my test VM this fails due to 0-size output file without
"tunnels: fix kasan splat when generating ipv4 pmtu error".
projects / linux.git / log