Git Repo - linux.git/log

net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled

The blamed commit made the fatally incorrect assumption that ports which
aren't in the FORWARDING STP state should not have packets forwarded
towards them, and that is all that needs to be done.

However, that logic alone permits BLOCKING ports to forward to
FORWARDING ports, which of course allows packet storms to occur when
there is an L2 loop.

The ocelot_get_bridge_fwd_mask should not only ask "what can the bridge
do for you", but "what can you do for the bridge". This way, only
FORWARDING ports forward to the other FORWARDING ports from the same
bridging domain, and we are still compatible with the idea of multiple
bridges.

Fixes: df291e54ccca ("net: ocelot: support multiple bridges")
Suggested-by: Colin Foster <colin.foster@in-advantage.com>
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: mtk_eth_soc: avoid creating duplicate offload entries

Sometimes multiple CLS_REPLACE calls are issued for the same connection.
rhashtable_insert_fast does not check for these duplicates, so multiple
hardware flow entries can be created.
Fix this by checking for an existing entry early

Fixes: 502e84e2382d ("net: ethernet: mtk_eth_soc: add flow offloading support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfc: st-nci: Add SPI ID matching DT compatible

Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding the part name used in
the compatible to the list of SPI IDs.

Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: remove Guvenc Gulce as net/smc maintainer

Remove myself as net/smc maintainer, as I am
leaving IBM soon and can not maintain net/smc anymore.

Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nexthop: Fix memory leaks in nexthop notification chain listeners

syzkaller discovered memory leaks [1] that can be reduced to the
following commands:

# ip nexthop add id 1 blackhole
# devlink dev reload pci/0000:06:00.0

As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.

One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.

Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.

The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.

[1]
unreferenced object 0xffff88806173d600 (size 512):
  comm "syz-executor.0", pid 1290, jiffies 4295583142 (age 143.507s)
  hex dump (first 32 bytes):
    41 9d 1e 60 80 88 ff ff 08 d6 73 61 80 88 ff ff  A..`......sa....
    08 d6 73 61 80 88 ff ff 01 00 00 00 00 00 00 00  ..sa............
  backtrace:
    [<ffffffff81a6b576>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
    [<ffffffff81a6b576>] slab_post_alloc_hook+0x96/0x490 mm/slab.h:522
    [<ffffffff81a716d3>] slab_alloc_node mm/slub.c:3206 [inline]
    [<ffffffff81a716d3>] slab_alloc mm/slub.c:3214 [inline]
    [<ffffffff81a716d3>] kmem_cache_alloc_trace+0x163/0x370 mm/slub.c:3231
    [<ffffffff82e8681a>] kmalloc include/linux/slab.h:591 [inline]
    [<ffffffff82e8681a>] kzalloc include/linux/slab.h:721 [inline]
    [<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_group_create drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4918 [inline]
    [<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_new drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5054 [inline]
    [<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_event+0x59a/0x2910 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5239
    [<ffffffff813ef67d>] notifier_call_chain+0xbd/0x210 kernel/notifier.c:83
    [<ffffffff813f0662>] blocking_notifier_call_chain kernel/notifier.c:318 [inline]
    [<ffffffff813f0662>] blocking_notifier_call_chain+0x72/0xa0 kernel/notifier.c:306
    [<ffffffff8384b9c6>] call_nexthop_notifiers+0x156/0x310 net/ipv4/nexthop.c:244
    [<ffffffff83852bd8>] insert_nexthop net/ipv4/nexthop.c:2336 [inline]
    [<ffffffff83852bd8>] nexthop_add net/ipv4/nexthop.c:2644 [inline]
    [<ffffffff83852bd8>] rtm_new_nexthop+0x14e8/0x4d10 net/ipv4/nexthop.c:2913
    [<ffffffff833e9a78>] rtnetlink_rcv_msg+0x448/0xbf0 net/core/rtnetlink.c:5572
    [<ffffffff83608703>] netlink_rcv_skb+0x173/0x480 net/netlink/af_netlink.c:2504
    [<ffffffff833de032>] rtnetlink_rcv+0x22/0x30 net/core/rtnetlink.c:5590
    [<ffffffff836069de>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
    [<ffffffff836069de>] netlink_unicast+0x5ae/0x7f0 net/netlink/af_netlink.c:1340
    [<ffffffff83607501>] netlink_sendmsg+0x8e1/0xe30 net/netlink/af_netlink.c:1929
    [<ffffffff832fde84>] sock_sendmsg_nosec net/socket.c:704 [inline]
    [<ffffffff832fde84>] sock_sendmsg net/socket.c:724 [inline]
    [<ffffffff832fde84>] ____sys_sendmsg+0x874/0x9f0 net/socket.c:2409
    [<ffffffff83304a44>] ___sys_sendmsg+0x104/0x170 net/socket.c:2463
    [<ffffffff83304c01>] __sys_sendmsg+0x111/0x1f0 net/socket.c:2492
    [<ffffffff83304d5d>] __do_sys_sendmsg net/socket.c:2501 [inline]
    [<ffffffff83304d5d>] __se_sys_sendmsg net/socket.c:2499 [inline]
    [<ffffffff83304d5d>] __x64_sys_sendmsg+0x7d/0xc0 net/socket.c:2499

Fixes: 2a014b200bbd ("mlxsw: spectrum_router: Add support for nexthop objects")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

posix-cpu-timers: Prevent spuriously armed 0-value itimer

Resetting/stopping an itimer eventually leads to it being reprogrammed
with an actual "0" value. As a result the itimer expires on the next
tick, triggering an unexpected signal.

To fix this, make sure that
struct signal_struct::it[CPUCLOCK_PROF/VIRT]::expires is set to 0 when
setitimer() passes a 0 it_value, indicating that the timer must stop.

Fixes: 406dd42bd1ba ("posix-cpu-timers: Force next expiration recalc after itimer reset")
Reported-by: Victor Stinner <vstinner@redhat.com>
Reported-by: Chris Hixon <linux-kernel-bugs@hixontech.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210913145332.232023-1-frederic@kernel.org

USB: serial: cp210x: add part-number debug printk

Add a part-number debug printk to facilitate debugging.

Signed-off-by: Johan Hovold <johan@kernel.org>

USB: serial: cp210x: fix dropped characters with CP2102

Some CP2102 do not support event-insertion mode but return no error when
attempting to enable it.

This means that any event escape characters in the input stream will not
be escaped by the device and consequently regular data may be
interpreted as escape sequences and be removed from the stream by the
driver.

The reporter's device has batch number DCL00X etched into it and as
discovered by the SHA2017 Badge team, counterfeit devices with that
marking can be detected by sending malformed vendor requests. [1][2]

Tests confirm that the possibly counterfeit CP2102 returns a single byte
in response to a malformed two-byte part-number request, while an
original CP2102 returns two bytes. Assume that every CP2102 that behaves
this way also does not support event-insertion mode (e.g. cannot report
parity errors).

[1] https://mobile.twitter.com/sha2017badge/status/1167902087289532418
[2] https://hackaday.com/2017/08/14/hands-on-with-the-shacamp-2017-badge/#comment-3903376

Reported-by: Malte Di Donato <malte@neo-soft.org>
Tested-by: Malte Di Donato <malte@neo-soft.org>
Fixes: a7207e9835a4 ("USB: serial: cp210x: add support for line-status events")
Cc: stable@vger.kernel.org # 5.9
Link: https://lore.kernel.org/r/20210922113100.20888-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

ksmbd: remove follow symlinks support

Use LOOKUP_NO_SYMLINKS flags for default lookup to prohibit the middle of
symlink component lookup and remove follow symlinks parameter support.
We re-implement it as reparse point later.

Test result:
smbclient -Ulinkinjeon%1234 //172.30.1.42/share -c
"get hacked/passwd passwd"
NT_STATUS_OBJECT_NAME_NOT_FOUND opening remote file \hacked\passwd

Cc: Ralph Böhme <slow@samba.org>
Cc: Steve French <smfrench@gmail.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

ksmbd: check protocol id in ksmbd_verify_smb_message()

When second smb2 pdu has invalid protocol id, ksmbd doesn't detect it
and allow to process smb2 request. This patch add the check it in
ksmbd_verify_smb_message() and don't use protocol id of smb2 request as
protocol id of response.

Reviewed-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Reviewed-by: Ralph Böhme <slow@samba.org>
Reported-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>

init: Revert accidental changes to print irqs_disabled()

Commit f8ade8dddb16 ("xsurf100: drop include of lib8390.c") accidentally
changed init/main.c. Revert that part.

Fixes: f8ade8dddb16 ("xsurf100: drop include of lib8390.c")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: Update Xen-[PCI,SWIOTLB,Block] maintainership

Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Juergen, Roger, and Stefano.

Thank you!

Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: Update SWIOTLB maintainership

Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Christoph Hellwig.

Thank you!

Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: update entry for NIOS2

Ley Foon has left Intel and will no longer be able to maintain NIOS2.
Update the MAINTAINER's entry to Dinh Nguyen.

Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi modalias fix from Mark Brown:
"Fix modalias issues

  As reported by Russell King the change to use OF style modaliases for
  DT enumerated broke at least the spi-nor driver, the patch here
  reverts that change to fix the regression.

  Sadly this will mean that anything that started loading since the
  change to OF modaliases will run into issues, there doesn't seem to be
  any approach which doesn't cause some problems and thi seems like the
  least bad approach - gory details are in the commit log for the
  change.

  I'm currently working through the SPI drivers to add ID tables and
  missing IDs to tables which should address things from the other end,
  this seems more straightforward and robust than any other options"

* tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: Revert modalias changes

Merge branch 'md-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md into block-5.15

Pull MD fix from Song.

* 'md-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md: fix a lock order reversal in md_alloc

x86/asm: Fix SETZ size enqcmds() build failure

When building under GCC 4.9 and 5.5:

arch/x86/include/asm/special_insns.h: Assembler messages:
arch/x86/include/asm/special_insns.h:286: Error: operand size mismatch for `setz'

Change the type to "bool" for condition code arguments, as documented.

Fixes: 7f5933f81bd8 ("x86/asm: Add an enqcmds() wrapper for the ENQCMDS instruction")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20210910223332.3224851-1-keescook@chromium.org

Merge tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux

Pull nfsd fixes from Chuck Lever:
"Critical bug fixes:

   - Fix crash in NLM TEST procedure

   - NFSv4.1+ backchannel not restored after PATH_DOWN"

* tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  nfsd: back channel stuck in SEQ4_STATUS_CB_PATH_DOWN
  NLM: Fix svcxdr_encode_owner()

Merge tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Hans de Goede:
"The first round of bug-fixes for platform-drivers-x86 for 5.15,
  highlights:

   - amd-pmc fix for some suspend/resume issues

   - intel-hid fix to avoid false-positive SW_TABLET_MODE=1 reporting

   - some build error/warning fixes

   - various DMI quirk additions"

* tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
  platform/x86/intel: hid: Add DMI switches allow list
  platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
  platform/x86: amd-pmc: Increase the response register timeout
  platform/x86: touchscreen_dmi: Update info for the Chuwi Hi10 Plus (CWI527) tablet
  platform/x86: touchscreen_dmi: Add info for the Chuwi HiBook (CWI514) tablet
  lg-laptop: Correctly handle dmi_get_system_info() returning NULL
  platform/x86/intel: punit_ipc: Drop wrong use of ACPI_PTR()

MAINTAINERS: ARM/VT8500, remove defunct e-mail

linux@prisktech.co.nz is defunct:

4.1.2 <linux@prisktech.co.nz>: Recipient address rejected: Domain not found

Remove it from MAINTAINERS and mark the ARM/VT8500 entry orphan.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

md: fix a lock order reversal in md_alloc

Commit b0140891a8cea3 ("md: Fix race when creating a new md device.")
not only moved assigning mddev->gendisk before calling add_disk, which
fixes the races described in the commit log, but also added a
mddev->open_mutex critical section over add_disk and creation of the
md kobj. Adding a kobject after add_disk is racy vs deleting the gendisk
right after adding it, but md already prevents against that by holding
a mddev->active reference.

On the other hand taking this lock added a lock order reversal with what
is not disk->open_mutex (used to be bdev->bd_mutex when the commit was
added) for partition devices, which need that lock for the internal open
for the partition scan, and a recent commit also takes it for
non-partitioned devices, leading to further lockdep splatter.

Fixes: b0140891a8ce ("md: Fix race when creating a new md device.")
Fixes: d62633873590 ("block: support delayed holder registration")
Reported-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: syzbot+fadc0aaf497e6a493b9f@syzkaller.appspotmail.com
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Song Liu <songliubraving@fb.com>

KVM: selftests: Remove __NR_userfaultfd syscall fallback

Revert the __NR_userfaultfd syscall fallback added for KVM selftests now
that x86's unistd_{32,63}.h overrides are under uapi/ and thus not in
KVM selftests' search path, i.e. now that KVM gets x86 syscall numbers
from the installed kernel headers.

No functional change intended.

Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM: selftests: Add a test for KVM_RUN+rseq to detect task migration bugs

Add a test to verify an rseq's CPU ID is updated correctly if the task is
migrated while the kernel is handling KVM_RUN. This is a regression test
for a bug introduced by commit 72c3c0fe54a3 ("x86/kvm: Use generic xfer
to guest work function"), where TIF_NOTIFY_RESUME would be cleared by KVM
without updating rseq, leading to a stale CPU ID and other badness.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Message-Id: <20210901203030.1292304-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

tools: Move x86 syscall number fallbacks to .../uapi/

Move unistd_{32,64}.h from x86/include/asm to x86/include/uapi/asm so
that tools/selftests that install kernel headers, e.g. KVM selftests, can
include non-uapi tools headers, e.g. to get 'struct list_head', without
effectively overriding the installed non-tool uapi headers.

Swapping KVM's search order, e.g. to search the kernel headers before
tool headers, is not a viable option as doing results in linux/type.h and
other core headers getting pulled from the kernel headers, which do not
have the kernel-internal typedefs that are used through tools, including
many files outside of selftests/kvm's control.

Prior to commit cec07f53c398 ("perf tools: Move syscall number fallbacks
from perf-sys.h to tools/arch/x86/include/asm/"), the handcoded numbers
were actual fallbacks, i.e. overriding unistd_{32,64}.h from the kernel
headers was unintentional.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

entry: rseq: Call rseq_handle_notify_resume() in tracehook_notify_resume()

Invoke rseq_handle_notify_resume() from tracehook_notify_resume() now
that the two function are always called back-to-back by architectures
that have rseq.  The rseq helper is stubbed out for architectures that
don't support rseq, i.e. this is a nop across the board.

Note, tracehook_notify_resume() is horribly named and arguably does not
belong in tracehook.h as literally every line of code in it has nothing
to do with tracing.  But, that's been true since commit a42c6ded827d
("move key_repace_session_keyring() into tracehook_notify_resume()")
first usurped tracehook_notify_resume() back in 2012.  Punt cleaning that
mess up to future patches.

No functional change intended.

Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

KVM: rseq: Update rseq when processing NOTIFY_RESUME on xfer to KVM guest

Invoke rseq's NOTIFY_RESUME handler when processing the flag prior to
transferring to a KVM guest, which is roughly equivalent to an exit to
userspace and processes many of the same pending actions. While the task
cannot be in an rseq critical section as the KVM path is reachable only
by via ioctl(KVM_RUN), the side effects that apply to rseq outside of a
critical section still apply, e.g. the current CPU needs to be updated if
the task is migrated.

Clearing TIF_NOTIFY_RESUME without informing rseq can lead to segfaults
and other badness in userspace VMMs that use rseq in combination with KVM,
e.g. due to the CPU ID being stale after task migration.

Fixes: 72c3c0fe54a3 ("x86/kvm: Use generic xfer to guest work function")
Reported-by: Peter Foley <pefoley@google.com>
Bisected-by: Doug Evans <dje@google.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210901203030.1292304-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

irqchip/gic: Work around broken Renesas integration

Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b44f085 ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().

As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...

Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/CAMuHMdV+Ev47K5NO8XHsanSq5YRMCHn2gWAQyV-q2LpJVy9HiQ@mail.gmail.com

mptcp: ensure tx skbs always have the MPTCP ext

Due to signed/unsigned comparison, the expression:

info->size_goal - skb->len > 0

evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.

Due to the above, syzbot is able to trigger the following WARN_ON():

WARNING: CPU: 1 PID: 810 at net/mptcp/protocol.c:1366 mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Modules linked in:
CPU: 1 PID: 810 Comm: syz-executor.4 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Code: ff 4c 8b 74 24 50 48 8b 5c 24 58 e9 0f fb ff ff e8 13 44 8b f8 4c 89 e7 45 31 ed e8 98 57 2e fe e9 81 f4 ff ff e8 fe 43 8b f8 <0f> 0b 41 bd ea ff ff ff e9 6f f4 ff ff 4c 89 e7 e8 b9 8e d2 f8 e9
RSP: 0018:ffffc9000531f6a0 EFLAGS: 00010216
RAX: 000000000000697f RBX: 0000000000000000 RCX: ffffc90012107000
RDX: 0000000000040000 RSI: ffffffff88eac9e2 RDI: 0000000000000003
RBP: ffff888078b15780 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff88eac017 R11: 0000000000000000 R12: ffff88801de0a280
R13: 0000000000006b58 R14: ffff888066278280 R15: ffff88803c2fe9c0
FS: 00007fd9f866e700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007faebcb2f718 CR3: 00000000267cb000 CR4: 00000000001506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
__mptcp_push_pending+0x1fb/0x6b0 net/mptcp/protocol.c:1547
mptcp_release_cb+0xfe/0x210 net/mptcp/protocol.c:3003
release_sock+0xb4/0x1b0 net/core/sock.c:3206
sk_stream_wait_memory+0x604/0xed0 net/core/stream.c:145
mptcp_sendmsg+0xc39/0x1bc0 net/mptcp/protocol.c:1749
inet6_sendmsg+0x99/0xe0 net/ipv6/af_inet6.c:643
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
sock_write_iter+0x2a0/0x3e0 net/socket.c:1057
call_write_iter include/linux/fs.h:2163 [inline]
new_sync_write+0x40b/0x640 fs/read_write.c:507
vfs_write+0x7cf/0xae0 fs/read_write.c:594
ksys_write+0x1ee/0x250 fs/read_write.c:647
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x4665f9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fd9f866e188 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000056c038 RCX: 00000000004665f9
RDX: 00000000000e7b78 RSI: 0000000020000000 RDI: 0000000000000003
RBP: 00000000004bfcc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000056c038
R13: 0000000000a9fb1f R14: 00007fd9f866e300 R15: 0000000000022000

Fix the issue rewriting the relevant expression to avoid
sign-related problems - note: size_goal is always >= 0.

Additionally, ensure that the skb in the tx cache always carries
the relevant extension.

Reported-and-tested-by: syzbot+263a248eec3e875baa7b@syzkaller.appspotmail.com
Fixes: 1094c6fe7280 ("mptcp: fix possible divide by zero")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: rdma - don't wait for resources under hw error recovery flow

If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.

Fixes: 64515dc899df ("qed: Add infrastructure for error detection and recovery")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

irqchip/renesas-rza1: Use semicolons instead of commas

This code works, but it is cleaner to use semicolons at the end of
statements instead of commas.

Extracted from a big anonymous patch by Julia Lawall
<julia.lawall@inria.fr>.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/b1710bb6ea5faa7a7fe74404adb0beb951e0bf8c.1631699160.git.geert+renesas@glider.be

irqchip/gic-v3-its: Fix potential VPE leak on error

In its_vpe_irq_domain_alloc, when its_vpe_init() returns an error,
there is an off-by-one in the number of VPEs to be freed.

Fix it by simply passing the number of VPEs allocated, which is the
index of the loop iterating over the VPEs.

Fixes: 7d75bbb4bc1a ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Kaige Fu <kaige.fu@linux.alibaba.com>
[maz: fixed commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/d9e36dee512e63670287ed9eff884a5d8d6d27f2.1631672311.git.kaige.fu@linux.alibaba.com

irqchip/goldfish-pic: Select GENERIC_IRQ_CHIP to fix build

irq-goldfish-pic uses GENERIC_IRQ_CHIP interfaces so select that symbol
to fix build errors.

Fixes these build errors:

mips-linux-ld: drivers/irqchip/irq-goldfish-pic.o: in function `goldfish_pic_of_init':
irq-goldfish-pic.c:(.init.text+0xc0): undefined reference to `irq_alloc_generic_chip'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0xf4): undefined reference to `irq_gc_unmask_enable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0xf8): undefined reference to `irq_gc_unmask_enable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x100): undefined reference to `irq_gc_mask_disable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x104): undefined reference to `irq_gc_mask_disable_reg'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x11c): undefined reference to `irq_setup_generic_chip'
mips-linux-ld: irq-goldfish-pic.c:(.init.text+0x168): undefined reference to `irq_remove_generic_chip'

Fixes: 4235ff50cf98 ("irqchip/irq-goldfish-pic: Add Goldfish PIC driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Miodrag Dinic <miodrag.dinic@mips.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Goran Ferenc <goran.ferenc@mips.com>
Cc: Aleksandar Markovic <aleksandar.markovic@mips.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210905162519.21507-1-rdunlap@infradead.org

irqchip/mbigen: Repair non-kernel-doc notation

Fix kernel-doc warnings in irq-mbigen.c:

irq-mbigen.c:29: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* In mbigen vector register
irq-mbigen.c:43: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* offset of clear register in mbigen node
irq-mbigen.c:50: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* offset of interrupt type register

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Jun Ma <majun258@huawei.com>
Cc: Yun Wu <wuyun.wu@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210905033644.15988-1-rdunlap@infradead.org

irqdomain: Change the type of 'size' in __irq_domain_add() to be consistent

The 'size' is used in struct_size(domain, revmap, size) and its input
parameter type is 'size_t'(unsigned int).
Changing the size to 'unsigned int' to make the type consistent.

Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210916025203.44841-1-cuibixuan@huawei.com

irqchip/armada-370-xp: Fix ack/eoi breakage

When converting the driver to using handle_percpu_devid_irq,
we forgot to repaint the irq_eoi() callback into irq_ack(),
as handle_percpu_devid_fasteoi_ipi() was actually using EOI
really early in the handling. Yes this was a stupid idea.

Fix this by using the HW ack method as irq_ack().

Fixes: e52e73b7e9f7 ("irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()")
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87tuiexq5f.fsf@pengutronix.de

ext2: fix sleeping in atomic bugs on error

The ext2_error() function syncs the filesystem so it sleeps.  The caller
is holding a spinlock so it's not allowed to sleep.

   ext2_statfs() <- disables preempt
   -> ext2_count_free_blocks()
      -> ext2_get_group_desc()

Fix this by using WARN() to print an error message and a stack trace
instead of using ext2_error().

Link: https://lore.kernel.org/r/20210921203233.GA16529@kili
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>

gpio/rockchip: fix get_direction value handling

The function uses the newly introduced rockchip_gpio_readl_bit()
which directly returns the actual value of the requeste bit.
So using the existing bit-wise check for the bit inside the value
will always return 0.

Fix this by dropping the bit manipulation on the result.

Fixes: 3bcbd1a85b68 ("gpio/rockchip: support next version gpio controller")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

gpio/rockchip: extended debounce support is only available on v2

The gpio driver runs into issues on v1 gpio blocks, as the db_clk
and the whole extended debounce support is only ever defined on v2.
So checking for the IS_ERR on the db_clk is not enough, as it will
be NULL on v1.

Fix this by adding the needed condition for v2 first before checking
the existence of the db_clk.

This caused my rk3288-veyron-pinky to enter a reboot loop when it
tried to enable the power-key as adc-key device.

Fixes: 3bcbd1a85b68 ("gpio/rockchip: support next version gpio controller")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

gpio: gpio-aspeed-sgpio: Fix wrong hwirq in irq handler.

The current hwirq is calculated based on the old GPIO pin order(input
GPIO range is from 0 to ngpios - 1).
It should be calculated based on the current GPIO input pin order(input
GPIOs are 0, 2, 4, ..., (ngpios - 1) * 2).

Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

gpio: uniphier: Fix void functions to remove return value

The return type of irq_chip.irq_mask() and irq_chip.irq_unmask() should
be void.

Fixes: dbe776c2ca54 ("gpio: uniphier: add UniPhier GPIO controller driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

gpiolib: acpi: Make set-debounce-timeout failures non fatal

Commit 8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings")
made the gpiolib-acpi code call gpio_set_debounce_timeout() when requesting
GPIOs.

This in itself is fine, but it also made gpio_set_debounce_timeout()
errors fatal, causing the requesting of the GPIO to fail. This is causing
regressions. E.g. on a HP ElitePad 1000 G2 various _AEI specified GPIO
ACPI event sources specify a debouncy timeout of 20 ms, but the
pinctrl-baytrail.c only supports certain fixed values, the closest
ones being 12 or 24 ms and pinctrl-baytrail.c responds with -EINVAL
when specified a value which is not one of the fixed values.

This is causing the acpi_request_own_gpiod() call to fail for 3
ACPI event sources on the HP ElitePad 1000 G2, which in turn is causing
e.g. the battery charging vs discharging status to never get updated,
even though a charger has been plugged-in or unplugged.

Make gpio_set_debounce_timeout() errors non fatal, warning about the
failure instead, to fix this regression.

Note we should probably also fix various pinctrl drivers to just
pick the first bigger discrete value rather then returning -EINVAL but
this will need to be done on a per driver basis, where as this fix
at least gets us back to where things were before and thus restores
functionality on devices where this was lost due to
gpio_set_debounce_timeout() errors.

Fixes: 8dcb7a15a585 ("gpiolib: acpi: Take into account debounce settings")
Depends-on: 2e2b496cebef ("gpiolib: acpi: Extract acpi_request_own_gpiod() helper")
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

MAINTAINERS: usb, update Peter Korsgaard's entries

Peter's e-mail in MAINTAINERS is defunct:
This is the qmail-send program at a.mx.sunsite.dk.
<jacmet@sunsite.dk>:
Sorry, no mailbox here by that name. (#5.1.1)

Peter says:
** Ahh yes, it should be changed to peter@korsgaard.com.

However he also says:
** I haven't had access to c67x00 hw for quite some years though, so maybe
** it should be marked Orphan instead?

So change as he wishes.

Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210922063008.25758-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ses: Retry failed Send/Receive Diagnostic commands

Setting SCSI logging level with error=3, we saw some errors from enclosues:

[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13

Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).

Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com
Reviewed-by: Brian King <brking@linux.ibm.com>
Reviewed-by: James Bottomley <jejb@linux.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: target: Fix spelling mistake "CONFLIFT" -> "CONFLICT"

There is a spelling mistake in a dev_err message. Fix it.

Link: https://lore.kernel.org/r/20210920183206.17477-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix gcc -Wstringop-overread warning, again

I fixed a stringop-overread warning earlier this year, now a second copy of
the original code was added and the warning came back:

drivers/scsi/lpfc/lpfc_attr.c: In function 'lpfc_cmf_info_show':
drivers/scsi/lpfc/lpfc_attr.c:289:25: error: 'strnlen' specified bound 4095 exceeds source size 24 [-Werror=stringop-overread]
289 | strnlen(LPFC_INFO_MORE_STR, PAGE_SIZE - 1),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Fix it the same way as the other copy.

Link: https://lore.kernel.org/r/20210920095628.1191676-1-arnd@kernel.org
Fixes: ada48ba70f6b ("scsi: lpfc: Fix gcc -Wstringop-overread warning")
Fixes: 74a7baa2a3ee ("scsi: lpfc: Add cmf_info sysfs entry")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Use correct scnprintf() limit

The limit should be "PAGE_SIZE - len" instead of "PAGE_SIZE". We're not
going to hit the limit so this fix will not affect runtime.

Link: https://lore.kernel.org/r/20210916132331.GE25094@kili
Fixes: 5b9e70b22cc5 ("scsi: lpfc: raise sg count for nvme to use available sg resources")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: lpfc: Fix sprintf() overflow in lpfc_display_fpin_wwpn()

This scnprintf() uses the wrong limit. It should be
"LPFC_FPIN_WWPN_LINE_SZ - len" instead of LPFC_FPIN_WWPN_LINE_SZ.

Link: https://lore.kernel.org/r/20210916132251.GD25094@kili
Fixes: 428569e66fa7 ("scsi: lpfc: Expand FPIN and RDF receive logging")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: core: Remove 'current_tag'

The 'current_tag' field in struct scsi_device is unused now; remove it.

Link: https://lore.kernel.org/r/1631696835-136198-4-git-send-email-john.garry@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: acornscsi: Remove tagged queuing vestiges

The acornscsi driver has a config option to enable tagged queuing, but this
option gets disabled in the driver itself with the comment 'needs to be
debugged'. As this is a _really_ old driver I doubt anyone will be wanting
to invest time here, so remove the tagged queue vestiges and make our lives
easier.

[jpg: Use scsi_cmd_to_rq()]

Link: https://lore.kernel.org/r/1631696835-136198-3-git-send-email-john.garry@huawei.com
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: fas216: Kill scmd->tag

The driver is attempting to allocate a tag internally which is a no-go with
blk-mq. Switch the driver to use the request tag and kill usage of
scmd->tag and scmd->device->current_tag.

[jpg: Change to use scsi_cmd_to_rq()]

Link: https://lore.kernel.org/r/1631696835-136198-2-git-send-email-john.garry@huawei.com
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: qla2xxx: Restore initiator in dual mode

In dual mode in case of disabling the target, the whole port goes offline
and initiator is turned off too.

Fix restoring initiator mode after disabling target in dual mode.

Link: https://lore.kernel.org/r/20210915153239.8035-1-d.bogdanov@yadro.com
Fixes: 0645cb8350cd ("scsi: qla2xxx: Add mode control for each physical port")
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: core: Unbreak the reset handler

A command tag is passed as the second argument of the
__ufshcd_transfer_req_compl() call in ufshcd_eh_device_reset_handler()
instead of a bitmask. Fix this by passing a bitmask as argument instead of
a command tag.

Link: https://lore.kernel.org/r/20210916175408.2260084-1-bvanassche@acm.org
Fixes: a45f937110fa ("scsi: ufs: Optimize host lock on transfer requests send/compl paths")
Cc: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: sd_zbc: Support disks with more than 2**32 logical blocks

This patch addresses the following Coverity report about the zno *
sdkp->zone_blocks expression:

CID 1475514 (#1 of 1): Unintentional integer overflow (OVERFLOW_BEFORE_WIDEN)
overflow_before_widen: Potentially overflowing expression zno *
sdkp->zone_blocks with type unsigned int (32 bits, unsigned) is evaluated
using 32-bit arithmetic, and then used in a context that expects an
expression of type sector_t (64 bits, unsigned).

Link: https://lore.kernel.org/r/20210917212314.2362324-1-bvanassche@acm.org
Fixes: 5795eb443060 ("scsi: sd_zbc: emulate ZONE_APPEND commands")
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Damien Le Moal <Damien.LeMoal@wdc.com>
Cc: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

scsi: ufs: core: Revert "scsi: ufs: Synchronize SCSI and UFS error handling"

This reverts commit a113eaaf86373362b053279049907ff82b5df6c8.

There are a couple of issues with the commit:

1. It causes deadlocks.

2. It causes the shost->eh_cmd_q list of failed requests not to be
    processed, ever.

So revert it.

1. Deadlocks

The SCSI error handler runs with requests blocked beginning when
scsi_schedule_eh() sets SHOST_RECOVERY state, continuing through
scsi_error_handler() callback ->eh_strategy_handler() until
scsi_restart_operations() is called.  By setting eh_strategy_handler to
ufshcd_err_handler, the patch changed the UFS error handler to run with
requests blocked, including PM requests, for the entire run of the error
handler.

That conflicts with UFS error handler existing synchronization with UFS
device PM operations.  The UFS error handler synchronizes with runtime PM
by doing pm_runtime_get_sync() prior to blocking requests itself.  It
synchronizes with system PM by use of hba->host_sem, again before blocking
requests itself.  However, if requests are already blocked, then PM
operations will block.  So:

   the UFS error handler blocks waiting on PM
+ PM blocks waiting on SCSI PM requests to process or fail
+ PM requests are blocked waiting on error handling to finish
=  deadlock

This happens both for runtime PM and system PM.

Prior to the patch, these deadlocks could not happen even if SCSI error
handling was running, because the presence of requests in shost->eh_cmd_q
would mean the queues could not be suspended, which would mean that, should
the UFS error handler run at the same time, it would not need to wait for
PM or vice versa.

Please note these scenarios are not just theoretical, they were found
during testing on a Samsung Galaxy Book S.

2. ->eh_strategy_handler() must process shost->eh_cmd_q list of failed
requests, as all other eh_strategy_handler's do except UFS error handler.
Refer for example: scsi_unjam_host(), ata_scsi_error() and
sas_scsi_recover_host().

Link: https://lore.kernel.org/r/20210917144349.14058-1-adrian.hunter@intel.com
Fixes: a113eaaf8637 ("scsi: ufs: Synchronize SCSI and UFS error handling")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Merge branch 's390-qeth-fixes-2021-09-21'

Julian Wiedmann says:

====================
s390/qeth: fixes 2021-09-21

This brings two fixes for deadlocks when a device is removed while it
has certain types of async work pending. And one additional fix for a
missing NULL check in an error case.
====================

Link: https://lore.kernel.org/r/20210921145217.1584654-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

s390/qeth: fix deadlock during failing recovery

Commit 0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery") removed
taking discipline_mutex inside qeth_do_reset(), fixing potential
deadlocks. An error path was missed though, that still takes
discipline_mutex and thus has the original deadlock potential.

Intermittent deadlocks were seen when a qeth channel path is configured
offline, causing a race between qeth_do_reset and ccwgroup_remove.
Call qeth_set_offline() directly in the qeth_do_reset() error case and
then a new variant of ccwgroup_set_offline(), without taking
discipline_mutex.

Fixes: b41b554c1ee7 ("s390/qeth: fix locking for discipline setup / removal")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

s390/qeth: Fix deadlock in remove_discipline

Problem: qeth_close_dev_handler is a worker that tries to acquire
card->discipline_mutex via drv->set_offline() in ccwgroup_set_offline().
Since commit b41b554c1ee7
("s390/qeth: fix locking for discipline setup / removal")
qeth_remove_discipline() is called under card->discipline_mutex and
cancels the work and waits for it to finish.

STOPLAN reception with reason code IPA_RC_VEPA_TO_VEB_TRANSITION is the
only situation that schedules close_dev_work. In that situation scheduling
qeth recovery will also result in an offline interface, when resetting the
isolation mode fails, if the external switch is still set to VEB.
And since commit 0b9902c1fcc5 ("s390/qeth: fix deadlock during recovery")
qeth recovery does not aquire card->discipline_mutex anymore.

So we accept the longer pathlength of qeth_schedule_recovery in this
error situation and re-use the existing function.

As a side-benefit this changes the hwtrap to behave like during recovery
instead of like during a user-triggered set_offline.

Fixes: b41b554c1ee7 ("s390/qeth: fix locking for discipline setup / removal")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

s390/qeth: fix NULL deref in qeth_clear_working_pool_list()

When qeth_set_online() calls qeth_clear_working_pool_list() to roll
back after an error exit from qeth_hardsetup_card(), we are at risk of
accessing card->qdio.in_q before it was allocated by
qeth_alloc_qdio_queues() via qeth_mpc_initialize().

qeth_clear_working_pool_list() then dereferences NULL, and by writing to
queue->bufs[i].pool_entry scribbles all over the CPU's lowcore.
Resulting in a crash when those lowcore areas are used next (eg. on
the next machine-check interrupt).

Such a scenario would typically happen when the device is first set
online and its queues aren't allocated yet. An early IO error or certain
misconfigs (eg. mismatched transport mode, bad portno) then cause us to
error out from qeth_hardsetup_card() with card->qdio.in_q still being
NULL.

Fix it by checking the pointer for NULL before accessing it.

Note that we also have (rare) paths inside qeth_mpc_initialize() where
a configuration change can cause us to free the existing queues,
expecting that subsequent code will allocate them again. If we then
error out before that re-allocation happens, the same bug occurs.

Fixes: eff73e16ee11 ("s390/qeth: tolerate pre-filled RX buffer")
Reported-by: Stefan Raspl <raspl@linux.ibm.com>
Root-caused-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

cifs: fix a sign extension bug

The problem is the mismatched types between "ctx->total_len" which is
an unsigned int, "rc" which is an int, and "ctx->rc" which is a
ssize_t. The code does:

ctx->rc = (rc == 0) ? ctx->total_len : rc;

We want "ctx->rc" to store the negative "rc" error code. But what
happens is that "rc" is type promoted to a high unsigned int and
'ctx->rc" will store the high positive value instead of a negative
value.

The fix is to change "rc" from an int to a ssize_t.

Fixes: c610c4b619e5 ("CIFS: Add asynchronous write support through kernel AIO")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

spi: Revert modalias changes

During the v5.13 cycle we updated the SPI subsystem to generate OF style
modaliases for SPI devices, replacing the old Linux style modalises we
used to generate based on spi_device_id which are the DT style name with
the vendor removed.  Unfortunately this means that we start only
reporting OF style modalises and not the old ones and there is nothing
that ensures that drivers list every possible OF compatible string in
their OF ID table.  The result is that there are systems which have been
relying on loading modules based on the old style that are now broken,
as found by Russell King with spi-nor on Macchiatobin.

spi-nor is a particularly problematic case for this, it only lists a
single generic DT compatible jedec,spi-nor in the driver but supports a
huge raft of device specific compatibles, with a large set of part
numbers many of which are offered by multiple vendors.  Russell's
searches of upstream device trees has turned up examples with vendor
names written in non-standard ways too.  To make matters worse up until
8ff16cf77ce3 ("Documentation: devicetree: m25p80: add "nor-jedec"
binding") the generic compatible was not part of the binding so there
are device trees out there written to that binding version which don't
list it all.  The sheer number of parts supported together with our
previous approach of ignoring the vendor ID makes robustly fixing this
by adding compatibles to the spi-nor driver seem problematic, the
current DT binding document does not list all the parts supported by the
driver at the minute (further patches will fix this).

I've also investigated supporting both formats of modalias
simultaneously but that doesn't seem possible, especially without
breaking our userspace ABI which is obviously not viable.

Instead revert the relevant changes for now:

e09f2ab8eecc ("spi: update modalias_show after of_device_uevent_modalias support")
3ce6c9e2617e ("spi: add of_device_uevent_modalias support")

This will unfortunately mean that any system which had started having
modules autoload based on the OF compatibles for drivers that list
things there but not in the spi_device_ids will now not have those
modules load which is itself a regression.  Since it affects a narrower
time window and the particularly problematic spi-nor driver may be
critical to system boot on smaller systems this seems the best of a
series of bad options.  I will start an audit of SPI drivers to identify
and fix cases where things won't autoload using spi_device_id, this is
not great but seems to be the best way forward that anyone has been able
to identify.

Thanks to Russell for both his report and the additional diagnostic and
analysis work he has done here, the detailed research above was his
work.

Fixes: e09f2ab8eecc ("spi: update modalias_show after of_device_uevent_modalias support")
Fixes: 3ce6c9e2617e ("spi: add of_device_uevent_modalias support")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Andreas Schwab <schwab@suse.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>

ksmbd: add default data stream name in FILE_STREAM_INFORMATION

Windows client expect to get default stream name(::DATA) in
FILE_STREAM_INFORMATION response even if there is no stream data in file.
This patch fix update failure when writing ppt or doc files.

Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Reviewed-By: Tom Talpey <tom@talpey.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

ksmbd: log that server is experimental at module load

While we are working through detailed security reviews
of ksmbd server code we should remind users that it is an
experimental module by adding a warning when the module
loads. Currently the module shows as experimental
in Kconfig and is disabled by default, but we don't want
to confuse users.

Although ksmbd passes a wide variety of the
important functional tests (since initial focus had
been largely on functional testing such as smbtorture,
xfstests etc.), and ksmbd has added key security
features (e.g. GCM256 encryption, Kerberos support),
there are ongoing detailed reviews of the code base
for path processing and network buffer decoding, and
this patch reminds users that the module should be
considered "experimental."

Reviewed-by: Namjae Jeon <linkinjeon@kernel.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

kselftest/arm64: signal: Skip tests if required features are missing

During initialization of a signal testcase, features declared as required
are properly checked against the running system but no action is then taken
to effectively skip such a testcase.

Fix core signals test logic to abort initialization and report such a
testcase as skipped to the KSelfTest framework.

Fixes: f96bf4340316 ("kselftest: arm64: mangle_pstate_invalid_compat_toggle and common utils")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210920121228.35368-1-cristian.marussi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Merge tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux

Pull s390 eBPF fixes from Vasily Gorbik:
"Johan Almbladh has implemented a number of new testcases for eBPF [1],
  which uncovered three miscompilation issues in the s390 eBPF JIT"

Link: https://lore.kernel.org/bpf/20210902185229.1840281-1-johan.almbladh@anyfinetworks.com/
* tag 's390-5.15-ebpf-jit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/bpf: Fix optimizing out zero-extensions
  s390/bpf: Fix 64-bit subtraction of the -0x80000000 constant
  s390/bpf: Fix branch shortening during codegen pass

comedi: Fix memory leak in compat_insnlist()

`compat_insnlist()` handles the 32-bit version of the `COMEDI_INSNLIST`
ioctl (whenwhen `CONFIG_COMPAT` is enabled). It allocates memory to
temporarily hold an array of `struct comedi_insn` converted from the
32-bit version in user space. This memory is only being freed if there
is a fault while filling the array, otherwise it is leaked.

Add a call to `kfree()` to fix the leak.

Fixes: b8d47d881305 ("comedi: get rid of compat_alloc_user_space() mess in COMEDI_INSNLIST compat")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev
Cc: <stable@vger.kernel.org> # 5.13+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20210916145023.157479-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: fix off by one bugs in unsafe_request_wait()

The "> max" tests should be ">= max" to prevent an out of bounds access
on the next lines.

Fixes: e1a4541ec0b9 ("ceph: flush the mdlog before waiting on unsafe reqs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>

nvmem: NVMEM_NINTENDO_OTP should depend on WII

The Nintendo Wii and Wii U OTP is only present on Nintendo Wii and Wii U
consoles. Hence add a dependency on WII, to prevent asking the user
about this driver when configuring a kernel without Nintendo Wii and Wii
U console support.

Fixes: 3683b761fe3a10ad ("nvmem: nintendo-otp: Add new driver for the Wii and Wii U OTP")
Reviewed-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/01318920709dddc4d85fe895e2083ca0eee234d8.1631611652.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qnx4: work around gcc false positive warning bug

In commit b7213ffa0e58 ("qnx4: avoid stringop-overread errors") I tried
to teach gcc about how the directory entry structure can be two
different things depending on a status flag.  It made the code clearer,
and it seemed to make gcc happy.

However, Arnd points to a gcc bug, where despite using two different
members of a union, gcc then gets confused, and uses the size of one of
the members to decide if a string overrun happens.  And not necessarily
the rigth one.

End result: with some configurations, gcc-11 will still complain about
the source buffer size being overread:

  fs/qnx4/dir.c: In function 'qnx4_readdir':
  fs/qnx4/dir.c:76:32: error: 'strnlen' specified bound [16, 48] exceeds source size 1 [-Werror=stringop-overread]
     76 |                         size = strnlen(name, size);
        |                                ^~~~~~~~~~~~~~~~~~~
  fs/qnx4/dir.c:26:22: note: source object declared here
     26 |                 char de_name;
        |                      ^~~~~~~

because gcc will get confused about which union member entry is actually
getting accessed, even when the source code is very clear about it.  Gcc
internally will have combined two "redundant" pointers (pointing to
different union elements that are at the same offset), and takes the
size checking from one or the other - not necessarily the right one.

This is clearly a gcc bug, but we can work around it fairly easily.  The
biggest thing here is the big honking comment about why we do what we
do.

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99578#c6
Reported-and-tested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

usb: musb: tusb6010: uninitialized data in tusb_fifo_write_unaligned()

This is writing to the first 1 - 3 bytes of "val" and then writing all
four bytes to musb_writel(). The last byte is always going to be
garbage. Zero out the last bytes instead.

Fixes: 550a7375fe72 ("USB: Add MUSB and TUSB support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210916135737.GI25094@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-storage: Add quirk for ScanLogic SL11R-IDE older than 2.6c

ScanLogic SL11R-IDE with firmware older than 2.6c (the latest one) has
broken tag handling, preventing the device from working at all:
usb 1-1: new full-speed USB device number 2 using uhci_hcd
usb 1-1: New USB device found, idVendor=04ce, idProduct=0002, bcdDevice= 2.60
usb 1-1: New USB device strings: Mfr=1, Product=1, SerialNumber=0
usb 1-1: Product: USB Device
usb 1-1: Manufacturer: USB Device
usb-storage 1-1:1.0: USB Mass Storage device detected
scsi host2: usb-storage 1-1:1.0
usbcore: registered new interface driver usb-storage
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd
usb 1-1: reset full-speed USB device number 2 using uhci_hcd

Add US_FL_BULK_IGNORE_TAG to fix it. Also update my e-mail address.

2.6c is the only firmware that claims Linux compatibility.
The firmware can be upgraded using ezotgdbg utility:
https://github.com/asciilifeform/ezotgdbg

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210913210106.12717-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Re-enable UAS for LaCie Rugged USB3-FW with fk quirk

Further testing has revealed that LaCie Rugged USB3-FW does work with
uas as long as US_FL_NO_REPORT_OPCODES and US_FL_NO_SAME are enabled.

Link: https://lore.kernel.org/linux-usb/2167ea48-e273-a336-a4e0-10a4e883e75e@redhat.com/
Cc: stable <stable@vger.kernel.org>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Julian Sikorski <belegdol+github@gmail.com>
Link: https://lore.kernel.org/r/20210913181454.7365-1-belegdol+github@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

misc: bcm-vk: fix tty registration race

Make sure to set the tty class-device driver data before registering the
tty to avoid having a racing open() dereference a NULL pointer.

Fixes: 91ca10d6fa07 ("misc: bcm-vk: add ttyVK support")
Cc: stable@vger.kernel.org # 5.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210917115736.5816-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Mitigate MTE issues with str{n}cmp()

As with strlen(), the patches importing the updated str{n}cmp()
implementations were originally developed and tested before the
advent of CONFIG_KASAN_HW_TAGS, and have subsequently revealed
not to be MTE-safe. Since in-kernel MTE is still a rather niche
case, let it temporarily fall back to the generic C versions for
correctness until we can figure out the best fix.

Fixes: 758602c04409 ("arm64: Import latest version of Cortex Strings' strcmp")
Fixes: 020b199bc70d ("arm64: Import latest version of Cortex Strings' strncmp")
Cc: <stable@vger.kernel.org> # 5.14.x
Reported-by: Branislav Rankov <branislav.rankov@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/34dc4d12eec0adae49b0ac927df642ed10089d40.1631890770.git.robin.murphy@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX

Tested with a AMD Ryzen 7 5800X.

Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Thomas Weißschuh <thomas@weissschuh.net>
Link: https://lore.kernel.org/r/20210921100702.3838-1-tjakobi@math.uni-bielefeld.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86/intel: hid: Add DMI switches allow list

Some devices, even non convertible ones, can send incorrect
SW_TABLET_MODE reports.

Add an allow list and accept such reports only from devices in it.

Bug reported for Dell XPS 17 9710 on:
https://gitlab.freedesktop.org/libinput/libinput/-/issues/662

Reported-by: Tobias Gurtzick <magic@wizardtales.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Tobias Gurtzick <magic@wizardtales.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20210920160312.9787-1-jose.exposito89@gmail.com
[hdegoede@redhat.com: Check dmi_switches_auto_add_allow_list only once]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error

When DELL_WMI=y, DELL_WMI_PRIVACY=y, and LEDS_TRIGGER_AUDIO=m, there
is a linker error since the LEDS trigger code is built as a loadable
module. This happens because DELL_WMI_PRIVACY is a bool that depends
on a tristate (LEDS_TRIGGER_AUDIO=m), which can be dangerous.

ld: drivers/platform/x86/dell/dell-wmi-privacy.o: in function `dell_privacy_wmi_probe':
dell-wmi-privacy.c:(.text+0x3df): undefined reference to `ledtrig_audio_get'

Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Perry Yuan <Perry.Yuan@dell.com>
Cc: Dell.Client.Kernel@dell.com
Cc: platform-driver-x86@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <mgross@linux.intel.com>
Link: https://lore.kernel.org/r/20210918044829.19222-1-rdunlap@infradead.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

thermal/drivers/tsens: Fix wrong check for tzd in irq handlers

Some devices can have some thermal sensors disabled from the
factory. The current two irq handler functions check all the sensor by
default and the check if the sensor was actually registered is
wrong. The tzd is actually never set if the registration fails hence
the IS_ERR check is wrong.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210907212543.20220-1-ansuelsmth@gmail.com

thermal/core: Potential buffer overflow in thermal_build_list_of_policies()

After printing the list of thermal governors, then this function prints
a newline character. The problem is that "size" has not been updated
after printing the last governor. This means that it can write one
character (the NUL terminator) beyond the end of the buffer.

Get rid of the "size" variable and just use "PAGE_SIZE - count" directly.

Fixes: 1b4f48494eb2 ("thermal: core: group functions related to governor handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210916131342.GB25094@kili

Merge branch 'dsa-devres'

Vladimir Oltean says:

====================
Fix mdiobus users with devres

Commit ac3a68d56651 ("net: phy: don't abuse devres in
devm_mdiobus_register()") by Bartosz Golaszewski has introduced two
classes of potential bugs by making the devres callback of
devm_mdiobus_alloc stop calling mdiobus_unregister.

The exact buggy circumstances are presented in the individual commit
messages. I have searched the tree for other occurrences, but at the
moment:

- for issue (a) I have no concrete proof that other buses except SPI and
  I2C suffer from it, and the only SPI or I2C device drivers that call
  of_mdiobus_alloc are the DSA drivers that leave a NULL
  ds->slave_mii_bus and a non-NULL ds->ops->phy_read, aka ksz9477,
  ksz8795, lan9303_i2c, vsc73xx-spi.

- for issue (b), all drivers which call of_mdiobus_alloc either use
  of_mdiobus_register too, or call mdiobus_unregister sometime within
  the ->remove path.

Although at this point I've seen enough strangeness caused by this
"device_del during ->shutdown" that I'm just going to copy the SPI and
I2C subsystem maintainers to this patch series, to get their feedback
whether they've had reports about things like this before. I don't think
other buses behave in this way, it forces SPI and I2C devices to have to
protect themselves from a really strange set of issues.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: realtek: register the MDIO bus under devres

The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:

spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
   -> spi_unregister_device(to_spi_device(dev));
      -> device_del(&spi->dev);

So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:

i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
   -> i2c_unregister_device(client);
      -> device_unregister(&client->dev);

The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).

So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.

This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:

void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}

BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;

put_device(&bus->dev);
}

In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.

I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:

(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
    located on a bus that unregisters its children on shutdown. After
    the blamed patch, either both the alloc and the register should use
    devres, or none should.

(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
    mdiobus_unregister at all in the remove path. After the blamed
    patch, nobody unregisters the MDIO bus anymore, so this is even more
    buggy than the previous case which needs a specific bus
    configuration to be seen, this one is an unconditional bug.

In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.

Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: don't allocate the slave_mii_bus using devres

The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:

spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
   -> spi_unregister_device(to_spi_device(dev));
      -> device_del(&spi->dev);

So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:

i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
   -> i2c_unregister_device(client);
      -> device_unregister(&client->dev);

The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).

So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.

This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:

void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}

BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;

put_device(&bus->dev);
}

In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.

I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:

(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
    located on a bus that unregisters its children on shutdown. After
    the blamed patch, either both the alloc and the register should use
    devres, or none should.

(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
    mdiobus_unregister at all in the remove path. After the blamed
    patch, nobody unregisters the MDIO bus anymore, so this is even more
    buggy than the previous case which needs a specific bus
    configuration to be seen, this one is an unconditional bug.

In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.

It does this on probe:

if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus

and this on remove:

if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus

I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.

So in that case, if unregistering is fine, freeing must be fine too.

Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.

Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

arm64: add MTE supported check to thread switching and syscall entry/exit

This lets us avoid doing unnecessary work on hardware that does not
support MTE, and will allow us to freely use MTE instructions in the
code called by mte_thread_switch().

Since this would mean that we do a redundant check in
mte_check_tfsr_el1(), remove it and add two checks now required in its
callers. This also avoids an unnecessary DSB+ISB sequence on the syscall
exit path for hardware not supporting MTE.

Fixes: 65812c6921cc ("arm64: mte: Enable async tag check fault")
Cc: <stable@vger.kernel.org> # 5.13.x
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/I02fd000d1ef2c86c7d2952a7f099b254ec227a5d
Link: https://lore.kernel.org/r/20210915190336.398390-1-pcc@google.com
[catalin.marinas@arm.com: adjust the commit log slightly]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

drm/i915: Free all DMC payloads

Free all the DMC payloads, not just DMC_MAIN.

unreferenced object 0xffff88ff32d4d800 (size 1024):
  comm "kworker/1:5", pid 701, jiffies 4294904239 (age 109.736s)
  hex dump (first 32 bytes):
    40 40 00 0c 03 00 00 00 00 00 00 00 00 00 00 00  @@..............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000ba9d0d95>] dmc_load_work_fn+0x34d/0x510 [i915]
    [<000000001049fcab>] process_one_work+0x261/0x550
    [<00000000eeb995ac>] worker_thread+0x49/0x3c0
    [<0000000021031dc3>] kthread+0x10b/0x140
    [<000000004a0f69ee>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff88ff0bde4000 (size 1024):
  comm "kworker/0:3", pid 708, jiffies 4294904469 (age 108.816s)
  hex dump (first 32 bytes):
    40 40 00 0c 01 00 00 00 00 00 00 00 00 00 00 00  @@..............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<00000000ba9d0d95>] dmc_load_work_fn+0x34d/0x510 [i915]
    [<000000001049fcab>] process_one_work+0x261/0x550
    [<00000000eeb995ac>] worker_thread+0x49/0x3c0
    [<0000000021031dc3>] kthread+0x10b/0x140
    [<000000004a0f69ee>] ret_from_fork+0x1f/0x30

Fixes: 3d5928a168a9 ("drm/i915/xelpd: Pipe A DMC plugging")
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210809194805.3793060-1-lucas.demarchi@intel.com
(cherry picked from commit 064b877dff4252ced91a1c8b1f129073f2991f6e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Move __i915_gem_free_object to ttm_bo_destroy

When we implement delayed destroy, we may have a second
call to the delete_mem_notify() handler, while free_object()
only should be called once.

Move it to bo->destroy(), to ensure it's only called once.
This fixes some weird memory corruption issues with delayed
destroy when async eviction is used.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210830121006.2978297-2-maarten.lankhorst@linux.intel.com
Fixes: 213d50927763 ("drm/i915/ttm: Introduce a TTM i915 gem object backend")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
(cherry picked from commit 48b0961269546716c3232748bf37e64e49fb866c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Update memory bandwidth parameters

Earlier while calculating derated bw we would use 90% of the calculated
bw. Starting ADL-P we use a non standard derating. Updating the formulae
to reflect the same.

Bspec: 64631

v2: Use the new derating value only for ADL-P(MattR)

Fixes: 4d32fe2f14a7 ("drm/i915/adl_p: Update memory bandwidth parameters")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914220744.16042-1-radhakrishna.sripada@intel.com
(cherry picked from commit f6d66fc8cf5f673ea76407be84dc17dbb3eda108)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Doc: networking: Fox a typo in ice.rst

This patch fixes a spelling typo in ice.rst

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: fix dsa_tree_setup error path

Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.

However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.

Fixes: a57d8c217aad ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'smc-fixes'

Karsten Graul says:

====================
net/smc: fixes 2021-09-20

Please apply the following patches for smc to netdev's net tree.

The first patch adds a missing error check, and the second patch
fixes a possible leak of a lock in a worker.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work

The abort_work is scheduled when a connection was detected to be
out-of-sync after a link failure. The work calls smc_conn_kill(),
which calls smc_close_active_abort() and that might end up calling
smc_close_cancel_work().
smc_close_cancel_work() cancels any pending close_work and tx_work but
needs to release the sock_lock before and acquires the sock_lock again
afterwards. So when the sock_lock was NOT acquired before then it may
be held after the abort_work completes. Thats why the sock_lock is
acquired before the call to smc_conn_kill() in __smc_lgr_terminate(),
but this is missing in smc_conn_abort_work().

Fix that by acquiring the sock_lock first and release it after the
call to smc_conn_kill().

Fixes: b286a0651e44 ("net/smc: handle incoming CDC validation message")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc: add missing error check in smc_clc_prfx_set()

Coverity stumbled over a missing error check in smc_clc_prfx_set():

*** CID 1475954:  Error handling issues  (CHECKED_RETURN)
/net/smc/smc_clc.c: 233 in smc_clc_prfx_set()
>>>     CID 1475954:  Error handling issues  (CHECKED_RETURN)
>>>     Calling "kernel_getsockname" without checking return value (as is done elsewhere 8 out of 10 times).
233      kernel_getsockname(clcsock, (struct sockaddr *)&addrs);

Add the return code check in smc_clc_prfx_set().

Fixes: c246d942eabc ("net/smc: restructure netinfo for CLC proposal msgs")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

x86/setup: Call early_reserve_memory() earlier

Commit in Fixes introduced early_reserve_memory() to do all needed
initial memblock_reserve() calls in one function. Unfortunately, the call
of early_reserve_memory() is done too late for Xen dom0, as in some
cases a Xen hook called by e820__memory_setup() will need those memory
reservations to have happened already.

Move the call of early_reserve_memory() before the call of
e820__memory_setup() in order to avoid such problems.

Fixes: a799c2bd29d1 ("x86/setup: Consolidate early memory reservations")
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20210920120421.29276-1-jgross@suse.com

xen/x86: fix PV trap handling on secondary processors

The initial observation was that in PV mode under Xen 32-bit user space
didn't work anymore. Attempts of system calls ended in #GP(0x402). All
of the sudden the vector 0x80 handler was not in place anymore. As it
turns out up to 5.13 redundant initialization did occur: Once from
cpu_initialize_context() (through its VCPUOP_initialise hypercall) and a
2nd time while each CPU was brought fully up. This 2nd initialization is
now gone, uncovering that the 1st one was flawed: Unlike for the
set_trap_table hypercall, a full virtual IDT needs to be specified here;
the "vector" fields of the individual entries are of no interest. With
many (kernel) IDT entries still(?) (i.e. at that point at least) empty,
the syscall vector 0x80 ended up in slot 0x20 of the virtual IDT, thus
becoming the domain's handler for vector 0x20.

Make xen_convert_trap_info() fit for either purpose, leveraging the fact
that on the xen_copy_trap_info() path the table starts out zero-filled.
This includes moving out the writing of the sentinel, which would also
have lead to a buffer overrun in the xen_copy_trap_info() case if all
(kernel) IDT entries were populated. Convert the writing of the sentinel
to clearing of the entire table entry rather than just the address
field.

(I didn't bother trying to identify the commit which uncovered the issue
in 5.14; the commit named below is the one which actually introduced the
bad code.)

Fixes: f87e4cac4f4e ("xen: SMP guest support")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/7a266932-092e-b68f-f2bb-1473b61adc6e@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

xen/balloon: fix balloon kthread freezing

Commit 8480ed9c2bbd56 ("xen/balloon: use a kernel thread instead a
workqueue") switched the Xen balloon driver to use a kernel thread.
Unfortunately the patch omitted to call try_to_freeze() or to use
wait_event_freezable_timeout(), causing a system suspend to fail.

Fixes: 8480ed9c2bbd56 ("xen/balloon: use a kernel thread instead a workqueue")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210920100345.21939-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>

nvme: keep ctrl->namespaces ordered

Various places in the nvme code that rely on ctrl->namespace to be
ordered. Ensure that the namespae is inserted into the list at the
right position from the start instead of sorting it after the fact.

Fixes: 540c801c65eb ("NVMe: Implement namespace list scanning")
Reported-by: Anton Eidelman <anton.eidelman@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>

nvme-tcp: fix incorrect h2cdata pdu offset accounting

When the controller sends us multiple r2t PDUs in a single
request we need to account for it correctly as our send/recv
context run concurrently (i.e. we get a new r2t with r2t_offset
before we updated our iterator and req->data_sent marker). This
can cause wrong offsets to be sent to the controller.

To fix that, we will first know that this may happen only in
the send sequence of the last page, hence we will take
the r2t_offset to the h2c PDU data_offset, and in
nvme_tcp_try_send_data loop, we make sure to increment
the request markers also when we completed a PDU but
we are expecting more r2t PDUs as we still did not send
the entire data of the request.

Fixes: 825619b09ad3 ("nvme-tcp: fix possible use-after-completion")
Reported-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Tested-by: Nowak, Lukasz <Lukasz.Nowak@Dell.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>

nvme-fc: remove freeze/unfreeze around update_nr_hw_queues

Remove the freeze/unfreeze around changes to the number of hardware
queues. Study and retest has indicated there are no ios that can be
active at this point so there is nothing to freeze.

nvme-fc is draining the queues in the shutdown and error recovery path
in __nvme_fc_abort_outstanding_ios.

This patch primarily reverts 88e837ed0f1f "nvme-fc: wait for queues to
freeze before calling update_hr_hw_queues". It's not an exact revert as
it leaves the adjusting of hw queues only if the count changes.

Signed-off-by: James Smart <jsmart2021@gmail.com>
[dwagner: added explanation why no IO is pending]
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

nvme-fc: avoid race between time out and tear down

To avoid race between time out and tear down, in tear down process,
first we quiesce the queue, and then delete the timer and cancel
the time out work for the queue.

This patch merges the admin and io sync ops into the queue teardown logic
as shown in the RDMA patch 3017013dcc "nvme-rdma: avoid race between time
out and tear down". There is no teardown_lock in nvme-fc.

Signed-off-by: James Smart <jsmart2021@gmail.com>
Tested-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

nvme-fc: update hardware queues before using them

In case the number of hardware queues changes, we need to update the
tagset and the mapping of ctx to hctx first.

If we try to create and connect the I/O queues first, this operation
will fail (target will reject the connect call due to the wrong number
of queues) and hence we bail out of the recreate function. Then we
will to try the very same operation again, thus we don't make any
progress.

Signed-off-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Merge tag 'afs-fixes-20210913' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull AFS fixes from David Howells:
"Fixes for AFS problems that can cause data corruption due to
  interaction with another client modifying data cached locally:

   - When d_revalidating a dentry, don't look at the inode to which it
     points. Only check the directory to which the dentry belongs. This
     was confusing things and causing the silly-rename cleanup code to
     remove the file now at the dentry of a file that got deleted.

   - Fix mmap data coherency. When a callback break is received that
     relates to a file that we have cached, the data content may have
     been changed (there are other reasons, such as the user's rights
     having been changed). However, we're checking it lazily, only on
     entry to the kernel, which doesn't happen if we have a writeable
     shared mapped page on that file.

     We make the kernel keep track of mmapped files and clear all PTEs
     mapping to that file as soon as the callback comes in by calling
     unmap_mapping_pages() (we don't necessarily want to zap the
     pagecache). This causes the kernel to be reentered when userspace
     tries to access the mmapped address range again - and at that point
     we can query the server and, if we need to, zap the page cache.

     Ideally, I would check each file at the point of notification, but
     that involves poking the server[*] - which is holding an exclusive
     lock on the vnode it is changing, waiting for all the clients it
     notified to reply. This could then deadlock against the server.
     Further, invalidating the pagecache might call ->launder_page(),
     which would try to write to the file, which would definitely
     deadlock. (AFS doesn't lease file access).

     [*] Checking to see if the file content has changed is a matter of
         comparing the current data version number, but we have to ask
         the server for that. We also need to get a new callback promise
         and we need to poke the server for that too.

   - Add some more points at which the inode is validated, since we're
     doing it lazily, notably in ->read_iter() and ->page_mkwrite(), but
     also when performing some directory operations.

     Ideally, checking in ->read_iter() would be done in some derivation
     of filemap_read(). If we're going to call the server to read the
     file, then we get the file status fetch as part of that.

   - The above is now causing us to make a lot more calls to
     afs_validate() to check the inode - and afs_validate() takes the
     RCU read lock each time to make a quick check (ie.
     afs_check_validity()). This is entirely for the purpose of checking
     cb_s_break to see if the server we're using reinitialised its list
     of callbacks - however this isn't a very common event, so most of
     the time we're taking this needlessly.

     Add a new cell-wide counter to count the number of
     reinitialisations done by any server and check that - and only if
     that changes, take the RCU read lock and check the server list (the
     server list may change, but the cell a file is part of won't).

   - Don't update vnode->cb_s_break and ->cb_v_break inside the validity
     checking loop. The cb_lock is done with read_seqretry, so we might
     go round the loop a second time after resetting those values - and
     that could cause someone else checking validity to miss something
     (I think).

  Also included are patches for fixes for some bugs encountered whilst
  debugging this:

   - Fix a leak of afs_read objects and fix a leak of keys hidden by
     that.

   - Fix a leak of pages that couldn't be added to extend a writeback.

   - Fix the maintenance of i_blocks when i_size is changed by a local
     write or a local dir edit"

Link: https://bugzilla.kernel.org/show_bug.cgi?id=214217
Link: https://lore.kernel.org/r/163111665183.283156.17200205573146438918.stgit@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/163113612442.352844.11162345591911691150.stgit@warthog.procyon.org.uk/
* tag 'afs-fixes-20210913' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Fix updating of i_blocks on file/dir extension
  afs: Fix corruption in reads at fpos 2G-4G from an OpenAFS server
  afs: Try to avoid taking RCU read lock when checking vnode validity
  afs: Fix mmap coherency vs 3rd-party changes
  afs: Fix incorrect triggering of sillyrename on 3rd-party invalidation
  afs: Add missing vnode validation checks
  afs: Fix page leak
  afs: Fix missing put on afs_read objects and missing get on the key therein

Merge tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd

Pull ksmbd server fixes from Steve French:
"Three ksmbd fixes, including an important security fix for path
  processing, and a buffer overflow check, and a trivial fix for
  incorrect header inclusion"

* tag '5.15-rc1-ksmbd' of git://git.samba.org/ksmbd:
  ksmbd: add validation for FILE_FULL_EA_INFORMATION of smb2_get_info
  ksmbd: prevent out of share access
  ksmbd: transport_rdma: Don't include rwlock.h directly