Antoine Tenart [Fri, 4 May 2018 15:21:03 +0000 (17:21 +0200)]
net: phy: sfp: handle cases where neither BR, min nor BR, max is given
When computing the bitrate using values read from an SFP module EEPROM,
we use the nominal BR plus BR,min and BR,max to determine the
boundaries. But in some cases BR,min and BR,max aren't provided, which
led the SFP code to end up having the nominal value for both the minimum
and maximum bitrate values. When using a passive cable, the nominal
value should be used as the maximum one, and there is no minimum one
so we should use 0.
Linus Torvalds [Tue, 8 May 2018 15:40:17 +0000 (05:40 -1000)]
Merge branch 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"An earlier commit to add reset control for embedded ahci controllers
affected some of the hardware specific drivers and got reverted for
now.
Other than that, just per-device workarounds and trivial changes"
* 'for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
driver core: add __printf verification to __ata_ehi_pushv_desc
ata: fix spelling mistake: "directon" -> "direction"
libata: Apply NOLPM quirk for SanDisk SD7UB3Q*G1001 SSDs
libata: Apply NOLPM quirk for SAMSUNG MZMPC128HBFU-000MV SSD
ata: ahci: mvebu: override ahci_stop_engine for mvebu AHCI
libahci: Allow drivers to override stop_engine
Revert "ata: ahci-platform: add reset control support"
Linus Torvalds [Tue, 8 May 2018 15:37:17 +0000 (05:37 -1000)]
Merge tag 'pinctrl-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes.
The Intel fixes are the most serious and important things I had queued
since it affects a large portion of deployed Chromebooks.
- Two major fixes for the Intel Cherryview and Sunrisepoint pin
controllers, adjusting numberspaces so that they get aligned with
various messed-up numbers encoded into the BIOS.
- A fix for the Meson driver GPIO pin range"
* tag 'pinctrl-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunrisepoint: Align GPIO number space with Windows
pinctrl: cherryview: Associate IRQ descriptors to irqdomain
pinctrl: meson-axg: fix the range of aobus bank
Linus Torvalds [Tue, 8 May 2018 15:35:12 +0000 (05:35 -1000)]
Merge tag 'gpio-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Sorry for lagging behind on sending the first batch of GPIO fixes for
this cycle. Just too busy conferencing and the weather was too nice.
Here it is anyway: some real important polishing on the error path
facing userspace (tagged for stable as well) and some normal driver
fixes.
- Fix proper IRQ unmasking in the Aspeed driver.
- Do not free unrequested descriptors on the errorpath when creating
line handles from the userspace chardev requested GPIO lines.
- Also fix the errorpath in the linehandle creation function.
- Fix the get/set multiple GPIO lines for a few of the funky
industrial GPIO cards on the ISA bus"
* tag 'gpio-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pcie-idio-24: Fix off-by-one error in get_multiple loop
gpio: pcie-idio-24: Fix port memory offset for get_multiple/set_multiple callbacks
gpio: pci-idio-16: Fix port memory offset for get_multiple callback
gpio: fix error path in lineevent_create
gpioib: do not free unrequested descriptors
gpio: fix aspeed_gpio unmask irq
David S. Miller [Tue, 8 May 2018 14:19:53 +0000 (10:19 -0400)]
Merge tag 'linux-can-fixes-for-4.17-20180508' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2018-05-08
this is a pull request for 7 patches for net/master.
The first patch is by Jakob Unterwurzacher and increases the severity of
bus-off messages in the generic CAN device infrastructure. The next two patches
are by Uwe Kleine-König and fix the endianess detection in the flexcan driver.
Jimmy Assarsson's patch for the kvaser driver corrects the stats counter for
dropped tx-messages. Geert Uytterhoeven provides one patch and Sergei Shtylyov
two patches for the rcan_canfd device tree binding description.
====================
Two fixes for the mcr20a driver, which was being added in the 4.17 merge window,
by Gustavo and myself.
The atusb driver got a change to GFP_KERNEL where no GFP_ATOMIC is needed by
Jia-Ju.
The last and most important fix is from Alex to get IPv6 reassembly working
again for the ieee802154 6lowpan adaptation. This got broken in 4.16 so please
queue this one also up for the 4.16 stable tree.
====================
David S. Miller [Tue, 8 May 2018 14:14:22 +0000 (10:14 -0400)]
Merge branch 'bnxt_en-Fixes-for-net-next'
Michael Chan says:
====================
bnxt_en: Fixes for net-next.
This series includes a bug fix for a regression in firmware message polling
introduced recently on net-next. There are 3 additional minor fixes for
unsupported link speed checking, VF MAC address handling, and setting
PHY eeprom length.
====================
Michael Chan [Tue, 8 May 2018 07:18:41 +0000 (03:18 -0400)]
bnxt_en: Always forward VF MAC address to the PF.
The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
bnxt_en: Read phy eeprom A2h address only when optical diagnostics is supported.
For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.
Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Michael Chan [Tue, 8 May 2018 07:18:39 +0000 (03:18 -0400)]
bnxt_en: Check unsupported speeds in bnxt_update_link() on PF only.
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression. With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.
Increase the maximum wait time from 5 usec to 20 usec. Also, fix
the debug message that shows the total delay time for the response
when the message times out. With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
drm/i915: Fix drm:intel_enable_lvds ERROR message in kernel log
Fix `[drm:intel_enable_lvds] *ERROR* timed out waiting for panel to
power on` in kernel log at boot time.
Toshiba Satellite Z930 laptops needs between 1 and 2 seconds to power
on its screen during Intel i915 DRM initialization. This currently
results in a `[drm:intel_enable_lvds] *ERROR* timed out waiting for
panel to power on` message appearing in the kernel log during boot
time and when stopping the machine.
This change increases the timeout of the `intel_enable_lvds` function
from 1 to 5 seconds, letting enough time for the Satellite 930 LCD
screen to power on, and suppressing the error message from the kernel
log.
This patch has been successfully tested on Linux 4.14 running on a
Toshiba Satellite Z930.
[vsyrjala: bump the timeout from 2 to 5 seconds to match the DP
code and properly cover the max hw timeout of ~4 seconds, and
drop the comment about the specific machine since this is not
a particulary surprising issue, nor specific to that one machine]
Ville Syrjälä [Thu, 26 Apr 2018 16:30:15 +0000 (19:30 +0300)]
drm/i915: Correctly populate user mode h/vdisplay with pipe src size during readout
During state readout we first read out the pipe src size, store
that information in the user mode h/vdisplay, but later on we overwrite
that with the actual crtc timings. That makes our read out crtc state
inconsistent with itself when the BIOS has enabled the panel fitter to
scale the pipe contents. Let's preserve the pipe src size based
information in the user mode to make things consistent again.
This fixes a problem introduced by commit a2936e3d9a9c ("drm/i915:
Use drm_mode_get_hv_timing() to populate plane clip rectangle")
where the inconsistent state is now leading the plane clipping code
to report a failure on account the plane dst coordinates not matching
the user mode size. Previously we did the plane clipping based on
the pipe src size instead and thus never noticed the inconsistency.
The failure manifests as a WARN:
[ 0.762117] [drm:intel_dump_pipe_config [i915]] requested mode:
[ 0.762142] [drm:drm_mode_debug_printmodeline [drm]] Modeline 0:"1366x768" 60 72143 1366 1414 1446 1526 768 771 777 784 0x40 0xa
...
[ 0.762327] [drm:intel_dump_pipe_config [i915]] port clock: 72143, pipe src size: 1024x768, pixel rate 72143
...
[ 0.764666] [drm:drm_atomic_helper_check_plane_state [drm_kms_helper]] Plane must cover entire CRTC
[ 0.764690] [drm:drm_rect_debug_print [drm]] dst: 1024x768+0+0
[ 0.764711] [drm:drm_rect_debug_print [drm]] clip: 1366x768+0+0
[ 0.764713] ------------[ cut here ]------------
[ 0.764714] Could not determine valid watermarks for inherited state
[ 0.764792] WARNING: CPU: 4 PID: 159 at drivers/gpu/drm/i915/intel_display.c:14584 intel_modeset_init+0x3ce/0x19d0 [i915]
...
Rodrigo Vivi [Wed, 2 May 2018 17:52:55 +0000 (10:52 -0700)]
drm/i915: Adjust eDP's logical vco in a reliable place.
On intel_dp_compute_config() we were calculating the needed vco
for eDP on gen9 and we stashing it in
intel_atomic_state.cdclk.logical.vco
However few moments later on intel_modeset_checks() we fully
replace entire intel_atomic_state.cdclk.logical with
dev_priv->cdclk.logical fully overwriting the logical desired
vco for eDP on gen9.
So, with wrong VCO value we end up with wrong desired cdclk, but
also it will raise a lot of WARNs: On gen9, when we read
CDCLK_CTL to verify if we configured properly the desired
frequency the CD Frequency Select bits [27:26] == 10b can mean
337.5 or 308.57 MHz depending on the VCO. So if we have wrong
VCO value stashed we will believe the frequency selection didn't
stick and start to raise WARNs of cdclk mismatch.
arm: dts: imx[35]*: declare flexcan devices to be compatible to imx25's flexcan
Commit d50f4630c2e1 ("arm: dts: Remove p1010-flexcan compatible from imx
series dts") removed the fallback compatible "fsl,p1010-flexcan" from
the imx device trees. As the flexcan cores on i.MX25, i.MX35 and i.MX53
are identical, introduce the first as fallback for the two latter ones.
Fixes: d50f4630c2e1 ("arm: dts: Remove p1010-flexcan compatible from imx series dts") Signed-off-by: Uwe Kleine-König <[email protected]> Cc: linux-stable <[email protected]> # >= v4.16 Signed-off-by: Marc Kleine-Budde <[email protected]>
In commit 88462d2a7830 ("can: flexcan: Remodel FlexCAN register r/w APIs
for big endian FlexCAN controllers.") the following logic was
implemented:
if the dt property "big-endian" is given or
the device is compatible to "fsl,p1010-flexcan":
use big-endian mode;
else
use little-endian mode;
This relies on commit d50f4630c2e1 ("arm: dts: Remove p1010-flexcan
compatible from imx series dts") which was applied a few commits later.
Without this commit (or an old device tree used for booting a new
kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match
the 'the device is compatible to "fsl,p1010-flexcan"' test and so are
switched erroneously to big endian mode.
Instead of the check above put a quirk in devtype data and rely on
of_match_device yielding the most compatible match
bus-off is usually caused by hardware malfunction or configuration error
(baud rate mismatch) and causes a complete loss of communication.
Increase the "bus-off" message's severity from netdev_dbg() to
netdev_info() to make it visible to the user.
A can interface going into bus-off is similar in severity to ethernet's
"Link is Down" message, which is also printed at info level.
It is debatable whether the the "restarted" message should also be
changed to netdev_info() to make the interface state changes
comprehensible from the kernel log. I have chosen to keep the
"restarted" message at dbg for now as the "bus-off" message should be
enough for the user to notice and investigate the problem.
The build is failing with CONFIG_NUMA=n and some compiler versions:
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_online_cpu':
hotplug-cpu.c:(.text+0x12c): undefined reference to `timed_topology_update'
arch/powerpc/platforms/pseries/hotplug-cpu.o: In function `dlpar_cpu_remove':
hotplug-cpu.c:(.text+0x400): undefined reference to `timed_topology_update'
Fix it by moving the empty version of timed_topology_update() into the
existing #ifdef block, which has the right guard of SPLPAR && NUMA.
Fixes: cee5405da402 ("powerpc/hotplug: Improve responsiveness of hotplug change") Signed-off-by: Michael Ellerman <[email protected]>
Zhao Chen [Mon, 7 May 2018 13:21:57 +0000 (09:21 -0400)]
net-next/hinic: add pci device ids for 25ge and 100ge card
This patch adds PCI device IDs to support 25GE and 100GE card:
1. Add device id 0x0201 for HINIC 100GE dual port card.
2. Add device id 0x0200 for HINIC 25GE dual port card.
3. Macro of device id 0x1822 is modified for HINIC 25GE quad port card.
Igor Russkikh [Mon, 7 May 2018 13:10:39 +0000 (16:10 +0300)]
net: aquantia: Limit number of vectors to actually allocated irqs
Driver should use pci_alloc_irq_vectors return value to correct number
of allocated vectors and napi instances. Otherwise it'll panic later
in pci_irq_vector.
Driver also should allow more than one MSI vectors to be allocated.
Error return path from pci_alloc_irq_vectors is also fixed to revert
resources in a correct sequence when error happens.
Reported-by: Long, Nicholas <[email protected]> Fixes: 23ee07a ("net: aquantia: Cleanup pci functions module") Signed-off-by: Igor Russkikh <[email protected]> Signed-off-by: David S. Miller <[email protected]>
MAINTAINERS: Update the 3c59x network driver entry
Replace my old E-Mail address with a working one.
While at it, change the maintainance status to
'Odd Fixes'. I'm still around with some knowledge,
but don't actively maintain it anymore.
Paolo Abeni [Fri, 4 May 2018 09:32:59 +0000 (11:32 +0200)]
net: core: rework basic flow dissection helper
When the core networking needs to detect the transport offset in a given
packet and parse it explicitly, a full-blown flow_keys struct is used for
storage.
This patch introduces a smaller keys store, rework the basic flow dissect
helper to use it, and apply this new helper where possible - namely in
skb_probe_transport_header(). The used flow dissector data structures
are renamed to match more closely the new role.
The above gives ~50% performance improvement in micro benchmarking around
skb_probe_transport_header() and ~30% around eth_get_headlen(), mostly due
to the smaller memset. Small, but measurable improvement is measured also
in macro benchmarking.
v1 -> v2: use the new helper in eth_get_headlen() and skb_get_poff(),
as per DaveM suggestion
David S. Miller [Tue, 8 May 2018 03:50:28 +0000 (23:50 -0400)]
Merge branch 'ipv6-misc'
Tariq Toukan says:
====================
net/ipv6 misc
This patchset contains two patches for net/ipv6.
Patch 1 is a trivial typo fix in documentation.
Patch 2 by Eran is a re-spin. It adds GRO support for IPv6 GRE tunnel,
this significantly improves performance in case GRO in native interface
is disabled.
====================
Eran Ben Elisha [Mon, 7 May 2018 07:45:27 +0000 (10:45 +0300)]
net: ipv6/gre: Add GRO support
Add GRO capability for IPv6 GRE tunnel and ip6erspan tap, via gro_cells
infrastructure.
Performance testing: 55% higher badwidth.
Measuring bandwidth of 1 thread IPv4 TCP traffic over IPv6 GRE tunnel
while GRO on the physical interface is disabled.
CPU: Intel Xeon E312xx (Sandy Bridge)
NIC: Mellanox Technologies MT27700 Family [ConnectX-4]
Before (GRO not working in tunnel) : 2.47 Gbits/sec
After (GRO working in tunnel) : 3.85 Gbits/sec
Andre Tomt [Mon, 7 May 2018 02:24:39 +0000 (04:24 +0200)]
net/tls: Fix connection stall on partial tls record
In the case of writing a partial tls record we forgot to clear the
ctx->in_tcp_sendpages flag, causing some connections to stall.
Fixes: c212d2c7fc47 ("net/tls: Don't recursively call push_record during tls_write_space callbacks") Signed-off-by: Andre Tomt <[email protected]> Signed-off-by: David S. Miller <[email protected]>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
qed: Add support for multi function mode with 802.1ad tagging.
The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Andrew Lunn [Sat, 5 May 2018 18:58:22 +0000 (20:58 +0200)]
net: dsa: mv88e6xxx: Fix PHY interrupts by parameterising PHY base address
Most of the mv88e6xxx switches have the PHYs at address 0, 1, 2, ...
The 6341 however has the PHYs at 0x10, 0x11, 0x12. Add a parameter to
the info structure for this base address.
Testing of 6f88284f3bd7 ("net: dsa: mv88e6xxx: Add MDIO interrupts for
internal PHYs") was performed on the 6341. So it works only on the
6341. Use this base information to correctly set the interrupt.
Fixes: 6f88284f3bd7 ("net: dsa: mv88e6xxx: Add MDIO interrupts for internal PHYs") Signed-off-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Eric Dumazet [Sat, 5 May 2018 15:35:04 +0000 (08:35 -0700)]
tls: fix use after free in tls_sk_proto_close
syzbot reported a use-after-free in tls_sk_proto_close
Add a boolean value to cleanup a bit this function.
BUG: KASAN: use-after-free in tls_sk_proto_close+0x8ab/0x9c0 net/tls/tls_main.c:297
Read of size 1 at addr ffff8801ae40a858 by task syz-executor363/4503
Xin Long [Sat, 5 May 2018 06:59:47 +0000 (14:59 +0800)]
sctp: delay the authentication for the duplicated cookie-echo chunk
Now sctp only delays the authentication for the normal cookie-echo
chunk by setting chunk->auth_chunk in sctp_endpoint_bh_rcv(). But
for the duplicated one with auth, in sctp_assoc_bh_rcv(), it does
authentication first based on the old asoc, which will definitely
fail due to the different auth info in the old asoc.
The duplicated cookie-echo chunk will create a new asoc with the
auth info from this chunk, and the authentication should also be
done with the new asoc's auth info for all of the collision 'A',
'B' and 'D'. Otherwise, the duplicated cookie-echo chunk with auth
will never pass the authentication and create the new connection.
This issue exists since very beginning, and this fix is to make
sctp_assoc_bh_rcv() follow the way sctp_endpoint_bh_rcv() does
for the normal cookie-echo chunk to delay the authentication.
While at it, remove the unused params from sctp_sf_authenticate()
and define sctp_auth_chunk_verify() used for all the places that
do the delayed authentication.
v1->v2:
fix the typo in changelog as Marcelo noticed.
Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'. Thanks to Daniel for the merge resolution.
Weilin Chang [Fri, 4 May 2018 18:07:19 +0000 (11:07 -0700)]
liquidio: support use of ethtool to set link speed of CN23XX-225 cards
Support setting the link speed of CN23XX-225 cards (which can do 25Gbps or
10Gbps) via ethtool_ops.set_link_ksettings.
Also fix the function assigned to ethtool_ops.get_link_ksettings to use the
new link_ksettings api completely (instead of partially via
ethtool_convert_legacy_u32_to_link_mode).
Moritz Fischer [Fri, 4 May 2018 17:18:33 +0000 (10:18 -0700)]
net: nixge: Fix error path for obtaining mac address
Fix issue where nixge_get_nvmem_address() returns a non-NULL
return value on a failed nvmem_cell_get() that causes an invalid
access when error value encoded in pointer is dereferenced.
Furthermore ensure that buffer allocated by nvmem_cell_read()
actually gets kfreed() if the function succeeds.
Anders Roxell [Fri, 4 May 2018 16:47:25 +0000 (18:47 +0200)]
selftests: net: use TEST_PROGS_EXTENDED
When a script file that isn't generated uses the variable
TEST_GEN_PROGS_EXTENDED and a 'make -C tools/testing/selftests clean' is
performed the script file gets removed and git shows the file as
deleted. For script files that isn't generated TEST_PROGS_EXTENDED
should be used.
Fixes: 9faedd643fd9 ("selftests: net: add in_netns.sh TEST_GEN_PROGS_EXTENDED") Signed-off-by: Anders Roxell <[email protected]> Signed-off-by: David S. Miller <[email protected]>
====================
3c59x patches and the removal of an unused function
The first patch removes an unused function. The goal of remaining three
patches is to get rid of the local_irq_save() usage in the driver which
benefits -RT.
====================
When vortex_boomerang_interrupt() is invoked from vortex_tx_timeout() or
poll_vortex() interrupts must be disabled. This detaches the interrupt
disable logic from locking which requires patching for PREEMPT_RT.
The advantage of avoiding spin_lock_irqsave() in the interrupt handler is
minimal, but converting it removes all the extra code for callers which
come not from interrupt context.
Locking is done in the same way in _vortex_interrupt() and
_boomerang_interrupt(). To prevent duplication, move the locking into the
calling vortex_boomerang_interrupt() function.
net: 3com: 3c59x: Move boomerang/vortex conditional into function
If vp->full_bus_master_tx is set, vp->full_bus_master_rx is set as well
(see vortex_probe1()). Therefore the conditionals for the decision if
boomerang or vortex ISR is executed have the same result. Instead of
repeating the explicit conditional execution of the boomerang/vortex ISR,
move it into an own function.
net: u64_stats_sync: Remove functions without user
Commit 67db3e4bfbc9 ("tcp: no longer hold ehash lock while calling
tcp_get_info()") removes the only users of u64_stats_update_end/begin_raw()
without removing the function in header file.
Anders Roxell [Fri, 4 May 2018 09:17:25 +0000 (11:17 +0200)]
selftests: net: add udpgso* to TEST_GEN_FILES
The generated files udpgso* shouldn't be part of TEST_PROGS, they are
used by udpgso.sh and udpgsp_bench.sh. They should be added to the
TEST_GEN_FILES to get installed without being added to the main
run_kselftest.sh script.
Fixes: 3a687bef148d ("selftests: udp gso benchmark") Signed-off-by: Anders Roxell <[email protected]> Signed-off-by: David S. Miller <[email protected]>
x86/xen: Reset VCPU0 info pointer after shared_info remap
This patch fixes crashes during boot for HVM guests on older (pre HVM
vector callback) Xen versions. Without this, current kernels will always
fail to boot on those Xen versions.
During boot, the HYPERVISOR_shared_info page gets remapped to make it work
with KASLR. This means that any pointer derived from it needs to be
adjusted.
The only value that this applies to is the vcpu_info pointer for VCPU 0.
For PV and HVM with the callback vector feature, this gets done via the
smp_ops prepare_boot_cpu callback. Older Xen versions do not support the
HVM callback vector, so there is no Xen-specific smp_ops set up in that
scenario. So, the vcpu_info pointer for VCPU 0 never gets set to the proper
value, and the first reference of it will be bad. Fix this by resetting it
immediately after the remap.
David S. Miller [Mon, 7 May 2018 15:38:37 +0000 (11:38 -0400)]
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2018-05-07
Here are a few more Bluetooth fixes for the 4.17 kernel, all for the
btusb driver. Two relate to the needs_reset_resume table, and one is a
revert of a patch for Atheros 1525/QCA6174 which caused a regression for
some people.
====================
Tomi Valkeinen [Wed, 2 May 2018 09:11:57 +0000 (12:11 +0300)]
drm/omap: handle error if scale coefs are not found
If get_scale_coef functions fail, they return NULL, but we never check
the return value and could do a NULL deref. This should not happen as we
ought to validate the amount of scaling already earlier, but to be safe,
add the necessary check.
Tomi Valkeinen [Thu, 29 Mar 2018 10:40:36 +0000 (13:40 +0300)]
drm/omap: fix uninitialized ret variable
audio_config function for both HDMI4 and HDMI5 return uninitialized
value as the error code if the display is not currently enabled. For
some reason this has not caused any issues.
Dan Carpenter [Wed, 18 Apr 2018 14:29:37 +0000 (17:29 +0300)]
drm/omap: silence unititialized variable warning
Smatch complains that "area_free" could be used without being
initialized. This code is several years old and premusably works fine
so this can't be a very serious bug. But it's easy enough to silence
the warning. If "area_free" is false at the end of the function then
we return -ENOMEM.
Eric Anholt [Fri, 9 Mar 2018 23:32:56 +0000 (15:32 -0800)]
drm/vc4: Fix oops dereferencing DPI's connector since panel_bridge.
In the cleanup, I didn't notice that we needed to dereference the
connector for the bus_format. Fix the regression by looking up the
first (and only) connector attached to us, and assume that its
bus_format is what we want. Some day it would be good to have that
part of display_info attached to the bridge, instead.
Ville Syrjälä [Wed, 2 May 2018 18:32:47 +0000 (21:32 +0300)]
drm/atomic: Clean private obj old_state/new_state in drm_atomic_state_default_clear()
Clear the old_state and new_state pointers for private objects
in drm_atomic_state_default_clear(). We don't actually have
functions to get the new/old state for private objects so
getting access to the potentially stale pointers requires a
bit more manual labour than for other object types. But let's
clear the pointers for private objects as well, if only to
avoid future surprises when someone decides to add the functions
to get at them.
v2: Split private objs to a separate patch (Daniel)
Ville Syrjälä [Wed, 2 May 2018 18:32:47 +0000 (21:32 +0300)]
drm/atomic: Clean old_state/new_state in drm_atomic_state_default_clear()
Clear the old_state and new_state pointers for every object in
drm_atomic_state_default_clear(). Otherwise
drm_atomic_get_{new,old}_*_state() will hand out stale pointers to
anyone who hasn't first confirmed that the object is in fact part of
the current atomic transcation, if they are called after we've done
the ww backoff dance while hanging on to the same drm_atomic_state.
For example, handle_conflicting_encoders() looks like it could hit
this since it iterates the full connector list and just calls
drm_atomic_get_new_connector_state() for each.
And I believe we have now witnessed this happening at least once in
i915 check_digital_port_conflicts(). Commit 8b69449d2663 ("drm/i915:
Remove last references to drm_atomic_get_existing* macros") changed
the safe drm_atomic_get_existing_connector_state() to the unsafe
drm_atomic_get_new_connector_state(), which opened the doors for
this particular bug there as well.
v2: Split private objs out to a separate patch (Daniel)
Ilan Peer [Fri, 20 Apr 2018 10:49:20 +0000 (13:49 +0300)]
mac80211: Adjust SAE authentication timeout
The IEEE P802.11-REVmd D1.0 specification updated the SAE authentication
timeout to be 2000 milliseconds (see dot11RSNASAERetransPeriod). Update
the SAE timeout setting accordingly.
While at it, reduce some code duplication in the timeout configuration.
mac80211_hwsim: fix a possible memory leak in hwsim_new_radio_nl()
'hwname' should be freed before leaving from the error handling cases,
otherwise it will cause mem leak
Fixes: cb1a5bae5684 ("mac80211_hwsim: add permanent mac address option for new radios") Signed-off-by: YueHaibing <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
Naveen N. Rao [Fri, 4 May 2018 13:14:25 +0000 (18:44 +0530)]
powerpc/trace/syscalls: Update syscall name matching logic to account for ppc_ prefix
Some syscall entry functions on powerpc are prefixed with
ppc_/ppc32_/ppc64_ rather than the usual sys_/__se_sys prefix. fork(),
clone(), swapcontext() are some examples of syscalls with such entry
points. We need to match against these names when initializing ftrace
syscall tracing.
Naveen N. Rao [Fri, 4 May 2018 13:14:24 +0000 (18:44 +0530)]
powerpc/trace/syscalls: Update syscall name matching logic
On powerpc64 ABIv1, we are enabling syscall tracing for only ~20
syscalls. This is due to commit e145242ea0df6 ("syscalls/core,
syscalls/x86: Clean up syscall stub naming convention") which has
changed the syscall entry wrapper prefix from "SyS" to "__se_sys".
Update the logic for ABIv1 to not just skip the initial dot, but also
the "__se_sys" prefix.
Fixes: commit e145242ea0df6 ("syscalls/core, syscalls/x86: Clean up syscall stub naming convention") Reported-by: Michael Ellerman <[email protected]> Signed-off-by: Naveen N. Rao <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
In commit 4e26bc4a4ed6 ("powerpc/64: Rename soft_enabled to
irq_soft_mask") we renamed paca->soft_enabled. But then in commit 8e0b634b1327 ("powerpc/64s: Do not allocate lppaca if we are not
virtualized") we added it back. Oops. This happened because the two
patches were in flight at the same time and rebased vs each other
multiple times, and we missed it in review.
Fixes: 8e0b634b1327 ("powerpc/64s: Do not allocate lppaca if we are not virtualized") Signed-off-by: Michael Ellerman <[email protected]>
Florent Fourcot [Sun, 6 May 2018 14:30:14 +0000 (16:30 +0200)]
netfilter: ctnetlink: export nf_conntrack_max
IPCTNL_MSG_CT_GET_STATS netlink command allow to monitor current number
of conntrack entries. However, if one wants to compare it with the
maximum (and detect exhaustion), the only solution is currently to read
sysctl value.
This patch add nf_conntrack_max value in netlink message, and simplify
monitoring for application built on netlink API.
Ahmed Abdelsalam [Wed, 25 Apr 2018 10:30:24 +0000 (05:30 -0500)]
netfilter: ip6t_srh: extend SRH matching for previous, next and last SID
IPv6 Segment Routing Header (SRH) contains a list of SIDs to be crossed
by SR encapsulated packet. Each SID is encoded as an IPv6 prefix.
When a Firewall receives an SR encapsulated packet, it should be able
to identify which node previously processed the packet (previous SID),
which node is going to process the packet next (next SID), and which
node is the last to process the packet (last SID) which represent the
final destination of the packet in case of inline SR mode.
An example use-case of using these features could be SID list that
includes two firewalls. When the second firewall receives a packet,
it can check whether the packet has been processed by the first firewall
or not. Based on that check, it decides to apply all rules, apply just
subset of the rules, or totally skip all rules and forward the packet to
the next SID.
This patch extends SRH match to support matching previous SID, next SID,
and last SID.
netfilter: nft_numgen: enable hashing of one element
The modulus in the hash function was limited to > 1 as initially
there was no sense to create a hashing of just one element.
Nevertheless, there are certain cases specially for load balancing
where this case needs to be addressed.
This patch fixes the following error.
Error: Could not process rule: Numerical result out of range
add rule ip nftlb lb01 dnat to jhash ip saddr mod 1 map { 0: 192.168.0.10 }
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The solution comes to force the hash to 0 when the modulus is 1.
Linus Torvalds [Sun, 6 May 2018 15:46:29 +0000 (05:46 -1000)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pll KVM fixes from Radim Krčmář:
"ARM:
- Fix proxying of GICv2 CPU interface accesses
- Fix crash when switching to BE
- Track source vcpu git GICv2 SGIs
- Fix an outdated bit of documentation
x86:
- Speed up injection of expired timers (for stable)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: remove APIC Timer periodic/oneshot spikes
arm64: vgic-v2: Fix proxying of cpuif access
KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance
KVM: arm64: Fix order of vcpu_write_sys_reg() arguments
KVM: arm/arm64: vgic: Fix source vcpu issues for GICv2 SGI
Linus Torvalds [Sun, 6 May 2018 15:42:24 +0000 (05:42 -1000)]
Merge tag 'iommu-fixes-v4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- fix a compile warning in the AMD IOMMU driver with irq remapping
disabled
- fix for VT-d interrupt remapping and invalidation size (caused a
BUG_ON when trying to invalidate more than 4GB)
- build fix and a regression fix for broken graphics with old DTS for
the rockchip iommu driver
- a revert in the PCI window reservation code which fixes a regression
with VFIO.
* tag 'iommu-fixes-v4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: rockchip: fix building without CONFIG_OF
iommu/vt-d: Use WARN_ON_ONCE instead of BUG_ON in qi_flush_dev_iotlb()
iommu/vt-d: fix shift-out-of-bounds in bug checking
iommu/dma: Move PCI window region reservation back into dma specific path.
iommu/rockchip: Make clock handling optional
iommu/amd: Hide unused iommu_table_lock
iommu/vt-d: Fix usage of force parameter in intel_ir_reconfigure_irte()
Linus Torvalds [Sun, 6 May 2018 15:37:24 +0000 (05:37 -1000)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"Unbreak the CPUID CPUID_8000_0008_EBX reload which got dropped when
the evaluation of physical and virtual bits which uses the same CPUID
leaf was moved out of get_cpu_cap()"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Restore CPUID_8000_0008_EBX reload
Linus Torvalds [Sun, 6 May 2018 15:35:23 +0000 (05:35 -1000)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clocksource fixes from Thomas Gleixner:
"The recent addition of the early TSC clocksource breaks on machines
which have an unstable TSC because in case that TSC is disabled, then
the clocksource selection logic falls back to the early TSC which is
obviously bogus.
That also unearthed a few robustness issues in the clocksource
derating code which are addressed as well"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Rework stale comment
clocksource: Consistent de-rate when marking unstable
x86/tsc: Fix mark_tsc_unstable()
clocksource: Initialize cs->wd_list
clocksource: Allow clocksource_mark_unstable() on unregistered clocksources
x86/tsc: Always unregister clocksource_tsc_early
Linus Torvalds [Sun, 6 May 2018 15:34:06 +0000 (05:34 -1000)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix to prevent false positives in the spurious interrupt
detector when more than a single demultiplex register is evaluated in
the Qualcom irq combiner driver"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/qcom: Fix check for spurious interrupts
projects / linux.git / log