Juergen Gross [Mon, 12 Jan 2015 05:05:08 +0000 (06:05 +0100)]
xen: correct race in alloc_p2m_pmd()
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Juergen Gross [Mon, 12 Jan 2015 05:05:07 +0000 (06:05 +0100)]
xen: correct error for building p2m list on 32 bits
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Jan Willeke [Thu, 8 Jan 2015 15:56:01 +0000 (16:56 +0100)]
s390/uprobes: fix user space PER events
If uprobes are single stepped for example with gdb, the behavior should
now be correct. Before this patch, when gdb was single stepping a uprobe,
the result was a SIGILL.
When PER is active for any storage alteration and a uprobe is hit, a storage
alteration event is indicated. These over indications are filterd out by gdb,
if no change has happened within the observed area.
Jeremiah Mahler [Sun, 11 Jan 2015 13:42:07 +0000 (05:42 -0800)]
usb: serial: handle -ENODEV quietly in generic_submit_read_urb
If a USB serial device (e.g. /dev/ttyUSB0) with an active program is
unplugged, an -ENODEV (19) error will be produced after it gives up
trying to resubmit a read.
Jeremiah Mahler [Sun, 11 Jan 2015 13:42:06 +0000 (05:42 -0800)]
usb: serial: silence all non-critical read errors
If a USB serial device is unplugged while there is an active program
using the device it may spam the logs with -EPROTO (71) messages as it
attempts to retry.
Most serial usb drivers (metro-usb, pl2303, mos7840, ...) only output
these messages for debugging. The generic driver treats these as
errors.
Change the default output for the generic serial driver from error to
debug to silence these non-critical errors.
mmc: sdhci: Fix sleep in atomic after inserting SD card
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Thomas Petazzoni [Wed, 31 Dec 2014 10:54:10 +0000 (11:54 +0100)]
mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
In commit 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller") Cc: <[email protected]> # v3.15+ Signed-off-by: Thomas Petazzoni <[email protected]> Signed-off-by: Ulf Hansson <[email protected]>
Adrian Hunter [Fri, 5 Dec 2014 17:25:31 +0000 (19:25 +0200)]
mmc: sdhci: Disable re-tuning for HS400
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Adrian Hunter [Fri, 5 Dec 2014 17:25:30 +0000 (19:25 +0200)]
mmc: sdhci: Simplify use of tuning timer
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Adrian Hunter [Fri, 5 Dec 2014 17:25:28 +0000 (19:25 +0200)]
mmc: sdhci: Tuning should not change max_blk_count
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
ARM: exynos_defconfig: Enable options for display panel support
Many Exynos devices have a display panel. Most of them just have
a simple panel while others have more complex configurations that
requires an embedded DisplayPort (eDP) to LVDS bridges.
This patch enables the following features to be built in the kernel
image to support both setups:
- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
powerpc: Work around gcc bug in current_thread_info()
In commit a3e5b356b3ab "powerpc: Don't use local named register variable
in current_thread_info" Anton changed the way we did current_thread_info()
to accommodate LLVM, and it was not meant to have any effect elsewhere.
Unfortunately it has exposed a gcc bug, where r1 gets copied into
another register and then gcc uses that register to restore the toc
after a function call, even when that register is volatile and has been
clobbered by the function call.
We could revert Anton's patch, but it's not clear the original code is
safe either, we may just have been lucky.
The cleanest solution is to just use the existing CURRENT_THREAD_INFO()
asm macro, and call it using inline asm.
Segher points out we don't need volatile on the asm, if the result of
the shift is unused it's fine for the compiler to elide it.
Fixes: a3e5b356b3ab ("powerpc: Don't use local named register variable in current_thread_info") Reported-by: Alexander Graf <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
Ian Munsie [Wed, 7 Jan 2015 05:33:04 +0000 (16:33 +1100)]
cxl: Fix issues when unmapping contexts
An issue was introduced with "cxl: Unmap MMIO regions when detaching a
context" (b123429e6a9e8d03aacf888d23262835f0081448) where closing a
context normally could also unmap the problem state area of other
contexts currently using the AFU.
It was also discovered that after a context's MMIO space had been
unmapped it would read 0s when accessing it, whereas the expected
behaviour was for the access to fail altogether.
In order to address these issues, this patch does two things:
- Forced mmap unmapping is only done when we are forcefully detaching
all contexts, and not in the normal detach path. Since the normal
context close path is tied to the file release any mmaps must have
already been released so we don't need to worry in that case.
- The mmap path now uses a vm_operations_struct with a fault handler.
The fault handler ensures that the context is in started state,
otherwise it fails the access attempt with a SIGBUS.
Fixes: b123429e6a9e ("cxl: Unmap MMIO regions when detaching a context") Signed-off-by: Ian Munsie <[email protected]> Signed-off-by: Michael Ellerman <[email protected]>
The store was originally used to save the current tracepoint status
so the entry and the exit tracepoints were always balanced. In the
end I just created a separate path when tracepoints are enabled.
The offset on the stack used for this store is not valid for ABIv2
and it causes strange issues. I noticed it because OPAL console input
was broken.
David S. Miller [Mon, 12 Jan 2015 05:23:45 +0000 (00:23 -0500)]
Merge tag 'wireless-drivers-for-davem-2015-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
* rtlwifi: fix a regression in large skb allocation failure
iwlwifi:
* fix for 7265D NVM check
* fixes for scan: fix long scanning times and network discovery
* new firmware API for iwlmvm supported devices
* fixes in rate control
Christoph Jaeger [Sun, 11 Jan 2015 18:01:16 +0000 (13:01 -0500)]
packet: bail out of packet_snd() if L2 header creation fails
Due to a misplaced parenthesis, the expression
(unlikely(offset) < 0),
which expands to
(__builtin_expect(!!(offset), 0) < 0),
never evaluates to true. Therefore, when sending packets with
PF_PACKET/SOCK_DGRAM, packet_snd() does not abort as intended
if the creation of the layer 2 header fails.
Spotted by Coverity - CID 1259975 ("Operands don't affect result").
Eric Dumazet [Sun, 11 Jan 2015 18:32:18 +0000 (10:32 -0800)]
alx: fix alx_poll()
Commit d75b1ade567f ("net: less interrupt masking in NAPI") uncovered
wrong alx_poll() behavior.
A NAPI poll() handler is supposed to return exactly the budget when/if
napi_complete() has not been called.
It is also supposed to return number of frames that were received, so
that netdev_budget can have a meaning.
Also, in case of TX pressure, we still have to dequeue received
packets : alx_clean_rx_irq() has to be called even if
alx_clean_tx_irq(alx) returns false, otherwise device is half duplex.
Linus Torvalds [Sun, 11 Jan 2015 20:44:10 +0000 (12:44 -0800)]
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"Three small fixes from over the Christmas period, and wiring up the
new execveat syscall for ARM"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
ARM: 8249/1: mm: dump: don't skip regions
ARM: wire up execveat syscall
Linus Torvalds [Sun, 11 Jan 2015 19:51:49 +0000 (11:51 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: group scheduling corner case fix, two deadline scheduler
fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
system fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
sched/deadline: Avoid double-accounting in case of missed deadlines
sched/deadline: Fix migration of SCHED_DEADLINE tasks
sched: Fix odd values in effective_load() calculations
sched, fanotify: Deal with nested sleeps
sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
Linus Torvalds [Sun, 11 Jan 2015 19:47:45 +0000 (11:47 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
Linus Torvalds [Sun, 11 Jan 2015 19:46:31 +0000 (11:46 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"A liblockdep fix and a mutex_unlock() mutex-debugging fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Always clear owner field upon mutex_unlock()
tools/liblockdep: Fix debug_check thinko in mutex destroy
mm: fix corner case in anon_vma endless growing prevention
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208e662 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Linus Torvalds [Sun, 11 Jan 2015 19:33:57 +0000 (11:33 -0800)]
mm: Don't count the stack guard page towards RLIMIT_STACK
Commit fee7e49d4514 ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions. It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".
Somebody did notice. Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.
So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Johan Hovold [Mon, 5 Jan 2015 15:04:12 +0000 (16:04 +0100)]
USB: console: fix uninitialised ldisc semaphore
The USB console currently allocates a temporary fake tty which is used
to pass terminal settings to the underlying serial driver.
The tty struct is not fully initialised, something which can lead to a
lockdep warning (or worse) if a serial driver tries to acquire a
line-discipline reference:
usbserial: USB Serial support registered for pl2303
pl2303 1-2.1:1.0: pl2303 converter detected
usb 1-2.1: pl2303 converter now attached to ttyUSB0
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 68 Comm: udevd Tainted: G W 3.18.0-rc5 #10
[<c0016f04>] (unwind_backtrace) from [<c0013978>] (show_stack+0x20/0x24)
[<c0013978>] (show_stack) from [<c0449794>] (dump_stack+0x24/0x28)
[<c0449794>] (dump_stack) from [<c006f730>] (__lock_acquire+0x1e50/0x2004)
[<c006f730>] (__lock_acquire) from [<c0070128>] (lock_acquire+0xe4/0x18c)
[<c0070128>] (lock_acquire) from [<c027c6f8>] (ldsem_down_read_trylock+0x78/0x90)
[<c027c6f8>] (ldsem_down_read_trylock) from [<c027a1cc>] (tty_ldisc_ref+0x24/0x58)
[<c027a1cc>] (tty_ldisc_ref) from [<c0340760>] (usb_serial_handle_dcd_change+0x48/0xe8)
[<c0340760>] (usb_serial_handle_dcd_change) from [<bf000484>] (pl2303_read_int_callback+0x210/0x220 [pl2303])
[<bf000484>] (pl2303_read_int_callback [pl2303]) from [<c031624c>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c031624c>] (__usb_hcd_giveback_urb) from [<c0316fc0>] (usb_giveback_urb_bh+0x98/0xd4)
[<c0316fc0>] (usb_giveback_urb_bh) from [<c0042e44>] (tasklet_hi_action+0x9c/0x108)
[<c0042e44>] (tasklet_hi_action) from [<c0042380>] (__do_softirq+0x148/0x42c)
[<c0042380>] (__do_softirq) from [<c00429cc>] (irq_exit+0xd8/0x114)
[<c00429cc>] (irq_exit) from [<c007ae58>] (__handle_domain_irq+0x84/0xdc)
[<c007ae58>] (__handle_domain_irq) from [<c000879c>] (omap_intc_handle_irq+0xd8/0xe0)
[<c000879c>] (omap_intc_handle_irq) from [<c0014544>] (__irq_svc+0x44/0x7c)
Exception stack(0xdf4e7f08 to 0xdf4e7f50)
7f00: debc0b80df4e7f5c0000000000000000debc0b80be8da96c
7f20: 0000000000000128c000fc84df4e600000000000df4e7f9400000004df4e7f50
7f40: c038ebc0c038d74c600f0013ffffffff
[<c0014544>] (__irq_svc) from [<c038d74c>] (___sys_sendmsg.part.29+0x0/0x2e0)
[<c038d74c>] (___sys_sendmsg.part.29) from [<c038ec08>] (SyS_sendmsg+0x18/0x1c)
[<c038ec08>] (SyS_sendmsg) from [<c000fa00>] (ret_fast_syscall+0x0/0x48)
console [ttyUSB0] enabled
Fixes: 36697529b5bb ("tty: Replace ldisc locking with ldisc_sem") Cc: stable <[email protected]> Signed-off-by: Johan Hovold <[email protected]>
Linus Torvalds [Sat, 10 Jan 2015 05:23:27 +0000 (21:23 -0800)]
Merge tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All a few small regression or stable fixes: a Nvidia HDMI ID addition,
a regression fix for CAIAQ stream count, a typo fix for GPIO setup
with STAC/IDT HD-audio codecs, and a Fireworks big-endian fix"
* tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireworks: fix an endianness bug for transaction length
ALSA: hda - Add new GPU codec ID 0x10de0072 to snd-hda
ALSA: hda - Fix wrong gpio_dir & gpio_mask hint setups for IDT/STAC codecs
ALSA: snd-usb-caiaq: fix stream count check
Linus Torvalds [Sat, 10 Jan 2015 05:18:48 +0000 (21:18 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- bounds checking fixes in logitech and roccat drivers, from Peter Wu
and Dan Carpenter
- double-kfree fix in i2c-hid driver on bus shutdown, from Mika
Westerberg
- a couple of various small driver fixes
- a few device id additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: roccat: potential out of bounds in pyra_sysfs_write_settings()
HID: Add a new id 0x501a for Genius MousePen i608X
HID: logitech-hidpp: prefix the name with "Logitech"
HID: logitech-hidpp: avoid unintended fall-through
HID: Allow HID_BATTERY_STRENGTH to be enabled
HID: i2c-hid: Do not free buffers in i2c_hid_stop()
HID: add battery quirk for USB_DEVICE_ID_APPLE_ALU_WIRELESS_2011_ISO keyboard
HID: logitech-hidpp: check WTP report length
HID: logitech-dj: check report length
Linus Torvalds [Sat, 10 Jan 2015 05:13:34 +0000 (21:13 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I'm briefly working between holidays and LCA, so this is close to a
couple of weeks of fixes,
Two sets of amdkfd fixes, this is a new feature this kernel, and this
pull fixes a few issues since it got merged, ordering when built-in to
kernel and also the iommu vs gpu ordering patch, it also reworks the
ioctl before the initial release.
Otherwise:
- radeon: some misc fixes all over, hdmi, 4k, dpm
- nouveau: mcp77 init fixes, oops fix, bug on fix, msi fix
- i915: power fixes, revert VGACNTR patch
Probably be quiteer next week since I'll be at LCA anyways"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm/amdkfd: rewrite kfd_ioctl() according to drm_ioctl()
drm/amdkfd: reformat IOCTL definitions to drm-style
drm/amdkfd: Do copy_to/from_user in general kfd_ioctl()
drm/radeon: integer underflow in radeon_cp_dispatch_texture()
drm/radeon: adjust default bapm settings for KV
drm/radeon: properly filter DP1.2 4k modes on non-DP1.2 hw
drm/radeon: fix sad_count check for dce3
drm/radeon: KV has three PPLLs (v2)
drm/amdkfd: unmap VMID<-->PASID when relesing VMID (non-HWS)
drm/radeon: Init amdkfd only if it was compiled
amdkfd: actually allocate longs for the pasid bitmask
drm/nouveau/nouveau: Do not BUG_ON(!spin_is_locked()) on UP
drm/nv4c/mc: disable msi
drm/nouveau/fb/ram/mcp77: enable NISO poller
drm/nouveau/fb/ram/mcp77: use carveout reg to determine size
drm/nouveau/fb/ram/mcp77: subclass nouveau_ram
drm/nouveau: wake up the card if necessary during gem callbacks
drm/nouveau/device: Add support for GK208B, resolves bug 86935
drm/nouveau: fix missing return statement in nouveau_ttm_tt_unpopulate
drm/nouveau/bios: fix oops on pre-nv50 chipsets
...
Linus Torvalds [Sat, 10 Jan 2015 04:57:58 +0000 (20:57 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here is a handful of minor arm64 fixes discovered and fixed over the
Christmas break. The main part is adding some missing #includes that
we seem to be getting transitively but have started causing problems
in -next.
- Fix early mapping fixmap corruption by EFI runtime services
- Fix __NR_compat_syscalls off-by-one
- Add missing sanity checks for some 32-bit registers
- Add some missing #includes which we get transitively
- Remove unused prepare_to_copy() macro"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/efi: add missing call to early_ioremap_reset()
arm64: fix missing asm/io.h include in kernel/smp_spin_table.c
arm64: fix missing asm/alternative.h include in kernel/module.c
arm64: fix missing linux/bug.h include in asm/arch_timer.h
arm64: fix missing asm/pgtable-hwdef.h include in asm/processor.h
arm64: sanity checks: add missing AArch32 registers
arm64: Remove unused prepare_to_copy()
arm64: Correct __NR_compat_syscalls for bpf
Fixes
- kgdb/kdb: Allow access on a single core, if a CPU round up is
deemed impossible, which will allow inspection of the now "trashed"
kernel
- kdb: Add enable mask for the command groups
- kdb: access controls to restrict sensitive commands"
* tag 'for_linus-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kernel/debug/debug_core.c: Logging clean-up
kgdb: timeout if secondary CPUs ignore the roundup
kdb: Allow access to sensitive commands to be restricted by default
kdb: Add enable mask for groups of commands
kdb: Categorize kdb commands (similar to SysRq categorization)
kdb: Remove KDB_REPEAT_NONE flag
kdb: Use KDB_REPEAT_* values as flags
kdb: Rename kdb_register_repeat() to kdb_register_flags()
kdb: Rename kdb_repeat_t to kdb_cmdflags_t, cmd_repeat to cmd_flags
kdb: Remove currently unused kdbtab_t->cmd_flags
Linus Torvalds [Sat, 10 Jan 2015 01:55:00 +0000 (17:55 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two Ceph fixes from Sage Weil:
"These are both pretty trivial: a sparse warning fix and size_t printk
thing"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix sparse endianness warnings
ceph: use %zu for len in ceph_fill_inline_data()
Linus Torvalds [Sat, 10 Jan 2015 01:46:07 +0000 (17:46 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"None of these are huge, but my commit does fix a regression from 3.18
that could cause lost files during log replay.
This also adds Dave Sterba to the list of Btrfs maintainers. It
doesn't mean we're doing things differently, but Dave has really been
helping with the maintainer workload for years"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: don't delay inode ref updates during log replay
Btrfs: correctly get tree level in tree_backref_for_extent
Btrfs: call inode_dec_link_count() on mkdir error path
Btrfs: abort transaction if we don't find the block group
Btrfs, scrub: uninitialized variable in scrub_extent_for_parity()
Btrfs: add more maintainers
Songjun Wu [Fri, 9 Jan 2015 16:11:24 +0000 (17:11 +0100)]
usb: gadget: udc: atmel: fix possible oops when unloading module
When unloading the module 'g_hid.ko', the urb request will be dequeued and the
completion routine will be excuted. If there is no urb packet, the urb request
will not be added to the endpoint queue and the completion routine pointer in
urb request is NULL.
Accessing to this NULL function pointer will cause the Oops issue reported
below.
Add the code to check if the urb request is in the endpoint queue
or not. If the urb request is not in the endpoint queue, a negative
error code will be returned.
Returning a difference from a comparison functions is usually wrong
(see acbbe6fbb240 "kcmp: fix standard comparison bug" for the long
story). Here there is the additional twist that if the void pointers
ns and kn->ns happen to differ by a multiple of 2^32,
kernfs_name_compare returns 0, falsely reporting a match to the
caller.
Technically 'hash - kn->hash' is ok since the hashes are restricted to
31 bits, but it's better to avoid that subtlety.
mcb: mcb-pci: Only remap the 1st 0x200 bytes of BAR 0
Currently it is not possible to have a kernel with built-in MCB attached
devices. This results out of the fact that mcb-pci requests PCI BAR 0, then
parses the chameleon table and calls the driver's probe function before
releasing BAR 0 again. When building the kernel with modules this is not a
problem (and therefore it wasn't detected by my tests yet).
A solution is to only remap the 1st 0x200 bytes of a Chameleon PCI device.
0x200 bytes is the maximum size of a Chameleon v2 Table.
Also this patch stops disabling the PCI device on successful registration of MCB
devices.
target: Drop left-over fabric_max_sectors attribute
Now that fabric_max_sectors is no longer used to enforce the maximum
I/O size, go ahead and drop it's left-over usage in target-core and
associated backend drivers.
This patch drops the arbitrary maximum I/O size limit in sbc_parse_cdb(),
which currently for fabric_max_sectors is hardcoded to 8192 (4 MB for 512
byte sector devices), and for hw_max_sectors is a backend driver dependent
value.
This limit is problematic because Linux initiators have only recently
started to honor block limits MAXIMUM TRANSFER LENGTH, and other non-Linux
based initiators (eg: MSFT Fibre Channel) can also generate I/Os larger
than 4 MB in size.
Currently when this happens, the following message will appear on the
target resulting in I/Os being returned with non recoverable status:
SCSI OP 28h with too big sectors 16384 exceeds fabric_max_sectors: 8192
Instead, drop both [fabric,hw]_max_sector checks in sbc_parse_cdb(),
and convert the existing hw_max_sectors into a purely informational
attribute used to represent the granuality that backend driver and/or
subsystem code is splitting I/Os upon.
Also, update FILEIO with an explicit FD_MAX_BYTES check in fd_execute_rw()
to deal with the one special iovec limitiation case.
v2 changes:
- Drop hw_max_sectors check in sbc_parse_cdb()
Linus Torvalds [Fri, 9 Jan 2015 23:10:59 +0000 (15:10 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"12 fixes"
* emailed patches from Andrew Morton <[email protected]>:
mm, vmscan: prevent kswapd livelock due to pfmemalloc-throttled process being killed
memcg: fix destination cgroup leak on task charges migration
mm: memcontrol: switch soft limit default back to infinity
mm/debug_pagealloc: remove obsolete Kconfig options
vfs: renumber FMODE_NONOTIFY and add to uniqueness check
arch/blackfin/mach-bf533/boards/stamp.c: add linux/delay.h
ocfs2: fix the wrong directory passed to ocfs2_lookup_ino_from_name() when link file
MAINTAINERS: update rydberg's addresses
mm: protect set_page_dirty() from ongoing truncation
mm: prevent endless growth of anon_vma hierarchy
exit: fix race between wait_consider_task() and wait_task_zombie()
ocfs2: remove bogus check in dlm_process_recovery_data
H_RST bit in H_CSR register may be found lit before reset is started,
for example if preceding reset flow hasn't completed.
In that case asserting H_RST will be ignored, therefore we need to clean
H_RST bit to start a successful reset sequence.
Peter Hurley [Tue, 30 Dec 2014 15:39:25 +0000 (10:39 -0500)]
tty: Prevent hw state corruption in exclusive mode reopen
Exclusive mode ttys (TTY_EXCLUSIVE) do not allow further reopens;
fail the condition before associating the file pointer and calling
the driver open() method.
Prevents DTR programming when the tty is already in exclusive mode.
In v3.19-rc3 tree when CONFIG_ARM_LPAE and CONFIG_DEBUG_RODATA are enabled
image failed to compile with the following error:
arch/arm/mm/init.c:661:14: error: ‘PMD_SECT_RDONLY’ undeclared here (not in a function)
It seems that '80d6b0c ARM: mm: allow text and rodata sections to be read-only'
and 'ded9477 ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE'
commits crossed. 80d6b0c uses PMD_SECT_RDONLY macro but ded9477 renames it
and uses software bits L_PMD_SECT_RDONLY instead.
Fix is to use L_PMD_SECT_RDONLY instead PMD_SECT_RDONLY as ded9477 does in
another places.
Maxime Ripard [Tue, 6 Jan 2015 15:45:07 +0000 (16:45 +0100)]
usb: phy: Fix deferred probing
Commit 1290a958d48e ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") actually broke the deferred probing mechanism, since it now returns
EPROBE_DEFER only when the try_module_get call fails, but not when the phy
lookup does.
All the other similar functions seem to return ENODEV when try_module_get
fails, and the error code of either __usb_find_phy or __of_usb_find_phy
otherwise.
In order to have a consistent behaviour, and a meaningful EPROBE_DEFER, always
return EPROBE_DEFER when __(of_)usb_find_phy fails to look up the requested
phy, that will be propagated by the caller, and ENODEV if try_module_get fails.
Arseny Solokha [Sat, 6 Dec 2014 02:54:06 +0000 (09:54 +0700)]
OHCI: add a quirk for ULi M5237 blocking on reset
Commit 8dccddbc2368 ("OHCI: final fix for NVIDIA problems (I hope)")
introduced into 3.1.9 broke boot on e.g. Freescale P2020DS development
board. The code path that was previously specific to NVIDIA controllers
had then become taken for all chips.
However, the M5237 installed on the board wedges solid when accessing
its base+OHCI_FMINTERVAL register, making it impossible to boot any
kernel newer than 3.1.8 on this particular and apparently other similar
machines.
Don't readl() and writel() base+OHCI_FMINTERVAL on PCI ID 10b9:5237.
The patch is suitable for the -next tree as well as all maintained
kernels up to 3.2 inclusive.
Hans de Goede [Thu, 8 Jan 2015 14:15:14 +0000 (15:15 +0100)]
uas: Do not blacklist ASM1153 disk enclosures
Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems
with newer ASM1153 disk enclosures in 2 ways:
1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which
we assume is always an ASM1051, so remove the quirk for 5106, and instead
use the same detection logic as we already use for device-id 55aa, which is
used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>.
2) Our detection logic to differentiate between ASM1051 and ASM1053 sees
ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs.
Luckily the ASM1153 descriptors are not 100% identical, unlike the previous
models the ASM1153 has bMaxPower == 0, so use that to differentiate it.
Vince Hsu [Wed, 24 Dec 2014 10:16:30 +0000 (18:16 +0800)]
usb: host: ehci-tegra: request deferred probe when failing to get phy
The commit 1290a958d48e ("usb: phy: propagate __of_usb_find_phy()'s error on
failure") changed the condition to return -EPROBE_DEFER to host driver.
Originally the Tegra host driver depended on the returned -EPROBE_DEFER to
get the phy device later when booting. Now we have to do that explicitly.
Darrick J. Wong [Thu, 11 Dec 2014 19:01:11 +0000 (11:01 -0800)]
uas: disable UAS on Apricorn SATA dongles
The Apricorn SATA dongle will occasionally return "USBSUSBSUSB" in
response to SCSI commands when running in UAS mode. Therefore,
disable UAS mode on this dongle.
Hans de Goede [Fri, 5 Dec 2014 10:11:28 +0000 (11:11 +0100)]
xhci: Add broken-streams quirk for Fresco Logic FL1000G xhci controllers
Streams do not work reliabe on Fresco Logic FL1000G xhci controllers,
trying to use them results in errors like this:
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b35709067b000000000000500000001078001
21:37:33 kernel: xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring
21:37:33 kernel: xhci_hcd 0000:04:00.0: @00000000368b35809067b400000000000500000001038001
As always I've ordered a pci-e addon card with a Fresco Logic controller for
myself to see if I can come up with a better fix then the big hammer, in
the mean time this will make uas devices work again (in usb-storage mode)
for FL1000G users.
Alan Stern [Thu, 4 Dec 2014 15:22:57 +0000 (10:22 -0500)]
USB: EHCI: adjust error return code
The USB stack uses error code -ENOSPC to indicate that the periodic
schedule is too full, with insufficient bandwidth to accommodate a new
allocation. It uses -EFBIG to indicate that an isochronous transfer
could not be linked into the schedule because it would exceed the
number of isochronous packets the host controller driver can handle
(generally because the new transfer would extend too far into the
future).
ehci-hcd uses the wrong error code at one point. This patch fixes it,
along with a misleading comment and debugging message.
Alan Stern [Thu, 4 Dec 2014 15:21:56 +0000 (10:21 -0500)]
USB: EHCI: fix initialization bug in iso_stream_schedule()
Commit c3ee9b76aa93 (EHCI: improved logic for isochronous scheduling)
introduced the idea of using ehci->last_iso_frame as the origin (or
base) for the circular calculations involved in modifying the
isochronous schedule. However, the new code it added used
ehci->last_iso_frame before the value was properly initialized. This
patch rectifies the mistake by moving the initialization lines earlier
in iso_stream_schedule().
Mathias Nyman [Fri, 9 Jan 2015 15:18:28 +0000 (17:18 +0200)]
xhci: Check if slot is already in default state before moving it there
Solves xhci error cases with debug messages:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 1-6: hub failed to enable device, error -22
xhci will give a context state error if we try to set a slot in default
state to the same default state with a special address device command.
Turns out this happends in several cases:
- retry reading the device rescriptor in hub_port_init()
- usb_reset_device() is called for a slot in default state
- in resume path, usb_port_resume() calls hub_port_init()
The default state is usually reached from most states with a reset device
command without any context state errors, but using the address device
command with BSA bit set (block set address) only works from the enabled
state and will otherwise cause context error.
solve this by checking if we are already in the default state before issuing
a address device BSA=1 command.
It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.
So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
The blk-mq ->queue_rq method is always called from process context,
but might have preemption disabled. This means we still always
have to use GFP_ATOMIC for memory allocations, and thus need to
revert part of commit 3c356bde1 ("scsi: stop passing a gfp_mask
argument down the command setup path").
Dan Carpenter [Fri, 9 Jan 2015 12:32:31 +0000 (15:32 +0300)]
HID: roccat: potential out of bounds in pyra_sysfs_write_settings()
This is a static checker fix. We write some binary settings to the
sysfs file. One of the settings is the "->startup_profile". There
isn't any checking to make sure it fits into the
pyra->profile_settings[] array in the profile_activated() function.
I added a check to pyra_sysfs_write_settings() in both places because
I wasn't positive that the other callers were correct.
Chris Wilson [Tue, 6 Jan 2015 10:29:35 +0000 (10:29 +0000)]
mutex: Always clear owner field upon mutex_unlock()
Currently if DEBUG_MUTEXES is enabled, the mutex->owner field is only
cleared iff debug_locks is active. This exposes a race to other users of
the field where the mutex->owner may be still set to a stale value,
potentially upsetting mutex_spin_on_owner() among others.
Tetsuo Handa [Thu, 25 Dec 2014 06:51:21 +0000 (15:51 +0900)]
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
When alloc_fair_sched_group() in sched_create_group() fails,
free_sched_group() is called, and free_fair_sched_group() is called by
free_sched_group(). Since destroy_cfs_bandwidth() is called by
free_fair_sched_group() without calling init_cfs_bandwidth(),
RCU stall occurs at hrtimer_cancel():
Luca Abeni [Wed, 17 Dec 2014 10:50:32 +0000 (11:50 +0100)]
sched/deadline: Avoid double-accounting in case of missed deadlines
The dl_runtime_exceeded() function is supposed to ckeck if
a SCHED_DEADLINE task must be throttled, by checking if its
current runtime is <= 0. However, it also checks if the
scheduling deadline has been missed (the current time is
larger than the current scheduling deadline), further
decreasing the runtime if this happens.
This "double accounting" is wrong:
- In case of partitioned scheduling (or single CPU), this
happens if task_tick_dl() has been called later than expected
(due to small HZ values). In this case, the current runtime is
also negative, and replenish_dl_entity() can take care of the
deadline miss by recharging the current runtime to a value smaller
than dl_runtime
- In case of global scheduling on multiple CPUs, scheduling
deadlines can be missed even if the task did not consume more
runtime than expected, hence penalizing the task is wrong
This patch fix this problem by throttling a SCHED_DEADLINE task
only when its runtime becomes negative, and not modifying the runtime
Luca Abeni [Wed, 17 Dec 2014 10:50:31 +0000 (11:50 +0100)]
sched/deadline: Fix migration of SCHED_DEADLINE tasks
According to global EDF, tasks should be migrated between runqueues
without checking if their scheduling deadlines and runtimes are valid.
However, SCHED_DEADLINE currently performs such a check:
a migration happens doing:
which ends up calling dequeue_task_dl(), setting the new CPU, and then
calling enqueue_task_dl().
enqueue_task_dl() then calls enqueue_dl_entity(), which calls
update_dl_entity(), which can modify scheduling deadline and runtime,
breaking global EDF scheduling.
As a result, some of the properties of global EDF are not respected:
for example, a taskset {(30, 80), (40, 80), (120, 170)} scheduled on
two cores can have unbounded response times for the third task even
if 30/80+40/80+120/170 = 1.5809 < 2
This can be fixed by invoking update_dl_entity() only in case of
wakeup, or if this is a new SCHED_DEADLINE task.
Yuyang Du [Fri, 19 Dec 2014 00:29:56 +0000 (08:29 +0800)]
sched: Fix odd values in effective_load() calculations
In effective_load, we have (long w * unsigned long tg->shares) / long W,
when w is negative, it is cast to unsigned long and hence the product is
insanely large. Fix this by casting tg->shares to long.
Peter Zijlstra [Tue, 16 Dec 2014 15:28:38 +0000 (16:28 +0100)]
sched, fanotify: Deal with nested sleeps
As per e23738a7300a ("sched, inotify: Deal with nested sleeps").
fanotify_read is a wait loop with sleeps in. Wait loops rely on
task_struct::state and sleeps do too, since that's the only means of
actually sleeping. Therefore the nested sleeps destroy the wait loop
state and the wait loop breaks the sleep functions that assume
TASK_RUNNING (mutex_lock).
Fix this by using the new woken_wake_function and wait_woken() stuff,
which registers wakeups in wait and thereby allows shrinking the
task_state::state changes to the actual sleep part.
Andy Lutomirski [Sun, 4 Jan 2015 18:36:20 +0000 (10:36 -0800)]
perf/x86_64: Improve user regs sampling
Perf reports user regs for kernel-mode samples so that samples can
be backtraced through user code. The old code was very broken in
syscall context, resulting in useless backtraces.
The new code, in contrast, is still dangerously racy, but it should
at least work most of the time.
Andy Lutomirski [Sun, 4 Jan 2015 18:36:19 +0000 (10:36 -0800)]
perf: Move task_pt_regs sampling into arch code
On x86_64, at least, task_pt_regs may be only partially initialized
in many contexts, so x86_64 should not use it without extra care
from interrupt context, let alone NMI context.
This will allow x86_64 to override the logic and will supply some
scratch space to use to make a cleaner copy of user regs.
Peter Zijlstra [Tue, 16 Dec 2014 10:46:14 +0000 (11:46 +0100)]
x86: Fix off-by-one in instruction decoder
Stephane reported that the PEBS fixup was broken by the recent commit to
the instruction decoder. The thing had an off-by-one which resulted in
not being able to decode the last instruction and always bail.
Ingo Molnar [Fri, 9 Jan 2015 10:04:13 +0000 (11:04 +0100)]
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Free callchains when hist entries are deleted, plugging a massive leak in
'top -g', where hist_entries (and its callchains) are decayed over time. (Namhyung Kim)
- Fix segfault when showing callchain in the hists browser (report & top) (Namhyung Kim)
- Fix children sort key behavior, and also the 'perf test 32' test that
was failing due to reliance on undefined behaviour (Namhyung Kim)
Michael Holzheu [Thu, 8 Jan 2015 13:46:18 +0000 (14:46 +0100)]
s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
Currently the signed COMPARE (cr) instruction is used to compare "A"
with "X". This is not correct because "A" and "X" are both unsigned.
To fix this use the unsigned COMPARE LOGICAL (clr) instruction instead.
Michael Holzheu [Thu, 8 Jan 2015 13:36:21 +0000 (14:36 +0100)]
s390/bpf: Fix ALU_NEG (A = -A)
Currently the LOAD NEGATIVE (lnr) instruction is used for ALU_NEG. This
instruction always loads the negative value. Therefore, if A is already
negative, it remains unchanged. To fix this use LOAD COMPLEMENT (lcr)
instead.
Octavian Purdila [Thu, 11 Dec 2014 13:02:30 +0000 (15:02 +0200)]
gpio: dln2: use bus_sync_unlock instead of scheduling work
Use the irq_chip bus_sync_unlock method to update hardware registers
instead of scheduling work from the mask/unmask methods. This simplifies
a bit the driver and make it more uniform with the other GPIO IRQ
drivers.
TRSCER register is configured differently by SoCs. TRSCER of R-Car Gen2 is
RINT8 bit only valid, other bits are reserved bits. This removes access to
TRSCER register reserve bit by adding variable trscer_err_mask to
sh_eth_cpu_data structure, set the register information to each SoCs.
FDR register of R-Car set in fdr_value can have the original settings.
This sets the value that is suitable for each SoCs to fdr_value of R8A777x
and R8A779x.
David S. Miller [Fri, 9 Jan 2015 03:40:52 +0000 (19:40 -0800)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-01-06
This series contains fixes to i40e only.
Jesse provides a fix for when the driver was polling with interrupts
disabled the hardware would occasionally not write back descriptors.
His fix causes the driver to detect this situation and force an interrupt
to fire which will flush the stuck descriptor.
Anjali provides a couple of fixes, the first corrects an issue where
the receive port checksum error counter was incrementing incorrectly with
UDP encapsulated tunneled traffic. The second fix resolves an issue where
the driver was examining the outer protocol layer to set the inner protocol
layer checksum offload. In the case of TCP over IPv6 over an IPv4 based
VXLAN, the inner checksum offloads would be set to look for IPv4/UDP
instead of IPv6/TCP, so fixed the issue so that the driver will look at
the proper layer for encapsulation offload settings.
v2: fixed a bug in patch 01 of the series, where the interrupt rate impacted
4 port workloads by reducing throughput.
====================
Merge tag 'iio-fixes-for-3.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.19 cycle.
* ad799x fix ad7991/ad7995/ad7999 setup as they do not have a configuration
register to write to. It is written during the convesion sequence. As
such we don't want to write to it at other times.
* Fix iio_channel_read utility function to return to ensure it is apparent
if the relevant element is not there. This avoids using a wrong value
if some channels have the element and others do not.
projects / linux.git / log