Thomas Gleixner [Mon, 22 Aug 2016 08:34:13 +0000 (10:34 +0200)]
Merge tag 'irqchip-for-4.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull genirq/irqchip fixes for 4.8-rc4 from Marc Zygnier
- A critical fix for chained irqchip where we failed to configure
the cascade interrupt trigger
- A GIC fix for self-IPI in SMP-on-UP configurations
- A PM fix for GICv3
- A initialization fix the the GICv3 ITS, triggered by kexec
Daniel Vetter [Sat, 20 Aug 2016 10:22:11 +0000 (12:22 +0200)]
drm: Reject page_flip for !DRIVER_MODESET
Somehow this one slipped through, which means drivers without modeset
support can be oopsed (since those also don't call
drm_mode_config_init, which means the crtc lookup will chase an
uninitalized idr).
Linus Torvalds [Sun, 21 Aug 2016 21:28:24 +0000 (14:28 -0700)]
Merge branch 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull two parisc fixes from Helge Deller:
"The first patch ensures that the high-res cr16 clocksource (which was
added in kernel 4.7) gets choosen as default clocksource for parisc.
The second patch moves the #define of EREFUSED down inside errno.h and
thus unbreaks building the gccgo compiler"
* 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix order of EREFUSED define in errno.h
parisc: Fix automatic selection of cr16 clocksource
Tony Luck [Sat, 20 Aug 2016 23:27:58 +0000 (16:27 -0700)]
EDAC, skx_edac: Add EDAC driver for Skylake
This is an entirely new driver instead of yet another set of patches
to sb_edac.c because:
1) Mapping from PCI devices to socket/memory controller is significantly
different. Skylake scatters devices on a socket across a number of
PCI buses.
2) There is an extra level of interleaving via the "mcroute" register
that would be a little messy to squeeze into the old driver.
3) Validation is getting too expensive. Changes to sb_edac need to
be checked against Sandy Bridge, Ivy Bridge, Haswell, Broadwell and
Knights Landing.
Helge Deller [Sat, 20 Aug 2016 09:51:38 +0000 (11:51 +0200)]
parisc: Fix order of EREFUSED define in errno.h
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Helge Deller [Fri, 19 Aug 2016 20:39:02 +0000 (22:39 +0200)]
parisc: Fix automatic selection of cr16 clocksource
Commit 54b66800907 (parisc: Add native high-resolution sched_clock()
implementation) added support to use the CPU-internal cr16 counters as reliable
clocksource with the help of HAVE_UNSTABLE_SCHED_CLOCK.
Sadly the commit missed to remove the hack which prevented cr16 to become the
default clocksource even on SMP systems.
Jens Axboe [Fri, 19 Aug 2016 20:03:05 +0000 (14:03 -0600)]
Merge branch 'v4.8-rc2-bcache-fixes' of https://bitbucket.org/ewheelerinc/linux into for-linus
Eric writes:
Please pull this bcache branch based on v4.8-rc2. These fix one
deadlock, one use blkdev_put() use counter, and one dmesg output with a
better pr_err() description.
Linus Torvalds [Fri, 19 Aug 2016 19:47:01 +0000 (12:47 -0700)]
Make the hardened user-copy code depend on having a hardened allocator
The kernel test robot reported a usercopy failure in the new hardened
sanity checks, due to a page-crossing copy of the FPU state into the
task structure.
This happened because the kernel test robot was testing with SLOB, which
doesn't actually do the required book-keeping for slab allocations, and
as a result the hardening code didn't realize that the task struct
allocation was one single allocation - and the sanity checks fail.
Since SLOB doesn't even claim to support hardening (and you really
shouldn't use it), the straightforward solution is to just make the
usercopy hardening code depend on the allocator supporting it.
Linus Torvalds [Fri, 19 Aug 2016 19:10:06 +0000 (12:10 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has some pretty standard driver bugfixes and one minor cleanup"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: meson: Use complete() instead of complete_all()
i2c: brcmstb: Use complete() instead of complete_all()
i2c: bcm-kona: Use complete() instead of complete_all()
i2c: bcm-iproc: Use complete() instead of complete_all()
i2c: at91: fix support of the "alternative command" feature
i2c: ocores: add missed clk_disable_unprepare() on failure paths
i2c: cros-ec-tunnel: Fix usage of cros_ec_cmd_xfer()
i2c: mux: demux-pinctrl: properly roll back when adding adapter fails
Vineet Gupta [Wed, 17 Aug 2016 01:27:07 +0000 (18:27 -0700)]
ARC: mm: fix build breakage with STRICT_MM_TYPECHECKS
| CC mm/memory.o
| In file included from ../mm/memory.c:53:0:
| ../include/linux/pfn_t.h: In function ‘pfn_t_pte’:
| ../include/linux/pfn_t.h:78:2: error: conversion to non-scalar type requested
| return pfn_pte(pfn_t_to_pfn(pfn), pgprot);
With STRICT_MM_TYPECHECKS pte_t is a struct and the offending code
forces a cast which ends up shifting a struct and hence the gcc warning.
Note that in recent past some of the arches (aarch64, s390) made
STRICT_MM_TYPECHECKS default, but we don't for ARC as this leads to slightly
worse generated code, given ARC ABI definition of returning structs
(which pte_t would become)
Quoting from ARC ABI...
"Results of type struct are returned in a caller-supplied temporary
variable whose address is passed in r0.
For such functions, the arguments are shifted so that they are
passed in r1 and up."
So
- struct to be returned would be allocated on stack requiring extra
code at call sites
- callee updates stack memory to facilitate the return (vs. simple
MOV into return reg r0)
Hence STRICT_MM_TYPECHECKS is not enabled by default for ARC
Vineet Gupta [Wed, 10 Aug 2016 21:10:57 +0000 (14:10 -0700)]
ARC: Support syscall ABI v4
The syscall ABI includes the gcc functional calling ABI since a syscall
implies userland caller and kernel callee.
The current gcc ABI (v3) for ARCv2 ISA required 64-bit data be passed in
even-odd register pairs, (potentially punching reg holes when passing such
values as args). This was partly driven by the fact that the double-word
LDD/STD instructions in ARCv2 expect the register alignment and thus gcc
forcing this avoids extra MOV at the cost of a few unused register (which we
have plenty anyways).
This however was rejected as part of upstreaming gcc port to HS. So the new
ABI v4 doesn't enforce the even-odd reg restriction.
Do note that for ARCompact ISA builds v3 and v4 are practically the same in
terms of gcc code generation.
In terms of change management, we infer the new ABI if gcc 6.x onwards
is used for building the kernel.
This also needs a stable backport to enable older kernels to work with
new tools/user-space
Liav Rehana [Tue, 16 Aug 2016 07:55:35 +0000 (10:55 +0300)]
ARC: use correct offset in pt_regs for saving/restoring user mode r25
User mode callee regs are explicitly collected before signal delivery or
breakpoint trap. r25 is special for kernel as it serves as task pointer,
so user mode value is clobbered very early. It is saved in pt_regs where
generally only scratch (aka caller saved) regs are saved.
The code to access the corresponding pt_regs location had a subtle bug as
it was using load/store with scaling of offset, whereas the offset was already
byte wise correct. So fix this by replacing LD.AS with a standard LD
Dmitry Torokhov [Wed, 17 Aug 2016 00:38:54 +0000 (17:38 -0700)]
Input: i8042 - set up shared ps2_cmd_mutex for AUX ports
The commit 4097461897df ("Input: i8042 - break load dependency ...")
correctly set up ps2_cmd_mutex pointer for the KBD port but forgot to do
the same for AUX port(s), which results in communication on KBD and AUX
ports to clash with each other.
Jens Axboe [Fri, 19 Aug 2016 16:51:15 +0000 (10:51 -0600)]
Merge branch 'stable/for-jens-4.8-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
Konrad writes:
Please git pull the following three fixes in to your 'for-linus' branch.
It is against 'for-linus' instead of 'for-4.8/drivers' because we had
some code in xen-blkfront go through the Xen tree (with your Ack). The
reason was that you 'for-4.8/drivers' was based on 4.7-rc2, and the
fixes needed to be against newer tag.
This branch fixes as we are exercising the multiqueue components more
aggressively.
Linus Torvalds [Fri, 19 Aug 2016 16:32:48 +0000 (09:32 -0700)]
Merge tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix for DM round robin multipath path selector to disable
preemption before using this_cpu_ptr()
- a slight increase in DM crypt's mempool reserves to make swap ontop
of DM crypt more performant
- a few DM raid fixes to issues found while testing changes that were
merged in v4.8-rc1
* tag 'dm-4.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm raid: support raid0 with missing metadata devices
dm raid: enhance attempt_restore_of_faulty_devices() to support more devices
dm raid: fix restoring of failed devices regression
dm raid: fix frozen recovery regression
dm crypt: increase mempool reserve to better support swapping
dm round robin: do not use this_cpu_ptr() without having preemption disabled
Bob Liu [Fri, 1 Jul 2016 21:43:39 +0000 (17:43 -0400)]
xen-blkfront: introduce blkif_set_queue_limits()
blk_mq_update_nr_hw_queues() reset all queue limits to default which it's
not as xen-blkfront expected, introducing blkif_set_queue_limits() to reset
limits with initial correct values.
Linus Torvalds [Fri, 19 Aug 2016 16:22:50 +0000 (09:22 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fairly small fixes. The ipr, mpt3sas and ses ones all trigger
oopses. The megaraid one fixes an attach failure on io mapped only
cards, the fcoe one is an obvious problem in the error path and the
aacraid one is a theoretical security issue (ability to trick the
kernel into a buffer overrun)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ses: Fix racy cleanup of /sys in remove_dev()
mpt3sas: Fix resume on WarpDrive flash cards
ipr: Fix sync scsi scan
megaraid_sas: Fix probing cards without io port
aacraid: Check size values after double-fetch from user
fcoe: Use kfree_skb() instead of kfree()
Linus Torvalds [Fri, 19 Aug 2016 16:21:24 +0000 (09:21 -0700)]
Merge tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for reported issues for your tree.
The normal amount of gadget fixes, xhci fixes, new device ids, and a
few other minor things. All of them have been in linux-next for a
while, the full details are in the shortlog below"
* tag 'usb-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (43 commits)
xhci: don't dereference a xhci member after removing xhci
usb: xhci: Fix panic if disconnect
xhci: really enqueue zero length TRBs.
xhci: always handle "Command Ring Stopped" events
cdc-acm: fix wrong pipe type on rx interrupt xfers
usb: misc: usbtest: add fix for driver hang
usb: dwc3: gadget: stop processing on HWO set
usb: dwc3: don't set last bit for ISOC endpoints
usb: gadget: rndis: free response queue during REMOTE_NDIS_RESET_MSG
usb: udc: core: fix error handling
usb: gadget: fsl_qe_udc: off by one in setup_received_handle()
usb/gadget: fix gadgetfs aio support.
usb: gadget: composite: Fix return value in case of error
usb: gadget: uvc: Fix return value in case of error
usb: gadget: fix check in sync read from ep in gadgetfs
usb: misc: usbtest: usbtest_do_ioctl may return positive integer
usb: dwc3: fix missing platform_set_drvdata() in dwc3_of_simple_probe()
usb: phy: omap-otg: Fix missing platform_set_drvdata() in omap_otg_probe()
usb: gadget: configfs: add mutex lock before unregister gadget
usb: gadget: u_ether: fix dereference after null check coverify warning
...
Linus Torvalds [Fri, 19 Aug 2016 16:06:41 +0000 (09:06 -0700)]
Merge tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs and iomap fixes from Dave Chinner:
"Changes in this update:
Regression fixes for XFS changes introduce in 4.8-rc1:
- buffer IO accounting assert failure
- ENOSPC block accounting reservation issue
- DAX IO path page cache invalidation fix
- rmapbt on-disk block count in agf
- correct classification of rmap block type when updating AGFL.
- iomap support for attribute fork mapping
Regression fixes for iomap infrastructure in 4.8-rc1:
- fiemap: honor FIEMAP_FLAG_SYNC
- fiemap: implement FIEMAP_FLAG_XATTR support to fix XFS regression
- make mark_page_accessed and pagefault_disable usage consistent with
other IO paths"
* tag 'xfs-iomap-for-linus-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: remove OWN_AG rmap when allocating a block from the AGFL
xfs: (re-)implement FIEMAP_FLAG_XATTR
xfs: simplify xfs_file_iomap_begin
iomap: mark ->iomap_end as optional
iomap: prepare iomap_fiemap for attribute mappings
iomap: fiemap should honor the FIEMAP_FLAG_SYNC flag
iomap: remove superflous pagefault_disable from iomap_write_actor
iomap: remove superflous mark_page_accessed from iomap_write_actor
xfs: store rmapbt block count in the AGF
xfs: don't invalidate whole file on DAX read/write
xfs: fix bogus space reservation in xfs_iomap_write_allocate
xfs: don't assert fail on non-async buffers on ioacct decrement
Linus Torvalds [Fri, 19 Aug 2016 15:52:17 +0000 (08:52 -0700)]
Merge tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix a bug in it87 driver and URLs in ftsteutates driver"
* tag 'hwmon-for-linus-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ftsteutates) Correct ftp urls in driver documentation
hwmon: (it87) Features mask must be 32 bit wide
James Hogan [Fri, 19 Aug 2016 13:30:29 +0000 (14:30 +0100)]
MIPS: KVM: Check for pfn noslot case
When mapping a page into the guest we error check using is_error_pfn(),
however this doesn't detect a value of KVM_PFN_NOSLOT, indicating an
error HVA for the page. This can only happen on MIPS right now due to
unusual memslot management (e.g. being moved / removed / resized), or
with an Enhanced Virtual Memory (EVA) configuration where the default
KVM_HVA_ERR_* and kvm_is_error_hva() definitions are unsuitable (fixed
in a later patch). This case will be treated as a pfn of zero, mapping
the first page of physical memory into the guest.
It would appear the MIPS KVM port wasn't updated prior to being merged
(in v3.10) to take commit 81c52c56e2b4 ("KVM: do not treat noslot pfn as
a error pfn") into account (merged v3.8), which converted a bunch of
is_error_pfn() calls to is_error_noslot_pfn(). Switch to using
is_error_noslot_pfn() instead to catch this case properly.
The dmic-codec was registered within the platform_driver's probe function,
which can cause deferred probe to run in loops as reported and analyzed by
Russell King.
Use module_init/exit in the driver and handle the dmic-codec device
registration and removal at that level instead of the platform_driver
probe/remove.
Corentin LABBE [Tue, 16 Aug 2016 08:51:38 +0000 (10:51 +0200)]
thermal: imx: fix a possible NULL dereference
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 472:
data->socdata = of_id->data;
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Brendan Jackman [Wed, 17 Aug 2016 15:14:59 +0000 (16:14 +0100)]
thermal: cpu_cooling: Fix NULL dereference in cpufreq_state2power
Currently all CPU cooling devices share a
`struct thermal_cooling_device_ops` instance. The thermal core uses the
presence of functions in this struct to determine if a cooling device
has a power model (see cdev_is_power_actor). cpu_cooling.c adds the
power model functions to the shared struct when a device is registered
with a power model.
Therefore, if a CPU cooling device is registered using
[of_]cpufreq_power_cooling_register, _all_ devices will be determined to
have a power model, including any registered with
[of_]cpufreq_cooling_register. This can result in cpufreq_state2power
being called on a device where dyn_power_table is NULL.
With this commit, instead of having a shared thermal_cooling_device_ops
which is mutated, we have two versions: one with the power functions and
one without.
Linus Walleij [Tue, 16 Aug 2016 10:07:31 +0000 (12:07 +0200)]
gpio: make any OF dependent driver depend on OF_GPIO
The drivers that depend on OF but not OF_GPIO are wreaking havoc
with the autobuilders for archs that have all requirements for
OF but not for OF_GPIO, particularly the UM (Usermode) arch does
not have iomem (NO_IOMEM) which result in configuring GPIOLIB but
without OF_GPIO which is wrong if the driver is using the .of_node
of the gpiochip, which only appears with OF_GPIO.
After a brief look at the drivers just depending on OF it seems
most if not all of them actually require stuff from gpiolib-of so
the dependency is wrong in the first place.
This simply patches the Kconfig so that all GPIO drivers using OF
depend on OF_GPIO rather than just OF.
Linus Walleij [Tue, 16 Aug 2016 07:58:25 +0000 (09:58 +0200)]
gpio: Fix OF build problem on UM
The UserMode (UM) Linux build was failing in gpiolib-of as it requires
ioremap()/iounmap() to exist, which is absent from UM. The non-existence
of IO memory is negatively defined as CONFIG_NO_IOMEM which means we
need to depend on HAS_IOMEM.
Mark Brown [Thu, 18 Aug 2016 18:32:59 +0000 (19:32 +0100)]
ASoC: core: Clean up DAPM before the card debugfs
Both the card and DAPM cleanups recursively delete their debugfs
directories. Since the DAPM debugfs subdirectory for the card is
located within the card debugfs this means we end up trying to double
free the DAPM subdirectory. Reorder the cleanup to free the card
debugfs after we've cleaned up DAPM and it has deleted its own
subdirectory.
Will Deacon [Tue, 16 Aug 2016 13:29:16 +0000 (14:29 +0100)]
iommu/arm-smmu: Don't BUG() if we find aborting STEs with disable_bypass
The disable_bypass cmdline option changes the SMMUv3 driver to put down
faulting stream table entries by default, as opposed to bypassing
transactions from unconfigured devices.
In this mode of operation, it is entirely expected to see aborting
entries in the stream table if and when we come to installing a valid
translation, so don't trigger a BUG() as a result of misdiagnosing these
entries as stream table corruption.
Will Deacon [Fri, 5 Aug 2016 18:49:45 +0000 (19:49 +0100)]
iommu/arm-smmu: Disable stalling faults for all endpoints
Enabling stalling faults can result in hardware deadlock on poorly
designed systems, particularly those with a PCI root complex upstream of
the SMMU.
Although it's not really Linux's job to save hardware integrators from
their own misfortune, it *is* our job to stop userspace (e.g. VFIO
clients) from hosing the system for everybody else, even if they might
already be required to have elevated privileges.
Given that the fault handling code currently executes entirely in IRQ
context, there is nothing that can sensibly be done to recover from
things like page faults anyway, so let's rip this code out for now and
avoid the potential for deadlock.
Cc: <[email protected]> Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices") Reported-by: Matt Evans <[email protected]> Signed-off-by: Will Deacon <[email protected]>
David Daney [Thu, 18 Aug 2016 22:41:58 +0000 (15:41 -0700)]
irqchip/gicv3-its: Disable the ITS before initializing it
When starting a kexec/kdump kernel, the GIC ITS will already have been
enabled. According to the ARM Generic Interrupt Controller
Architecture Specification (GIC architecture Version 3.0 and version
4.0), writing to GITS_BASER<n> or GITS_CBASER is "UNPREDICTABLE" when
the ITS is enabled. On Cavium Thunder systems, this prevents the ITS
from being initializing in the kexec/kdump kernel, resulting in
failure to register/enable interrupts for all devices.
The fix is to disable the ITS if it is not already in the disabled
state. This allows the ITS to be properly initialized and then
re-enabled in the kexec/kdump kernel.
Will Deacon [Fri, 29 Jul 2016 10:15:37 +0000 (11:15 +0100)]
iommu/arm-smmu: Fix CMDQ error handling
In the unlikely event of a global command queue error, the ARM SMMUv3
driver attempts to convert the problematic command into a CMD_SYNC and
resume the command queue. Unfortunately, this code is pretty badly
broken:
1. It uses the index into the error string table as the CMDQ index,
so we probably read the wrong entry out of the queue
2. The arguments to queue_write are the wrong way round, so we end up
writing from the queue onto the stack.
These happily cancel out, so the kernel is likely to stay alive, but
the command queue will probably fault again when we resume.
This patch fixes the error handling code to use the correct queue index
and write back the CMD_SYNC to the faulting entry.
Cc: <[email protected]> Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices") Reported-by: Diwakar Subraveti <[email protected]> Signed-off-by: Will Deacon <[email protected]>
Robin Murphy [Thu, 11 Aug 2016 16:44:05 +0000 (17:44 +0100)]
iommu/io-pgtable-arm-v7s: Fix attributes when splitting blocks
Due to the attribute bits being all over the place in the different
types of short-descriptor PTEs, when remapping an existing entry, e.g.
splitting a section into pages, we take the approach of decomposing
the PTE attributes back to the IOMMU API flags to start from scratch.
On inspection, though, the existing code seems to have got the read-only
bit backwards and ignored the XN bit. How embarrassing...
Fortunately the primary user so far, the Mediatek IOMMU, both never
splits blocks (because it only serves non-overlapping DMA API calls) and
also ignores permissions anyway, but let's put things right before any
future users trip up.
Eric Wheeler [Fri, 19 Aug 2016 03:15:26 +0000 (20:15 -0700)]
bcache: pr_err: more meaningful error message when nr_stripes is invalid
The original error was thought to be corruption, but was actually caused by:
make-bcache --data-offset N
where N was in bytes and should have been in sectors. While userspace
tools should be updated to check --data-offset beyond end of volume,
hopefully this will help others that might not have noticed the units.
The fifo code in upstream bcache can't use the last element in the buffer,
which was the cause of the bug: if you asked for a power of two size,
it'd give you a fifo that could hold one less than what you asked for
rather than allocating a buffer twice as big.
Eric Wheeler [Fri, 17 Jun 2016 22:01:54 +0000 (15:01 -0700)]
bcache: register_bcache(): call blkdev_put() when cache_alloc() fails
register_cache() is supposed to return an error string on error so that
register_bcache() will will blkdev_put and cleanup other user counters,
but it does not set 'char *err' when cache_alloc() fails (eg, due to
memory pressure) and thus register_bcache() performs no cleanup.
register_bcache() <----------\ <- no jump to err_close, no blkdev_put()
| |
+->register_cache() | <- fails to set char *err
| |
+->cache_alloc() ---/ <- returns error
This patch sets `char *err` for this failure case so that register_cache()
will cause register_bcache() to correctly jump to err_close and do
cleanup. This was tested under OOM conditions that triggered the bug.
Linus Torvalds [Fri, 19 Aug 2016 02:38:18 +0000 (19:38 -0700)]
Merge tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Daniel pointed out I'd missed some i915 fixes, and I also found a
single etnaviv fix I missed.
So here they are"
* tag 'drm-fixes-for-4.8-rc3-2' of git://people.freedesktop.org/~airlied/linux:
drm/etnaviv: take GPU lock later in the submit process
drm/i915: Fix modeset handling during gpu reset, v5.
drm/i915: fix aliasing_ppgtt leak
drm/i915: fix WaInsertDummyPushConstPs
drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
drm/i915: Acquire audio powerwell for HD-Audio registers
drm/i915: Add missing rpm wakelock to GGTT pread
drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
drm/i915: Program iboost settings for HDMI/DVI on SKL
drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
drm/i915: Handle ENOSPC after failing to insert a mappable node
drm/i915: Flush GT idle status upon reset
Linus Torvalds [Fri, 19 Aug 2016 02:31:08 +0000 (19:31 -0700)]
Merge tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- a couple of DT node ref counting fixes
- fix __unflatten_device_tree for PPC PCI hotplug case
- rework marking irq controllers as OF_POPULATED in cases where real
driver is used.
- disable of_platform_default_populate_init on PPC. The change in
initcall order causes problems which need to be sorted out later.
* tag 'devicetree-fixes-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: fix reference counting in of_graph_get_endpoint_by_regs
of/platform: disable the of_platform_default_populate_init() for all the ppc boards
ARM: imx6: mark GPC node as not populated after irq init to probe pm domain driver
of/irq: Mark interrupt controllers as populated before initialisation
drivers/of: Validate device node in __unflatten_device_tree()
of: Delete an unnecessary check before the function call "of_node_put"
When testing with generic/032 of xfstest suit, failure message will be
reported as below:
generic/032 8s ... [failed, exit status 1] - output mismatch (see results/generic/032.out.bad)
--- tests/generic/032.out 2015-01-11 16:52:27.643681072 +0800
+++ results/generic/032.out.bad 2016-08-06 13:44:43.861330500 +0800
@@ -1,5 +1,5 @@
QA output created by 032
-100 iterations
-0000000 cdcd cdcd cdcd cdcd cdcd cdcd cdcd cdcd
-*
-0100000
+1: [768..775]: unwritten
+Unwritten extents found!
...
(Run 'diff -u tests/generic/032.out results/generic/032.out.bad' to see the entire diff)
Ran: generic/032
Failures: generic/032
Failed 1 of 1 tests
In write_end(), we should update i_size of inode before unlock page,
otherwise, we will lose newly updated data in following race condition.
Thread A Thread B
- write_end
- unlock page
- writepages
- lock_page
- writepage
if page is out-of-range of file size,
we will skip writting the page.
- update i_size
Linus Torvalds [Fri, 19 Aug 2016 01:54:40 +0000 (18:54 -0700)]
Merge tag '4.8-doc-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Three small fixes for Sphinx-formatted documentation generation"
* tag '4.8-doc-fixes' of git://git.lwn.net/linux:
doc-rst: customize RTD theme, drop padding of inline literal
docs: kernel-documentation: remove some highlight directives
docs: Set the Sphinx default highlight language to "guess"
Dave Airlie [Thu, 18 Aug 2016 22:51:13 +0000 (08:51 +1000)]
Merge tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Collection of i915 fixes.
* tag 'drm-intel-fixes-2016-08-15' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix modeset handling during gpu reset, v5.
drm/i915: fix aliasing_ppgtt leak
drm/i915: fix WaInsertDummyPushConstPs
drm/i915: Fix iboost setting for SKL Y/U DP DDI buffer translation entry 2
drm/i915/gen9: Give one extra block per line for SKL plane WM calculations
drm/i915: Acquire audio powerwell for HD-Audio registers
drm/i915: Add missing rpm wakelock to GGTT pread
drm/i915/fbc: FBC causes display flicker when VT-d is enabled on Skylake
drm/i915: Clean up the extra RPM ref on CHV with i915.enable_rc6=0
drm/i915: Program iboost settings for HDMI/DVI on SKL
drm/i915: Fix iboost setting for DDI with 4 lanes on SKL
drm/i915: Handle ENOSPC after failing to insert a mappable node
drm/i915: Flush GT idle status upon reset
Linus Torvalds [Thu, 18 Aug 2016 22:09:41 +0000 (15:09 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"An initrd microcode loading fix, and an SMP bootup topology setup fix
to resolve crashes on SGI/UV systems if the BIOS is configured in a
certain way"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Fix __max_logical_packages value setup
x86/microcode/AMD: Fix initrd loading with CONFIG_RANDOMIZE_MEMORY=y
Linus Torvalds [Thu, 18 Aug 2016 22:08:31 +0000 (15:08 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Three clocksource driver fixes"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/mips-gic-timer: Make gic_clocksource_of_init() return int
clocksource/drivers/kona: Fix get_counter() error handling
clocksource/drivers/time-armada-370-xp: Fix the clock reference
Linus Torvalds [Thu, 18 Aug 2016 22:04:53 +0000 (15:04 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also start/stop filter related fixes, a perf
event read() fix, a fix uncovered by fuzzing, and an uprobes leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Check return value of the perf_event_read() IPI
perf/core: Enable mapping of the stop filters
perf/core: Update filters only on executable mmap
perf/core: Fix file name handling for start/stop filters
perf/core: Fix event_function_local()
uprobes: Fix the memcg accounting
perf intel-pt: Fix occasional decoding errors when tracing system-wide
tools: Sync kvm related header files for arm64 and s390
perf probe: Release resources on error when handling exit paths
perf probe: Check for dup and fdopen failures
perf symbols: Fix annotation of objects with debuginfo files
perf script: Don't disable use_callchain if input is pipe
perf script: Show proper message when failed list scripts
perf jitdump: Add the right header to get the major()/minor() definitions
perf ppc64le: Fix build failure when libelf is not present
perf tools mem: Fix -t store option for record command
perf intel-pt: Fix ip compression
Ingo Molnar [Thu, 18 Aug 2016 20:50:36 +0000 (22:50 +0200)]
Merge tag 'perf-urgent-for-mingo-20160818' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Do not access outside hw cache name arrays (Arnaldo Carvalho de Melo)
- Use addr_location::addr instead of ip for entries when unwinding using
DWARF CFI, fixing the "srcline" information for userspace application
callchains (Milian Wolff)
- Reinstate strlcpy() header guard with __UCLIBC__, fixing the build
with uclibc, detected when building for the ARC architecture (Vineet Gupta)
perf evsel: Do not access outside hw cache name arrays
We have to check if the values are >= *_MAX, not just >, fix it.
From the bugzilla report:
''In file /tools/perf/util/evsel.c function __perf_evsel__hw_cache_name
it appears that there is a bug that reads beyond the end of the buffer.
The statement "if (type > PERF_COUNT_HW_CACHE_MAX)" allows type to be
equal to the maximum value. Later, when statement "if
(!perf_evsel__is_cache_op_valid(type, op))" is executed, the function
can access array perf_evsel__hw_cache_stat[type] beyond the end of the
buffer.
It appears to me that the statement "if (type > PERF_COUNT_HW_CACHE_MAX)"
should be "if (type >= PERF_COUNT_HW_CACHE_MAX)"
Bug found with Coverity and manual code review. No attempts were made to
execute the code with a maximum type value.''
Committer note:
Testing it:
$ perf record -e $(echo $(perf list cache | cut -d \[ -f1) | sed 's/ /,/g') usleep 1
[ perf record: Woken up 16 times to write data ]
[ perf record: Captured and wrote 0.023 MB perf.data (34 samples) ]
$ perf evlist
L1-dcache-load-misses
L1-dcache-loads
L1-dcache-stores
L1-icache-load-misses
LLC-load-misses
LLC-loads
LLC-store-misses
LLC-stores
branch-load-misses
branch-loads
dTLB-load-misses
dTLB-loads
dTLB-store-misses
dTLB-stores
iTLB-load-misses
iTLB-loads
node-load-misses
node-loads
node-store-misses
node-stores
$ perf list cache
Vineet Gupta [Thu, 18 Aug 2016 16:28:23 +0000 (09:28 -0700)]
tools lib: Reinstate strlcpy() header guard with __UCLIBC__
perf tools build in recent kernels spews splat when cross compiling with uClibc:
| CC util/alias.o
| In file included from tools/perf/util/../ui/../util/cache.h:8:0,
| from tools/perf/util/../ui/helpline.h:7,
| from tools/perf/util/debug.h:8,
| from arch/../util/cpumap.h:9,
| from arch/../util/env.h:5,
| from arch/common.h:4,
| from arch/common.c:3:
| tools/include/linux/string.h:12:15: warning: redundant redeclaration of ‘strlcpy’ [-Wredundant-decls]
| extern size_t strlcpy(char *dest, const char *src, size_t size);
^
This is after commit 61a6445e463a31 ("tools lib: Guard the strlcpy() header with
__GLIBC__").
The problem is uClibc also defines __GLIBC__ for exported headers for
applications. So add that specific check to not trip for uClibc.
Linus Torvalds [Thu, 18 Aug 2016 18:17:13 +0000 (11:17 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Avoid a literal load with the MMU off on the CPU resume path
(potential inconsistency between cache and RAM)
- Build error with CONFIG_ACPI=n fixed
- Compiler warning in the arch/arm64/mm/dump.c code fixed
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix shift warning in arch/arm64/mm/dump.c
arm64: kernel: avoid literal load of virtual address with MMU off
arm64: Fix NUMA build error when !CONFIG_ACPI
Linus Torvalds [Thu, 18 Aug 2016 18:09:43 +0000 (11:09 -0700)]
Merge tag 'pm-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"More hibernation-related material: one fix for a recent regression in
the core, one small cleanup of the x86-64 resume code and a
documentation update.
Specifics:
- Fix a hibernate core regression resulting from uncovering a latent
bug in its implementation of memory bitmaps by a recent commit
(James Morse).
- Use __pa() to compute a physical address in the x86-64 code
finalizing resume from hibernation (Rafael Wysocki).
- Update power management documentation related to system sleep
states to remove outdated information from it and to add a
description of a recently introduced hibernation debug feature to
it (Rafael Wysocki)"
* tag 'pm-4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / hibernate: Fix rtree_next_node() to avoid walking off list ends
x86/power/64: Use __pa() for physical address computation
PM / sleep: Update some system sleep documentation
Linus Torvalds [Thu, 18 Aug 2016 17:58:50 +0000 (10:58 -0700)]
Merge tag 'drm-fixes-for-4.8-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Pretty quiet so far:
- a few amdgpu/radeon fixup for pcie pm changes
- a couple of amdgpu fixes
- some build fixes
- printk fix"
* tag 'drm-fixes-for-4.8-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: Change GART offset to 64-bit
drm/mediatek: add ARM_SMCCC dependency
drm/mediatek: add CONFIG_OF dependency
drm/mediatek: add COMMON_CLK dependency
drm/amdgpu: Fix memory trashing if UVD ring test fails
drm/amdgpu: fix vm init error path
drm/amdkfd: print doorbell offset as a hex value
Revert "drm/radeon: work around lack of upstream ACPI support for D3cold"
Revert "drm/amdgpu: work around lack of upstream ACPI support for D3cold"
The patches for twl6040 MFD and clk missed the merge window and
causing the McPDM driver to never probe since it is put back to
the deferred list because the missing drivers.
Johannes Berg [Thu, 11 Aug 2016 09:50:22 +0000 (11:50 +0200)]
locking/barriers: Suppress sparse warnings in lockless_dereference()
After Peter's commit:
331b6d8c7afc ("locking/barriers: Validate lockless_dereference() is used on a pointer type")
... we get a lot of sparse warnings (one for every rcu_dereference, and more)
since the expression here is assigning to the wrong address space.
Instead of validating that 'p' is a pointer this way, instead make
it fail compilation when it's not by using sizeof(*(p)). This will
not cause any sparse warnings (tested, likely since the address
space is irrelevant for sizeof), and will fail compilation when
'p' isn't a pointer type.
Johannes Berg [Thu, 11 Aug 2016 09:50:21 +0000 (11:50 +0200)]
Revert "drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference"
This reverts commit:
fa7d81bb3c269 ("drm/fb-helper: Reduce READ_ONCE(master) to lockless_dereference")
As Peter explained:
[...] lockless_dereference() is _stronger_ than READ_ONCE(), not weaker.
[...]
Also, clue is in the name: 'dereference', you don't actually dereference
the pointer here, only load it.
My next patch breaks the compile without this revert, because it assumes
you want to deference and thus also need the struct type visible (which
it isn't here), so revert it.
PCI: Call pci_intx() when using legacy interrupts in pci_alloc_irq_vectors()
ahci currently insists on an explicit call to pci_intx() before falling
back from MSI or MSI-X to legacy IRQs. As pci_intx() is a no-op if the
command register already contains the right value it seems safe and useful
to add this call to pci_alloc_irq_vectors() so that ahci can just use
pci_alloc_irq_vectors().
Paolo Bonzini [Thu, 18 Aug 2016 10:19:19 +0000 (12:19 +0200)]
Merge tag 'kvm-arm-for-v4.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Fixes for v4.8-rc3
This tag contains the following fixes on top of v4.8-rc1:
- ITS init issues
- ITS error handling issues
- ITS IRQ leakage fix
- Plug a couple of ITS race conditions
- An erratum workaround for timers
- Some removal of misleading use of errors and comments
- A fix for GICv3 on 32-bit guests
Radim Krčmář [Mon, 8 Aug 2016 18:16:23 +0000 (20:16 +0200)]
KVM: nVMX: postpone VMCS changes on MSR_IA32_APICBASE write
If vmcs12 does not intercept APIC_BASE writes, then KVM will handle the
write with vmcs02 as the current VMCS.
This will incorrectly apply modifications intended for vmcs01 to vmcs02
and L2 can use it to gain access to L0's x2APIC registers by disabling
virtualized x2APIC while using msr bitmap that assumes enabled.
Postpone execution of vmx_set_virtual_x2apic_mode until vmcs01 is the
current VMCS. An alternative solution would temporarily make vmcs01 the
current VMCS, but it requires more care.
Radim Krčmář [Mon, 8 Aug 2016 18:16:22 +0000 (20:16 +0200)]
KVM: nVMX: fix msr bitmaps to prevent L2 from accessing L0 x2APIC
msr bitmap can be used to avoid a VM exit (interception) on guest MSR
accesses. In some configurations of VMX controls, the guest can even
directly access host's x2APIC MSRs. See SDM 29.5 VIRTUALIZING MSR-BASED
APIC ACCESSES.
L2 could read all L0's x2APIC MSRs and write TPR, EOI, and SELF_IPI.
To do so, L1 would first trick KVM to disable all possible interceptions
by enabling APICv features and then would turn those features off;
nested_vmx_merge_msr_bitmap() only disabled interceptions, so VMX would
not intercept previously enabled MSRs even though they were not safe
with the new configuration.
Correctly re-enabling interceptions is not enough as a second bug would
still allow L1+L2 to access host's MSRs: msr bitmap was shared for all
VMCSs, so L1 could trigger a race to get the desired combination of msr
bitmap and VMX controls.
This fix allocates a msr bitmap for every L1 VCPU, allows only safe
x2APIC MSRs from L1's msr bitmap, and disables msr bitmaps if they would
have to intercept everything anyway.
On an i5 laptop, 4 pCPUs, 4vCPUs for one full dynticks guest, there are four
CPU hog processes(for loop) running in the guest, I hot-unplug the pCPUs
on host one by one until there is only one left, then observe CPU utilization
via 'top' in the guest, it shows:
100% st for cpu0(housekeeping)
75% st for other CPUs (nohz full mode)
However, w/o this commit it shows the correct 75% for all four CPUs.
When a guest is interrupted for a longer amount of time, missed clock ticks
are not redelivered later. Because of that, we should not limit the amount
of steal time accounted to the amount of time that the calling functions
think have passed.
However, the interval returned by account_other_time() is NOT rounded down
to the nearest jiffy, while the base interval in get_vtime_delta() it is
subtracted from is, so the max cputime limit is required to avoid underflow.
This patch fixes the regression by limiting the account_other_time() from
get_vtime_delta() to avoid underflow, and lets the other three call sites
(in account_other_time() and steal_account_process_time()) account however
much steal time the host told us elapsed.
perf/core: Check return value of the perf_event_read() IPI
The call to smp_call_function_single in perf_event_read() may fail if
an invalid or not online CPU index is passed. Warn user if such bug is
present and return error.
At this time the perf_addr_filter_needs_mmap() function will _not_
return true on a user space 'stop' filter. But stop filters need
exactly the same kind of mapping that range and start filters get.
Function perf_event_mmap() is called by the MM subsystem each time
part of a binary is loaded in memory. There can be several mapping
for a binary, many times unrelated to the code section.
Each time a section of a binary is mapped address filters are
updated, event when the map doesn't pertain to the code section.
The end result is that filters are configured based on the last map
event that was received rather than the last mapping of the code
segment.
For example if we have an executable 'main' that calls library
'libcstest.so.1.0', and that we want to collect traces on code
that is in that library. The perf cmd line for this scenario
would be:
perf record -e cs_etm// --filter 'filter 0x72c/0x40@/opt/lib/libcstest.so.1.0' --per-thread ./main
Before 'main()' can execute 'libcstest.so.1.0' has to be loaded in
memory. Once that has been done perf_event_mmap() has been called
4 times, with the last map starting at address 0x7fa25ce000 and
the address filter configured to start filtering when the
IP has passed over address 0x0x7fa25ce72c (0x7fa25ce000 + 0x72c).
But that is wrong since the code segment for library 'libcstest.so.1.0'
as been mapped at 0x7fa25bd000, resulting in traces not being
collected.
This patch corrects the situation by requesting that address
filters be updated only if the mapped event is for a code
segment.
perf/core: Fix file name handling for start/stop filters
Binary file names have to be supplied for both range and start/stop
filters but the current code only processes the filename if an
address range filter is specified. This code adds processing of
the filename for start/stop filters.
The reason for the panic is wrong value of __max_logical_packages,
which lets logical_package_map uninitialized and the uncore code
relying on this map being properly initialized (maybe we should
add some safety checks there as well).
The __max_logical_packages is computed as:
DIV_ROUND_UP(total_cpus, ncpus);
- ncpus being number of cores
With above BIOS setup we get total_cpus == 16 which set
__max_logical_packages to 2 (ncpus is 12).
Once topology_update_package_map processes CPU with logical
pkg over 2 we display above messages and fail to initialize
the physical_to_logical_pkg map, which makes the uncore code
crash.
The fix is to remove logical_package_map bitmap completely
and keep and update the logical_packages number instead.
After we enumerate all the present CPUs, we check if the
enumerated logical packages count is within its computed
maximum from BIOS data.
If it's not the case, we set this maximum to the new enumerated
value and freeze any new addition of logical packages.
The freeze is because lot of init code like uncore/rapl/cqm
depends on having maximum logical package value set to allocate
their data, so we can't change it later on.
Prarit Bhargava tested the patch and confirms that it solves
the problem:
Oleg Nesterov [Wed, 17 Aug 2016 15:36:29 +0000 (17:36 +0200)]
uprobes: Fix the memcg accounting
__replace_page() wronlgy calls mem_cgroup_cancel_charge() in "success" path,
it should only do this if page_check_address() fails.
This means that every enable/disable leads to unbalanced mem_cgroup_uncharge()
from put_page(old_page), it is trivial to underflow the page_counter->count
and trigger OOM.
* pm-sleep:
PM / hibernate: Fix rtree_next_node() to avoid walking off list ends
x86/power/64: Use __pa() for physical address computation
PM / sleep: Update some system sleep documentation
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
Roman Mashak [Sun, 14 Aug 2016 05:35:02 +0000 (22:35 -0700)]
net_sched: allow flushing tc police actions
The act_police uses its own code to walk the
action hashtable, which leads to that we could
not flush standalone tc police actions, so just
switch to tcf_generic_walker() like other actions.
WANG Cong [Sun, 14 Aug 2016 05:35:01 +0000 (22:35 -0700)]
net_sched: unify the init logic for act_police
Jamal reported a crash when we create a police action
with a specific index, this is because the init logic
is not correct, we should always create one for this
case. Just unify the logic with other tc actions.
WANG Cong [Sun, 14 Aug 2016 05:35:00 +0000 (22:35 -0700)]
net_sched: convert tcf_exts from list to pointer array
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
WANG Cong [Sun, 14 Aug 2016 05:34:57 +0000 (22:34 -0700)]
net_sched: remove an unnecessary list_del()
This list_del() for tc action is not needed actually,
because we only use this list to chain bulk operations,
therefore should not be carried for latter operations.
projects / linux.git / log