Avoid spurious link status logs that may ultimately be wrong; for example,
if the link is set to down with the cable plugged, then the cable is
unplugged and after this the link is set to up, the last new log that is
appearing is incorrectly telling that the link is up.
In order to avoid errors, show link status logs after link_reset
processing, and in order to avoid spurious as much as possible, only show
the link loss when some link status change is detected.
cc: [email protected] Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Signed-off-by: Jose Ignacio Tornos Martinez <[email protected]> Reviewed-by: Simon Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Sun, 23 Jun 2024 15:06:01 +0000 (11:06 -0400)]
Merge tag 'i2c-for-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The core gains placeholders for recently added functions when
CONFIG_I2C is not defined as well documentation fixes to start using
inclusive terminology.
The drivers get paths in DT bindings fixed as well as proper interrupt
handling for the ocores driver"
* tag 'i2c-for-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
docs: i2c: summary: be clearer with 'controller/target' and 'adapter/client' pairs
docs: i2c: summary: document 'local' and 'remote' targets
docs: i2c: summary: document use of inclusive language
docs: i2c: summary: update speed mode description
docs: i2c: summary: update I2C specification link
docs: i2c: summary: start sentences consistently.
i2c: Add nop fwnode operations
i2c: ocores: set IACK bit after core is enabled
dt-bindings: i2c: google,cros-ec-i2c-tunnel: correct path to i2c-controller schema
dt-bindings: i2c: atmel,at91sam: correct path to i2c-controller schema
Linus Torvalds [Sun, 23 Jun 2024 15:01:57 +0000 (11:01 -0400)]
Merge tag '6.10-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
"Five smb3 client fixes
- three nets/fiolios cifs fixes
- fix typo in module parameters description
- fix incorrect swap warning"
* tag '6.10-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Move the 'pid' from the subreq to the req
cifs: Only pick a channel once per read request
cifs: Defer read completion
cifs: fix typo in module parameter enable_gcm_256
cifs: drop the incorrect assertion in cifs_swap_rw()
Linus Torvalds [Sun, 23 Jun 2024 14:32:24 +0000 (10:32 -0400)]
Merge tag 'fixes-2024-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fix from Mike Rapoport:
"Fix fragility in checks for unset node ID.
Use numa_valid_node() function to verify that nid is a valid node
ID instead of inconsistent comparisons with either NUMA_NO_NODE or
MAX_NUMNODES"
* tag 'fixes-2024-06-23' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock: use numa_valid_node() helper to check for invalid node ID
Linus Torvalds [Sun, 23 Jun 2024 14:13:23 +0000 (07:13 -0700)]
Merge tag 'powerpc-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Prevent use-after-free in 64-bit KVM VFIO
- Add generated Power8 crypto asm to .gitignore
Thanks to Al Viro and Nathan Lynch.
* tag 'powerpc-6.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group()
powerpc/crypto: Add generated P8 asm to .gitignore
Jan Sokolowski [Fri, 21 Jun 2024 17:54:19 +0000 (10:54 -0700)]
ice: Rebuild TC queues on VSI queue reconfiguration
TC queues needs to be correctly updated when the number of queues on
a VSI is reconfigured, so netdev's queue and TC settings will be
dynamically adjusted and could accurately represent the underlying
hardware state after changes to the VSI queue counts.
Fixes: 0754d65bd4be ("ice: Add infrastructure for mqprio support via ndo_setup_tc") Reviewed-by: Wojciech Drewek <[email protected]> Signed-off-by: Jan Sokolowski <[email protected]> Signed-off-by: Karen Ostrowska <[email protected]> Tested-by: Pucha Himasekhar Reddy <[email protected]> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Frank Li [Fri, 21 Jun 2024 17:00:00 +0000 (13:00 -0400)]
dt-bindings: net: fman: remove ptp-timer from required list
IEEE1588(ptp) is optional feature for network. Remove it from required
list to fix below CHECK_DTBS warning.
arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dtb: ethernet@f0000: 'ptp-timer' is a required property
---
v7:
- use dev_crit_once instead of dev_crit_ratelimited
- add a comment to help users understand the consequences of half-duplex errors
v6: https://lore.kernel.org/netdev/20240614094642[email protected]/
- remove KSZ9897 phy_id workaround (was a configuration issue)
- use macros for checking link down in monitoring function
- check if VLAN is enabled before monitoring resources
v5: https://lore.kernel.org/all/20240604092304[email protected]/
- use macros for bitfields
- rewrap comments
- check ksz_pread* return values
- fix spelling mistakes
- remove KSZ9477 suspend/resume deletion patch
v4: https://lore.kernel.org/all/20240531142430[email protected]/
- Rebase on net/main
- Add Fixes: tags to the patches
- reverse x-mas tree order
- use pseudo phy_id instead of match_phy_device
v3: https://lore.kernel.org/all/20240530102436[email protected]/
====================
net: dsa: microchip: monitor potential faults in half-duplex mode
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477") Signed-off-by: Enguerrand de Ribaucourt <[email protected]> Reviewed-by: Andrew Lunn <[email protected]> Signed-off-by: David S. Miller <[email protected]>
net: dsa: microchip: use collision based back pressure mode
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Kory Maincent [Fri, 21 Jun 2024 13:00:59 +0000 (15:00 +0200)]
netlink: specs: Fix pse-set command attributes
Not all PSE attributes are used for the pse-set netlink command.
Select only the ones used by ethtool.
Fixes: f8586411e40e ("netlink: specs: Expand the pse netlink command with PoE interface") Signed-off-by: Kory Maincent <[email protected]> Reviewed-by: Donald Hunter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Wolfram Sang [Sun, 23 Jun 2024 00:13:27 +0000 (02:13 +0200)]
Merge tag 'i2c-host-fixes-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-current
This pull request fixes the paths of the dt-schema to their
complete locations for the ChromeOS EC tunnel driver and the
Atmel at91sam drivers.
Additionally, the OpenCores driver receives a fix for an issue
that dates back to version 2.6.18. Specifically, the interrupts
need to be acknowledged (clearing all pending interrupts) after
enabling the core.
Linus Torvalds [Sat, 22 Jun 2024 21:02:16 +0000 (14:02 -0700)]
Merge tag 'regulator-fix-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few driver specific fixes for incorrect device descriptions, plus a
fix for a missing symbol export which causes build failures for some
newly added drivers in other trees"
* tag 'regulator-fix-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: axp20x: AXP717: fix LDO supply rails and off-by-ones
regulator: bd71815: fix ramp values
regulator: core: Fix modpost error "regulator_get_regmap" undefined
regulator: tps6594-regulator: Fix the number of irqs for TPS65224 and TPS6594
Linus Torvalds [Sat, 22 Jun 2024 20:58:47 +0000 (13:58 -0700)]
Merge tag 'spi-fix-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A number of fixes that have built up for SPI, a bunch of driver
specific ones including an unfortunate revert of an optimisation for
the i.MX driver which was causing issues with some configurations,
plus a couple of core fixes for the rarely used octal mode and for a
bad interaction between multi-CS support and target mode"
* tag 'spi-fix-v6.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-imx: imx51: revert burst length calculation back to bits_per_word
spi: Fix SPI slave probe failure
spi: Fix OCTAL mode support
spi: stm32: qspi: Clamp stm32_qspi_get_mode() output to CCR_BUSWIDTH_4
spi: stm32: qspi: Fix dual flash mode sanity test in stm32_qspi_setup()
spi: cs42l43: Drop cs35l56 SPI speed down to 11MHz
spi: cs42l43: Correct SPI root clock speed
Linus Torvalds [Sat, 22 Jun 2024 20:55:56 +0000 (13:55 -0700)]
Merge tag 'nfsd-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Fix crashes triggered by administrative operations on the server
* tag 'nfsd-6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: grab nfsd_mutex in nfsd_nl_rpc_status_get_dumpit()
nfsd: fix oops when reading pool_stats before server is started
Linus Torvalds [Sat, 22 Jun 2024 16:02:39 +0000 (09:02 -0700)]
Merge tag 'bcachefs-2024-06-22' of https://evilpiepirate.org/git/bcachefs
Pull bcachefs fixes from Kent Overstreet:
"Lots of (mostly boring) fixes for syzbot bugs and rare(r) CI bugs.
The LRU_TIME_BITS fix was slightly more involved; we only have 48 bits
for the LRU position (we would prefer 64), so wraparound is possible
for the cached data LRUs on a filesystem that has done sufficient
(petabytes) reads; this is now handled.
One notable user reported bugfix, where we were forgetting to
correctly set the bucket data type, which should have been
BCH_DATA_need_gc_gens instead of BCH_DATA_free; this was causing us to
go emergency read-only on a filesystem that had seen heavy enough use
to see bucket gen wraparoud.
We're now starting to fix simple (safe) errors without requiring user
intervention - i.e. a small incremental step towards full self
healing.
This is currently limited to just certain allocation information
counters, and the error is still logged in the superblock; see that
patch for more information. ("bcachefs: Fix safe errors by default")"
* tag 'bcachefs-2024-06-22' of https://evilpiepirate.org/git/bcachefs: (22 commits)
bcachefs: Move the ei_flags setting to after initialization
bcachefs: Fix a UAF after write_super()
bcachefs: Use bch2_print_string_as_lines for long err
bcachefs: Fix I_NEW warning in race path in bch2_inode_insert()
bcachefs: Replace bare EEXIST with private error codes
bcachefs: Fix missing alloc_data_type_set()
closures: Change BUG_ON() to WARN_ON()
bcachefs: fix alignment of VMA for memory mapped files on THP
bcachefs: Fix safe errors by default
bcachefs: Fix bch2_trans_put()
bcachefs: set_worker_desc() for delete_dead_snapshots
bcachefs: Fix bch2_sb_downgrade_update()
bcachefs: Handle cached data LRU wraparound
bcachefs: Guard against overflowing LRU_TIME_BITS
bcachefs: delete_dead_snapshots() doesn't need to go RW
bcachefs: Fix early init error path in journal code
bcachefs: Check for invalid btree IDs
bcachefs: Fix btree ID bitmasks
bcachefs: Fix shift overflow in read_one_super()
bcachefs: Fix a locking bug in the do_discard_fast() path
...
Linus Torvalds [Sat, 22 Jun 2024 15:16:17 +0000 (08:16 -0700)]
Merge tag 'ata-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata fix from Niklas Cassel:
- We currently enable DIPM (device initiated power management) in the
device (using a SET FEATURES call to the device), regardless if the
HBA supports any LPM states or not. It seems counter intuitive, and
potentially dangerous to enable a device side feature, when the HBA
does not have the corresponding support. Thus, make sure that we do
not enable DIPM if the HBA does not support any LPM states.
* tag 'ata-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ata: ahci: Do not enable LPM if no LPM states are supported by the HBA
Linus Torvalds [Sat, 22 Jun 2024 15:03:47 +0000 (08:03 -0700)]
Merge tag 'pwm/for-6.10-rc5-fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm fixes from Uwe Kleine-König:
"Three fixes for the pwm-stm32 driver.
The first patch prevents an integer wrap-around for small periods. In
the second patch the calculation of the prescaler is fixed which
resulted in values for the ARR register that don't fit into the
corresponding register bit field. The last commit improves an error
message that was wrongly copied from another error path"
* tag 'pwm/for-6.10-rc5-fixes-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: stm32: Fix error message to not describe the previous error path
pwm: stm32: Fix calculation of prescaler
pwm: stm32: Refuse too small period requests
Linus Torvalds [Sat, 22 Jun 2024 14:58:21 +0000 (07:58 -0700)]
Merge tag 'arm-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"There are seven oneline patches that each address a distinct problem
on the NXP i.MX platform, mostly the popular i.MX8M variant.
The only other two fixes are for error handling on the psci firmware
driver and SD card support on the milkv duo riscv board"
* tag 'arm-fixes-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firmware: psci: Fix return value from psci_system_suspend()
riscv: dts: sophgo: disable write-protection for milkv duo
arm64: dts: imx8qm-mek: fix gpio number for reg_usdhc2_vmmc
arm64: dts: freescale: imx8mm-verdin: enable hysteresis on slow input pin
arm64: dts: imx93-11x11-evk: Remove the 'no-sdio' property
arm64: dts: freescale: imx8mp-venice-gw73xx-2x: fix BT shutdown GPIO
arm: dts: imx53-qsb-hdmi: Disable panel instead of deleting node
arm64: dts: imx8mp: Fix TC9595 input clock on DH i.MX8M Plus DHCOM SoM
arm64: dts: freescale: imx8mm-verdin: Fix GPU speed
Linus Torvalds [Sat, 22 Jun 2024 14:41:57 +0000 (07:41 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix dangling references to a redistributor region if the vgic was
prematurely destroyed.
- Properly mark FFA buffers as released, ensuring that both parties
can make forward progress.
x86:
- Allow getting/setting MSRs for SEV-ES guests, if they're using the
pre-6.9 KVM_SEV_ES_INIT API.
- Always sync pending posted interrupts to the IRR prior to IOAPIC
route updates, so that EOIs are intercepted properly if the old
routing table requested that.
Generic:
- Avoid __fls(0)
- Fix reference leak on hwpoisoned page
- Fix a race in kvm_vcpu_on_spin() by ensuring loads and stores are
atomic.
- Fix bug in __kvm_handle_hva_range() where KVM calls a function
pointer that was intended to be a marker only (nothing bad happens
but kind of a mine and also technically undefined behavior)
- Do not bother accounting allocations that are small and freed
before getting back to userspace.
Selftests:
- Fix compilation for RISC-V.
- Fix a "shift too big" goof in the KVM_SEV_INIT2 selftest.
- Compute the max mappable gfn for KVM selftests on x86 using
GuestMaxPhyAddr from KVM's supported CPUID (if it's available)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SEV-ES: Fix svm_get_msr()/svm_set_msr() for KVM_SEV_ES_INIT guests
KVM: Discard zero mask with function kvm_dirty_ring_reset
virt: guest_memfd: fix reference leak on hwpoisoned page
kvm: do not account temporary allocations to kmem
MAINTAINERS: Drop Wanpeng Li as a Reviewer for KVM Paravirt support
KVM: x86: Always sync PIR to IRR prior to scanning I/O APIC routes
KVM: Stop processing *all* memslots when "null" mmu_notifier handler is found
KVM: arm64: FFA: Release hyp rx buffer
KVM: selftests: Fix RISC-V compilation
KVM: arm64: Disassociate vcpus from redistributor region on teardown
KVM: Fix a data race on last_boosted_vcpu in kvm_vcpu_on_spin()
KVM: selftests: x86: Prioritize getting max_gfn from GuestPhysBits
KVM: selftests: Fix shift of 32 bit unsigned int more than 32 bits
Uwe Kleine-König [Fri, 21 Jun 2024 14:37:14 +0000 (16:37 +0200)]
pwm: stm32: Fix error message to not describe the previous error path
"Failed to lock the clock" is an appropriate error message for
clk_rate_exclusive_get() failing, but not for the clock running too
fast for the driver's calculations.
Uwe Kleine-König [Fri, 21 Jun 2024 14:37:13 +0000 (16:37 +0200)]
pwm: stm32: Fix calculation of prescaler
A small prescaler is beneficial, as this improves the resolution of the
duty_cycle configuration. However if the prescaler is too small, the
maximal possible period becomes considerably smaller than the requested
value.
One situation where this goes wrong is the following: With a parent
clock rate of 208877930 Hz and max_arr = 0xffff = 65535, a request for
period = 941243 ns currently results in PSC = 1. The value for ARR is
then calculated to
This value is bigger than 65535 however and so doesn't fit into the
respective register field. In this particular case the PWM was
configured for a period of 313733.4806027616 ns (with ARR = 98301 &
0xffff). Even if ARR was configured to its maximal value, only period =
627495.6861167669 ns would be achievable.
Fix the calculation accordingly and adapt the comment to match the new
algorithm.
With the calculation fixed the above case results in PSC = 2 and so an
actual period of 941229.1667195285 ns.
Nick Child [Thu, 20 Jun 2024 15:23:12 +0000 (10:23 -0500)]
ibmvnic: Free any outstanding tx skbs during scrq reset
There are 2 types of outstanding tx skb's:
Type 1: Packets that are sitting in the drivers ind_buff that are
waiting to be batch sent to the NIC. During a device reset, these are
freed with a call to ibmvnic_tx_scrq_clean_buffer()
Type 2: Packets that have been sent to the NIC and are awaiting a TX
completion IRQ. These are free'd during a reset with a call to
clean_tx_pools()
During any reset which requires us to free the tx irq, ensure that the
Type 2 skb references are freed. Since the irq is released, it is
impossible for the NIC to inform of any completions.
Furthermore, later in the reset process is a call to init_tx_pools()
which marks every entry in the tx pool as free (ie not outstanding).
So if the driver is to make a call to init_tx_pools(), it must first
be sure that the tx pool is empty of skb references.
This issue was discovered by observing the following in the logs during
EEH testing:
TX free map points to untracked skb (tso_pool 0 idx=4)
TX free map points to untracked skb (tso_pool 0 idx=5)
TX free map points to untracked skb (tso_pool 1 idx=36)
Fixes: 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset") Signed-off-by: Nick Child <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jakub Kicinski [Sat, 22 Jun 2024 01:15:44 +0000 (18:15 -0700)]
Merge tag 'batadv-net-pullrequest-20240621' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Don't accept TT entries for out-of-spec VIDs, by Sven Eckelmann
- Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only
callbacks", by Linus Lüssing
* tag 'batadv-net-pullrequest-20240621' of git://git.open-mesh.org/linux-merge:
Revert "batman-adv: prefer kfree_rcu() over call_rcu() with free-only callbacks"
batman-adv: Don't accept TT entries for out-of-spec VIDs
====================
Jakub Kicinski [Sat, 22 Jun 2024 01:11:30 +0000 (18:11 -0700)]
Merge tag 'linux-can-fixes-for-6.10-20240621' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2024-06-21
The first patch is by Oleksij Rempel, it enhances the error handling
for tightly received RTS message in the j1939 protocol.
Shigeru Yoshida's patch fixes a kernel information leak in
j1939_send_one() in the j1939 protocol.
Followed by a patch by Oleksij Rempel for the j1939 protocol, to
properly recover from a CAN bus error during BAM transmission.
A patch by Chen Ni properly propagates errors in the kvaser_usb
driver.
The last patch is by Vitor Soares, that fixes an infinite loop in the
mcp251xfd driver is SPI async sending fails during xmit.
* tag 'linux-can-fixes-for-6.10-20240621' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: mcp251xfd: fix infinite loop when xmit fails
can: kvaser_usb: fix return value for hif_usb_send_regout
net: can: j1939: recover socket queue on CAN bus error during BAM transmission
net: can: j1939: Initialize unused data in j1939_send_one()
net: can: j1939: enhanced error handling for tightly received RTS messages in xtp_rx_rts_session_new
====================
Guillaume Nault [Wed, 19 Jun 2024 13:34:57 +0000 (15:34 +0200)]
vxlan: Pull inner IP header in vxlan_xmit_one().
Ensure the inner IP header is part of the skb's linear data before
setting old_iph. Otherwise, on a non-linear skb, old_iph could point
outside of the packet data.
Unlike classical VXLAN, which always encapsulates Ethernet packets,
VXLAN-GPE can transport IP packets directly. In that case, we need to
look at skb->protocol to figure out if an Ethernet header is present.
Linus Torvalds [Fri, 21 Jun 2024 21:28:28 +0000 (14:28 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two fixes: one in the ufs driver fixing an obvious memory leak and the
other (with a core flag based update) trying to prevent USB crashes by
stopping the core from issuing a request for the I/O Hints mode page"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: usb: uas: Do not query the IO Advice Hints Grouping mode page for USB/UAS devices
scsi: core: Introduce the BLIST_SKIP_IO_HINTS flag
scsi: ufs: core: Free memory allocated for model before reinit
Linus Torvalds [Fri, 21 Jun 2024 21:11:50 +0000 (14:11 -0700)]
Merge tag 'drm-fixes-2024-06-22' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Still pretty quiet, two weeks worth of amdgpu fixes, with one i915 and
one xe. I didn't get the drm-misc-fixes tree PR this week, but there
was only one fix queued and I think it can wait another week, so seems
pretty normal.
xe:
- Fix for invalid register access
i915:
- Fix conditions for joiner usage, it's not possible with eDP MSO
* tag 'drm-fixes-2024-06-22' of https://gitlab.freedesktop.org/drm/kernel:
drm/xe/vf: Don't touch GuC irq registers if using memory irqs
drm/amdgpu: init TA fw for psp v14
drm/amdgpu: cleanup MES11 command submission
drm/amdgpu: fix UBSAN warning in kv_dpm.c
drm/radeon: fix UBSAN warning in kv_dpm.c
drm/amd/display: Disable CONFIG_DRM_AMD_DC_FP for RISC-V with clang
drm/amd/display: Attempt to avoid empty TUs when endpoint is DPIA
drm/amd/display: change dram_clock_latency to 34us for dcn35
drm/amd/display: Change dram_clock_latency to 34us for dcn351
drm/amdgpu: revert "take runtime pm reference when we attach a buffer" v2
drm/amdgpu: Indicate CU havest info to CP
drm/amd/display: prevent register access while in IPS
drm/amdgpu: fix locking scope when flushing tlb
drm/amd/display: Remove redundant idle optimization check
drm/i915/mso: using joiner is not possible with eDP MSO
Linus Torvalds [Fri, 21 Jun 2024 21:06:14 +0000 (14:06 -0700)]
Merge tag 'ovl-fixes-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix two bugs, one originating in this cycle and one from 6.6"
* tag 'ovl-fixes-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: fix encoding fid for lower only root
ovl: fix copy-up in tmpfile
Linus Torvalds [Fri, 21 Jun 2024 20:55:38 +0000 (13:55 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Small bug fixes:
- Prevent a crash in bnxt if the en and rdma drivers disagree on the
MSI vectors
- Have rxe memcpy inline data from the correct address
- Fix rxe's validation of UD packets
- Several mlx5 mr cache issues: bad lock balancing on error, missing
propagation of the ATS property to the HW, wrong bucketing of freed
mrs in some cases
- Incorrect goto error unwind in mlx5 driver probe
- Missed userspace input validation in mlx5 SRQ create
- Incorrect uABI in MANA rejecting valid optional MR creation flags"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mana_ib: Ignore optional access flags for MRs
RDMA/mlx5: Add check for srq max_sge attribute
RDMA/mlx5: Fix unwind flow as part of mlx5_ib_stage_init_init
RDMA/mlx5: Ensure created mkeys always have a populated rb_key
RDMA/mlx5: Follow rb_key.ats when creating new mkeys
RDMA/mlx5: Remove extra unlock on error path
RDMA/rxe: Fix responder length checking for UD request packets
RDMA/rxe: Fix data copy for IB_SEND_INLINE
RDMA/bnxt_re: Fix the max msix vectors macro
Daniel Borkmann [Fri, 21 Jun 2024 14:08:27 +0000 (16:08 +0200)]
bpf: Fix overrunning reservations in ringbuf
The BPF ring buffer internally is implemented as a power-of-2 sized circular
buffer, with two logical and ever-increasing counters: consumer_pos is the
consumer counter to show which logical position the consumer consumed the
data, and producer_pos which is the producer counter denoting the amount of
data reserved by all producers.
Each time a record is reserved, the producer that "owns" the record will
successfully advance producer counter. In user space each time a record is
read, the consumer of the data advanced the consumer counter once it finished
processing. Both counters are stored in separate pages so that from user
space, the producer counter is read-only and the consumer counter is read-write.
One aspect that simplifies and thus speeds up the implementation of both
producers and consumers is how the data area is mapped twice contiguously
back-to-back in the virtual memory, allowing to not take any special measures
for samples that have to wrap around at the end of the circular buffer data
area, because the next page after the last data page would be first data page
again, and thus the sample will still appear completely contiguous in virtual
memory.
Each record has a struct bpf_ringbuf_hdr { u32 len; u32 pg_off; } header for
book-keeping the length and offset, and is inaccessible to the BPF program.
Helpers like bpf_ringbuf_reserve() return `(void *)hdr + BPF_RINGBUF_HDR_SZ`
for the BPF program to use. Bing-Jhong and Muhammad reported that it is however
possible to make a second allocated memory chunk overlapping with the first
chunk and as a result, the BPF program is now able to edit first chunk's
header.
For example, consider the creation of a BPF_MAP_TYPE_RINGBUF map with size
of 0x4000. Next, the consumer_pos is modified to 0x3000 /before/ a call to
bpf_ringbuf_reserve() is made. This will allocate a chunk A, which is in
[0x0,0x3008], and the BPF program is able to edit [0x8,0x3008]. Now, lets
allocate a chunk B with size 0x3000. This will succeed because consumer_pos
was edited ahead of time to pass the `new_prod_pos - cons_pos > rb->mask`
check. Chunk B will be in range [0x3008,0x6010], and the BPF program is able
to edit [0x3010,0x6010]. Due to the ring buffer memory layout mentioned
earlier, the ranges [0x0,0x4000] and [0x4000,0x8000] point to the same data
pages. This means that chunk B at [0x4000,0x4008] is chunk A's header.
bpf_ringbuf_submit() / bpf_ringbuf_discard() use the header's pg_off to then
locate the bpf_ringbuf itself via bpf_ringbuf_restore_from_rec(). Once chunk
B modified chunk A's header, then bpf_ringbuf_commit() refers to the wrong
page and could cause a crash.
Fix it by calculating the oldest pending_pos and check whether the range
from the oldest outstanding record to the newest would span beyond the ring
buffer size. If that is the case, then reject the request. We've tested with
the ring buffer benchmark in BPF selftests (./benchs/run_bench_ringbufs.sh)
before/after the fix and while it seems a bit slower on some benchmarks, it
is still not significantly enough to matter.
Linus Torvalds [Fri, 21 Jun 2024 18:26:43 +0000 (11:26 -0700)]
Merge tag 'sound-6.10-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"A follow-up fix for a random build issue, as well as another trivial
HD-audio quirk"
* tag 'sound-6.10-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: Use imply for suggesting CONFIG_SERIAL_MULTI_INSTANTIATE
ALSA: hda/realtek: Add quirk for Lenovo Yoga Pro 7 14AHP9
Linus Torvalds [Fri, 21 Jun 2024 18:20:37 +0000 (11:20 -0700)]
Merge tag 'acpi-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These address a possible NULL pointer dereference in the ACPICA code
and quirk camera enumeration on multiple platforms where incorrect
data are present in the platform firmware.
Specifics:
- Undo an ACPICA code change that attempted to keep operation regions
within a page boundary, but allowed accesses to unmapped memory to
occur (Raju Rangoju)
- Ignore MIPI camera graph port nodes created with the help of the
information from the ACPI tables on all Dell Tiger, Alder and
Raptor Lake models as that information is reported to be invalid on
the platforms in question (Hans de Goede)
- Use new Intel CPU model matching macros in the MIPI DisCo for
Imaging part of ACPI device enumeration (Hans de Goede)"
* tag 'acpi-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: mipi-disco-img: Switch to new Intel CPU model defines
ACPI: scan: Ignore camera graph port nodes on all Dell Tiger, Alder and Raptor Lake models
ACPICA: Revert "ACPICA: avoid Info: mapping multiple BARs. Your kernel is fine."
bpf: Fix the corner case with may_goto and jump to the 1st insn.
When the following program is processed by the verifier:
L1: may_goto L2
goto L1
L2: w0 = 0
exit
the may_goto insn is first converted to:
L1: r11 = *(u64 *)(r10 -8)
if r11 == 0x0 goto L2
r11 -= 1
*(u64 *)(r10 -8) = r11
goto L1
L2: w0 = 0
exit
then later as the last step the verifier inserts:
*(u64 *)(r10 -8) = BPF_MAX_LOOPS
as the first insn of the program to initialize loop count.
When the first insn happens to be a branch target of some jmp the
bpf_patch_insn_data() logic will produce:
L1: *(u64 *)(r10 -8) = BPF_MAX_LOOPS
r11 = *(u64 *)(r10 -8)
if r11 == 0x0 goto L2
r11 -= 1
*(u64 *)(r10 -8) = r11
goto L1
L2: w0 = 0
exit
because instruction patching adjusts all jmps and calls, but for this
particular corner case it's incorrect and the L1 label should be one
instruction down, like:
*(u64 *)(r10 -8) = BPF_MAX_LOOPS
L1: r11 = *(u64 *)(r10 -8)
if r11 == 0x0 goto L2
r11 -= 1
*(u64 *)(r10 -8) = r11
goto L1
L2: w0 = 0
exit
and that's what this patch is fixing.
After bpf_patch_insn_data() call adjust_jmp_off() to adjust all jmps
that point to newly insert BPF_ST insn to point to insn after.
Note that bpf_patch_insn_data() cannot easily be changed to accommodate
this logic, since jumps that point before or after a sequence of patched
instructions have to be adjusted with the full length of the patch.
Conceptually it's somewhat similar to "insert" of instructions between other
instructions with weird semantics. Like "insert" before 1st insn would require
adjustment of CALL insns to point to newly inserted 1st insn, but not an
adjustment JMP insns that point to 1st, yet still adjusting JMP insns that
cross over 1st insn (point to insn before or insn after), hence use simple
adjust_jmp_off() logic to fix this corner case. Ideally bpf_patch_insn_data()
would have an auxiliary info to say where 'the start of newly inserted patch
is', but it would be too complex for backport.
Linus Torvalds [Fri, 21 Jun 2024 18:16:56 +0000 (11:16 -0700)]
Merge tag 'thermal-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix the Mediatek lvts_thermal driver, the Intel int340x driver,
and the thermal core (two issues related to system suspend).
Specifics:
- Remove the filtered mode for mt8188 from lvts_thermal as it is not
supported on this platform and fail the lvts_thermal initialization
when the golden temperature is zero as that means the efuse data is
not correctly set (Julien Panis)
- Update the processor_thermal part of the Intel int340x driver to
support shared interrupts as the processor thermal device interrupt
may in fact be shared with PCI devices (Srinivas Pandruvada)
- Synchronize the suspend-prepare and post-suspend actions of the
thermal PM notifier to avoid a destructive race condition and
change the priority of that notifier to the minimum to avoid
interference between the work items spawned by it and the other
PM notifiers during system resume (Rafael Wysocki)"
* tag 'thermal-6.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: processor_thermal: Support shared interrupts
thermal: core: Change PM notifier priority to the minimum
thermal: core: Synchronize suspend-prepare and post-suspend actions
thermal/drivers/mediatek/lvts_thermal: Return error in case of invalid efuse data
thermal/drivers/mediatek/lvts_thermal: Remove filtered mode for mt8188
Kent Overstreet [Thu, 20 Jun 2024 17:20:49 +0000 (13:20 -0400)]
bcachefs: Fix I_NEW warning in race path in bch2_inode_insert()
discard_new_inode() is the correct interface for tearing down an indoe
that was fully created but not made visible to other threads, but it
expects I_NEW to be set, which we don't use.
Reported-by: https://github.com/koverstreet/bcachefs/issues/690 Fixes: bcachefs: Fix race path in bch2_inode_insert() Signed-off-by: Kent Overstreet <[email protected]>
Kent Overstreet [Thu, 20 Jun 2024 14:04:35 +0000 (10:04 -0400)]
bcachefs: Fix missing alloc_data_type_set()
Incorrect bucket state transition in the discard path; when incrementing
a bucket's generation number that had already been discarded, we were
forgetting to check if it should be need_gc_gens, not free.
This was caught by the .invalid checks in the transaction commit path,
causing us to go emergency read only.
The register has two masks of 256 bits to denote on which ingress /
egress ports the register should operate on. Spectrum-4 has more than
256 ports, so the register was extended by cited commit with a new
'port_page' field.
However, when filling the register's payload, the driver specifies the
ports as absolute numbers and not relative to the first port of the port
page, resulting in memory corruptions [1].
Fix by specifying the ports relative to the first port of the port page.
Ido Schimmel [Fri, 21 Jun 2024 07:19:13 +0000 (09:19 +0200)]
mlxsw: pci: Fix driver initialization with Spectrum-4
Cited commit added support for a new reset flow ("all reset") which is
deeper than the existing reset flow ("software reset") and allows the
device's PCI firmware to be upgraded.
In the new flow the driver first tells the firmware that "all reset" is
required by issuing a new reset command (i.e., MRSR.command=6) and then
triggers the reset by having the PCI core issue a secondary bus reset
(SBR).
However, due to a race condition in the device's firmware the device is
not always able to recover from this reset, resulting in initialization
failures [1].
New firmware versions include a fix for the bug and advertise it using a
new capability bit in the Management Capabilities Mask (MCAM) register.
Avoid initialization failures by reading the new capability bit and
triggering the new reset flow only if the bit is set. If the bit is not
set, trigger a normal PCI hot reset by skipping the call to the
Management Reset and Shutdown Register (MRSR).
Normal PCI hot reset is weaker than "all reset", but it results in a
fully operational driver and allows users to flash a new firmware, if
they want to.
[1]
mlxsw_spectrum4 0000:01:00.0: not ready 1023ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 2047ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 4095ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 8191ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 16383ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 32767ms after bus reset; waiting
mlxsw_spectrum4 0000:01:00.0: not ready 65535ms after bus reset; giving up
mlxsw_spectrum4 0000:01:00.0: PCI function reset failed with -25
mlxsw_spectrum4 0000:01:00.0: cannot register bus device
mlxsw_spectrum4: probe of 0000:01:00.0 failed with error -25
diag_uid selftest failed on NIPA where the received nlmsg_type is
NLMSG_ERROR [0] because CONFIG_UNIX_DIAG is not set [1] by default
and sock_diag_lock_handler() failed to load the module.
# # Starting 2 tests from 2 test cases.
# # RUN diag_uid.uid.1 ...
# # diag_uid.c:159:1:Expected nlh->nlmsg_type (2) == SOCK_DIAG_BY_FAMILY (20)
# # 1: Test terminated by assertion
# # FAIL diag_uid.uid.1
# not ok 1 diag_uid.uid.1
Let's add all AF_UNIX Kconfig to the config file under af_unix dir
so that NIPA consumes it.
max_sge attribute is passed by the user, and is inserted and used
unchecked, so verify that the value doesn't exceed maximum allowed value
before using it.
Jason Gunthorpe [Tue, 28 May 2024 12:52:53 +0000 (15:52 +0300)]
RDMA/mlx5: Follow rb_key.ats when creating new mkeys
When a cache ent already exists but doesn't have any mkeys in it the cache
will automatically create a new one based on the specification in the
ent->rb_key.
ent->ats was missed when creating the new key and so ma_translation_mode
was not being set even though the ent requires it.
Jason Gunthorpe [Tue, 28 May 2024 12:52:52 +0000 (15:52 +0300)]
RDMA/mlx5: Remove extra unlock on error path
The below commit lifted the locking out of this function but left this
error path unlock behind resulting in unbalanced locking. Remove the
missed unlock too.
Eric Dumazet [Thu, 20 Jun 2024 13:31:19 +0000 (13:31 +0000)]
net: add softirq safety to netdev_rename_lock
syzbot reported a lockdep violation involving bridge driver [1]
Make sure netdev_rename_lock is softirq safe to fix this issue.
[1]
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected 6.10.0-rc2-syzkaller-00249-gbe27b8965297 #0 Not tainted
-----------------------------------------------------
syz-executor.2/9449 [HC0[0]:SC0[2]:HE0:SE0] is trying to acquire: ffffffff8f5de668 (netdev_rename_lock.seqcount){+.+.}-{0:0}, at: rtnl_fill_ifinfo+0x38e/0x2270 net/core/rtnetlink.c:1839
and this task is already holding: ffff888060c64cb8 (&br->lock){+.-.}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline] ffff888060c64cb8 (&br->lock){+.-.}-{2:2}, at: br_port_slave_changelink+0x3d/0x150 net/bridge/br_netlink.c:1212
which would create a new lock dependency:
(&br->lock){+.-.}-{2:2} -> (netdev_rename_lock.seqcount){+.+.}-{0:0}
but this new dependency connects a SOFTIRQ-irq-safe lock:
(&br->lock){+.-.}-{2:2}
Michael Roth [Tue, 4 Jun 2024 23:35:10 +0000 (18:35 -0500)]
KVM: SEV-ES: Fix svm_get_msr()/svm_set_msr() for KVM_SEV_ES_INIT guests
With commit 27bd5fdc24c0 ("KVM: SEV-ES: Prevent MSR access post VMSA
encryption"), older VMMs like QEMU 9.0 and older will fail when booting
SEV-ES guests with something like the following error:
qemu-system-x86_64: error: failed to get MSR 0x174
qemu-system-x86_64: ../qemu.git/target/i386/kvm/kvm.c:3950: kvm_get_msrs: Assertion `ret == cpu->kvm_msr_buf->nmsrs' failed.
This is because older VMMs that might still call
svm_get_msr()/svm_set_msr() for SEV-ES guests after guest boot even if
those interfaces were essentially just noops because of the vCPU state
being encrypted and stored separately in the VMSA. Now those VMMs will
get an -EINVAL and generally crash.
Newer VMMs that are aware of KVM_SEV_INIT2 however are already aware of
the stricter limitations of what vCPU state can be sync'd during
guest run-time, so newer QEMU for instance will work both for legacy
KVM_SEV_ES_INIT interface as well as KVM_SEV_INIT2.
So when using KVM_SEV_INIT2 it's okay to assume userspace can deal with
-EINVAL, whereas for legacy KVM_SEV_ES_INIT the kernel might be dealing
with either an older VMM and so it needs to assume that returning
-EINVAL might break the VMM.
Address this by only returning -EINVAL if the guest was started with
KVM_SEV_INIT2. Otherwise, just silently return.
- Ignore MIPI camera graph port nodes created with the help of the
information from the ACPI tables on all Dell Tiger, Alder and Raptor
Lake models as that information is reported to be invalid on the
systems in question (Hans de Goede).
- Use new Intel CPU model matching macros in the MIPI DisCo for Imaging
part of ACPI device enumeration (Hans de Goede).
* acpi-scan:
ACPI: mipi-disco-img: Switch to new Intel CPU model defines
ACPI: scan: Ignore camera graph port nodes on all Dell Tiger, Alder and Raptor Lake models
Taehee Yoo [Thu, 20 Jun 2024 10:58:08 +0000 (10:58 +0000)]
ionic: fix kernel panic due to multi-buffer handling
Currently, the ionic_run_xdp() doesn't handle multi-buffer packets
properly for XDP_TX and XDP_REDIRECT.
When a jumbo frame is received, the ionic_run_xdp() first makes xdp
frame with all necessary pages in the rx descriptor.
And if the action is either XDP_TX or XDP_REDIRECT, it should unmap
dma-mapping and reset page pointer to NULL for all pages, not only the
first page.
But it doesn't for SG pages. So, SG pages unexpectedly will be reused.
It eventually causes kernel panic.
Selecting FW_UPLOAD is not sufficient as it allows the firmware loader
API to be built as a module alongside the pd692x0 driver built as builtin.
Add select FW_LOADER to fix this issue.
The __ethtool_get_ts_info function returns directly if the device has a
get_ts_info() method. For bonding with an active slave, this works correctly
as we simply return the real device's timestamping information. However,
when there is no active slave, we only check the slave's TX software
timestamp information. We still need to set the phc index and RX timestamp
information manually. Otherwise, the result will be look like:
Takashi Iwai [Fri, 21 Jun 2024 07:39:09 +0000 (09:39 +0200)]
ALSA: hda: Use imply for suggesting CONFIG_SERIAL_MULTI_INSTANTIATE
The recent fix introduced a reverse selection of
CONFIG_SERIAL_MULTI_INSTANTIATE, but its condition isn't always met.
Use a weak reverse selection to suggest the config for avoiding such
inconsistencies, instead.
Xin Long [Wed, 19 Jun 2024 22:08:56 +0000 (18:08 -0400)]
openvswitch: get related ct labels from its master if it is not confirmed
Ilya found a failure in running check-kernel tests with at_groups=144
(144: conntrack - FTP SNAT orig tuple) in OVS repo. After his further
investigation, the root cause is that the labels sent to userspace
for related ct are incorrect.
The labels for unconfirmed related ct should use its master's labels.
However, the changes made in commit 8c8b73320805 ("openvswitch: set
IPS_CONFIRMED in tmpl status only when commit is set in conntrack")
led to getting labels from this related ct.
So fix it in ovs_ct_get_labels() by changing to copy labels from its
master ct if it is a unconfirmed related ct. Note that there is no
fix needed for ct->mark, as it was already copied from its master
ct for related ct in init_conntrack().
Vitor Soares [Fri, 17 May 2024 13:43:55 +0000 (14:43 +0100)]
can: mcp251xfd: fix infinite loop when xmit fails
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
Oleksij Rempel [Tue, 28 May 2024 07:06:48 +0000 (09:06 +0200)]
net: can: j1939: recover socket queue on CAN bus error during BAM transmission
Addresses an issue where a CAN bus error during a BAM transmission
could stall the socket queue, preventing further transmissions even
after the bus error is resolved. The fix activates the next queued
session after the error recovery, allowing communication to continue.
Shigeru Yoshida [Fri, 17 May 2024 03:59:53 +0000 (12:59 +0900)]
net: can: j1939: Initialize unused data in j1939_send_one()
syzbot reported kernel-infoleak in raw_recvmsg() [1]. j1939_send_one()
creates full frame including unused data, but it doesn't initialize
it. This causes the kernel-infoleak issue. Fix this by initializing
unused data.
Oleksij Rempel [Fri, 17 Nov 2023 12:49:59 +0000 (13:49 +0100)]
net: can: j1939: enhanced error handling for tightly received RTS messages in xtp_rx_rts_session_new
This patch enhances error handling in scenarios with RTS (Request to
Send) messages arriving closely. It replaces the less informative WARN_ON_ONCE
backtraces with a new error handling method. This provides clearer error
messages and allows for the early termination of problematic sessions.
Previously, sessions were only released at the end of j1939_xtp_rx_rts().
Arnd Bergmann [Thu, 20 Jun 2024 16:23:04 +0000 (18:23 +0200)]
mips: fix compat_sys_lseek syscall
This is almost compatible, but passing a negative offset should result
in a EINVAL error, but on mips o32 compat mode would seek to a large
32-bit byte offset.
Use compat_sys_lseek() to correctly sign-extend the argument.
Tristram Ha [Wed, 19 Jun 2024 00:16:42 +0000 (17:16 -0700)]
net: dsa: microchip: fix initial port flush problem
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
In the current code, if multiple hardware breakpoints/watchpoints in
a user-space thread, some of them will not be triggered.
When debugging the following code using gdb.
lihui@bogon:~$ cat test.c
#include <stdio.h>
int a = 0;
int main()
{
printf("start test\n");
a = 1;
printf("a = %d\n", a);
printf("end test\n");
return 0;
}
lihui@bogon:~$ gcc -g test.c -o test
lihui@bogon:~$ gdb test
...
(gdb) start
...
Temporary breakpoint 1, main () at test.c:5
5 printf("start test\n");
(gdb) watch a
Hardware watchpoint 2: a
(gdb) hbreak 8
Hardware assisted breakpoint 3 at 0x1200006ec: file test.c, line 8.
(gdb) c
Continuing.
start test
a = 1
Breakpoint 3, main () at test.c:8
8 printf("end test\n");
...
The first hardware watchpoint is not triggered, the root causes are:
1. In hw_breakpoint_control(), The FWPnCFG1.2.4/MWPnCFG1.2.4 register
settings are not distinguished. They should be set based on hardware
watchpoint functions (fetch or load/store operations).
2. In breakpoint_handler() and watchpoint_handler(), it doesn't identify
which watchpoint is triggered. So, all watchpoint-related perf_event
callbacks are called and siginfo is sent to the user space. This will
cause user-space unable to determine which watchpoint is triggered.
The kernel need to identity which watchpoint is triggered via MWPS/
FWPS registers, and then call the corresponding perf event callbacks
to report siginfo to the user-space.
Modify the relevant code to solve above issues.
All changes according to the LoongArch Reference Manual:
https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
With this patch:
lihui@bogon:~$ gdb test
...
(gdb) start
...
Temporary breakpoint 1, main () at test.c:5
5 printf("start test\n");
(gdb) watch a
Hardware watchpoint 2: a
(gdb) hbreak 8
Hardware assisted breakpoint 3 at 0x1200006ec: file test.c, line 8.
(gdb) c
Continuing.
start test
Hardware watchpoint 2: a
Old value = 0
New value = 1
main () at test.c:7
7 printf("a = %d\n", a);
(gdb) c
Continuing.
a = 1
Breakpoint 3, main () at test.c:8
8 printf("end test\n");
(gdb) c
Continuing.
end test
[Inferior 1 (process 778) exited normally]
In the current code, gdb can set the watchpoint successfully through
ptrace interface, but watchpoint will not be triggered.
When debugging the following code using gdb.
lihui@bogon:~$ cat test.c
#include <stdio.h>
int a = 0;
int main()
{
a = 1;
printf("a = %d\n", a);
return 0;
}
lihui@bogon:~$ gcc -g test.c -o test
lihui@bogon:~$ gdb test
...
(gdb) watch a
...
(gdb) r
...
a = 1
[Inferior 1 (process 4650) exited normally]
No watchpoints were triggered, the root causes are:
1. Kernel uses perf_event and hw_breakpoint framework to control
watchpoint, but the perf_event corresponding to watchpoint is
not enabled. So it needs to be enabled according to MWPnCFG3
or FWPnCFG3 PLV bit field in ptrace_hbp_set_ctrl(), and privilege
is set according to the monitored addr in hw_breakpoint_control().
Furthermore, add a judgment in ptrace_hbp_set_addr() to ensure
kernel-space addr cannot be monitored in user mode.
2. The global enable control for all watchpoints is the WE bit of
CSR.CRMD, and hardware sets the value to 0 when an exception is
triggered. When the ERTN instruction is executed to return, the
hardware restores the value of the PWE field of CSR.PRMD here.
So, before a thread containing watchpoints be scheduled, the PWE
field of CSR.PRMD needs to be set to 1. Add this modification in
hw_breakpoint_control().
All changes according to the LoongArch Reference Manual:
https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#basic-control-and-status-registers
With this patch:
lihui@bogon:~$ gdb test
...
(gdb) watch a
Hardware watchpoint 1: a
(gdb) r
...
Hardware watchpoint 1: a
Old value = 0
New value = 1
main () at test.c:6
6 printf("a = %d\n", a);
(gdb) c
Continuing.
a = 1
[Inferior 1 (process 775) exited normally]
Hui Li [Fri, 21 Jun 2024 02:18:40 +0000 (10:18 +0800)]
LoongArch: Fix watchpoint setting error
In the current code, when debugging the following code using gdb,
"invalid argument ..." message will be displayed.
lihui@bogon:~$ cat test.c
#include <stdio.h>
int a = 0;
int main()
{
a = 1;
return 0;
}
lihui@bogon:~$ gcc -g test.c -o test
lihui@bogon:~$ gdb test
...
(gdb) watch a
Hardware watchpoint 1: a
(gdb) r
...
Invalid argument setting hardware debug registers
There are mainly two types of issues.
1. Some incorrect judgment condition existed in user_watch_state
argument parsing, causing -EINVAL to be returned.
When setting up a watchpoint, gdb uses the ptrace interface,
ptrace(PTRACE_SETREGSET, tid, NT_LOONGARCH_HW_WATCH, (void *) &iov)).
Register values in user_watch_state as follows:
In arch_bp_generic_fields(), return -EINVAL when ctrl.len is
LOONGARCH_BREAKPOINT_LEN_8(0b00). So delete the incorrect judgment here.
In ptrace_hbp_fill_attr_ctrl(), when note_type is NT_LOONGARCH_HW_WATCH
and ctrl[0] == 0x0, if ((type & HW_BREAKPOINT_RW) != type) will return
-EINVAL. Here ctrl.type should be set based on note_type, and unnecessary
judgments can be removed.
2. The watchpoint argument was not set correctly due to unnecessary
offset and alignment_mask.
Modify ptrace_hbp_fill_attr_ctrl() and hw_breakpoint_arch_parse(), which
ensure the watchpont argument is set correctly.
All changes according to the LoongArch Reference Manual:
https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#control-and-status-registers-related-to-watchpoints
Xi Ruoyao [Fri, 21 Jun 2024 02:18:40 +0000 (10:18 +0800)]
LoongArch: Only allow OBJTOOL & ORC unwinder if toolchain supports -mthin-add-sub
GAS <= 2.41 does not support generating R_LARCH_{32,64}_PCREL for
"label - ." and it generates R_LARCH_{ADD,SUB}{32,64} pairs instead.
Objtool cannot handle R_LARCH_{ADD,SUB}{32,64} pair in __jump_table
(static key implementation) and etc. so it will produce some warnings.
This is causing the kernel CI systems to complain everywhere.
For GAS we can check if -mthin-add-sub option is available to know if
R_LARCH_{32,64}_PCREL are supported.
For Clang, we require Clang >= 18 and Clang >= 17 already supports
R_LARCH_{32,64}_PCREL. But unfortunately Clang has some other issues,
so we disable objtool for Clang at present.
Note that __jump_table here is not generated by the compiler, so
-fno-jump-table is completely irrelevant for this issue.
projects / linux.git / log