Christoph Egger [Mon, 17 May 2010 15:25:54 +0000 (17:25 +0200)]
serial: Tidy REMOTE_DEBUG
REMOTE_DEBUG does already appear in 2.2 kernel sources but didn't
appear as a config Option in the initial git import 2.6.12-rc. It's
currently just used in one single place of the linux kernel and should
probably be dropped totally
Dan Carpenter [Fri, 7 May 2010 08:30:41 +0000 (10:30 +0200)]
serial: isicomm: handle running out of slots
This patch makes it return -ENODEV if we run out of empty slots in the
probe function. It's unlikely to happen, but it makes the static
checkers happy.
Richard Röjfors [Tue, 27 Apr 2010 21:16:34 +0000 (14:16 -0700)]
serial: timbuart: make sure last byte is sent when port is closed
Fix a problem in early versions of the FPGA IP.
In certain situations the IP reports that the FIFO is empty, but a byte is
still clocked out. If a flush is done at that point the currently clocked
byte is canceled.
This causes incompatibilities with the upper layers when a port is closed,
it waits until the FIFO is empty and then closes the port. During close
the FIFO is flushed -> the last byte is not sent properly.
Now the FIFO is only flushed if it is reported to be non-empty. Which
makes the currently clocked out byte to finish.
Randy Dunlap [Mon, 3 May 2010 16:08:38 +0000 (09:08 -0700)]
tty: n_gsm: depends on NET
n_gsm uses skb functions, so it should depend on NET.
n_gsm.c:(.text+0x123d49): undefined reference to `skb_dequeue'
n_gsm.c:(.text+0x123d98): undefined reference to `kfree_skb'
n_gsm.c:(.text+0x123e1e): undefined reference to `skb_pull'
Alan Cox [Fri, 26 Mar 2010 11:32:54 +0000 (11:32 +0000)]
tty: n_gsm line discipline
Add an implementation of GSM 0710 MUX. The implementation currently supports
- Basic and advanced framing (as either end of the link)
- UI or UIH data frames
- Adaption layer 1-4 (1 and 2 via tty, 3 and 4 as skbuff lists)
- Modem and control messages including the correct retry process
- Flow control
and exposes the MUX channels as a set of virtual tty devices including modem
signals. This is an experimental driver.
Sonic Zhang [Tue, 9 Mar 2010 17:25:37 +0000 (12:25 -0500)]
serial: bfin_sport_uart: only enable SPORT TX if data is to be sent
Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission. This avoids useless interrupt
processing.
Sonic Zhang [Tue, 9 Mar 2010 17:25:29 +0000 (12:25 -0500)]
serial: bfin_sport_uart: shorten the SPORT TX waiting loop
The waiting loop to stop SPORT TX from TX interrupt is too long. This may
block the SPORT RX interrupts and cause the RX FIFO to overflow. So, do
stop sport TX only after the last char in TX FIFO is moved into the shift
register.
Linus Torvalds [Fri, 21 May 2010 14:47:00 +0000 (07:47 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (23 commits)
nilfs2: disallow remount of snapshot from/to a regular mount
nilfs2: use huge_encode_dev/huge_decode_dev
nilfs2: update comment on deactivate_super at nilfs_get_sb
nilfs2: replace MS_VERBOSE with MS_SILENT
nilfs2: add missing initialization of s_mode
nilfs2: fix misuse of open_bdev_exclusive/close_bdev_exclusive
nilfs2: enlarge s_volume_name member in nilfs_super_block
nilfs2: use checkpoint number instead of timestamp to select super block
nilfs2: add missing endian conversion on super block magic number
nilfs2: make nilfs_sc_*_ops static
nilfs2: add kernel doc comments to persistent object allocator functions
nilfs2: change sc_timer from a pointer to an embedded one in struct nilfs_sc_info
nilfs2: remove nilfs_segctor_init() in segment.c
nilfs2: insert checkpoint number in segment summary header
nilfs2: add a print message after loading nilfs2
nilfs2: cleanup multi kmem_cache_{create,destroy} code
nilfs2: move out checksum routines to segment buffer code
nilfs2: move pointer to super root block into logs
nilfs2: change default of 'errors' mount option to 'remount-ro' mode
nilfs2: Combine nilfs_btree_release_path() and nilfs_btree_free_path()
...
Linus Torvalds [Fri, 21 May 2010 14:25:43 +0000 (07:25 -0700)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
Linus Torvalds [Fri, 21 May 2010 14:23:12 +0000 (07:23 -0700)]
Merge branch 'linux-next' of git://git.infradead.org/ubi-2.6
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: misc comment fixes
UBI: fix s/then/than/ typos
UBI: init even if MTD device cannot be attached, if built into kernel
UBI: remove reboot notifier
Linus Torvalds [Fri, 21 May 2010 14:22:11 +0000 (07:22 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (54 commits)
xfs: mark xfs_iomap_write_ helpers static
xfs: clean up end index calculation in xfs_page_state_convert
xfs: clean up mapping size calculation in __xfs_get_blocks
xfs: clean up xfs_iomap_valid
xfs: move I/O type flags into xfs_aops.c
xfs: kill struct xfs_iomap
xfs: report iomap_bn in block base
xfs: report iomap_offset and iomap_bsize in block base
xfs: remove iomap_delta
xfs: remove iomap_target
xfs: limit xfs_imap_to_bmap to a single mapping
xfs: simplify buffer to transaction matching
xfs: Make fiemap work in query mode.
xfs: kill off l_sectbb_mask
xfs: record log sector size rather than log2(that)
xfs: remove dead XFS_LOUD_RECOVERY code
xfs: removed unused XFS_QMOPT_ flags
xfs: remove a few macro indirections in the quota code
xfs: access quotainfo structure directly
xfs: wait for direct I/O to complete in fsync and write_inode
...
Linus Torvalds [Fri, 21 May 2010 14:20:17 +0000 (07:20 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (47 commits)
ocfs2: Silence a gcc warning.
ocfs2: Don't retry xattr set in case value extension fails.
ocfs2:dlm: avoid dlm->ast_lock lockres->spinlock dependency break
ocfs2: Reset xattr value size after xa_cleanup_value_truncate().
fs/ocfs2/dlm: Use kstrdup
fs/ocfs2/dlm: Drop memory allocation cast
Ocfs2: Optimize punching-hole code.
Ocfs2: Make ocfs2_find_cpos_for_left_leaf() public.
Ocfs2: Fix hole punching to correctly do CoW during cluster zeroing.
Ocfs2: Optimize ocfs2 truncate to use ocfs2_remove_btree_range() instead.
ocfs2: Block signals for mkdir/link/symlink/O_CREAT.
ocfs2: Wrap signal blocking in void functions.
ocfs2/dlm: Increase o2dlm lockres hash size
ocfs2: Make ocfs2_extend_trans() really extend.
ocfs2/trivial: Code cleanup for allocation reservation.
ocfs2: make ocfs2_adjust_resv_from_alloc simple.
ocfs2: Make nointr a default mount option
ocfs2/dlm: Make o2dlm domain join/leave messages KERN_NOTICE
o2net: log socket state changes
ocfs2: print node # when tcp fails
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
Jiri Kosina [Fri, 21 May 2010 11:15:17 +0000 (13:15 +0200)]
HID: fix up 'EMBEDDED' mess in Kconfig
The whole point of making some of the drivers automatically selected
unless 'EMBEDDED' was to handle quirks transparently after their separation
from the generic core.
Over time, some of the later-added quirks grew into more standalone drivers,
implementing non-trivial features a being larger than a few bytes of code.
In addition to that, some of the standalone drivers don't make sense for
99.9% of the users, as they are very specific to rare devices.
Therefore build by default in only those drivers which
- we historically used to support even before quirk separation from the
core code
- are isolated enough and likely to hit quite large portion of the
users anyway (Microsoft, Logitech)
In 2008, the IOMMU was fixed to use the boundary_mask parameter per
device properly. So 'protect4gb' workaround was removed (the 383af9525bb27f927511874f6306247ec13f1c28). But somehow I messed the
'protect4gb' boot parameter that was used to enable the
workaround.
Mark Nelson [Tue, 18 May 2010 22:51:00 +0000 (22:51 +0000)]
powerpc/pseries: Make request_ras_irqs() available to other pseries code
At the moment only the RAS code uses event-sources interrupts (for EPOW
events and internal errors) so request_ras_irqs() (which actually requests
the event-sources interrupts) is found in ras.c and is static.
We want to be able to use event-sources interrupts in other pseries code,
so let's rename request_ras_irqs() to request_event_sources_irqs() and
move it to event_sources.c.
This will be used in an upcoming patch that adds support for IO Event
interrupts that come through as event sources.
Anton Blanchard [Sun, 16 May 2010 20:28:35 +0000 (20:28 +0000)]
powerpc/numa: Use ibm,architecture-vec-5 to detect form 1 affinity
I've been told that the architected way to determine we are in form 1
affinity mode is by reading the ibm,architecture-vec-5 property which
mirrors the layout of the fifth vector of the ibm,client-architecture
structure.
Eventually we may want to parse the ibm,architecture-vec-5 and create
FW_FEATURE_* bits.
Anton Blanchard [Sun, 16 May 2010 20:19:56 +0000 (20:19 +0000)]
powerpc/numa: Set a smaller value for RECLAIM_DISTANCE to enable zone reclaim
I noticed /proc/sys/vm/zone_reclaim_mode was 0 on a ppc64 NUMA box. It gets
enabled via this:
/*
* If another node is sufficiently far away then it is better
* to reclaim pages in a zone before going off node.
*/
if (distance > RECLAIM_DISTANCE)
zone_reclaim_mode = 1;
Since we use the default value of 20 for REMOTE_DISTANCE and 20 for
RECLAIM_DISTANCE it never kicks in.
The local to remote bandwidth ratios can be quite large on System p
machines so it makes sense for us to reclaim clean pagecache locally before
going off node.
The patch below sets a smaller value for RECLAIM_DISTANCE and thus enables
zone reclaim.
Anton Blanchard [Sun, 16 May 2010 20:02:39 +0000 (20:02 +0000)]
powerpc: Use smt_snooze_delay=-1 to always busy loop
Right now if we want to busy loop and not give up any time to the hypervisor
we put a very large value into smt_snooze_delay. This is sometimes useful
when running a single partition and you want to avoid any latencies due
to the hypervisor or CPU power state transitions. While this works, it's a bit
ugly - how big a number is enough now we have NO_HZ and can be idle for a very
long time.
The patch below makes smt_snooze_delay signed, and a negative value means loop
forever:
Anton Blanchard [Sun, 16 May 2010 20:01:28 +0000 (20:01 +0000)]
powerpc: Remove check of ibm,smt-snooze-delay OF property
I'm not sure why we have code for parsing an ibm,smt-snooze-delay OF
property. Since we have a smt-snooze-delay= boot option and we can
also set it at runtime via sysfs, it should be safe to get rid of
this code.
Michael Neuling [Thu, 13 May 2010 19:40:11 +0000 (19:40 +0000)]
powerpc/kdump: Fix race in kdump shutdown
When we are crashing, the crashing/primary CPU IPIs the secondaries to
turn off IRQs, go into real mode and wait in kexec_wait. While this
is happening, the primary tears down all the MMU maps. Unfortunately
the primary doesn't check to make sure the secondaries have entered
real mode before doing this.
On PHYP machines, the secondaries can take a long time shutting down
the IRQ controller as RTAS calls are need. These RTAS calls need to
be serialised which resilts in the secondaries contending in
lock_rtas() and hence taking a long time to shut down.
We've hit this on large POWER7 machines, where some secondaries are
still waiting in lock_rtas(), when the primary tears down the HPTEs.
This patch makes sure all secondaries are in real mode before the
primary tears down the MMU. It uses the new kexec_state entry in the
paca. It times out if the secondaries don't reach real mode after
10sec.
Michael Neuling [Thu, 13 May 2010 19:40:11 +0000 (19:40 +0000)]
powerpc/kexec: Fix race in kexec shutdown
In kexec_prepare_cpus, the primary CPU IPIs the secondary CPUs to
kexec_smp_down(). kexec_smp_down() calls kexec_smp_wait() which sets
the hw_cpu_id() to -1. The primary does this while leaving IRQs on
which means the primary can take a timer interrupt which can lead to
the IPIing one of the secondary CPUs (say, for a scheduler re-balance)
but since the secondary CPU now has a hw_cpu_id = -1, we IPI CPU
-1... Kaboom!
We are hitting this case regularly on POWER7 machines.
There is also a second race, where the primary will tear down the MMU
mappings before knowing the secondaries have entered real mode.
Also, the secondaries are clearing out any pending IPIs before
guaranteeing that no more will be received.
This changes kexec_prepare_cpus() so that we turn off IRQs in the
primary CPU much earlier. It adds a paca flag to say that the
secondaries have entered the kexec_smp_down() IPI and turned off IRQs,
rather than overloading hw_cpu_id with -1. This new paca flag is
again used to in indicate when the secondaries has entered real mode.
It also ensures that all CPUs have their IRQs off before we clear out
any pending IPI requests (in kexec_cpu_down()) to ensure there are no
trailing IPIs left unacknowledged.
Michael Neuling [Mon, 10 May 2010 20:28:26 +0000 (20:28 +0000)]
powerpc/kexec: Speedup kexec hash PTE tear down
Currently for kexec the PTE tear down on 1TB segment systems normally
requires 3 hcalls for each PTE removal. On a machine with 32GB of
memory it can take around a minute to remove all the PTEs.
This optimises the path so that we only remove PTEs that are valid.
It also uses the read 4 PTEs at once HCALL. For the common case where
a PTEs is invalid in a 1TB segment, this turns the 3 HCALLs per PTE
down to 1 HCALL per 4 PTEs.
This gives an > 10x speedup in kexec times on PHYP, taking a 32GB
machine from around 1 minute down to a few seconds.
Michael Neuling [Mon, 10 May 2010 20:28:26 +0000 (20:28 +0000)]
powerpc/pseries: Add hcall to read 4 ptes at a time in real mode
This adds plpar_pte_read_4_raw() which can be used read 4 PTEs from
PHYP at a time, while in real mode.
It also creates a new hcall9 which can be used in real mode. It's the
same as plpar_hcall9 but minus the tracing hcall statistics which may
require variables outside the RMO.
On large machines we are running out of room below 256MB. In some cases we
only need to ensure the allocation is in the first segment, which may be
256MB or 1TB.
Add slb0_limit and use it to specify the upper limit for the irqstack and
emergency stacks.
On a large ppc64 box, this fixes a panic at boot when the crashkernel=
option is specified (previously we would run out of memory below 256MB).
Anton Blanchard [Mon, 10 May 2010 16:27:38 +0000 (16:27 +0000)]
powerpc/kdump: Use chip->shutdown to disable IRQs
I saw this in a kdump kernel:
IOMMU table initialized, virtual merging enabled
Interrupt 155954 (real) is invalid, disabling it.
Interrupt 155953 (real) is invalid, disabling it.
ie we took some spurious interrupts. default_machine_crash_shutdown tries
to disable all interrupt sources but uses chip->disable which maps to
the default action of:
static void default_disable(unsigned int irq)
{
}
If we use chip->shutdown, then we actually mask the IRQ:
Anton Blanchard [Mon, 10 May 2010 16:25:51 +0000 (16:25 +0000)]
powerpc/kdump: CPUs assume the context of the oopsing CPU
We wrap the crash_shutdown_handles[] calls with longjmp/setjmp, so if any
of them fault we can recover. The problem is we add a hook to the debugger
fault handler hook which calls longjmp unconditionally.
This first part of kdump is run before we marshall the other CPUs, so there
is a very good chance some CPU on the box is going to page fault. And when
it does it hits the longjmp code and assumes the context of the oopsing CPU.
The machine gets very confused when it has 10 CPUs all with the same stack,
all thinking they have the same CPU id. I get even more confused trying
to debug it.
The patch below adds crash_shutdown_cpu and uses it to specify which cpu is
in the protected region. Since it can only be -1 or the oopsing CPU, we don't
need to use memory barriers since it is only valid on the local CPU - no other
CPU will ever see a value that matches it's local CPU id.
Eventually we should switch the order and marshall all CPUs before doing the
crash_shutdown_handles[] calls, but that is a bigger fix.
We called rtas_set_slot_reset while scanning the bus and before the pci_dn
to pcidev mapping has been created. Since we only need the pcidev to work
out the type of reset and that only gets set after the module for the
device loads, lets just do a hot reset if the pcidev is NULL.
Sonny Rao [Mon, 10 May 2010 15:13:41 +0000 (15:13 +0000)]
powerpc/pci: Check devices status property when scanning OF tree
We ran into an issue where it looks like we're not properly ignoring a
pci device with a non-good status property when we walk the device tree
and instanciate the Linux side PCI devices.
However, the EEH init code does look for the property and disables EEH
on these devices. This leaves us in an inconsistent where we are poking
at a supposedly bad piece of hardware and RTAS will block our config
cycles because EEH isn't enabled anyway.
The reason is that decrementer_iSeries_masked is using
LOAD_REG_IMMEDIATE to get the address of a kernel symbol, which
creates relocations that aren't handled by the kernel relocator code.
Instead of reading the tb_ticks_per_jiffy variable, we can just set
the decrementer to its maximum value (0x7fffffff) and that will work
just as well. In fact timer_interrupt sets the decrementer to that
value initially anyway, and we are sure to get into timer_interrupt
once interrupts are reenabled because we store 1 to the decrementer
interrupt flag in the lppaca (LPPACADECRINT(r12) here).
Milton Miller [Wed, 19 May 2010 02:56:29 +0000 (02:56 +0000)]
powerpc: Use common cpu_die (fixes SMP+SUSPEND build)
Configuring a powerpc 32 bit kernel for both SMP and SUSPEND turns on
CPU_HOTPLUG to enable disable_nonboot_cpus to be called by the common
suspend code. Previously the definition of cpu_die for ppc32 was in
the powermac platform code, causing it to be undefined if that platform
as not selected.
arch/powerpc/kernel/built-in.o: In function 'cpu_idle':
arch/powerpc/kernel/idle.c:98: undefined reference to 'cpu_die'
Move the code from setup_64 to smp.c and rename the power mac
versions to their specific names.
Note that this does not setup the cpu_die pointers in either
smp_ops (request a given cpu die) or ppc_md (make this cpu die),
for other platforms but there are generic versions in smp.c.
Andreas Schwab [Tue, 18 May 2010 08:15:21 +0000 (08:15 +0000)]
powerpc: Fix string library functions
The powerpc strncmp implementation does not correctly handle a zero
length, despite the claim in 0119536cd314ef95553604208c25bc35581f7f0a
(Add hand-coded assembly strcmp).
Additionally, all the length arguments are size_t, not int, so use
PPC_LCMPI and eq instead of cmpwi and le throughout.
Michael Ellerman [Wed, 19 May 2010 02:12:32 +0000 (02:12 +0000)]
powerpc/rtasd: Don't start event scan if scan rate is zero
There appear to be Pegasos systems which have the rtas-event-scan
RTAS tokens, but on which the event scan always fails. They also
have an event-scan-rate property containing 0, which means call
event scan 0 times per minute.
So interpret a scan rate of 0 to mean don't scan at all. This fixes
the problem on the Pegasos machines and makes sense as well.
Dave Airlie [Fri, 21 May 2010 05:44:32 +0000 (15:44 +1000)]
Merge remote branch 'nouveau/for-airlied' into drm-next
* nouveau/for-airlied:
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
drm/nv04: Implement missing nv04 PGRAPH methods in software.
drm/nouveau: Use 0x5f instead of 0x9f as imageblit on original NV10.
Jerome Glisse [Wed, 19 May 2010 14:05:50 +0000 (16:05 +0200)]
drm/radeon/kms: record object that have been list reserved
list reservation was too optimistic about ttm object reservation
and could think that an object reserved by some other process
as reserved by the list reservation which was false. Thus when
unreserving the list it might unreserve object that it didn't
reserved in the list. Sorry if it's hard to follow but this
kind of things are just causing headheck.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
USB: remove unused usb_buffer_alloc and usb_buffer_free macros
usb: musb: update gfp/slab.h includes
USB: ftdi_sio: fix legacy SIO-device header
USB: kl5usb105: reimplement using generic framework
USB: kl5usb105: minor clean ups
USB: kl5usb105: fix memory leak
USB: io_ti: use kfifo to implement write buffering
USB: io_ti: remove unsused private counter
USB: ti_usb: use kfifo to implement write buffering
USB: ir-usb: fix incorrect write-buffer length
USB: aircable: fix incorrect write-buffer length
USB: safe_serial: straighten out read processing
USB: safe_serial: reimplement read using generic framework
USB: safe_serial: reimplement write using generic framework
usb-storage: always print quirks
USB: usb-storage: trivial debug improvements
USB: oti6858: use port write fifo
USB: oti6858: use kfifo to implement write buffering
USB: cypress_m8: use kfifo to implement write buffering
USB: cypress_m8: remove unused drain define
...
Fix up conflicts (due to usb_buffer_alloc/free renaming) in
drivers/input/tablet/acecad.c
drivers/input/tablet/kbtab.c
drivers/input/tablet/wacom_sys.c
drivers/media/video/gspca/gspca.c
sound/usb/usbaudio.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Jason Wessel [Fri, 21 May 2010 02:04:31 +0000 (21:04 -0500)]
echi-dbgp: Add kernel debugger support for the usb debug port
This patch adds the capability to use the usb debug port with the
kernel debugger. It is also still possible to use this functionality
with or without the earlyprintk=dbgpX. It is possible to use the
kgdbwait boot argument to debug very early in the kernel start up code.
There are two ways to use this driver extension with a kernel boot argument.
1) kgdbdbgp=# -- Where # is the number of the usb debug controller
You must use sysrq-g to break into the kernel debugger on another
connection type other than the dbgp.
2) kgdbdbgp=#debugControlNum#,#Seconds#
In this mode, the usb debug port is polled every #Seconds# for
character input. It is possible to use gdb or press control-c to
break into the kernel debugger.
From the implementation perspective there are 3 high level changes.
1) Allow variable retries for the the hardware via dbgp_bulk_read().
The amount of retries for the dbgp_bulk_read() needed to be
variable instead of fixed. We do not want to poll at all when the
kernel is operating in interrupt driven mode. The polling only
occurs if the kernel was booted when specifying some number of
seconds via the kgdbdbgp boot argument (IE kgdbdbgp=0,1). In this
case the loop count is reduced to 1 so as introduce the smallest
amount of latency as possible.
2) Save the bulk IN endpoint address for use by the kgdb code.
3) The addition of the kgdb interface code.
This consisted of adding in a character read function for the dbgp
as well as a polling thread to allow the dbgp to interrupt the
kernel execution. The rest is the typical kgdb I/O api.
Jason Wessel [Fri, 21 May 2010 02:04:31 +0000 (21:04 -0500)]
earlyprintk,vga,kdb: Fix \b and \r for earlyprintk=vga with kdb
Allow kdb to work properly with with earlyprintk=vga by interpreting
the backspace and carriage return output characters. These
interpretation of these characters is used for simple line editing
provided in the kdb shell.
Jason Wessel [Fri, 21 May 2010 02:04:30 +0000 (21:04 -0500)]
kgdboc: Add ekgdboc for early use of the kernel debugger
The ekgdboc= differs from kgdboc= in that you can begin debuggin as
soon as the exceptions are setup and the kgdb I/O driver is available,
instead of waiting until the tty subsystem is available.
Jason Wessel [Fri, 21 May 2010 02:04:30 +0000 (21:04 -0500)]
x86,early dr regs,kgdb: Allow kernel debugger early dr register access
If the kernel debugger was configured, attached and started with
kgdbwait, the hardware breakpoint registers should get restored by the
kgdb code which is managing the dr registers.
Jason Wessel [Fri, 21 May 2010 02:04:30 +0000 (21:04 -0500)]
x86,kgdb: Implement early hardware breakpoint debugging
It is not possible to use the hw_breakpoint.c API prior to mm_init(),
but it is possible to use hardware breakpoints with the kernel
debugger.
Prior to smp_init() it is possible to simply write to the dr registers
of the boot cpu directly. This can be used up until the
kgdb_arch_late() is invoked, at which point the standard hw_breakpoint.c
API will get used.
Jason Wessel [Fri, 21 May 2010 02:04:29 +0000 (21:04 -0500)]
x86, kgdb, init: Add early and late debug states
The kernel debugger can operate well before mm_init(), but the x86
hardware breakpoint code which uses the perf api requires that the
kernel allocators are initialized.
This means the kernel debug core needs to provide an optional arch
specific call back to allow the initialization functions to run after
the kernel has been further initialized.
The kdb shell already had a similar restriction with an early
initialization and late initialization. The kdb_init() was moved into
the debug core's version of the late init which is called
dbg_late_init();
Jason Wessel [Fri, 21 May 2010 02:04:27 +0000 (21:04 -0500)]
printk,kdb: capture printk() when in kdb shell
Certain calls from the kdb shell will call out to printk(), and any of
these calls should get vectored back to the kdb_printf() so that the
kdb pager and processing can be used, as well as to properly channel
I/O to the polled I/O devices.
Jason Wessel [Wed, 3 Jun 2009 19:06:57 +0000 (14:06 -0500)]
kgdb: Add the ability to schedule a breakpoint via a tasklet
Some kgdb I/O modules require the ability to create a breakpoint
tasklet, such as kgdboc and external modules such as kgdboe. The
breakpoint tasklet is used as an asynchronous entry point into the
debugger which will have a different function scope than the current
execution path where it might not be safe to have an inline
breakpoint. This is true of some of the kgdb I/O drivers which share
code with kgdb and rest of the kernel users.
Jason Wessel [Fri, 21 May 2010 02:04:26 +0000 (21:04 -0500)]
mips,kgdb: kdb low level trap catch and stack trace
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to have a low level "first opportunity handler" do_trap_or_bp() handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
Also added was a die notification for oops such that kdb can catch an
oops for analysis.
There appeared to be no obvious way to pass the struct pt_regs from
the original exception back to the stack back tracer, so a special
case was added to show_stack() for when kdb is active because you
generally desire to generally look at the back trace of the original
exception.
Jason Wessel [Fri, 21 May 2010 02:04:25 +0000 (21:04 -0500)]
powerpc,kgdb: Introduce low level trap catching
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to allow the kernel debugger to handle the exception first in
program_check_exception().
The other change here is to make sure that kgdb_handle_exception() is
called with correct parameters when catching an oops, because kdb
needs to know if the entry was an oops, single step, or breakpoint
exception.
Jason Wessel [Fri, 21 May 2010 02:04:25 +0000 (21:04 -0500)]
x86,kgdb: Add low level debug hook
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a triple fault is
to have a low level "first opportunity handler" in the int3 exception
handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
Jason Wessel [Mon, 27 Apr 2009 15:58:06 +0000 (10:58 -0500)]
kgdb: remove post_primary_code references
Remove all the references to the kgdb_post_primary_code. This
function serves no useful purpose because you can obtain the same
information from the "struct kgdb_state *ks" from with in the
debugger, if for some reason you want the data.
Also remove the unintentional duplicate assignment for ks->ex_vector.
Jason Wessel [Fri, 21 May 2010 02:04:24 +0000 (21:04 -0500)]
kgdboc,keyboard: Keyboard driver for kdb with kgdb
This patch adds in the kdb PS/2 keyboard driver. This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.
This patch also enables early kdb debug via kgdbwait and the keyboard.
All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.
If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:
kgdboc=kbd kgdbwait
If you wanted serial and or the keyboard access you could use:
kgdboc=kbd,ttyS0
You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.
Turn it on:
echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc
Turn it off:
echo "" > /sys/module/kgdboc/parameters/kgdboc
Jason Wessel [Fri, 21 May 2010 02:04:24 +0000 (21:04 -0500)]
kgdb: gdb "monitor" -> kdb passthrough
One of the driving forces behind integrating another front end (kdb)
to the debug core is to allow front end commands to be accessible via
gdb's monitor command. It is true that you could write gdb macros to
get certain data, but you may want to just use gdb to access the
commands that are available in the kdb front end.
This patch implements the Rcmd gdb stub packet. In gdb you access
this with the "monitor" command. For instance you could type "monitor
help", "monitor lsmod" or "monitor ps A" etc...
There is no error checking or command restrictions on what you can and
cannot access at this point. Doing something like trying to set
breakpoints with the monitor command is going to cause nothing but
problems. Perhaps in the future only the commands that are actually
known to work with the gdb monitor command will be available.
Jason Wessel [Fri, 21 May 2010 02:04:22 +0000 (21:04 -0500)]
kgdb,8250,pl011: Return immediately from console poll
The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available. This is required in order to get the
page scrolling mechanism working.
Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.
NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.
Jason Wessel [Fri, 21 May 2010 02:04:21 +0000 (21:04 -0500)]
kgdb: core changes to support kdb
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
Jason Wessel [Fri, 21 May 2010 02:04:21 +0000 (21:04 -0500)]
kdb: core for kgdb back end (2 of 2)
This patch contains the hooks and instrumentation into kernel which
live outside the kernel/debug directory, which the kdb core
will call to run commands like lsmod, dmesg, bt etc...
Jason Wessel [Fri, 21 May 2010 02:04:20 +0000 (21:04 -0500)]
kdb: core for kgdb back end (1 of 2)
This patch contains only the kdb core. Because the change set was
large, it was split. The next patch in the series includes the
instrumentation into the core kernel which are mainly helper functions
for kdb.
This work is directly derived from kdb v4.4 found at:
ftp://oss.sgi.com/projects/kdb/download/v4.4/
The kdb internals have been re-organized to make them mostly platform
independent and to connect everything to the debug core which is used by
gdbstub (which has long been known as kgdb).
The original version of kdb was 58,000 lines worth of changes to
support x86. From that implementation only the kdb shell, and basic
commands for memory access, runcontrol, lsmod, and dmesg where carried
forward.
This is a generic implementation which aims to cover all the current
architectures using the kgdb core: ppc, arm, x86, mips, sparc, sh and
blackfin. More archictectures can be added by implementing the
architecture specific kgdb functions.
Jason Wessel [Fri, 21 May 2010 02:04:20 +0000 (21:04 -0500)]
kgdb,sh: update superh kgdb exception handling
Implement kgdb_arch_pc() which adjusts the pc if it needs to be
adjusted after a software breakpoint trap.
Implement kgdb_arch_set_pc() which is a new required function in the
kgdb debug core.
When processing a single step return zero in the error exception field
so that the debug core can distinguish between a single step trap and
a breakpoint trap generically.
Jason Wessel [Fri, 2 Apr 2010 16:48:03 +0000 (11:48 -0500)]
Separate the gdbstub from the debug core
Split the former kernel/kgdb.c into debug_core.c which contains the
kernel debugger exception logic and to the gdbstub.c which contains
the logic for allowing gdb to talk to the debug core.
This also created a private include file called debug_core.h which
contains all the definitions to glue the debug_core to any other
debugger connections.
projects / linux.git / log