Shalom Toledo [Fri, 2 Nov 2018 19:49:15 +0000 (19:49 +0000)]
mlxsw: spectrum: Fix IP2ME CPU policer configuration
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73ce ("mlxsw: spectrum: Add policers for trap groups") Signed-off-by: Shalom Toledo <[email protected]> Signed-off-by: Ido Schimmel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Arnd Bergmann [Fri, 2 Nov 2018 15:36:24 +0000 (16:36 +0100)]
qed: fix link config error handling
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7aa ("qed: Add supported link and advertise link to display in ethtool.") Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Linus Torvalds [Sun, 4 Nov 2018 01:37:09 +0000 (18:37 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A memory (under-)allocation fix and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Fix off by one bug
sched/rt: Update comment in pick_next_task_rt()
Linus Torvalds [Sun, 4 Nov 2018 01:25:17 +0000 (18:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Linus Torvalds [Sun, 4 Nov 2018 01:13:43 +0000 (18:13 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates and fixes from Ingo Molnar:
"These are almost all tooling updates: 'perf top', 'perf trace' and
'perf script' fixes and updates, an UAPI header sync with the merge
window versions, license marker updates, much improved Sparc support
from David Miller, and a number of fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
perf intel-pt/bts: Calculate cpumode for synthesized samples
perf intel-pt: Insert callchain context into synthesized callchains
perf tools: Don't clone maps from parent when synthesizing forks
perf top: Start display thread earlier
tools headers uapi: Update linux/if_link.h header copy
tools headers uapi: Update linux/netlink.h header copy
tools headers: Sync the various kvm.h header copies
tools include uapi: Update linux/mmap.h copy
perf trace beauty: Use the mmap flags table generated from headers
perf beauty: Wire up the mmap flags table generator to the Makefile
perf beauty: Add a generator for MAP_ mmap's flag constants
tools include uapi: Update asound.h copy
tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
tools include uapi: Update linux/fs.h copy
perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
perf cs-etm: Correct CPU mode for samples
perf unwind: Take pgoff into account when reporting elf to libdwfl
perf top: Do not use overwrite mode by default
perf top: Allow disabling the overwrite mode
perf trace: Beautify mount's first pathname arg
...
Linus Torvalds [Sun, 4 Nov 2018 01:12:09 +0000 (18:12 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
sched/core: Take the hotplug lock in sched_init_smp()
When running on linux-next (8c60c36d0b8c ("Add linux-next specific files
for 20181019")) + CONFIG_PROVE_LOCKING=y on a big.LITTLE system (e.g.
Juno or HiKey960), we get the following report:
The static_key in question is 'sched_asym_cpucapacity' introduced by
commit:
df054e8445a4 ("sched/topology: Add static_key for asymmetric CPU capacity optimizations")
In this particular case, we enable it because smp_prepare_cpus() will
end up fetching the capacity-dmips-mhz entry from the devicetree,
so we already have some asymmetry detected when entering sched_init_smp().
This didn't get detected in tip/sched/core because we were missing:
commit cb538267ea1e ("jump_label/lockdep: Assert we hold the hotplug lock for _cpuslocked() operations")
Calls to build_sched_domains() post sched_init_smp() will hold the
hotplug lock, it just so happens that this very first call is a
special case. As stated by a comment in sched_init_smp(), "There's no
userspace yet to cause hotplug operations" so this is a harmless
warning.
However, to both respect the semantics of underlying
callees and make lockdep happy, take the hotplug lock in
sched_init_smp(). This also satisfies the comment atop
sched_init_domains() that says "Callers must hold the hotplug lock".
Yunsheng Lin [Fri, 2 Nov 2018 09:47:48 +0000 (17:47 +0800)]
net: hns3: Fix for out-of-bounds access when setting pfc back pressure
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4b9 ("net: hns3: Fixes the back pressure setting when sriov is enabled") Signed-off-by: Yunsheng Lin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David S. Miller [Sat, 3 Nov 2018 22:40:01 +0000 (15:40 -0700)]
Merge branch 'net-bql-better-deal-with-GSO'
Eric Dumazet says:
====================
net: bql: better deal with GSO
While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.
On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.
This patch series :
- Add __netdev_tx_sent_queue() so that drivers
can implement efficient BQL and xmit_more support.
- Implement a work around in dev_hard_start_xmit()
for drivers not using __netdev_tx_sent_queue()
- changes mlx4 to use __netdev_tx_sent_queue()
v2: Tariq and Willem feedback addressed.
added __netdev_tx_sent_queue() (Willem suggestion)
====================
Eric Dumazet [Wed, 31 Oct 2018 15:39:13 +0000 (08:39 -0700)]
net: do not abort bulk send on BQL status
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Eric Dumazet [Wed, 31 Oct 2018 15:39:12 +0000 (08:39 -0700)]
net: bql: add __netdev_tx_sent_queue()
When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.
Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.
BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.
But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.
Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.
Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.
Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.
Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.
Code template in a driver might look like the following :
Vasily Averin [Sat, 3 Nov 2018 20:13:17 +0000 (16:13 -0400)]
ext4: avoid potential extra brelse in setup_new_flex_group_blocks()
Currently bh is set to NULL only during first iteration of for cycle,
then this pointer is not cleared after end of using.
Therefore rollback after errors can lead to extra brelse(bh) call,
decrements bh counter and later trigger an unexpected warning in __brelse()
Patch moves brelse() calls in body of cycle to exclude requirement of
brelse() call in rollback.
Linus Torvalds [Sat, 3 Nov 2018 17:55:23 +0000 (10:55 -0700)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kprobe: make page to RO mode when allocate it
arm64: kdump: fix small typo
arm64: makefile fix build of .i file in external module case
Linus Torvalds [Sat, 3 Nov 2018 17:45:55 +0000 (10:45 -0700)]
Merge tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes and updates from Steve French:
"Three small fixes (one Kerberos related, one for stable, and another
fixes an oops in xfstest 377), two helpful debugging improvements,
three patches for cifs directio and some minor cleanup"
* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix signed/unsigned mismatch on aio_read patch
cifs: don't dereference smb_file_target before null check
CIFS: Add direct I/O functions to file_operations
CIFS: Add support for direct I/O write
CIFS: Add support for direct I/O read
smb3: missing defines and structs for reparse point handling
smb3: allow more detailed protocol info on open files for debugging
smb3: on kerberos mount if server doesn't specify auth type use krb5
smb3: add trace point for tree connection
cifs: fix spelling mistake, EACCESS -> EACCES
cifs: fix return value for cifs_listxattr
David S. Miller [Sat, 3 Nov 2018 17:44:06 +0000 (10:44 -0700)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-11-02
please apply one round of qeth fixes for -net.
Patch 1 is rather large and removes a use-after-free hazard from many of our
debug trace entries.
Patch 2 is yet another fix-up for the L3 subdriver's new IP address management
code.
Patch 3 and 4 resolve some fallout from the recent changes wrt how/when qeth
allocates its net_device.
Patch 5 makes sure we don't set reserved bits when building HW commands from
user-provided data.
And finally, patch 6 allows ethtool to play nice with new HW.
====================
Julian Wiedmann [Fri, 2 Nov 2018 18:04:12 +0000 (19:04 +0100)]
s390/qeth: sanitize ARP requests
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.
This also sets the correct command length for ARP_REMOVE_ENTRY.
Julian Wiedmann [Fri, 2 Nov 2018 18:04:11 +0000 (19:04 +0100)]
s390/qeth: fix initial operstate
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e3d ("s390/qeth: remove duplicated carrier state tracking") Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:10 +0000 (19:04 +0100)]
s390/qeth: unregister netdevice only when registered
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e89f ("s390/qeth: allocate netdevice early") Reported-by: Karsten Graul <[email protected]> Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:09 +0000 (19:04 +0100)]
s390/qeth: fix HiperSockets sniffer
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Julian Wiedmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Julian Wiedmann [Fri, 2 Nov 2018 18:04:08 +0000 (19:04 +0100)]
s390/qeth: sanitize strings in debug messages
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Linus Torvalds [Sat, 3 Nov 2018 17:35:52 +0000 (10:35 -0700)]
Merge branch 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull 9p fix from Al Viro:
"Regression fix for net/9p handling of iov_iter; broken by braino when
switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: Fix 9p virtio breakage
Linus Torvalds [Sat, 3 Nov 2018 17:34:03 +0000 (10:34 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mvsas: Remove set but not used variable 'id'
scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
scsi: qla2xxx: Remove a set-but-not-used variable
scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
scsi: qla2xxx: Declare local functions 'static'
scsi: qla2xxx: Improve several kernel-doc headers
scsi: qla2xxx: Modify fall-through annotations
scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
scsi: mvsas: Use dma_pool_zalloc
scsi: target: Don't request modules that aren't even built
scsi: target: Set response length for REPORT TARGET PORT GROUPS
Linus Torvalds [Sat, 3 Nov 2018 17:21:43 +0000 (10:21 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:
- more ocfs2 work
- various leftovers
* emailed patches from Andrew Morton <[email protected]>:
memory_hotplug: cond_resched in __remove_pages
bfs: add sanity check at bfs_fill_super()
kernel/sysctl.c: remove duplicated include
kernel/kexec_file.c: remove some duplicated includes
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2: dlmglue: clean up timestamp handling
ocfs2: don't put and assigning null to bh allocated outside
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
ocfs2: don't use iocb when EIOCBQUEUED returns
ocfs2: without quota support, avoid calling quota recovery
ocfs2: remove ocfs2_is_o2cb_active()
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
include/linux/notifier.h: SRCU: fix ctags
mm: handle no memcg case in memcg_kmem_charge() properly
It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large. Fix the issue by calling
cond_resched once per memory section.
Tetsuo Handa [Fri, 2 Nov 2018 22:48:42 +0000 (15:48 -0700)]
bfs: add sanity check at bfs_fill_super()
syzbot is reporting too large memory allocation at bfs_fill_super() [1].
Since file system image is corrupted such that bfs_sb->s_start == 0,
bfs_fill_super() is trying to allocate 8MB of continuous memory. Fix
this by adding a sanity check on bfs_sb->s_start, __GFP_NOWARN and
printf().
Michal Hocko [Fri, 2 Nov 2018 22:48:31 +0000 (15:48 -0700)]
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
THP allocation mode is quite complex and it depends on the defrag mode.
This complexity is hidden in alloc_hugepage_direct_gfpmask from a large
part currently. The NUMA special casing (namely __GFP_THISNODE) is
however independent and placed in alloc_pages_vma currently. This both
adds an unnecessary branch to all vma based page allocation requests and
it makes the code more complex unnecessarily as well. Not to mention
that e.g. shmem THP used to do the node reclaiming unconditionally
regardless of the defrag mode until recently. This was not only
unexpected behavior but it was also hardly a good default behavior and I
strongly suspect it was just a side effect of the code sharing more than
a deliberate decision which suggests that such a layering is wrong.
Get rid of the thp special casing from alloc_pages_vma and move the
logic to alloc_hugepage_direct_gfpmask. __GFP_THISNODE is applied to the
resulting gfp mask only when the direct reclaim is not requested and
when there is no explicit numa binding to preserve the current logic.
Please note that there's also a slight difference wrt MPOL_BIND now. The
previous code would avoid using __GFP_THISNODE if the local node was
outside of policy_nodemask(). After this patch __GFP_THISNODE is avoided
for all MPOL_BIND policies. So there's a difference that if local node
is actually allowed by the bind policy's nodemask, previously
__GFP_THISNODE would be added, but now it won't be. From the behavior
POV this is still correct because the policy nodemask is used.
Larry Chen [Fri, 2 Nov 2018 22:48:27 +0000 (15:48 -0700)]
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2_defrag_extent() might leak allocated clusters. When the file
system has insufficient space, the number of claimed clusters might be
less than the caller wants. If that happens, the original code might
directly commit the transaction without returning clusters.
This patch is based on code in ocfs2_add_clusters_in_btree().
Arnd Bergmann [Fri, 2 Nov 2018 22:48:23 +0000 (15:48 -0700)]
ocfs2: dlmglue: clean up timestamp handling
The handling of timestamps outside of the 1970..2038 range in the dlm
glue is rather inconsistent: on 32-bit architectures, this has always
wrapped around to negative timestamps in the 1902..1969 range, while on
64-bit kernels all timestamps are interpreted as positive 34 bit numbers
in the 1970..2514 year range.
Now that the VFS code handles 64-bit timestamps on all architectures, we
can make the behavior more consistent here, and return the same result
that we had on 64-bit already, making the file system y2038 safe in the
process. Outside of dlmglue, it already uses 64-bit on-disk timestamps
anway, so that part is fine.
For consistency, I'm changing ocfs2_pack_timespec() to clamp anything
outside of the supported range to the minimum and maximum values. This
avoids a possible ambiguity of values before 1970 in particular, which
used to be interpreted as times at the end of the 2514 range previously.
Changwei Ge [Fri, 2 Nov 2018 22:48:19 +0000 (15:48 -0700)]
ocfs2: don't put and assigning null to bh allocated outside
ocfs2_read_blocks() and ocfs2_read_blocks_sync() are both used to read
several blocks from disk. Currently, the input argument *bhs* can be
NULL or NOT. It depends on the caller's behavior. If the function
fails in reading blocks from disk, the corresponding bh will be assigned
to NULL and put.
Obviously, above process for non-NULL input bh is not appropriate.
Because the caller doesn't even know its bhs are put and re-assigned.
If buffer head is managed by caller, ocfs2_read_blocks and
ocfs2_read_blocks_sync() should not evaluate it to NULL. It will cause
caller accessing illegal memory, thus crash.
Changwei Ge [Fri, 2 Nov 2018 22:48:15 +0000 (15:48 -0700)]
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
Somehow, file system metadata was corrupted, which causes
ocfs2_check_dir_entry() to fail in function ocfs2_dir_foreach_blk_el().
According to the original design intention, if above happens we should
skip the problematic block and continue to retrieve dir entry. But
there is obviouse misuse of brelse around related code.
After failure of ocfs2_check_dir_entry(), current code just moves to
next position and uses the problematic buffer head again and again
during which the problematic buffer head is released for multiple times.
I suppose, this a serious issue which is long-lived in ocfs2. This may
cause other file systems which is also used in a the same host insane.
So we should also consider about bakcporting this patch into linux
-stable.
Changwei Ge [Fri, 2 Nov 2018 22:48:11 +0000 (15:48 -0700)]
ocfs2: don't use iocb when EIOCBQUEUED returns
When -EIOCBQUEUED returns, it means that aio_complete() will be called
from dio_complete(), which is an asynchronous progress against
write_iter. Generally, IO is a very slow progress than executing
instruction, but we still can't take the risk to access a freed iocb.
And we do face a BUG crash issue. Using the crash tool, iocb is
obviously freed already.
And the backtrace shows:
ocfs2_file_write_iter+0xcaa/0xd00 [ocfs2]
aio_run_iocb+0x229/0x2f0
do_io_submit+0x291/0x540
SyS_io_submit+0x10/0x20
system_call_fastpath+0x16/0x75
Guozhonghua [Fri, 2 Nov 2018 22:48:07 +0000 (15:48 -0700)]
ocfs2: without quota support, avoid calling quota recovery
During one dead node's recovery by other node, quota recovery work will
be queued. We should avoid calling quota when it is not supported, so
check the quota flags.
Gang He [Fri, 2 Nov 2018 22:48:03 +0000 (15:48 -0700)]
ocfs2: remove ocfs2_is_o2cb_active()
Remove ocfs2_is_o2cb_active(). We have similar functions to identify
which cluster stack is being used via osb->osb_cluster_stack.
Secondly, the current implementation of ocfs2_is_o2cb_active() is not
totally safe. Based on the design of stackglue, we need to get
ocfs2_stack_lock before using ocfs2_stack related data structures, and
that active_stack pointer can be NULL in the case of mount failure.
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
THP allocation might be really disruptive when allocated on NUMA system
with the local node full or hard to reclaim. Stefan has posted an
allocation stall report on 4.12 based SLES kernel which suggests the
same issue:
The defrag mode is "madvise" and from the above report it is clear that
the THP has been allocated for MADV_HUGEPAGA vma.
Andrea has identified that the main source of the problem is
__GFP_THISNODE usage:
: The problem is that direct compaction combined with the NUMA
: __GFP_THISNODE logic in mempolicy.c is telling reclaim to swap very
: hard the local node, instead of failing the allocation if there's no
: THP available in the local node.
:
: Such logic was ok until __GFP_THISNODE was added to the THP allocation
: path even with MPOL_DEFAULT.
:
: The idea behind the __GFP_THISNODE addition, is that it is better to
: provide local memory in PAGE_SIZE units than to use remote NUMA THP
: backed memory. That largely depends on the remote latency though, on
: threadrippers for example the overhead is relatively low in my
: experience.
:
: The combination of __GFP_THISNODE and __GFP_DIRECT_RECLAIM results in
: extremely slow qemu startup with vfio, if the VM is larger than the
: size of one host NUMA node. This is because it will try very hard to
: unsuccessfully swapout get_user_pages pinned pages as result of the
: __GFP_THISNODE being set, instead of falling back to PAGE_SIZE
: allocations and instead of trying to allocate THP on other nodes (it
: would be even worse without vfio type1 GUP pins of course, except it'd
: be swapping heavily instead).
Fix this by removing __GFP_THISNODE for THP requests which are
requesting the direct reclaim. This effectivelly reverts 5265047ac301
on the grounds that the zone/node reclaim was known to be disruptive due
to premature reclaim when there was memory free. While it made sense at
the time for HPC workloads without NUMA awareness on rare machines, it
was ultimately harmful in the majority of cases. The existing behaviour
is similar, if not as widespare as it applies to a corner case but
crucially, it cannot be tuned around like zone_reclaim_mode can. The
default behaviour should always be to cause the least harm for the
common case.
If there are specialised use cases out there that want zone_reclaim_mode
in specific cases, then it can be built on top. Longterm we should
consider a memory policy which allows for the node reclaim like behavior
for the specific memory ranges which would allow a
: Both patches look correct to me but I'm responding to this one because
: it's the fix. The change makes sense and moves further away from the
: severe stalling behaviour we used to see with both THP and zone reclaim
: mode.
:
: I put together a basic experiment with usemem configured to reference a
: buffer multiple times that is 80% the size of main memory on a 2-socket
: box with symmetric node sizes and defrag set to "always". The defrag
: setting is not the default but it would be functionally similar to
: accessing a buffer with madvise(MADV_HUGEPAGE). Usemem is configured to
: reference the buffer multiple times and while it's not an interesting
: workload, it would be expected to complete reasonably quickly as it fits
: within memory. The results were;
:
: usemem
: vanilla noreclaim-v1
: Amean Elapsd-1 42.78 ( 0.00%) 26.87 ( 37.18%)
: Amean Elapsd-3 27.55 ( 0.00%) 7.44 ( 73.00%)
: Amean Elapsd-4 5.72 ( 0.00%) 5.69 ( 0.45%)
:
: This shows the elapsed time in seconds for 1 thread, 3 threads and 4
: threads referencing buffers 80% the size of memory. With the patches
: applied, it's 37.18% faster for the single thread and 73% faster with two
: threads. Note that 4 threads showing little difference does not indicate
: the problem is related to thread counts. It's simply the case that 4
: threads gets spread so their workload mostly fits in one node.
:
: The overall view from /proc/vmstats is more startling
:
: 4.19.0-rc1 4.19.0-rc1
: vanillanoreclaim-v1r1
: Minor Faults 35593425 708164
: Major Faults 484088 36
: Swap Ins 3772837 0
: Swap Outs 3932295 0
:
: Massive amounts of swap in/out without the patch
:
: Direct pages scanned 6013214 0
: Kswapd pages scanned 0 0
: Kswapd pages reclaimed 0 0
: Direct pages reclaimed 4033009 0
:
: Lots of reclaim activity without the patch
:
: Kswapd efficiency 100% 100%
: Kswapd velocity 0.000 0.000
: Direct efficiency 67% 100%
: Direct velocity 11191.956 0.000
:
: Mostly from direct reclaim context as you'd expect without the patch.
:
: Page writes by reclaim 3932314.000 0.000
: Page writes file 19 0
: Page writes anon 3932295 0
: Page reclaim immediate 42336 0
:
: Writes from reclaim context is never good but the patch eliminates it.
:
: We should never have default behaviour to thrash the system for such a
: basic workload. If zone reclaim mode behaviour is ever desired but on a
: single task instead of a global basis then the sensible option is to build
: a mempolicy that enforces that behaviour.
This was a severe regression compared to previous kernels that made
important workloads unusable and it starts when __GFP_THISNODE was
added to THP allocations under MADV_HUGEPAGE. It is not a significant
risk to go to the previous behavior before __GFP_THISNODE was added, it
worked like that for years.
This was simply an optimization to some lucky workloads that can fit in
a single node, but it ended up breaking the VM for others that can't
possibly fit in a single node, so going back is safe.
Roman Gushchin [Fri, 2 Nov 2018 22:47:49 +0000 (15:47 -0700)]
mm: handle no memcg case in memcg_kmem_charge() properly
Mike Galbraith reported a regression caused by the commit 9b6f7e163cd0
("mm: rework memcg kernel stack accounting") on a system with
"cgroup_disable=memory" boot option: the system panics with the following
stack trace:
The problem occurs because get_mem_cgroup_from_current() returns the NULL
pointer if memory controller is disabled. Let's check if this is a case
at the beginning of memcg_kmem_charge() and just return 0 if
mem_cgroup_disabled() returns true. This is how we handle this case in
many other places in the memory controller code.
netfilter: conntrack: fix calculation of next bucket number in early_drop
If there's no entry to drop in bucket that corresponds to the hash,
early_drop() should look for it in other buckets. But since it increments
hash instead of bucket number, it actually looks in the same bucket 8
times: hsize is 16k by default (14 bits) and hash is 32-bit value, so
reciprocal_scale(hash, hsize) returns the same value for hash..hash+7 in
most cases.
Fix it by increasing bucket number instead of hash and rename _hash
to bucket to avoid future confusion.
netfilter: nft_compat: ebtables 'nat' table is normal chain type
Unlike ip(6)tables, the ebtables nat table has no special properties.
This bug causes 'ebtables -A' to fail when using a target such as
'snat' (ebt_snat target sets ".table = "nat"'). Targets that have
no table restrictions work fine.
netfilter: nfnetlink_cttimeout: pass default timeout policy to obj_to_nlattr
Otherwise, we hit a NULL pointer deference since handlers always assume
default timeout policy is passed.
netlink: 24 bytes leftover after parsing attributes in process `syz-executor2'.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 9575 Comm: syz-executor1 Not tainted 4.19.0+ #312
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:icmp_timeout_obj_to_nlattr+0x77/0x170 net/netfilter/nf_conntrack_proto_icmp.c:297
Fixes: c779e849608a ("netfilter: conntrack: remove get_timeout() indirection") Reported-by: Eric Dumazet <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
Jozsef Kadlecsik [Tue, 30 Oct 2018 21:43:42 +0000 (22:43 +0100)]
netfilter: ipset: Fix calling ip_set() macro at dumping
The ip_set() macro is called when either ip_set_ref_lock held only
or no lock/nfnl mutex is held at dumping. Take this into account
properly. Also, use Pablo's suggestion to use rcu_dereference_raw(),
the ref_netlink protects the set.
When IDLETIMER rule is added, sysfs file is created under
/sys/class/xt_idletimer/timers/
But some label name shouldn't be used.
".", "..", "power", "uevent", "subsystem", etc...
So that sysfs filename checking routine is needed.
perf trace: Fix setting of augmented payload when using eBPF + raw_syscalls
For now with BPF raw_augmented we hook into raw_syscalls:sys_enter and
there we get all 6 syscall args plus the tracepoint common fields
(sizeof(long)) and the syscall_nr (another long). So we check if that is
the case and if so don't look after the sc->args_size, but always after
the full raw_syscalls:sys_enter payload, which is fixed.
We'll revisit this later to pass s->args_size to the BPF augmenter (now
tools/perf/examples/bpf/augmented_raw_syscalls.c, so that it copies only
what we need for each syscall, like what happens when we use
syscalls:sys_enter_NAME, so that we reduce the kernel/userspace traffic
to just what is needed for each syscall.
====================
net: timeout fixes for GENET and SYSTEMPORT
This patch series fixes occasional transmit timeout around the time
the system goes into suspend. GENET and SYSTEMPORT have nearly the same
logic in that regard and were both affected in the same way.
Please queue up for stable, thanks!
====================
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce17 ("net: systemport: add suspend and resume support") Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Doug Berger [Thu, 1 Nov 2018 22:55:37 +0000 (15:55 -0700)]
net: bcmgenet: protect stop from timeout
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcmgenet_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcmgenet_netif_stop. There
are currently only two users of the bcmgenet_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcmgenet_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcmgenet_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcmgenet_netif_start so it is moved into the driver open service.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <[email protected]> Signed-off-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
David Howells [Thu, 1 Nov 2018 13:39:53 +0000 (13:39 +0000)]
rxrpc: Fix lockup due to no error backoff after ack transmit error
If the network becomes (partially) unavailable, say by disabling IPv6, the
background ACK transmission routine can get itself into a tizzy by
proposing immediate ACK retransmission. Since we're in the call event
processor, that happens immediately without returning to the workqueue
manager.
The condition should clear after a while when either the network comes back
or the call times out.
Fix this by:
(1) When re-proposing an ACK on failed Tx, don't schedule it immediately.
This will allow a certain amount of time to elapse before we try
again.
(2) Enforce a return to the workqueue manager after a certain number of
iterations of the call processing loop.
(3) Add a backoff delay that increases the delay on deferred ACKs by a
jiffy per failed transmission to a limit of HZ. The backoff delay is
cleared on a successful return from kernel_sendmsg().
(4) Cancel calls immediately if the opening sendmsg fails. The layer
above can arrange retransmission or rotate to another server.
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code") Signed-off-by: David Howells <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Jeff Barnhill [Fri, 2 Nov 2018 20:23:57 +0000 (20:23 +0000)]
net/ipv6: Add anycast addresses to a global hashtable
icmp6_send() function is expensive on systems with a large number of
interfaces. Every time it’s called, it has to verify that the source
address does not correspond to an existing anycast address by looping
through every device and every anycast address on the device. This can
result in significant delays for a CPU when there are a large number of
neighbors and ND timers are frequently timing out and calling
neigh_invalidate().
Add anycast addresses to a global hashtable to allow quick searching for
matching anycast addresses. This is based on inet6_addr_lst in addrconf.c.
Frieder Schrempf [Wed, 31 Oct 2018 21:52:19 +0000 (22:52 +0100)]
usbnet: smsc95xx: disable carrier check while suspending
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation") Signed-off-by: Frieder Schrempf <[email protected]> Reviewed-by: Raghuram Chary J <[email protected]> Signed-off-by: David S. Miller <[email protected]>
ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
Remove unused parameter from HASH1 dmas property on stm32mp157c SoC.
Fixes: 1e726a40e067 ("ARM: dts: stm32: Add HASH support on stm32mp157c") Signed-off-by: Alexandre Torgue <[email protected]>
[Olof: Bug doesn't cause any harm, so shouldn't need stable backport] Signed-off-by: Olof Johansson <[email protected]>
Arnd Bergmann [Fri, 5 Oct 2018 16:15:49 +0000 (18:15 +0200)]
ARM: orion: avoid VLA in orion_mpp_conf
Testing randconfig builds found an instance of a VLA that was
missed when determining that we have removed them all:
arch/arm/plat-orion/mpp.c: In function 'orion_mpp_conf':
arch/arm/plat-orion/mpp.c:31:2: error: ISO C90 forbids variable length array 'mpp_ctrl' [-Werror=vla]
This one is fairly straightforward: we know what all three
callers are, and the maximum length is not very long.
Daniel Borkmann [Fri, 2 Nov 2018 10:35:46 +0000 (11:35 +0100)]
bpf: fix bpf_prog_get_info_by_fd to return 0 func_lens for unpriv
While dbecd7388476 ("bpf: get kernel symbol addresses via syscall")
zeroed info.nr_jited_ksyms in bpf_prog_get_info_by_fd() for queries
from unprivileged users, commit 815581c11cc2 ("bpf: get JITed image
lengths of functions via syscall") forgot about doing so and therefore
returns the #elems of the user set up buffer which is incorrect. It
also needs to indicate a info.nr_jited_func_lens of zero.
Daniel Borkmann [Fri, 2 Nov 2018 20:39:02 +0000 (21:39 +0100)]
Merge branch 'bpf-accurate-prog-addr'
Song Liu says:
====================
Changes v1 -> v2:
1. Added main program length to bpf_prog_info->jited_fun_lens (3/3).
2. Updated commit message of 1/3 and 2/3 with more background about the
address masking, and why it is still save after the changes.
3. Replace "ulong" with "unsigned long".
This set improves bpf program address showed in /proc/kallsyms and in
bpf_prog_info. First, real program address is showed instead of page
address. Second, when there is no subprogram, bpf_prog_info->jited_ksyms
and bpf_prog_info->jited_fun_lens returns the main prog address and
length.
====================
Song Liu [Fri, 2 Nov 2018 17:16:17 +0000 (10:16 -0700)]
bpf: show main program address and length in bpf_prog_info
Currently, when there is no subprog (prog->aux->func_cnt == 0),
bpf_prog_info does not return any jited_ksyms or jited_func_lens. This
patch adds main program address (prog->bpf_func) and main program
length (prog->jited_len) to bpf_prog_info.
Song Liu [Fri, 2 Nov 2018 17:16:16 +0000 (10:16 -0700)]
bpf: show real jited address in bpf_prog_info->jited_ksyms
Currently, jited_ksyms in bpf_prog_info shows page addresses of jited
bpf program. The main reason here is to not expose randomized start
address. However, this is not ideal for detailed profiling (find hot
instructions from stack traces). This patch replaces the page address
with real prog start address.
This change is OK because bpf_prog_get_info_by_fd() is only available
to root.
Song Liu [Fri, 2 Nov 2018 17:16:15 +0000 (10:16 -0700)]
bpf: show real jited prog address in /proc/kallsyms
Currently, /proc/kallsyms shows page address of jited bpf program. The
main reason here is to not expose randomized start address. However,
This is not ideal for detailed profiling (find hot instructions from
stack traces). This patch replaces the page address with real prog start
address.
This change is OK because these addresses are still protected by sysctl
kptr_restrict (see kallsyms_show_value()), and only programs loaded by
root are added to kallsyms (see bpf_prog_kallsyms_add()).
Steve French [Thu, 1 Nov 2018 15:54:32 +0000 (10:54 -0500)]
cifs: fix signed/unsigned mismatch on aio_read patch
The patch "CIFS: Add support for direct I/O read" had
a signed/unsigned mismatch (ssize_t vs. size_t) in the
return from one function. Similar trivial change
in aio_write
Colin Ian King [Thu, 1 Nov 2018 13:14:30 +0000 (13:14 +0000)]
cifs: don't dereference smb_file_target before null check
There is a null check on dst_file->private data which suggests
it can be potentially null. However, before this check, pointer
smb_file_target is derived from dst_file->private and dereferenced
in the call to tlink_tcon, hence there is a potential null pointer
deference.
Fix this by assigning smb_file_target and target_tcon after the
null pointer sanity checks.
Detected by CoverityScan, CID#1475302 ("Dereference before null check")
Fixes: 04b38d601239 ("vfs: pull btrfs clone API to vfs layer") Signed-off-by: Colin Ian King <[email protected]> Signed-off-by: Steve French <[email protected]>
Long Li [Wed, 31 Oct 2018 22:13:11 +0000 (22:13 +0000)]
CIFS: Add direct I/O functions to file_operations
With direct read/write functions implemented, add them to file_operations.
Dircet I/O is used under two conditions:
1. When mounting with "cache=none", CIFS uses direct I/O for all user file
data transfer.
2. When opening a file with O_DIRECT, CIFS uses direct I/O for all data
transfer on this file.
Steve French [Wed, 31 Oct 2018 00:50:31 +0000 (19:50 -0500)]
smb3: allow more detailed protocol info on open files for debugging
In order to debug complex problems it is often helpful to
have detailed information on the client and server view
of the open file information. Add the ability for root to
view the list of smb3 open files and dump the persistent
handle and other info so that it can be more easily
correlated with server logs.
Steve French [Sun, 28 Oct 2018 18:13:23 +0000 (13:13 -0500)]
smb3: on kerberos mount if server doesn't specify auth type use krb5
Some servers (e.g. Azure) do not include a spnego blob in the SMB3
negotiate protocol response, so on kerberos mounts ("sec=krb5")
we can fail, as we expected the server to list its supported
auth types (OIDs in the spnego blob in the negprot response).
Change this so that on krb5 mounts we default to trying krb5 if the
server doesn't list its supported protocol mechanisms.
Steve French [Sun, 28 Oct 2018 05:47:11 +0000 (00:47 -0500)]
smb3: add trace point for tree connection
In debugging certain scenarios, especially reconnect cases,
it can be helpful to have a dynamic trace point for the
result of tree connect. See sample output below
from a reconnect event. The new event is 'smb3_tcon'
Ronnie Sahlberg [Thu, 25 Oct 2018 05:43:36 +0000 (15:43 +1000)]
cifs: fix return value for cifs_listxattr
If the application buffer was too small to fit all the names
we would still count the number of bytes and return this for
listxattr. This would then trigger a BUG in usercopy.c
Fix the computation of the size so that we return -ERANGE
correctly when the buffer is too small.
Guo Ren [Fri, 2 Nov 2018 16:51:28 +0000 (00:51 +0800)]
clocksource/drivers/c-sky: Add C-SKY SMP timer
The driver is for C-SKY SMP timer. It only supports oneshot event
and 32bit overflow for clocksource. Per cpu core has one timer and
all timers share one clock-counter-input from the same clocksource.
This use mfcr&mtcr instructions to access the regs.
__swiotlb_get_sgtable_page and __swiotlb_mmap_pfn are not only misnamed
but also only used if CONFIG_IOMMU_DMA is set. Just add a simple ifdef
for now, given that we plan to remove them entirely for the next merge
window.
Linus Torvalds [Fri, 2 Nov 2018 18:25:48 +0000 (11:25 -0700)]
Merge tag 'for-linus-20181102' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"The biggest part of this pull request is the revert of the blkcg
cleanup series. It had one fix earlier for a stacked device issue, but
another one was reported. Rather than play whack-a-mole with this,
revert the entire series and try again for the next kernel release.
Apart from that, only small fixes/changes.
Summary:
- Indentation fixup for mtip32xx (Colin Ian King)
- The blkcg cleanup series revert (Dennis Zhou)
- Two NVMe fixes. One fixing a regression in the nvme request
initialization in this merge window, causing nvme-fc to not work.
The other is a suspend/resume p2p resource issue (James, Keith)
- Fix sg discard merge, allowing us to merge in cases where we didn't
before (Jianchao Wang)
- Call rq_qos_exit() after the queue is frozen, preventing a hang
(Ming)
- Fix brd queue setup, fixing an oops if we fail setting up all
devices (Ming)"
* tag 'for-linus-20181102' of git://git.kernel.dk/linux-block:
nvme-pci: fix conflicting p2p resource adds
nvme-fc: fix request private initialization
blkcg: revert blkcg cleanups series
block: brd: associate with queue until adding disk
block: call rq_qos_exit() after queue is frozen
mtip32xx: clean an indentation issue, remove extraneous tabs
block: fix the DISCARD request merge
Linus Torvalds [Fri, 2 Nov 2018 18:22:45 +0000 (11:22 -0700)]
Merge tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This series contains a number of improvements to existing drivers,
such as LPSS. Some drivers, such as renesas-tpu and rcar get support
for more SoC generations. To round things off this fixes an issue with
the sysfs interface"
* tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: Only set update bit if we are actually changing the settings
pwm: lpss: Force runtime-resume on suspend on Cherry Trail
pwm: Enable TI ECAP driver for ARCH_K3
dt-bindings: pwm: tiecap: Add TI AM654 SoC specific compatible
dt-bindings: pwm: rcar: Add r8a774a1 support
pwm: Send a uevent on the pwmchip device upon channel sysfs (un)export
Revert "pwm: Set class for exported channels in sysfs"
dt-bindings: pwm: renesas-tpu: Document r8a7744 support
dt-bindings: pwm: rcar: Add r8a7744 support
dt-bindings: pwm: renesas: tpu: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: pwm-rcar: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: tpu: Fix "compatible" prop description
pwm: Use SPDX identifier for Renesas drivers
pwm: lpss: Add get_state callback
pwm: lpss: Release runtime-pm reference from the driver's remove callback
pwm: lpss: Check PWM powerstate after resume on Cherry Trail devices
pwm: lpss: Move struct pwm_lpss_chip definition to the header file
pwm: lpss: Add ACPI HID for second PWM controller on Cherry Trail devices
ACPI / PM: Export acpi_device_get_power() for use by modular build drivers
pwm: tegra: Remove gratuituous blank line
Marc Zyngier [Wed, 31 Oct 2018 08:41:34 +0000 (08:41 +0000)]
soc: ti: QMSS: Fix usage of irq_set_affinity_hint
The Keystone QMSS driver is pretty damaged, in the sense that it
does things like this:
irq_set_affinity_hint(irq, to_cpumask(&cpu_map));
where cpu_map is a local variable. As we leave the function, this
will point to nowhere-land, and things will end-up badly.
Instead, let's use a proper cpumask that gets allocated, giving
the driver a chance to actually work with things like irqbalance
as well as have a hypothetical 64bit future.
Linus Torvalds [Fri, 2 Nov 2018 18:17:22 +0000 (11:17 -0700)]
Merge tag 'edac_for_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull more EDAC updates from Borislav Petkov:
"The second part of the EDAC pile which contains the ADXL user and a
build fix which addresses a not-so-sensical .config but fixes
randconfig builds people do:
- skx_edac: Address translation for NVDIMMs (Tony Luck and Qiuxu Zhuo)
- ACPI_ADXL build fix"
[ I don't think "sensical" is a word, particularly when used in the
context of actually meaning "nonsensical", but I like it - Linus ]
* tag 'edac_for_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, skx: Fix randconfig builds
EDAC, skx_edac: Add address translation for non-volatile DIMMs
Anders Roxell [Tue, 30 Oct 2018 11:38:50 +0000 (12:38 +0100)]
arm64: kprobe: make page to RO mode when allocate it
Commit 1404d6f13e47 ("arm64: dump: Add checking for writable and exectuable pages")
has successfully identified code that leaves a page with W+X
permissions.
kprobes allocates a writable executable page with module_alloc() in
order to store executable code.
Reworked to that when allocate a page it sets mode RO. Inspired by
commit 63fef14fc98a ("kprobes/x86: Make insn buffer always ROX and use text_poke()").
Linus Torvalds [Fri, 2 Nov 2018 18:02:52 +0000 (11:02 -0700)]
Merge tag 'sound-fix-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few device-specific fixes: a fix for SPDIF on old Creative PCI
board, and two additional fixes for the recent changes in FireWire
audio stack"
* tag 'sound-fix-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: firewire-lib: fix insufficient PCM rule for period/buffer size
ALSA: ca0106: Disable IZD on SB0570 DAC to fix audio pops
ALSA: dice: fix to wait for releases of all ALSA character devices
projects / linux.git / log