Chris Wilson [Sun, 28 Jun 2015 13:18:16 +0000 (14:18 +0100)]
agp/intel: Fix typo in needs_ilk_vtd_wa()
In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against
the ids for the mobile GPU and the mobile host bridge. That latter is
impossible and so likely was just a typo for the desktop GPU device id
(which is also buggy).
Currently, watchdog subsystem require the misc subsystem to
register a watchdog. This may not be the case in case of an
early registration of a watchdog, which can be required when
the watchdog cannot be disabled.
This patch introduces a deferral mechanism to remove this requirement.
Tadeusz Struk [Sat, 27 Jun 2015 06:56:38 +0000 (15:56 +0900)]
crypto: aesni - fix failing setkey for rfc4106-gcm-aesni
rfc4106(gcm(aes)) uses ctr(aes) to generate hash key. ctr(aes) needs
chainiv, but the chainiv gets initialized after aesni_intel when both
are statically linked so the setkey fails.
This patch forces aesni_intel to be initialized after chainiv.
Markus Elfring [Fri, 26 Jun 2015 18:30:11 +0000 (20:30 +0200)]
crypto: qat - Deletion of unnecessary checks before two function calls
The functions kfree() and release_firmware() test whether their argument
is NULL and then return immediately.
Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Takashi Iwai [Mon, 29 Jun 2015 06:38:02 +0000 (08:38 +0200)]
ALSA: hda - Fix the dock headphone output on Fujitsu Lifebook E780
Fujitsu Lifebook E780 sets the sequence number 0x0f to only only of
the two headphones, thus the driver tries to assign another as the
line-out, and this results in the inconsistent mapping between the
created jack ctl and the actual I/O. Due to this, PulseAudio doesn't
handle it properly and gets the silent output.
This patch series fixes occasional BCM7xxx PHY driver binding failure due
to a harware bug where the first read or write does not come out of the PHY
MDIO management controller.
Since we have two different MDIO controllers using this PHY, a similar
need to be replicated in GENET and UniMAC MDIO.
====================
Florian Fainelli [Fri, 26 Jun 2015 17:39:06 +0000 (10:39 -0700)]
net: phy: mdio-bcm-unimac: workaround initial read failures for integrated PHYs
All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.
Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().
Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Florian Fainelli [Fri, 26 Jun 2015 17:39:05 +0000 (10:39 -0700)]
net: bcmgenet: workaround initial read failures for integrated PHYs
All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.
Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().
Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
The initial MDIO read or write towards the BCM7xxx integrated PHY may
fail, workaround this by inserting a dummy MII_BMSR read to force the
MDIO management controller to see at least one valid transaction and get
out of stuck state out of reset.
Michal Schmidt [Fri, 26 Jun 2015 15:50:00 +0000 (17:50 +0200)]
bnx2x: fix DMA API usage
With CONFIG_DMA_API_DEBUG=y bnx2x triggers the error "DMA-API: device
driver frees DMA memory with wrong function".
On archs where PAGE_SIZE > SGE_PAGE_SIZE it also triggers "DMA-API:
device driver frees DMA memory with different size".
Fix this by making the mapping and unmapping symmetric:
- Do not map the whole pool page at once. Instead map the
SGE_PAGE_SIZE-sized pieces individually, so they can be unmapped in
the same manner.
- What's mapped using dma_map_page() must be unmapped using
dma_unmap_page().
Tested on ppc64.
Fixes: 4cace675d687 ("bnx2x: Alloc 4k fragment for each rx ring buffer element") Signed-off-by: Michal Schmidt <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Before, the symbols depended implicitly on HAS_DMA through PCI or
USE_OF. Add explicit dependencies on HAS_DMA to fix this.
Fixes: b7d3282a245f4428 ("net: via/Kconfig: replace USE_OF with OF_???") Signed-off-by: Geert Uytterhoeven <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Steve French [Thu, 18 Jun 2015 09:49:47 +0000 (04:49 -0500)]
Update negotiate protocol for SMB3.11 dialect
Send negotiate contexts when SMB3.11 dialect is negotiated
(ie the preauth and the encryption contexts) and
Initialize SMB3.11 preauth negotiate context salt to random bytes
Followon patch will update session setup and tree connect
Steve French [Sun, 28 Jun 2015 04:18:36 +0000 (21:18 -0700)]
Add reflink copy over SMB3.11 with new FSCTL_DUPLICATE_EXTENTS
Getting fantastic copy performance with cp --reflink over SMB3.11
using the new FSCTL_DUPLICATE_EXTENTS.
This FSCTL was added in the SMB3.11 dialect (testing was
against REFS file system) so have put it as a 3.11 protocol
specific operation ("vers=3.1.1" on the mount). Tested at
the SMB3 plugfest in Redmond.
It depends on the new FS Attribute (BLOCK_REFCOUNTING) which
is used to advertise support for the ability to do this ioctl
(if you can support multiple files pointing to the same block
than this refcounting ability or equivalent is needed to
support the new reflink-like duplicate extent SMB3 ioctl.
David S. Miller [Mon, 29 Jun 2015 00:20:02 +0000 (17:20 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-06-26
This series contains fixes for igb, e1000e and i40evf.
Todd disables IPv6 extension header processing due to a hardware errata
and bumps the driver version.
Yanir provides six fixes for e1000e. First is a fix for a locking issue
where we were not always taking the pci_bus_sem semaphore all the time
when calling pci_disable_link_state_locked(), so fix the code to only call
pci_disable_link_state_locked() when the semaphore has been acquired,
otherwise call pci_disable_link_state(). A previous fix for i219 where
the hardware prevented ULP entry caused EEE in Sx not the be enabled, so
modify the code flow that allows both ULP and EEE in Sx. Fix an issue
when running 10/100 full duplex on i219 where CRC errors were occurring
by increasing the IPG from 8 to 0xC as per the hardware developers.
Fix a data corruption issue found on some platforms by increasing the
minimum gap between the PHY FIFO read and write pointers. Fix i219,
which does not require the K1 workaround for LPT devices.
Mitch provides a i40evf fix for a panic when changing MTU. Down was
requesting queue disables, but then exited immediately without waiting
for the queues to actually be disabled. This could allow any function
called after i40evf_down() to run immediately, including i40evf_up(),
and causes a memory leak. Fixed the issue by removing the whole
reinit_locked function which allows for the driver to handle the state
changes by requesting reset from the periodic timer. The second fix
resolves an issue where RSS was being configured as though it is using
the maximum number of queue. This can cause the device to drop a lot
of receive traffic, as the packets get assigned to non-functional queues.
This is resolved by only configuring RSS with the number of active queues.
====================
Shengzhou Liu [Fri, 26 Jun 2015 09:58:52 +0000 (17:58 +0800)]
net/phy: tune get_phy_c45_ids to support more c45 phy
As some C45 10G PHYs(e.g. Cortina CS4315/CS4340 PHY) have
zero Devices In package, current driver can't get correct
devices_in_package value by non-zero Devices In package.
so let's probe more with zero Devices In package to support
more C45 PHYs.
As bnx2x_init_ptp() is only called if bp->flags contains PTP_SUPPORTED,
we also need to guard bnx2x_stop_ptp() with same condition, otherwise
ptp_task workqueue is not initialized and kernel barfs on
cancel_work_sync()
Greg Ungerer [Sat, 20 Jun 2015 05:51:57 +0000 (15:51 +1000)]
net: fec: don't access RACC register when not available
Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.
Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.
To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.
Mugunthan V N [Thu, 25 Jun 2015 16:51:02 +0000 (22:21 +0530)]
net: phy: fix phy link up when limiting speed via device tree
When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
drivers: net: xgene: Pre-initialize ret in xgene_enet_get_resources()
If CONFIG_ACPI=n:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_get_resources’:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:951: warning: ‘ret’ may be used uninitialized in this function
If the driver is bound to a legacy platform device, ret will contain
arbitrary data. If it is non-zero, it will be returned to the caller as
an error code.
flow_dissector: Pre-initialize ip_proto in __skb_flow_dissect()
net/core/flow_dissector.c: In function ‘__skb_flow_dissect’:
net/core/flow_dissector.c:132: warning: ‘ip_proto’ may be used uninitialized in this function
Li, Liang Z [Fri, 26 Jun 2015 23:17:26 +0000 (07:17 +0800)]
xen-netfront: Remove the meaningless code
The function netif_set_real_num_tx_queues() will return -EINVAL if
the second parameter < 1, so call this function with the second
parameter set to 0 is meaningless.
Jon Paul Maloy [Sun, 28 Jun 2015 13:44:44 +0000 (09:44 -0400)]
tipc: purge backlog queue counters when broadcast link is reset
In commit 1f66d161ab3d8b518903fa6c3f9c1f48d6919e74
("tipc: introduce starvation free send algorithm")
we introduced a counter per priority level for buffers
in the link backlog queue. We also introduced a new
function tipc_link_purge_backlog(), to reset these
counters to zero when the link is reset.
Unfortunately, we missed to call this function when
the broadcast link is reset, with the result that the
values of these counters might be permanently skewed
when new nodes are attached. This may in the worst case
lead to permananent, but spurious, broadcast link
congestion, where no broadcast packets can be sent at
all.
Linus Torvalds [Sun, 28 Jun 2015 20:55:08 +0000 (13:55 -0700)]
Merge branch 'for-linus-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml
Pull UML updates from Richard Weinberger:
- remove hppfs ("HonePot ProcFS")
- initial support for musl libc
- uaccess cleanup
- random cleanups and bug fixes all over the place
* 'for-linus-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: (21 commits)
um: Don't pollute kernel namespace with uapi
um: Include sys/types.h for makedev(), major(), minor()
um: Do not use stdin and stdout identifiers for struct members
um: Do not use __ptr_t type for stack_t's .ss pointer
um: Fix mconsole dependency
um: Handle tracehook_report_syscall_entry() result
um: Remove copy&paste code from init.h
um: Stop abusing __KERNEL__
um: Catch unprotected user memory access
um: Fix warning in setup_signal_stack_si()
um: Rework uaccess code
um: Add uaccess.h to ldt.c
um: Add uaccess.h to syscalls_64.c
um: Add asm/elf.h to vma.c
um: Cleanup mem_32/64.c headers
um: Remove hppfs
um: Move syscall() declaration into os.h
um: kernel: ksyms: Export symbol syscall() for fixing modpost issue
um/os-Linux: Use char[] for syscall_stub declarations
um: Use char[] for linker script address declarations
...
Steve French [Wed, 24 Jun 2015 04:37:11 +0000 (23:37 -0500)]
Add SMB3.11 mount option synonym for new dialect
Most people think of SMB 3.1.1 as SMB version 3.11 so add synonym
for "vers=3.1.1" of "vers=3.11" on mount.
Also make sure that unlike SMB3.0 and 3.02 we don't send
validate negotiate on mount (it is handled by negotiate contexts) -
add list of SMB3.11 specific functions (distinct from 3.0 dialect).
Steve French [Thu, 18 Dec 2014 04:52:58 +0000 (22:52 -0600)]
Allow parsing vers=3.11 on cifs mount
Parses and recognizes "vers=3.1.1" on cifs mount and allows sending
0x0311 as a new CIFS/SMB3 dialect. Subsequent patches will add
the new negotiate contexts and updated session setup
Linus Torvalds [Sat, 27 Jun 2015 20:53:16 +0000 (13:53 -0700)]
Merge branch 'upstream' of git://git.infradead.org/users/pcmoore/audit
Pull audit updates from Paul Moore:
"Four small audit patches for v4.2, all bug fixes. Only 10 lines of
change this time so very unremarkable, the patch subject lines pretty
much tell the whole story"
* 'upstream' of git://git.infradead.org/users/pcmoore/audit:
audit: Fix check of return value of strnlen_user()
audit: obsolete audit_context check is removed in audit_filter_rules()
audit: fix for typo in comment to function audit_log_link_denied()
lsm: rename duplicate labels in LSM_AUDIT_DATA_TASK audit message type
Linus Torvalds [Sat, 27 Jun 2015 20:26:03 +0000 (13:26 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"The main change in this kernel is Casey's generalized LSM stacking
work, which removes the hard-coding of Capabilities and Yama stacking,
allowing multiple arbitrary "small" LSMs to be stacked with a default
monolithic module (e.g. SELinux, Smack, AppArmor).
See
https://lwn.net/Articles/636056/
This will allow smaller, simpler LSMs to be incorporated into the
mainline kernel and arbitrarily stacked by users. Also, this is a
useful cleanup of the LSM code in its own right"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
tpm, tpm_crb: fix le64_to_cpu conversions in crb_acpi_add()
vTPM: set virtual device before passing to ibmvtpm_reset_crq
tpm_ibmvtpm: remove unneccessary message level.
ima: update builtin policies
ima: extend "mask" policy matching support
ima: add support for new "euid" policy condition
ima: fix ima_show_template_data_ascii()
Smack: freeing an error pointer in smk_write_revoke_subj()
selinux: fix setting of security labels on NFS
selinux: Remove unused permission definitions
selinux: enable genfscon labeling for sysfs and pstore files
selinux: enable per-file labeling for debugfs files.
selinux: update netlink socket classes
signals: don't abuse __flush_signals() in selinux_bprm_committed_creds()
selinux: Print 'sclass' as string when unrecognized netlink message occurs
Smack: allow multiple labels in onlycap
Smack: fix seq operations in smackfs
ima: pass iint to ima_add_violation()
ima: wrap event related data to the new ima_event_data structure
integrity: add validity checks for 'path' parameter
...
Linus Torvalds [Sat, 27 Jun 2015 19:44:34 +0000 (12:44 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Andrew Morton [Sat, 27 Jun 2015 18:20:34 +0000 (12:20 -0600)]
drivers/block/nvme-core.c: fix build with gcc-4.4.4
gcc-4.4.4 (and possibly other versions) fail the compile when initializers
are used with anonymous unions. Work around this.
drivers/block/nvme-core.c: In function 'nvme_identify_ctrl':
drivers/block/nvme-core.c:1163: error: unknown field 'identify' specified in initializer
drivers/block/nvme-core.c:1163: warning: missing braces around initializer
drivers/block/nvme-core.c:1163: warning: (near initialization for 'c.<anonymous>')
drivers/block/nvme-core.c:1164: error: unknown field 'identify' specified in initializer
drivers/block/nvme-core.c:1164: warning: excess elements in struct initializer
drivers/block/nvme-core.c:1164: warning: (near initialization for 'c')
...
This patch has no effect on text size with gcc-4.8.2.
bdi: Remove "inline" keyword from exported I_BDEV() implementation
With gcc 3.4.6/4.1.2/4.2.4 (not with 4.4.7/4.6.4/4.8.4):
CC fs/block_dev.o
include/linux/fs.h:804: warning: ‘I_BDEV’ declared inline after being called
include/linux/fs.h:804: warning: previous declaration of ‘I_BDEV’ was here
Commit a212b105b07d75b4 ("bdi: make inode_to_bdi() inline") added a
caller of I_BDEV() in a header file, exposing the bogus "inline" on the
exported implementation.
Keith Busch [Thu, 18 Jun 2015 19:36:40 +0000 (13:36 -0600)]
NVMe: Fix filesystem deadlock on removal
Move gendisk deletion before controller shutdown so filesystem may sync
dirty pages. Before, this would deadlock trying to allocate requests
on frozen queues that are about to be deleted.
Keith Busch [Thu, 18 Jun 2015 19:36:39 +0000 (13:36 -0600)]
NVMe: Failed controller initialization fixes
This fixes an infinite device reset loop that may occur on devices that
fail initialization. If the drive fails to become ready for any reason
that does not involve an admin command timeout, the probe task should
assume the drive is unavailable and remove it from the topology. In
the case an admin command times out during device probing, the driver's
existing reset action will handle removing the drive.
Keith Busch [Mon, 8 Jun 2015 16:08:15 +0000 (10:08 -0600)]
NVMe: Unify controller probe and resume
This unifies probe and resume so they both may be scheduled in the same
way. This is necessary for error handling that may occur during device
initialization since the task to cleanup the device wouldn't be able to
run if it is blocked on device initialization.
Keith Busch [Mon, 8 Jun 2015 16:08:13 +0000 (10:08 -0600)]
NVMe: Fix device cleanup on initialization failure
Don't release block queue and tagging resoureces if the driver never
got them in the first place. This can happen if the controller fails to
become ready, if memory wasn't available to allocate a tagset or admin
queue, or if the resources were released as part of error recovery.
Linus Torvalds [Sat, 27 Jun 2015 17:14:39 +0000 (10:14 -0700)]
Merge branch 'for-4.2' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"A relatively quiet cycle, with a mix of cleanup and smaller bugfixes"
* 'for-4.2' of git://linux-nfs.org/~bfields/linux: (24 commits)
sunrpc: use sg_init_one() in krb5_rc4_setup_enc/seq_key()
nfsd: wrap too long lines in nfsd4_encode_read
nfsd: fput rd_file from XDR encode context
nfsd: take struct file setup fully into nfs4_preprocess_stateid_op
nfsd: refactor nfs4_preprocess_stateid_op
nfsd: clean up raparams handling
nfsd: use swap() in sort_pacl_range()
rpcrdma: Merge svcrdma and xprtrdma modules into one
svcrdma: Add a separate "max data segs macro for svcrdma
svcrdma: Replace GFP_KERNEL in a loop with GFP_NOFAIL
svcrdma: Keep rpcrdma_msg fields in network byte-order
svcrdma: Fix byte-swapping in svc_rdma_sendto.c
nfsd: Update callback sequnce id only CB_SEQUENCE success
nfsd: Reset cb_status in nfsd4_cb_prepare() at retrying
svcrdma: Remove svc_rdma_xdr_decode_deferred_req()
SUNRPC: Move EXPORT_SYMBOL for svc_process
uapi/nfs: Add NFSv4.1 ACL definitions
nfsd: Remove dead declarations
nfsd: work around a gcc-5.1 warning
nfsd: Checking for acl support does not require fetching any acls
...
Linus Torvalds [Sat, 27 Jun 2015 16:47:46 +0000 (09:47 -0700)]
Merge tag 'gfs2-merge-window' of git://git.kernel.org:/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull GFS2 updates from Bob Peterson:
"Here are the patches we've accumulated for GFS2 for the current
upstream merge window. We have a good mixture this time. Here are
some of the features:
- Fix a problem with RO mounts writing to the journal.
- Further improvements to quotas on GFS2.
- Added support for rename2 and RENAME_EXCHANGE on GFS2.
- Increase performance by making glock lru_list less of a bottleneck.
- Increase performance by avoiding unnecessary buffer_head releases.
- Increase performance by using average glock round trip time from all CPUs.
- Fixes for some compiler warnings and minor white space issues.
- Other misc bug fixes"
* tag 'gfs2-merge-window' of git://git.kernel.org:/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
GFS2: Don't brelse rgrp buffer_heads every allocation
GFS2: Don't add all glocks to the lru
gfs2: Don't support fallocate on jdata files
gfs2: s64 cast for negative quota value
gfs2: limit quota log messages
gfs2: fix quota updates on block boundaries
gfs2: fix shadow warning in gfs2_rbm_find()
gfs2: kerneldoc warning fixes
gfs2: convert simple_str to kstr
GFS2: make sure S_NOSEC flag isn't overwritten
GFS2: add support for rename2 and RENAME_EXCHANGE
gfs2: handle NULL rgd in set_rgrp_preferences
GFS2: inode.c: indent with TABs, not spaces
GFS2: mark the journal idle to fix ro mounts
GFS2: Average in only non-zero round-trip times for congestion stats
GFS2: Use average srttb value in congestion calculations
which is not easily reproducible (I've seen it just once, and then Ted
was able to reproduce it once). Revert it while Ted and Jan try to
figure out what is wrong.
Takashi Iwai [Sat, 27 Jun 2015 08:21:13 +0000 (10:21 +0200)]
ALSA: hda - Add headset support to Acer Aspire V5
Acer Aspire V5 with ALC282 codec needs the similar quirk like Dell
laptops to support the headset mic. The headset mic pin is 0x19 and
it's not exposed by BIOS, thus we need to fix the pincfg as well.
Linus Torvalds [Sat, 27 Jun 2015 03:12:21 +0000 (20:12 -0700)]
Merge branch 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue updates from Tejun Heo:
"Most of the changes are around implementing and fixing fallouts from
sysfs and internal interface to limit the CPUs available to all
unbound workqueues to help isolating CPUs. It needs more work as
ordered workqueues can roam unrestricted but still is a significant
improvement"
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix typos in comments
workqueue: move flush_scheduled_work() to workqueue.h
workqueue: remove the lock from wq_sysfs_prep_attrs()
workqueue: remove the declaration of copy_workqueue_attrs()
workqueue: ensure attrs changes are properly synchronized
workqueue: separate out and refactor the locking of applying attrs
workqueue: simplify wq_update_unbound_numa()
workqueue: wq_pool_mutex protects the attrs-installation
workqueue: fix a typo
workqueue: function name in the comment differs from the real function name
workqueue: fix trivial typo in Documentation/workqueue.txt
workqueue: Allow modifying low level unbound workqueue cpumask
workqueue: Create low-level unbound workqueues cpumask
workqueue: split apply_workqueue_attrs() into 3 stages
Linus Torvalds [Sat, 27 Jun 2015 02:50:04 +0000 (19:50 -0700)]
Merge branch 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- threadgroup_lock got reorganized so that its users can pick the
actual locking mechanism to use. Its only user - cgroups - is
updated to use a percpu_rwsem instead of per-process rwsem.
This makes things a bit lighter on hot paths and allows cgroups to
perform and fail multi-task (a process) migrations atomically.
Multi-task migrations are used in several places including the
unified hierarchy.
- Delegation rule and documentation added to unified hierarchy. This
will likely be the last interface update from the cgroup core side
for unified hierarchy before lifting the devel mask.
- Some groundwork for the pids controller which is scheduled to be
merged in the coming devel cycle.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: add delegation section to unified hierarchy documentation
cgroup: require write perm on common ancestor when moving processes on the default hierarchy
cgroup: separate out cgroup_procs_write_permission() from __cgroup_procs_write()
kernfs: make kernfs_get_inode() public
MAINTAINERS: add a cgroup core co-maintainer
cgroup: fix uninitialised iterator in for_each_subsys_which
cgroup: replace explicit ss_mask checking with for_each_subsys_which
cgroup: use bitmask to filter for_each_subsys
cgroup: add seq_file forward declaration for struct cftype
cgroup: simplify threadgroup locking
sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem
sched, cgroup: reorganize threadgroup locking
cgroup: switch to unsigned long for bitmasks
cgroup: reorganize include/linux/cgroup.h
cgroup: separate out include/linux/cgroup-defs.h
cgroup: fix some comment typos
Stephen Rothwell [Mon, 25 May 2015 11:00:24 +0000 (21:00 +1000)]
power: axp288_charger: fix for API change
Caused by commit 843735b788a4 ("power: axp288_charger: axp288 charger
driver") from the battery tree interacting with commit 046050f6e623
("extcon: Update the prototype of extcon_register_notifier() with enum
extcon") from the extcon tree.
Linus Torvalds [Sat, 27 Jun 2015 00:40:54 +0000 (17:40 -0700)]
Merge tag 'dma-buf-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
"Minor changes for 4.2
- add ref-counting for kernel modules as exporters
- minor code style fixes"
* tag 'dma-buf-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
dma-buf: Minor coding style fixes
dma-buf: add ref counting for module as exporter
Linus Torvalds [Fri, 26 Jun 2015 22:59:26 +0000 (15:59 -0700)]
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
Linus Torvalds [Fri, 26 Jun 2015 22:53:22 +0000 (15:53 -0700)]
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
Linus Torvalds [Fri, 26 Jun 2015 22:46:08 +0000 (15:46 -0700)]
Merge tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big, really big, staging tree patches for 4.2-rc1.
Loads of stuff in here, almost all just coding style fixes / churn,
and a few new drivers as well, one of which I just disabled from the
build a few minutes ago due to way too many build warnings.
Other than the one "disable this driver" patch, all of these have been
in linux-next for quite a while with no reported issues"
* tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1163 commits)
staging: wilc1000: disable driver due to build warnings
Staging: rts5208: fix CHANGE_LINK_STATE value
Staging: sm750fb: ddk750_swi2c.c: Insert spaces before parenthesis
Staging: sm750fb: ddk750_swi2c.c: Place braces on correct lines
Staging: sm750fb: ddk750_swi2c.c: Insert spaces around operators
Staging: sm750fb: ddk750_swi2c.c: Replace spaces with tabs
Staging: sm750fb: ddk750_swi2c.h: Shorten lines to under 80 characters
Staging: sm750fb: ddk750_swi2c.h: Replace spaces with tabs
Staging: sm750fb: modedb.h: Shorten lines to under 80 characters
Staging: sm750fb: modedb.h: Replace spaces with tabs
staging: comedi: addi_apci_3120: rename 'this_board' variables
staging: comedi: addi_apci_1516: rename 'this_board' variables
staging: comedi: ni_atmio: cleanup ni_getboardtype()
staging: comedi: vmk80xx: sanity check context used to get the boardinfo
staging: comedi: vmk80xx: rename 'boardinfo' variables
staging: comedi: dt3000: rename 'this_board' variables
staging: comedi: adv_pci_dio: rename 'this_board' variables
staging: comedi: cb_pcidas64: rename 'thisboard' variables
staging: comedi: cb_pcidas: rename 'thisboard' variables
staging: comedi: me4000: rename 'thisboard' variables
...
Linus Torvalds [Fri, 26 Jun 2015 22:07:37 +0000 (15:07 -0700)]
Merge tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core / firmware changes for 4.2-rc1.
A number of small changes all over the place in the driver core, and
in the firmware subsystem. Nothing really major, full details in the
shortlog. Some of it is a bit of churn, given that the platform
driver probing changes was found to not work well, so they were
reverted.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
Revert "base/platform: Only insert MEM and IO resources"
Revert "base/platform: Continue on insert_resource() error"
Revert "of/platform: Use platform_device interface"
Revert "base/platform: Remove code duplication"
firmware: add missing kfree for work on async call
fs: sysfs: don't pass count == 0 to bin file readers
base:dd - Fix for typo in comment to function driver_deferred_probe_trigger().
base/platform: Remove code duplication
of/platform: Use platform_device interface
base/platform: Continue on insert_resource() error
base/platform: Only insert MEM and IO resources
firmware: use const for remaining firmware names
firmware: fix possible use after free on name on asynchronous request
firmware: check for file truncation on direct firmware loading
firmware: fix __getname() missing failure check
drivers: of/base: move of_init to driver_init
drivers/base: cacheinfo: fix annoying typo when DT nodes are absent
sysfs: disambiguate between "error code" and "failure" in comments
driver-core: fix build for !CONFIG_MODULES
driver-core: make __device_attach() static
...
Linus Torvalds [Fri, 26 Jun 2015 21:51:15 +0000 (14:51 -0700)]
Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
Linus Torvalds [Fri, 26 Jun 2015 21:02:43 +0000 (14:02 -0700)]
Merge tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This patch series contains several clean ups and even a new trace
clock "monitonic raw". Also some enhancements to make the ring buffer
even faster. But the biggest and most noticeable change is the
renaming of the ftrace* files, structures and variables that have to
deal with trace events.
Over the years I've had several developers tell me about their
confusion with what ftrace is compared to events. Technically,
"ftrace" is the infrastructure to do the function hooks, which include
tracing and also helps with live kernel patching. But the trace
events are a separate entity altogether, and the files that affect the
trace events should not be named "ftrace". These include:
And a few various variables and flags have also been updated.
This has been sitting in linux-next for some time, and I have not
heard a single complaint about this rename breaking anything. Mostly
because these functions, variables and structures are mostly internal
to the tracing system and are seldom (if ever) used by anything
external to that"
* tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
ring_buffer: Allow to exit the ring buffer benchmark immediately
ring-buffer-benchmark: Fix the wrong type
ring-buffer-benchmark: Fix the wrong param in module_param
ring-buffer: Add enum names for the context levels
ring-buffer: Remove useless unused tracing_off_permanent()
ring-buffer: Give NMIs a chance to lock the reader_lock
ring-buffer: Add trace_recursive checks to ring_buffer_write()
ring-buffer: Allways do the trace_recursive checks
ring-buffer: Move recursive check to per_cpu descriptor
ring-buffer: Add unlikelys to make fast path the default
tracing: Rename ftrace_get_offsets_##call() to trace_event_get_offsets_##call()
tracing: Rename ftrace_define_fields_##call() to trace_event_define_fields_##call()
tracing: Rename ftrace_event_type_funcs_##call to trace_event_type_funcs_##call
tracing: Rename ftrace_data_offset_##call to trace_event_data_offset_##call
tracing: Rename ftrace_raw_##call event structures to trace_event_raw_##call
tracing: Rename ftrace_trigger_soft_disabled() to trace_trigger_soft_disabled()
tracing: Rename FTRACE_EVENT_FL_* flags to EVENT_FILE_FL_*
tracing: Rename struct ftrace_subsystem_dir to trace_subsystem_dir
tracing: Rename ftrace_event_name() to trace_event_name()
tracing: Rename FTRACE_MAX_EVENT to TRACE_EVENT_TYPE_MAX
...
Thomas Gleixner [Fri, 26 Jun 2015 20:08:38 +0000 (22:08 +0200)]
timer: Fix hotplug regression
The recent timer wheel rework removed the get/put_cpu_var() pair in
the hotplug migration code, which results in:
BUG: using smp_processor_id() in preemptible [00000000] code: hib.sh/2845
...
[<ffffffff810d4fa3>] timer_cpu_notify+0x53/0x12
That hunk is a leftover from an earlier iteration and went unnoticed
so far.
Restore the previous code which was obviously correct.
Fixes: 0eeda71bc30d 'timer: Replace timer base by a cpu index'
Reported-and_tested-by: Borislav Petkov <[email protected]> Signed-off-by: Thomas Gleixner <[email protected]>
Linus Torvalds [Fri, 26 Jun 2015 20:56:55 +0000 (13:56 -0700)]
Merge tag 'trace-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This isn't my 4.2 pull request (yet). I found a few more bugs that I
would have sent to fix 4.1, but since 4.1 is already out, I'm sending
this before sending my 4.2 request (which is ready to go).
After fixing the previous filter issue reported by Vince Weaver, I
could not come up with a situation where the operand counter (cnt)
could go below zero, so I added a WARN_ON_ONCE(cnt < 0). Vince was
able to trigger that warn on with his fuzzer test, but didn't have a
filter input that caused it.
Later, Sasha Levin was able to trigger that same warning, and was able
to give me the filter string that triggered it. It was simply a
single operation ">".
I wrapped the filtering code in a userspace program such that I could
single step through the logic. With a single operator the operand
counter can legitimately go below zero, and should be reported to the
user as an error, but should not produce a kernel warning. The
WARN_ON_ONCE(cnt < 0) should be just a "if (cnt < 0) break;" and the
code following it will produce the error message for the user.
While debugging this, I found that there was another bug that let the
pointer to the filter string go beyond the filter string. This too
was fixed.
Finally, there was a typo in a stub function that only gets compiled
if trace events is disabled but tracing is enabled (I'm not even sure
that's possible)"
* tag 'trace-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix typo from "static inlin" to "static inline"
tracing/filter: Do not allow infix to exceed end of string
tracing/filter: Do not WARN on operand count going below zero
Linus Torvalds [Fri, 26 Jun 2015 20:18:51 +0000 (13:18 -0700)]
Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
Damian Eppel [Fri, 26 Jun 2015 13:23:04 +0000 (15:23 +0200)]
clocksource: exynos_mct: Avoid blocking calls in the cpu hotplug notifier
Whilst testing cpu hotplug events on kernel configured with
DEBUG_PREEMPT and DEBUG_ATOMIC_SLEEP we get following BUG message,
caused by calling request_irq() and free_irq() in the context of
hotplug notification (which is in this case atomic context).
[ 40.785859] CPU1: Software reset
[ 40.786660] BUG: sleeping function called from invalid context at mm/slub.c:1241
[ 40.786668] in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/1
[ 40.786678] Preemption disabled at:[< (null)>] (null)
[ 40.786681]
[ 40.786692] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.19.0-rc4-00024-g7dca860 #36
[ 40.786698] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 40.786728] [<c0014a00>] (unwind_backtrace) from [<c0011980>] (show_stack+0x10/0x14)
[ 40.786747] [<c0011980>] (show_stack) from [<c0449ba0>] (dump_stack+0x70/0xbc)
[ 40.786767] [<c0449ba0>] (dump_stack) from [<c00c6124>] (kmem_cache_alloc+0xd8/0x170)
[ 40.786785] [<c00c6124>] (kmem_cache_alloc) from [<c005d6f8>] (request_threaded_irq+0x64/0x128)
[ 40.786804] [<c005d6f8>] (request_threaded_irq) from [<c0350b8c>] (exynos4_local_timer_setup+0xc0/0x13c)
[ 40.786820] [<c0350b8c>] (exynos4_local_timer_setup) from [<c0350ca8>] (exynos4_mct_cpu_notify+0x30/0xa8)
[ 40.786838] [<c0350ca8>] (exynos4_mct_cpu_notify) from [<c003b330>] (notifier_call_chain+0x44/0x84)
[ 40.786857] [<c003b330>] (notifier_call_chain) from [<c0022fd4>] (__cpu_notify+0x28/0x44)
[ 40.786873] [<c0022fd4>] (__cpu_notify) from [<c0013714>] (secondary_start_kernel+0xec/0x150)
[ 40.786886] [<c0013714>] (secondary_start_kernel) from [<40008764>] (0x40008764)
Interrupts cannot be requested/freed in the CPU_STARTING/CPU_DYING
notifications which run on the hotplugged cpu with interrupts and
preemption disabled.
To avoid the issue, request the interrupts for all possible cpus in
the boot code. The interrupts are marked NO_AUTOENABLE to avoid a racy
request_irq/disable_irq() sequence. The flag prevents the
request_irq() code from enabling the interrupt immediately.
The interrupt is then enabled in the CPU_STARTING notifier of the
hotplugged cpu and again disabled with disable_irq_nosync() in the
CPU_DYING notifier.
Linus Torvalds [Fri, 26 Jun 2015 19:35:01 +0000 (12:35 -0700)]
Merge tag 'dm-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Apologies for not pressing this request-based DM partial completion
issue further, it was an oversight on my part. We'll have to get it
fixed up properly and revisit for a future release.
- Revert block and DM core changes the removed request-based DM's
ability to handle partial request completions -- otherwise with the
current SCSI LLDs these changes could lead to silent data
corruption.
- Fix two DM version bumps that were missing from the initial 4.2 DM
pull request (enabled userspace lvm2 to know certain changes have
been made)"
* tag 'dm-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache policy smq: fix "default" version to be 1.4.0
dm: bump the ioctl version to 4.32.0
Revert "block, dm: don't copy bios for request clones"
Revert "dm: do not allocate any mempools for blk-mq request-based DM"
The main use case for the exisiting __irq_set_*_locked() inlines is to
replace the handler [,chip and name] of an interrupt from a region
which has the irq descriptor lock held, e.g. from the irq_set_type()
callback. The first argument is the irq number, so the functions need
so perform a pointless lookup of the interrupt descriptor for those
cases which have the irq_data pointer handy.
Provide new functions which take an irq_data pointer instead of the
interrupt number, so the lookup of the interrupt descriptor can be
avoided.
Linus Torvalds [Fri, 26 Jun 2015 19:20:00 +0000 (12:20 -0700)]
Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
"Bigger items included in this update are:
- A series of updates from Arnd for ARM randconfig build failures
- Updates from Dmitry for StrongARM SA-1100 to move IRQ handling to
drivers/irqchip/
- Move ARMs SP804 timer to drivers/clocksource/
- Perf updates from Mark Rutland in preparation to move the ARM perf
code into drivers/ so it can be shared with ARM64.
- MCPM updates from Nicolas
- Add support for taking platform serial number from DT
- Re-implement Keystone2 physical address space switch to conform to
architecture requirements
- Clean up ARMv7 LPAE code, which goes in hand with the Keystone2
changes.
- L2C cleanups to avoid unlocking caches if we're prevented by the
secure support to unlock.
- Avoid cleaning a potentially dirty cache containing stale data on
CPU initialisation
- Add ARM-only entry point for secondary startup (for machines that
can only call into a Thumb kernel in ARM mode). Same thing is also
done for the resume entry point.
- Provide arch_irqs_disabled via asm-generic
- Enlarge ARMv7M vector table
- Always use BFD linker for VDSO, as gold doesn't accept some of the
options we need.
- Fix an incorrect BSYM (for Thumb symbols) usage, and convert all
BSYM compiler macros to a "badr" (for branch address).
- Shut up compiler warnings provoked by our cmpxchg() implementation.
- Ensure bad xchg sizes fail to link"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (75 commits)
ARM: Fix build if CLKDEV_LOOKUP is not configured
ARM: fix new BSYM() usage introduced via for-arm-soc branch
ARM: 8383/1: nommu: avoid deprecated source register on mov
ARM: 8391/1: l2c: add options to overwrite prefetching behavior
ARM: 8390/1: irqflags: Get arch_irqs_disabled from asm-generic
ARM: 8387/1: arm/mm/dma-mapping.c: Add arm_coherent_dma_mmap
ARM: 8388/1: tcm: Don't crash when TCM banks are protected by TrustZone
ARM: 8384/1: VDSO: force use of BFD linker
ARM: 8385/1: VDSO: group link options
ARM: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
ARM: remove __bad_xchg definition
ARM: 8369/1: ARMv7M: define size of vector table for Vybrid
ARM: 8382/1: clocksource: make ARM_TIMER_SP804 depend on GENERIC_SCHED_CLOCK
ARM: 8366/1: move Dual-Timer SP804 driver to drivers/clocksource
ARM: 8365/1: introduce sp804_timer_disable and remove arm_timer.h inclusion
ARM: 8364/1: fix BE32 module loading
ARM: 8360/1: add secondary_startup_arm prototype in header file
ARM: 8359/1: correct secondary_startup_arm mode
ARM: proc-v7: sanitise and document registers around errata
ARM: proc-v7: clean up MIDR access
...
Linus Torvalds [Fri, 26 Jun 2015 19:11:23 +0000 (12:11 -0700)]
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Kevin Hilman:
"We keep collecting defconfig updates in a separate branch mostly to
encourage people to handle them separately and avoid conflicts between
different topics.
Most of these are enablement of new SoCs, boards or drivers that have
come in, or minor config refreshes due to reorderings in Kconfig
files, etc. I.e. mostly minor churn of various kinds"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: multi_v7_defconfig: remove duplicate CONFIG_COMMON_CLK_QCOM=y
ARM: multi_v7_defconfig: Enable display on Trats2 board
ARM64: add GPIO keys to the defconfig
ARM: keystone: defconfig: enable netcp driver by default
ARM: exynos_defconfig: Enable CONFIG_SENSORS_INA2XX for Odroid-XU3
ARM: exynos_defconfig: Enable CONFIG_SENSORS_PWM_FAN for Odroid-XU3
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_PIXCIR
ARM: omap2plus_defconfig: Add dm816x USB PHY as a loadable module
ARM: omap2plus_defconifg: Enable DM9000 in omap2plus_defconfig
ARM: lpc18xx: remove DEBUG_LL_UART_8250 from defconfig
ARM: multi_v7_defconfig: Make media support modular
ARM: multi_v7_defconfig: Make sound support modular
ARM: multi_v7_defconfig: Enable shmobile r8a7778/bockw platform
ARM: exynos_defconfig: savedefconfig
ARM: exynos_defconfig: Enable display on Trats2 board
ARM: multi_v7_defconfig: Enable OHCI on exynos SoCs
ARM: multi_v7_defconfig: Enable TMU for exynos SoCs
ARM: multi_v7_defconfig: Enable PMIC and MUIC drivers for exynos
ARM: multi_v7_defconfig: Enable CPU idle for exynos SoCs
ARM: multi_v7_defconfig: Enable Cypress APA I2C Trackpad support
...
staging: wilc1000: disable driver due to build warnings
The wilc1000 has just too many build warnings to be able to enable it
for the 4.2 release. Given that there have not been any patches
submitted to properly fix these obvious errors, I'm going to disable it
for now. I will enable it back when the build warning fixes are
submitted, or, if that never happens, I will remove it from the tree.
Linus Torvalds [Fri, 26 Jun 2015 18:54:29 +0000 (11:54 -0700)]
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Kevin Hilman:
"Some of these are for drivers/soc, where we're now putting
SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
Some highlights:
- simple-mfd: document DT bindings and misc updates
- migrate mach-berlin to simple-mfd for clock, pinctrl and reset
- memory: support for Tegra132 SoC
- memory: introduce tegra EMC driver for scaling memory frequency
- misc. updates for ARM CCI and CCN busses"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: soc: sunxi: Introduce SoC driver to map SRAMs
arm-cci: Add aliases for PMU events
arm-cci: Add CCI-500 PMU support
arm-cci: Sanitise CCI400 PMU driver specific code
arm-cci: Abstract handling for CCI events
arm-cci: Abstract out the PMU counter details
arm-cci: Cleanup PMU driver code
arm-cci: Do not enable CCI-400 PMU by default
firmware: qcom: scm: Add HDCP Support
ARM: berlin: add an ADC node for the BG2Q
ARM: berlin: remove useless chip and system ctrl compatibles
clk: berlin: drop direct of_iomap of nodes reg property
ARM: berlin: move BG2Q clock node
ARM: berlin: move BG2CD clock node
ARM: berlin: move BG2 clock node
clk: berlin: prepare simple-mfd conversion
pinctrl: berlin: drop SoC stub provided regmap
ARM: berlin: move pinctrl to simple-mfd nodes
pinctrl: berlin: prepare to use regmap provided by syscon
reset: berlin: drop arch_initcall initialization
...
Trond Myklebust [Fri, 26 Jun 2015 18:51:32 +0000 (14:51 -0400)]
pNFS/flexfiles: Turn off layoutcommit for servers that don't need it
This patch ensures that we record the value of 'ffl_flags' from
the layout, and then checks for the presence of the
FF_FLAGS_NO_LAYOUTCOMMIT flag before deciding whether or not to
call pnfs_set_layoutcommit().
The effect is that servers now can decide whether or not they want
the client to call layoutcommit before returning a writeable layout.
Linus Torvalds [Fri, 26 Jun 2015 18:43:59 +0000 (11:43 -0700)]
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Kevin Hilman:
"As usual, quite a few device-tree updates in ARM land. There was one
minor churn in DTs due to relicensing under a dual-license, and lots
of little additions of new peripherals, features etc, but nothing
really exciting to call to your attention. Some higlights, focsuing
on support for new SoCs and boards:
- AT91: new boards: Overkiz, Acme Systems' Arietta G25
- tegra: HDA support
- bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
RT-AC87U
- mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
boards, DLink DNS-327L
- OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
SL50
- ARM: added support for Juno r1 board
- sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
Mele A1000G
- imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
Gateworks GW5510, and aristainetos2 boards
- hisilicon: hi6220 SoC support; new boards: 96boards hikey"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
ARM: hisi: revert changes from hisi/hip04-dt branch
ARM: nomadik: set proper compatible for accelerometer
ARM64: juno: add GPIO keys
ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
ARM: dts: Introduce STM32F429 MCU
ARM: socfpga: dts: enable ethernet for Arria10 devkit
ARM: dts: k2l: fix the netcp range size
ARM: dts: k2e: fix the netcp range size
ARM: dts: k2hk: fix the netcp range size
ARM: dts: k2l-evm: Add device bindings for netcp driver
ARM: dts: k2e-evm: Add device bindings for netcp driver
ARM: dts: k2hk-evm: Add device bindings for netcp driver
ARM: BCM5301X: Add DT for Asus RT-AC87U
ARM: BCM5301X: add IRQ numbers for PCIe controller
ARM: BCM5301X: add NAND flash chip description
arm64: dts: Add dts files for Hisilicon Hi6220 SoC
clk: hi6220: Document devicetree bindings for hi6220 clock
arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
ARM: at91/dt: sama5d4ek: mci0 uses slot 0
ARM: at91/dt: kizbox: fix mismatch LED PWM device
...
Linus Torvalds [Fri, 26 Jun 2015 18:34:35 +0000 (11:34 -0700)]
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform support updates from Kevin Hilman:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. Some highlights from this round:
- sunxi: SMP support for A23 SoC
- socpga: big-endian support
- pxa: conversion to common clock framework
- bcm: SMP support for BCM63138
- imx: support new I.MX7D SoC
- zte: basic support for ZX296702 SoC"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
ARM: zx: Add basic defconfig support for ZX296702
ARM: dts: zx: add an initial zx296702 dts and doc
clk: zx: add clock support to zx296702
dt-bindings: Add #defines for ZTE ZX296702 clocks
ARM: socfpga: fix build error due to secondary_startup
MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
ARM: ep93xx: simone: support for SPI-based MMC/SD cards
MAINTAINERS: update Shawn's email to use kernel.org one
ARM: socfpga: support suspend to ram
ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
ARM: EXYNOS: register power domain driver from core_initcall
ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
ARM: SAMSUNG: Constify platform_device_id
ARM: EXYNOS: Constify irq_domain_ops
ARM: EXYNOS: add coupled cpuidle support for Exynos3250
ARM: EXYNOS: add exynos_get_boot_addr() helper
ARM: EXYNOS: add exynos_set_boot_addr() helper
ARM: EXYNOS: make exynos_core_restart() less verbose
ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
...
Linus Torvalds [Fri, 26 Jun 2015 18:08:27 +0000 (11:08 -0700)]
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Kevin Hilman:
"A relatively small setup of cleanups this time around, and similar to
last time the bulk of it is removal of legacy board support:
- OMAP: removal of legacy (non-DT) booting for several platforms
- i.MX: remove some legacy board files"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: fix EFM32 build breakage caused by cpu_resume_arm
ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
ARM: v7 setup function should invalidate L1 cache
mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
ARM: OMAP2+: Constify irq_domain_ops
ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
ARM: at91: remove useless Makefile.boot
ARM: at91: remove at91rm9200_sdramc.h
ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
ARM: at91/pm: use the atmel-mc syscon defines
pcmcia: at91_cf: Use syscon to configure the MC/smc
ARM: at91: declare the at91rm9200 memory controller as a syscon
mfd: syscon: Add Atmel MC (Memory Controller) registers definition
ARM: at91: drop sam9_smc.c
ata: at91: use syscon to configure the smc
ARM: ux500: delete static resource defines
ARM: ux500: rename ux500_map_io
ARM: ux500: look up PRCMU resource from DT
ARM: ux500: kill off L2CC static map
...
Trond Myklebust [Fri, 26 Jun 2015 18:01:59 +0000 (14:01 -0400)]
Merge branch 'layoutstats'
* layoutstats:
pnfs/flexfiles: protect ktime manipulation with mirror lock
nfs: provide pnfs_report_layoutstat when NFS42 is disabled
pnfs/flexfiles: report layoutstat regularly
nfs42: serialize LAYOUTSTATS calls of the same file
pnfs/flexfiles: encode LAYOUTSTATS flexfiles specific data
pnfs/flexfiles: add ff_layout_prepare_layoutstats
pNFS/flexfiles: track when layout is first used
pNFS/flexfiles: add layoutstats tracking
pNFS/flexfiles: Remove unused struct members user_name, group_name
pnfs: add pnfs_report_layoutstat helper function
pNFS: fill in nfs42_layoutstat_ops
NFSv.2/pnfs Add a LAYOUTSTATS rpc function
Peng Tao [Thu, 25 Jun 2015 10:19:32 +0000 (18:19 +0800)]
nfs: provide pnfs_report_layoutstat when NFS42 is disabled
kbuild test robot reported:
fs/built-in.o: In function `pnfs_report_layoutstat':
>> (.text+0x151a1c): undefined reference to `nfs42_proc_layoutstats_generic'
Linus Torvalds [Fri, 26 Jun 2015 16:52:05 +0000 (09:52 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge second patchbomb from Andrew Morton:
- most of the rest of MM
- lots of misc things
- procfs updates
- printk feature work
- updates to get_maintainer, MAINTAINERS, checkpatch
- lib/ updates
* emailed patches from Andrew Morton <[email protected]>: (96 commits)
exit,stats: /* obey this comment */
coredump: add __printf attribute to cn_*printf functions
coredump: use from_kuid/kgid when formatting corename
fs/reiserfs: remove unneeded cast
NILFS2: support NFSv2 export
fs/befs/btree.c: remove unneeded initializations
fs/minix: remove unneeded cast
init/do_mounts.c: add create_dev() failure log
kasan: remove duplicate definition of the macro KASAN_FREE_PAGE
fs/efs: femove unneeded cast
checkpatch: emit "NOTE: <types>" message only once after multiple files
checkpatch: emit an error when there's a diff in a changelog
checkpatch: validate MODULE_LICENSE content
checkpatch: add multi-line handling for PREFER_ETHER_ADDR_COPY
checkpatch: suggest using eth_zero_addr() and eth_broadcast_addr()
checkpatch: fix processing of MEMSET issues
checkpatch: suggest using ether_addr_equal*()
checkpatch: avoid NOT_UNIFIED_DIFF errors on cover-letter.patch files
checkpatch: remove local from codespell path
checkpatch: add --showfile to allow input via pipe to show filenames
...
Ross Zwisler [Thu, 25 Jun 2015 07:08:39 +0000 (03:08 -0400)]
arch, x86: pmem api for ensuring durability of persistent memory updates
Based on an original patch by Ross Zwisler [1].
Writes to persistent memory have the potential to be posted to cpu
cache, cpu write buffers, and platform write buffers (memory controller)
before being committed to persistent media. Provide apis,
memcpy_to_pmem(), wmb_pmem(), and memremap_pmem(), to write data to
pmem and assert that it is durable in PMEM (a persistent linear address
range). A '__pmem' attribute is added so sparse can track proper usage
of pointers to pmem.
This continues the status quo of pmem being x86 only for 4.2, but
reworks to ioremap, and wider implementation of memremap() will enable
other archs in 4.3.
projects / linux.git / log