serial: 8250_dma: Fix DMA Rx completion race

__dma_rx_complete() is called from two places:
  - Through the DMA completion callback dma_rx_complete()
  - From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.

Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().

Reported-by: Gilles BULOZ <gilles.buloz@kontron.com>
Tested-by: Gilles BULOZ <gilles.buloz@kontron.com>
Fixes: 9ee4b83e51f7 ("serial: 8250: Add support for dmaengine")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230130114841.25749-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler

Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.

Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.

Fixes: e359b4411c283 ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230120160332.57930-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-fixes-for-6.2a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next

Jonathan writes:
  "1st set of IIO fixes for the 6.2 cycle.

   The usual mixed bag - with a bunch of issues found by Carlos Song
   in the fxos8700 IMU driver dominating.

   hid-accel,gyro
    - Fix wrong returned value when read succeeds.
   marvell,berlin-adc
    - Missing of_node_put() in an error path.
   nxp,fxos8700 (freescale)
    - Wrong channel type match.
    - Swapped channel read back.
    - Incomplete channel read back (not enough bytes).
    - Missing shift of acceleration data.
    - Range selection didn't work (datasheet bug)
    - Wrong ODR mode read back due to wrong field offset.
    - Drop unused, but wrong define.
    - Fix issue with magnetometer scale an units.
   nxp,imx8qxp
    - Fix an irq flood due to not reading data early enough.
   st,lsm6dsx
    - Add CONFIG_IIO_TRIGGERED_BUFFER select.
   st,stm32-adc
    - Fix missing MODULE_DEVICE_TABLE() needed for module aliases.
   ti,twl6030
    - Fix missing enable of some channels.
    - Fix a typo in previous patch that meant one channel still wasn't enabled.
   xilinx,xadc
    - Carrying on incorrectly after allocation error."

* tag 'iio-fixes-for-6.2a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: imu: fxos8700: fix MAGN sensor scale and unit
  iio: imu: fxos8700: remove definition FXOS8700_CTRL_ODR_MIN
  iio: imu: fxos8700: fix failed initialization ODR mode assignment
  iio: imu: fxos8700: fix incorrect ODR mode readback
  iio: light: cm32181: Fix PM support on system with 2 I2C resources
  iio: hid: fix the retval in gyro_3d_capture_sample
  iio: hid: fix the retval in accel_3d_capture_sample
  iio: imu: st_lsm6dsx: fix build when CONFIG_IIO_TRIGGERED_BUFFER=m
  iio:adc:twl6030: Enable measurement of VAC
  iio: imu: fxos8700: fix ACCEL measurement range selection
  iio: imu: fxos8700: fix IMU data bits returned to user space
  iio: imu: fxos8700: fix incomplete ACCEL and MAGN channels readback
  iio: imu: fxos8700: fix swapped ACCEL and MAGN channels readback
  iio: imu: fxos8700: fix map label of channel type to MAGN sensor
  iio:adc:twl6030: Enable measurements of VUSB, VBAT and others
  iio: imx8qxp-adc: fix irq flood when call imx8qxp_adc_read_raw()
  iio: adc: xilinx-ams: fix devm_krealloc() return value check
  iio: adc: berlin2-adc: Add missing of_node_put() in error path
  iio: adc: stm32-dfsdm: fill module aliases

usb: early: xhci-dbc: Use memcpy_and_pad()

Instead of zeroing some memory and then copying data in part or all of it,
use memcpy_and_pad().
This avoids writing some memory twice and should save a few cycles.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b447a7e9778d3f9e6997eb9494f1687dc2d5d3bf.1675016180.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: early: xhci-dbc: Optimize early_xdbc_write()

There is no point in zeroing 'buf'.
It would be cleared only once, and if the 'while' loop is executed several
times, all but the first run would have a 'dirty' buffer.
Moreover, the size of the chunk is computed in the loop and this size is
passed to xdbc_bulk_write().

So remove this useless memset().

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/687bbcd940c59fbddd0e3a8b578fd3422962e50f.1675016180.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: early: xhci-dbc: Fix a potential out-of-bound memory access

If xdbc_bulk_write() fails, the values in 'buf' can be anything. So the
string is not guaranteed to be NULL terminated when xdbc_trace() is called.

Reserve an extra byte, which will be zeroed automatically because 'buf' is
a static variable, in order to avoid troubles, should it happen.

Fixes: aeb9dd1de98c ("usb/early: Add driver for xhci debug capability")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d6a7562c5e839a195cee85db6dc81817f9372cb1.1675016180.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings

Add binding documentation for the MT8365 SoC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
[bero@baylibre.com: Cleanups suggested by reviewers]
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230125143503.1015424-7-bero@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings

Add binding documentation for the MT8365 SoC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bernhard Rosenkränzer <bero@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230125143503.1015424-6-bero@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: chipidea: ci_hdrc_imx: use dev_err_probe

Add error message if finding USB PHY fails or is deferred.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230130094151.95174-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: fsa4480: Use generic node name

Node names should be generic. Change fsa4480@ to typec-mux@.

Fixes: 01afa882f12d ("dt-bindings: usb: Add binding for fcs,fsa4480")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230130113151.2130063-1-konrad.dybcio@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: phy: nop: Fix a typo ("specifiy")

Spell it correctly as "specify".

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230129124258.1295503-1-j.neuschaefer@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: samsung,exynos-dwc3: allow unit address in DTS

The Samsung Exynos SoC USB 3.0 DWC3 Controller is a simple wrapper of
actual DWC3 Controller device node.  It handles necessary Samsung
Exynos-specific resources (regulators, clocks), but does not have its
own MMIO address space.

However neither simple-bus bindings nor dtc W=1 accept device nodes in
soc@ node which do not have unit address.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230127211748.260718-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: fotg210: fix return value check in fotg210_probe()

devm_platform_get_and_ioremap_resource() never returns NULL pointer,
it will return ERR_PTR() when it fails, so replace the check with
IS_ERR().

Fixes: baef5330d35b ("usb: fotg210: Acquire memory resource in core")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230130120633.3342285-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: vialab,vl817: Cleanup compatible, reset-gpios and required

Cleanup by removing unneeded quotes from refs and
add maxItems to reset-gpios and fix the required list.

Fixes: 31360c28dfdd ("dt-bindings: usb: Add binding for Via lab VL817 hub controller")
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230130084744.2539-5-linux.amoon@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: MAX3421: Handle USB NAK correctly

A USB peripheral can respond with a NAK if it is not yet ready to
send/receive data. In this case, the transaction should be retried. The
MAX3421 driver did do this, and switched to a different type of retry
after a number of 'fast' retries. On at least some USB flash devices,
this second type of retry never succeeds. This patch changes the
behaviour so that 'fast' retries continue.

Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20230127024734.8777-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: usb: qcom,dwc3: allow required-opps

Few Qualcomm SoCs require minimum performance level of power domain, so
allow it:

  sm8550-mtp.dtb: usb@a6f8800: 'required-opps' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230127121122.342191-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sched: sch: Bounds check priority

Nothing was explicitly bounds checking the priority index used to access
clpriop[]. WARN and bail out early if it's pathological. Seen with GCC 13:

../net/sched/sch_htb.c: In function 'htb_activate_prios':
../net/sched/sch_htb.c:437:44: warning: array subscript [0, 31] is outside array bounds of 'struct htb_prio[8]' [-Warray-bounds=]
  437 |                         if (p->inner.clprio[prio].feed.rb_node)
      |                             ~~~~~~~~~~~~~~~^~~~~~
../net/sched/sch_htb.c:131:41: note: while referencing 'clprio'
  131 |                         struct htb_prio clprio[TC_HTB_NUMPRIO];
      |                                         ^~~~~~

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Link: https://lore.kernel.org/r/20230127224036.never.561-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

usg: gadget: Move validation out of lock in webusb_bcdVersion_store()

Validation has nothing to do with any protected data,
move it out of the lock and make code neater.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230127112638.84806-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: Use correct APIs and data types for UUID handling

We have two types for UUIDs depending on the byte ordering.
Instead of explaining how bytes should go over the wire,
use dedicated APIs and data types. This removes a confusion
over the byte ordering.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-By: Jó Ágila Bitsch <jgilab@gmail.com>
Link: https://lore.kernel.org/r/20230125143425.85268-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ethernet: mtk_eth_soc: Avoid truncating allocation

There doesn't appear to be a reason to truncate the allocation used for
flow_info, so do a full allocation and remove the unused empty struct.
GCC does not like having a reference to an object that has been
partially allocated, as bounds checking may become impossible when
such an object is passed to other code. Seen with GCC 13:

../drivers/net/ethernet/mediatek/mtk_ppe.c: In function 'mtk_foe_entry_commit_subflow':
../drivers/net/ethernet/mediatek/mtk_ppe.c:623:18: warning: array subscript 'struct mtk_flow_entry[0]' is partly outside array bounds of 'unsigned char[48]' [-Warray-bounds=]
  623 |         flow_info->l2_data.base_flow = entry;
      |                  ^~

Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Mark Lee <Mark-MC.Lee@mediatek.com>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230127223853.never.014-kees@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Documentation: usb: correct spelling

Correct spelling problems for Documentation/usb/ as reported
by codespell.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-usb@vger.kernel.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Link: https://lore.kernel.org/r/20230127064005.1558-33-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: modinst: Fix build error when CONFIG_MODULE_SIG_KEY is a PKCS#11 URI

When CONFIG_MODULE_SIG_KEY is PKCS#11 URI (pkcs11:*), signing of modules
fails:

  scripts/sign-file sha256 /.../linux/pkcs11:token=foo;object=bar;pin-value=1111 certs/signing_key.x509 /.../kernel/crypto/tcrypt.ko
  Usage: scripts/sign-file [-dp] <hash algo> <key> <x509> <module> [<dest>]
         scripts/sign-file -s <raw sig> <hash algo> <x509> <module> [<dest>]

First, we need to avoid adding the $(srctree)/ prefix to the URL.

Second, since the kconfig string values no longer include quotes, we need to add
them again when passing a PKCS#11 URI to sign-file. This avoids
splitting by the shell if the URI contains semicolons.

Fixes: 4db9c2e3d055 ("kbuild: stop using config_filename in scripts/Makefile.modsign")
Fixes: 129ab0d2d9f3 ("kbuild: do not quote string values in include/config/auto.conf")
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

certs: Fix build error when PKCS#11 URI contains semicolon

When CONFIG_MODULE_SIG_KEY is PKCS#11 URI (pkcs11:*) and contains a
semicolon, signing_key.x509 fails to build:

  certs/extract-cert pkcs11:token=foo;object=bar;pin-value=1111 certs/signing_key.x509
  Usage: extract-cert <source> <dest>

Add quotes to the extract-cert argument to avoid splitting by the shell.

This approach was suggested by Masahiro Yamada <masahiroy@kernel.org>.

Fixes: 129ab0d2d9f3 ("kbuild: do not quote string values in include/config/auto.conf")
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

usb: uvc: use v4l2_fill_fmtdesc instead of open coded format name

Since v4l2_fill_fmtdesc will be called in the ioctl v4l_enum_fmt anyway.
We can set the format description and compressed flag from v4l_fill_fmtdesc
and can remove the extra name field in uvc_format_desc.

Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20230126231456.3402323-6-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: uvc: make uvc_format_desc table const

Since the uvc_fmts array can not be modified we declare it const and
change every user of the uvc_format_by_guid function aswell.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-5-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: uvc: move uvc_fmts and uvc_format_by_guid to own compile unit

The media driver USB_VIDEO_CLASS and USB_F_UVC are using the same
function uvc_format_by_guid. Since the function is inline, every user
will get a copy of the used uvc_fmts array and the function. This patch
moves the code to an own compile unit and add this dependency as
UVC_COMMON to both users.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-4-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: uvc: move media/v4l2-uvc.h to usb/uvc.h

Since the headerfile is only used in usb devices it is better
placed with the other usb files.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Tested-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: uvcvideo: Add GUID for BGRA/X 8:8:8:8

The Cypress EZUSB FX3 UVC example can be configured to report pixel
format "e436eb7e-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGRA/X 8:8:8:8.

The UVC 1.5 spec [1] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[2]. This Media Format SDK defines this GUID as corresponding
to `MEDIASUBTYPE_RGB32`, which is confirmed by [4] as `MEDIASUBTYPE_ARGB32`
has different GUID.

Note that in my case, the FX3 UVC can output either channel order,
BGR or RGB or any other mix for that matter. Since Linux commit
1b8dc32286a1a ("[media] uvcvideo: Add GUID for BGR 8:8:8")
defined a GUID for `MEDIASUBTYPE_RGB24` channel order as BGR, keep
this change consistent and define `MEDIASUBTYPE_RGB32` as BGR as well.
Document [3] also indicates the channel order is BGR.

[1] https://www.usb.org/document-library/video-class-v15-document-set
[2] https://learn.microsoft.com/en-us/windows/win32/wmformat/media-type-identifiers
[3] https://learn.microsoft.com/en-us/windows/win32/directshow/uncompressed-rgb-video-subtypes
[4] https://gix.github.io/media-types/

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ricardo@ribalda.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20230126231456.3402323-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'media-uvc-next-20230115' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux into usb-next

Merge in this tag from the media tree so that future USB uvc patches
will apply properly.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'media-uvc-next-20230115' of git://git.kernel.org/pub/scm/linux/kernel/git/pinchartl/linux: (27 commits)
  media: uvcvideo: Silence memcpy() run-time false positive warnings
  media: uvcvideo: Quirk for autosuspend in Logitech B910 and C910
  media: uvcvideo: Fix race condition with usb_kill_urb
  media: uvcvideo: Use standard names for menus
  media: uvcvideo: Fix power line control for Lenovo Integrated Camera
  media: uvcvideo: Refactor power_line_frequency_controls_limited
  media: uvcvideo: Refactor uvc_ctrl_mappings_uvcXX
  media: uvcvideo: Implement mask for V4L2_CTRL_TYPE_MENU
  media: uvcvideo: Extend documentation of uvc_video_clock_decode()
  media: uvcvideo: Limit power line control for Acer EasyCamera
  media: uvcvideo: Refactor __uvc_ctrl_add_mapping
  media: uvcvideo: Fix handling on Bitmask controls
  media: uvcvideo: Do not return positive errors in uvc_query_ctrl()
  media: uvcvideo: Return -EACCES for Wrong state error
  media: uvcvideo: Improve error logging in uvc_query_ctrl()
  media: uvcvideo: Check for INACTIVE in uvc_ctrl_is_accessible()
  media: uvcvideo: Factor out usb_string() calls
  media: uvcvideo: Limit power line control for Acer EasyCamera
  media: uvcvideo: Recover stalled ElGato devices
  media: uvcvideo: Remove void casting for the status endpoint
  ...

ALSA: firewire-motu: fix unreleased lock warning in hwdep device

Smatch static analysis tool detects that acquired lock is not released
in hwdep device when condition branch is passed due to no event. It is
unlikely to occur, while fulfilling is preferable for better coding.

Reported-by: Dan Carpenter <error27@gmail.com>
Fixes: 634ec0b2906e ("ALSA: firewire-motu: notify event for parameter change in register DSP model")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230130141540.102854-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'ieee802154-for-net-2023-01-30' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
ieee802154 for net 2023-01-30

Only one fix this time around.

Miquel Raynal fixed a potential double free spotted by Dan Carpenter.

* tag 'ieee802154-for-net-2023-01-30' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
  mac802154: Fix possible double free upon parsing error
====================

Link: https://lore.kernel.org/r/20230130095646.301448-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net/tls: tls_is_tx_ready() checked list_entry

tls_is_tx_ready() checks that list_first_entry() does not return NULL.
This condition can never happen. For empty lists, list_first_entry()
returns the list_entry() of the head, which is a type confusion.
Use list_first_entry_or_null() which returns NULL in case of empty
lists.

Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Link: https://lore.kernel.org/r/20230128-list-entry-null-check-tls-v1-1-525bbfe6f0d0@diag.uniroma1.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-01-27 (ice)

This series contains updates to ice driver only.

Dave prevents modifying channels when RDMA is active as this will break
RDMA traffic.

Michal fixes a broken URL.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  ice: Fix broken link in ice NAPI doc
  ice: Prevent set_channel from changing queues while RDMA active
====================

Link: https://lore.kernel.org/r/20230127225333.1534783-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

powerpc/imc-pmu: Revert nest_init_lock to being a mutex

The recent commit 76d588dddc45 ("powerpc/imc-pmu: Fix use of mutex in
IRQs disabled section") fixed warnings (and possible deadlocks) in the
IMC PMU driver by converting the locking to use spinlocks.

It also converted the init-time nest_init_lock to a spinlock, even
though it's not used at runtime in IRQ disabled sections or while
holding other spinlocks.

This leads to warnings such as:

  BUG: sleeping function called from invalid context at include/linux/percpu-rwsem.h:49
  in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
  preempt_count: 1, expected: 0
  CPU: 7 PID: 1 Comm: swapper/0 Not tainted 6.2.0-rc2-14719-gf12cd06109f4-dirty #1
  Hardware name: Mambo,Simulated-System POWER9 0x4e1203 opal:v6.6.6 PowerNV
  Call Trace:
    dump_stack_lvl+0x74/0xa8 (unreliable)
    __might_resched+0x178/0x1a0
    __cpuhp_setup_state+0x64/0x1e0
    init_imc_pmu+0xe48/0x1250
    opal_imc_counters_probe+0x30c/0x6a0
    platform_probe+0x78/0x110
    really_probe+0x104/0x420
    __driver_probe_device+0xb0/0x170
    driver_probe_device+0x58/0x180
    __driver_attach+0xd8/0x250
    bus_for_each_dev+0xb4/0x140
    driver_attach+0x34/0x50
    bus_add_driver+0x1e8/0x2d0
    driver_register+0xb4/0x1c0
    __platform_driver_register+0x38/0x50
    opal_imc_driver_init+0x2c/0x40
    do_one_initcall+0x80/0x360
    kernel_init_freeable+0x310/0x3b8
    kernel_init+0x30/0x1a0
    ret_from_kernel_thread+0x5c/0x64

Fix it by converting nest_init_lock back to a mutex, so that we can call
sleeping functions while holding it. There is no interaction between
nest_init_lock and the runtime spinlocks used by the actual PMU routines.

Fixes: 76d588dddc45 ("powerpc/imc-pmu: Fix use of mutex in IRQs disabled section")
Tested-by: Kajol Jain<kjain@linux.ibm.com>
Reviewed-by: Kajol Jain<kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230130014401.540543-1-mpe@ellerman.id.au

drm/nouveau/acr/gm20b: regression fixes

Missed some Tegra-specific quirks when reworking ACR to support Ampere.

Fixes: 2541626cfb79 ("drm/nouveau/acr: use common falcon HS FW code for ACR FWs")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130223715.1831509-3-bskeggs@redhat.com

drm/nouveau/fb/tu102-: fix register used to determine scrub status

Turing apparently needs to use the same register we use on Ampere.

Not executing the scrubber ucode when required would result in large
areas of VRAM being inaccessible to the driver.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130223715.1831509-2-bskeggs@redhat.com

drm/nouveau/devinit/tu102-: wait for GFW_BOOT_PROGRESS == COMPLETED

Starting from Turing, the driver is no longer responsible for initiating
DEVINIT when required as the GPU started loading a FW image from ROM and
executing DEVINIT itself after power-on.

However - we apparently still need to wait for it to complete.

This should correct some issues with runpm on some systems, where we get
control of the HW before it's been fully reinitialised after resume from
suspend.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130223715.1831509-1-bskeggs@redhat.com

kunit: fix bug in KUNIT_EXPECT_MEMEQ

In KUNIT_EXPECT_MEMEQ and KUNIT_EXPECT_MEMNEQ, add check if one of the
inputs is NULL and fail if this is the case.

Currently, the kernel crashes if one of the inputs is NULL. Instead,
fail the test and add an appropriate error message.

Fixes: b8a926bea8b1 ("kunit: Introduce KUNIT_EXPECT_MEMEQ and KUNIT_EXPECT_MEMNEQ macros")
This was found by the kernel test robot:
https://lore.kernel.org/all/202212191448.D6EDPdOh-lkp@intel.com/

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rae Moar <rmoar@google.com>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>

drm/i915/adlp: Fix typo for reference clock

Fix typo for reference clock from 24400 to 24000.

Bspec: 55409
Fixes: 626426ff9ce4 ("drm/i915/adl_p: Add cdclk support for ADL-P")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230112094131.550252-1-chaitanya.kumar.borah@intel.com
(cherry picked from commit 2b6f7e39ccae065abfbe3b6e562ec95ccad09f1e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Fix potential bit_17 double-free

A userspace with multiple threads racing I915_GEM_SET_TILING to set the
tiling to I915_TILING_NONE could trigger a double free of the bit_17
bitmask.  (Or conversely leak memory on the transition to tiled.)  Move
allocation/free'ing of the bitmask within the section protected by the
obj lock.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes: 2850748ef876 ("drm/i915: Pull i915_vma_pin under the vm->mutex")
Cc: <stable@vger.kernel.org> # v5.5+
[tursulin: Correct fixes tag and added cc stable.]
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127200550.3531984-1-robdclark@gmail.com
(cherry picked from commit 10e0cbaaf1104f449d695c80bcacf930dcd3c42e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Fix up locking around dumping requests lists

The debugfs dump of requests was confused about what state requires
the execlist lock versus the GuC lock. There was also a bunch of
duplicated messy code between it and the error capture code.

So refactor the hung request search into a re-usable function. And
reduce the span of the execlist state lock to only the execlist
specific code paths. In order to do that, also move the report of hold
count (which is an execlist only concept) from the top level dump
function to the lower level execlist specific function. Also, move the
execlist specific code into the execlist source file.

v2: Rename some functions and move to more appropriate files (Daniele).
v3: Rename new execlist dump function (Daniele)

Fixes: dc0dad365c5e ("drm/i915/guc: Fix for error capture after full GPU reset with GuC")
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Michael Cheng <michael.cheng@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127002842.3169194-4-John.C.Harrison@Intel.com
(cherry picked from commit a4be3dca53172d9d2091e4b474fb795c81ed3d6c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Fix request ref counting during error capture & debugfs dump

When GuC support was added to error capture, the reference counting
around the request object was broken. Fix it up.

The context based search manages the spinlocking around the search
internally. So it needs to grab the reference count internally as
well. The execlist only request based search relies on external
locking, so it needs an external reference count but within the
spinlock not outside it.

The only other caller of the context based search is the code for
dumping engine state to debugfs. That code wasn't previously getting
an explicit reference at all as it does everything while holding the
execlist specific spinlock. So, that needs updaing as well as that
spinlock doesn't help when using GuC submission. Rather than trying to
conditionally get/put depending on submission model, just change it to
always do the get/put.

v2: Explicitly document adding an extra blank line in some dense code
(Andy Shevchenko). Fix multiple potential null pointer derefs in case
of no request found (some spotted by Tvrtko, but there was more!).
Also fix a leaked request in case of !started and another in
__guc_reset_context now that intel_context_find_active_request is
actually reference counting the returned request.
v3: Add a _get suffix to intel_context_find_active_request now that it
grabs a reference (Daniele).
v4: Split the intel_guc_find_hung_context change to a separate patch
and rename intel_context_find_active_request_get to
intel_context_get_active_request (Tvrtko).
v5: s/locking/reference counting/ in commit message (Tvrtko)

Fixes: dc0dad365c5e ("drm/i915/guc: Fix for error capture after full GPU reset with GuC")
Fixes: 573ba126aef3 ("drm/i915/guc: Capture error state on context reset")
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Michael Cheng <michael.cheng@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aravind Iddamsetty <aravind.iddamsetty@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127002842.3169194-3-John.C.Harrison@Intel.com
(cherry picked from commit 3700e353781e27f1bc7222f51f2cc36cbeb9b4ec)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915/guc: Fix locking when searching for a hung request

intel_guc_find_hung_context() was not acquiring the correct spinlock
before searching the request list. So fix that up. While at it, add
some extra whitespace padding for readability.

Fixes: dc0dad365c5e ("drm/i915/guc: Fix for error capture after full GPU reset with GuC")
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Michael Cheng <michael.cheng@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Bruce Chang <yu.bruce.chang@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127002842.3169194-2-John.C.Harrison@Intel.com
(cherry picked from commit d1c3717501bcf56536e8b8c1bdaf5cd5357f6bb2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

drm/i915: Avoid potential vm use-after-free

Adding the vm to the vm_xa table makes it visible to userspace, which
could try to race with us to close the vm.  So we need to take our extra
reference before putting it in the table.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Fixes: 9ec8795e7d91 ("drm/i915: Drop __rcu from gem_context->vm")
Cc: <stable@vger.kernel.org> # v5.16+
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230119173321.2825472-1-robdclark@gmail.com
(cherry picked from commit 99343c46d4e2b34c285d3d5f68ff04274c2f9fb4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Merge tag 'fscache-fixes-20230130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull fscache fixes from David Howells:
 "Fix two problems in fscache volume handling:

   - wake_up_bit() is incorrectly paired with wait_var_event(). The
     latter selects the waitqueue to use differently.

   - Missing barriers ordering between state bit and task state"

* tag 'fscache-fixes-20230130' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  fscache: Use clear_and_wake_up_bit() in fscache_create_volume_work()
  fscache: Use wait_on_bit() to wait for the freeing of relinquished volume

Merge tag 'imx-fixes-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 6.2, round 2:

- Update MAINTAINERS i.MX entry to match arm64 freescale DTS.
- Drop misused 'uart-has-rtscts' from imx8m-venice boards.
- Fix USB host over-current polarity for imx7d-smegw01 board.
- Fix a typo in i.MX8DXL sc_pwrkey property name.
- Fix GPIO watchdog property for i.MX8MM eDM SBC board.
- Keep Ethernet PHY powered on imx8mm-verdin to avoid kernel crash.
- Fix configuration of i.MX8MM pad UART1_DTE_RX.

* tag 'imx-fixes-6.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx7d-smegw01: Fix USB host over-current polarity
  arm64: dts: imx8mm-verdin: Do not power down eth-phy
  MAINTAINERS: match freescale ARM64 DT directory in i.MX entry
  arm64: dts: imx8mm: Fix pad control for UART1_DTE_RX
  arm64: dts: freescale: imx8dxl: fix sc_pwrkey's property name linux,keycode
  arm64: dts: imx8m-venice: Remove incorrect 'uart-has-rtscts'
  arm64: dts: imx8mm: Reinstate GPIO watchdog always-running property on eDM SBC

Link: https://lore.kernel.org/r/20230130003614.GP20713@T480
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sunxi-fixes-for-6.2-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes

- Fix error handling in RSB init

* tag 'sunxi-fixes-for-6.2-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  bus: sunxi-rsb: Fix error handling in sunxi_rsb_init()

Link: https://lore.kernel.org/r/Y9RWcDdO0nj98KVj@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

MAINTAINERS: amd: drop inactive Brijesh Singh

Emails to Brijesh Singh bounce ("550 5.1.10
RESOLVER.ADR.RecipientNotFound; Recipient not found by SMTP address
lookup").

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20230127105935.99174-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

watchdog: diag288_wdt: fix __diag288() inline assembly

The DIAG 288 statement consumes an EBCDIC string the address of which is
passed in a register. Use a "memory" clobber to tell the compiler that
memory is accessed within the inline assembly.

Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>

watchdog: diag288_wdt: do not use stack buffers for hardware data

With CONFIG_VMAP_STACK=y the stack is allocated from the vmalloc space.
Data passed to a hardware or a hypervisor interface that
requires V=R can no longer be allocated on the stack.

Use kmalloc() to get memory for a diag288 command.

Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>

platform/x86: thinkpad_acpi: Fix thinklight LED brightness returning 255

Reading the thinklight LED brightnes while the LED is on returns
255 (LED_FULL) but we advertise a max_brightness of 1, so this should
be 1 (LED_ON).

Fixes: db5e2a4ca0a7 ("platform/x86: thinkpad_acpi: Fix max_brightness of thinklight")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230127235723.412864-1-hdegoede@redhat.com

platform/x86/amd: pmc: add CONFIG_SERIO dependency

Using the serio subsystem now requires the code to be reachable:

x86_64-linux-ld: drivers/platform/x86/amd/pmc.o: in function `amd_pmc_suspend_handler':
pmc.c:(.text+0x86c): undefined reference to `serio_bus'

Add the usual dependency: as other users of serio use 'select'
rather than 'depends on', use the same here.

Fixes: 8e60615e8932 ("platform/x86/amd: pmc: Disable IRQ1 wakeup for RN/CZN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230127093950.2368575-1-arnd@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86/amd/pmf: Ensure mutexes are initialized before use

As soon as the first handler or sysfs file is registered
the mutex may get used.

Move the initialization to before any handler registration /
sysfs file creation.

Likewise move the destruction of the mutex to after all
the de-initialization is done.

Fixes: da5ce22df5fe ("platform/x86/amd/pmf: Add support for PMF core layer")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230130132554.696025-1-hdegoede@redhat.com

platform/x86/amd/pmf: Fix to update SPS thermals when power supply change

Every power mode of static power slider has its own AC and DC power
settings.

When the power source changes from AC to DC, corresponding DC thermals
were not updated from PMF config store and this leads the system to always
run on AC power settings.

Fix it by registering with power_supply notifier and apply DC settings
upon getting notified by the power_supply handler.

Fixes: da5ce22df5fe ("platform/x86/amd/pmf: Add support for PMF core layer")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-6-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86/amd/pmf: Fix to update SPS default pprof thermals

By design PMF static slider will be set to BALANCED during
init, but updating to corresponding thermal values from
the PMF config store was missed, leading to improper settings
getting propagated to PMFW.

Fixes: 4c71ae414474 ("platform/x86/amd/pmf: Add support SPS PMF feature")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-5-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86/amd/pmf: update to auto-mode limits only after AMT event

Auto-mode thermal limits should be updated only after receiving the AMT
event. But due to a bug in the older commit, these settings were getting
applied during the auto-mode init.

Fix this by removing amd_pmf_set_automode() during auto-mode
initialization.

Fixes: 3f5571d99524 ("platform/x86/amd/pmf: Add support for Auto mode feature")
Suggested-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-4-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86/amd/pmf: Add helper routine to check pprof is balanced

Add helper routine to check if the current platform profile
is balanced mode and remove duplicate code occurrences.

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-3-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

platform/x86/amd/pmf: Add helper routine to update SPS thermals

Add helper routine to update the static slider information
and remove the duplicate code occurrences after this change.

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230125095936.3292883-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

fscache: Use clear_and_wake_up_bit() in fscache_create_volume_work()

fscache_create_volume_work() uses wake_up_bit() to wake up the processes
which are waiting for the completion of volume creation. According to
comments in wake_up_bit() and waitqueue_active(), an extra smp_mb() is
needed to guarantee the memory order between FSCACHE_VOLUME_CREATING
flag and waitqueue_active() before invoking wake_up_bit().

Fixing it by using clear_and_wake_up_bit() to add the missing memory
barrier.

Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20230113115211.2895845-3-houtao@huaweicloud.com/

fscache: Use wait_on_bit() to wait for the freeing of relinquished volume

The freeing of relinquished volume will wake up the pending volume
acquisition by using wake_up_bit(), however it is mismatched with
wait_var_event() used in fscache_wait_on_volume_collision() and it will
never wake up the waiter in the wait-queue because these two functions
operate on different wait-queues.

According to the implementation in fscache_wait_on_volume_collision(),
if the wake-up of pending acquisition is delayed longer than 20 seconds
(e.g., due to the delay of on-demand fd closing), the first
wait_var_event_timeout() will timeout and the following wait_var_event()
will hang forever as shown below:

 FS-Cache: Potential volume collision new=00000024 old=00000022
 ......
 INFO: task mount:1148 blocked for more than 122 seconds.
       Not tainted 6.1.0-rc6+ #1
 task:mount           state:D stack:0     pid:1148  ppid:1
 Call Trace:
  <TASK>
  __schedule+0x2f6/0xb80
  schedule+0x67/0xe0
  fscache_wait_on_volume_collision.cold+0x80/0x82
  __fscache_acquire_volume+0x40d/0x4e0
  erofs_fscache_register_volume+0x51/0xe0 [erofs]
  erofs_fscache_register_fs+0x19c/0x240 [erofs]
  erofs_fc_fill_super+0x746/0xaf0 [erofs]
  vfs_get_super+0x7d/0x100
  get_tree_nodev+0x16/0x20
  erofs_fc_get_tree+0x20/0x30 [erofs]
  vfs_get_tree+0x24/0xb0
  path_mount+0x2fa/0xa90
  do_mount+0x7c/0xa0
  __x64_sys_mount+0x8b/0xe0
  do_syscall_64+0x30/0x60
  entry_SYSCALL_64_after_hwframe+0x46/0xb0

Considering that wake_up_bit() is more selective, so fix it by using
wait_on_bit() instead of wait_var_event() to wait for the freeing of
relinquished volume. In addition because waitqueue_active() is used in
wake_up_bit() and clear_bit() doesn't imply any memory barrier, use
clear_and_wake_up_bit() to add the missing memory barrier between
cursor->flags and waitqueue_active().

Fixes: 62ab63352350 ("fscache: Implement volume registration")
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20230113115211.2895845-2-houtao@huaweicloud.com/

net: phy: fix null dereference in phy_attach_direct

Commit bc66fa87d4fd ("net: phy: Add link between phy dev and mac dev")
introduced a link between net devices and phy devices. It fails to check
whether dev is NULL, leading to a NULL dereference error.

Fixes: bc66fa87d4fd ("net: phy: Add link between phy dev and mac dev")
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

powerpc/64: Fix perf profiling asynchronous interrupt handlers

Interrupt entry sets the soft mask to IRQS_ALL_DISABLED to match the
hard irq disabled state. So when should_hard_irq_enable() returns true
because we want PMI interrupts in irq handlers, MSR[EE] is enabled but
PMIs just get soft-masked. Fix this by clearing IRQS_PMI_DISABLED before
enabling MSR[EE].

This also tidies some of the warnings, no need to duplicate them in
both should_hard_irq_enable() and do_hard_irq_enable().

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230121100156.2824054-1-npiggin@gmail.com

powerpc/64s: Fix local irq disable when PMIs are disabled

When PMI interrupts are soft-masked, local_irq_save() will clear the PMI
mask bit, allowing PMIs in and causing a race condition. This causes a
deadlock in native_hpte_insert via hash_preload, which depends on PMIs
being disabled since commit 8b91cee5eadd ("powerpc/64s/hash: Make hash
faults work in NMI context"). native_hpte_insert calls local_irq_save().
It's possible the lpar hash code is also affected when tracing is
enabled because __trace_hcall_entry() calls local_irq_save().

Fix this by making arch_local_irq_save() _or_ the IRQS_DISABLED bit into
the mask.

This was found with the stress_hpt option with a kbuild workload running
together with `perf record -g`.

Fixes: f442d004806e ("powerpc/64s: Add support to mask perf interrupts and replay them")
Fixes: 8b91cee5eadd ("powerpc/64s/hash: Make hash faults work in NMI context")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Just take the fix without the new warning]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230121095352.2823517-1-npiggin@gmail.com

netrom: Fix use-after-free caused by accept on already connected socket

If you call listen() and accept() on an already connect()ed
AF_NETROM socket, accept() can successfully connect.
This is because when the peer socket sends data to sendmsg,
the skb with its own sk stored in the connected socket's
sk->sk_receive_queue is connected, and nr_accept() dequeues
the skb waiting in the sk->sk_receive_queue.

As a result, nr_accept() allocates and returns a sock with
the sk of the parent AF_NETROM socket.

And here use-after-free can happen through complex race conditions:
```
                  cpu0                                                     cpu1
                                                               1. socket_2 = socket(AF_NETROM)
                                                                        .
                                                                        .
                                                                  listen(socket_2)
                                                                  accepted_socket = accept(socket_2)
       2. socket_1 = socket(AF_NETROM)
            nr_create()    // sk refcount : 1
          connect(socket_1)
                                                               3. write(accepted_socket)
                                                                    nr_sendmsg()
                                                                    nr_output()
                                                                    nr_kick()
                                                                    nr_send_iframe()
                                                                    nr_transmit_buffer()
                                                                    nr_route_frame()
                                                                    nr_loopback_queue()
                                                                    nr_loopback_timer()
                                                                    nr_rx_frame()
                                                                    nr_process_rx_frame(sk, skb);    // sk : socket_1's sk
                                                                    nr_state3_machine()
                                                                    nr_queue_rx_frame()
                                                                    sock_queue_rcv_skb()
                                                                    sock_queue_rcv_skb_reason()
                                                                    __sock_queue_rcv_skb()
                                                                    __skb_queue_tail(list, skb);    // list : socket_1's sk->sk_receive_queue
       4. listen(socket_1)
            nr_listen()
          uaf_socket = accept(socket_1)
            nr_accept()
            skb_dequeue(&sk->sk_receive_queue);
                                                               5. close(accepted_socket)
                                                                    nr_release()
                                                                    nr_write_internal(sk, NR_DISCREQ)
                                                                    nr_transmit_buffer()    // NR_DISCREQ
                                                                    nr_route_frame()
                                                                    nr_loopback_queue()
                                                                    nr_loopback_timer()
                                                                    nr_rx_frame()    // sk : socket_1's sk
                                                                    nr_process_rx_frame()  // NR_STATE_3
                                                                    nr_state3_machine()    // NR_DISCREQ
                                                                    nr_disconnect()
                                                                    nr_sk(sk)->state = NR_STATE_0;
       6. close(socket_1)    // sk refcount : 3
            nr_release()    // NR_STATE_0
            sock_put(sk);    // sk refcount : 0
            sk_free(sk);
          close(uaf_socket)
            nr_release()
            sock_hold(sk);    // UAF
```

KASAN report by syzbot:
```
BUG: KASAN: use-after-free in nr_release+0x66/0x460 net/netrom/af_netrom.c:520
Write of size 4 at addr ffff8880235d8080 by task syz-executor564/5128

Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xd1/0x138 lib/dump_stack.c:106
 print_address_description mm/kasan/report.c:306 [inline]
 print_report+0x15e/0x461 mm/kasan/report.c:417
 kasan_report+0xbf/0x1f0 mm/kasan/report.c:517
 check_region_inline mm/kasan/generic.c:183 [inline]
 kasan_check_range+0x141/0x190 mm/kasan/generic.c:189
 instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
 atomic_fetch_add_relaxed include/linux/atomic/atomic-instrumented.h:116 [inline]
 __refcount_add include/linux/refcount.h:193 [inline]
 __refcount_inc include/linux/refcount.h:250 [inline]
 refcount_inc include/linux/refcount.h:267 [inline]
 sock_hold include/net/sock.h:775 [inline]
 nr_release+0x66/0x460 net/netrom/af_netrom.c:520
 __sock_release+0xcd/0x280 net/socket.c:650
 sock_close+0x1c/0x20 net/socket.c:1365
 __fput+0x27c/0xa90 fs/file_table.c:320
 task_work_run+0x16f/0x270 kernel/task_work.c:179
 exit_task_work include/linux/task_work.h:38 [inline]
 do_exit+0xaa8/0x2950 kernel/exit.c:867
 do_group_exit+0xd4/0x2a0 kernel/exit.c:1012
 get_signal+0x21c3/0x2450 kernel/signal.c:2859
 arch_do_signal_or_restart+0x79/0x5c0 arch/x86/kernel/signal.c:306
 exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
 exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
 __syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
 syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
 do_syscall_64+0x46/0xb0 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7f6c19e3c9b9
Code: Unable to access opcode bytes at 0x7f6c19e3c98f.
RSP: 002b:00007fffd4ba2ce8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: 0000000000000116 RBX: 0000000000000003 RCX: 00007f6c19e3c9b9
RDX: 0000000000000318 RSI: 00000000200bd000 RDI: 0000000000000006
RBP: 0000000000000003 R08: 000000000000000d R09: 000000000000000d
R10: 0000000000000000 R11: 0000000000000246 R12: 000055555566a2c0
R13: 0000000000000011 R14: 0000000000000000 R15: 0000000000000000
 </TASK>

Allocated by task 5128:
 kasan_save_stack+0x22/0x40 mm/kasan/common.c:45
 kasan_set_track+0x25/0x30 mm/kasan/common.c:52
 ____kasan_kmalloc mm/kasan/common.c:371 [inline]
 ____kasan_kmalloc mm/kasan/common.c:330 [inline]
 __kasan_kmalloc+0xa3/0xb0 mm/kasan/common.c:380
 kasan_kmalloc include/linux/kasan.h:211 [inline]
 __do_kmalloc_node mm/slab_common.c:968 [inline]
 __kmalloc+0x5a/0xd0 mm/slab_common.c:981
 kmalloc include/linux/slab.h:584 [inline]
 sk_prot_alloc+0x140/0x290 net/core/sock.c:2038
 sk_alloc+0x3a/0x7a0 net/core/sock.c:2091
 nr_create+0xb6/0x5f0 net/netrom/af_netrom.c:433
 __sock_create+0x359/0x790 net/socket.c:1515
 sock_create net/socket.c:1566 [inline]
 __sys_socket_create net/socket.c:1603 [inline]
 __sys_socket_create net/socket.c:1588 [inline]
 __sys_socket+0x133/0x250 net/socket.c:1636
 __do_sys_socket net/socket.c:1649 [inline]
 __se_sys_socket net/socket.c:1647 [inline]
 __x64_sys_socket+0x73/0xb0 net/socket.c:1647
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Freed by task 5128:
 kasan_save_stack+0x22/0x40 mm/kasan/common.c:45
 kasan_set_track+0x25/0x30 mm/kasan/common.c:52
 kasan_save_free_info+0x2b/0x40 mm/kasan/generic.c:518
 ____kasan_slab_free mm/kasan/common.c:236 [inline]
 ____kasan_slab_free+0x13b/0x1a0 mm/kasan/common.c:200
 kasan_slab_free include/linux/kasan.h:177 [inline]
 __cache_free mm/slab.c:3394 [inline]
 __do_kmem_cache_free mm/slab.c:3580 [inline]
 __kmem_cache_free+0xcd/0x3b0 mm/slab.c:3587
 sk_prot_free net/core/sock.c:2074 [inline]
 __sk_destruct+0x5df/0x750 net/core/sock.c:2166
 sk_destruct net/core/sock.c:2181 [inline]
 __sk_free+0x175/0x460 net/core/sock.c:2192
 sk_free+0x7c/0xa0 net/core/sock.c:2203
 sock_put include/net/sock.h:1991 [inline]
 nr_release+0x39e/0x460 net/netrom/af_netrom.c:554
 __sock_release+0xcd/0x280 net/socket.c:650
 sock_close+0x1c/0x20 net/socket.c:1365
 __fput+0x27c/0xa90 fs/file_table.c:320
 task_work_run+0x16f/0x270 kernel/task_work.c:179
 exit_task_work include/linux/task_work.h:38 [inline]
 do_exit+0xaa8/0x2950 kernel/exit.c:867
 do_group_exit+0xd4/0x2a0 kernel/exit.c:1012
 get_signal+0x21c3/0x2450 kernel/signal.c:2859
 arch_do_signal_or_restart+0x79/0x5c0 arch/x86/kernel/signal.c:306
 exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
 exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
 __syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
 syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
 do_syscall_64+0x46/0xb0 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x63/0xcd
```

To fix this issue, nr_listen() returns -EINVAL for sockets that
successfully nr_connect().

Reported-by: syzbot+caa188bdfc1eeafeb418@syzkaller.appspotmail.com
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: do not stop RX_CLK in Rx LPI state for qcs404 SoC

Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.

Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.

Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

powerpc/kvm: Fix unannotated intra-function call warning

objtool throws the following warning:
  arch/powerpc/kvm/booke.o: warning: objtool: kvmppc_fill_pt_regs+0x30:
  unannotated intra-function call

Fix the warning by setting the value of 'nip' using the _THIS_IP_ macro,
without using an assembly bl/mflr sequence to save the instruction
pointer.

Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sathvika Vasireddy <sv@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230128124158.1066251-1-sv@linux.ibm.com

powerpc/85xx: Fix unannotated intra-function call warning

objtool throws the following warning:
  arch/powerpc/kernel/head_85xx.o: warning: objtool: .head.text+0x1a6c:
  unannotated intra-function call

Fix the warning by annotating KernelSPE symbol with SYM_FUNC_START_LOCAL
and SYM_FUNC_END macros.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sathvika Vasireddy <sv@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230128124138.1066176-1-sv@linux.ibm.com

block, bfq: fix uaf for bfqq in bic_set_bfqq()

After commit 64dc8c732f5c ("block, bfq: fix possible uaf for 'bfqq->bic'"),
bic->bfqq will be accessed in bic_set_bfqq(), however, in some context
bic->bfqq will be freed, and bic_set_bfqq() is called with the freed
bic->bfqq.

Fix the problem by always freeing bfqq after bic_set_bfqq().

Fixes: 64dc8c732f5c ("block, bfq: fix possible uaf for 'bfqq->bic'")
Reported-and-tested-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230130014136.591038-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Linux 6.2-rc6

Merge tag 'irq_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq fix from Borislav Petkov:

 - Cleanup the firmware node for the new IRQ MSI domain properly, to
   avoid leaking memory

* tag 'irq_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/msi: Free the fwnode created by msi_create_device_irq_domain()

Merge tag 'x86_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull x86 fixes from Borislav Petkov:

 - Start checking for -mindirect-branch-cs-prefix clang support too now
   that LLVM 16 will support it

 - Fix a NULL ptr deref when suspending with Xen PV

 - Have a SEV-SNP guest check explicitly for features enabled by the
   hypervisor and fail gracefully if some are unsupported by the guest
   instead of failing in a non-obvious and hard-to-debug way

 - Fix a MSI descriptor leakage under Xen

 - Mark Xen's MSI domain as supporting MSI-X

 - Prevent legacy PIC interrupts from being resent in software by
   marking them level triggered, as they should be, which lead to a NULL
   ptr deref

* tag 'x86_urgent_for_v6.2_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/build: Move '-mindirect-branch-cs-prefix' out of GCC-only block
  acpi: Fix suspend with Xen PV
  x86/sev: Add SEV-SNP guest feature negotiation support
  x86/pci/xen: Fixup fallout from the PCI/MSI overhaul
  x86/pci/xen: Set MSI_FLAG_PCI_MSIX support in Xen MSI domain
  x86/i8259: Mark legacy PIC interrupts with IRQ_LEVEL

Merge tag 'input-for-v6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input fixes from Dmitry Torokhov:

 - touchpads on HP 15-* laptops switched back to PS/2 emulation mode

 - a quirk for Clevo PCX0DX/TUXEDO XP1511 to make sure keyboard is
   responding after resume

* tag 'input-for-v6.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add Clevo PCX0DX to i8042 quirk table
  Revert "Input: synaptics - switch touchpad on HP Laptop 15-da3001TU to RMI mode"

KVM: selftests: aarch64: Test read-only PT memory regions

Extend the read-only memslot tests in page_fault_test to test
read-only PT (Page table) memslots. Note that this was not allowed
before commit 406504c7b040 ("KVM: arm64: Fix S1PTW handling on RO
memslots") as all S1PTW faults were treated as writes which resulted
in an (unrecoverable) exception inside the guest.

Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-5-ricarkol@google.com

KVM: selftests: aarch64: Fix check of dirty log PT write

The dirty log checks are mistakenly testing the first page in the page
table (PT) memory region instead of the page holding the test data
page PTE.  This wasn't an issue before commit 406504c7b040 ("KVM:
arm64: Fix S1PTW handling on RO memslots") as all PT pages (including
the first page) were treated as writes.

Fix the page_fault_test dirty logging tests by checking for the right
page: the one for the PTE of the data test page.

Fixes: a4edf25b3e25 ("KVM: selftests: aarch64: Add dirty logging tests into page_fault_test")
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-4-ricarkol@google.com

KVM: selftests: aarch64: Do not default to dirty PTE pages on all S1PTWs

Only Stage1 Page table walks (S1PTW) trying to write into a PTE should
result in the PTE page being dirty in the log.  However, the dirty log
tests in page_fault_test default to treat all S1PTW accesses as writes.
Fix the relevant tests by asserting dirty pages only for S1PTW writes,
which in these tests only applies to when Hardware management of the Access
Flag is enabled.

Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-3-ricarkol@google.com

KVM: selftests: aarch64: Relax userfaultfd read vs. write checks

Only Stage1 Page table walks (S1PTW) writing a PTE on an unmapped page
should result in a userfaultfd write. However, the userfaultfd tests in
page_fault_test wrongly assert that any S1PTW is a PTE write.

Fix this by relaxing the read vs. write checks in all userfaultfd
handlers.  Note that this is also an attempt to focus less on KVM (and
userfaultfd) behavior, and more on architectural behavior. Also note
that after commit 406504c7b040 ("KVM: arm64: Fix S1PTW handling on RO
memslots"), the userfaultfd fault (S1PTW with AF on an unmaped PTE
page) is actually a read: the translation fault that comes before the
permission fault.

Signed-off-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230127214353.245671-2-ricarkol@google.com

Merge tag 'cxl-fixes-for-6.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl

Pull cxl fixes from Dan Williams:
 "A couple of fixes for bugs introduced during the merge window. One is
  a regression, the other was a bug in the CXL AER handler:

   - Fix a crash regression due to module load order of cxl_pmem.ko

   - Fix wrong register offset read in CXL AER handling path"

* tag 'cxl-fixes-for-6.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/pmem: Fix nvdimm unregistration when cxl_pmem driver is absent
  cxl: fix cxl_report_and_clear() RAS UE addr mis-assignment

KVM: arm64: Allow no running vcpu on saving vgic3 pending table

We don't have a running VCPU context to save vgic3 pending table due
to KVM_DEV_ARM_VGIC_{GRP_CTRL, SAVE_PENDING_TABLES} command on KVM
device "kvm-arm-vgic-v3". The unknown case is caught by kvm-unit-tests.

   # ./kvm-unit-tests/tests/its-pending-migration
   WARNING: CPU: 120 PID: 7973 at arch/arm64/kvm/../../../virt/kvm/kvm_main.c:3325 \
   mark_page_dirty_in_slot+0x60/0xe0
    :
   mark_page_dirty_in_slot+0x60/0xe0
   __kvm_write_guest_page+0xcc/0x100
   kvm_write_guest+0x7c/0xb0
   vgic_v3_save_pending_tables+0x148/0x2a0
   vgic_set_common_attr+0x158/0x240
   vgic_v3_set_attr+0x4c/0x5c
   kvm_device_ioctl+0x100/0x160
   __arm64_sys_ioctl+0xa8/0xf0
   invoke_syscall.constprop.0+0x7c/0xd0
   el0_svc_common.constprop.0+0x144/0x160
   do_el0_svc+0x34/0x60
   el0_svc+0x3c/0x1a0
   el0t_64_sync_handler+0xb4/0x130
   el0t_64_sync+0x178/0x17c

Use vgic_write_guest_lock() to save vgic3 pending table.

Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230126235451.469087-5-gshan@redhat.com

KVM: arm64: Allow no running vcpu on restoring vgic3 LPI pending status

We don't have a running VCPU context to restore vgic3 LPI pending status
due to command KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_RESTORE_TABLES} on KVM
device "kvm-arm-vgic-its".

Use vgic_write_guest_lock() to restore vgic3 LPI pending status.

Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230126235451.469087-4-gshan@redhat.com

KVM: arm64: Add helper vgic_write_guest_lock()

Currently, the unknown no-running-vcpu sites are reported when a
dirty page is tracked by mark_page_dirty_in_slot(). Until now, the
only known no-running-vcpu site is saving vgic/its tables through
KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_SAVE_TABLES} command on KVM device
"kvm-arm-vgic-its". Unfortunately, there are more unknown sites to
be handled and no-running-vcpu context will be allowed in these
sites: (1) KVM_DEV_ARM_{VGIC_GRP_CTRL, ITS_RESTORE_TABLES} command
on KVM device "kvm-arm-vgic-its" to restore vgic/its tables. The
vgic3 LPI pending status could be restored. (2) Save vgic3 pending
table through KVM_DEV_ARM_{VGIC_GRP_CTRL, VGIC_SAVE_PENDING_TABLES}
command on KVM device "kvm-arm-vgic-v3".

In order to handle those unknown cases, we need a unified helper
vgic_write_guest_lock(). struct vgic_dist::save_its_tables_in_progress
is also renamed to struct vgic_dist::save_tables_in_progress.

No functional change intended.

Suggested-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230126235451.469087-3-gshan@redhat.com

Revert "mm/compaction: fix set skip in fast_find_migrateblock"

This reverts commit 7efc3b7261030da79001c00d92bc3392fd6c664c.

We have got openSUSE reports (Link 1) for 6.1 kernel with khugepaged
stalling CPU for long periods of time.  Investigation of tracepoint data
shows that compaction is stuck in repeating fast_find_migrateblock()
based migrate page isolation, and then fails to migrate all isolated
pages.

Commit 7efc3b726103 ("mm/compaction: fix set skip in fast_find_migrateblock")
was suspected as it was merged in 6.1 and in theory can indeed remove a
termination condition for fast_find_migrateblock() under certain
conditions, as it removes a place that always marks a scanned pageblock
from being re-scanned.  There are other such places, but those can be
skipped under certain conditions, which seems to match the tracepoint
data.

Testing of revert also appears to have resolved the issue, thus revert
the commit until a more robust solution for the original problem is
developed.

It's also likely this will fix qemu stalls with 6.1 kernel reported in
Link 2, but that is not yet confirmed.

Link: https://bugzilla.suse.com/show_bug.cgi?id=1206848
Link: https://lore.kernel.org/kvm/b8017e09-f336-3035-8344-c549086c2340@kernel.org/
Link: https://lore.kernel.org/lkml/20230125134434.18017-1-mgorman@techsingularity.net/
Fixes: 7efc3b726103 ("mm/compaction: fix set skip in fast_find_migrateblock")
Cc: <stable@vger.kernel.org>
Tested-by: Pedro Falcato <pedro.falcato@gmail.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix up more non-executable files marked executable

Joe found another DT file that shouldn't be executable, and that
frustrated me enough that I went hunting with this script:

    git ls-files -s |
        grep '^100755' |
        cut -f2 |
        xargs grep -L '^#!'

and that found another file that shouldn't have been marked executable
either, despite being in the scripts directory.

Maybe these two are the last ones at least for now.  But I'm sure we'll
be back in a few years, fixing things up again.

Fixes: 8c6789f4e2d4 ("ASoC: dt-bindings: Add Everest ES8326 audio CODEC")
Fixes: 4d8e5cd233db ("locking/atomics: Fix scripts/atomic/ script permissions")
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag '6.2-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd

Pull ksmbd server fixes from Steve French:
 "Four smb3 server fixes, all also for stable:

   - fix for signing bug

   - fix to more strictly check packet length

   - add a max connections parm to limit simultaneous connections

   - fix error message flood that can occur with newer Samba xattr
     format"

* tag '6.2-rc5-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
  ksmbd: downgrade ndr version error message to debug
  ksmbd: limit pdu length size according to connection status
  ksmbd: do not sign response to session request for guest login
  ksmbd: add max connections parameter

Merge tag 'fpga-for-6.2-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-linus

Xy writes:
   FPGA Manager changes for 6.2-final
   stratix10-soc:
     - Zheng's change fixes return value check
   Intel m10 bmc secure update:
     - Ilpo's change fixes probe rollback

   All patches have been reviewed on the mailing list, and have been in
   the last linux-next releases (as part of our for-6.2 branch)

Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-6.2-final' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
  fpga: m10bmc-sec: Fix probe rollback
  fpga: stratix10-soc: Fix return value check in s10_ops_write_init()

selftest: net: Improve IPV6_TCLASS/IPV6_HOPLIMIT tests apparmor compatibility

"tcpdump" is used to capture traffic in these tests while using a random,
temporary and not suffixed file for it. This can interfere with apparmor
configuration where the tool is only allowed to read from files with
'known' extensions.

The MINE type application/vnd.tcpdump.pcap was registered with IANA for
pcap files and .pcap is the extension that is both most common but also
aligned with standard apparmor configurations. See TCPDUMP(8) for more
details.

This improves compatibility with standard apparmor configurations by
using ".pcap" as the file extension for the tests' temporary files.

Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nvmem: qcom-spmi-sdam: fix module autoloading

Add the missing module device table so that the driver can be autoloaded
when built as a module.

Fixes: 40ce9798794f ("nvmem: add QTI SDAM driver")
Cc: stable@vger.kernel.org # 5.6
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-11-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: fix return value

Dan Carpenter points out that the return code was not set in commit
60c8b4aebd8e ("nvmem: core: fix cleanup after dev_set_name()"), but
this is not the only issue - we also need to zero wp_gpio to prevent
gpiod_put() being called on an error value.

Fixes: 560181d3ace6 ("nvmem: core: fix cleanup after dev_set_name()")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-10-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: fix cell removal on error

nvmem_add_cells() could return an error after some cells are already
added to the provider. In this case, the added cells are not removed.
Remove any registered cells if nvmem_add_cells() fails.

Fixes: fa72d847d68d7 ("nvmem: check the return value of nvmem_add_cells()")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-9-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: fix device node refcounting

In of_nvmem_cell_get(), of_get_next_parent() is used on cell_np. This
will decrement the refcount on cell_np, but cell_np is still used later
in the code. Use of_get_parent() instead and of_node_put() in the
appropriate places.

Fixes: 69aba7948cbe ("nvmem: Add a simple NVMEM framework for consumers")
Fixes: 7ae6478b304b ("nvmem: core: rework nvmem cell instance creation")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-8-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: fix registration vs use race

The i.MX6 CPU frequency driver sometimes fails to register at boot time
due to nvmem_cell_read_u32() sporadically returning -ENOENT.

This happens because there is a window where __nvmem_device_get() in
of_nvmem_cell_get() is able to return the nvmem device, but as cells
have been setup, nvmem_find_cell_entry_by_node() returns NULL.

The occurs because the nvmem core registration code violates one of the
fundamental principles of kernel programming: do not publish data
structures before their setup is complete.

Fix this by making nvmem core code conform with this principle.

Fixes: eace75cfdcf7 ("nvmem: Add a simple NVMEM framework for nvmem providers")
Cc: stable@vger.kernel.org
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-7-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: fix cleanup after dev_set_name()

If dev_set_name() fails, we leak nvmem->wp_gpio as the cleanup does not
put this. While a minimal fix for this would be to add the gpiod_put()
call, we can do better if we split device_register(), and use the
tested nvmem_release() cleanup code by initialising the device early,
and putting the device.

This results in a slightly larger fix, but results in clear code.

Note: this patch depends on "nvmem: core: initialise nvmem->id early"
and "nvmem: core: remove nvmem_config wp_gpio".

Fixes: 5544e90c8126 ("nvmem: core: add error handling for dev_set_name")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
[Srini: Fixed subject line and error code handing with wp_gpio while applying.]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-6-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: remove nvmem_config wp_gpio

No one provides wp_gpio, so let's remove it to avoid issues with
the nvmem core putting this gpio.

Cc: stable@vger.kernel.org
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-5-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: core: initialise nvmem->id early

The error path for wp_gpio attempts to free the IDA nvmem->id, but
this has yet to be assigned, so will always be zero - leaking the
ID allocated by ida_alloc(). Fix this by moving the initialisation
of nvmem->id earlier.

Fixes: f7d8d7dcd978 ("nvmem: fix memory leak in error path")
Cc: stable@vger.kernel.org
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-4-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: sunxi_sid: Always use 32-bit MMIO reads

The SID SRAM on at least some SoCs (A64 and D1) returns different values
when read with bus cycles narrower than 32 bits. This is not immediately
obvious, because memcpy_fromio() uses word-size accesses as long as
enough data is being copied.

The vendor driver always uses 32-bit MMIO reads, so do the same here.
This is faster than the register-based method, which is currently used
as a workaround on A64. And it fixes the values returned on D1, where
the SRAM method was being used.

The special case for the last word is needed to maintain .word_size == 1
for sysfs ABI compatibility, as noted previously in commit de2a3eaea552
("nvmem: sunxi_sid: Optimize register read-out method").

Fixes: 07ae4fde9efa ("nvmem: sunxi_sid: Add support for D1 variant")
Cc: stable@vger.kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: brcm_nvram: Add check for kzalloc

Add the check for the return value of kzalloc in order to avoid
NULL pointer dereference.

Fixes: 6e977eaa8280 ("nvmem: brcm_nvram: parse NVRAM content into NVMEM cells")
Cc: stable@vger.kernel.org
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230127104015.23839-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge branch 't7xx-pm-fixes'

Kornel Dulęba says:

====================
net: wwan: t7xx: Fix Runtime PM implementation

d10b3a695ba0 ("net: wwan: t7xx: Runtime PM") introduced support for
Runtime PM for this driver, but due to a bug in the initialization logic
the usage refcount would never reach 0, leaving the feature unused.
This patchset addresses that, together with a bug found after runtime
suspend was enabled.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: wwan: t7xx: Fix Runtime PM initialization

For PCI devices the Runtime PM refcount is incremented twice:
1. During device enumeration with a call to pm_runtime_forbid.
2. Just before a driver probe logic is called.
Because of that in order to enable Runtime PM on a given device
we have to call both pm_runtime_allow and pm_runtime_put_noidle,
once it's ready to be runtime suspended.
The former was missing causing the pm refcount to never reach 0.

Fixes: d10b3a695ba0 ("net: wwan: t7xx: Runtime PM")
Signed-off-by: Kornel Dulęba <mindal@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: wwan: t7xx: Fix Runtime PM resume sequence

Resume device before calling napi_schedule, instead of doing in the napi
poll routine. Polling is done in softrq context. We can't call the PM
resume logic from there as it's blocking and not irq safe.
In order to make it work modify the interrupt handler to be run from irq
handler thread.

Fixes: 5545b7b9f294 ("net: wwan: t7xx: Add NAPI support")
Signed-off-by: Kornel Dulęba <mindal@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mctp: purge receive queues on sk destruction

We may have pending skbs in the receive queue when the sk is being
destroyed; add a destructor to purge the queue.

MCTP doesn't use the error queue, so only the receive_queue is purged.

Fixes: 833ef3b91de6 ("mctp: Populate socket implementation")
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230126064551.464468-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

net: phy: dp83822: Fix null pointer access on DP83825/DP83826 devices

The probe() function is only used for the DP83822 PHY, leaving the
private data pointer uninitialized for the smaller DP83825/26 models.
While all uses of the private data structure are hidden in 82822 specific
callbacks, configuring the interrupt is shared across all models.
This causes a NULL pointer dereference on the smaller PHYs as it accesses
the private data unchecked. Verifying the pointer avoids that.

Fixes: 5dc39fd5ef35 ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Andre Kalb <andre.kalb@sma.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/Y9FzniUhUtbaGKU7@pc6682
Signed-off-by: Jakub Kicinski <kuba@kernel.org>