David Ahern [Wed, 24 Jan 2024 21:41:16 +0000 (14:41 -0700)]
selftest: Fix set of ping_group_range in fcnal-test
ping_group_range sysctl has a compound value which does not go
through the various function layers in tact. Create a helper
function to bypass the layers and correctly set the value.
David Ahern [Wed, 24 Jan 2024 21:41:15 +0000 (14:41 -0700)]
selftest: Update PATH for nettest in fcnal-test
Allow fcnal-test.sh to be run from top level directory in the
kernel repo as well as from tools/testing/selftests/net by
setting the PATH to find the in-tree nettest.
Jakub Kicinski [Fri, 26 Jan 2024 00:49:55 +0000 (16:49 -0800)]
Merge tag 'wireless-next-2024-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The first "new features" pull request for v6.9. We have only driver
changes this time and most of them are for Realtek drivers. Really
nice to see activity in Broadcom drivers again.
Major changes:
rtwl8xxxu
* RTL8188F: concurrent interface support
* Channel Switch Announcement (CSA) support in AP mode
brcmfmac
* per-vendor feature support
* per-vendor SAE password setup
rtlwifi
* speed up USB firmware initialisation
* tag 'wireless-next-2024-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (105 commits)
wifi: iwlegacy: Use kcalloc() instead of kzalloc()
wifi: rtw89: fix disabling concurrent mode TX hang issue
wifi: rtw89: fix HW scan timeout due to TSF sync issue
wifi: rtw89: add wait/completion for abort scan
wifi: rtw89: fix null pointer access when abort scan
wifi: rtw89: disable RTS when broadcast/multicast
wifi: rtw89: Set default CQM config if not present
wifi: rtw89: refine hardware scan C2H events
wifi: rtw89: refine add_chan H2C command to encode_bits
wifi: rtw89: 8922a: add BTG functions to assist BT coexistence to control TX/RX
wifi: rtw89: 8922a: add TX power related ops
wifi: rtw89: 8922a: add register definitions of H2C, C2H, page, RRSR and EDCCA
wifi: rtw89: 8922a: add chip_ops related to BB init
wifi: rtw89: 8922a: add chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add mlo_dbcc_mode for WiFi 7 chips
wifi: rtlwifi: Speed up firmware loading for USB
wifi: rtl8xxxu: add missing number of sec cam entries for all variants
wifi: brcmfmac: allow per-vendor event handling
wifi: brcmfmac: avoid invalid list operation when vendor attach fails
wifi: brcmfmac: Demote vendor-specific attach/detach messages to info
...
====================
Pedro Tammela [Wed, 24 Jan 2024 18:19:32 +0000 (15:19 -0300)]
selftests: tc-testing: enable all tdc tests
For the longest time tdc ran only actions and qdiscs tests.
It's time to enable all the remaining tests so every user visible
piece of TC is tested by the downstream CIs.
Pedro Tammela [Wed, 24 Jan 2024 18:19:30 +0000 (15:19 -0300)]
selftests: tc-testing: check if 'jq' is available in taprio tests
If 'jq' is not available the taprio tests might enter an infinite loop,
use the "dependsOn" feature from tdc to check if jq is present. If it's
not the test is skipped.
Linus Torvalds [Thu, 25 Jan 2024 18:58:35 +0000 (10:58 -0800)]
Merge tag 'net-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf, netfilter and WiFi.
Jakub is doing a lot of work to include the self-tests in our CI, as a
result a significant amount of self-tests related fixes is flowing in
(and will likely continue in the next few weeks).
Current release - regressions:
- bpf: fix a kernel crash for the riscv 64 JIT
- bnxt_en: fix memory leak in bnxt_hwrm_get_rings()
- revert "net: macsec: use skb_ensure_writable_head_tail to expand
the skb"
Previous releases - regressions:
- core: fix removing a namespace with conflicting altnames
- tcp:
- make sure init the accept_queue's spinlocks once
- fix autocork on CPUs with weak memory model
- udp: fix busy polling
- mlx5e:
- fix out-of-bound read in port timestamping
- fix peer flow lists corruption
- iwlwifi: fix a memory corruption
Previous releases - always broken:
- netfilter:
- nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress
basechain
- nft_limit: reject configurations that cause integer overflow
- bpf: fix bpf_xdp_adjust_tail() with XSK zero-copy mbuf, avoiding a
NULL pointer dereference upon shrinking
- llc: make llc_ui_sendmsg() more robust against bonding changes
- smc: fix illegal rmb_desc access in SMC-D connection dump
- dpll: fix pin dump crash for rebound module
- bnxt_en: fix possible crash after creating sw mqprio TCs
- hv_netvsc: calculate correct ring size when PAGE_SIZE is not 4kB
Misc:
- several self-tests fixes for better integration with the netdev CI
- added several missing modules descriptions"
* tag 'net-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (88 commits)
tsnep: Fix XDP_RING_NEED_WAKEUP for empty fill ring
tsnep: Remove FCS for XDP data path
net: fec: fix the unhandled context fault from smmu
selftests: bonding: do not test arp/ns target with mode balance-alb/tlb
fjes: fix memleaks in fjes_hw_setup
i40e: update xdp_rxq_info::frag_size for ZC enabled Rx queue
i40e: set xdp_rxq_info::frag_size
xdp: reflect tail increase for MEM_TYPE_XSK_BUFF_POOL
ice: update xdp_rxq_info::frag_size for ZC enabled Rx queue
intel: xsk: initialize skb_frag_t::bv_offset in ZC drivers
ice: remove redundant xdp_rxq_info registration
i40e: handle multi-buffer packets that are shrunk by xdp prog
ice: work on pre-XDP prog frag count
xsk: fix usage of multi-buffer BPF helpers for ZC XDP
xsk: make xsk_buff_pool responsible for clearing xdp_buff::flags
xsk: recycle buffer in case Rx queue was full
net: fill in MODULE_DESCRIPTION()s for rvu_mbox
net: fill in MODULE_DESCRIPTION()s for litex
net: fill in MODULE_DESCRIPTION()s for fsl_pq_mdio
net: fill in MODULE_DESCRIPTION()s for fec
...
Linus Torvalds [Thu, 25 Jan 2024 18:52:30 +0000 (10:52 -0800)]
Merge tag 'ovl-fixes-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs
Pull overlayfs fix from Amir Goldstein:
"Change the on-disk format for the new "xwhiteouts" feature introduced
in v6.7
The change reduces unneeded overhead of an extra getxattr per readdir.
The only user of the "xwhiteout" feature is the external composefs
tool, which has been updated to support the new on-disk format.
This change is also designated for 6.7.y"
* tag 'ovl-fixes-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/overlayfs/vfs:
ovl: mark xwhiteouts directory with overlay.opaque='x'
Linus Torvalds [Thu, 25 Jan 2024 18:41:29 +0000 (10:41 -0800)]
Merge tag 'vfs-6.8-rc2.netfs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull netfs fixes from Christian Brauner:
"This contains various fixes for the netfs work merged earlier this
cycle:
afs:
- Fix locking imbalance in afs_proc_addr_prefs_show()
- Remove afs_dynroot_d_revalidate() which is redundant
- Fix error handling during lookup
- Hide sillyrenames from userspace. This fixes a race between
silly-rename files being created/removed and userspace iterating
over directory entries
- Don't use unnecessary folio_*() functions
cifs:
- Don't use unnecessary folio_*() functions
cachefiles:
- erofs: Fix Null dereference when cachefiles are not doing
ondemand-mode
- Update mailing list
netfs library:
- Add Jeff Layton as reviewer
- Update mailing list
- Fix a error checking in netfs_perform_write()
- fscache: Check error before dereferencing
- Don't use unnecessary folio_*() functions"
* tag 'vfs-6.8-rc2.netfs' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
afs: Fix missing/incorrect unlocking of RCU read lock
afs: Remove afs_dynroot_d_revalidate() as it is redundant
afs: Fix error handling with lookup via FS.InlineBulkStatus
afs: Hide silly-rename files from userspace
cachefiles, erofs: Fix NULL deref in when cachefiles is not doing ondemand-mode
netfs: Fix a NULL vs IS_ERR() check in netfs_perform_write()
netfs, fscache: Prevent Oops in fscache_put_cache()
cifs: Don't use certain unnecessary folio_*() functions
afs: Don't use certain unnecessary folio_*() functions
netfs: Don't use certain unnecessary folio_*() functions
netfs: Add Jeff Layton as reviewer
netfs, cachefiles: Change mailing list
Linus Torvalds [Thu, 25 Jan 2024 18:26:52 +0000 (10:26 -0800)]
Merge tag 'nfsd-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Fix in-kernel RPC UDP transport
- Fix NFSv4.0 RELEASE_LOCKOWNER
* tag 'nfsd-6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: fix RELEASE_LOCKOWNER
SUNRPC: use request size to initialize bio_vec in svc_udp_sendto()
Linus Torvalds [Thu, 25 Jan 2024 18:21:21 +0000 (10:21 -0800)]
Merge tag 'urgent-rcu.2024.01.24a' of https://github.com/neeraju/linux
Pull RCU fix from Neeraj Upadhyay:
"This fixes RCU grace period stalls, which are observed when an
outgoing CPU's quiescent state reporting results in wakeup of one of
the grace period kthreads, to complete the grace period.
If those kthreads have SCHED_FIFO policy, the wake up can indirectly
arm the RT bandwith timer to the local offline CPU.
Earlier migration of the hrtimers from the CPU introduced in commit 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU
earlier") results in this timer getting ignored.
If the RCU grace period kthreads are waiting for RT bandwidth to be
available, they may never be actually scheduled, resulting in RCU
stall warnings"
* tag 'urgent-rcu.2024.01.24a' of https://github.com/neeraju/linux:
rcu: Defer RCU kthreads wakeup when CPU is dying
Baochen Qiang [Tue, 23 Jan 2024 02:57:00 +0000 (10:57 +0800)]
wifi: ath11k: fix connection failure due to unexpected peer delete
Currently ath11k_mac_op_unassign_vif_chanctx() deletes peer but
ath11k_mac_op_assign_vif_chanctx() doesn't create it. This results in
connection failure if MAC80211 calls drv_unassign_vif_chanctx() and
drv_assign_vif_chanctx() during AUTH and ASSOC, see below log:
[ 102.372431] wlan0: authenticated
[ 102.372585] ath11k_pci 0000:01:00.0: wlan0: disabling HT/VHT/HE as WMM/QoS is not supported by the AP
[ 102.372593] ath11k_pci 0000:01:00.0: mac chanctx unassign ptr ffff895084638598 vdev_id 0
[ 102.372808] ath11k_pci 0000:01:00.0: WMI vdev stop id 0x0
[ 102.383114] ath11k_pci 0000:01:00.0: vdev stopped for vdev id 0
[ 102.384689] ath11k_pci 0000:01:00.0: WMI peer delete vdev_id 0 peer_addr 20:e5:2a:21:c4:51
[ 102.396676] ath11k_pci 0000:01:00.0: htt peer unmap vdev 0 peer 20:e5:2a:21:c4:51 id 3
[ 102.396711] ath11k_pci 0000:01:00.0: peer delete resp for vdev id 0 addr 20:e5:2a:21:c4:51
[ 102.396722] ath11k_pci 0000:01:00.0: mac removed peer 20:e5:2a:21:c4:51 vdev 0 after vdev stop
[ 102.396780] ath11k_pci 0000:01:00.0: mac chanctx assign ptr ffff895084639c18 vdev_id 0
[ 102.400628] wlan0: associate with 20:e5:2a:21:c4:51 (try 1/3)
[ 102.508864] wlan0: associate with 20:e5:2a:21:c4:51 (try 2/3)
[ 102.612815] wlan0: associate with 20:e5:2a:21:c4:51 (try 3/3)
[ 102.720846] wlan0: association with 20:e5:2a:21:c4:51 timed out
The peer delete logic in ath11k_mac_op_unassign_vif_chanctx() is
introduced by commit b4a0f54156ac ("ath11k: move peer delete after
vdev stop of station for QCA6390 and WCN6855") to fix firmware
crash issue caused by unexpected vdev stop/peer delete sequence.
Actually for a STA interface peer should be deleted in
ath11k_mac_op_sta_state() when STA's state changes from
IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST, which also coincides
with current peer creation design that peer is created during
IEEE80211_STA_NOTEXIST -> IEEE80211_STA_NONE transition. So move
peer delete back to ath11k_mac_op_sta_state(), also stop vdev before
deleting peer to fix the firmware crash issue mentioned there. In
this way the connection failure mentioned here is also fixed.
Baochen Qiang [Tue, 23 Jan 2024 02:56:59 +0000 (10:56 +0800)]
wifi: ath11k: avoid forward declaration of ath11k_mac_start_vdev_delay()
Currently ath11k_mac_start_vdev_delay() needs a forward declaration because
it is defined after where it is called. Avoid this by re-arranging
ath11k_mac_station_add() and ath11k_mac_op_sta_state().
Baochen Qiang [Tue, 23 Jan 2024 02:56:57 +0000 (10:56 +0800)]
wifi: ath11k: remove invalid peer create logic
In ath11k_mac_op_assign_vif_chanctx(), there is a logic to
create peer using ar->mac_addr for a STA vdev. This is invalid
because a STA vdev should have a peer created using AP's
MAC address. Besides, if we run into that logic, it means a peer
has already been created earlier, we should not create it again.
So remove it.
Baochen Qiang [Tue, 23 Jan 2024 01:52:01 +0000 (09:52 +0800)]
wifi: ath11k: enable 36 bit mask for stream DMA
Currently 32 bit DMA mask is used, telling kernel to get us an DMA
address under 4GB when mapping a buffer. This results in a very high
CPU overhead in the case where IOMMU is disabled and more than 4GB
system memory is installed. The reason is, with more than 4GB memory
installed, kernel is likely to allocate a buffer whose physical
address is above 4GB. While with IOMMU disabled, kernel has to involve
SWIOTLB to map/unmap that buffer, which consumes lots of CPU cycles.
We did hit an issue caused by the reason mentioned above: in a system
that disables IOMMU and gets 8GB memory installed, a total of 40.5%
CPU usage is observed in throughput test. CPU profiling shows nearly
60% of CPU cycles are consumed by SWIOTLB.
By enabling 36 bit DMA mask, we can bypass SWIOTLB for any buffer
whose physical address is below 64GB. There are two types of DMA mask
within struct device, named dma_mask and coherent_dma_mask. Here we
only enable 36 bit for dma_mask, because firmware crashes if
coherent_dma_mask is also enabled, due to some unknown hardware
limitations. This is acceptable because coherent_dma_mask is used for
mapping a consistent DMA buffer, which generally does not happen in
a hot path.
With this change, the total CPU usage mentioned in above issue drops
to 18.9%.
Arınç ÜNAL [Mon, 22 Jan 2024 05:34:31 +0000 (08:34 +0300)]
net: dsa: mt7530: support OF-based registration of switch MDIO bus
Currently the MDIO bus of the switches the MT7530 DSA subdriver controls
can only be registered as non-OF-based. Bring support for registering the
bus OF-based.
The subdrivers that control switches [with MDIO bus] probed on OF must
follow this logic to support all cases properly:
No switch MDIO bus defined: Populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if "interrupt-controller" is defined at
the switch node. This case should only be covered for the switches which
their dt-bindings documentation didn't document the MDIO bus from the
start. This is to keep supporting the device trees that do not describe the
MDIO bus on the device tree but the MDIO bus is being used nonetheless.
Switch MDIO bus defined: Don't populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if ["interrupt-controller" is defined at
the switch node and "interrupts" is defined at the PHY nodes under the
switch MDIO bus node].
Switch MDIO bus defined but explicitly disabled: If the device tree says
status = "disabled" for the MDIO bus, we shouldn't need an MDIO bus at all.
Instead, just exit as early as possible and do not call any MDIO API.
The use of ds->user_mii_bus is inappropriate when the MDIO bus of the
switch is described on the device tree [1], which is why we don't populate
ds->user_mii_bus in that case.
Gerhard Engleder [Tue, 23 Jan 2024 20:09:18 +0000 (21:09 +0100)]
tsnep: Fix XDP_RING_NEED_WAKEUP for empty fill ring
The fill ring of the XDP socket may contain not enough buffers to
completey fill the RX queue during socket creation. In this case the
flag XDP_RING_NEED_WAKEUP is not set as this flag is only set if the RX
queue is not completely filled during polling.
Set XDP_RING_NEED_WAKEUP flag also if RX queue is not completely filled
during XDP socket creation.
Fixes: 3fc2333933fd ("tsnep: Add XDP socket zero-copy RX support") Signed-off-by: Gerhard Engleder <[email protected]> Signed-off-by: Paolo Abeni <[email protected]>
Gerhard Engleder [Tue, 23 Jan 2024 20:09:17 +0000 (21:09 +0100)]
tsnep: Remove FCS for XDP data path
The RX data buffer includes the FCS. The FCS is already stripped for the
normal data path. But for the XDP data path the FCS is included and
acts like additional/useless data.
Remove the FCS from the RX data buffer also for XDP.
Paolo Abeni [Thu, 25 Jan 2024 10:42:27 +0000 (11:42 +0100)]
Merge tag 'mlx5-fixes-2024-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2024-01-24
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2024-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: fix a potential double-free in fs_any_create_groups
net/mlx5e: fix a double-free in arfs_create_groups
net/mlx5e: Ignore IPsec replay window values on sender side
net/mlx5e: Allow software parsing when IPsec crypto is enabled
net/mlx5: Use mlx5 device constant for selecting CQ period mode for ASO
net/mlx5: DR, Can't go to uplink vport on RX rule
net/mlx5: DR, Use the right GVMI number for drop action
net/mlx5: Bridge, fix multicast packets sent to uplink
net/mlx5: Fix a WARN upon a callback command failure
net/mlx5e: Fix peer flow lists handling
net/mlx5e: Fix inconsistent hairpin RQT sizes
net/mlx5e: Fix operation precedence bug in port timestamping napi_poll context
net/mlx5: Fix query of sd_group field
net/mlx5e: Use the correct lag ports number when creating TISes
====================
Paolo Abeni [Thu, 25 Jan 2024 10:30:31 +0000 (11:30 +0100)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2024-01-25
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 2 day(s) which contain
a total of 13 files changed, 190 insertions(+), 91 deletions(-).
The main changes are:
1) Fix bpf_xdp_adjust_tail() in context of XSK zero-copy drivers which
support XDP multi-buffer. The former triggered a NULL pointer
dereference upon shrinking, from Maciej Fijalkowski & Tirthendu Sarkar.
2) Fix a bug in riscv64 BPF JIT which emitted a wrong prologue and
epilogue for struct_ops programs, from Pu Lehui.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
i40e: update xdp_rxq_info::frag_size for ZC enabled Rx queue
i40e: set xdp_rxq_info::frag_size
xdp: reflect tail increase for MEM_TYPE_XSK_BUFF_POOL
ice: update xdp_rxq_info::frag_size for ZC enabled Rx queue
intel: xsk: initialize skb_frag_t::bv_offset in ZC drivers
ice: remove redundant xdp_rxq_info registration
i40e: handle multi-buffer packets that are shrunk by xdp prog
ice: work on pre-XDP prog frag count
xsk: fix usage of multi-buffer BPF helpers for ZC XDP
xsk: make xsk_buff_pool responsible for clearing xdp_buff::flags
xsk: recycle buffer in case Rx queue was full
riscv, bpf: Fix unpredictable kernel crash about RV64 struct_ops
====================
Shenwei Wang [Tue, 23 Jan 2024 16:51:41 +0000 (10:51 -0600)]
net: fec: fix the unhandled context fault from smmu
When repeatedly changing the interface link speed using the command below:
ethtool -s eth0 speed 100 duplex full
ethtool -s eth0 speed 1000 duplex full
The following errors may sometimes be reported by the ARM SMMU driver:
[ 5395.035364] fec 5b040000.ethernet eth0: Link is Down
[ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault:
fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2
[ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
It is identified that the FEC driver does not properly stop the TX queue
during the link speed transitions, and this results in the invalid virtual
I/O address translations from the SMMU and causes the context faults.
Hangbin Liu [Tue, 23 Jan 2024 07:59:17 +0000 (15:59 +0800)]
selftests: bonding: do not test arp/ns target with mode balance-alb/tlb
The prio_arp/ns tests hard code the mode to active-backup. At the same
time, The balance-alb/tlb modes do not support arp/ns target. So remove
the prio_arp/ns tests from the loop and only test active-backup mode.
Jakub Kicinski [Thu, 25 Jan 2024 05:03:16 +0000 (21:03 -0800)]
Merge tag 'nf-24-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Update nf_tables kdoc to keep it in sync with the code, from George Guo.
2) Handle NETDEV_UNREGISTER event for inet/ingress basechain.
3) Reject configuration that cause nft_limit to overflow,
from Florian Westphal.
4) Restrict anonymous set/map names to 16 bytes, from Florian Westphal.
5) Disallow to encode queue number and error in verdicts. This reverts
a patch which seems to have introduced an early attempt to support for
nfqueue maps, which is these days supported via nft_queue expression.
6) Sanitize family via .validate for expressions that explicitly refer
to NF_INET_* hooks.
* tag 'nf-24-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: validate NFPROTO_* family
netfilter: nf_tables: reject QUEUE/DROP verdict parameters
netfilter: nf_tables: restrict anonymous set and map names to 16 bytes
netfilter: nft_limit: reject configurations that cause integer overflow
netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress basechain
netfilter: nf_tables: cleanup documentation
====================
However, when fjes_hw_setup fails, fjes_hw_exit won't be called and thus
all the resources allocated in fjes_hw_setup will be leaked. In this
patch, we free those resources in fjes_hw_setup and prevents such leaks.
Randy Dunlap [Tue, 23 Jan 2024 05:11:52 +0000 (21:11 -0800)]
tipc: node: remove Excess struct member kernel-doc warnings
Remove 2 kernel-doc descriptions to squelch warnings:
node.c:150: warning: Excess struct member 'inputq' description in 'tipc_node'
node.c:150: warning: Excess struct member 'namedq' description in 'tipc_node'
Arseniy Krasnov [Tue, 23 Jan 2024 07:27:50 +0000 (10:27 +0300)]
vsock/test: add '--peer-port' input argument
Implement port for given CID as input argument instead of using
hardcoded value '1234'. This allows to run different test instances
on a single CID. Port argument is not required parameter and if it is
not set, then default value will be '1234' - thus we preserve previous
behaviour.
Linus Torvalds [Thu, 25 Jan 2024 00:59:52 +0000 (16:59 -0800)]
Merge tag 'ceph-for-6.8-rc2' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix to avoid triggering an assert in some cases where RBD exclusive
mappings are involved and a deprecated API cleanup"
* tag 'ceph-for-6.8-rc2' of https://github.com/ceph/ceph-client:
rbd: don't move requests to the running list on errors
rbd: remove usage of the deprecated ida_simple_*() API
Linus Torvalds [Thu, 25 Jan 2024 00:51:59 +0000 (16:51 -0800)]
Merge tag 'integrity-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity fix from Mimi Zohar:
"Revert patch that required user-provided key data, since keys can be
created from kernel-generated random numbers"
* tag 'integrity-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
Revert "KEYS: encrypted: Add check for strsep"
====================
net: bpf_xdp_adjust_tail() and Intel mbuf fixes
Hey,
after a break followed by dealing with sickness, here is a v6 that makes
bpf_xdp_adjust_tail() actually usable for ZC drivers that support XDP
multi-buffer. Since v4 I tried also using bpf_xdp_adjust_tail() with
positive offset which exposed yet another issues, which can be observed
by increased commit count when compared to v3.
John, in the end I think we should remove handling
MEM_TYPE_XSK_BUFF_POOL from __xdp_return(), but it is out of the scope
for fixes set, IMHO.
v5:
- pick correct version of patch 5 [Simon]
- elaborate a bit more on what patch 2 fixes
v4:
- do not clear frags flag when deleting tail; xsk_buff_pool now does
that
- skip some NULL tests for xsk_buff_get_tail [Martin, John]
- address problems around registering xdp_rxq_info
- fix bpf_xdp_frags_increase_tail() for ZC mbuf
v3:
- add acks
- s/xsk_buff_tail_del/xsk_buff_del_tail
- address i40e as well (thanks Tirthendu)
v2:
- fix !CONFIG_XDP_SOCKETS builds
- add reviewed-by tag to patch 3
====================
i40e: update xdp_rxq_info::frag_size for ZC enabled Rx queue
Now that i40e driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. i40e_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
i40e support XDP multi-buffer so it is supposed to use
__xdp_rxq_info_reg() instead of xdp_rxq_info_reg() and set the
frag_size. It can not be simply converted at existing callsite because
rx_buf_len could be un-initialized, so let us register xdp_rxq_info
within i40e_configure_rx_ring(), which happen to be called with already
initialized rx_buf_len value.
Commit 5180ff1364bc ("i40e: use int for i40e_status") converted 'err' to
int, so two variables to deal with return codes are not needed within
i40e_configure_rx_ring(). Remove 'ret' and use 'err' to handle status
from xdp_rxq_info registration.
xdp: reflect tail increase for MEM_TYPE_XSK_BUFF_POOL
XSK ZC Rx path calculates the size of data that will be posted to XSK Rx
queue via subtracting xdp_buff::data_end from xdp_buff::data.
In bpf_xdp_frags_increase_tail(), when underlying memory type of
xdp_rxq_info is MEM_TYPE_XSK_BUFF_POOL, add offset to data_end in tail
fragment, so that later on user space will be able to take into account
the amount of bytes added by XDP program.
ice: update xdp_rxq_info::frag_size for ZC enabled Rx queue
Now that ice driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. ice_rx_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Use a bigger hammer and instead of unregistering only xdp_rxq_info's
memory model, unregister it altogether and register it again and have
xdp_rxq_info with correct frag_size value.
intel: xsk: initialize skb_frag_t::bv_offset in ZC drivers
Ice and i40e ZC drivers currently set offset of a frag within
skb_shared_info to 0, which is incorrect. xdp_buffs that come from
xsk_buff_pool always have 256 bytes of a headroom, so they need to be
taken into account to retrieve xdp_buff::data via skb_frag_address().
Otherwise, bpf_xdp_frags_increase_tail() would be starting its job from
xdp_buff::data_hard_start which would result in overwriting existing
payload.
xdp_rxq_info struct can be registered by drivers via two functions -
xdp_rxq_info_reg() and __xdp_rxq_info_reg(). The latter one allows
drivers that support XDP multi-buffer to set up xdp_rxq_info::frag_size
which in turn will make it possible to grow the packet via
bpf_xdp_adjust_tail() BPF helper.
Currently, ice registers xdp_rxq_info in two spots:
1) ice_setup_rx_ring() // via xdp_rxq_info_reg(), BUG
2) ice_vsi_cfg_rxq() // via __xdp_rxq_info_reg(), OK
Cited commit under fixes tag took care of setting up frag_size and
updated registration scheme in 2) but it did not help as
1) is called before 2) and as shown above it uses old registration
function. This means that 2) sees that xdp_rxq_info is already
registered and never calls __xdp_rxq_info_reg() which leaves us with
xdp_rxq_info::frag_size being set to 0.
To fix this misbehavior, simply remove xdp_rxq_info_reg() call from
ice_setup_rx_ring().
Tirthendu Sarkar [Wed, 24 Jan 2024 19:15:56 +0000 (20:15 +0100)]
i40e: handle multi-buffer packets that are shrunk by xdp prog
XDP programs can shrink packets by calling the bpf_xdp_adjust_tail()
helper function. For multi-buffer packets this may lead to reduction of
frag count stored in skb_shared_info area of the xdp_buff struct. This
results in issues with the current handling of XDP_PASS and XDP_DROP
cases.
For XDP_PASS, currently skb is being built using frag count of
xdp_buffer before it was processed by XDP prog and thus will result in
an inconsistent skb when frag count gets reduced by XDP prog. To fix
this, get correct frag count while building the skb instead of using
pre-obtained frag count.
For XDP_DROP, current page recycling logic will not reuse the page but
instead will adjust the pagecnt_bias so that the page can be freed. This
again results in inconsistent behavior as the page refcnt has already
been changed by the helper while freeing the frag(s) as part of
shrinking the packet. To fix this, only adjust pagecnt_bias for buffers
that are stillpart of the packet post-xdp prog run.
Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.
Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.
To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.
While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.
This comes from __xdp_return() call with xdp_buff argument passed as
NULL which is supposed to be consumed by xsk_buff_free() call.
To address this properly, in ZC case, a node that represents the frag
being removed has to be pulled out of xskb_list. Introduce
appropriate xsk helpers to do such node operation and use them
accordingly within bpf_xdp_adjust_tail().
xsk: make xsk_buff_pool responsible for clearing xdp_buff::flags
XDP multi-buffer support introduced XDP_FLAGS_HAS_FRAGS flag that is
used by drivers to notify data path whether xdp_buff contains fragments
or not. Data path looks up mentioned flag on first buffer that occupies
the linear part of xdp_buff, so drivers only modify it there. This is
sufficient for SKB and XDP_DRV modes as usually xdp_buff is allocated on
stack or it resides within struct representing driver's queue and
fragments are carried via skb_frag_t structs. IOW, we are dealing with
only one xdp_buff.
ZC mode though relies on list of xdp_buff structs that is carried via
xsk_buff_pool::xskb_list, so ZC data path has to make sure that
fragments do *not* have XDP_FLAGS_HAS_FRAGS set. Otherwise,
xsk_buff_free() could misbehave if it would be executed against xdp_buff
that carries a frag with XDP_FLAGS_HAS_FRAGS flag set. Such scenario can
take place when within supplied XDP program bpf_xdp_adjust_tail() is
used with negative offset that would in turn release the tail fragment
from multi-buffer frame.
Calling xsk_buff_free() on tail fragment with XDP_FLAGS_HAS_FRAGS would
result in releasing all the nodes from xskb_list that were produced by
driver before XDP program execution, which is not what is intended -
only tail fragment should be deleted from xskb_list and then it should
be put onto xsk_buff_pool::free_list. Such multi-buffer frame will never
make it up to user space, so from AF_XDP application POV there would be
no traffic running, however due to free_list getting constantly new
nodes, driver will be able to feed HW Rx queue with recycled buffers.
Bottom line is that instead of traffic being redirected to user space,
it would be continuously dropped.
To fix this, let us clear the mentioned flag on xsk_buff_pool side
during xdp_buff initialization, which is what should have been done
right from the start of XSK multi-buffer support.
Jakub Kicinski [Wed, 24 Jan 2024 23:12:55 +0000 (15:12 -0800)]
Merge branch 'fix-module_description-for-net-p2'
Breno Leitao says:
====================
Fix MODULE_DESCRIPTION() for net (p2)
There are hundreds of network modules that misses MODULE_DESCRIPTION(),
causing a warnning when compiling with W=1. Example:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/com90io.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/arc-rimi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/com20020.o
This part2 of the patchset focus on the drivers/net/ethernet drivers.
There are still some missing warnings in drivers/net/ethernet that will
be fixed in an upcoming patchset.
Jakub Kicinski [Tue, 23 Jan 2024 06:05:29 +0000 (22:05 -0800)]
selftests: netdevsim: fix the udp_tunnel_nic test
This test is missing a whole bunch of checks for interface
renaming and one ifup. Presumably it was only used on a system
with renaming disabled and NetworkManager running.
Jakub Kicinski [Mon, 22 Jan 2024 19:58:15 +0000 (11:58 -0800)]
selftests: net: fix rps_default_mask with >32 CPUs
If there is more than 32 cpus the bitmask will start to contain
commas, leading to:
./rps_default_mask.sh: line 36: [: 00000000,00000000: integer expression expected
Remove the commas, bash doesn't interpret leading zeroes as oct
so that should be good enough. Switch to bash, Simon reports that
not all shells support this type of substitution.
Linus Torvalds [Wed, 24 Jan 2024 21:12:20 +0000 (13:12 -0800)]
uselib: remove use of __FMODE_EXEC
Jann Horn points out that uselib() really shouldn't trigger the new
FMODE_EXEC logic introduced by commit 4759ff71f23e ("exec: __FMODE_EXEC
instead of in_execve for LSMs").
In fact, it shouldn't even have ever triggered the old pre-existing
logic for __FMODE_EXEC (like the NFS code that makes executables not
need read permissions). Unlike a real execve(), that can work even with
files that are purely executable by the user (not readable), uselib()
has that MAY_READ requirement becasue it's really just a convenience
wrapper around mmap() for legacy shared libraries.
The whole FMODE_EXEC bit was originally introduced by commit b500531e6f5f ("[PATCH] Introduce FMODE_EXEC file flag"), primarily to
give ETXTBUSY error returns for distributed filesystems.
It has since grown a few other warts (like that NFS thing), but there
really isn't any reason to use it for uselib(), and now that we are
trying to use it to replace the horrid 'tsk->in_execve' flag, it's
actively wrong.
Of course, as Jann Horn also points out, nobody should be enabling
CONFIG_USELIB in the first place in this day and age, but that's a
different discussion entirely.
New encrypted keys are created either from kernel-generated random
numbers or user-provided decrypted data. Revert the change requiring
user-provided decrypted data.
Register value persist after booting the kernel using
kexec which results in kernel panic. Thus clear the
BM pool registers before initialisation to fix the issue.
Bernd Edlinger [Mon, 22 Jan 2024 18:19:09 +0000 (19:19 +0100)]
net: stmmac: Wait a bit for the reset to take effect
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
Kees Cook [Wed, 24 Jan 2024 19:15:33 +0000 (11:15 -0800)]
exec: Distinguish in_execve from in_exec
Just to help distinguish the fs->in_exec flag from the current->in_execve
flag, add comments in check_unsafe_exec() and copy_fs() for more
context. Also note that in_execve is only used by TOMOYO now.
Kees Cook [Wed, 24 Jan 2024 19:22:32 +0000 (11:22 -0800)]
exec: Check __FMODE_EXEC instead of in_execve for LSMs
After commit 978ffcbf00d8 ("execve: open the executable file before
doing anything else"), current->in_execve was no longer in sync with the
open(). This broke AppArmor and TOMOYO which depend on this flag to
distinguish "open" operations from being "exec" operations.
Instead of moving around in_execve, switch to using __FMODE_EXEC, which
is where the "is this an exec?" intent is stored. Note that TOMOYO still
uses in_execve around cred handling.
core.c:nf_hook_slow assumes that the upper 16 bits of NF_DROP
verdicts contain a valid errno, i.e. -EPERM, -EHOSTUNREACH or similar,
or 0.
Due to the reverted commit, its possible to provide a positive
value, e.g. NF_ACCEPT (1), which results in use-after-free.
Its not clear to me why this commit was made.
NF_QUEUE is not used by nftables; "queue" rules in nftables
will result in use of "nft_queue" expression.
If we later need to allow specifiying errno values from userspace
(do not know why), this has to call NF_DROP_GETERR and check that
"err <= 0" holds true.
Florian Westphal [Fri, 19 Jan 2024 12:34:32 +0000 (13:34 +0100)]
netfilter: nf_tables: restrict anonymous set and map names to 16 bytes
nftables has two types of sets/maps, one where userspace defines the
name, and anonymous sets/maps, where userspace defines a template name.
For the latter, kernel requires presence of exactly one "%d".
nftables uses "__set%d" and "__map%d" for this. The kernel will
expand the format specifier and replaces it with the smallest unused
number.
As-is, userspace could define a template name that allows to move
the set name past the 256 bytes upperlimit (post-expansion).
I don't see how this could be a problem, but I would prefer if userspace
cannot do this, so add a limit of 16 bytes for the '%d' template name.
16 bytes is the old total upper limit for set names that existed when
nf_tables was merged initially.
Fixes: 387454901bd6 ("netfilter: nf_tables: Allow set names of up to 255 chars") Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: Pablo Neira Ayuso <[email protected]>
netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress basechain
Remove netdevice from inet/ingress basechain in case NETDEV_UNREGISTER
event is reported, otherwise a stale reference to netdevice remains in
the hook list.
When the CPU goes idle for the last time during the CPU down hotplug
process, RCU reports a final quiescent state for the current CPU. If
this quiescent state propagates up to the top, some tasks may then be
woken up to complete the grace period: the main grace period kthread
and/or the expedited main workqueue (or kworker).
If those kthreads have a SCHED_FIFO policy, the wake up can indirectly
arm the RT bandwith timer to the local offline CPU. Since this happens
after hrtimers have been migrated at CPUHP_AP_HRTIMERS_DYING stage, the
timer gets ignored. Therefore if the RCU kthreads are waiting for RT
bandwidth to be available, they may never be actually scheduled.
The situation can't be solved with just unpinning the timer. The hrtimer
infrastructure and the nohz heuristics involved in finding the best
remote target for an unpinned timer would then also need to handle
enqueues from an offline CPU in the most horrendous way.
So fix this on the RCU side instead and defer the wake up to an online
CPU if it's too late for the local one.
Reported-by: Paul E. McKenney <[email protected]> Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier") Signed-off-by: Frederic Weisbecker <[email protected]> Signed-off-by: Paul E. McKenney <[email protected]> Signed-off-by: Neeraj Upadhyay (AMD) <[email protected]>
Linus Torvalds [Wed, 24 Jan 2024 16:55:51 +0000 (08:55 -0800)]
Merge tag 'fbdev-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes and cleanups from Helge Deller:
"A crash fix in stifb which was missed to be included in the drm-misc
tree, two checks to prevent wrong userspace input in sisfb and
savagefb and two trivial printk cleanups:
- stifb: Fix crash in stifb_blank()
- savage/sis: Error out if pixclock equals zero
- minor trivial cleanups"
* tag 'fbdev-for-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: stifb: Fix crash in stifb_blank()
fbcon: Fix incorrect printed function name in fbcon_prepare_logo()
fbdev: sis: Error out if pixclock equals zero
fbdev: savage: Error out if pixclock equals zero
fbdev: vt8500lcdfb: Remove unnecessary print function dev_err()
NeilBrown [Mon, 22 Jan 2024 03:58:16 +0000 (14:58 +1100)]
nfsd: fix RELEASE_LOCKOWNER
The test on so_count in nfsd4_release_lockowner() is nonsense and
harmful. Revert to using check_for_locks(), changing that to not sleep.
First: harmful.
As is documented in the kdoc comment for nfsd4_release_lockowner(), the
test on so_count can transiently return a false positive resulting in a
return of NFS4ERR_LOCKS_HELD when in fact no locks are held. This is
clearly a protocol violation and with the Linux NFS client it can cause
incorrect behaviour.
If RELEASE_LOCKOWNER is sent while some other thread is still
processing a LOCK request which failed because, at the time that request
was received, the given owner held a conflicting lock, then the nfsd
thread processing that LOCK request can hold a reference (conflock) to
the lock owner that causes nfsd4_release_lockowner() to return an
incorrect error.
The Linux NFS client ignores that NFS4ERR_LOCKS_HELD error because it
never sends NFS4_RELEASE_LOCKOWNER without first releasing any locks, so
it knows that the error is impossible. It assumes the lock owner was in
fact released so it feels free to use the same lock owner identifier in
some later locking request.
When it does reuse a lock owner identifier for which a previous RELEASE
failed, it will naturally use a lock_seqid of zero. However the server,
which didn't release the lock owner, will expect a larger lock_seqid and
so will respond with NFS4ERR_BAD_SEQID.
So clearly it is harmful to allow a false positive, which testing
so_count allows.
The test is nonsense because ... well... it doesn't mean anything.
so_count is the sum of three different counts.
1/ the set of states listed on so_stateids
2/ the set of active vfs locks owned by any of those states
3/ various transient counts such as for conflicting locks.
When it is tested against '2' it is clear that one of these is the
transient reference obtained by find_lockowner_str_locked(). It is not
clear what the other one is expected to be.
In practice, the count is often 2 because there is precisely one state
on so_stateids. If there were more, this would fail.
In my testing I see two circumstances when RELEASE_LOCKOWNER is called.
In one case, CLOSE is called before RELEASE_LOCKOWNER. That results in
all the lock states being removed, and so the lockowner being discarded
(it is removed when there are no more references which usually happens
when the lock state is discarded). When nfsd4_release_lockowner() finds
that the lock owner doesn't exist, it returns success.
The other case shows an so_count of '2' and precisely one state listed
in so_stateid. It appears that the Linux client uses a separate lock
owner for each file resulting in one lock state per lock owner, so this
test on '2' is safe. For another client it might not be safe.
So this patch changes check_for_locks() to use the (newish)
find_any_file_locked() so that it doesn't take a reference on the
nfs4_file and so never calls nfsd_file_put(), and so never sleeps. With
this check is it safe to restore the use of check_for_locks() rather
than testing so_count against the mysterious '2'.
Sriram R [Wed, 17 Jan 2024 06:26:28 +0000 (11:56 +0530)]
wifi: ath12k: Fix issues in channel list update
Currently, the logic used to select the 6 GHz band is incorrect,
which may cause 6 GHz supported channels to not be updated properly.
This is because the 6 GHz Max frequency supported by the driver is
being compared to the Max frequency supported on the board. If in
some cases, the 6 GHz Max frequency supported on the board is less
than the defined 6 GHz Max frequency, all 6 GHz channels are disabled.
To address this, compare the max frequency supported by the board to
the defined 6 GHz Minimum frequency by the driver.
Similarly, when a dual mac card supports both 6 GHz and 5 GHz radios,
if the 5 GHz radio gets enumerated first before 6 GHz, the checks in
ath12k_mac_setup_channels_rates() can cause the 5 GHz channels which
were enabled earlier to get disabled when the 6 GHz channel list is
updated. This is because the Min 6 GHz frequency defined in the driver
is 5945 MHz, which should be 5925 MHz since channel 2 is not considered
currently, but the firmware can pass 5925 MHz as the minimum.
Hence, update the Min frequency supported by the driver to 5925 MHz.
In addition, ensure that the channel list update to firmware updates
only the channels that the current radio (ar) supports rather than
considering the wiphy support. This would be required when multiple pdevs
are supported in a wiphy and they support different ranges of frequencies
or bands as in single wiphy support.
Dinghao Liu [Tue, 28 Nov 2023 09:29:01 +0000 (17:29 +0800)]
net/mlx5e: fix a potential double-free in fs_any_create_groups
When kcalloc() for ft->g succeeds but kvzalloc() for in fails,
fs_any_create_groups() will free ft->g. However, its caller
fs_any_create_table() will free ft->g again through calling
mlx5e_destroy_flow_table(), which will lead to a double-free.
Fix this by setting ft->g to NULL in fs_any_create_groups().
Zhipeng Lu [Wed, 17 Jan 2024 07:17:36 +0000 (15:17 +0800)]
net/mlx5e: fix a double-free in arfs_create_groups
When `in` allocated by kvzalloc fails, arfs_create_groups will free
ft->g and return an error. However, arfs_create_table, the only caller of
arfs_create_groups, will hold this error and call to
mlx5e_destroy_flow_table, in which the ft->g will be freed again.
Leon Romanovsky [Sun, 26 Nov 2023 09:08:10 +0000 (11:08 +0200)]
net/mlx5e: Ignore IPsec replay window values on sender side
XFRM stack doesn't prevent from users to configure replay window
in TX side and strongswan sets replay_window to be 1. It causes
to failures in validation logic when trying to offload the SA.
Replay window is not relevant in TX side and should be ignored.
Fixes: cded6d80129b ("net/mlx5e: Store replay window in XFRM attributes") Signed-off-by: Aya Levin <[email protected]> Signed-off-by: Leon Romanovsky <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Leon Romanovsky [Tue, 12 Dec 2023 11:52:55 +0000 (13:52 +0200)]
net/mlx5e: Allow software parsing when IPsec crypto is enabled
All ConnectX devices have software parsing capability enabled, but it is
more correct to set allow_swp only if capability exists, which for IPsec
means that crypto offload is supported.
Rahul Rameshbabu [Tue, 28 Nov 2023 22:01:54 +0000 (14:01 -0800)]
net/mlx5: Use mlx5 device constant for selecting CQ period mode for ASO
mlx5 devices have specific constants for choosing the CQ period mode. These
constants do not have to match the constants used by the kernel software
API for DIM period mode selection.
Fixes: cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO") Signed-off-by: Rahul Rameshbabu <[email protected]> Reviewed-by: Jianbo Liu <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
net/mlx5: DR, Use the right GVMI number for drop action
When FW provides ICM addresses for drop RX/TX, the provided capability
is 64 bits that contain its GVMI as well as the ICM address itself.
In case of TX DROP this GVMI is different from the GVMI that the
domain is operating on.
This patch fixes the action to use these GVMI IDs, as provided by FW.
Moshe Shemesh [Sat, 30 Dec 2023 20:40:37 +0000 (22:40 +0200)]
net/mlx5: Bridge, fix multicast packets sent to uplink
To enable multicast packets which are offloaded in bridge multicast
offload mode to be sent also to uplink, FTE bit uplink_hairpin_en should
be set. Add this bit to FTE for the bridge multicast offload rules.
Vlad Buslov [Fri, 10 Nov 2023 10:10:22 +0000 (11:10 +0100)]
net/mlx5e: Fix peer flow lists handling
The cited change refactored mlx5e_tc_del_fdb_peer_flow() to only clear DUP
flag when list of peer flows has become empty. However, if any concurrent
user holds a reference to a peer flow (for example, the neighbor update
workqueue task is updating peer flow's parent encap entry concurrently),
then the flow will not be removed from the peer list and, consecutively,
DUP flag will remain set. Since mlx5e_tc_del_fdb_peers_flow() calls
mlx5e_tc_del_fdb_peer_flow() for every possible peer index the algorithm
will try to remove the flow from eswitch instances that it has never peered
with causing either NULL pointer dereference when trying to remove the flow
peer list head of peer_index that was never initialized or a warning if the
list debug config is enabled[0].
Fix the issue by always removing the peer flow from the list even when not
releasing the last reference to it.
Tariq Toukan [Sun, 5 Nov 2023 15:09:46 +0000 (17:09 +0200)]
net/mlx5e: Fix inconsistent hairpin RQT sizes
The processing of traffic in hairpin queues occurs in HW/FW and does not
involve the cpus, hence the upper bound on max num channels does not
apply to them. Using this bound for the hairpin RQT max_table_size is
wrong. It could be too small, and cause the error below [1]. As the
RQT size provided on init does not get modified later, use the same
value for both actual and max table sizes.
[1]
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:805:(pid 1200): CREATE_RQT(0x916) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x538faf), err(-22)
Fixes: 74a8dadac17e ("net/mlx5e: Preparations for supporting larger number of channels") Signed-off-by: Tariq Toukan <[email protected]> Reviewed-by: Gal Pressman <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Rahul Rameshbabu [Thu, 23 Nov 2023 02:32:11 +0000 (18:32 -0800)]
net/mlx5e: Fix operation precedence bug in port timestamping napi_poll context
Indirection (*) is of lower precedence than postfix increment (++). Logic
in napi_poll context would cause an out-of-bound read by first increment
the pointer address by byte address space and then dereference the value.
Rather, the intended logic was to dereference first and then increment the
underlying value.
Fixes: 92214be5979c ("net/mlx5e: Update doorbell for port timestamping CQ before the software counter") Signed-off-by: Rahul Rameshbabu <[email protected]> Reviewed-by: Tariq Toukan <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>
Saeed Mahameed [Sat, 16 Dec 2023 03:31:14 +0000 (19:31 -0800)]
net/mlx5e: Use the correct lag ports number when creating TISes
The cited commit moved the code of mlx5e_create_tises() and changed the
loop to create TISes over MLX5_MAX_PORTS constant value, instead of
getting the correct lag ports supported by the device, which can cause
FW errors on devices with less than MLX5_MAX_PORTS ports.
Change that back to mlx5e_get_num_lag_ports(mdev).
Also IPoIB interfaces create there own TISes, they don't use the eth
TISes, pass a flag to indicate that.
This fixes the following errors that might appear in kernel log:
mlx5_cmd_out_err:808:(pid 650): CREATE_TIS(0x912) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x595b5d), err(-22)
mlx5e_create_mdev_resources:174:(pid 650): alloc tises failed, -22
Fixes: b25bd37c859f ("net/mlx5: Move TISes from priv to mdev HW resources") Signed-off-by: Saeed Mahameed <[email protected]>
====================
gve: Alloc before freeing when changing config
Functions allocating resources did so directly into priv thus far. The
assumption doing that was that priv was not already holding references
to live resources.
When ring configuration is changed in any way from userspace, thus far
we relied on calling the ndo_stop and ndo_open callbacks in succession.
This meant that we teardown existing resources and rob the OS of
networking before we have successfully allocated resources for the new
config.
Correcting this requires us to perform allocations without editing priv.
That is what the "gve: Switch to config-aware..." patch does: it modifies
all the allocation paths so that they take a new configuration as input
and return references to newly allocated resources without modifying
priv or interfering with live resources in any way.
Having corrected the allocation paths so, the ndo open and close
callbacks are refactored to make available distinct functions for
allocating queue resources and starting or stopping them. This is then
put to use in the set_channels and set_features hooks in the last two
patches.
These changes have been tested by verifying the integrity of a stream of
integers while the driver is continuously reconfigured with ethtool.
====================
Shailend Chand [Mon, 22 Jan 2024 18:26:32 +0000 (18:26 +0000)]
gve: Alloc before freeing when changing features
Previously, existing queues were being freed before the resources for
the new queues were being allocated. This would take down the interface
if someone were to attempt to change feature flags under a resource
crunch.
Shailend Chand [Mon, 22 Jan 2024 18:26:31 +0000 (18:26 +0000)]
gve: Alloc before freeing when adjusting queues
Previously, existing queues were being freed before the resources for
the new queues were being allocated. This would take down the interface
if someone were to attempt to change queue counts under a resource
crunch.
Shailend Chand [Mon, 22 Jan 2024 18:26:30 +0000 (18:26 +0000)]
gve: Refactor gve_open and gve_close
gve_open is rewritten to be composed of two funcs: gve_queues_mem_alloc
and gve_queues_start. The former only allocates queue resources without
doing anything to install the queues, which is taken up by the latter.
Similarly gve_close is split into gve_queues_stop and
gve_queues_mem_free.
Separating the acts of queue resource allocation and making the queue
become live help with subsequent changes that aim to not take down the
datapath when applying new configurations.
Shailend Chand [Mon, 22 Jan 2024 18:26:29 +0000 (18:26 +0000)]
gve: Switch to config-aware queue allocation
The new config-aware functions will help achieve the goal of being able
to allocate resources for new queues while there already are active
queues serving traffic.
These new functions work off of arbitrary queue allocation configs
rather than just the currently active config in priv, and they return
the newly allocated resources instead of writing them into priv.
projects / linux.git / log