The intermediate DPMS standby and suspend states are a thing from the
past. They only matter in practice for VGA CRT monitors, and are just a
power saving vs. resume time optimization. Given that they have never
been implemented properly in the rcar-du driver and that the Intel
driver has dropped them on the vga port years ago, it's safe to only
care about the on and off states.
The DU outputs by default a composite sync signal (XOR of the horizontal
and vertical sync signals) on the HSYNC output pin. As this can confuse
devices and isn't needed by any of the supported encoders, configure the
HSYNC pin to output the horizontal sync signal.
drm: rcar-du: Add support for external pixel clock
The DU uses the module functional clock as the default pixel clock, but
supports using an externally supplied pixel clock instead. Support this
by adding the external pixel clock to the DT bindings, and selecting the
clock automatically at runtime based on the requested mode pixel
frequency.
The input clock pins to DU channels routing is configurable, but
currently hardcoded to connect input clock i to channel i.
Rename the feature from RCAR_DU_FEATURE_DEFR8 to
RCAR_DU_FEATURE_EXT_CTRL_REGS to cover all extended control registers in
addition to the DEFR8 register.
Usage of the feature is refactored to optimize runtime operation and
prepare for external clock support.
drm: rcar-du: Configure pitch for chroma plane of multiplanar formats
The PnMWR register containing the plane stride must be programmed with
correct stride values for both the luma and chroma planes when using a
multiplanar format. Fix it.
Laurent Pinchart [Wed, 10 Dec 2014 23:26:04 +0000 (01:26 +0200)]
drm: rcar-du: Don't fail probe in case of partial encoder init error
If an encoder fails to initialize the device can still be used without
the failed encoder. Don't propagate the error out of the probe function
but just skip the failed encoder.
As a special case a deferred probe request from the encoder is still
propagated out of the probe function in order not to break the deferred
probing mechanism.
Linus Torvalds [Mon, 22 Dec 2014 22:47:17 +0000 (14:47 -0800)]
Merge tag 'dm-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Thre stable fixes and one fix for a regression introduced during 3.19
merge:
- Fix inability to discard used space when the thin-pool target is in
out-of-data-space mode and also transition the thin-pool back to
write mode once free space is made available.
- Fix DM core bio-based end_io bug that prevented proper
post-processing of the error code returned from the block layer.
- Fix crash in DM thin-pool due to thin device being added to the
pool's active_thins list before properly initializing the thin
device's refcount"
* tag 'dm-3.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix missed error code if .end_io isn't implemented by target_type
dm thin: fix crash by initializing thin device's refcount and completion earlier
dm thin: fix missing out-of-data-space to write mode transition if blocks are released
dm thin: fix inability to discard blocks when in out-of-data-space mode
Dave Airlie [Mon, 22 Dec 2014 22:24:26 +0000 (08:24 +1000)]
Merge tag 'drm/tegra/for-3.19-rc1-fixes' of git://people.freedesktop.org/~tagr/linux into drm-fixes
drm/tegra: Fixes for v3.19-rc1
This is a set of fixes for two regressions and one bug in the IOMMU
mapping code. It turns out that all of these issues turn up primarily
on Tegra30 hardware. The IOMMU mapping bug only manifests on buffers
that aren't multiples of the page size. I happened to be testing HDMI
with 1080p while writing the code and framebuffers for that happen to
fit exactly within 2025 pages of 4 KiB each.
One of the regressions is caused by the IOMMU code allocating pages from
shmem which can have associated cache lines. If the pages aren't flushed
then these cache lines may be flushed later on and cause framebuffer
corruption. I'm not sure why I didn't see this before. Perhaps the board
that I was using had enough RAM so that the pages shmem would hand out
had a better chance of being unused. Or maybe I didn't look too closely.
The fix for this is to fake up an SG table so that it can be passed to
the DMA API. Ideally this would use drm_clflush_*(), but implementing
that for ARM causes DRM to fail to build as a module since some of the
low-level cache maintenance functions aren't exported. Hopefully we can
get a suitable API exported on ARM for the next release.
The second regression is caused by a mismatch between the hardware pipe
number and the CRTC's DRM index. These were used inconsistently, which
could cause one code location to call drm_vblank_get() with a different
pipe than the corresponding drm_vblank_put(), thereby causing the
reference count to become unbalanced. Alexandre also reported a possible
race condition related to this, which this series also fixes.
* tag 'drm/tegra/for-3.19-rc1-fixes' of git://people.freedesktop.org/~tagr/linux:
drm/tegra: dc: Select root window for event dispatch
drm/tegra: gem: Use the proper size for GEM objects
drm/tegra: gem: Flush buffer objects upon allocation
drm/tegra: dc: Fix a potential race on page-flip completion
drm/tegra: dc: Consistently use the same pipe
drm/irq: Add drm_crtc_vblank_count()
drm/irq: Add drm_crtc_handle_vblank()
drm/irq: Add drm_crtc_send_vblank_event()
Dave Airlie [Mon, 22 Dec 2014 22:23:08 +0000 (08:23 +1000)]
Merge tag 'drm-intel-next-fixes-2014-12-17' of git://anongit.freedesktop.org/drm-intel into drm-fixes
misc i915 fixes.
* tag 'drm-intel-next-fixes-2014-12-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Disable PSMI sleep messages on all rings around context switches
drm/i915: Force the CS stall for invalidate flushes
drm/i915: Invalidate media caches on gen7
drm/i915: sanitize RPS resetting during GPU reset
drm/i915: move RPS PM_IER enabling to gen6_enable_rps_interrupts
drm/i915: vlv: fix IRQ masking when uninstalling interrupts
Dave Airlie [Mon, 22 Dec 2014 22:22:22 +0000 (08:22 +1000)]
Merge tag 'topic/atomic-fixes-2014-12-17' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Yeah a pull for one patch is a bit overkill but I started to assemble the
various patches for 3.20 in a branch for atomic props/ioctl and didn't
realize that this bugfix here at the beginnning of the branch should be in
3.19 (because msm is using the helpers arleady). So if you'd merge we'd
have it twice or or I need to shuffle branches again. Can do if you want.
* tag 'topic/atomic-fixes-2014-12-17' of git://anongit.freedesktop.org/drm-intel:
drm/atomic: fix potential null ptr on plane enable
Dave Airlie [Mon, 22 Dec 2014 22:21:54 +0000 (08:21 +1000)]
Merge branch 'msm-fixes-3.19' of git://people.freedesktop.org/~robclark/linux into drm-fixes
A few msm fixes for 3.19:
* hdmi regulators fix
* hdmi fix for spurious HPD interrupts
* fix for sync atomic update after async update (which could show
up with a setcrtc following a pageflip)
* couple little Coccinelle cleanups
* 'msm-fixes-3.19' of git://people.freedesktop.org/~robclark/linux:
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
Dave Airlie [Tue, 16 Dec 2014 06:33:09 +0000 (16:33 +1000)]
nouveau: bring back legacy mmap handler
nouveau userspace back at 1.0.1 used to call the X server
DRIOpenDRMMaster interface even for DRI2 (doh!), this attempts
to map the sarea and fails if it can't.
Aaron Lu [Mon, 22 Dec 2014 07:18:05 +0000 (15:18 +0800)]
ACPI / video: Add some Samsung models to disable_native_backlight list
Several Samsung laptop models (SAMSUNG 870Z5E/880Z5E/680Z5E and
SAMSUNG 370R4E/370R4V/370R5E/3570RE/370R5V) do not have a working
native backlight control interface so restore their acpi_videoX
interface.
Nicolas Dichtel [Mon, 22 Dec 2014 17:22:48 +0000 (18:22 +0100)]
tcp6: don't move IP6CB before xfrm6_policy_check()
When xfrm6_policy_check() is used, _decode_session6() is called after some
intermediate functions. This function uses IP6CB(), thus TCP_SKB_CB() must be
prepared after the call of xfrm6_policy_check().
Before this patch, scenarii with IPv6 + TCP + IPsec Transport are broken.
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses") Reported-by: Huaibin Wang <[email protected]> Suggested-by: Eric Dumazet <[email protected]> Signed-off-by: Nicolas Dichtel <[email protected]> Signed-off-by: David S. Miller <[email protected]>
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers caif tries to do a last-ditch check and if there is
more work it will call napi_schedule and then immediately process
some of this new work. Should the entire budget be consumed while
processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in caif.
Amir Vadai [Mon, 22 Dec 2014 08:21:57 +0000 (10:21 +0200)]
net/mlx4_en: Doorbell is byteswapped in Little Endian archs
iowrite32() will byteswap it's argument on big endian archs.
iowrite32be() will byteswap on little endian archs.
Since we don't want to do this unnecessary byteswap on the fast path,
doorbell is stored in the NIC's native endianness. Using the right
iowrite() according to the arch endianness.
Jia-Ju Bai [Mon, 22 Dec 2014 00:43:14 +0000 (08:43 +0800)]
8139too: Add netif_napi_del in the driver
For linux-3.18.0
The driver lacks netif_napi_del in the normal path and error path
to match the call of netif_napi_add in rtl8139_init_one.
This patch fixes this problem.
Jia-Ju Bai [Mon, 22 Dec 2014 00:28:52 +0000 (08:28 +0800)]
8139too: Fix the lack of pci_disable_device
For linux-3.18.0
When pci_request_regions is failed in rtl8139_init_board, pci_disable_device
is not called to disable the device which are enabled by pci_enable_device,
because of disable_dev_on_err is not assigned 1.
This patch fix this problem.
Daniel Glöckner [Sun, 21 Dec 2014 19:27:39 +0000 (20:27 +0100)]
net: s6gmac: remove driver
The s6000 Xtensa support has been removed from the kernel in 4006e565e1500db4. There are no other chips using this driver.
While the Mentor/Alcatel PE-MCXMAC IP core is also used in other
designs (Freescale Gianfar/UCC, QLogic NetXen, Solarflare, Agere
ET-1310, Netlogic XLR/XLS), none of these use this driver as it
heavily depends on the s6000 DMA engine. In fact, there is no
code sharing across any of the aforementioned devices.
tg3: tg3_disable_ints using uninitialized mailbox value to disable interrupts
During driver load in tg3_init_one, if the driver detects DMA activity before
intializing the chip tg3_halt is called. As part of tg3_halt interrupts are
disabled using routine tg3_disable_ints. This routine was using mailbox value
which was not initialized (default value is 0). As a result driver was writing
0x00000001 to pci config space register 0, which is the vendor id / device id.
This driver bug was exposed because of the commit a7877b17a667 (PCI: Check only
the Vendor ID to identify Configuration Request Retry). Also this issue is only
seen in older generation chipsets like 5722 because config space write to offset
0 from driver is possible. The newer generation chips ignore writes to offset 0.
Also without commit a7877b17a667, for these older chips when a GRC reset is
issued the Bootcode would reprogram the vendor id/device id, which is the reason
this bug was masked earlier.
Fixed by initializing the interrupt mailbox registers before calling tg3_halt.
Resolve conflicts between glibc definition of IPV6 socket options
and those defined in Linux headers. Looks like earlier efforts to
solve this did not cover all the definitions.
It resolves warnings during iproute2 build.
Please consider for stable as well.
It is now required that if the entire budget is consumed when poll
returns, the napi poll_list must remain empty. However, like some
other drivers virtio_net tries to do a last-ditch check and if
there is more work it will call napi_schedule and then immediately
process some of this new work. Should the entire budget be consumed
while processing such new work then we will violate the new caller
contract.
This patch fixes this by not touching any work when we reschedule
in virtio_net.
The worst part of this bug is that the list corruption causes other
napi users to be moved off-list. In my case I was chasing a stall
in IPsec (IPsec uses netif_rx) and I only belatedly realised that it
was virtio_net which caused the stall even though the virtio_net
poll was still functioning perfectly after IPsec stalled.
Huacai Chen [Fri, 19 Dec 2014 14:38:18 +0000 (22:38 +0800)]
stmmac: Don't init ptp again when resume from suspend/hibernation
Both stmmac_open() and stmmac_resume() call stmmac_hw_setup(), and
stmmac_hw_setup() call stmmac_init_ptp() unconditionally. However, only
stmmac_release() calls stmmac_release_ptp(). Since stmmac_suspend()
doesn't call stmmac_release_ptp(), stmmac_resume() also needn't call
stmmac_init_ptp().
This patch also fix a "scheduling while atomic" problem when resume
from suspend/hibernation. Because stmmac_init_ptp() will trigger
scheduling while stmmac_resume() hold a spinlock.
Dan Collins [Fri, 19 Dec 2014 03:49:25 +0000 (16:49 +1300)]
packet: Fixed TPACKET V3 to signal poll when block is closed rather than every packet
Make TPACKET_V3 signal poll when block is closed rather than for every
packet. Side effect is that poll will be signaled when block retire
timer expires which didn't previously happen. Issue was visible when
sending packets at a very low frequency such that all blocks are retired
before packets are received by TPACKET_V3. This caused avoidable packet
loss. The fix ensures that the signal is sent when blocks are closed
which covers the normal path where the block is filled as well as the
path where the timer expires. The case where a block is filled without
moving to the next block (ie. all blocks are full) will still cause poll
to be signaled.
Nakajima Akira [Fri, 19 Dec 2014 06:38:14 +0000 (15:38 +0900)]
cifs: make new inode cache when file type is different
In spite of different file type,
if file is same name and same inode number, old inode cache is used.
This causes that you can not cd directory, can not cat SymbolicLink.
So this patch is that if file type is different, return error.
Reproducible sample :
1. create file 'a' at cifs client.
2. repeat rm and mkdir 'a' 4 times at server, then direcotry 'a' having same inode number is created.
(Repeat 4 times, then same inode number is recycled.)
(When server is under RHEL 6.6, 1 time is O.K. Always same inode number is recycled.)
3. ls -li at client, then you can not cd directory, can not remove directory.
execveat.c: In function 'check_execveat_pathmax':
execveat.c:183: warning: format '%lu' expects type 'long unsigned int', but argument 3 has type 'size_t'
execveat.c:187: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'size_t'
Paul Moore [Mon, 22 Dec 2014 17:27:39 +0000 (12:27 -0500)]
audit: correctly record file names with different path name types
There is a problem with the audit system when multiple audit records
are created for the same path, each with a different path name type.
The root cause of the problem is in __audit_inode() when an exact
match (both the path name and path name type) is not found for a
path name record; the existing code creates a new path name record,
but it never sets the path name in this record, leaving it NULL.
This patch corrects this problem by assigning the path name to these
newly created records.
There are many ways to reproduce this problem, but one of the
easiest is the following (assuming auditd is running):
Afterwards, or while the commands above are running, check the audit
log and pay special attention to the PATH records. A faulty kernel
will display something like the following for the file creation:
This issue was brought up by a number of people, but special credit
should go to [email protected] for reporting the problem along
with an explanation of the problem and a patch. While the original
patch did have some problems (see the archive link below), it did
demonstrate the problem and helped kickstart the fix presented here.
Jarkko Nikula [Mon, 22 Dec 2014 14:49:19 +0000 (16:49 +0200)]
ASoC: Intel: Fix BYTCR firmware name
BYTCR DSP firmware is in intel/ subdirectory. See linux-firmware.git
commit d562a3b63632 ("linux-firmware: add sst audio firmware for baytrail
platforms").
Andrew Jackson [Fri, 19 Dec 2014 16:18:06 +0000 (16:18 +0000)]
ASoC: dwc: Iterate over all channels
The Designware core can be configured with up to four stereo channels.
Each stereo channel is individually configured so, when the driver's
hw_params call is made, each requested stereo channel has to be
programmed.
Andrew Jackson [Fri, 19 Dec 2014 16:18:05 +0000 (16:18 +0000)]
ASoC: dwc: Ensure FIFOs are flushed to prevent channel swap
Flush the FIFOs when the stream is prepared for use. This avoids
an inadvertent swapping of the left/right channels if the FIFOs are
not empty at startup.
Jarkko Nikula [Thu, 18 Dec 2014 14:40:35 +0000 (16:40 +0200)]
ASoC: Intel: Add I2C dependency to two new machines
Fix following build error when CONFIG_I2C is not enabled:
sound/soc/codecs/rt5640.c:2252:1: warning: data definition has no type or storage class
module_i2c_driver(rt5640_i2c_driver);
^
sound/soc/codecs/rt5640.c:2252:1: error: type defaults to ‘int’ in declaration of ‘module_i2c_driver’ [-Werror=implicit-int]
sound/soc/codecs/rt5640.c:2252:1: warning: parameter names (without types) in function declaration
sound/soc/codecs/rt5640.c:2241:26: warning: ‘rt5640_i2c_driver’ defined but not used [-Wunused-variable]
static struct i2c_driver rt5640_i2c_driver = {
^
cc1: some warnings being treated as errors
Rabin Vincent [Fri, 19 Dec 2014 12:36:08 +0000 (13:36 +0100)]
crypto: af_alg - fix backlog handling
If a request is backlogged, it's complete() handler will get called
twice: once with -EINPROGRESS, and once with the final error code.
af_alg's complete handler, unlike other users, does not handle the
-EINPROGRESS but instead always completes the completion that recvmsg()
is waiting on. This can lead to a return to user space while the
request is still pending in the driver. If userspace closes the sockets
before the requests are handled by the driver, this will lead to
use-after-frees (and potential crashes) in the kernel due to the tfm
having been freed.
The crashes can be easily reproduced (for example) by reducing the max
queue length in cryptod.c and running the following (from
http://www.chronox.de/libkcapi.html) on AES-NI capable hardware:
Catalin Marinas [Thu, 18 Dec 2014 17:13:49 +0000 (17:13 +0000)]
arm64: Replace set_arch_dma_coherent_ops with arch_setup_dma_ops
Commit a3a60f81ee6f (dma-mapping: replace set_arch_dma_coherent_ops with
arch_setup_dma_ops) changes the of_dma_configure() arch dma_ops callback
to arch_setup_dma_ops but only the arch/arm code is updated. Subsequent
commit 97890ba9289c (dma-mapping: detect and configure IOMMU in
of_dma_configure) changes the arch_setup_dma_ops() prototype further to
handle iommu. The patch makes the corresponding arm64 changes.
Corey Minyard [Sat, 13 Dec 2014 01:06:07 +0000 (19:06 -0600)]
ipmi: Finish cleanup of BMC attributes
The previous cleanup of BMC attributes left a few holes, and if
you run with lockdep debugging with a BMC with the proper attributes,
you could get a warning.
This patch removes all the unused attributes from the BMC structure,
since they are all declared in the .data section now. It makes
the attributes all static. It fixes the referencing of the
attributes in a couple of cases that dynamically added the files
depending on BMC information.
Jan Kara [Fri, 19 Dec 2014 13:27:55 +0000 (14:27 +0100)]
udf: Check component length before reading it
Check that length specified in a component of a symlink fits in the
input buffer we are reading. Also properly ignore component length for
component types that do not use it. Otherwise we read memory after end
of buffer for corrupted udf image.
Javi Merino [Mon, 15 Dec 2014 16:55:52 +0000 (16:55 +0000)]
thermal: cpu_cooling: document node in struct cpufreq_cooling_device
The node field of struct cpufreq_cooling_device was reintroduced in 2dcd851fe4b4 (thermal: cpu_cooling: Update always cpufreq policy with
thermal constraints) but without the documentation that it once had.
Add it back so that all the fields of struct cpufreq_cooling_device
are documented.
Gregory CLEMENT [Wed, 17 Dec 2014 17:07:23 +0000 (18:07 +0100)]
ARM: mvebu: Fix pinctrl configuration for Armada 370 DB
The commit b4607572ef86 (ARM: mvebu: remove conflicting muxing on
Armada 370 DB) removes the hog pins muxing. As it is explained in the
commit log it solves a warning a boot time, but more important it also
allows using the Giga port 0 of the board.
Unfortunately in the same time the commit 4904a82a9399 (arm: mvebu:
move Armada 370/XP pinctrl node definition armada-370-xp.dtsi) was
merged and it introduced again the hog pins muxing. Because of it, the
Giga port 0 of the board is no more usable.
This commit remove again the conflicting muxing (hopefully for the
last time).
Kalle Valo [Sun, 21 Dec 2014 10:39:58 +0000 (12:39 +0200)]
Merge tag 'iwlwifi-fixes-for-kalle-2014-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
I have here new device IDs and a fix for double free bug I introduced.
I also fix an issue with the RFKILL interrupt - the HW needs us to ACK
the interrupt again after we reset it.
Liad fixes an issue with the firmware debugging infrastructure.
While working on torture scenarios of firmware restarts, Eliad found an
issue which he fixed.
Linus Torvalds [Sun, 21 Dec 2014 00:48:59 +0000 (16:48 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux
Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
"kernel: Provide READ_ONCE and ASSIGN_ONCE
As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
ACCESS_ONCE might fail with specific compilers for non-scalar
accesses.
Here is a set of patches to tackle that problem.
The first patch introduce READ_ONCE and ASSIGN_ONCE. If the data
structure is larger than the machine word size memcpy is used and a
warning is emitted. The next patches fix up several in-tree users of
ACCESS_ONCE on non-scalar types.
This does not yet contain a patch that forces ACCESS_ONCE to work only
on scalar types. This is targetted for the next merge window as Linux
next already contains new offenders regarding ACCESS_ONCE vs.
non-scalar types"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
s390/kvm: REPLACE barrier fixup with READ_ONCE
arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
mips/gup: Replace ACCESS_ONCE with READ_ONCE
x86/gup: Replace ACCESS_ONCE with READ_ONCE
x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
mm: replace ACCESS_ONCE with READ_ONCE or barriers
kernel: Provide READ_ONCE and ASSIGN_ONCE
Linus Torvalds [Sun, 21 Dec 2014 00:42:36 +0000 (16:42 -0800)]
Merge tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
Linus Torvalds [Sat, 20 Dec 2014 21:52:52 +0000 (13:52 -0800)]
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
Linus Torvalds [Sat, 20 Dec 2014 21:42:57 +0000 (13:42 -0800)]
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Linus Torvalds [Sat, 20 Dec 2014 21:37:44 +0000 (13:37 -0800)]
Merge tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
"This removes the last few uses of CONFIG_PM_RUNTIME introduced
recently and makes that config option finally go away.
CONFIG_PM will be available directly from the menu now and also it
will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
is set"
* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Eliminate CONFIG_PM_RUNTIME
tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
Linus Torvalds [Sat, 20 Dec 2014 21:33:03 +0000 (13:33 -0800)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"There are only a few things in the misc branch:
- Fix for bugon.cocci semantic patch
- Kdevelop4 files are .gitignored
- Put make binrpm-pkg on diet"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/package: binrpm-pkg do not create source and devel package
.gitignore: Add Kdevelop4 project files
bugon.cocci: fix Options at the macro
Linus Torvalds [Sat, 20 Dec 2014 21:31:14 +0000 (13:31 -0800)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
"Here are the kbuild changes for v3.19-rc1:
- Cleanups and deduplication in the main Makefile and
scripts/Makefile.*
- Sort the output of *config targets in make help
- Old <linux/version.h> is always removed to avoid a surprise during
bisecting
- Warning fix in kconfig"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: remove redundant -rR flag of hdr-inst
kbuild: Fix make help-<board series> on powerpc
kbuild: Automatically remove stale <linux/version.h> file
kconfig: Fix warning "‘jump’ may be used uninitialized"
Makefile: sort list of defconfig targets in make help output
kbuild: Remove duplicate $(cmd) definition in Makefile.clean
kbuild: collect shorthands into scripts/Kbuild.include
Linus Torvalds [Sat, 20 Dec 2014 02:19:19 +0000 (18:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile #3 from Al Viro:
"Assorted fixes and patches from the last cycle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
[regression] chunk lost from bd9b51
vfs: make mounts and mountstats honor root dir like mountinfo does
vfs: cleanup show_mountinfo
init: fix read-write root mount
unfuck binfmt_misc.c (broken by commit e6084d4)
vm_area_operations: kill ->migrate()
new helper: iter_is_iovec()
move_extent_per_page(): get rid of unused w_flags
lustre: get rid of playing with ->fs
btrfs: filp_open() returns ERR_PTR() on failure, not NULL...
Linus Torvalds [Sat, 20 Dec 2014 02:15:12 +0000 (18:15 -0800)]
Merge tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs fixes from Tyler Hicks:
"Fixes for filename decryption and encrypted view plus a cleanup
- The filename decryption routines were, at times, writing a zero
byte one character past the end of the filename buffer
- The encrypted view feature attempted, and failed, to roll its own
form of enforcing a read-only mount instead of letting the VFS
enforce it"
* tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Remove buggy and unnecessary write in file name decode routine
eCryptfs: Remove unnecessary casts when parsing packet lengths
eCryptfs: Force RO mount when encrypted view is enabled
Linus Torvalds [Sat, 20 Dec 2014 02:10:42 +0000 (18:10 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This is part two of our merge window patches.
These are all from Filipe, and fix some really hard to find races that
can cause corruptions. Most of them involved block group removal
(balance) or discard"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: remove non-sense btrfs_error_discard_extent() function
Btrfs: fix fs corruption on transaction abort if device supports discard
Btrfs: always clear a block group node when removing it from the tree
Btrfs: ensure deletion from pinned_chunks list is protected
Linus Torvalds [Sat, 20 Dec 2014 02:07:17 +0000 (18:07 -0800)]
Merge tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have landed after the previous pull request.
All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync"
* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
ALSA: hda/realtek - New codec support for ALC298
ALSA: asihpi: update to HPI version 4.14
ALSA: asihpi: increase tuner pad cache size
ALSA: asihpi: relax firmware version check
ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
ALSA: hda - Add quirk for Packard Bell EasyNote MX65
ALSA: usb-audio: add native DSD support for Matrix Audio DACs
ALSA: hda/realtek - New codec support for ALC256
ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
ASoC: Intel: fix possible acpi enumeration panic
ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
ASoC: Intel: fix return value check in sst_acpi_probe()
ALSA: hda - Make add_stereo_mix_input flag tristate
ALSA: hda - Create capture source ctls when stereo mix input is added
ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
ALSA: hda - add codec ID for Skylake display audio codec
ALSA: oxfw: some signedness bugs
ALSA: oxfw: fix detect_loud_models() return value
ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
...
Linus Torvalds [Sat, 20 Dec 2014 02:02:22 +0000 (18:02 -0800)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
Linus Torvalds [Sat, 20 Dec 2014 01:57:51 +0000 (17:57 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel
Pull arch/hexagon updates from Richard Kuo:
"Build cleanup and a few misc fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Hexagon: fix signal delivery for debug traps
Hexagon: set ARCH_DMA_MINALIGN
Hexagon: fix alignment of init_task in RW_DATA_SECTION
hexagon: Fix build failures in linux-next
Linus Torvalds [Sat, 20 Dec 2014 01:08:14 +0000 (17:08 -0800)]
Merge tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/chris updates from Jesper Nilsson:
"Mostly cleanup and build fixes for CRISv32 allmodconfig
God Jul och Gott Nytt år!"
* tag 'cris-changes-for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
CRISv32: Remove last remnants of ETRAX_SPI_MMC_BOARD
CRISv32: ETRAXFS: Fix recursive spinlock
CRISv32: Select MTDRAM for axisflashmap
CRISv32: Implement early console
CRIS: Use KALLSYMs if available in call stack dump
CRISv32: Fix declaration mismatch
CRISv32: Rewrite of synchronous serial port driver
CRIS: Update init memory handling
CRISv32: Better handling of watchdog bite
CRIS: Export missing function symbols
CRIS: Export ioremap_nocache
CRIS: Fix headers_install
CRISv32: Add missing include for mm.h
CRISv32: Drop obsolete file for SPI driver
audit: use supplied gfp_mask from audit_buffer in kauditd_send_multicast_skb
Eric Paris explains: Since kauditd_send_multicast_skb() gets called in
audit_log_end(), which can come from any context (aka even a sleeping context)
GFP_KERNEL can't be used. Since the audit_buffer knows what context it should
use, pass that down and use that.
Paul Moore [Fri, 19 Dec 2014 23:35:53 +0000 (18:35 -0500)]
audit: don't attempt to lookup PIDs when changing PID filtering audit rules
Commit f1dc4867 ("audit: anchor all pid references in the initial pid
namespace") introduced a find_vpid() call when adding/removing audit
rules with PID/PPID filters; unfortunately this is problematic as
find_vpid() only works if there is a task with the associated PID
alive on the system. The following commands demonstrate a simple
reproducer.
This patch resolves the problem by simply using the PID provided by
the user without any additional validation, e.g. no calls to check to
see if the task/PID exists.
Jesper Nilsson [Tue, 7 Oct 2014 10:20:47 +0000 (12:20 +0200)]
CRIS: Export missing function symbols
strcmp was lost when all other string functions were removed,
but we still have an optimized version for this on CRISv32,
so any driver built as a module would not have access to this symbol.
In a similar manner, we had optimized versions of
csum_partial_copy_from_user and __do_clear_user
but no exported symbols for them, breaking bunch of other drivers
when built as a module.
At the same time, move EXPORT_SYMBOL(__copy_user) and
EXPORT_SYMBOL(__copy_user_zeroing) C-files so it's
located together with the function definition.
Sam Ravnborg [Mon, 14 Jul 2014 15:08:29 +0000 (17:08 +0200)]
CRIS: Fix headers_install
Fix headers_install by adjusting the path to arch files.
And delete unused Kbuild file.
Drop special handling of cris in the headers.sh script
as a nice side-effect.
arch/cris/arch-v32/kernel/time.c: In function 'reset_watchdog':
arch/cris/arch-v32/kernel/time.c:121:2:
error: implicit declaration of function 'global_page_state'
Linus Torvalds [Fri, 19 Dec 2014 22:02:02 +0000 (14:02 -0800)]
Merge branch 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Prarit Bhargava [Sun, 14 Dec 2014 14:06:38 +0000 (09:06 -0500)]
tools / cpupower: Fix no idle state information return value
sysfs_get_idlestate_count() returns an unsigned int. Returning -ENODEV
is not the right thing to do here, and in any case is handled the same
way as if there are no states found.
Michal Privoznik [Sun, 14 Dec 2014 12:36:52 +0000 (13:36 +0100)]
tools / cpupower: Correctly detect if running as root
Some operations, like frequency-set, need root privileges. However,
the way that this is detected is not correct. The getuid() is called,
while in fact geteuid() should be. This way we can allow
distributions or users to set SETUID flags on the cpupower binary if
they want to and let regular users change the cpu frequency governor.
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
The root cause is a race conditon -- cpufreq core and acpi-cpufreq driver
were initiated, but cpufreq_governor wasn't and _PPC changed notification
happened, __cpufreq_governor() was called within acpi_os_execute_deferred
kernel thread context.
To fix this panic issue, add pointer checking code in __cpufreq_governor()
before pointer policy->governor is to be dereferenced.
Linus Torvalds [Fri, 19 Dec 2014 21:29:20 +0000 (13:29 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull NOHZ update from Thomas Gleixner:
"Remove the call into the nohz idle code from the fake 'idle' thread in
the powerclamp driver along with the export of those functions which
was smuggeled in via the thermal tree. People have tried to hack
around it in the nohz core code, but it just violates all rightful
assumptions of that code about the only valid calling context (i.e.
the proper idle task).
The powerclamp trainwreck will still work, it just wont get the
benefit of long idle sleeps"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/powerclamp: Remove tick_nohz_idle abuse
Linus Torvalds [Fri, 19 Dec 2014 21:26:08 +0000 (13:26 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq core fix from Thomas Gleixner:
"A single fix plugging a long standing race between proc/stat and
proc/interrupts access and freeing of interrupt descriptors"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Prevent proc race against freeing of irq descriptors
Linus Torvalds [Fri, 19 Dec 2014 21:22:42 +0000 (13:22 -0800)]
Merge branch 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 MPX fixes from Thomas Gleixner:
"Three updates for the new MPX infrastructure:
- Use the proper error check in the trap handler
- Add a proper config option for it
- Bring documentation up to date"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mpx: Give MPX a real config option prompt
x86, mpx: Update documentation
x86_64/traps: Fix always true condition
Linus Torvalds [Fri, 19 Dec 2014 21:15:24 +0000 (13:15 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes and cleanups from Ingo Molnar:
"A kernel fix plus mostly tooling fixes, but also some tooling
restructuring and cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
perf: Fix building warning on ARM 32
perf symbols: Fix use after free in filename__read_build_id
perf evlist: Use roundup_pow_of_two
tools: Adopt roundup_pow_of_two
perf tools: Make the mmap length autotuning more robust
tools: Adopt rounddown_pow_of_two and deps
tools: Adopt fls_long and deps
tools: Move bitops.h from tools/perf/util to tools/
tools: Introduce asm-generic/bitops.h
tools lib: Move asm-generic/bitops/find.h code to tools/include and tools/lib
tools: Whitespace prep patches for moving bitops.h
tools: Move code originally from asm-generic/atomic.h into tools/include/asm-generic/
tools: Move code originally from linux/log2.h to tools/include/linux/
tools: Move __ffs implementation to tools/include/asm-generic/bitops/__ffs.h
perf evlist: Do not use hard coded value for a mmap_pages default
perf trace: Let the perf_evlist__mmap autosize the number of pages to use
perf evlist: Improve the strerror_mmap method
perf evlist: Clarify sterror_mmap variable names
perf evlist: Fixup brown paper bag on "hint" for --mmap-pages cmdline arg
perf trace: Provide a better explanation when mmap fails
...
Linus Torvalds [Fri, 19 Dec 2014 20:57:45 +0000 (12:57 -0800)]
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
projects / linux.git / log