accel/ivpu: Use ratelimited warn and err in IPC/JSM
Quite often during test corner cases IPC, JSM functions can flood
dmesg with warn or err messages. With that lost dmesg history.
Change warn, err to ratelimited versions in IPC, JSM to suppress
dmesg spam occurrence during fail test scenarios.
Cong Yang [Fri, 13 Oct 2023 09:18:44 +0000 (17:18 +0800)]
arm64: defconfig: Enable ILITEK_ILI9882T panel
DRM_PANEL_ILITEK_ILI9882T is being split out from
DRM_PANEL_BOE_TV101WUM_NL6. Since the arm64 defconfig had the BOE
panel driver enabled, let's also enable the Ilitek driver.
Cong Yang [Fri, 13 Oct 2023 09:18:43 +0000 (17:18 +0800)]
drm/panel: ili9882t: Avoid blurred screen from fast sleep
At present, we have found that there may be a problem of blurred
screen during fast sleep/resume. The direct cause of the blurred
screen is that the IC does not receive 0x28/0x10. Because of the
particularity of the IC, before the panel enters sleep hid must
stop scanning, as i2c_hid_core_suspend before ili9882t_disable.
If move the ili9882t_enter_sleep_mode function to ili9882t_unprepare,
touch reset will pull low before panel entersleep, which does not meet
the timing requirements.. So in order to solve this problem, the IC
can handle it through the exception mechanism when it cannot receive
0x28/0x10 command. Handling exceptions requires a reset 50ms delay.
Refer to vendor detailed analysis [1].
Ilitek vendor also suggested switching the page before entering sleep to
avoid panel IC not receiving 0x28/0x10 command.
Cong Yang [Fri, 13 Oct 2023 09:18:42 +0000 (17:18 +0800)]
drm/panel: ili9882t: Break out as separate driver
The Starry ILI9882t-based panel should never have been part of the boe
tv101wum driver, it is clearly based on the Ilitek ILI9882t display
controller and if you look at the custom command sequences for the
panel these clearly contain the signature Ilitek page switch (0xff)
commands. The hardware has nothing in common with the other panels
supported by this driver.
Break this out into a separate driver and config symbol instead.
If the placement here is out of convenience for using similar code,
we should consider creating a helper library instead.
fbdev/vt8623fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/viafb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/vga16fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/vermilionfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/tridentfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/tgafb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/tdfxfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/sunxvr500: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/stifb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/sm712fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/sm501fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize each instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/sisfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/savagefb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/sa1100fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/s3fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/s1d13xxxfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
To simplify the conversion, provide a dedicated fb_ops instance
for accelerated devices. No functional changes.
fbdev/rivafb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/radeon: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/pvr2fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/pm3fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/pm2fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/omapfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/nvidiafb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/neofb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/matroxfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize each instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/intelfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/imsttfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/i810fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/hpfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/hitfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/hgafb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/gbefb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/ep93xx-fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/dnfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/cyber2000fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/controlfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/cobalt-lcd: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/cirrusfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/au1100fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/atyfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/atafb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/arkfb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/amifb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/amba-clcd: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
fbdev/68328fb: Initialize fb_ops to fbdev I/O-memory helpers
Initialize the instance of struct fb_ops with fbdev initializer
macros for framebuffers in I/O address space. Set the read/write,
draw and mmap callbacks to the correct implementation and avoid
implicit defaults. Also select the necessary I/O helpers in Kconfig.
Fbdev drivers sometimes rely on the callbacks being NULL for a
default implementation to be invoked; hence requiring the I/O
helpers to be built in any case. Setting all callbacks in all
drivers explicitly will allow to make the I/O helpers optional.
This benefits systems that do not use these functions.
Provide helpers for accessing I/O memory in a helper module. The fbdev
core uses these helpers, so select the module unconditionally for fbdev.
Drivers will later be able to select the module individually and the
helpers will become optional.
dt-bindings: display: Split common Solomon properties in their own schema
There are DT properties that can be shared across different Solomon OLED
Display Controller families. Split them into a separate common schema to
avoid these properties to be duplicated in different DT bindings schemas.
drm/ssd130x: Add support for the SSD132x OLED controller family
The Solomon SSD132x controllers (such as the SSD1322, SSD1325 and SSD1327)
are used by 16 grayscale dot matrix OLED panels, extend the driver to also
support this chip family.
Instead adding an indirection level to allow the same modesetting pipeline
to be used by both controller families, add another pipeline for SSD132x.
This leads to some code duplication but it makes the driver easier to read
and reason about. Once other controller families are added (e.g: SSD133x),
some common code can be factored out in driver helpers to be shared by the
different families. But that can be done later once these patterns emerge.
drm/ssd130x: Replace .page_height field in device info with a constant
This deemed useful to avoid hardcoding a page height and allow to support
other Solomon controller families, but dividing the screen in pages seems
to be something that is specific to the SSD130x chip family.
For example, SSD132x chip family divides the screen in segments (columns)
and common outputs (rows), so the concept of screen pages does not exist
for the SSD132x family.
Let's drop this field from the device info struct and just use a constant
SSD130X_PAGE_HEIGHT macro to define the page height. While being there,
replace hardcoded 8 values in places where it is used as the page height.
Thomas Hellström [Tue, 10 Oct 2023 14:27:24 +0000 (16:27 +0200)]
drm/gpuvm: Dual-licence the drm_gpuvm code GPL-2.0 OR MIT
Dual-licence in order to make it possible for other non-GPL os'es
to re-implement the code. The use of EXPORT_SYMBOL_GPL() is intentionally
left untouched to prevent use of drm_gpuvm as a proxy for non-GPL drivers
to access GPL-only kernel symbols.
Much of the ideas and algorithms used in the drm_gpuvm code is already
present in one way or another in MIT-licensed code.
Thomas Hellström [Thu, 12 Oct 2023 13:25:52 +0000 (15:25 +0200)]
Documentation/gpu: Add a VM_BIND async document
Add a motivation for and description of asynchronous VM_BIND operation
v2:
- Fix typos (Nirmoy Das)
- Improve the description of a memory fence (Oak Zeng)
- Add a reference to the document in the Xe RFC.
- Add pointers to sample uAPI suggestions
v3:
- Address review comments (Danilo Krummrich)
- Formatting fixes
v4:
- Address typos (Francois Dugast)
- Explain why in-fences are not allowed for VM_BIND operations for long-
running workloads (Matthew Brost)
v5:
- More typo- and style fixing
- Further clarify the implications of disallowing in-fences for VM_BIND
operations for long-running workloads (Matthew Brost)
v6:
- Point out that a gpu_vm is a virtual GPU Address space.
(Danilo Krummrich)
- For an explanation of dma-fences point to the dma-fence documentation.
(Paulo Zanoni)
- Clarify that VM_BIND errors are reported synchronously. (Paulo Zanoni)
- Use an rst doc reference when pointing to the async vm_bind document
from the xe merge plan.
- Add the VM_BIND documentation to the drm documentation table-of-content,
using an intermediate "Misc DRM driver uAPI- and feature implementation
guidelines"
v7:
- Update the error handling documentation to remove the VM error state.
v8:
- Clarify error handling and difference in operation support between
async VM_BIND and sync VM_BIND. (Paulo Zanoni)
- Update the sample uAPI with a self-contained example. (Paulo Zanoni)
The Powkiddy RGB30 panel is a 4 inch 720x720 MIPI-DSI LCD panel. It
appears to be based on the ST7703 LCD controller (this is assumed from
the init sequence similarity between this and other displays). Powkiddy
would not share the part number or name for the display from the bill
of materials and there were no obvious external markings, so name the
panel for the device (Powkiddy RGB30).
Dan Carpenter [Wed, 11 Oct 2023 08:01:48 +0000 (11:01 +0300)]
drm/rockchip: Fix type promotion bug in rockchip_gem_iommu_map()
The "ret" variable is declared as ssize_t and it can hold negative error
codes but the "rk_obj->base.size" variable is type size_t. This means
that when we compare them, they are both type promoted to size_t and the
negative error code becomes a high unsigned value and is treated as
success. Add a cast to fix this.
Dmitry Baryshkov [Wed, 11 Oct 2023 22:00:02 +0000 (01:00 +0300)]
drm/bridge: lt9611uxc: fix the race in the error path
If DSI host attachment fails, the LT9611UXC driver will remove the
bridge without ensuring that there is no outstanding HPD work being
done. In rare cases this can result in the warnings regarding the mutex
being incorrect. Fix this by forcebly freing IRQ and flushing the work.
Liu Ying [Mon, 21 Aug 2023 03:40:08 +0000 (11:40 +0800)]
drm/bridge: imx: Add i.MX93 MIPI DSI support
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Add a DRM bridge for i.MX93 MIPI DSI by using existing DW MIPI DSI
bridge helpers and implementing i.MX93 MIPI DSI specific extensions.
Freescale i.MX93 SoC embeds a Synopsys Designware MIPI DSI host
controller and a Synopsys Designware MIPI DPHY. Some configurations
and extensions to them are controlled by i.MX93 media blk-ctrl.
Liu Ying [Mon, 21 Aug 2023 03:40:06 +0000 (11:40 +0800)]
drm/bridge: synopsys: dw-mipi-dsi: Disable HSTX and LPRX timeout check
According to Synopsys DW MIPI DSI host databook, HSTX and LPRX timeout
contention detections are measured in TO_CLK_DIVISION cycles. However,
the current driver programs magic values to TO_CLK_DIVISION, HSTX_TO_CNT
and LPRX_TO_CNT register fields, which makes timeout error event wrongly
happen for some video modes, at least for the typical 1920x1080p@60 video
mode read from a HDMI monitor driven by ADV7535 DSI to HDMI bridge.
While at it, the current driver doesn't enable interrupt to handle or
complain about the error status, so true error just happens silently
except for display distortions by visual check.
Disable the timeout check by setting those timeout register fields to
zero for now until someone comes along with better computations for the
timeout values. Although the databook doesn't mention what happens when
they are set to zero, it turns out the false error doesn't happen for
the 1920x1080p@60 video mode at least.
Liu Ying [Mon, 21 Aug 2023 03:40:05 +0000 (11:40 +0800)]
drm/bridge: synopsys: dw-mipi-dsi: Set minimum lane byte clock cycles for HSA and HBP
According to Synopsys support channel, each region of HSA, HBP and HFP must
have minimum number of 10 bytes where constant 4 bytes are for HSS or HSE
and 6 bytes are for blanking packet(header + CRC). Hence, the below table
comes in.
Implement the minimum lbcc numbers to make sure that the values programmed
into DSI_VID_HSA_TIME and DSI_VID_HBP_TIME registers meet the minimum
number requirement. For DSI_VID_HLINE_TIME register, it seems that the
value programmed should be based on mode->htotal as-is, instead of sum up
HSA, HBP, HFP and HDISPLAY.
This helps the case where Raydium RM67191 DSI panel is connected, since
it's video timing for hsync length is only 2 pixels and without this patch
the programmed value for DSI_VID_HSA_TIME is only 2 with 4 data lanes.
Liu Ying [Mon, 21 Aug 2023 03:40:04 +0000 (11:40 +0800)]
drm/bridge: synopsys: dw-mipi-dsi: Use pixel clock rate to calculate lbcc
To get better accuration, use pixel clock rate to calculate lbcc instead of
lane_mbps since the pixel clock rate is in KHz while lane_mbps is in MHz.
Without this, distorted image can be seen on a HDMI monitor connected with
i.MX93 11x11 EVK through ADV7535 DSI to HDMI bridge in 1920x1080p@60 video
mode.
Liu Ying [Mon, 21 Aug 2023 03:40:03 +0000 (11:40 +0800)]
drm/bridge: synopsys: dw-mipi-dsi: Add mode fixup support
Vendor drivers may need to fixup mode due to pixel clock tree limitation,
so introduce the ->mode_fixup() callcack to struct dw_mipi_dsi_plat_data
and call it at atomic check stage if available.
Liu Ying [Mon, 21 Aug 2023 03:40:02 +0000 (11:40 +0800)]
drm/bridge: synopsys: dw-mipi-dsi: Force input bus flags
The DATAEN_ACTIVE_LOW bit in DSI_DPI_CFG_POL register is set to zero,
so set the DRM_BUS_FLAG_DE_HIGH flag in input_bus_cfg.flags. It appears
that the DRM_BUS_FLAG_PIXDATA_SAMPLE_NEGEDGE flag also makes sense, so
set it in input_bus_cfg.flags too. With this patch, the flags set by
drm_atomic_bridge_propagate_bus_flags() are overridden (see comment in
that function) in case any downstream bridges propagates invalid flags
to this bridge. A real problematic case is to connect a RM67191 MIPI
DSI panel whose driver sets DRM_BUS_FLAG_DE_LOW and
DRM_BUS_FLAG_PIXDATA_SAMPLE_POSEDGE bus flags.
Liu Ying [Mon, 21 Aug 2023 03:40:01 +0000 (11:40 +0800)]
drm/bridge: synopsys: dw-mipi-dsi: Add input bus format negotiation support
Introduce ->get_input_bus_fmts() callback to struct dw_mipi_dsi_plat_data
so that vendor drivers can implement specific methods to get input bus
formats for Synopsys DW MIPI DSI.
While at it, implement a generic callback for ->atomic_get_input_bus_fmts(),
where we try to get the input bus formats through pdata->get_input_bus_fmts()
first. If it's unavailable, fall back to the only format - MEDIA_BUS_FMT_FIXED,
which matches the default behavior if ->atomic_get_input_bus_fmts() is not
implemented as ->atomic_get_input_bus_fmts()'s kerneldoc indicates.
Biju Das [Wed, 30 Aug 2023 14:23:58 +0000 (15:23 +0100)]
drm: adv7511: Add hpd_override_enable variable to struct adv7511_chip_info
As per spec, it is allowed to pulse the HPD signal to indicate that the
EDID information has changed. Some monitors do this when they wake up
from standby or are enabled. When the HPD goes low the adv7511 is
reset and the outputs are disabled which might cause the monitor to
go to standby again. To avoid this we ignore the HPD pin for the
first few seconds after enabling the output. On the other hand,
adv7535 require to enable HPD Override bit for proper HPD.
Add hpd_override_enable variable to struct adv7511_chip_info to handle
this scenario.
Biju Das [Wed, 30 Aug 2023 14:23:57 +0000 (15:23 +0100)]
drm: adv7511: Add link_config variable to struct adv7511_chip_info
The ADV7511 needs link configuration whereas ADV75{33,35} does not need
it. Add a variable link_config to struct adv7511_chip_info to handle
this difference.
Biju Das [Wed, 30 Aug 2023 14:23:55 +0000 (15:23 +0100)]
drm: adv7511: Add reg_cec_offset variable to struct adv7511_chip_info
The ADV7533 and ADV7535 have an offset(0x70) for the CEC register map
compared to ADV7511. Add the reg_cec_offset variable to struct
adv7511_chip_info to handle this difference and drop the reg_cec_offset
variable from struct adv7511.
This will avoid assigning reg_cec_offset based on chip type and also
testing for multiple chip types by calling adv7533_patch_cec_registers().
Biju Das [Wed, 30 Aug 2023 14:23:54 +0000 (15:23 +0100)]
drm: adv7511: Add supply_names and num_supplies variables to struct adv7511_chip_info
The ADV7511 has 5 power supplies compared to 7 that of ADV75{33,35}. Add
supply_names and num_supplies variables to struct adv7511_chip_info to
handle this difference.
Biju Das [Wed, 30 Aug 2023 14:23:53 +0000 (15:23 +0100)]
drm: adv7511: Add max_lane_freq_khz variable to struct adv7511_chip_info
The ADV7533 supports a maximum lane clock of 800MHz whereas it is 891MHz
for ADV7535. Add max_lane_freq_khz variable to struct adv7511_chip_info to
handle this difference.
While at it, drop the unused local variable max_lane_freq.
Biju Das [Wed, 30 Aug 2023 14:23:52 +0000 (15:23 +0100)]
drm: adv7511: Add max_mode_clock_khz variable to struct adv7511_chip_info
The ADV7533 supports a maximum pixel clock of 80MHz whereas it is 148.5MHz
for ADV7535. Add max_mode_clock_khz variable to struct adv7511_chip_info to
handle this difference.
Biju Das [Wed, 30 Aug 2023 14:23:51 +0000 (15:23 +0100)]
drm: adv7511: Add struct adv7511_chip_info and use i2c_get_match_data()
Add struct adv7511_chip_info to handle hw differences between various
chips rather checking against the 'type' variable in various places.
Replace 'adv->type'->'info->type' by moving variable 'type' from
struct adv7511 to struct adv7511_chip_info and add adv7511_chip_info as
device data for both OF and ID tables instead of the device type.
Simplify the probe() by replacing of_device_get_match_data() and ID lookup
for retrieving match data with i2c_get_match_data().
Frank Oltmanns [Mon, 13 Feb 2023 12:32:38 +0000 (13:32 +0100)]
drm/panel: st7703: Fix timings when entering/exiting sleep
Fix flickering of the pinephone's XDB599 panel that happens after
resume.
Extend the delay after issuing the command to exit sleep mode from 60 to
120 msec as per the controller's specification.
Introduce a 120 msec delay after issuing the command to enter sleep
mode. This is needed in order for the controller to reliably finalize
the sleep in sequence before switching of power supply.
In contrast to the JH057N panel, the XBD599 panel does not require a 20
msec delay after initialization and exiting sleep mode. Therefore, move
the delay into the already existing device specific initialization
function.
The XDB599 does not require a 20 msec delay between the SETBGP and
SETVCOM commands. Therefore, remove the delay from the device specific
initialization function.
Ondrej Jirman [Sat, 11 Feb 2023 17:17:48 +0000 (18:17 +0100)]
drm/panel: st7703: Pick different reset sequence
Switching to a different reset sequence, enabling IOVCC before enabling
VCC.
There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.
This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).
The plane's atomic_check returns -EINVAL if the CRTC has not been
set. This is the case for disabled planes, for which atomic_check
should return 0. For disabled planes, it also omits the mandatory
call to drm_atomic_helper_check_plane_state().
Replace the test with the boiler-plate code that first invokes
drm_atomic_helper_check_plane_state() and then tests for the plane
to be visible. Return early for non-visible planes.
accel/ivpu: Add ivpu_bo_vaddr() and ivpu_bo_size()
Use:
- ivpu_bo_vaddr(bo) instead of bo->kvaddr
- ivpu_bo_size(bo) instead of bo->base.size
This is a preparation for switch to a drm_gem_shmem_object as a base for
ivpu_bo, where:
- bo->kvaddr becomes bo->base.vaddr
- bo->base.size becomes bo->base.base.size
Using ivpu_bo_vaddr() and ivpu_bo_size() increases the readability of
the code.
projects / linux.git / log