* and has yet to be completed (maybe due to data move, or simply
* awaiting an ack from the core all the data has been completed).
* @debugfs: File entry for debugfs file for this endpoint.
- * @lock: State lock to protect contents of endpoint.
* @dir_in: Set to true if this endpoint is of the IN direction, which
* means that it is sending data to the Host.
* @index: The index for the endpoint registers.
* @mc: Multi Count - number of transactions per microframe
- * @interval - Interval for periodic endpoints, in frames or microframes.
+ * @interval: Interval for periodic endpoints, in frames or microframes.
* @name: The name array passed to the USB core.
* @halted: Set if the endpoint has been halted.
* @periodic: Set if this is a periodic ep, such as Interrupt
* @desc_list_dma: The DMA address of descriptor chain currently in use.
* @desc_list: Pointer to descriptor DMA chain head currently in use.
* @desc_count: Count of entries within the DMA descriptor chain of EP.
- * @isoc_chain_num: Number of ISOC chain currently in use - either 0 or 1.
* @next_desc: index of next free descriptor in the ISOC chain under SW control.
+ * @compl_desc: index of next descriptor to be completed by xFerComplete
* @total_data: The total number of data bytes done.
* @fifo_size: The size of the FIFO (for periodic IN endpoints)
+ * @fifo_index: For Dedicated FIFO operation, only FIFO0 can be used for EP0.
* @fifo_load: The amount of data loaded into the FIFO (periodic IN)
* @last_load: The offset of data for the last start of request.
* @size_loaded: The last loaded size for DxEPTSIZE for periodic IN
struct dwc2_dma_desc *desc_list;
u8 desc_count;
- unsigned char isoc_chain_num;
unsigned int next_desc;
+ unsigned int compl_desc;
char name[10];
};
* is FS.
* 0 - No (default)
* 1 - Yes
+ * @ipg_isoc_en: Indicates the IPG supports is enabled or disabled.
+ * 0 - Disable (default)
+ * 1 - Enable
+ * @acg_enable: For enabling Active Clock Gating in the controller
+ * 0 - No
+ * 1 - Yes
* @ulpi_fs_ls: Make ULPI phy operate in FS/LS mode only
* 0 - No (default)
* 1 - Yes
bool hird_threshold_en;
u8 hird_threshold;
bool activate_stm_fs_transceiver;
+ bool ipg_isoc_en;
u16 max_packet_count;
u32 max_transfer_size;
u32 ahbcfg;
*
* The values that are not in dwc2_core_params are documented below.
*
- * @op_mode Mode of Operation
+ * @op_mode: Mode of Operation
* 0 - HNP- and SRP-Capable OTG (Host & Device)
* 1 - SRP-Capable OTG (Host & Device)
* 2 - Non-HNP and Non-SRP Capable OTG (Host & Device)
* 4 - Non-OTG Device
* 5 - SRP-Capable Host
* 6 - Non-OTG Host
- * @arch Architecture
+ * @arch: Architecture
* 0 - Slave only
* 1 - External DMA
* 2 - Internal DMA
- * @power_optimized Are power optimizations enabled?
- * @num_dev_ep Number of device endpoints available
- * @num_dev_in_eps Number of device IN endpoints available
- * @num_dev_perio_in_ep Number of device periodic IN endpoints
- * available
- * @dev_token_q_depth Device Mode IN Token Sequence Learning Queue
+ * @ipg_isoc_en: This feature indicates that the controller supports
+ * the worst-case scenario of Rx followed by Rx
+ * Interpacket Gap (IPG) (32 bitTimes) as per the utmi
+ * specification for any token following ISOC OUT token.
+ * 0 - Don't support
+ * 1 - Support
+ * @power_optimized: Are power optimizations enabled?
+ * @num_dev_ep: Number of device endpoints available
+ * @num_dev_in_eps: Number of device IN endpoints available
+ * @num_dev_perio_in_ep: Number of device periodic IN endpoints
+ * available
+ * @dev_token_q_depth: Device Mode IN Token Sequence Learning Queue
* Depth
* 0 to 30
- * @host_perio_tx_q_depth
+ * @host_perio_tx_q_depth:
* Host Mode Periodic Request Queue Depth
* 2, 4 or 8
- * @nperio_tx_q_depth
+ * @nperio_tx_q_depth:
* Non-Periodic Request Queue Depth
* 2, 4 or 8
- * @hs_phy_type High-speed PHY interface type
+ * @hs_phy_type: High-speed PHY interface type
* 0 - High-speed interface not supported
* 1 - UTMI+
* 2 - ULPI
* 3 - UTMI+ and ULPI
- * @fs_phy_type Full-speed PHY interface type
+ * @fs_phy_type: Full-speed PHY interface type
* 0 - Full speed interface not supported
* 1 - Dedicated full speed interface
* 2 - FS pins shared with UTMI+ pins
* 3 - FS pins shared with ULPI pins
* @total_fifo_size: Total internal RAM for FIFOs (bytes)
- * @hibernation Is hibernation enabled?
- * @utmi_phy_data_width UTMI+ PHY data width
+ * @hibernation: Is hibernation enabled?
+ * @utmi_phy_data_width: UTMI+ PHY data width
* 0 - 8 bits
* 1 - 16 bits
* 2 - 8 or 16 bits
* @snpsid: Value from SNPSID register
* @dev_ep_dirs: Direction of device endpoints (GHWCFG1)
- * @g_tx_fifo_size[] Power-on values of TxFIFO sizes
+ * @g_tx_fifo_size: Power-on values of TxFIFO sizes
+ * @dma_desc_enable: When DMA mode is enabled, specifies whether to use
+ * address DMA mode or descriptor DMA mode for accessing
+ * the data FIFOs. The driver will automatically detect the
+ * value for this if none is specified.
+ * 0 - Address DMA
+ * 1 - Descriptor DMA (default, if available)
+ * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters
+ * 1 - Allow dynamic FIFO sizing (default, if available)
+ * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs
+ * are enabled for non-periodic IN endpoints in device
+ * mode.
+ * @host_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO
+ * in host mode when dynamic FIFO sizing is enabled
+ * 16 to 32768
+ * Actual maximum value is autodetected and also
+ * the default.
+ * @host_perio_tx_fifo_size: Number of 4-byte words in the periodic Tx FIFO in
+ * host mode when dynamic FIFO sizing is enabled
+ * 16 to 32768
+ * Actual maximum value is autodetected and also
+ * the default.
+ * @max_transfer_size: The maximum transfer size supported, in bytes
+ * 2047 to 65,535
+ * Actual maximum value is autodetected and also
+ * the default.
+ * @max_packet_count: The maximum number of packets in a transfer
+ * 15 to 511
+ * Actual maximum value is autodetected and also
+ * the default.
+ * @host_channels: The number of host channel registers to use
+ * 1 to 16
+ * Actual maximum value is autodetected and also
+ * the default.
+ * @dev_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO
+ * in device mode when dynamic FIFO sizing is enabled
+ * 16 to 32768
+ * Actual maximum value is autodetected and also
+ * the default.
+ * @i2c_enable: Specifies whether to use the I2Cinterface for a full
+ * speed PHY. This parameter is only applicable if phy_type
+ * is FS.
+ * 0 - No (default)
+ * 1 - Yes
+ * @acg_enable: For enabling Active Clock Gating in the controller
+ * 0 - Disable
+ * 1 - Enable
+ * @lpm_mode: For enabling Link Power Management in the controller
+ * 0 - Disable
+ * 1 - Enable
+ * @rx_fifo_size: Number of 4-byte words in the Rx FIFO when dynamic
+ * FIFO sizing is enabled 16 to 32768
+ * Actual maximum value is autodetected and also
+ * the default.
*/
struct dwc2_hw_params {
unsigned op_mode:3;
unsigned hibernation:1;
unsigned utmi_phy_data_width:2;
unsigned lpm_mode:1;
+ unsigned ipg_isoc_en:1;
u32 snpsid;
u32 dev_ep_dirs;
u32 g_tx_fifo_size[MAX_EPS_CHANNELS];
* @gi2cctl: Backup of GI2CCTL register
* @glpmcfg: Backup of GLPMCFG register
* @gdfifocfg: Backup of GDFIFOCFG register
+ * @pcgcctl: Backup of PCGCCTL register
+ * @pcgcctl1: Backup of PCGCCTL1 register
+ * @dtxfsiz: Backup of DTXFSIZ registers for each endpoint
* @gpwrdn: Backup of GPWRDN register
+ * @valid: True if registers values backuped.
*/
struct dwc2_gregs_backup {
u32 gotgctl;
* @doeptsiz: Backup of DOEPTSIZ register
* @doepdma: Backup of DOEPDMA register
* @dtxfsiz: Backup of DTXFSIZ registers for each endpoint
+ * @valid: True if registers values backuped.
*/
struct dwc2_dregs_backup {
u32 dcfg;
* @hcfg: Backup of HCFG register
* @haintmsk: Backup of HAINTMSK register
* @hcintmsk: Backup of HCINTMSK register
- * @hptr0: Backup of HPTR0 register
+ * @hprt0: Backup of HPTR0 register
* @hfir: Backup of HFIR register
* @hptxfsiz: Backup of HPTXFSIZ register
+ * @valid: True if registers values backuped.
*/
struct dwc2_hregs_backup {
u32 hcfg;
* @regs: Pointer to controller regs
* @hw_params: Parameters that were autodetected from the
* hardware registers
- * @core_params: Parameters that define how the core should be configured
+ * @params: Parameters that define how the core should be configured
* @op_state: The operational State, during transitions (a_host=>
* a_peripheral and b_device=>b_host) this may not match
* the core, but allows the software to determine
* - USB_DR_MODE_PERIPHERAL
* - USB_DR_MODE_HOST
* - USB_DR_MODE_OTG
- * @hcd_enabled Host mode sub-driver initialization indicator.
- * @gadget_enabled Peripheral mode sub-driver initialization indicator.
- * @ll_hw_enabled Status of low-level hardware resources.
+ * @hcd_enabled: Host mode sub-driver initialization indicator.
+ * @gadget_enabled: Peripheral mode sub-driver initialization indicator.
+ * @ll_hw_enabled: Status of low-level hardware resources.
* @hibernated: True if core is hibernated
+ * @frame_number: Frame number read from the core. For both device
+ * and host modes. The value ranges are from 0
+ * to HFNUM_MAX_FRNUM.
* @phy: The otg phy transceiver structure for phy control.
* @uphy: The otg phy transceiver structure for old USB phy
* control.
* interrupt
* @wkp_timer: Timer object for handling Wakeup Detected interrupt
* @lx_state: Lx state of connected device
- * @gregs_backup: Backup of global registers during suspend
- * @dregs_backup: Backup of device registers during suspend
- * @hregs_backup: Backup of host registers during suspend
+ * @gr_backup: Backup of global registers during suspend
+ * @dr_backup: Backup of device registers during suspend
+ * @hr_backup: Backup of host registers during suspend
*
* These are for host mode:
*
* @flags: Flags for handling root port state changes
+ * @flags.d32: Contain all root port flags
+ * @flags.b: Separate root port flags from each other
+ * @flags.b.port_connect_status_change: True if root port connect status
+ * changed
+ * @flags.b.port_connect_status: True if device connected to root port
+ * @flags.b.port_reset_change: True if root port reset status changed
+ * @flags.b.port_enable_change: True if root port enable status changed
+ * @flags.b.port_suspend_change: True if root port suspend status changed
+ * @flags.b.port_over_current_change: True if root port over current state
+ * changed.
+ * @flags.b.port_l1_change: True if root port l1 status changed
+ * @flags.b.reserved: Reserved bits of root port register
* @non_periodic_sched_inactive: Inactive QHs in the non-periodic schedule.
* Transfers associated with these QHs are not currently
* assigned to a host channel.
* assigned to a host channel.
* @non_periodic_qh_ptr: Pointer to next QH to process in the active
* non-periodic schedule
+ * @non_periodic_sched_waiting: Waiting QHs in the non-periodic schedule.
+ * Transfers associated with these QHs are not currently
+ * assigned to a host channel.
* @periodic_sched_inactive: Inactive QHs in the periodic schedule. This is a
* list of QHs for periodic transfers that are _not_
* scheduled for the next frame. Each QH in the list has an
* @hs_periodic_bitmap: Bitmap used by the microframe scheduler any time the
* host is in high speed mode; low speed schedules are
* stored elsewhere since we need one per TT.
- * @frame_number: Frame number read from the core at SOF. The value ranges
- * from 0 to HFNUM_MAX_FRNUM.
* @periodic_qh_count: Count of periodic QHs, if using several eps. Used for
* SOF enable/disable.
* @free_hc_list: Free host channels in the controller. This is a list of
* host channel is available for non-periodic transactions.
* @non_periodic_channels: Number of host channels assigned to non-periodic
* transfers
- * @available_host_channels Number of host channels available for the microframe
- * scheduler to use
+ * @available_host_channels: Number of host channels available for the
+ * microframe scheduler to use
* @hc_ptr_array: Array of pointers to the host channel descriptors.
* Allows accessing a host channel descriptor given the
* host channel number. This is useful in interrupt
* @dedicated_fifos: Set if the hardware has dedicated IN-EP fifos.
* @num_of_eps: Number of available EPs (excluding EP0)
* @debug_root: Root directrory for debugfs.
- * @debug_file: Main status file for debugfs.
- * @debug_testmode: Testmode status file for debugfs.
- * @debug_fifo: FIFO status file for debugfs.
* @ep0_reply: Request used for ep0 reply.
* @ep0_buff: Buffer for EP0 reply data, if needed.
* @ctrl_buff: Buffer for EP0 control requests.
* @ctrl_in_desc: EP0 IN data phase desc chain pointer
* @ctrl_out_desc_dma: EP0 OUT data phase desc chain DMA address
* @ctrl_out_desc: EP0 OUT data phase desc chain pointer
- * @eps: The endpoints being supplied to the gadget framework
+ * @irq: Interrupt request line number
+ * @clk: Pointer to otg clock
+ * @reset: Pointer to dwc2 reset controller
+ * @reset_ecc: Pointer to dwc2 optional reset controller in Stratix10.
+ * @regset: A pointer to a struct debugfs_regset32, which contains
+ * a pointer to an array of register definitions, the
+ * array size and the base address where the register bank
+ * is to be found.
+ * @bus_suspended: True if bus is suspended
+ * @last_frame_num: Number of last frame. Range from 0 to 32768
+ * @frame_num_array: Used only if CONFIG_USB_DWC2_TRACK_MISSED_SOFS is
+ * defined, for missed SOFs tracking. Array holds that
+ * frame numbers, which not equal to last_frame_num +1
+ * @last_frame_num_array: Used only if CONFIG_USB_DWC2_TRACK_MISSED_SOFS is
+ * defined, for missed SOFs tracking.
+ * If current_frame_number != last_frame_num+1
+ * then last_frame_num added to this array
+ * @frame_num_idx: Actual size of frame_num_array and last_frame_num_array
+ * @dumped_frame_num_array: 1 - if missed SOFs frame numbers dumbed
+ * 0 - if missed SOFs frame numbers not dumbed
+ * @fifo_mem: Total internal RAM for FIFOs (bytes)
+ * @fifo_map: Each bit intend for concrete fifo. If that bit is set,
+ * then that fifo is used
+ * @gadget: Represents a usb slave device
+ * @connected: Used in slave mode. True if device connected with host
+ * @eps_in: The IN endpoints being supplied to the gadget framework
+ * @eps_out: The OUT endpoints being supplied to the gadget framework
+ * @new_connection: Used in host mode. True if there are new connected
+ * device
+ * @enabled: Indicates the enabling state of controller
+ *
*/
struct dwc2_hsotg {
struct device *dev;
unsigned int gadget_enabled:1;
unsigned int ll_hw_enabled:1;
unsigned int hibernated:1;
+ u16 frame_number;
struct phy *phy;
struct usb_phy *uphy;
u16 periodic_usecs;
unsigned long hs_periodic_bitmap[
DIV_ROUND_UP(DWC2_HS_SCHEDULE_US, BITS_PER_LONG)];
- u16 frame_number;
u16 periodic_qh_count;
bool bus_suspended;
bool new_connection;
projects / linux.git / blobdiff